phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
Lad Prabhakar [Thu, 21 Aug 2025 15:59:57 +0000 (16:59 +0100)]
phy: renesas: rcar-gen3-usb2: Fix ID check logic with VBUS valid
The existing ID detection logic returned false when both IDDIG and
VBUSVALID were set, which caused incorrect role determination in some
cases. The condition:
!(device && !vbus_valid)
did not properly reflect the intended relationship between IDDIG and
VBUSVALID signals.
Update the logic to:
return vbus_valid ? device : !device;
This ensures that when VBUS is valid, the role follows the IDDIG value,
and when VBUS is not valid, the role is inverted, matching the expected
OTG behavior.
Josua Mayer [Tue, 26 Aug 2025 18:32:03 +0000 (20:32 +0200)]
phy: lynx-28g: check return value when calling lynx_28g_pll_get
The lynx_28g_pll_get function may return NULL when called with an
unsupported submode argument.
This function is only called from the lynx_28g_lane_set_{10gbaser,sgmii}
functions, and lynx_28g_set_mode checks available modes before setting a
protocol.
NXP vendor kernel based on v6.6.52 however is missing any checks and
connecting a 2.5/5gbase-t ethernet phy can cause null pointer
dereference [1].
Check return value at every invocation and abort in the unlikely error
case. Further print a warning message the first time lynx_28g_pll_get
returns null, to catch this case should it occur after future changes.
Nitin Rawat [Sat, 30 Aug 2025 07:03:53 +0000 (12:33 +0530)]
phy: qcom-qmp-ufs: Add PHY and PLL regulator load
Add phy and pll regulator load voting support for all supported
platforms by introducing dedicated regulator bulk data arrays
with their load values.
This ensures stable operation and proper power management for these
platforms where regulators are shared between the QMP UFS PHY and
other IP blocks by setting appropriate regulator load currents during
PHY operations.
Nitin Rawat [Sat, 30 Aug 2025 07:03:52 +0000 (12:33 +0530)]
phy: qcom-qmp-ufs: Add regulator load voting for UFS QMP PHY
On certain SoCs, power regulators are shared between the QMP UFS PHY
and other IP blocks. To ensure proper operation, the regulator
framework must be informed of the UFS PHY's load requirements.
This is essential because the regulator's operating mode—whether Low
Power or High Power—depends on the maximum expected load at any given
time, which the regulator driver needs to manage accordingly.
To support this, replace devm_regulator_bulk_get() with
devm_regulator_bulk_get_const() and inline the qmp_ufs_vreg_init()
function. additionally replace the array of regulator names with a
bulk regulator data structure, and utilize the init_load_uA field
provided by the regulator framework. This ensures that
regulator_set_load() is automatically invoked before the
first enable operation.
phy: ingenic: use core driver model helper to handle probe errors
Use core driver model helper dev_err_probe() defined at
drivers/base/core.c in driver probe path to propagate errors.
standardize and improve the code of deferred probe error handling
using this helper for ingenic usb phy driver.
Inspired by,
commit a787e5400a1ce ("driver core: add device probe log helper")
Lad Prabhakar [Fri, 8 Aug 2025 21:52:09 +0000 (22:52 +0100)]
phy: renesas: rcar-gen3-usb2: Move debug print after register value is updated
Relocate the debug print in rcar_gen3_enable_vbus_ctrl() to appear after
the `val` variable is assigned and updated based on the VBUS state. This
ensures that the debug log reflects the actual register value being
written, improving debugging accuracy.
Lad Prabhakar [Fri, 8 Aug 2025 21:52:08 +0000 (22:52 +0100)]
phy: renesas: rcar-gen3-usb2: Add support for RZ/T2H SoC
Add initial support for the Renesas RZ/T2H SoC to the R-Car Gen3 USB2 PHY
driver. The RZ/T2H SoC requires configuration of additional
hardware-specific bits for proper VBUS level control and OTG operation.
Introduce the `vblvl_ctrl` flag in the SoC-specific driver data to enable
handling of VBUS level selection logic using `VBCTRL.VBLVL` bits. This is
required for managing the VBUS status detection and drive logic based on
SoC-specific needs.
Lad Prabhakar [Fri, 8 Aug 2025 21:52:07 +0000 (22:52 +0100)]
phy: renesas: rcar-gen3-usb2: Allow SoC-specific OBINT bits via phy_data
Update the PHY driver to support SoC-specific OBINT enable bits by
introducing the `obint_enable_bits` field in the `rcar_gen3_phy_drv_data`
structure. This allows each SoC to specify bits required.
Lad Prabhakar [Fri, 8 Aug 2025 21:52:06 +0000 (22:52 +0100)]
phy: renesas: rcar-gen3-usb2: store drvdata pointer in channel
Store the SoC-specific driver data pointer (struct rcar_gen3_phy_drv_data)
directly in struct rcar_gen3_chan instead of copying individual flags into
separate channel members.
Obtain the drvdata with of_device_get_match_data() in probe and assign it
to channel->phy_data. Update all call sites to reference
`channel->phy_data->*` for SoC-specific behaviour (for example no_adp_ctrl
and utmi_ctrl). Remove the redundant soc_no_adp_ctrl and utmi_ctrl fields
from struct rcar_gen3_chan.
This simplifies the probe path, reduces duplication, and makes it easier
to extend the driver with additional platform-specific fields in the
future.
Lad Prabhakar [Fri, 8 Aug 2025 21:52:05 +0000 (22:52 +0100)]
dt-bindings: phy: renesas,usb2-phy: Add RZ/T2H and RZ/N2H support
Document the USB2 PHY controller for the Renesas RZ/T2H (r9a09g077) and
RZ/N2H (r9a09g087) SoCs. These SoCs share the same PHY block, which is
similar to the one on RZ/G2L but differs in clocks, resets, and register
bits. To account for these differences, a new compatible string
`renesas,usb2-phy-r9a09g077` is introduced.
The RZ/N2H SoC uses the same PHY as RZ/T2H, so it reuses the RZ/T2H
compatible string as a fallback.
Neil Armstrong [Thu, 7 Aug 2025 16:33:23 +0000 (18:33 +0200)]
phy: qcom: qmp-combo: register a typec mux to change the QMPPHY_MODE
Register a typec mux in order to change the PHY mode on the Type-C
mux events depending on the mode and the svid when in Altmode setup.
The DisplayPort phy should be left enabled if is still powered on
by the DRM DisplayPort controller, so bail out until the DisplayPort
PHY is not powered off.
The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
will be set in between of USB-Only, Combo and DisplayPort Only so
this will leave enough time to the DRM DisplayPort controller to
turn of the DisplayPort PHY.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[konrad: renaming, rewording, bug fixes] Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-5-43272d6eca92@oss.qualcomm.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
Neil Armstrong [Thu, 7 Aug 2025 16:33:19 +0000 (18:33 +0200)]
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch
The QMP USB3/DP Combo PHY can work in 3 modes:
- DisplayPort Only
- USB3 Only
- USB3 + DisplayPort Combo mode
In order to switch between those modes, the PHY needs to receive
Type-C events, allow marking to the phy with the mode-switch
property in order to allow the PHY to Type-C events.
Reference usb-switch.yaml as a simpler way to allow the mode-switch
property instead of duplicating the property definition.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-1-43272d6eca92@oss.qualcomm.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
Chen Ni [Thu, 14 Aug 2025 01:39:43 +0000 (09:39 +0800)]
phy: rockchip: naneng-combphy: Convert comma to semicolon
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Andre Przywara [Tue, 19 Aug 2025 00:15:22 +0000 (01:15 +0100)]
phy: sun4i-usb: drop num_phys assumption
So far we set a number of expected Allwinner USB PHY instances for any
given compatible string, and would fail if we do not find every PHY
described properly in the DT (missing reset/PMU/clocks).
This is somewhat redundant, as the DT only describes the resources for
the implemented PHYs, but goes in line with being strict about firmware
descriptions, and rather fixing things in the driver code, based on the
compatible string.
However this causes issues when we make a mistake, like we did recently
on the A523: there are actually three USB PHYs, not two, as we assumed.
Changing the number in the driver and the compatible string would cause
all kinds of compatibility issues, both with older and newer DTs.
To avoid problems with newer kernels and older or newer DTs, we can change
the driver code to deduce the number of PHY instances from what's
described in the DT. This has the added advantage of not requiring new
compatible strings for new SoCs when just the number of PHYs change, which
already happened and might occur again in the future.
Drop the num_phys member from the config struct, and remove the fixed
number of PHYs from each SoC's config description. Then enumerate the
usb<x>_reset properties for all of the maximum four PHY instances, and
just stop once we cannot find such a property anymore.
The binding describes the reset property as mandatory for each PHY
instance, and each DT in the kernel tree matches exactly the num_phys
value in the current driver code, so we can rely on that.
Apart from being more future proof, this will solve the A523 mishap:
Older DTs would just describe two PHYs, whereas newer ones would feature
all three of them. In any case we would get a valid number, matching the
other nodes in the DT. Older kernels would always enumerate two PHYs,
which at least does not cause any regressions.
phy: qualcomm: phy-qcom-eusb2-repeater: Add support for PMIV0104
Add support for the eUSB2 repeater found on the PMIV0104. There is no
default init table for this PMIC, just the board-specific tuning
parameters are used on top of the default tuning values.
Document the FS Differential TX Output Resistance Tuning value found on
the eUSB2 repeater on Qualcomm PMICs. The tuning values have special
meanings, being different offsets of the resistance to the default value
in Ohms but the exact meaning is not relevant here, as the correct
tuning is determined by hardware engineers to make sure the electrical
properties are as expected.
Johan Hovold [Thu, 24 Jul 2025 15:48:23 +0000 (17:48 +0200)]
phy: ti: omap-control: drop unused module alias
Since commit 4fd06af96b93 ("usb: phy: omap-control: Get rid of platform
data") the driver only supports OF probe so drop the unused platform
module alias.
Johan Hovold [Thu, 24 Jul 2025 15:48:21 +0000 (17:48 +0200)]
phy: ti: ti-pipe3: drop unused module alias
Since commit 918ee0d21ba4 ("usb: phy: omap-usb3: Don't use
omap_get_control_dev()") the driver only supports OF probe so drop the
unused platform module alias.
Johan Hovold [Thu, 24 Jul 2025 15:48:20 +0000 (17:48 +0200)]
phy: ti: omap-usb2: drop unused module alias
Since commit 478b6c7436c2 ("usb: phy: omap-usb2: Don't use
omap_get_control_dev()") the driver only supports OF probe so drop the
unused platform module alias.
Johan Hovold [Thu, 24 Jul 2025 15:48:14 +0000 (17:48 +0200)]
phy: broadcom: brcm-usb: drop unused module alias
Since commit 9d5f51dcdb64 ("phy: usb: Add support for new Synopsys USB
controller on the 7211b0") the driver only supports OF probe so drop the
unused platform module alias.
Yao Zi [Mon, 28 Jul 2025 10:29:47 +0000 (10:29 +0000)]
phy: rockchip: naneng-combphy: Add RK3528 support
Rockchip RK3528 integrates one naneng-combphy that is able to operate in
PCIe and USB3 mode. The control logic is similar to previous variants of
naneng-combphy but the register layout is apparently different from the
RK3568 one.
Yao Zi [Mon, 28 Jul 2025 10:29:46 +0000 (10:29 +0000)]
phy: rockchip: naneng-combphy: Add SoC prefix to register definitions
All supported variants of naneng-combphy follow a register layout
similar to the RK3568 variant with some exceptions of SoC-specific
registers.
Add RK3568 prefix for the common set of registers and the corresponding
SoC prefix for SoC-specific registers, making usage of definitions clear
and preparing for future COMBPHY variants with a different register
layout.
Though isn't described in existing devicetrees, most Rockchip combphys
belong to a specific power-domain of the SoC. Taking RK3588 as example,
combphy 0 and combphy 2 belong to the PD_BUS domain. Document the
power-domains property to allow describing the information correctly
in devicetree.
Jonas Karlman [Wed, 23 Jul 2025 07:23:22 +0000 (07:23 +0000)]
phy: rockchip: naneng-combphy: Enable U3 OTG port for RK3568
The boot firmware may disable the U3 port early during boot and leave it
up to the controller or PHY driver to re-enable U3 when needed.
The Rockchip USBDP PHY driver currently does this for RK3576 and RK3588,
something the Rockchip Naneng Combo PHY driver never does for RK3568.
This may result in USB 3.0 ports being limited to only using USB 2.0 or
in special cases not working at all on RK3568.
Write to PIPE_GRF USB3OTGx_CON1 reg to ensure the U3 port is enabled
when a PHY with PHY_TYPE_USB3 mode is used.
Tomi Valkeinen [Wed, 23 Jul 2025 10:01:29 +0000 (13:01 +0300)]
phy: cdns-dphy: Remove leftover code
The code in cdns-dphy has probably been part of a DSI driver in the
past. Remove DSI defines and variables which are not used or do not
actually do anything. Also rename cdns_dsi_get_dphy_pll_cfg() to
cdns_dphy_get_pll_cfg(), i.e. drop the "dsi", as it's not relevant here.
Tomi Valkeinen [Wed, 23 Jul 2025 10:01:28 +0000 (13:01 +0300)]
phy: cdns-dphy: Store hs_clk_rate and return it
The DPHY driver does not return the actual hs_clk_rate, so the DSI
driver has no idea what clock was actually achieved. Set the realized
hs_clk_rate to the opts struct, so that the DSI driver gets it back.
Linus Torvalds [Sun, 10 Aug 2025 05:51:37 +0000 (08:51 +0300)]
Merge tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp fixes from Borislav Petkov:
- Remove an obsolete comment and fix spelling
* tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Remove obsolete comment from takedown_cpu()
smp: Fix spelling in on_each_cpu_cond_mask()'s doc-comment
Linus Torvalds [Sun, 10 Aug 2025 05:46:47 +0000 (08:46 +0300)]
Merge tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Fix a wrong ioremap size in mvebu-gicp
- Remove yet another compile-test case for a driver which needs an
additional dependency
- Fix a lock inversion scenario in the IRQ unit test suite
- Remove an impossible flag situation in gic-v5
- Do not iounmap resources in gic-v5 which are managed by devm
- Make sure stale, left-over interrupts in mvebu-gicp are cleared on
driver init
- Fix a reference counting mishap in msi-lib
- Fix a dereference-before-null-ptr-check case in the riscv-imsic
irqchip driver
* tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mvebu-gicp: Use resource_size() for ioremap()
irqchip: Build IMX_MU_MSI only on ARM
genirq/test: Resolve irq lock inversion warnings
irqchip/gic-v5: Remove IRQD_RESEND_WHEN_IN_PROGRESS for ITS IRQs
irqchip/gic-v5: iwb: Fix iounmap probe failure path
irqchip/mvebu-gicp: Clear pending interrupts on init
irqchip/msi-lib: Fix fwnode refcount in msi_lib_irq_domain_select()
irqchip/riscv-imsic: Don't dereference before NULL pointer check
Linus Torvalds [Sun, 10 Aug 2025 05:15:32 +0000 (08:15 +0300)]
Merge tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix an interrupt vector setup race which leads to a non-functioning
device
- Add new Intel CPU models *and* a family: 0x12. Finally. Yippie! :-)
* tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Plug vector setup race
x86/cpu: Add new Intel CPU model numbers for Wildcatlake and Novalake
Len Brown [Sun, 10 Aug 2025 01:08:26 +0000 (21:08 -0400)]
tools/power turbostat: version 2025.09.09
Probe and display L3 Cache topology
Add ability to average an added counter
(useful for pre-integrated "counters", such as Watts)
Break the limit of 64 built-in counters.
Assorted bug fixes and minor feature tweaks
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/
may be readable by all, but
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/current_freq_khz
may be readable only by root.
Non-root turbostat users see complaints in this scenario.
Fail probe of the interface if we can't read current_freq_khz.
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Original-patch-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 11 Jun 2025 06:50:26 +0000 (14:50 +0800)]
tools/power turbostat: Fix DMR support
Together with the RAPL MSRs, there are more MSRs gone on DMR, including
PLR (Perf Limit Reasons), and IRTL (Package cstate Interrupt Response
Time Limit) MSRs. The configurable TDP info should also be retrieved
from TPMI based Intel Speed Select Technology feature.
Remove the access of these MSRs for DMR. Improve the DMR platform
feature table to make it more readable at the same time.
Fixes: 83075bd59de2 ("tools/power turbostat: Add initial support for DMR") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
tools/power turbostat: add format "average" for external attributes
External atributes with format "raw" are not printed in summary lines
for nodes/packages (or with option -S). The new format "average"
behaves like "raw" but also adds the summary data
Signed-off-by: Michael Hebenstreit <michael.hebenstreit@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 12 Jul 2025 20:16:56 +0000 (16:16 -0400)]
tools/power turbostat: Support more than 64 built-in-counters
We have out-grown the ability to use a 64-bit memory location
to inventory every possible built-in counter.
Leverage the the CPU_SET(3) macros to break this barrier.
Also, break the Joules & Watts counters into two,
since we can no longer 'or' them together...
Linus Torvalds [Sat, 9 Aug 2025 15:12:23 +0000 (18:12 +0300)]
Merge tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fix from Greg KH:
"Here is a single revert of one of the previous patches that went in
the last tty/serial merge that is breaking userspace on some platforms
(specifically powerpc, probably a few others.)
It accidentially changed the ioctl values of some tty ioctls, which
breaks xorg.
The revert has been in linux-next all this week with no reported
issues"
* tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: vt: use _IO() to define ioctl numbers"
Linus Torvalds [Sat, 9 Aug 2025 05:47:28 +0000 (08:47 +0300)]
Merge tag 'block-6.17-20250808' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Yu:
- mddev null-ptr-dereference fix, by Erkun
- md-cluster fail to remove the faulty disk regression fix, by
Heming
- minor cleanup, by Li Nan and Jinchao
- mdadm lifetime regression fix reported by syzkaller, by Yu Kuai
- MD pull request via Christoph
- add support for getting the FDP featuee in fabrics passthru path
(Nitesh Shetty)
- add capability to connect to an administrative controller
(Kamaljit Singh)
- fix a leak on sgl setup error (Keith Busch)
- initialize discovery subsys after debugfs is initialized
(Mohamed Khalfella)
- fix various comment typos (Bjorn Helgaas)
- remove unneeded semicolons (Jiapeng Chong)
- nvmet debugfs ordering issue fix
- Fix UAF in the tag_set in zloop
- Ensure sbitmap shallow depth covers entire set
- Reduce lock roundtrips in io context lookup
- Move scheduler tags alloc/free out of elevator and freeze lock, to
fix some lockdep found issues
- Improve robustness of queue limits checking
- Fix a regression with IO priorities, if no io context exists
* tag 'block-6.17-20250808' of git://git.kernel.dk/linux: (26 commits)
lib/sbitmap: make sbitmap_get_shallow() internal
lib/sbitmap: convert shallow_depth from one word to the whole sbitmap
nvmet: exit debugfs after discovery subsystem exits
block, bfq: Reorder struct bfq_iocq_bfqq_data
md: make rdev_addable usable for rcu mode
md/raid1: remove struct pool_info and related code
md/raid1: change r1conf->r1bio_pool to a pointer type
block: ensure discard_granularity is zero when discard is not supported
zloop: fix KASAN use-after-free of tag set
block: Fix default IO priority if there is no IO context
nvme: fix various comment typos
nvme-auth: remove unneeded semicolon
nvme-pci: fix leak on sgl setup error
nvmet: initialize discovery subsys after debugfs is initialized
nvme: add capability to connect to an administrative controller
nvmet: add support for FDP in fabrics passthru path
md: rename recovery_cp to resync_offset
md/md-cluster: handle REMOVE message earlier
md: fix create on open mddev lifetime regression
block: fix potential deadlock while running nr_hw_queue update
...
Linus Torvalds [Sat, 9 Aug 2025 05:45:08 +0000 (08:45 +0300)]
Merge tag 'io_uring-6.17-20250808' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Allow vectorized payloads for send/send-zc - like sendmsg, but
without the hassle of a msghdr.
- Fix for an integer wrap that should go to stable, spotted by syzbot.
Nothing alarming here, as you need to be root to hit this.
Nevertheless, it should get fixed.
FWIW, kudos to the syzbot crew for having much nicer reproducers now,
and with nicely annotated source code as well. This is particularly
useful as syzbot uses the raw interface rather than liburing,
historically it's been difficult to turn a syzbot reproducer into a
meaningful test case. With the recent changes, not true anymore!
* tag 'io_uring-6.17-20250808' of git://git.kernel.dk/linux:
io_uring/memmap: cast nr_pages to size_t before shifting
io_uring/net: Allow to do vectorized send
Linus Torvalds [Sat, 9 Aug 2025 05:43:24 +0000 (08:43 +0300)]
Merge tag 'spi-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There's one fix here for an issue with the CS42L43 where we were
allocating a single property for client devices as just that property
rather than a terminated array of properties like we are supposed to.
We also have an update to the MAINTAINERS file for some Renesas
devices"
* tag 'spi-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: cs42l43: Property entry should be a null-terminated array
MAINTAINERS: Add entries for the RZ/V2H(P) RSPI
Linus Torvalds [Sat, 9 Aug 2025 05:41:53 +0000 (08:41 +0300)]
Merge tag 'regulator-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"This fixes an issue with the newly added code for handling large
voltage changes on regulators which require that individual voltage
changes cover a limited range, the check for convergence was broken"
* tag 'regulator-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: correct convergence check in regulator_set_voltage()
Linus Torvalds [Sat, 9 Aug 2025 05:40:28 +0000 (08:40 +0300)]
Merge tag 'regmap-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"These patches fix a lockdep issue Russell King reported with nested
regmap-irqs (unusual since regmap is generally for devices on slow
buses so devices don't get nested), plus add a missing mutex free
which I noticed while implementing a fix for that issue"
* tag 'regmap-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: Avoid lockdep warnings with nested regmap-irq chips
regmap: irq: Free the regmap-irq mutex
Linus Torvalds [Sat, 9 Aug 2025 05:37:17 +0000 (08:37 +0300)]
Merge tag 'mailbox-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- aspeed: add driver and bindings for ast2700
- broadcom: add driver and bindings for bcm74110
- mediatek: fix RPM api usage
- qcom: use dev_fwnode
- pcc: support shared buffer
- misc dt-bindings cleanup
* tag 'mailbox-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox/pcc: support mailbox management of the shared buffer
mailbox: bcm74110: Fix spelling mistake
mailbox: bcm74110: remove unneeded semicolon
mailbox: aspeed: add mailbox driver for AST27XX series SoC
dt-bindings: mailbox: Add ASPEED AST2700 series SoC
dt-bindings: mailbox: Drop consumers example DTS
dt-bindings: mailbox: nvidia,tegra186-hsp: Use generic node name
dt-bindings: mailbox: Correct example indentation
dt-bindings: mailbox: ti,secure-proxy: Add missing reg maxItems
dt-bindings: mailbox: amlogic,meson-gxbb-mhu: Add missing interrupts maxItems
dt-bindings: mailbox: qcom-ipcc: document the Milos Inter-Processor Communication Controller
mailbox: Add support for bcm74110
dt-bindings: mailbox: Add support for bcm74110
mailbox: Use dev_fwnode()
mailbox: mtk-cmdq: Switch to pm_runtime_put_autosuspend()
Linus Torvalds [Sat, 9 Aug 2025 05:15:43 +0000 (08:15 +0300)]
Merge tag 'gpio-updates-for-v6.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"As discussed: there's a small commit that removes the legacy GPIO line
value setter callbacks as they're no longer used and a big, treewide
commit that renames the new ones to the old names across all GPIO
drivers at once.
While at it: there are also two fixes that I picked up over the course
of the merge window:
- remove unused, legacy GPIO line value setters from struct gpio_chip
- rename the new set callbacks back to the original names treewide
- fix interrupt handling in gpio-mlxbf2
- revert a buggy immutable irqchip conversion"
* tag 'gpio-updates-for-v6.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
treewide: rename GPIO set callbacks back to their original names
gpio: remove legacy GPIO line value setter callbacks
gpio: mlxbf2: use platform_get_irq_optional()
Revert "gpio: pxa: Make irq_chip immutable"
Linus Torvalds [Sat, 9 Aug 2025 05:12:41 +0000 (08:12 +0300)]
Merge tag 'sound-fix-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Support for ASoC AMD ACP 7.2 with new IDs
- ASoC Intel AVS and SOF fixes
- Yet more kconfig adjustments for HD-audio codecs
- TAS2781 codec fixes
- Fixes for longstanding (rather minor) bugs in Intel LPE audio and
USB-audio drivers
* tag 'sound-fix-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/cirrus: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/hdmi: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/realtek: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/ca0132: Fix missing error handling in ca0132_alt_select_out()
ASoC: SOF: Intel: hda-sdw-bpt: fix SND_SOF_SOF_HDA_SDW_BPT dependencies
ALSA: hda/tas2781: Support L"SmartAmpCalibrationData" to save calibrated data
ALSA: intel_hdmi: Fix off-by-one error in __hdmi_lpe_audio_probe()
ALSA: hda/realtek: add LG gram 16Z90R-A to alc269 fixup table
ALSA: usb-audio: Don't use printk_ratelimit for debug prints
ASoC: Intel: sof_sdw: Add quirk for Alienware Area 51 (2025) 0CCC SKU
ASoC: tas2781: Fix the wrong step for TLV on tas2781
ASoC: amd: acp: Add SoundWire SOF machine driver support for acp7.2 platform
ASoC: amd: acp: Add SoundWire legacy machine driver support for acp7.2 platform
ASoC: amd: ps: Add SoundWire pci and dma driver support for acp7.2 platform
ASoC: SOF: amd: Add sof audio support for acp7.2 platform
ASoC: Intel: avs: Fix uninitialized pointer error in probe()
ASoC: wm8962: Clear master mode when enter runtime suspend
ASoC: SOF: amd: acp-loader: Use GFP_KERNEL for DMA allocations in resume context
Linus Torvalds [Sat, 9 Aug 2025 04:58:55 +0000 (07:58 +0300)]
Merge tag 'soc-fixes-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"These are a few patches to fix up bits that went missing during the
merge window: The tegra and s3c patches address trivial regressions
from conflicts, the bcm7445 makes the dt conform to the binding that
was made stricter"
* tag 'soc-fixes-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: tegra: Remove numa-node-id properties
ARM: s3c/gpio: complete the conversion to new GPIO value setters
ARM: dts: broadcom: Fix bcm7445 memory controller compatible
Linus Torvalds [Sat, 9 Aug 2025 04:35:03 +0000 (07:35 +0300)]
Merge tag 'xtensa-20250808' of https://github.com/jcmvbkbc/linux-xtensa
Pull xtensa update from Max Filippov:
- replace __ASSEMBLY__ with __ASSEMBLER__ in arch headers
* tag 'xtensa-20250808' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: Replace __ASSEMBLY__ with __ASSEMBLER__ in non-uapi headers
xtensa: Replace __ASSEMBLY__ with __ASSEMBLER__ in uapi headers
Linus Torvalds [Sat, 9 Aug 2025 04:26:19 +0000 (07:26 +0300)]
Merge tag 'v6.17-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a regression that broke hmac(sha3-224-s390)"
* tag 'v6.17-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hash - Increase HASH_MAX_DESCSIZE for hmac(sha3-224-s390)
Linus Torvalds [Sat, 9 Aug 2025 04:20:44 +0000 (07:20 +0300)]
Merge tag 'nfs-for-6.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- don't inherit NFS filesystem capabilities when crossing from one
filesystem to another
Bugfixes:
- NFS wakeup of __nfs_lookup_revalidate() needs memory barriers
- NFS improve bounds checking in nfs_fh_to_dentry()
- NFS Fix allocation errors when writing to a NFS file backed
loopback device
- NFSv4: More listxattr fixes
- SUNRPC: fix client handling of TLS alerts
- pNFS block/scsi layout fix for an uninitialised pointer
dereference
- pNFS block/scsi layout fixes for the extent encoding, stripe
mapping, and disk offset overflows
- pNFS layoutcommit work around for RPC size limitations
- pNFS/flexfiles avoid looping when handling fatal errors after
layoutget
- localio: fix various race conditions
Features and cleanups:
- Add NFSv4 support for retrieving the btime
- NFS: Allow folio migration for the case of mode == MIGRATE_SYNC
- NFS: Support using a kernel keyring to store TLS certificates
- NFSv4: Speed up delegation lookup using a hash table
- Assorted cleanups to remove unused variables and struct fields
- Assorted new tracepoints to improve debugging"
* tag 'nfs-for-6.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (44 commits)
NFS/localio: nfs_uuid_put() fix the wake up after unlinking the file
NFS/localio: nfs_uuid_put() fix races with nfs_open/close_local_fh()
NFS/localio: nfs_close_local_fh() fix check for file closed
NFSv4: Remove duplicate lookups, capability probes and fsinfo calls
NFS: Fix the setting of capabilities when automounting a new filesystem
sunrpc: fix client side handling of tls alerts
nfs/localio: use read_seqbegin() rather than read_seqbegin_or_lock()
NFS: Fixup allocation flags for nfsiod's __GFP_NORETRY
NFSv4.2: another fix for listxattr
NFS: Fix filehandle bounds checking in nfs_fh_to_dentry()
SUNRPC: Silence warnings about parameters not being described
NFS: Clean up pnfs_put_layout_hdr()/pnfs_destroy_layout_final()
NFS: Fix wakeup of __nfs_lookup_revalidate() in unblock_revalidate()
NFS: use a hash table for delegation lookup
NFS: track active delegations per-server
NFS: move the delegation_watermark module parameter
NFS: cleanup nfs_inode_reclaim_delegation
NFS: cleanup error handling in nfs4_server_common_setup
pNFS/flexfiles: don't attempt pnfs on fatal DS errors
NFS: drop __exit from nfs_exit_keyring
...
Linus Torvalds [Sat, 9 Aug 2025 04:12:43 +0000 (07:12 +0300)]
Merge tag 'v6.17rc-part2-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
"Non-smbdirect:
- Fix null ptr deref caused by delay in global spinlock
initialization
- Two fixes for native symlink creation with SMB3.1.1 POSIX
Extensions
- Fix for socket special file creation with SMB3.1.1 POSIX Exensions
- Reduce lock contention by splitting out mid_counter_lock
- move SMB1 transport code to separate file to reduce module size
when support for legacy servers is disabled
- Two cleanup patches: rename mid_lock to make it clearer what it
protects and one to convert mid flags to bool to make clearer
Smbdirect/RDMA restructuring and fixes:
- Fix for error handling in send done
- Remove unneeded empty packet queue
- Fix put_receive_buffer error path
- Two fixes to recv_done error paths
- Remove unused variable
- Improve response and recvmsg type handling
- Fix handling of incoming message type
- Two cleanup fixes for better handling smbdirect recv io
- Two cleanup fixes for socket spinlock
- Two patches that add socket reassembly struct
- Remove unused connection_status enum
- Use flag in common header for SMBDIRECT_RECV_IO_MAX_SGE
- Two cleanup patches to introduce and use smbdirect send io
- Two cleanup patches to introduce and use smbdirect send_io struct
- Fix to return error if rdma connect takes longer than 5 seconds
- Error logging improvements
- Fix redundand call to init_waitqueue_head
- Remove unneeded wait queue"
* tag 'v6.17rc-part2-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6: (33 commits)
smb: client: only use a single wait_queue to monitor smbdirect connection status
smb: client: don't call init_waitqueue_head(&info->conn_wait) twice in _smbd_get_connection
smb: client: improve logging in smbd_conn_upcall()
smb: client: return an error if rdma_connect does not return within 5 seconds
smb: client: make use of smbdirect_socket.{send,recv}_io.mem.{cache,pool}
smb: smbdirect: add smbdirect_socket.{send,recv}_io.mem.{cache,pool}
smb: client: make use of struct smbdirect_send_io
smb: smbdirect: introduce struct smbdirect_send_io
smb: client: make use of SMBDIRECT_RECV_IO_MAX_SGE
smb: smbdirect: add SMBDIRECT_RECV_IO_MAX_SGE
smb: client: remove unused enum smbd_connection_status
smb: client: make use of smbdirect_socket.recv_io.reassembly.*
smb: smbdirect: introduce smbdirect_socket.recv_io.reassembly.*
smb: client: make use of smb: smbdirect_socket.recv_io.free.{list,lock}
smb: smbdirect: introduce smbdirect_socket.recv_io.free.{list,lock}
smb: client: make use of struct smbdirect_recv_io
smb: smbdirect: introduce struct smbdirect_recv_io
smb: client: make use of smbdirect_socket->recv_io.expected
smb: smbdirect: introduce smbdirect_socket.recv_io.expected
smb: client: remove unused smbd_connection->fragment_reassembly_remaining
...
Linus Torvalds [Sat, 9 Aug 2025 03:52:37 +0000 (06:52 +0300)]
Merge tag 'v6.17rc-part2-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
- Fix limiting repeated connections from same IP
- Fix for extracting shortname when name begins with a dot
- Four smbdirect fixes:
- three fixes to the receive path: potential unmap bug, potential
resource leaks and stale connections, and also potential use
after free race
- cleanup to remove unneeded queue
* tag 'v6.17rc-part2-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
smb: server: Fix extension string in ksmbd_extract_shortname()
ksmbd: limit repeated connections from clients with the same IP
smb: server: let recv_done() avoid touching data_transfer after cleanup/move
smb: server: let recv_done() consistently call put_recvmsg/smb_direct_disconnect_rdma_connection
smb: server: make sure we call ib_dma_unmap_single() only if we called ib_dma_map_single already
smb: server: remove separate empty_recvmsg_queue
Zhang Rui [Tue, 17 Jun 2025 12:48:59 +0000 (20:48 +0800)]
tools/power turbostat: Fix bogus SysWatt for forked program
Similar to delta_cpu(), delta_platform() is called in turbostat main
loop. This ensures accurate SysWatt readings in periodic monitoring mode
$ sudo turbostat -S -q --show power -i 1
CoreTmp PkgTmp PkgWatt CorWatt GFXWatt RAMWatt PKG_% RAM_% SysWatt
60 61 6.21 1.13 0.16 0.00 0.00 0.00 13.07
58 61 6.00 1.07 0.18 0.00 0.00 0.00 12.75
58 61 5.74 1.05 0.17 0.00 0.00 0.00 12.22
58 60 6.27 1.11 0.24 0.00 0.00 0.00 13.55
However, delta_platform() is missing for forked program and causes bogus
SysWatt reporting,
$ sudo turbostat -S -q --show power sleep 1
1.004736 sec
CoreTmp PkgTmp PkgWatt CorWatt GFXWatt RAMWatt PKG_% RAM_% SysWatt
57 58 6.05 1.02 0.16 0.00 0.00 0.00 0.03
Add missing delta_platform() for forked program.
Fixes: e5f687b89bc2 ("tools/power turbostat: Add RAPL psys as a built-in counter") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Kernels configured with CONFIG_MULTIUSER=n have no cap_get_proc().
Check for ENOSYS to recognize this case, and continue on to
attempt to access the requested MSRs (such as temperature).
Signed-off-by: Calvin Owens <calvin@wbinvd.org> Signed-off-by: Len Brown <len.brown@intel.com>
Calvin Owens [Fri, 13 Jun 2025 16:54:23 +0000 (09:54 -0700)]
tools/power turbostat: Fix build with musl
turbostat.c: In function 'parse_int_file':
turbostat.c:5567:19: error: 'PATH_MAX' undeclared (first use in this function)
5567 | char path[PATH_MAX];
| ^~~~~~~~
turbostat.c: In function 'probe_graphics':
turbostat.c:6787:19: error: 'PATH_MAX' undeclared (first use in this function)
6787 | char path[PATH_MAX];
| ^~~~~~~~
Signed-off-by: Calvin Owens <calvin@wbinvd.org> Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Jens Axboe [Fri, 8 Aug 2025 12:35:14 +0000 (06:35 -0600)]
io_uring/memmap: cast nr_pages to size_t before shifting
If the allocated size exceeds UINT_MAX, then it's necessary to cast
the mr->nr_pages value to size_t to prevent it from overflowing. In
practice this isn't much of a concern as the required memory size will
have been validated upfront, and accounted to the user. And > 4GB sizes
will be necessary to make the lack of a cast a problem, which greatly
exceeds normal user locked_vm settings that are generally in the kb to
mb range. However, if root is used, then accounting isn't done, and
then it's possible to hit this issue.
Adam Young [Tue, 15 Jul 2025 00:10:07 +0000 (20:10 -0400)]
mailbox/pcc: support mailbox management of the shared buffer
Define a new, optional, callback that allows the driver to
specify how the return data buffer is allocated. If that callback
is set, mailbox/pcc.c is now responsible for reading from and
writing to the PCC shared buffer.
This also allows for proper checks of the Commnand complete flag
between the PCC sender and receiver.
For Type 4 channels, initialize the command complete flag prior
to accepting messages.
Since the mailbox does not know what memory allocation scheme
to use for response messages, the client now has an optional
callback that allows it to allocate the buffer for a response
message.
When an outbound message is written to the buffer, the mailbox
checks for the flag indicating the client wants an tx complete
notification via IRQ. Upon receipt of the interrupt It will
pair it with the outgoing message. The expected use is to
free the kernel memory buffer for the previous outgoing message.
Signed-off-by: Adam Young <admiyo@os.amperecomputing.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
- net: drop UFO packets (injected via virtio) in udp_rcv_segment()
- eth: mlx5: correctly set gso_segs when LRO is used, avoid false
positive checksum validation errors
- netpoll: prevent hanging NAPI when netcons gets enabled
- phy: mscc: fix parsing of unicast frames for PTP timestamping
- a number of device tree / OF reference leak fixes"
* tag 'net-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (44 commits)
pptp: fix pptp_xmit() error path
net: ti: icssg-prueth: Fix skb handling for XDP_PASS
net: Update threaded state in napi config in netif_set_threaded
selftests: netdevsim: Xfail nexthop test on slow machines
eth: fbnic: Lock the tx_dropped update
eth: fbnic: Fix tx_dropped reporting
eth: fbnic: remove the debugging trick of super high page bias
net: ftgmac100: fix potential NULL pointer access in ftgmac100_phy_disconnect
dt-bindings: net: Replace bouncing Alexandru Tachici emails
dpll: zl3073x: ZL3073X_I2C and ZL3073X_SPI should depend on NET
net/sched: mqprio: fix stack out-of-bounds write in tc entry parsing
Revert "net: mdio_bus: Use devm for getting reset GPIO"
selftests: net: packetdrill: xfail all problems on slow machines
net/packet: fix a race in packet_set_ring() and packet_notifier()
benet: fix BUG when creating VFs
net: airoha: npu: Add missing MODULE_FIRMWARE macros
net: devmem: fix DMA direction on unmapping
ipa: fix compile-testing with qcom-mdt=m
eth: fbnic: unlink NAPIs from queues on error to open
net: Add locking to protect skb->dev access in ip_output
...
Linus Torvalds [Fri, 8 Aug 2025 03:56:55 +0000 (06:56 +0300)]
Merge tag 's390-6.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Support MMIO read/write tracing
- Enable THP swapping and THP migration
- Unmask SLCF bit ("stateless command filtering") introduced with CEX8
cards, so that user space applications like lszcrypt could evaluate
and list this feature
- Fix the value of high_memory variable, so it considers possible
tailing offline memory blocks
- Make vmem_pte_alloc() consistent and always allocate memory of
PAGE_SIZE for page tables. This ensures a page table occupies the
whole page, as the rest of the code assumes
- Fix kernel image end address in the decompressor debug output
- Fix a typo in debug_sprintf_format_fn() comment
* tag 's390-6.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/debug: Fix typo in debug_sprintf_format_fn() comment
s390/boot: Fix startup debugging log
s390/mm: Allocate page table with PAGE_SIZE granularity
s390/mm: Enable THP_SWAP and THP_MIGRATION
s390: Support CONFIG_TRACE_MMIO_ACCESS
s390/mm: Set high_memory at the end of the identity mapping
s390/ap: Unmask SLCF bit in card and queue ap functions sysfs
Linus Torvalds [Fri, 8 Aug 2025 03:48:14 +0000 (06:48 +0300)]
Merge tag 'drm-next-2025-08-08' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"This is the fixes that built up in the merge window, mostly amdgpu and
xe with one i915 display fix, seems like things are pretty good for
rc1.
i915:
- DP LPFS fixes
xe:
- SRIOV: PF fixes and removal of need of module param
- Fix driver unbind around Devcoredump
- Mark xe driver as BROKEN if kernel page size is not 4kB
* tag 'drm-next-2025-08-08' of https://gitlab.freedesktop.org/drm/kernel: (28 commits)
drm/amdgpu: add missing vram lost check for LEGACY RESET
drm/amdgpu/discovery: fix fw based ip discovery
drm/amdkfd: Destroy KFD debugfs after destroy KFD wq
amdgpu/amdgpu_discovery: increase timeout limit for IFWI init
drm/amdgpu: Update SDMA firmware version check for user queue support
drm/amdgpu: Add NULL check for asic_funcs
drm/amd/display: Revert "drm/amd/display: Fix AMDGPU_MAX_BL_LEVEL value"
drm/amd/display: fix a Null pointer dereference vulnerability
drm/amd/display: Add primary plane to commits for correct VRR handling
drm/amdgpu: update mmhub 3.3 client id mappings
drm/amdgpu: update mmhub 3.0.1 client id mappings
drm/amdgpu: Retain job->vm in amdgpu_job_prepare_job
drm/amd/display: Fix DCE 6.0 and 6.4 PLL programming.
drm/amd/display: Don't overwrite dce60_clk_mgr
drm/amdkfd: Fix checkpoint-restore on multi-xcc
drm/amd: Restore cached manual clock settings during resume
drm/amd: Restore cached power limit during resume
drm/amdgpu: Update external revid for GC v9.5.0
drm/amdgpu: Update supported modes for GC v9.5.0
Mark xe driver as BROKEN if kernel page size is not 4kB
...
Linus Torvalds [Fri, 8 Aug 2025 03:43:20 +0000 (06:43 +0300)]
Merge tag 'fbdev-for-6.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes for 6.17-rc1:
- Revert a patch which broke VGA console
- Fix an out-of-bounds access bug which may happen during console
resizing when a console is mapped to a frame buffer
* tag 'fbdev-for-6.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
Revert "vgacon: Add check for vc_origin address range in vgacon_scroll()"
fbdev: Fix vmalloc out-of-bounds write in fast_imageblit
Linus Torvalds [Fri, 8 Aug 2025 03:36:48 +0000 (06:36 +0300)]
Merge tag 'loongarch-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Complete KSave registers definition
- Support the mem=<size> kernel parameter
- Support BPF dynamic modification & trampoline
- Add MMC/SDIO controller nodes in dts
- Some bug fixes and other small changes
* tag 'loongarch-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: vDSO: Remove -nostdlib complier flag
LoongArch: dts: Add eMMC/SDIO controller support to Loongson-2K2000
LoongArch: dts: Add SDIO controller support to Loongson-2K1000
LoongArch: dts: Add SDIO controller support to Loongson-2K0500
LoongArch: BPF: Set bpf_jit_bypass_spec_v1/v4()
LoongArch: BPF: Fix the tailcall hierarchy
LoongArch: BPF: Fix jump offset calculation in tailcall
LoongArch: BPF: Add struct ops support for trampoline
LoongArch: BPF: Add basic bpf trampoline support
LoongArch: BPF: Add dynamic code modification support
LoongArch: BPF: Rename and refactor validate_code()
LoongArch: Add larch_insn_gen_{beq,bne} helpers
LoongArch: Don't use %pK through printk() in unwinder
LoongArch: Avoid in-place string operation on FDT content
LoongArch: Support mem=<size> kernel parameter
LoongArch: Make relocate_new_kernel_size be a .quad value
LoongArch: Complete KSave registers definition
Thorsten Blum [Wed, 6 Aug 2025 01:03:49 +0000 (03:03 +0200)]
smb: server: Fix extension string in ksmbd_extract_shortname()
In ksmbd_extract_shortname(), strscpy() is incorrectly called with the
length of the source string (excluding the NUL terminator) rather than
the size of the destination buffer. This results in "__" being copied
to 'extension' rather than "___" (two underscores instead of three).
Use the destination buffer size instead to ensure that the string "___"
(three underscores) is copied correctly.
Cc: stable@vger.kernel.org Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
projects / thirdparty / kernel / stable.git / log
