xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
On systems with 64k page size and 512M huge page sizes, the allocation and
test succeeds but errors out at the munmap. As the comment states, munmap
will failure if its not HUGEPAGE aligned. This is due to the length of
the mapping being 1/2 the size of the hugepage causing the munmap to not
be hugepage aligned. Fix this by making the mapping length the full
hugepage if the hugepage is larger than the length of the mapping.
Running charge_reserved_hugetlb.sh generates errors if sh is set to
dash:
./charge_reserved_hugetlb.sh: 9: [[: not found
./charge_reserved_hugetlb.sh: 19: [[: not found
./charge_reserved_hugetlb.sh: 27: [[: not found
./charge_reserved_hugetlb.sh: 37: [[: not found
./charge_reserved_hugetlb.sh: 45: Syntax error: "(" unexpected
Switch to using /bin/bash instead of /bin/sh. Make the switch for
write_hugetlb_memory.sh as well which is called from
charge_reserved_hugetlb.sh.
Link: https://lkml.kernel.org/r/20240116090455.3407378-1-usama.anjum@collabora.com Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Cc: Muhammad Usama Anjum <usama.anjum@collabora.com> Cc: Shuah Khan <shuah@kernel.org> Cc: David Laight <David.Laight@ACULAB.COM> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nfp offload flow pay will not allocate a mask id when the out port
is openvswitch internal port. This is because these flows are used to
configure the pre_tun table and are never actually send to the firmware
as an add-flow message. When a tc rule which action contains ct and
the post ct entry's out port is openvswitch internal port, the merge
offload flow pay with the wrong mask id of 0 will be send to the
firmware. Actually, the nfp can not support hardware offload for this
situation, so return EOPNOTSUPP.
Fixes: bd0fe7f96a3c ("nfp: flower-ct: add zone table entry when handling pre/post_ct flows") CC: stable@vger.kernel.org # 5.14+ Signed-off-by: Hui Zhou <hui.zhou@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20240124151909.31603-2-louis.peens@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The chain_index has different means in pre ct entry and post ct entry.
In pre ct entry, it means chain index, but in post ct entry, it means
goto chain index, it is confused.
chain_index and goto_chain_index may be present in one flow rule, It
cannot be distinguished by one field chain_index, both chain_index
and goto_chain_index are required in the follow-up patch to support
multiple ct zones
Another field goto_chain_index is added to record the goto chain index.
If no goto action in post ct entry, goto_chain_index is 0.
Signed-off-by: Wentao Jia <wentao.jia@corigine.com> Acked-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: cefa98e806fd ("nfp: flower: add hardware offload check for post ct entry") Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'status' variable in 'core_link_read_dpcd()' &
'core_link_write_dpcd()' was uninitialized.
Thus, initializing 'status' variable to 'DC_ERROR_UNEXPECTED' by default.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:226 core_link_read_dpcd() error: uninitialized symbol 'status'.
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:248 core_link_write_dpcd() error: uninitialized symbol 'status'.
Cc: stable@vger.kernel.org Cc: Jerry Zuo <jerry.zuo@amd.com> Cc: Jun Lei <Jun.Lei@amd.com> Cc: Wayne Lin <Wayne.Lin@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RODE NT-USB+ is marketed as a professional usb microphone, however the
usb audio interface is a mess:
[ 1.130977] usb 1-5: new full-speed USB device number 2 using xhci_hcd
[ 1.503906] usb 1-5: config 1 has an invalid interface number: 5 but max is 4
[ 1.503912] usb 1-5: config 1 has no interface number 4
[ 1.519689] usb 1-5: New USB device found, idVendor=19f7, idProduct=0035, bcdDevice= 1.09
[ 1.519695] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.519697] usb 1-5: Product: RØDE NT-USB+
[ 1.519699] usb 1-5: Manufacturer: RØDE
[ 1.519700] usb 1-5: SerialNumber: 1D773A1A
[ 8.327495] usb 1-5: 1:1: cannot get freq at ep 0x82
[ 8.344500] usb 1-5: 1:2: cannot get freq at ep 0x82
[ 8.365499] usb 1-5: 2:1: cannot get freq at ep 0x2
Add QUIRK_FLAG_GET_SAMPLE_RATE to work around the broken sample rate get.
I have asked Rode support to fix it, but they show no interest.
I own an external usb Webcam, model NexiGo N930AF, which had low mic volume and
inconsistent sound quality. Video works as expected.
(snip)
[ +0.047857] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.003406] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000007] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.003900] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
[ +0.025726] usb 5-1: 3:1: cannot get usb sound sample rate freq at ep 0x86
[ +0.071482] usb 5-1: 3:2: cannot get usb sound sample rate freq at ep 0x86
[ +0.004679] usb 5-1: 3:3: cannot get usb sound sample rate freq at ep 0x86
[ +0.051607] usb 5-1: Warning! Unlikely big volume range (=4096), cval->res is probably wrong.
[ +0.000005] usb 5-1: [7] FU [Mic Capture Volume] ch = 1, val = 0/4096/1
Set up quirk cval->res to 16 for 256 levels,
Set GET_SAMPLE_RATE quirk flag to stop trying to get the sample rate.
Confirmed that happened anyway later due to the backoff mechanism, after 3 failures
All audio stream on device interfaces share the same values,
apart from wMaxPacketSize and tSamFreq :
Based on the usb data about manufacturer, SPCA2281B3 is the most likely controller IC
Manufacturer does not provide link for datasheet nor detailed specs.
No way to confirm if the firmware supports any other way of getting the sample rate.
Testing patch provides consistent good sound recording quality and volume range.
(snip)
[ +0.045764] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.106290] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000006] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.043700] usb 5-1: set resolution quirk: cval->res = 16
[ +0.002585] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
It seems that the firmware is broken and does not accept
the UAC_EP_CS_ATTR_SAMPLE_RATE URB. There is only one rate (48000Hz)
available in the descriptors for the output endpoint.
Create a new quirk QUIRK_FLAG_FIXED_RATE to skip the rate setup
when only one rate is available (fixed).
Tascam's Model 12 is a mixer which can also operate as a USB audio
interface. The audio interface uses explicit feedback but it seems that
it does not correctly handle missing isochronous frames.
When injecting an xrun (or doing anything else that pauses the playback
stream) the feedback rate climbs (for example, at 44,100Hz nominal, I
see a stable rate around 44,099 but xrun injection sees this peak at
around 44,135 in most cases) and glitches are heard in the audio stream
for several seconds - this is significantly worse than the single glitch
expected for an underrun.
While the stream does normally recover and the feedback rate returns to
a stable value, I have seen some occurrences where this does not happen
and the rate continues to increase while no audio is heard from the
output. I have not found a solid reproduction for this.
This misbehaviour can be avoided by totally resetting the stream state
by switching the interface to alt 0 and back before restarting the
playback stream.
Add a new quirk flag which forces the endpoint and interface to be
reconfigured whenever the stream is stopped, and use this for the Tascam
Model 12.
Separate interfaces are used for the playback and capture endpoints, so
resetting the playback interface here will not affect the capture stream
if it is running. While there are two endpoints on the interface,
these are the OUT data endpoint and the IN explicit feedback endpoint
corresponding to it and these are always stopped and started together.
After splitting to snd_usb_endpoint_set_params() and *_prepare(), the
skip of each function should be checked with different flags, while we
still use ep->need_setup as the single one. Introduce
ep->need_prepare for indicating the need of prepare, and also add the
missing check of ep->need_setup at the set_params.
The protection with chip->mutex was lost after splitting
snd_usb_endpoint_set_params() and snd_usb_endpoint_prepare().
Apply the same mutex again to the former function.
We fixed the bug introduced by the patch for managing the shared
clocks at the commit 809f44a0cc5a ("ALSA: usb-audio: Clear fixed clock
rate at closing EP"), but it was merely a workaround. By this change,
the clock reference rate is cleared at each EP close, hence the still
remaining EP may need a re-setup of rate unnecessarily.
This patch introduces the proper refcounting for the clock reference
object so that the clock setup is done only when needed.
Fixes: 809f44a0cc5a ("ALSA: usb-audio: Clear fixed clock rate at closing EP") Fixes: c11117b634f4 ("ALSA: usb-audio: Refcount multiple accesses on the single clock") Link: https://lore.kernel.org/r/20220920181126.4912-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+") Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a second attempt to fix the bug appearing on Android with the
recent kernel; the first try was ff878b408a03 and reverted at commit 79764ec772bc.
The details taken from the v1 patch:
One of the former changes for the endpoint management was the more
consistent setup of endpoints at hw_params.
snd_usb_endpoint_configure() is a single function that does the full
setup, and it's called from both PCM hw_params and prepare callbacks.
Although the EP setup at the prepare phase is usually skipped (by
checking need_setup flag), it may be still effective in some cases
like suspend/resume that requires the interface setup again.
As it's a full and single setup, the invocation of
snd_usb_endpoint_configure() includes not only the USB interface setup
but also the buffer release and allocation. OTOH, doing the buffer
release and re-allocation at PCM prepare phase is rather superfluous,
and better to be done only in the hw_params phase.
For those optimizations, this patch splits the endpoint setup to two
phases: snd_usb_endpoint_set_params() and snd_usb_endpoint_prepare(),
to be called from hw_params and from prepare, respectively.
Note that this patch changes the driver operation slightly,
effectively moving the USB interface setup again to PCM prepare stage
instead of hw_params stage, while the buffer allocation and such
initializations are still done at hw_params stage.
And, the change of the USB interface setup timing (moving to prepare)
gave an interesting "fix", too: it was reported that the recent
kernels caused silent output at the beginning on playbacks on some
devices on Android, and this change casually fixed the regression.
It seems that those devices are picky about the sample rate change (or
the interface change?), and don't follow the too immediate rate
changes.
Meanwhile, Android operates the PCM in the following order:
- open, then hw_params with the possibly highest sample rate
- close without prepare
- re-open, hw_params with the normal sample rate
- prepare, and start streaming
This procedure ended up the hw_params twice with different rates, and
because the recent kernel did set up the sample rate twice one and
after, it screwed up the device. OTOH, the earlier kernels didn't set
up the USB interface at hw_params, hence this problem didn't appear.
Now, with this patch, the USB interface setup is again back to the
prepare phase, and it works around the problem automagically.
Although we should address the sample rate problem in a more solid
way in future, let's keep things working as before for now.
***
What's new in the take#2 patch:
- The regression caused by the v1 patch (bko#216500) was due to the
missing check of need_setup flag at hw_params. Now the check is
added, and the snd_usb_endpoint_set_params() call is skipped when
the running EP is re-opened.
- There was another bug in v1 where the clock reference rate wasn't
updated at hw_params phase, which may lead to a lack of the proper
hw constraints when an application doesn't issue the prepare but
only the hw_params call. This patch fixes it as well by tracking
the clock rate change in the prepare callback with a new flag
"need_update" for the clock reference object, just like others.
- The configure_endpoints() are simplified and folded back into
snd_usb_pcm_prepare().
The recent commit c11117b634f4 ("ALSA: usb-audio: Refcount multiple
accesses on the single clock") tries to manage the clock rate shared
by several endpoints. This was intended for avoiding the unmatched
rate by a different endpoint, but unfortunately, it introduced a
regression for PulseAudio and pipewire, too; those applications try to
probe the multiple possible rates (44.1k and 48kHz) and setting up the
normal rate fails but only the last rate is applied.
The cause is that the last sample rate is still left to the clock
reference even after closing the endpoint, and this value is still
used at the next open. It happens only when applications set up via
PCM prepare but don't start/stop the stream; the rate is reset when
the stream is stopped, but it's not cleared at close.
This patch addresses the issue above, simply by clearing the rate set
in the clock reference at the last close of each endpoint.
When a clock source is connected to multiple nodes / endpoints, the
current USB-audio driver tries to set up at each time one of them is
configured. Although it reads the current rate and updates only if it
differs, some devices seem unhappy with this behavior and spew the
errors when reading/updating the rate unnecessarily.
This patch tries to reduce the redundant clock setup by introducing a
refcount for each clock source. When the stream is actually running,
a clock rate is "locked", and it bypasses the clock and/or refuse to
change any longer.
There are mainly two reasons that thp_get_unmapped_area() should be
used for EROFS as other filesystems:
- It's needed to enable PMD mappings as a FSDAX filesystem, see
commit 74d2fad1334d ("thp, dax: add thp_get_unmapped_area for pmd
mappings");
- It's useful together with large folios and
CONFIG_READ_ONLY_THP_FOR_FS which enable THPs for mmapped files
(e.g. shared libraries) even without FSDAX. See commit 1854bc6e2420
("mm/readahead: Align file mappings for non-DAX").
Fixes: 06252e9ce05b ("erofs: dax support for non-tailpacking regular file") Fixes: ce529cc25b18 ("erofs: enable large folios for iomap mode") Fixes: e6687b89225e ("erofs: enable large folios for fscache mode") Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com> Link: https://lore.kernel.org/r/20240306053138.2240206-1-hsiangkao@linux.alibaba.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to abnormal data in skb->data, the extension bitmap length
exceeds 32 when decoding ras message then uses the length to make
a shift operation. It will change into negative after several loop.
UBSAN load could detect a negative shift as an undefined behaviour
and reports exception.
So we add the protection to avoid the length exceeding 32. Or else
it will return out of range error and stop decoding.
Fixes: 5e35941d9901 ("[NETFILTER]: Add H.323 conntrack/NAT helper") Signed-off-by: Lena Wang <lena.wang@mediatek.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If connection isn't established yet, get_mr() will fail, trigger connection after
get_mr().
Fixes: 584a8279a44a ("RDS: RDMA: return appropriate error on rdma map failures") Reported-and-tested-by: syzbot+d4faee732755bba9838e@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running an XDP program that is attached to a cpumap entry, we don't
initialise the xdp_rxq_info data structure being used in the xdp_buff
that backs the XDP program invocation. Tobias noticed that this leads to
random values being returned as the xdp_md->rx_queue_index value for XDP
programs running in a cpumap.
This means we're basically returning the contents of the uninitialised
memory, which is bad. Fix this by zero-initialising the rxq data
structure before running the XDP program.
Fixes: 9216477449f3 ("bpf: cpumap: Add the possibility to attach an eBPF program to cpumap") Reported-by: Tobias Böhm <tobias@aibor.de> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20240305213132.11955-1-toke@redhat.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The buggy address belongs to the object at ffff88809a07fc00
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 100 bytes inside of
freed 512-byte region [ffff88809a07fc00, ffff88809a07fe00)
Memory state around the buggy address: ffff88809a07fb00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88809a07fb80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88809a07fc00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88809a07fc80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88809a07fd00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 3b1137fe7482 ("net: ipv6: Change notifications for multipath add to RTA_MULTIPATH") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20240303144801.702646-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function ice_bridge_setlink() may encounter a NULL pointer dereference
if nlmsg_find_attr() returns NULL and br_spec is dereferenced subsequently
in nla_for_each_nested(). To address this issue, add a check to ensure that
br_spec is not NULL before proceeding with the nested attribute iteration.
Fixes: b1edc14a3fbf ("ice: Implement ice_bridge_getlink and ice_bridge_setlink") Signed-off-by: Rand Deeb <rand.sec96@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on the static analyzis of the code it looks like when an entry
from the MAC table was removed, the entry was still used after being
freed. More precise the vid of the mac_entry was used after calling
devm_kfree on the mac_entry.
The fix consists in first using the vid of the mac_entry to delete the
entry from the HW and after that to free it.
Issue is similar to the one I fixed in commit 8d975c15c0cd
("ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()")
We have to save skb->network_header in a temporary variable
in order to be able to recompute the network_header pointer
after a pskb_inet_may_pull() call.
pskb_inet_may_pull() makes sure the needed headers are in skb->head.
I'm updating __assign_str() and will be removing the second parameter. To
make sure that it does not break anything, I make sure that it matches the
__string() field, as that is where the string is actually going to be
saved in. To make sure there's nothing that breaks, I added a WARN_ON() to
make sure that what was used in __string() is the same that is used in
__assign_str().
In doing this change, an error was triggered as __assign_str() now expects
the string passed in to be a char * value. I instead had the following
warning:
include/trace/events/qdisc.h: In function ‘trace_event_raw_event_qdisc_reset’:
include/trace/events/qdisc.h:91:35: error: passing argument 1 of 'strcmp' from incompatible pointer type [-Werror=incompatible-pointer-types]
91 | __assign_str(dev, qdisc_dev(q));
That's because the qdisc_enqueue() and qdisc_reset() pass in qdisc_dev(q)
to __assign_str() and to __string(). But that function returns a pointer
to struct net_device and not a string.
It appears that these events are just saving the pointer as a string and
then reading it as a string as well.
Use qdisc_dev(q)->name to save the device instead.
Fixes: a34dac0b90552 ("net_sched: add tracepoints for qdisc_reset() and qdisc_destroy()") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disable NAPI before shutting down queues that this particular NAPI
contains so that the order of actions in i40e_queue_pair_disable()
mirrors what we do in i40e_queue_pair_enable().
Fixes: 123cecd427b6 ("i40e: added queue pair disable/enable functions") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently routines that are supposed to toggle state of ring pair do not
take care of associated interrupt with queue vector that these rings
belong to. This causes funky issues such as dead interface due to irq
misconfiguration, as per Pavel's report from Closes: tag.
Add a function responsible for disabling single IRQ in EIMC register and
call this as a very first thing when disabling ring pair during xsk_pool
setup. For enable let's reuse ixgbe_irq_enable_queues(). Besides this,
disable/enable NAPI as first/last thing when dealing with closing or
opening ring pair that xsk_pool is being configured on.
Reported-by: Pavel Vazharov <pavel@x3me.net> Closes: https://lore.kernel.org/netdev/CAJEV1ijxNyPTwASJER1bcZzS9nMoZJqfR86nu_3jFFVXzZQ4NA@mail.gmail.com/ Fixes: 024aa5800f32 ("ixgbe: added Rx/Tx ring disable/enable functions") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current driver has some asymmetry in the runtime PM calls. On lan78xx_open()
it will call usb_autopm_get() and unconditionally usb_autopm_put(). And
on lan78xx_stop() it will call only usb_autopm_put(). So far, it was
working only because this driver do not activate autosuspend by default,
so it was visible only by warning "Runtime PM usage count underflow!".
Since, with current driver, we can't use runtime PM with active link,
execute lan78xx_open()->usb_autopm_put() only in error case. Otherwise,
keep ref counting high as long as interface is open.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
DMA API debug brings to light leaking dma-mappings as dma_map_sg and
dma_unmap_sg are not correctly balanced.
If an error occurs in mmci_cmd_irq function, only mmci_dma_error
function is called and as this API is not managed on stm32 variant,
dma_unmap_sg is never called in this error path.
In SDIO mode, the sg list for requests can be unaligned with what the
STM32 SDMMC internal DMA can support. In that case, instead of failing,
use a temporary bounce buffer to copy from/to the sg list.
This buffer is limited to 1MB. But for that we need to also limit
max_req_size to 1MB. It has not shown any throughput penalties for
SD-cards or eMMC.
when MPTCP server accepts an incoming connection, it clones its listener
socket. However, the pointer to 'inet_opt' for the new socket has the same
value as the original one: as a consequence, on program exit it's possible
to observe the following splat:
BUG: KASAN: double-free in inet_sock_destruct+0x54f/0x8b0
Free of addr ffff888485950880 by task swapper/25/0
The buggy address belongs to the object at ffff888485950880
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes inside of
64-byte region [ffff888485950880, ffff8884859508c0)
Memory state around the buggy address: ffff888485950780: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888485950800: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888485950880: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^ ffff888485950900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888485950980: 00 00 00 00 00 01 fc fc fc fc fc fc fc fc fc fc
Something similar (a refcount underflow) happens with CALIPSO/IPv6. Fix
this by duplicating IP / IPv6 options after clone, so that
ip{,6}_sock_destruct() doesn't end up freeing the same memory area twice.
This reverts commit 284b4d93daee56dff3e10029ddf2e03227f50dbf.
When using TLS device offload and coming from tls_device_reencrypt()
flow, -EBADMSG error in tls_do_decryption() should not be counted
towards the TLSTlsDecryptError counter.
Move the counter increase back to the decrypt_internal() call site in
decrypt_skb_update().
This also fixes an issue where:
if (n_sgin < 1)
return -EBADMSG;
Errors in decrypt_internal() were not counted after the cited patch.
Fixes: 284b4d93daee ("tls: rx: move counting TlsDecryptErrors for sync") Cc: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When NIC takes care of crypto (or the record has already
been decrypted) we forget to update darg->async. ->async
is supposed to mean whether record is async capable on
input and whether record has been queued for async crypto
on output.
Reported-by: Gal Pressman <gal@nvidia.com> Fixes: 3547a1f9d988 ("tls: rx: use async as an in-out argument") Tested-by: Gal Pressman <gal@nvidia.com> Link: https://lore.kernel.org/r/20220425233309.344858-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the bpf_fib_lookup() helper by making it to return the source
IPv4/IPv6 address if the BPF_FIB_LOOKUP_SRC flag is set.
For example, the following snippet can be used to derive the desired
source IP address:
struct bpf_fib_lookup p = { .ipv4_dst = ip4->daddr };
ret = bpf_skb_fib_lookup(skb, p, sizeof(p),
BPF_FIB_LOOKUP_SRC | BPF_FIB_LOOKUP_SKIP_NEIGH);
if (ret != BPF_FIB_LKUP_RET_SUCCESS)
return TC_ACT_SHOT;
/* the p.ipv4_src now contains the source address */
The inability to derive the proper source address may cause malfunctions
in BPF-based dataplanes for hosts containing netdevs with more than one
routable IP address or for multi-homed hosts.
For example, Cilium implements packet masquerading in BPF. If an
egressing netdev to which the Cilium's BPF prog is attached has
multiple IP addresses, then only one [hardcoded] IP address can be used for
masquerading. This breaks connectivity if any other IP address should have
been selected instead, for example, when a public and private addresses
are attached to the same egress interface.
The change was tested with Cilium [1].
Nikolay Aleksandrov helped to figure out the IPv6 addr selection.
[1]: https://github.com/cilium/cilium/pull/28283
Signed-off-by: Martynas Pumputis <m@lambda.lt> Link: https://lore.kernel.org/r/20231007081415.33502-2-m@lambda.lt Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ability to specify routing table ID to the `bpf_fib_lookup` BPF
helper.
A new field `tbid` is added to `struct bpf_fib_lookup` used as
parameters to the `bpf_fib_lookup` BPF helper.
When the helper is called with the `BPF_FIB_LOOKUP_DIRECT` and
`BPF_FIB_LOOKUP_TBID` flags the `tbid` field in `struct bpf_fib_lookup`
will be used as the table ID for the fib lookup.
If the `tbid` does not exist the fib lookup will fail with
`BPF_FIB_LKUP_RET_NOT_FWDED`.
The `tbid` field becomes a union over the vlan related output fields
in `struct bpf_fib_lookup` and will be zeroed immediately after usage.
This functionality is useful in containerized environments.
For instance, if a CNI wants to dictate the next-hop for traffic leaving
a container it can create a container-specific routing table and perform
a fib lookup against this table in a "host-net-namespace-side" TC program.
This functionality also allows `ip rule` like functionality at the TC
layer, allowing an eBPF program to pick a routing table based on some
aspect of the sk_buff.
As a concrete use case, this feature will be used in Cilium's SRv6 L3VPN
datapath.
When egress traffic leaves a Pod an eBPF program attached by Cilium will
determine which VRF the egress traffic should target, and then perform a
FIB lookup in a specific table representing this VRF's FIB.
The bpf_fib_lookup() also looks up the neigh table.
This was done before bpf_redirect_neigh() was added.
In the use case that does not manage the neigh table
and requires bpf_fib_lookup() to lookup a fib to
decide if it needs to redirect or not, the bpf prog can
depend only on using bpf_redirect_neigh() to lookup the
neigh. It also keeps the neigh entries fresh and connected.
This patch adds a bpf_fib_lookup flag, SKIP_NEIGH, to avoid
the double neigh lookup when the bpf prog always call
bpf_redirect_neigh() to do the neigh lookup. The params->smac
output is skipped together when SKIP_NEIGH is set because
bpf_redirect_neigh() will figure out the smac also.
It is reported to cause boot crashes in Android systems, so revert it
from the stable trees for now.
Cc: Rob Clark <robdclark@chromium.org> Cc: Georgi Djakov <djakov@kernel.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
syzbot reported another task hung in __unix_gc(). [0]
The current while loop assumes that all of the left candidates
have oob_skb and calling kfree_skb(oob_skb) releases the remaining
candidates.
However, I missed a case that oob_skb has self-referencing fd and
another fd and the latter sk is placed before the former in the
candidate list. Then, the while loop never proceeds, resulting
the task hung.
__unix_gc() has the same loop just before purging the collected skb,
so we can call kfree_skb(oob_skb) there and let __skb_queue_purge()
release all inflight sockets.
The commit was applied to make further commits apply cleanly, but the
commit depends on other commits in the same patchset. I.e. the
controlling DSI host would need a change too. Thus one would need to
backport the full patchset changing the DSI hosts and all downstream
DSI device drivers.
Revert the commit and fix up the conflicts with the backported fixes
to the lt8912b driver.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring a hugetlb filesystem via the fsconfig() syscall, there is
a possible NULL dereference in hugetlbfs_fill_super() caused by assigning
NULL to ctx->hstate in hugetlbfs_parse_param() when the requested pagesize
is non valid.
Put the reference count of cache_cred in cachefiles_daemon_unbind() to
fix the problem. And also put cache_cred in cachefiles_add_cache() error
branch to avoid memory leaks.
Fixes: 9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem") CC: stable@vger.kernel.org Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240217081431.796809-1-libaokun1@huawei.com Acked-by: David Howells <dhowells@redhat.com> Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted by Eric we can break the lock dependency chain avoid
dumping any extended info for the mptcp subflow listener:
nothing actually useful is presented there.
Fixes: b8adb69a7d29 ("mptcp: fix lockless access in subflow ULP diag") Cc: stable@vger.kernel.org Reported-by: Eric Dumazet <edumazet@google.com> Closes: https://lore.kernel.org/netdev/CANn89iJ=Oecw6OZDwmSYc9HJKQ_G32uN11L+oUcMu+TOD5Xiaw@mail.gmail.com/ Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-9-162e87e48497@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when inserting not contiguous data in the subflow write queue,
the protocol creates a new skb and prevent the TCP stack from
merging it later with already queued skbs by setting the EOR marker.
Still no push flag is explicitly set at the end of previous GSO
packet, making the aggregation on the receiver side sub-optimal -
and packetdrill self-tests less predictable.
Explicitly mark the end of not contiguous DSS with the push flag.
Fixes: 6d0060f600ad ("mptcp: Write MPTCP DSS headers to outgoing data packets") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-4-162e87e48497@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msk socket uses to different timeout to track close related
events and retransmissions. The existing helpers do not indicate
clearly which timer they actually touch, making the related code
quite confusing.
Change the existing helpers name to avoid such confusion. No
functional change intended.
This patch is linked to the next one ("mptcp: fix dangling connection
hang-up"). The two patches are supposed to be backported together.
Cc: stable@vger.kernel.org # v5.11+ Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On incoming TCP reset, subflow closing could happen before error
propagation. That in turn could cause the socket error being ignored,
and a missing socket state transition, as reported by Daire-Byrne.
Address the issues explicitly checking for subflow socket error at
close time. To avoid code duplication, factor-out of __mptcp_error_report()
a new helper implementing the relevant bits.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/429 Fixes: 15cc10453398 ("mptcp: deliver ssk errors to msk") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MKTME repurposes the high bit of physical address to key id for encryption
key and, even though MAXPHYADDR in CPUID[0x80000008] remains the same,
the valid bits in the MTRR mask register are based on the reduced number
of physical address bits.
detect_tme() in arch/x86/kernel/cpu/intel.c detects TME and subtracts
it from the total usable physical bits, but it is called too late.
Move the call to early_init_intel() so that it is called in setup_arch(),
before MTRRs are setup.
This fixes boot on TDX-enabled systems, which until now only worked with
"disable_mtrr_cleanup". Without the patch, the values written to the
MTRRs mask registers were 52-bit wide (e.g. 0x000fffff_80000800) and
the writes failed; with the patch, the values are 46-bit wide, which
matches the reduced MAXPHYADDR that is shown in /proc/cpuinfo.
Reported-by: Zixi Chen <zixchen@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org Link: https://lore.kernel.org/all/20240131230902.1867092-3-pbonzini%40redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable the domain") Reported-by: Johan Hovold <johan@kernel.org> Closes: https://lore.kernel.org/linux-arm-msm/ZdMwZa98L23mu3u6@hovoldconsulting.com/ Cc: <stable@vger.kernel.org> Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240226-rpmhpd-enable-corner-fix-v1-1-68c004cec48c@quicinc.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time SD/mmc phy is initialized, at times, in some of
the attempts, phy fails to completes its initialization
which results into timeout error. Per the HW spec, it is
a pre-requisite to ensure a stable SD clock before a phy
initialization is attempted.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC") Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Elad Nachman <enachman@marvell.com> Link: https://lore.kernel.org/r/20240222200930.1277665-1-enachman@marvell.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AC5X spec says PHY init complete bit must be polled until zero.
We see cases in which timeout can take longer than the standard
calculation on AC5X, which is expected following the spec comment above.
According to the spec, we must wait as long as it takes for that bit to
toggle on AC5X.
Cap that with 100 delay loops so we won't get stuck forever.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC") Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Elad Nachman <enachman@marvell.com> Link: https://lore.kernel.org/r/20240222191714.1216470-3-enachman@marvell.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
Initialize the qDMA irqs after the registers are configured so that
interrupts that may have been pending from a primary kernel don't get
processed by the irq handler before it is ready to and cause panic with
the following trace:
The PTDMA driver sets DMA masks in two different places for the same
device inconsistently. First call is in pt_pci_probe(), where it uses
48bit mask. The second call is in pt_dmaengine_register(), where it
uses a 64bit mask. Using 64bit dma mask causes IO_PAGE_FAULT errors
on DMA transfers between main memory and other devices.
Without the extra call it works fine. Additionally the second call
doesn't check the return value so it can silently fail.
Remove the superfluous dma_set_mask() call and only use 48bit mask.
The SoC may hang on 16 byte unaligned read transactions by QDMA.
Unaligned read transactions initiated by QDMA may stall in the NOC
(Network On-Chip), causing a deadlock condition. Stalled transactions will
trigger completion timeouts in PCIe controller.
Workaround:
Enable prefetch by setting the source descriptor prefetchable bit
( SD[PF] = 1 ).
Implement this workaround.
Cc: stable@vger.kernel.org Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs") Signed-off-by: Peng Ma <peng.ma@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20240201215007.439503-1-Frank.Li@nxp.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a syzbot report that device name buffers passed to device
replace are not properly checked for string termination which could lead
to a read out of bounds in getname_kernel().
Add a helper that validates both source and target device name buffers.
For devid as the source initialize the buffer to empty string in case
something tries to read it later.
This was originally analyzed and fixed in a different way by Edward Adam
Davis (see links).
It's currently possible to change the mesh ID when the
interface isn't yet in mesh mode, at the same time as
changing it into mesh mode. This leads to an overwrite
of data in the wdev->u union for the interface type it
currently has, causing cfg80211_change_iface() to do
wrong things when switching.
We could probably allow setting an interface to mesh
while setting the mesh ID at the same time by doing a
different order of operations here, but realistically
there's no userspace that's going to do this, so just
disallow changes in iftype when setting mesh ID.
The local helper function to compare the given pair of cycle count
evaluates them. If the left value is less than the right value, the
function returns negative value.
If the safe cycle is less than the current cycle, it is the case of
cycle lost. However, it is not currently handled properly.
Since tomoyo_write_control() updates head->write_buf when write()
of long lines is requested, we need to fetch head->write_buf after
head->io_sem is held. Otherwise, concurrent write() requests can
cause use-after-free-write and double-free problems.
Reported-by: Sam Sun <samsun1006219@gmail.com> Closes: https://lkml.kernel.org/r/CAEkJfYNDspuGxYx5kym8Lvp--D36CMDUErg4rxfWFJuPbbji8g@mail.gmail.com Fixes: bd03a3e4c9a9 ("TOMOYO: Add policy namespace support.") Cc: <stable@vger.kernel.org> # Linux 3.1+ Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Offset vmemmap so that the first page of vmemmap will be mapped
to the first page of physical memory in order to ensure that
vmemmap’s bounds will be respected during
pfn_to_page()/page_to_pfn() operations.
The conversion macros will produce correct SV39/48/57 addresses
for every possible/valid DRAM_BASE inside the physical memory limits.
If a directory has a block with only ".__afsXXXX" files in it (from
uncompleted silly-rename), these .__afsXXXX files are skipped but without
advancing the file position in the dir_context. This leads to
afs_dir_iterate() repeating the block again and again.
Fix this by making the code that skips the .__afsXXXX file also manually
advance the file position.
Commit a5a923038d70 (fbdev: fbcon: Properly revert changes when
vc_resize() failed) started restoring old font data upon failure (of
vc_resize()). But it performs so only for user fonts. It means that the
"system"/internal fonts are not restored at all. So in result, the very
first call to fbcon_do_set_font() performs no restore at all upon
failing vc_resize().
This can be reproduced by Syzkaller to crash the system on the next
invocation of font_get(). It's rather hard to hit the allocation failure
in vc_resize() on the first font_set(), but not impossible. Esp. if
fault injection is used to aid the execution/failure. It was
demonstrated by Sirius:
BUG: unable to handle page fault for address: fffffffffffffff8
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD cb7b067 P4D cb7b067 PUD cb7d067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 8007 Comm: poc Not tainted 6.7.0-g9d1694dc91ce #20
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:fbcon_get_font+0x229/0x800 drivers/video/fbdev/core/fbcon.c:2286
Call Trace:
<TASK>
con_font_get drivers/tty/vt/vt.c:4558 [inline]
con_font_op+0x1fc/0xf20 drivers/tty/vt/vt.c:4673
vt_k_ioctl drivers/tty/vt/vt_ioctl.c:474 [inline]
vt_ioctl+0x632/0x2ec0 drivers/tty/vt/vt_ioctl.c:752
tty_ioctl+0x6f8/0x1570 drivers/tty/tty_io.c:2803
vfs_ioctl fs/ioctl.c:51 [inline]
...
So restore the font data in any case, not only for user fonts. Note the
later 'if' is now protected by 'old_userfont' and not 'old_data' as the
latter is always set now. (And it is supposed to be non-NULL. Otherwise
we would see the bug above again.)
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734f3 ("power: supply: bq27xxx: Fix I2C IRQ race on remove") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc-14 notices that the allocation with sizeof(void) on 32-bit architectures
is not enough for a 64-bit phys_addr_t:
drivers/firmware/efi/capsule-loader.c: In function 'efi_capsule_open':
drivers/firmware/efi/capsule-loader.c:295:24: error: allocation of insufficient size '4' for type 'phys_addr_t' {aka 'long long unsigned int'} with size '8' [-Werror=alloc-size]
295 | cap_info->phys = kzalloc(sizeof(void *), GFP_KERNEL);
| ^
With mixed sync/async decryption, or failures of crypto_aead_decrypt,
we increment decrypt_pending but we never do the corresponding
decrement since tls_decrypt_done will not be called. In this case, we
should decrement decrypt_pending immediately to avoid getting stuck.
For example, the prequeue prequeue test gets stuck with mixed
modes (one async decrypt + one sync decrypt).
Propagating EINPROGRESS thru multiple layers of functions is
error prone. Use darg->async as an in/out argument, like we
use darg->zc today. On input it tells the code if async is
allowed, on output if it took place.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
If crypto didn't always invoke our callback for async
we'd not be clearing skb->sk and would crash in the
skb core when freeing it. This if must be dead code.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
Move counting TlsDecryptErrors to tls_do_decryption()
where differences between sync and async crypto are
reconciled.
No functional changes, this code just always gave
me a pause.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
We track both if the last record was handled by async crypto
and how many records were async. This is not necessary. We
implicitly assume once crypto goes async it will stay that
way, otherwise we'd reorder records. So just track if we're
in async mode, the exact number of records is not necessary.
This change also forces us into "async" mode more consistently
in case crypto ever decided to interleave async and sync.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
cmsg can be filled in during rx_list processing or normal
receive. Consolidate the code.
We don't need to keep the boolean to track if the cmsg was
created. 0 is an invalid content type.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
We pass zc as a pointer to bool a few functions down as an in/out
argument. This is error prone since C will happily evalue a pointer
as a boolean (IOW forgetting *zc and writing zc leads to loss of
developer time..). Wrap the arguments into a structure.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
We plumb pointer to chunk all the way to the decryption method.
It's set to the length of the text when decrypt_skb_update()
returns.
I think the code is written this way because original TLS
implementation passed &chunk to zerocopy_from_iter() and this
was carried forward as the code gotten more complex, without
any refactoring.
The fix for peek() introduced a new variable - to_decrypt
which for all practical purposes is what chunk is going to
get set to. Spare ourselves the pointer passing, use to_decrypt.
Use this opportunity to clean things up a little further.
Note that chunk / to_decrypt was mostly needed for the async
path, since the sync path would access rxm->full_len (decryption
transforms full_len from record size to text size). Use the
right source of truth more explicitly.
We have three cases:
- async - it's TLS 1.2 only, so chunk == to_decrypt, but we
need the min() because to_decrypt is a whole record
and we don't want to underflow len. Note that we can't
handle partial record by falling back to sync as it
would introduce reordering against records in flight.
- zc - again, TLS 1.2 only for now, so chunk == to_decrypt,
we don't do zc if len < to_decrypt, no need to check again.
- normal - it already handles chunk > len, we can factor out the
assignment to rxm->full_len and share it with zc.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
sk is unused, remove it to make it clear the function
doesn't poke at the socket.
size_used is always 0 on input and @length on success.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of tls_device poking into internals of the message
return 1 from tls_device_decrypted() if the device handled
the decryption.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
Use early return and a jump label to remove two indentation levels.
No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: f7fa16d49837 ("tls: decrement decrypt_pending if no async completion will be called") Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
