If the USB configuration is not valid, then avoid checking for
bmAttributes to prevent null pointer deference.
Cc: stable <stable@kernel.org> Fixes: 40e89ff5750f ("usb: gadget: Set self-powered based on MaxPower and bmAttributes") Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250224085604.417327-1-prashanth.k@oss.qualcomm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdev->config might be NULL, so check it before dereferencing.
CC: stable <stable@kernel.org> Fixes: 40e89ff5750f ("usb: gadget: Set self-powered based on MaxPower and bmAttributes") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20250220120314.3614330-1-m.szyprowski@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the USB gadget will be set as bus-powered based solely
on whether its bMaxPower is greater than 100mA, but this may miss
devices that may legitimately draw less than 100mA but still want
to report as bus-powered. Similarly during suspend & resume, USB
gadget is incorrectly marked as bus/self powered without checking
the bmAttributes field. Fix these by configuring the USB gadget
as self or bus powered based on bmAttributes, and explicitly set
it as bus-powered if it draws more than 100mA.
During probe, the TCPC alert interrupts are getting masked to
avoid unwanted interrupts during chip setup: this is ok to do
but there is no unmasking happening at any later time, which
means that the chip will not raise any interrupt, essentially
making it not functional as, while internally it does perform
all of the intended functions, it won't signal anything to the
outside.
Still, increasing the timeout value, albeit being the most straightforward
solution, eliminates the problem: the initial PPM reset may take up to
~8000-10000ms on some Lenovo laptops. When it is reset after the above
period of time (or even if ucsi_reset_ppm() is not called overall), UCSI
works as expected.
Moreover, if the ucsi_acpi module is loaded/unloaded manually after the
system has booted, reading the CCI values and resetting the PPM works
perfectly, without any timeout. Thus it's only a boot-time issue.
The reason for this behavior is not clear but it may be the consequence
of some tricks that the firmware performs or be an actual firmware bug.
As a workaround, increase the timeout to avoid failing the UCSI
initialization prematurely.
Syzbot once again identified a flaw in usb endpoint checking, see [1].
This time the issue stems from a commit authored by me (2eabb655a968
("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")).
While using usb_find_common_endpoints() may usually be enough to
discard devices with wrong endpoints, in this case one needs more
than just finding and identifying the sufficient number of endpoints
of correct types - one needs to check the endpoint's address as well.
Since cxacru_bind() fills URBs with CXACRU_EP_CMD address in mind,
switch the endpoint verification approach to usb_check_XXX_endpoints()
instead to fix incomplete ep testing.
When performing continuous unbind/bind operations on the USB drivers
available on the Renesas RZ/G2L SoC, a kernel crash with the message
"Unable to handle kernel NULL pointer dereference at virtual address"
may occur. This issue points to the usbhsc_notify_hotplug() function.
Flush the delayed work to avoid its execution when driver resources are
unavailable.
When used on Huawei hisi platforms, Prolific Mass Storage Card Reader
which the VID:PID is in 067b:2731 might fail to enumerate at boot time
and doesn't work well with LPM enabled, combination quirks:
USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM
fixed the problems.
This commit was found responsible for issues with SD card recognition,
as users had to re-insert their cards in the readers and wait for a
while. As for some people the SD card was involved in the boot process
it also caused boot failures.
of_parse_phandle_with_fixed_args() requires its caller to
call into of_node_put() on the node pointer from the output
structure, but such a call is currently missing.
This patch follows commit 92191dd10730 ("net: ipv6: fix dst ref loops in
rpl, seg6 and ioam6 lwtunnels") and, on a second thought, the same patch
is also needed for ila (even though the config that triggered the issue
was pathological, but still, we don't want that to happen).
Fixes: 79ff2fc31e0f ("ila: Cache a route to translated address") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Justin Iurman <justin.iurman@uliege.be> Link: https://patch.msgid.link/20250304181039.35951-1-justin.iurman@uliege.be Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When I read through the TSO codes, I found out that we probably
miss initializing the tx_flags of last seg when TSO is turned
off, which means at the following points no more timestamp
(for this last one) will be generated. There are three flags
to be handled in this patch:
1. SKBTX_HW_TSTAMP
2. SKBTX_BPF
3. SKBTX_SCHED_TSTAMP
Note that SKBTX_BPF[1] was added in 6.14.0-rc2 by commit 6b98ec7e882af ("bpf: Add BPF_SOCK_OPS_TSTAMP_SCHED_CB callback")
and only belongs to net-next branch material for now. The common
issue of the above three flags can be fixed by this single patch.
This patch initializes the tx_flags to SKBTX_ANY_TSTAMP like what
the UDP GSO does to make the newly segmented last skb inherit the
tx_flags so that requested timestamp will be generated in each
certain layer, or else that last one has zero value of tx_flags
which leads to no timestamp at all.
Fixes: 4ed2d765dfacc ("net-timestamp: TCP timestamping") Signed-off-by: Jason Xing <kerneljasonxing@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot caught an "KMSAN: uninit-value" warning [1], which is caused by the
ppp driver not initializing a 2-byte header when using socket filter.
The following code can generate a PPP filter BPF program:
'''
struct bpf_program fp;
pcap_t *handle;
handle = pcap_open_dead(DLT_PPP_PPPD, 65535);
pcap_compile(handle, &fp, "ip and outbound", 0, 0);
bpf_dump(&fp, 1);
'''
Its output is:
'''
(000) ldh [2]
(001) jeq #0x21 jt 2 jf 5
(002) ldb [0]
(003) jeq #0x1 jt 4 jf 5
(004) ret #65535
(005) ret #0
'''
Wen can find similar code at the following link:
https://github.com/ppp-project/ppp/blob/master/pppd/options.c#L1680
The maintainer of this code repository is also the original maintainer
of the ppp driver.
As you can see the BPF program skips 2 bytes of data and then reads the
'Protocol' field to determine if it's an IP packet. Then it read the first
byte of the first 2 bytes to determine the direction.
The issue is that only the first byte indicating direction is initialized
in current ppp driver code while the second byte is not initialized.
For normal BPF programs generated by libpcap, uninitialized data won't be
used, so it's not a problem. However, for carefully crafted BPF programs,
such as those generated by syzkaller [2], which start reading from offset
0, the uninitialized data will be used and caught by KMSAN.
Partially revert commit b71724147e73 ("be2net: replace polling with
sleeping in the FW completion path") w.r.t mcc mutex it introduces and the
use of usleep_range. The be2net be_ndo_bridge_getlink() callback is
called with rcu_read_lock, so this code has been broken for a long time.
Both the mutex_lock and the usleep_range can cause the issue Ian Kumlien
reported[1]. The call path is:
be_ndo_bridge_getlink -> be_cmd_get_hsw_config -> be_mcc_notify_wait ->
be_mcc_wait_compl -> usleep_range()
Tested-by: Ian Kumlien <ian.kumlien@gmail.com> Fixes: b71724147e73 ("be2net: replace polling with sleeping in the FW completion path") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250227164129.1201164-1-razor@blackwall.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+da65c993ae113742a25f@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/67c020c0.050a0220.222324.0011.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The module parameter defines number of iso packets per one URB. User is
allowed to set any value to the parameter of type int, which can lead to
various kinds of weird and incorrect behavior like integer overflows,
truncations, etc. Number of packets should be a small non-negative number.
Since this parameter is read-only, its value can be validated on driver
probe.
Leading zero bits are sent on the bus before the temperature value is
transmitted. If any of these bits are high, the connection might be
unstable or there could be no AD7314 / ADT730x (or compatible) at all.
Return -EIO in that case.
I could not find a single table that has the values currently present in
the table, change it to the actual values that can be found in [1]/[2]
and [3] (page 15 column 2)
The `pmbus_identify()` function fails to correctly determine the number
of supported pages on PMBus devices. This occurs because `info->pages`
is implicitly zero-initialised, and `pmbus_set_page()` does not perform
writes to the page register if `info->pages` is not yet initialised.
Without this patch, `info->pages` is always set to the maximum after
scanning.
This patch initialises `info->pages` to `PMBUS_PAGES` before the probing
loop, enabling `pmbus_set_page()` writes to make it out onto the bus
correctly identifying the number of pages. `PMBUS_PAGES` seemed like a
reasonable non-zero number because that's the current result of the
identification process.
del_vqs() frees virtqueues, therefore cfv->vq_tx pointer should be checked
for NULL before calling it, not cfv->vdev. Also the current implementation
is redundant because the pointer cfv->vdev is dereferenced before it is
checked for NULL.
Fix this by checking cfv->vq_tx for NULL instead of cfv->vdev before
calling del_vqs().
Fixes: 0d2e1a2926b1 ("caif_virtio: Introduce caif over virtio") Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru> Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com> Link: https://patch.msgid.link/20250227184716.4715-1-v.shevtsov@mt-integration.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In __udp_gso_segment the skb destructor is removed before segmenting the
skb but the socket reference is kept as-is. This is an issue if the
original skb is later orphaned as we can hit the following bug:
The above can happen following a sequence of events when using
OpenVSwitch, when an OVS_ACTION_ATTR_USERSPACE action precedes an
OVS_ACTION_ATTR_OUTPUT action:
1. OVS_ACTION_ATTR_USERSPACE is handled (in do_execute_actions): the skb
goes through queue_gso_packets and then __udp_gso_segment, where its
destructor is removed.
2. The segments' data are copied and sent to userspace.
3. OVS_ACTION_ATTR_OUTPUT is handled (in do_execute_actions) and the
same original skb is sent to its path.
4. If it later hits skb_orphan, we hit the bug.
Fix this by also removing the reference to the socket in
__udp_gso_segment.
Fixes: ad405857b174 ("udp: better wmem accounting on gso") Signed-off-by: Antoine Tenart <atenart@kernel.org> Link: https://patch.msgid.link/20250226171352.258045-1-atenart@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The order in which queue->cmd and rcv_state are updated is crucial.
If these assignments are reordered by the compiler, the worker might not
get queued in nvmet_tcp_queue_response(), hanging the IO. to enforce the
the correct reordering, set rcv_state using smp_store_release().
Fixes: bdaf13279192 ("nvmet-tcp: fix a segmentation fault during io parsing error") Signed-off-by: Meir Elisha <meir.elisha@volumez.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The system can experience a random crash a few minutes after the driver is
removed. This issue occurs due to improper handling of memory freeing in
the ishtp_hid_remove() function.
The function currently frees the `driver_data` directly within the loop
that destroys the HID devices, which can lead to accessing freed memory.
Specifically, `hid_destroy_device()` uses `driver_data` when it calls
`hid_ishtp_set_feature()` to power off the sensor, so freeing
`driver_data` beforehand can result in accessing invalid memory.
This patch resolves the issue by storing the `driver_data` in a temporary
variable before calling `hid_destroy_device()`, and then freeing the
`driver_data` after the device is destroyed.
As reported by the kernel test robot, the following warning occurs:
>> drivers/hid/hid-google-hammer.c:261:36: warning: 'cbas_ec_acpi_ids' defined but not used [-Wunused-const-variable=]
261 | static const struct acpi_device_id cbas_ec_acpi_ids[] = {
| ^~~~~~~~~~~~~~~~
The 'cbas_ec_acpi_ids' array is only used when CONFIG_ACPI is enabled.
Wrapping its definition and 'MODULE_DEVICE_TABLE' in '#ifdef CONFIG_ACPI'
prevents a compiler warning when ACPI is disabled.
Fixes: eb1aac4c8744f75 ("HID: google: add support tablet mode switch for Whiskers") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202501201141.jctFH5eB-lkp@intel.com/ Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's no guarantee here that the file is always with a
NUL-termination, so reading the string may read beyond the
end of the TLV. If that's the last TLV in the file, it can
perhaps even read beyond the end of the file buffer.
Fix that by limiting the print format to the size of the
buffer we have.
Local variable compact_result created at:
__alloc_pages_slowpath+0x66/0x16c0 mm/page_alloc.c:4218
__alloc_frozen_pages_noprof+0xa4c/0xe00 mm/page_alloc.c:4752
The utf16_le_to_7bit function claims to, naively, convert a UTF-16
string to a 7-bit ASCII string. By naively, we mean that it:
* drops the first byte of every character in the original UTF-16 string
* checks if all characters are printable, and otherwise replaces them
by exclamation mark "!".
This means that theoretically, all characters outside the 7-bit ASCII
range should be replaced by another character. Examples:
* lower-case alpha (É’) 0x0252 becomes 0x52 (R)
* ligature OE (Å“) 0x0153 becomes 0x53 (S)
* hangul letter pieup (ã…‚) 0x3142 becomes 0x42 (B)
* upper-case gamma (Æ”) 0x0194 becomes 0x94 (not printable) so gets
replaced by "!"
The result of this conversion for the GPT partition name is passed to
user-space as PARTNAME via udev, which is confusing and feels questionable.
However, there is a flaw in the conversion function itself. By dropping
one byte of each character and using isprint() to check if the remaining
byte corresponds to a printable character, we do not actually guarantee
that the resulting character is 7-bit ASCII.
This happens because we pass 8-bit characters to isprint(), which
in the kernel returns 1 for many values > 0x7f - as defined in ctype.c.
This results in many values which should be replaced by "!" to be kept
as-is, despite not being valid 7-bit ASCII. Examples:
The test_monitor_call() inline assembly uses the xgr instruction, which
also modifies the condition code, to clear a register. However the clobber
list of the inline assembly does not specify that the condition code is
modified, which may lead to incorrect code generation.
Use the lhi instruction instead to clear the register without that the
condition code is modified. Furthermore this limits clearing to the lower
32 bits of val, since its type is int.
rio_add_net() calls device_register() and fails when device_register()
fails. Thus, put_device() should be used rather than kfree(). Add
"mport->net = NULL;" to avoid a use after free issue.
Link: https://lkml.kernel.org/r/20250227073409.3696854-1-haoxiang_li2024@163.com Fixes: e8de370188d0 ("rapidio: add mport char device driver") Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of rio_add_net() should be checked. If it fails,
put_device() should be called to free the memory and give up the reference
initialized in rio_add_net().
Link: https://lkml.kernel.org/r/20250227041131.3680761-1-haoxiang_li2024@163.com Fixes: e6b585ca6e81 ("rapidio: move net allocation into core code") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Dan Carpenter <dan.carpenter@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible to set both MONITOR_FLAG_COOK_FRAMES and MONITOR_FLAG_ACTIVE
flags simultaneously on the same monitor interface from the userspace. This
causes a sub-interface to be created with no IEEE80211_SDATA_IN_DRIVER bit
set because the monitor interface is in the cooked state and it takes
precedence over all other states. When the interface is then being deleted
the kernel calls WARN_ONCE() from check_sdata_in_driver() because of missing
that bit.
Fix this by rejecting MONITOR_FLAG_COOK_FRAMES if it is set along with
other flags.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Syzbot keeps reporting an issue [1] that occurs when erroneous symbols
sent from userspace get through into user_alpha2[] via
regulatory_hint_user() call. Such invalid regulatory hints should be
rejected.
While a sanity check from commit 47caf685a685 ("cfg80211: regulatory:
reject invalid hints") looks to be enough to deter these very cases,
there is a way to get around it due to 2 reasons.
1) The way isalpha() works, symbols other than latin lower and
upper letters may be used to determine a country/domain.
For instance, greek letters will also be considered upper/lower
letters and for such characters isalpha() will return true as well.
However, ISO-3166-1 alpha2 codes should only hold latin
characters.
2) While processing a user regulatory request, between
reg_process_hint_user() and regulatory_hint_user() there happens to
be a call to queue_regulatory_request() which modifies letters in
request->alpha2[] with toupper(). This works fine for latin symbols,
less so for weird letter characters from the second part of _ctype[].
Syzbot triggers a warning in is_user_regdom_saved() by first sending
over an unexpected non-latin letter that gets malformed by toupper()
into a character that ends up failing isalpha() check.
Prevent this by enhancing is_an_alpha2() to ensure that incoming
symbols are latin letters and nothing else.
CPUID leaf 0x2's one-byte TLB descriptors report the number of entries
for specific TLB types, among other properties.
Typically, each emitted descriptor implies the same number of entries
for its respective TLB type(s). An emitted 0x63 descriptor is an
exception: it implies 4 data TLB entries for 1GB pages and 32 data TLB
entries for 2MB or 4MB pages.
For the TLB descriptors parsing code, the entry count for 1GB pages is
encoded at the intel_tlb_table[] mapping, but the 2MB/4MB entry count is
totally ignored.
Update leaf 0x2's parsing logic 0x2 to account for 32 data TLB entries
for 2MB/4MB pages implied by the 0x63 descriptor.
Fixes: e0ba94f14f74 ("x86/tlb_info: get last level TLB entry number of CPU") Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: stable@kernel.org Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/20250304085152.51092-4-darwi@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPUID leaf 0x2 emits one-byte descriptors in its four output registers
EAX, EBX, ECX, and EDX. For these descriptors to be valid, the most
significant bit (MSB) of each register must be clear.
Leaf 0x2 parsing at intel.c only validated the MSBs of EAX, EBX, and
ECX, but left EDX unchecked.
Validate EDX's most-significant bit as well.
Fixes: e0ba94f14f74 ("x86/tlb_info: get last level TLB entry number of CPU") Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: stable@kernel.org Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/20250304085152.51092-3-darwi@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPUID leaf 0x2 emits one-byte descriptors in its four output registers
EAX, EBX, ECX, and EDX. For these descriptors to be valid, the most
significant bit (MSB) of each register must be clear.
The historical Git commit:
019361a20f016 ("- pre6: Intel: start to add Pentium IV specific stuff (128-byte cacheline etc)...")
introduced leaf 0x2 output parsing. It only validated the MSBs of EAX,
EBX, and ECX, but left EDX unchecked.
Validate EDX's most-significant bit.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: stable@vger.kernel.org Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/20250304085152.51092-2-darwi@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dell XPS 13 7390 with the Realtek ALC3271 codec experiences
persistent humming noise when the power_save mode is enabled.
This issue occurs when the codec enters power saving mode,
leading to unwanted noise from the speakers.
This patch adds the affected model (PCI ID 0x1028:0x0962) to the
power_save denylist to ensure power_save is disabled by default,
preventing power-off related noise issues.
Steps to Reproduce
1. Boot the system with `snd_hda_intel` loaded.
2. Verify that `power_save` mode is enabled:
```sh
cat /sys/module/snd_hda_intel/parameters/power_save
````
output: 10 (default power save timeout)
3. Wait for the power save timeout
4. Observe a persistent humming noise from the speakers
5. Disable `power_save` manually:
```sh
echo 0 | sudo tee /sys/module/snd_hda_intel/parameters/power_save
````
6. Confirm that the noise disappears immediately.
This issue has been observed on my system, and this patch
successfully eliminates the unwanted noise. If other users
experience similar issues, additional reports would be helpful.
Both new_device_store and delete_device_store touch module global
resources (e.g. gpio_aggregator_lock). To prevent race conditions with
module unload, a reference needs to be held.
Add try_module_get() in these handlers.
For new_device_store, this eliminates what appears to be the most dangerous
scenario: if an id is allocated from gpio_aggregator_idr but
platform_device_register has not yet been called or completed, a concurrent
module unload could fail to unregister/delete the device, leaving behind a
dangling platform device/GPIO forwarder. This can result in various issues.
The following simple reproducer demonstrates these problems:
#!/bin/bash
while :; do
# note: whether 'gpiochip0 0' exists or not does not matter.
echo 'gpiochip0 0' > /sys/bus/platform/drivers/gpio-aggregator/new_device
done &
while :; do
modprobe gpio-aggregator
modprobe -r gpio-aggregator
done &
wait
Starting with the following warning, several kinds of warnings will appear
and the system may become unstable:
This happens due to the malformed report items sent by the emulated device
which results in a report, that has no fields, being added to the report list.
Due to this appleir_input_configured() is never called, hidinput_connect()
fails which results in the HID_CLAIMED_INPUT flag is not being set. However,
it does not make appleir_probe() fail and lets the event callback to be
called without the associated input device.
Thus, add a check for the HID_CLAIMED_INPUT flag and leave the event hook
early if the driver didn't claim any input_dev for some reason. Moreover,
some other hid drivers accessing input_dev in their event callbacks do have
similar checks, too.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9a4a5574ce42 ("HID: appleir: add support for Apple ir devices") Cc: stable@vger.kernel.org Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out some DTs do depend on this behavior. Specifically, a
downstream Pixel 6 DT. Revert the change at least until we can decide if
the DT spec can be changed instead.
Currently, when validating the mokvar table, we (re)map the entire table
on each iteration of the loop, adding space as we discover new entries.
If the table grows over a certain size, this fails due to limitations of
early_memmap(), and we get a failure and traceback:
Mapping the entire structure isn't actually necessary, as we don't ever
need more than one entry header mapped at once.
Changes efi_mokvar_table_init() to only map each entry header, not the
entire table, when determining the table size. Since we're not mapping
any data past the variable name, it also changes the code to enforce
that each variable name is NUL terminated, rather than attempting to
verify it in place.
Cc: <stable@vger.kernel.org> Signed-off-by: Peter Jones <pjones@redhat.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There was a quirk added to add a workaround for a Sapphire
RX 5600 XT Pulse that didn't allow BAR resizing. However,
the quirk caused a regression with runtime pm on Dell laptops
using those chips, rather than narrowing the scope of the
resizing quirk, add a quirk to prevent amdgpu from resizing
the BAR on those Dell platforms unless runtime pm is disabled.
v2: update commit message, add runpm check
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1707 Fixes: 907830b0fc9e ("PCI: Add a REBAR size quirk for Sapphire RX 5600 XT Pulse") Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5235053f443cef4210606e5fb71f99b915a9723d) Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Some customer platforms do not enable mmconfig for various reasons,
such as bios bug, and therefore cannot access the GPU extend configuration
space through mmio.
When the system enters the d3cold state and resumes, the amdgpu driver
fails to resume because the extend configuration space registers of
GPU can't be restored. At this point, Usually we only see some failure
dmesg log printed by amdgpu driver, it is difficult to find the root
cause.
Therefor print a warnning message if the system can't access the
extended configuration space register when using large bar.
Signed-off-by: Ma Jun <Jun.Ma2@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 099bffc7cadf ("drm/amdgpu: disable BAR resize on Dell G5 SE") Signed-off-by: Sasha Levin <sashal@kernel.org>
In [1] it was reported that the acct(2) system call can be used to
trigger NULL deref in cases where it is set to write to a file that
triggers an internal lookup. This can e.g., happen when pointing acc(2)
to /sys/power/resume. At the point the where the write to this file
happens the calling task has already exited and called exit_fs(). A
lookup will thus trigger a NULL-deref when accessing current->fs.
Reorganize the code so that the the final write happens from the
workqueue but with the caller's credentials. This preserves the
(strange) permission model and has almost no regression risk.
Use rlimit() helper instead of manually writing whole chain from
task to rlimit value. See patch "posix-cpu-timers: Use dedicated
helper to access rlimit values".
Link: https://lkml.kernel.org/r/20210728030822.524789-1-yang.yang29@zte.com.cn Signed-off-by: Yang Yang <yang.yang29@zte.com.cn> Reported-by: Zeal Robot <zealci@zte.com.cn> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: sh_def@163.com <sh_def@163.com> Cc: Yang Yang <yang.yang29@zte.com.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 56d5f3eba3f5 ("acct: perform last write from workqueue") Signed-off-by: Sasha Levin <sashal@kernel.org>
If drop_monitor is built as a kernel module, syzkaller may have time
to send a netlink NET_DM_CMD_START message during the module loading.
This will call the net_dm_monitor_start() function that uses
a spinlock that has not yet been initialized.
To fix this, let's place resource initialization above the registration
of a generic netlink family.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with Syzkaller.
Fixes: 9a8afc8d3962 ("Network Drop Monitor: Adding drop monitor implementation & Netlink protocol") Cc: stable@vger.kernel.org Signed-off-by: Ilia Gavrilov <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20250213152054.2785669-1-Ilia.Gavrilov@infotecs.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Expected behaviour:
In case we reach scheduler's limit, pfifo_tail_enqueue() will drop a
packet in scheduler's queue and decrease scheduler's qlen by one.
Then, pfifo_tail_enqueue() enqueue new packet and increase
scheduler's qlen by one. Finally, pfifo_tail_enqueue() return
`NET_XMIT_CN` status code.
Weird behaviour:
In case we set `sch->limit == 0` and trigger pfifo_tail_enqueue() on a
scheduler that has no packet, the 'drop a packet' step will do nothing.
This means the scheduler's qlen still has value equal 0.
Then, we continue to enqueue new packet and increase scheduler's qlen by
one. In summary, we can leverage pfifo_tail_enqueue() to increase qlen by
one and return `NET_XMIT_CN` status code.
The problem is:
Let's say we have two qdiscs: Qdisc_A and Qdisc_B.
- Qdisc_A's type must have '->graft()' function to create parent/child relationship.
Let's say Qdisc_A's type is `hfsc`. Enqueue packet to this qdisc will trigger `hfsc_enqueue`.
- Qdisc_B's type is pfifo_head_drop. Enqueue packet to this qdisc will trigger `pfifo_tail_enqueue`.
- Qdisc_B is configured to have `sch->limit == 0`.
- Qdisc_A is configured to route the enqueued's packet to Qdisc_B.
Enqueue packet through Qdisc_A will lead to:
- hfsc_enqueue(Qdisc_A) -> pfifo_tail_enqueue(Qdisc_B)
- Qdisc_B->q.qlen += 1
- pfifo_tail_enqueue() return `NET_XMIT_CN`
- hfsc_enqueue() check for `NET_XMIT_SUCCESS` and see `NET_XMIT_CN` => hfsc_enqueue() don't increase qlen of Qdisc_A.
The whole process lead to a situation where Qdisc_A->q.qlen == 0 and Qdisc_B->q.qlen == 1.
Replace 'hfsc' with other type (for example: 'drr') still lead to the same problem.
This violate the design where parent's qlen should equal to the sum of its childrens'qlen.
Bug impact: This issue can be used for user->kernel privilege escalation when it is reachable.
Fixes: 57dbb2d83d10 ("sched: add head drop fifo queue") Reported-by: Quang Le <quanglex97@gmail.com> Signed-off-by: Quang Le <quanglex97@gmail.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Link: https://patch.msgid.link/20250204005841.223511-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel idle driver is preferred over the ACPI processor idle driver,
but fails to implement the work around for Core2 generation CPUs, where
the TSC stops in C2 and deeper C-states. This causes stalls and boot
delays, when the clocksource watchdog does not catch the unstable TSC
before the CPU goes deep idle for the first time.
The ACPI driver marks the TSC unstable when it detects that the CPU
supports C2 or deeper and the CPU does not have a non-stop TSC.
Add the equivivalent work around to the Intel idle driver to cure that.
Fixes: 18734958e9bf ("intel_idle: Use ACPI _CST for processor models without C-state tables") Reported-by: Fab Stz <fabstz-it@yahoo.fr> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Fab Stz <fabstz-it@yahoo.fr> Cc: All applicable <stable@vger.kernel.org> Closes: https://lore.kernel.org/all/10cf96aa-1276-4bd4-8966-c890377030c3@yahoo.fr Link: https://patch.msgid.link/87bjupfy7f.ffs@tglx Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David reported a warning observed while loop testing kexec jump:
Interrupts enabled after irqrouter_resume+0x0/0x50
WARNING: CPU: 0 PID: 560 at drivers/base/syscore.c:103 syscore_resume+0x18a/0x220
kernel_kexec+0xf6/0x180
__do_sys_reboot+0x206/0x250
do_syscall_64+0x95/0x180
The corresponding interrupt flag trace:
hardirqs last enabled at (15573): [<ffffffffa8281b8e>] __up_console_sem+0x7e/0x90
hardirqs last disabled at (15580): [<ffffffffa8281b73>] __up_console_sem+0x63/0x90
That means __up_console_sem() was invoked with interrupts enabled. Further
instrumentation revealed that in the interrupt disabled section of kexec
jump one of the syscore_suspend() callbacks woke up a task, which set the
NEED_RESCHED flag. A later callback in the resume path invoked
cond_resched() which in turn led to the invocation of the scheduler:
This is a long standing problem, which probably got more visible with
the recent printk changes. Something does a task wakeup and the
scheduler sets the NEED_RESCHED flag. cond_resched() sees it set and
invokes schedule() from a completely bogus context. The scheduler
enables interrupts after context switching, which causes the above
warning at the end.
Quite some of the code paths in syscore_suspend()/resume() can result in
triggering a wakeup with the exactly same consequences. They might not
have done so yet, but as they share a lot of code with normal operations
it's just a question of time.
The problem only affects the PREEMPT_NONE and PREEMPT_VOLUNTARY scheduling
models. Full preemption is not affected as cond_resched() is disabled and
the preemption check preemptible() takes the interrupt disabled flag into
account.
Cure the problem by adding a corresponding check into cond_resched().
Reported-by: David Woodhouse <dwmw@amazon.co.uk> Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Tested-by: David Woodhouse <dwmw@amazon.co.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@vger.kernel.org Closes: https://lore.kernel.org/all/7717fe2ac0ce5f0a2c43fdab8b11f4483d54a2a4.camel@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the kernel, there are architectures (x86, arm64) that perform
boot-time relocation (for KASLR) without relying on PIE codegen. In this
case, all const global objects are emitted into .rodata, including const
objects with fields that will be fixed up by the boot-time relocation
code. This implies that .rodata (and .text in some cases) need to be
writable at boot, but they will usually be mapped read-only as soon as
the boot completes.
When using PIE codegen, the compiler will emit const global objects into
.data.rel.ro rather than .rodata if the object contains fields that need
such fixups at boot-time. This permits the linker to annotate such
regions as requiring read-write access only at load time, but not at
execution time (in user space), while keeping .rodata truly const (in
user space, this is important for reducing the CoW footprint of dynamic
executables).
This distinction does not matter for the kernel, but it does imply that
const data will end up in writable memory if the .data.rel.ro sections
are not treated in a special way, as they will end up in the writable
.data segment by default.
Indeed the PM can try to send a RM_ADDR over a msk without acquiring
first the msk socket lock.
The bugged code-path comes from an early optimization: when there
are no subflows, the PM should (usually) not send RM_ADDR
notifications.
The above statement is incorrect, as without locks another process
could concurrent create a new subflow and cause the RM_ADDR generation.
Additionally the supposed optimization is not very effective even
performance-wise, as most mptcp sockets should have at least one
subflow: the MPC one.
Address the issue removing the buggy code path, the existing "slow-path"
will handle correctly even the edge case.
Fixes: b6c08380860b ("mptcp: remove addr and subflow in PM netlink") Cc: stable@vger.kernel.org Reported-by: syzbot+cd3ce3d03a3393ae9700@syzkaller.appspotmail.com Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/546 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250224-net-mptcp-misc-fixes-v1-1-f550f636b435@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In exynos5_usbdrd_{pipe3,utmi}_set_refclk(), the masks
PHYCLKRST_MPLL_MULTIPLIER_MASK and PHYCLKRST_SSC_REFCLKSEL_MASK are not
inverted when applied to the register values. Fix it.
Observed VBUS_OVERRIDE & ID_OVERRIDE might be programmed
with unexpected value prior to XUSB PADCTL driver, this
could also occur in virtualization scenario.
For example, UEFI firmware programs ID_OVERRIDE=GROUNDED to set
a type-c port to host mode and keeps the value to kernel.
If the type-c port is connected a usb host, below errors can be
observed right after usb host mode driver gets probed. The errors
would keep until usb role class driver detects the type-c port
as device mode and notifies usb device mode driver to set both
ID_OVERRIDE and VBUS_OVERRIDE to correct value by XUSB PADCTL
driver.
[ 173.765814] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[ 173.765837] usb usb3-port2: config error
Taking virtualization into account, asserting XUSB PADCTL
reset would break XUSB functions used by other guest OS,
hence only reset VBUS & ID OVERRIDE of the port in
utmi_phy_init.
Syzbot reports [1] a warning in usb_submit_urb() triggered by
inconsistencies between expected and actually present endpoints
in gl620a driver. Since genelink_bind() does not properly
verify whether specified eps are in fact provided by the device,
in this case, an artificially manufactured one, one may get a
mismatch.
Fix the issue by resorting to a usbnet utility function
usbnet_get_endpoints(), usually reserved for this very problem.
Check for endpoints and return early before proceeding further if
any are missing.
The customer reports that there is a soft lockup issue related to
the i2c driver. After checking, the i2c module was doing a tx transfer
and the bmc machine reboots in the middle of the i2c transaction, the i2c
module keeps the status without being reset.
Due to such an i2c module status, the i2c irq handler keeps getting
triggered since the i2c irq handler is registered in the kernel booting
process after the bmc machine is doing a warm rebooting.
The continuous triggering is stopped by the soft lockup watchdog timer.
Disable the interrupt enable bit in the i2c module before calling
devm_request_irq to fix this issue since the i2c relative status bit
is read-only.
Check whether denominator expression x * (x - 1) * 1000 mod {2^32, 2^64}
produce zero and skip stddev computation in that case.
For now don't care about rec->counter * rec->counter overflow because
rec->time * rec->time overflow will likely happen earlier.
Cc: stable@vger.kernel.org Cc: Wen Yang <wenyang@linux.alibaba.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Link: https://lore.kernel.org/20250206090156.1561783-1-kniv@yandex-team.ru Fixes: e31f7939c1c27 ("ftrace: Avoid potential division by zero in function profiler") Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I still have some Soekris net4826 in a Community Wireless Network I
volunteer with. These devices use an AMD SC1100 SoC. I am running
OpenWrt on them, which uses a patched kernel, that naturally has
evolved over time. I haven't updated the ones in the field in a
number of years (circa 2017), but have one in a test bed, where I have
intermittently tried out test builds.
A few years ago, I noticed some trouble, particularly when "warm
booting", that is, doing a reboot without removing power, and noticed
the device was hanging after the kernel message:
[ 0.081615] Working around Cyrix MediaGX virtual DMA bugs.
If I removed power and then restarted, it would boot fine, continuing
through the message above, thusly:
[ 0.081615] Working around Cyrix MediaGX virtual DMA bugs.
[ 0.090076] Enable Memory-Write-back mode on Cyrix/NSC processor.
[ 0.100000] Enable Memory access reorder on Cyrix/NSC processor.
[ 0.100070] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.110058] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.120037] CPU: NSC Geode(TM) Integrated Processor by National Semi (family: 0x5, model: 0x9, stepping: 0x1)
[...]
In order to continue using modern tools, like ssh, to interact with
the software on these old devices, I need modern builds of the OpenWrt
firmware on the devices. I confirmed that the warm boot hang was still
an issue in modern OpenWrt builds (currently using a patched linux
v6.6.65).
Last night, I decided it was time to get to the bottom of the warm
boot hang, and began bisecting. From preserved builds, I narrowed down
the bisection window from late February to late May 2019. During this
period, the OpenWrt builds were using 4.14.x. I was able to build
using period-correct Ubuntu 18.04.6. After a number of bisection
iterations, I identified a kernel bump from 4.14.112 to 4.14.113 as
the commit that introduced the warm boot hang.
So, I tried reverting just that kernel change on top of the breaking
OpenWrt commit, and my warm boot hang went away.
Presumably, the warm boot hang is due to some register not getting
cleared in the same way that a loss of power does. That is
approximately as much as I understand about the problem.
More poking/prodding and coaching from Jonas Gorski, it looks
like this test patch fixes the problem on my board: Tested against
v6.6.67 and v4.14.113.
Fixes: 18fb053f9b82 ("x86/cpu/cyrix: Use correct macros for Cyrix calls on Geode processors") Debugged-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/CAHP3WfOgs3Ms4Z+L9i0-iBOE21sdMk5erAiJurPjnrL9LSsgRA@mail.gmail.com Cc: Matthew Whitehead <tedheadster@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch mitigates the two-reallocations issue with rpl_iptunnel by
providing the dst_entry (in the cache) to the first call to
skb_cow_head(). As a result, the very first iteration would still
trigger two reallocations (i.e., empty cache), while next iterations
would only trigger a single reallocation.
Performance tests before/after applying this patch, which clearly shows
there is no impact (it even shows improvement):
- before: https://ibb.co/nQJhqwc
- after: https://ibb.co/4ZvW6wV
Signed-off-by: Justin Iurman <justin.iurman@uliege.be> Cc: Alexander Aring <aahringo@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 13e55fbaec17 ("net: ipv6: fix dst ref loop on input in rpl lwt") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add static inline dst_dev_overhead() function to include/net/dst.h. This
helper function is used by ioam6_iptunnel, rpl_iptunnel and
seg6_iptunnel to get the dev's overhead based on a cache entry
(dst_entry). If the cache is empty, the default and generic value
skb->mac_len is returned. Otherwise, LL_RESERVED_SPACE() over dst's dev
is returned.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be> Cc: Alexander Lobakin <aleksander.lobakin@intel.com> Cc: Vadim Fedorenko <vadim.fedorenko@linux.dev> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 13e55fbaec17 ("net: ipv6: fix dst ref loop on input in rpl lwt") Signed-off-by: Sasha Levin <sashal@kernel.org>
Recently a bug was discovered where the server had entered TCP_ESTABLISHED
state, but the upper layers were not notified.
The same 5-tuple packet may be processed by different CPUSs, so two
CPUs may receive different ack packets at the same time when the
state is TCP_NEW_SYN_RECV.
In that case, req->ts_recent in tcp_check_req may be changed concurrently,
which will probably cause the newsk's ts_recent to be incorrectly large.
So that tcp_validate_incoming will fail. At this point, newsk will not be
able to enter the TCP_ESTABLISHED.
The cpu2's skb or a newly received skb will call tcp_v4_do_rcv to get
the newsk into the TCP_ESTABLISHED state, but at this point it is no
longer possible to notify the upper layer application. A notification
mechanism could be added here, but the fix is more complex, so the
current fix is used.
In tcp_check_req, req->ts_recent is used to assign a value to
tcp_sk(child)->rx_opt.ts_recent, so removing the change in req->ts_recent
and changing tcp_sk(child)->rx_opt.ts_recent directly after owning the
req fixes this bug.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We found an issue when using bpf_redirect with ipvs NAT mode after
commit ff70202b2d1a ("dev_forward_skb: do not scrub skb mark within
the same name space"). Particularly, we use bpf_redirect to return
the skb directly back to the netif it comes from, i.e., xnet is
false in skb_scrub_packet(), and then ipvs_property is preserved
and SNAT is skipped in the rx path.
ipvs_property has been already cleared when netns is changed in
commit 2b5ec1a5f973 ("netfilter/ipvs: clear ipvs_property flag when
SKB net namespace changed"). This patch just clears it in spite of
netns.
Fixes: 2b5ec1a5f973 ("netfilter/ipvs: clear ipvs_property flag when SKB net namespace changed") Signed-off-by: Philo Lu <lulie@linux.alibaba.com> Acked-by: Julian Anastasov <ja@ssi.bg> Link: https://patch.msgid.link/20250222033518.126087-1-lulie@linux.alibaba.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ES8328 codec driver, which is also used for the ES8388 chip that
appears to have an identical register map, claims that the output can
either take the route from DAC->Mixer->Output or through DAC->Output
directly. To the best of what I could find, this is not true, and
creates problems.
Without DACCONTROL17 bit index 7 set for the left channel, as well as
DACCONTROL20 bit index 7 set for the right channel, I cannot get any
analog audio out on Left Out 2 and Right Out 2 respectively, despite the
DAPM routes claiming that this should be possible. Furthermore, the same
is the case for Left Out 1 and Right Out 1, showing that those two don't
have a direct route from DAC to output bypassing the mixer either.
Those control bits toggle whether the DACs are fed (stale bread?) into
their respective mixers. If one "unmutes" the mixer controls in
alsamixer, then sure, the audio output works, but if it doesn't work
without the mixer being fed the DAC input then evidently it's not a
direct output from the DAC.
ES8328/ES8388 are seemingly not alone in this. ES8323, which uses a
separate driver for what appears to be a very similar register map,
simply flips those two bits on in its probe function, and then pretends
there is no power management whatsoever for the individual controls.
Fair enough.
My theory as to why nobody has noticed this up to this point is that
everyone just assumes it's their fault when they had to unmute an
additional control in ALSA.
Fix this in the es8328 driver by removing the erroneous direct route,
then get rid of the playback switch controls and have those bits tied to
the mixer's widget instead, which until now had no register to play
with.
Stats calculations involve a RMW to add the stat update to the existing
value. This is currently not protected by any synchronization mechanism,
so data races are possible. Add a spinlock to protect the update. The
reader side could be protected using u64_stats, but we would still need
a spinlock for the update side anyway. And we always do an update
immediately before reading the stats anyway.
Fixes: 89e5785fc8a6 ("[PATCH] Atmel MACB ethernet driver") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Link: https://patch.msgid.link/20250220162950.95941-1-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 22600596b675 ("ipv4: give an IPv4 dev to blackhole_netdev")
IPv4 neighbors can be constructed on the blackhole net device, but they
are constructed with an output function (neigh_direct_output()) that
simply calls dev_queue_xmit(). The latter will transmit packets via
'skb->dev' which might not be the blackhole net device if dst_dev_put()
switched 'dst->dev' to the blackhole net device while another CPU was
using the dst entry in ip_output(), but after it already initialized
'skb->dev' from 'dst->dev'.
Fix by making sure that neighbors are constructed on top of the
blackhole net device with an output function that simply consumes the
packets, in a similar fashion to dst_discard_out() and
blackhole_netdev_xmit().
Fixes: 8d7017fd621d ("blackhole_netdev: use blackhole_netdev to invalidate dst entries") Fixes: 22600596b675 ("ipv4: give an IPv4 dev to blackhole_netdev") Reported-by: Florian Meister <fmei@sfs.com> Closes: https://lore.kernel.org/netdev/20250210084931.23a5c2e4@hermes.local/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250220072559.782296-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
L2CAP_ECRED_CONN_RSP needs to respond DCID in the same order received as
SCID but the order is reversed due to use of list_add which actually
prepend channels to the list so the response is reversed:
Also make sure the response don't include channels that are not on
BT_CONNECT2 since the chan->ident can be set to the same value as in the
following trace:
< ACL Data TX: Handle 16 flags 0x00 dlen 12
LE L2CAP: LE Flow Control Credit (0x16) ident 6 len 4
Source CID: 64
Credits: 1
...
> ACL Data RX: Handle 16 flags 0x02 dlen 18
LE L2CAP: Enhanced Credit Connection Request (0x17) ident 6 len 10
PSM: 39 (0x0027)
MTU: 517
MPS: 251
Credits: 255
Source CID: 70
< ACL Data TX: Handle 16 flags 0x00 dlen 20
LE L2CAP: Enhanced Credit Connection Response (0x18) ident 6 len 12
MTU: 517
MPS: 247
Credits: 3
Result: Connection successful (0x0000)
Destination CID: 64
Destination CID: 68
Closes: https://github.com/bluez/bluez/issues/1094 Fixes: 9aa9d9473f15 ("Bluetooth: L2CAP: Fix responding with wrong PDU type") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We fixed the UAF issue in USB MIDI code by canceling the pending work
at closing each MIDI output device in the commit below. However, this
assumed that it's the only one that is tied with the endpoint, and it
resulted in unexpected data truncations when multiple devices are
assigned to a single endpoint and opened simultaneously.
For addressing the unexpected MIDI message drops, simply replace
cancel_work_sync() with flush_work(). The drain callback should have
been already invoked before the close callback, hence the port->active
flag must be already cleared. So this just assures that the pending
work is finished before freeing the resources.
Fixes: 0125de38122f ("ALSA: usb-audio: Cancel pending work at closing a MIDI substream") Reported-and-tested-by: John Keeping <jkeeping@inmusicbrands.com> Closes: https://lore.kernel.org/20250217111647.3368132-1-jkeeping@inmusicbrands.com Link: https://patch.msgid.link/20250218114024.23125-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a warning about unused variables when building with W=1 and no procfs:
net/sunrpc/cache.c:1660:30: error: 'cache_flush_proc_ops' defined but not used [-Werror=unused-const-variable=]
1660 | static const struct proc_ops cache_flush_proc_ops = {
| ^~~~~~~~~~~~~~~~~~~~
net/sunrpc/cache.c:1622:30: error: 'content_proc_ops' defined but not used [-Werror=unused-const-variable=]
1622 | static const struct proc_ops content_proc_ops = {
| ^~~~~~~~~~~~~~~~
net/sunrpc/cache.c:1598:30: error: 'cache_channel_proc_ops' defined but not used [-Werror=unused-const-variable=]
1598 | static const struct proc_ops cache_channel_proc_ops = {
| ^~~~~~~~~~~~~~~~~~~~~~
These are used inside of an #ifdef, so replacing that with an
IS_ENABLED() check lets the compiler see how they are used while
still dropping them during dead code elimination.
Fixes: dbf847ecb631 ("knfsd: allow cache_register to return error on failure") Reviewed-by: Jeff Layton <jlayton@kernel.org> Acked-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When there is a failure during bind QP, the cleanup flow destroys the
counter regardless if it is the one that created it or not, which is
problematic since if it isn't the one that created it, that counter could
still be in use.
Fix that by destroying the counter only if it was created during this call.
Fixes: 45842fc627c7 ("IB/mlx5: Support statistic q counter configuration") Signed-off-by: Patrisious Haddad <phaddad@nvidia.com> Reviewed-by: Mark Zhang <markzhang@nvidia.com> Link: https://patch.msgid.link/25dfefddb0ebefa668c32e06a94d84e3216257cf.1740033937.git.leon@kernel.org Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a DCT QP is created on an active lag, it's dctc.port is assigned
in a round-robin way, which is from 1 to dev->lag_port. In this case
when querying this QP, we may get qp_attr.port_num > 2.
Fix this by setting qp->port when modifying a DCT QP, and read port_num
from qp->port instead of dctc.port when querying it.
In [1] the meaning of the synthetic IBPB flags has been redefined for a
better separation of concerns:
- ENTRY_IBPB -- issue IBPB on entry only
- IBPB_ON_VMEXIT -- issue IBPB on VM-Exit only
and the Retbleed mitigations have been updated to match this new
semantics.
Commit [2] was merged shortly before [1], and their interaction was not
handled properly. This resulted in IBPB not being triggered on VM-Exit
in all SRSO mitigation configs requesting an IBPB there.
Specifically, an IBPB on VM-Exit is triggered only when
X86_FEATURE_IBPB_ON_VMEXIT is set. However:
- X86_FEATURE_IBPB_ON_VMEXIT is not set for "spec_rstack_overflow=ibpb",
because before [1] having X86_FEATURE_ENTRY_IBPB was enough. Hence,
an IBPB is triggered on entry but the expected IBPB on VM-exit is
not.
- X86_FEATURE_IBPB_ON_VMEXIT is not set also when
"spec_rstack_overflow=ibpb-vmexit" if X86_FEATURE_ENTRY_IBPB is
already set.
That's because before [1] this was effectively redundant. Hence, e.g.
a "retbleed=ibpb spec_rstack_overflow=bpb-vmexit" config mistakenly
reports the machine still vulnerable to SRSO, despite an IBPB being
triggered both on entry and VM-Exit, because of the Retbleed selected
mitigation config.
- UNTRAIN_RET_VM won't still actually do anything unless
CONFIG_MITIGATION_IBPB_ENTRY is set.
For "spec_rstack_overflow=ibpb", enable IBPB on both entry and VM-Exit
and clear X86_FEATURE_RSB_VMEXIT which is made superfluous by
X86_FEATURE_IBPB_ON_VMEXIT. This effectively makes this mitigation
option similar to the one for 'retbleed=ibpb', thus re-order the code
for the RETBLEED_MITIGATION_IBPB option to be less confusing by having
all features enabling before the disabling of the not needed ones.
For "spec_rstack_overflow=ibpb-vmexit", guard this mitigation setting
with CONFIG_MITIGATION_IBPB_ENTRY to ensure UNTRAIN_RET_VM sequence is
effectively compiled in. Drop instead the CONFIG_MITIGATION_SRSO guard,
since none of the SRSO compile cruft is required in this configuration.
Also, check only that the required microcode is present to effectively
enabled the IBPB on VM-Exit.
Finally, update the KConfig description for CONFIG_MITIGATION_IBPB_ENTRY
to list also all SRSO config settings enabled by this guard.
Fixes: 864bcaa38ee4 ("x86/cpu/kvm: Provide UNTRAIN_RET_VM") [1] Fixes: d893832d0e1e ("x86/srso: Add IBPB on VMEXIT") [2] Reported-by: Yosry Ahmed <yosryahmed@google.com> Signed-off-by: Patrick Bellasi <derkling@google.com> Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_map_single is using physical/bus device (DMA) but dma_unmap_single
is using framework device(NAND controller), which is incorrect.
Fixed dma_unmap_single to use correct physical/bus device.
Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem") Cc: stable@vger.kernel.org Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OP-TEE supplicant is a user-space daemon and it's possible for it
be hung or crashed or killed in the middle of processing an OP-TEE
RPC call. It becomes more complicated when there is incorrect shutdown
ordering of the supplicant process vs the OP-TEE client application which
can eventually lead to system hang-up waiting for the closure of the
client application.
Allow the client process waiting in kernel for supplicant response to
be killed rather than indefinitely waiting in an unkillable state. Also,
a normal uninterruptible wait should not have resulted in the hung-task
watchdog getting triggered, but the endless loop would.
This fixes issues observed during system reboot/shutdown when supplicant
got hung for some reason or gets crashed/killed which lead to client
getting hung in an unkillable state. It in turn lead to system being in
hung up state requiring hard power off/on to recover.
The generic_map_lookup_batch currently returns EINTR if it fails with
ENOENT and retries several times on bpf_map_copy_value. The next batch
would start from the same location, presuming it's a transient issue.
This is incorrect if a map can actually have "holes", i.e.
"get_next_key" can return a key that does not point to a valid value. At
least the array of maps type may contain such holes legitly. Right now
these holes show up, generic batch lookup cannot proceed any more. It
will always fail with EINTR errors.
Rather, do not retry in generic_map_lookup_batch. If it finds a non
existing element, skip to the next key. This simple solution comes with
a price that transient errors may not be recovered, and the iteration
might cycle back to the first key under parallel deletion. For example,
Hou Tao <houtao@huaweicloud.com> pointed out a following scenario:
For LPM trie map:
(1) ->map_get_next_key(map, prev_key, key) returns a valid key
(2) bpf_map_copy_value() return -ENOMENT
It means the key must be deleted concurrently.
(3) goto next_key
It swaps the prev_key and key
(4) ->map_get_next_key(map, prev_key, key) again
prev_key points to a non-existing key, for LPM trie it will treat just
like prev_key=NULL case, the returned key will be duplicated.
With the retry logic, the iteration can continue to the key next to the
deleted one. But if we directly skip to the next key, the iteration loop
would restart from the first key for the lpm_trie type.
However, not all races may be recovered. For example, if current key is
deleted after instead of before bpf_map_copy_value, or if the prev_key
also gets deleted, then the loop will still restart from the first key
for lpm_tire anyway. For generic lookup it might be better to stay
simple, i.e. just skip to the next key. To guarantee that the output
keys are not duplicated, it is better to implement map type specific
batch operations, which can properly lock the trie and synchronize with
concurrent mutators.
Fixes: cb4d03ab499d ("bpf: Add generic support for lookup batch op") Closes: https://lore.kernel.org/bpf/Z6JXtA1M5jAZx8xD@debian.debian/ Signed-off-by: Yan Zhai <yan@cloudflare.com> Acked-by: Hou Tao <houtao1@huawei.com> Link: https://lore.kernel.org/r/85618439eea75930630685c467ccefeac0942e2b.1739171594.git.yan@cloudflare.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Size of variable sd_gain equals four bytes - DA9150_QIF_SD_GAIN_SIZE.
Size of variable shunt_val equals two bytes - DA9150_QIF_SHUNT_VAL_SIZE.
The expression sd_gain * shunt_val is currently being evaluated using
32-bit arithmetic. So during the multiplication an overflow may occur.
As the value of type 'u64' is used as storage for the eventual result, put
ULL variable at the first position of each expression in order to give the
compiler complete information about the proper arithmetic to use. According
to C99 the guaranteed width for a variable of type 'unsigned long long' >=
64 bits.
Remove the explicit cast to u64 as it is meaningless.
Just for the sake of consistency, perform the similar trick with another
expression concerning 'iavg'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a419b4fd9138 ("power: Add support for DA9150 Fuel-Gauge") Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru> Link: https://lore.kernel.org/r/20250130090030.53422-1-a.vatoropin@crpt.ru Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix how port range keys are handled in __skb_flow_bpf_to_target() by:
- Separating PORTS and PORTS_RANGE key handling
- Using correct key_ports_range structure for range keys
- Properly initializing both key types independently
This ensures port range information is correctly stored in its dedicated
structure rather than incorrectly using the regular ports key structure.
Fixes: 59fb9b62fb6c ("flow_dissector: Fix to use new variables for port ranges in bpf hook") Reported-by: Qiang Zhang <dtzq01@gmail.com> Closes: https://lore.kernel.org/netdev/CAPx+-5uvFxkhkz4=j_Xuwkezjn9U6kzKTD5jz4tZ9msSJ0fOJA@mail.gmail.com/ Cc: Yoshiki Komachi <komachi.yoshiki@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://patch.msgid.link/20250218043210.732959-4-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes a bug in TC flower filter where rules combining a
specific destination port with a source port range weren't working
correctly.
The specific case was when users tried to configure rules like:
tc filter add dev ens38 ingress protocol ip flower ip_proto udp \
dst_port 5000 src_port 2000-3000 action drop
The root cause was in the flow dissector code. While both
FLOW_DISSECTOR_KEY_PORTS and FLOW_DISSECTOR_KEY_PORTS_RANGE flags
were being set correctly in the classifier, the __skb_flow_dissect_ports()
function was only populating one of them: whichever came first in
the enum check. This meant that when the code needed both a specific
port and a port range, one of them would be left as 0, causing the
filter to not match packets as expected.
Fix it by removing the either/or logic and instead checking and
populating both key types independently when they're in use.
Fixes: 8ffb055beae5 ("cls_flower: Fix the behavior using port ranges with hw-offload") Reported-by: Qiang Zhang <dtzq01@gmail.com> Closes: https://lore.kernel.org/netdev/CAPx+-5uvFxkhkz4=j_Xuwkezjn9U6kzKTD5jz4tZ9msSJ0fOJA@mail.gmail.com/ Cc: Yoshiki Komachi <komachi.yoshiki@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20250218043210.732959-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As explained in the previous patch, iterating for_each_netdev() and
gn->geneve_list during ->exit_batch_rtnl() could trigger ->dellink()
twice for the same device.
If CONFIG_DEBUG_LIST is enabled, we will see a list_del() corruption
splat in the 2nd call of geneve_dellink().
Let's remove for_each_netdev() in geneve_destroy_tunnels() and delegate
that part to default_device_exit_batch().
projects / thirdparty / kernel / stable.git / log
