regmap_update_bits() can fail so check its return value in
wcd_gpio_direction_output() for consistency with the rest of the code
and propagate any errors.
Select PM_GENERIC_DOMAINS instead of depending on it to ensure
it is always enabled when TI_SCI_PM_DOMAINS is selected.
Since PM_GENERIC_DOMAINS is an implicit symbol, it can only be enabled
through 'select' and cannot be explicitly enabled in configuration.
This simplifies the dependency chain and prevents build issues
This driver calls enable_irq_wake() during probe() unconditionally, and
never issues the required corresponding disable_irq_wake() to disable
hardware interrupt wakeup signals.
Additionally, whether or not a device should wake-up the system is
meant to be a policy decision based on sysfs (.../power/wakeup) in the
first place.
Update the driver to use the standard approach to enable/disable IRQ
wake during the suspend/resume callbacks. This solves both issues
described above.
For the i.MX8X and i.MX8 family SoCs, when the Cortex-M core is powered
up and started by the Cortex-A core using the bootloader (e.g., via the
U-Boot bootaux command), both M-core and Linux run within the same SCFW
(System Controller Firmware) partition. With that, Linux has permission
to control the M-core.
But once the M-core is started by the bootloader, the SCFW automatically
enables its clock and sets the clock rate. If Linux later attempts to
enable the same clock via clk_prepare_enable(), the SCFW returns a
'LOCKED' error, as the clock is already configured by the SCFW. This
causes the probe function in imx_rproc.c to fail, leading to the M-core
power domain being shut down while the core is still running. This
results in a fault from the SCU (System Controller Unit) and triggers a
system reset.
To address this issue, ignore handling the clk for i.MX8X and i.MX8
M-core, as SCFW already takes care of enabling and configuring the
clock.
If a synchronous error is detected as a result of user-space process
triggering a 2-bit uncorrected error, the CPU will take a synchronous
error exception such as Synchronous External Abort (SEA) on Arm64. The
kernel will queue a memory_failure() work which poisons the related
page, unmaps the page, and then sends a SIGBUS to the process, so that
a system wide panic can be avoided.
However, no memory_failure() work will be queued when abnormal
synchronous errors occur. These errors can include situations like
invalid PA, unexpected severity, no memory failure config support,
invalid GUID section, etc. In such a case, the user-space process will
trigger SEA again. This loop can potentially exceed the platform
firmware threshold or even trigger a kernel hard lockup, leading to a
system reboot.
Fix it by performing a force kill if no memory_failure() work is queued
for synchronous errors.
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com> Reviewed-by: Jane Chu <jane.chu@oracle.com> Reviewed-by: Hanjun Guo <guohanjun@huawei.com> Link: https://patch.msgid.link/20250714114212.31660-2-xueshuai@linux.alibaba.com
[ rjw: Changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed as well.
When that flag is set don't show messages in the cleanup path for
marking the controller dead.
There is a subtle contradiction between sections of the xHCI 1.2 spec
regarding the initialization of Input Endpoint Context fields. Section
4.8.2 ("Endpoint Context Initialization") states that all fields should
be initialized to 0. However, Section 6.2.3 ("Endpoint Context", p.453)
specifies that the Average TRB Length (avg_trb_len) field shall be
greater than 0, and explicitly notes (p.454): "Software shall set
Average TRB Length to '8' for control endpoints."
Strictly setting all fields to 0 during initialization conflicts with
the specific recommendation for control endpoints. In practice, setting
avg_trb_len = 0 is not meaningful for the hardware/firmware, as the
value is used for bandwidth calculation.
Motivation: Our company is developing a custom Virtual xHC hardware
platform that strictly follows the xHCI spec and its recommendations.
During validation, we observed that enumeration fails and a parameter
error (TRB Completion Code = 5) is reported if avg_trb_len for EP0 is
not set to 8 as recommended by Section 6.2.3. This demonstrates the
importance of assigning a meaningful, non-zero value to avg_trb_len,
even in virtualized or emulated environments.
This patch explicitly sets avg_trb_len to 8 for EP0 in
xhci_setup_addressable_virt_dev(), as recommended in Section 6.2.3, to
prevent potential issues with xHCI host controllers that enforce the
spec strictly.
When a USB4 dock is unplugged from a system it won't respond to ring
events. The PCI core handles the surprise removal event and notifies
all PCI drivers. The XHCI PCI driver sets a flag that the device is
being removed, and when the device stops responding a flag is also
added to indicate it's dying.
When that flag is set don't bother to show warnings about a missing
controller.
ucsi_psy_get_current_max would return 0mA as the maximum current if
UCSI detected a BC or a Default USB Power sporce.
The comment in this function is true that we can't tell the difference
between DCP/CDP or SDP chargers, but we can guarantee that at least 1-unit
of USB 1.1/2.0 power is available, which is 100mA, which is a better
fallback value than 0, which causes some userspaces, including the ChromeOS
power manager, to regard this as a power source that is not providing
any power.
In reality, 100mA is guaranteed from all sources in these classes.
The kernel does not provide sys_futex() on 32-bit architectures that do not
support 32-bit time representations, such as riscv32.
As a result, glibc cannot define SYS_futex, causing compilation failures in
tests that rely on this syscall. Define SYS_futex as SYS_futex_time64 in
such cases to ensure successful compilation and compatibility.
Signed-off-by: Cynthia Huang <cynthia@andestech.com> Signed-off-by: Ben Zong-You Xie <ben717@andestech.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Link: https://lore.kernel.org/all/20250710103630.3156130-1-ben717@andestech.com Signed-off-by: Sasha Levin <sashal@kernel.org>
AMU counters on certain CPPC-based platforms tend to yield inaccurate
delivered performance measurements on systems that are idle/mostly idle.
This results in an inaccurate frequency being stored by cpufreq in its
policy structure when the CPU is brought online. [1]
Consequently, if the userspace governor tries to set the frequency to a
new value, there is a possibility that it would be the erroneous value
stored earlier. In such a scenario, cpufreq would assume that the
requested frequency has already been set and return early, resulting in
the correct/new frequency request never making it to the hardware.
Since the operating frequency is liable to this sort of inconsistency,
mark the CPPC driver with CPUFREQ_NEED_UPDATE_LIMITS so that it is always
invoked when a target frequency update is requested.
The Lenovo Yoga 6 13ACL6 82ND has a similar BIOS problem as other Lenovo
laptops from that vintage that causes a rather long resume from suspend.
Add it to the quirk list that manipulates the scratch register to avoid
the issue.
Reported-by: Adam Berglund <adam.f.berglund@hotmail.com> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4434 Tested-by: Adam Berglund <adam.f.berglund@hotmail.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Hans de Goede <hansg@kernel.org> Link: https://lore.kernel.org/r/20250718172307.1928744-1-superm1@kernel.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When encounters some errors like these:
xhci_hcd 0000:4a:00.2: xHCI dying or halted, can't queue_command
xhci_hcd 0000:4a:00.2: FIXME: allocate a command ring segment
usb usb5-port6: couldn't allocate usb_device
It's hard to know whether xhc_state is dying or halted. So it's better
to print xhc_state's value which can help locate the resaon of the bug.
If a lookup in tracefs is done on a file that does not exist, it leaves a
dentry hanging around until memory pressure removes it. But eventfs
dentries should hang around as when their ref count goes to zero, it
requires more work to recreate it. For the rest of the tracefs dentries,
they hang around as their dentry is used as a descriptor for the tracing
system. But if a file lookup happens for a file in tracefs that does not
exist, it should be deleted.
Add a .d_delete callback that checks if dentry->fsdata is set or not. Only
eventfs dentries set fsdata so if it has content it should not be deleted
and should hang around in the cache.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
incidentally, securityfs_recursive_remove() is broken without that -
it leaks dentries, since simple_recursive_removal() does not expect
anything of that sort. It could be worked around by dput() in
remove_one() callback, but it's easier to just drop that double-get
stuff.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We used to need securityfs_remove() to undo simple_pin_fs() done when
the file had been created and to drop the second extra reference
taken at the same time. Now that neither is needed (or done by
securityfs_remove()), we can simply call simple_unlink() and be done
with that - the broken games with locking had been there only for the
sake of securityfs_remove().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, ext2_fiemap would unconditionally apply "len = min_t(u64, len,
i_size_read(inode));", When inode->i_size was 0 (for an empty file), this
would reduce the requested len to 0. Passing len = 0 to iomap_fiemap could
then result in an -EINVAL error, even for valid queries on empty files.
Similar to commit 1ed95281c0c7 ("anon_inode: raise SB_I_NODEV and SB_I_NOEXEC"):
it shouldn't be possible to execute pidfds via
execveat(fd_anon_inode, "", NULL, NULL, AT_EMPTY_PATH)
so raise SB_I_NOEXEC so that no one gets any creative ideas.
Also raise SB_I_NODEV as we don't expect or support any devices on pidfs.
Modify ata_scsi_lpm_store() to return an error if a user attempts to set
a link power management policy for a port that does not support LPM,
that is, ports flagged with ATA_FLAG_NO_LPM.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Link: https://lore.kernel.org/r/20250701125321.69496-6-dlemoal@kernel.org Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The AHCI specification version 1.3.1 section 8.3.1.4 (Software
Requirements and Precedence) states that:
If CAP.SSC or CAP.PSC is cleared to ‘0’, software should disable
device-initiated power management by issuing the appropriate SET
FEATURES command to the device.
To satisfy this constraint and force ata_dev_configure to disable the
device DIPM feature, modify ahci_update_initial_lpm_policy() to set the
ATA_FLAG_NO_DIPM flag on ports that have a host with either the
ATA_HOST_NO_PART flag set or the ATA_HOST_NO_SSC flag set.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.de.> Link: https://lore.kernel.org/r/20250701125321.69496-7-dlemoal@kernel.org Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit fa997b0576c9 ("ata: ahci: Do not enable LPM if no LPM states are
supported by the HBA") introduced an early return in
ahci_update_initial_lpm_policy() to ensure that the target_lpm_policy
of ports belonging to a host that does not support the Partial, Slumber
and DevSleep power states is unchanged and remains set to
ATA_LPM_UNKNOWN and thus prevents the execution of
ata_eh_link_set_lpm().
However, a user or a system daemon (e.g. systemd-udevd) may still
attempt changing the LPM policy through the sysfs
link_power_management_policy of the host.
Improve this to prevent sysfs LPM policy changes by setting the flag
ATA_FLAG_NO_LPM for the port of such host, and initialize the port
target_lpm_policy to ATA_LPM_MAX_POWER to guarantee that no unsupported
low power state is being used on the port and its link.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Niklas Cassel <cassel@kernel.org> Link: https://lore.kernel.org/r/20250701125321.69496-9-dlemoal@kernel.org Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We want a class that nests outside of I_MUTEX_NORMAL (for the sake of
callbacks that might want to lock the victim) and inside I_MUTEX_PARENT
(so that a variant of that could be used with parent of the victim
held locked by the caller).
In reality, simple_recursive_removal()
* never holds two locks at once
* holds the lock on parent of dentry passed to callback
* is used only on the trees with fixed topology, so the depths
are not changing.
So the locking order is actually fine.
AFAICS, the best solution is to assign I_MUTEX_CHILD to the locks
grabbed by that thing.
Reported-by: syzbot+169de184e9defe7fe709@syzkaller.appspotmail.com Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
generic/001 32s ... _check_generic_filesystem: filesystem on /dev/loop50 is inconsistent
(see /home/slavad/XFSTESTS-2/xfstests-dev/results//generic/001.full for details)
Ran: generic/001
Failures: generic/001
Failed 1 of 1 tests
fsck.hfs -d -n ./test-image.bin
** ./test-image.bin (NO WRITE)
Using cacheBlockSize=32K cacheTotalBlock=1024 cacheSize=32768K.
Executing fsck_hfs (version 540.1-Linux).
** Checking HFS volume.
The volume name is untitled
** Checking extents overflow file.
** Checking catalog file.
Unused node is not erased (node = 2)
Unused node is not erased (node = 4)
<skipped>
Unused node is not erased (node = 253)
Unused node is not erased (node = 254)
Unused node is not erased (node = 255)
Unused node is not erased (node = 256)
** Checking catalog hierarchy.
** Checking volume bitmap.
** Checking volume information.
Verify Status: VIStat = 0x0000, ABTStat = 0x0000 EBTStat = 0x0000
CBTStat = 0x0004 CatStat = 0x00000000
** The volume untitled was found corrupt and needs to be repaired.
volume type is HFS
primary MDB is at block 2 0x02
alternate MDB is at block 20971518 0x13ffffe
primary VHB is at block 0 0x00
alternate VHB is at block 0 0x00
sector size = 512 0x200
VolumeObject flags = 0x19
total sectors for volume = 20971520 0x1400000
total sectors for embedded volume = 0 0x00
This patch adds logic of clearing the deleted b-tree node.
With `two-primaries` enabled, DRBD tries to detect "concurrent" writes
and handle write conflicts, so that even if you write to the same sector
simultaneously on both nodes, they end up with the identical data once
the writes are completed.
In handling "superseeded" writes, we forgot a kref_get,
resulting in a premature drbd_destroy_device and use after free,
and further to kernel crashes with symptoms.
Relevance: No one should use DRBD as a random data generator, and apparently
all users of "two-primaries" handle concurrent writes correctly on layer up.
That is cluster file systems use some distributed lock manager,
and live migration in virtualization environments stops writes on one node
before starting writes on the other node.
Which means that other than for "test cases",
this code path is never taken in real life.
FYI, in DRBD 9, things are handled differently nowadays. We still detect
"write conflicts", but no longer try to be smart about them.
We decided to disconnect hard instead: upper layers must not submit concurrent
writes. If they do, that's their fault.
Signed-off-by: Sarah Newman <srn@prgmr.com> Signed-off-by: Lars Ellenberg <lars@linbit.com> Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> Link: https://lore.kernel.org/r/20250627095728.800688-1-christoph.boehmwalder@linbit.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Verify that number of partition maps isn't insanely high which can lead
to large allocation in udf_sb_alloc_partition_maps(). All partition maps
have to fit in the LVD which is in a single block.
Reported-by: syzbot+478f2c1a6f0f447a46bb@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot came up with a reproducer where a loop device block size is
changed underneath a mounted filesystem. This causes a mismatch between
the block device block size and the block size stored in the superblock
causing confusion in various places such as fs/buffer.c. The particular
issue triggered by syzbot was a warning in __getblk_slow() due to
requested buffer size not matching block device block size.
Fix the problem by getting exclusive hold of the loop device to change
its block size. This fails if somebody (such as filesystem) has already
an exclusive ownership of the block device and thus prevents modifying
the loop device under some exclusive owner which doesn't expect it.
Reported-by: syzbot+01ef7a8da81a975e1ccd@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Tested-by: syzbot+01ef7a8da81a975e1ccd@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20250711163202.19623-2-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clears up the warning added in 7ee3647243e5 ("migrate: Remove call to
->writepage") that occurs in various xfstests, causing "something found
in dmesg" failures.
[ 341.136573] gfs2_meta_aops does not implement migrate_folio
[ 341.136953] WARNING: CPU: 1 PID: 36 at mm/migrate.c:944 move_to_new_folio+0x2f8/0x300
Signed-off-by: Andrew Price <anprice@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A fuzzer test introduced corruption that ends up with a depth of 0 in
dir_e_read(), causing an undefined shift by 32 at:
index = hash >> (32 - dip->i_depth);
As calculated in an open-coded way in dir_make_exhash(), the minimum
depth for an exhash directory is ilog2(sdp->sd_hash_ptrs) and 0 is
invalid as sdp->sd_hash_ptrs is fixed as sdp->bsize / 16 at mount time.
So we can avoid the undefined behaviour by checking for depth values
lower than the minimum in gfs2_dinode_in(). Values greater than the
maximum are already being checked for there.
Also switch the calculation in dir_make_exhash() to use ilog2() to
clarify how the depth is calculated.
Tested with the syzkaller repro.c and xfstests '-g quick'.
Reported-by: syzbot+4708579bb230a0582a57@syzkaller.appspotmail.com Signed-off-by: Andrew Price <anprice@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Update the nvme_tcp_start_tls() function to use dev_err() instead of
dev_dbg() when a TLS error is detected. This ensures that handshake
failures are visible by default, aiding in debugging.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Laurence Oberman <loberman@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Same as done for raid0, set chunk_sectors limit to appropriately set the
atomic write size limit.
Setting chunk_sectors limit in this way overrides the stacked limit
already calculated based on the bottom device limits. This is ok, as
when any bios are sent to the bottom devices, the block layer will still
respect the bottom device chunk_sectors.
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com> Reviewed-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20250711105258.3135198-6-john.g.garry@oracle.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
NVMe devices from multiple vendors appear to get stuck in a reset state
that we can't get out of with an NVMe level Controller Reset. The kernel
would report these with messages that look like:
Device not ready; aborting reset, CSTS=0x1
These have historically required a power cycle to make them usable
again, but in many cases, a PCIe FLR is sufficient to restart operation
without a power cycle. Try it if the initial controller reset fails
during any nvme reset attempt.
Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If smb2_create_link() is called with ReplaceIfExists set and the name
does exist then a deadlock will happen.
ksmbd_vfs_kern_path_locked() will return with success and the parent
directory will be locked. ksmbd_vfs_remove_file() will then remove the
file. ksmbd_vfs_link() will then be called while the parent is still
locked. It will try to lock the same parent and will deadlock.
This patch moves the ksmbd_vfs_kern_path_unlock() call to *before*
ksmbd_vfs_link() and then simplifies the code, removing the file_present
flag variable.
Signed-off-by: NeilBrown <neil@brown.name> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Linux IMA (Integrity Measurement Architecture) subsystem used for
secure boot, file integrity, or remote attestation cannot be a loadable
module for few reasons listed below:
o Boot-Time Integrity: IMA’s main role is to measure and appraise files
before they are used. This includes measuring critical system files during
early boot (e.g., init, init scripts, login binaries). If IMA were a
module, it would be loaded too late to cover those.
o TPM Dependency: IMA integrates tightly with the TPM to record
measurements into PCRs. The TPM must be initialized early (ideally before
init_ima()), which aligns with IMA being built-in.
o Security Model: IMA is part of a Trusted Computing Base (TCB). Making it
a module would weaken the security model, as a potentially compromised
system could delay or tamper with its initialization.
IMA must be built-in to ensure it starts measuring from the earliest
possible point in boot which inturn implies TPM must be initialised and
ready to use before IMA.
To enable integration of tpm_event_log with the IMA subsystem, the TPM
drivers (tpm_crb and tpm_crb_ffa) also needs to be built-in. However with
FF-A driver also being initialised at device initcall level, it can lead to
an initialization order issue where:
- crb_acpi_driver_init() may run before tpm_crb_ffa_driver()_init and
ffa_init()
- As a result, probing the TPM device via CRB over FFA is deferred
- ima_init() (called as a late initcall) runs before deferred probe
completes, IMA fails to find the TPM and logs the below error:
| ima: No TPM chip found, activating TPM-bypass!
Eventually it fails to generate boot_aggregate with PCR values.
Because of the above stated dependency, the ffa driver needs to initialised
before tpm_crb_ffa module to ensure IMA finds the TPM successfully when
present.
[ jarkko: reformatted some of the paragraphs because they were going past
the 75 character boundary. ]
GCC appears to have kind of fragile inlining heuristics, in the
sense that it can change whether or not it inlines something based on
optimizations. It looks like the kcov instrumentation being added (or in
this case, removed) from a function changes the optimization results,
and some functions marked "inline" are _not_ inlined. In that case,
we end up with __init code calling a function not marked __init, and we
get the build warnings I'm trying to eliminate in the coming patch that
adds __no_sanitize_coverage to __init functions:
This problem is somewhat fragile (though using either __always_inline
or __init will deterministically solve it), but we've tripped over
this before with GCC and the solution has usually been to just use
__always_inline and move on.
For arm64 this requires forcing one ACPI function to be inlined with
__always_inline.
When the volume header contains erroneous values that do not reflect
the actual state of the filesystem, hfsplus_fill_super() assumes that
the attributes file is not yet created, which later results in hitting
BUG_ON() when hfsplus_create_attributes_file() is called. Replace this
BUG_ON() with -EIO error with a message to suggest running fsck tool.
where HFSPLUS_MAX_STRLEN is 255 bytes. The issue happens if length
of the structure instance has value bigger than 255 (for example,
65283). In such case, pointer on unicode buffer is going beyond of
the allocated memory.
The patch fixes the issue by checking the length value of
hfsplus_unistr instance and using 255 value in the case if length
value is bigger than HFSPLUS_MAX_STRLEN. Potential reason of such
situation could be a corruption of Catalog File b-tree's node.
Reported-by: Wenzhi Wang <wenzhi.wang@uwaterloo.ca> Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org Reviewed-by: Yangtao Li <frank.li@vivo.com> Link: https://lore.kernel.org/r/20250710230830.110500-1-slava@dubeyko.com Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason of the issue that code doesn't check the correctness
of the requested offset and length. As a result, incorrect value
of offset or/and length could result in access out of allocated
memory.
This patch introduces is_bnode_offset_valid() method that checks
the requested offset value. Also, it introduces
check_and_correct_requested_length() method that checks and
correct the requested length (if it is necessary). These methods
are used in hfsplus_bnode_read(), hfsplus_bnode_write(),
hfsplus_bnode_clear(), hfsplus_bnode_copy(), and hfsplus_bnode_move()
with the goal to prevent the access out of allocated memory
and triggering the crash.
Reported-by: Kun Hu <huk23@m.fudan.edu.cn> Reported-by: Jiaji Qin <jjtan24@m.fudan.edu.cn> Reported-by: Shuoran Bai <baishuoran@hrbeu.edu.cn> Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Link: https://lore.kernel.org/r/20250703214804.244077-1-slava@dubeyko.com Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch introduces is_bnode_offset_valid() method that checks
the requested offset value. Also, it introduces
check_and_correct_requested_length() method that checks and
correct the requested length (if it is necessary). These methods
are used in hfs_bnode_read(), hfs_bnode_write(), hfs_bnode_clear(),
hfs_bnode_copy(), and hfs_bnode_move() with the goal to prevent
the access out of allocated memory and triggering the crash.
res = hfs_find_init(HFS_SB(inode->i_sb)->ext_tree, &fd);
if (!res) {
res = __hfs_ext_cache_extent(&fd, inode, block);
hfs_find_exit(&fd);
}
return res;
}
The problem here that hfs_find_init() is trying to use
HFS_SB(inode->i_sb)->ext_tree that is not initialized yet.
It will be initailized when hfs_btree_open() finishes
the execution.
The patch adds checking of tree pointer in hfs_find_init()
and it reworks the logic of hfs_btree_open() by reading
the b-tree's header directly from the volume. The read_mapping_page()
is exchanged on filemap_grab_folio() that grab the folio from
mapping. Then, sb_bread() extracts the b-tree's header
content and copy it into the folio.
Reported-by: Wenzhi Wang <wenzhi.wang@uwaterloo.ca> Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org Link: https://lore.kernel.org/r/20250710213657.108285-1-slava@dubeyko.com Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot found a race condition when kcm_unattach(psock)
and kcm_release(kcm) are executed at the same time.
kcm_unattach() is missing a check of the flag
kcm->tx_stopped before calling queue_work().
If the kcm has a reserved psock, kcm_unattach() might get executed
between cancel_work_sync() and unreserve_psock() in kcm_release(),
requeuing kcm->tx_work right before kcm gets freed in kcm_done().
Remove kcm->tx_stopped and replace it by the less
error-prone disable_work_sync().
TLS expects that it owns the receive queue of the TCP socket.
This cannot be guaranteed in case the reader of the TCP socket
entered before the TLS ULP was installed, or uses some non-standard
read API (eg. zerocopy ones). Replace the WARN_ON() and a buggy
early exit (which leaves anchor pointing to a freed skb) with real
error handling. Wipe the parsing state and tell the reader to retry.
We already reload the anchor every time we (re)acquire the socket lock,
so the only condition we need to avoid is an out of bounds read
(not having enough bytes in the socket for previously parsed record len).
If some data was read from under TLS but there's enough in the queue
we'll reload and decrypt what is most likely not a valid TLS record.
Leading to some undefined behavior from TLS perspective (corrupting
a stream? missing an alert? missing an attack?) but no kernel crash
should take place.
Since ptp virtual clock is registered only under ptp physical clock, both
ptp_clock and posix_clock must be physical clocks for ptp_vclock_in_use()
to lock &ptp->n_vclocks_mux and check ptp->n_vclocks.
However, when unregistering vclocks in n_vclocks_store(), the locking
ptp->n_vclocks_mux is a physical clock lock, but clk->rwsem of
ptp_clock_unregister() called through device_for_each_child_reverse()
is a virtual clock lock.
Therefore, clk->rwsem used in CPU0 and clk->rwsem used in CPU1 are
different locks, but in lockdep, a false positive occurs because the
possibility of deadlock is determined through lock-class.
To solve this, lock subclass annotation must be added to the posix_clock
rwsem of the vclock.
Reported-by: syzbot+7cfb66a237c4a5fb22ad@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=7cfb66a237c4a5fb22ad Fixes: 73f37068d540 ("ptp: support ptp physical/virtual clocks conversion") Signed-off-by: Jeongjun Park <aha310510@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250728062649.469882-1-aha310510@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Marc has reported that commit 85975daeaa4d ("cpuidle: menu: Avoid
discarding useful information") caused the number of wakeup interrupts
to increase on an idle system [1], which was not expected to happen
after merely allowing shallower idle states to be selected by the
governor in some cases.
However, on the system in question, all of the idle states deeper than
WFI are rejected by the driver due to a firmware issue [2]. This causes
the governor to only consider the recent interval duriation data
corresponding to attempts to enter WFI that are successful and the
recent invervals table is filled with values lower than the scheduler
tick period. Consequently, the governor predicts an idle duration
below the scheduler tick period length and avoids stopping the tick
more often which leads to the observed symptom.
Address it by modifying the governor to update the recent intervals
table also when entering the previously selected idle state fails, so
it knows that the short idle intervals might have been the minority
had the selected idle states been actually entered every time.
The variable ret in icss_iep_extts_enable() was incorrectly declared
as u32, while the function returns int and may return negative error
codes. This will cause sign extension issues and incorrect error
propagation. Update ret to be int to fix error handling.
This change corrects the declaration to avoid potential type mismatch.
When link settings are changed emac->speed is populated by
emac_adjust_link(). The link speed and other settings are then written into
the DRAM. However if both ports are brought down after this and brought up
again or if the operating mode is changed and a firmware reload is needed,
the DRAM is cleared by icssg_config(). As a result the link settings are
lost.
Fix this by calling emac_adjust_link() after icssg_config(). This re
populates the settings in the DRAM after a new firmware load.
There is a reference count leak in ctnetlink_dump_table():
if (res < 0) {
nf_conntrack_get(&ct->ct_general); // HERE
cb->args[1] = (unsigned long)ct;
...
While its very unlikely, its possible that ct == last.
If this happens, then the refcount of ct was already incremented.
This 2nd increment is never undone.
This prevents the conntrack object from being released, which in turn
keeps prevents cnet->count from dropping back to 0.
This will then block the netns dismantle (or conntrack rmmod) as
nf_conntrack_cleanup_net_list() will wait forever.
This can be reproduced by running conntrack_resize.sh selftest in a loop.
It takes ~20 minutes for me on a preemptible kernel on average before
I see a runaway kworker spinning in nf_conntrack_cleanup_net_list.
One fix would to change this to:
if (res < 0) {
if (ct != last)
nf_conntrack_get(&ct->ct_general);
But this reference counting isn't needed in the first place.
We can just store a cookie value instead.
A followup patch will do the same for ctnetlink_exp_dump_table,
it looks to me as if this has the same problem and like
ctnetlink_dump_table, we only need a 'skip hint', not the actual
object so we can apply the same cookie strategy there as well.
Commit b40c5f4fde22 ("udp: disable inner UDP checksum offloads in
IPsec case") tried to fix checksumming in UFO when the packets are
going through IPsec, so that we can't rely on offloads because the UDP
header and payload will be encrypted.
But when doing a TCP test over VXLAN going through IPsec transport
mode with GSO enabled (esp4_offload module loaded), I'm seeing broken
UDP checksums on the encap after successful decryption.
The skbs get to udp4_ufo_fragment/__skb_udp_tunnel_segment via
__dev_queue_xmit -> validate_xmit_skb -> skb_gso_segment and at this
point we've already dropped the dst (unless the device sets
IFF_XMIT_DST_RELEASE, which is not common), so need_ipsec is false and
we proceed with checksum offload.
Make need_ipsec also check the secpath, which is not dropped on this
callpath.
smaps_hugetlb_range() handles the pte without holdling ptl, and may be
concurrenct with migration, leaing to BUG_ON in pfn_swap_entry_to_page().
The race is as follows.
As soon as we'd inserted a file reference into descriptor table, another
thread could close it. That's fine for the case when all we are doing is
returning that descriptor to userland (it's a race, but it's a userland
race and there's nothing the kernel can do about it). However, if we
follow fd_install() with any kind of access to objects that would be
destroyed on close (be it the struct file itself or anything destroyed
by its ->release()), we have a UAF.
dma_buf_fd() is a combination of reserving a descriptor and fd_install().
habanalabs export_dmabuf() calls it and then proceeds to access the
objects destroyed on close. In particular, it grabs an extra reference to
another struct file that will be dropped as part of ->release() for ours;
that "will be" is actually "might have already been".
Fix that by reserving descriptor before anything else and do fd_install()
only when everything had been set up. As a side benefit, we no longer
have the failure exit with file already created, but reference to
underlying file (as well as ->dmabuf_export_cnt, etc.) not grabbed yet;
unlike dma_buf_fd(), fd_install() can't fail.
Fixes: db1a8dd916aa ("habanalabs: add support for dma-buf exporter") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set/clear DEBUGCTLMSR_FREEZE_IN_SMM in GUEST_IA32_DEBUGCTL based on the
host's pre-VM-Enter value, i.e. preserve the host's FREEZE_IN_SMM setting
while running the guest. When running with the "default treatment of SMIs"
in effect (the only mode KVM supports), SMIs do not generate a VM-Exit that
is visible to host (non-SMM) software, and instead transitions directly
from VMX non-root to SMM. And critically, DEBUGCTL isn't context switched
by hardware on SMI or RSM, i.e. SMM will run with whatever value was
resident in hardware at the time of the SMI.
Failure to preserve FREEZE_IN_SMM results in the PMU unexpectedly counting
events while the CPU is executing in SMM, which can pollute profiling and
potentially leak information into the guest.
Check for changes in FREEZE_IN_SMM prior to every entry into KVM's inner
run loop, as the bit can be toggled in IRQ context via IPI callback (SMP
function call), by way of /sys/devices/cpu/freeze_on_smi.
Add a field in kvm_x86_ops to communicate which DEBUGCTL bits need to be
preserved, as FREEZE_IN_SMM is only supported and defined for Intel CPUs,
i.e. explicitly checking FREEZE_IN_SMM in common x86 is at best weird, and
at worst could lead to undesirable behavior in the future if AMD CPUs ever
happened to pick up a collision with the bit.
Exempt TDX vCPUs, i.e. protected guests, from the check, as the TDX Module
owns and controls GUEST_IA32_DEBUGCTL.
WARN in SVM if KVM_RUN_LOAD_DEBUGCTL is set, mostly to document that the
lack of handling isn't a KVM bug (TDX already WARNs on any run_flag).
Lastly, explicitly reload GUEST_IA32_DEBUGCTL on a VM-Fail that is missed
by KVM but detected by hardware, i.e. in nested_vmx_restore_host_state().
Doing so avoids the need to track host_debugctl on a per-VMCS basis, as
GUEST_IA32_DEBUGCTL is unconditionally written by prepare_vmcs02() and
load_vmcs12_host_state(). For the VM-Fail case, even though KVM won't
have actually entered the guest, vcpu_enter_guest() will have run with
vmcs02 active and thus could result in vmcs01 being run with a stale value.
Cc: stable@vger.kernel.org Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com> Co-developed-by: Sean Christopherson <seanjc@google.com> Link: https://lore.kernel.org/r/20250610232010.162191-9-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com>
[sean: resolve syntactic conflict in vt_x86_ops definition] Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Introduce vmx_guest_debugctl_{read,write}() to handle all accesses to
vmcs.GUEST_IA32_DEBUGCTL. This will allow stuffing FREEZE_IN_SMM into
GUEST_IA32_DEBUGCTL based on the host setting without bleeding the state
into the guest, and without needing to copy+paste the FREEZE_IN_SMM
logic into every patch that accesses GUEST_IA32_DEBUGCTL.
No functional change intended.
Cc: stable@vger.kernel.org Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
[sean: massage changelog, make inline, use in all prepare_vmcs02() cases] Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com> Link: https://lore.kernel.org/r/20250610232010.162191-8-seanjc@google.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a consistency check for L2's guest_ia32_debugctl, as KVM only supports
a subset of hardware functionality, i.e. KVM can't rely on hardware to
detect illegal/unsupported values. Failure to check the vmcs12 value
would allow the guest to load any harware-supported value while running L2.
Take care to exempt BTF and LBR from the validity check in order to match
KVM's behavior for writes via WRMSR, but without clobbering vmcs12. Even
if VM_EXIT_SAVE_DEBUG_CONTROLS is set in vmcs12, L1 can reasonably expect
that vmcs12->guest_ia32_debugctl will not be modified if writes to the MSR
are being intercepted.
Arguably, KVM _should_ update vmcs12 if VM_EXIT_SAVE_DEBUG_CONTROLS is set
*and* writes to MSR_IA32_DEBUGCTLMSR are not being intercepted by L1, but
that would incur non-trivial complexity and wouldn't change the fact that
KVM's handling of DEBUGCTL is blatantly broken. I.e. the extra complexity
is not worth carrying.
Cc: stable@vger.kernel.org Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com> Co-developed-by: Sean Christopherson <seanjc@google.com> Link: https://lore.kernel.org/r/20250610232010.162191-7-seanjc@google.com
Stable-dep-of: 7d0cce6cbe71 ("KVM: VMX: Wrap all accesses to IA32_DEBUGCTL with getter/setter APIs") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move VMX's logic to check DEBUGCTL values into a standalone helper so that
the code can be used by nested VM-Enter to apply the same logic to the
value being loaded from vmcs12.
KVM needs to explicitly check vmcs12->guest_ia32_debugctl on nested
VM-Enter, as hardware may support features that KVM does not, i.e. relying
on hardware to detect invalid guest state will result in false negatives.
Unfortunately, that means applying KVM's funky suppression of BTF and LBR
to vmcs12 so as not to break existing guests.
No functional change intended.
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com> Link: https://lore.kernel.org/r/20250610232010.162191-6-seanjc@google.com
Stable-dep-of: 7d0cce6cbe71 ("KVM: VMX: Wrap all accesses to IA32_DEBUGCTL with getter/setter APIs") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Let the guest set DEBUGCTL.RTM_DEBUG if RTM is supported according to the
guest CPUID model, as debug support is supposed to be available if RTM is
supported, and there are no known downsides to letting the guest debug RTM
aborts.
Note, there are no known bug reports related to RTM_DEBUG, the primary
motivation is to reduce the probability of breaking existing guests when a
future change adds a missing consistency check on vmcs12.GUEST_DEBUGCTL
(KVM currently lets L2 run with whatever hardware supports; whoops).
Note #2, KVM already emulates DR6.RTM, and doesn't restrict access to
DR7.RTM.
Fixes: 83c529151ab0 ("KVM: x86: expose Intel cpu new features (HLE, RTM) to guest") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250610232010.162191-5-seanjc@google.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instruct vendor code to load the guest's DR6 into hardware via a new
KVM_RUN flag, and remove kvm_x86_ops.set_dr6(), whose sole purpose was to
load vcpu->arch.dr6 into hardware when DR6 can be read/written directly
by the guest.
Note, TDX already WARNs on any run_flag being set, i.e. will yell if KVM
thinks DR6 needs to be reloaded. TDX vCPUs force KVM_DEBUGREG_AUTO_SWITCH
and never clear the flag, i.e. should never observe KVM_RUN_LOAD_GUEST_DR6.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250610232010.162191-4-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com>
[sean: drop TDX changes] Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Convert kvm_x86_ops.vcpu_run()'s "force_immediate_exit" boolean parameter
into an a generic bitmap so that similar "take action" information can be
passed to vendor code without creating a pile of boolean parameters.
This will allow dropping kvm_x86_ops.set_dr6() in favor of a new flag, and
will also allow for adding similar functionality for re-loading debugctl
in the active VMCS.
Opportunistically massage the TDX WARN and comment to prepare for adding
more run_flags, all of which are expected to be mutually exclusive with
TDX, i.e. should be WARNed on.
No functional change intended.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250610232010.162191-3-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com>
[sean: drop TDX changes] Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We already called ib_drain_qp() before and that makes sure
send_done() was called with IB_WC_WR_FLUSH_ERR, but
didn't called atomic_dec_and_test(&sc->send_io.pending.count)
So we may never reach the info->send_pending == 0 condition.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: 5349ae5e05fa ("smb: client: let send_done() cleanup before calling smbd_disconnect_rdma_connection()") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should call ib_dma_unmap_single() and mempool_free() before calling
smbd_disconnect_rdma_connection().
And smbd_disconnect_rdma_connection() needs to be the last function to
call as all other state might already be gone after it returns.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: f198186aa9bb ("CIFS: SMBD: Establish SMB Direct connection") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since these values can be large, the multiplication may exceed the
maximum value of an int (INT_MAX) and overflow (Our platform did),
leading to an incorrect adist.
User-visible impact:
The memory tiering subsystem will misinterpret slow memory (like CXL)
as faster than DRAM, causing inappropriate demotion of pages from
CXL (slow memory) to DRAM (fast memory).
For example, we will see the following demotion chains from the dmesg, where
Node0,1 are DRAM, and Node2,3 are CXL node:
Demotion targets for Node 0: null
Demotion targets for Node 1: null
Demotion targets for Node 2: preferred: 0-1, fallback: 0-1
Demotion targets for Node 3: preferred: 0-1, fallback: 0-1
Change MEMTIER_ADISTANCE_DRAM to be a long constant by writing it with
the 'L' suffix. This prevents the overflow because the multiplication
will then be done in the long type which has a larger range.
Link: https://lkml.kernel.org/r/20250611023439.2845785-1-lizhijian@fujitsu.com Link: https://lkml.kernel.org/r/20250610062751.2365436-1-lizhijian@fujitsu.com Fixes: 3718c02dbd4c ("acpi, hmat: calculate abstract distance with HMAT") Signed-off-by: Li Zhijian <lizhijian@fujitsu.com> Reviewed-by: Huang Ying <ying.huang@linux.alibaba.com> Acked-by: Balbir Singh <balbirs@nvidia.com> Reviewed-by: Donet Tom <donettom@linux.ibm.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REQ_OP_ZONE_FINISH is defined as "12", which makes
op_is_write(REQ_OP_ZONE_FINISH) return false, despite the fact that a
zone finish operation is an operation that modifies a zone (transition
it to full) and so should be considered as a write operation (albeit
one that does not transfer any data to the device).
Fix this by redefining REQ_OP_ZONE_FINISH to be an odd number (13), and
redefine REQ_OP_ZONE_RESET and REQ_OP_ZONE_RESET_ALL using sequential
odd numbers from that new value.
Fixes: 6c1b1da58f8c ("block: add zone open, close and finish operations") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20250625093327.548866-2-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d33bd88ac0eb ("ACPI: processor: perflib: Fix initial _PPC limit
application") added a pr->performance check that prevents the frequency
QoS request from being added when the given processor has no performance
object. Unfortunately, this causes a WARN() in freq_qos_remove_request()
to trigger on an attempt to take the given CPU offline later because the
frequency QoS object has not been added for it due to the missing
performance object.
Address this by moving the pr->performance check before calling
acpi_processor_get_platform_limit() so it only prevents a limit from
being set for the CPU if the performance object is not present. This
way, the frequency QoS request is added as it was before the above
commit and it is present all the time along with the CPU's cpufreq
policy regardless of whether or not the CPU is online.
Fixes: d33bd88ac0eb ("ACPI: processor: perflib: Fix initial _PPC limit application") Tested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/2801421.mvXUDI8C0e@rafael.j.wysocki Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the BIOS sets a _PPC frequency limit upfront, it will fail to take
effect due to a call ordering issue. Namely, freq_qos_update_request()
is called before freq_qos_add_request() for the given request causing
the constraint update to be ignored. The call sequence in question is
as follows:
Address this by adding an acpi_processor_get_platform_limit() call
to acpi_processor_ppc_init(), after the perflib_req activation via
freq_qos_add_request(), which causes the initial _PPC limit to be
picked up as appropriate. However, also ensure that the _PPC limit
will not be picked up in the cases when the cpufreq driver does not
call acpi_processor_register_performance() by adding a pr->performance
check to the related_cpus loop in acpi_processor_ppc_init().
Fixes: d15ce412737a ("ACPI: cpufreq: Switch to QoS requests instead of cpufreq notifier") Signed-off-by: Jiayi Li <lijiayi@kylinos.cn> Link: https://patch.msgid.link/20250721032606.3459369-1-lijiayi@kylinos.cn
[ rjw: Consolidate pr-related checks in acpi_processor_ppc_init() ]
[ rjw: Subject and changelog adjustments ] Cc: 5.4+ <stable@vger.kernel.org> # 5.4+: 2d8b39a62a5d ACPI: processor: Avoid NULL pointer dereferences at init time Cc: 5.4+ <stable@vger.kernel.org> # 5.4+: 3000ce3c52f8 cpufreq: Use per-policy frequency QoS Cc: 5.4+ <stable@vger.kernel.org> # 5.4+: a1bb46c36ce3 ACPI: processor: Add QoS requests for all CPUs Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The _CRS resources in many cases want to have ResourceSource field
to be a type of ACPI String. This means that to compile properly
we need to enclosure the name path into double quotes. This will
in practice defer the interpretation to a run-time stage, However,
this may be interpreted differently on different OSes and ACPI
interpreter implementations. In particular ACPICA might not correctly
recognize the leading '^' (caret) character and will not resolve
the relative name path properly. On top of that, this piece may be
used in SSDTs which are loaded after the DSDT and on itself may also
not resolve relative name paths outside of their own scopes.
With this all said, fix documentation to use fully-qualified name
paths always to avoid any misinterpretations, which is proven to
work.
Fixes: 8eb5c87a92c0 ("i2c: add ACPI support for I2C mux ports") Reported-by: Yevhen Kondrashyn <e.kondrashyn@gmail.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://patch.msgid.link/20250710170225.961303-1-andriy.shevchenko@linux.intel.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that epoll instances can never form a graph deeper than
EP_MAX_NESTS+1 links.
Currently, ep_loop_check_proc() ensures that the graph is loop-free and
does some recursion depth checks, but those recursion depth checks don't
limit the depth of the resulting tree for two reasons:
- They don't look upwards in the tree.
- If there are multiple downwards paths of different lengths, only one of
the paths is actually considered for the depth check since commit 28d82dc1c4ed ("epoll: limit paths").
Essentially, the current recursion depth check in ep_loop_check_proc() just
serves to prevent it from recursing too deeply while checking for loops.
A more thorough check is done in reverse_path_check() after the new graph
edge has already been created; this checks, among other things, that no
paths going upwards from any non-epoll file with a length of more than 5
edges exist. However, this check does not apply to non-epoll files.
As a result, it is possible to recurse to a depth of at least roughly 500,
tested on v6.15. (I am unsure if deeper recursion is possible; and this may
have changed with commit 8c44dac8add7 ("eventpoll: Fix priority inversion
problem").)
To fix it:
1. In ep_loop_check_proc(), note the subtree depth of each visited node,
and use subtree depths for the total depth calculation even when a subtree
has already been visited.
2. Add ep_get_upwards_depth_proc() for similarly determining the maximum
depth of an upwards walk.
3. In ep_loop_check(), use these values to limit the total path length
between epoll nodes to EP_MAX_NESTS edges.
When sysctl_nr_open is set to a very high value (for example, 1073741816
as set by systemd), processes attempting to use file descriptors near
the limit can trigger massive memory allocation attempts that exceed
INT_MAX, resulting in a WARNING in mm/slub.c:
WARNING: CPU: 0 PID: 44 at mm/slub.c:5027 __kvmalloc_node_noprof+0x21a/0x288
This happens because kvmalloc_array() and kvmalloc() check if the
requested size exceeds INT_MAX and emit a warning when the allocation is
not flagged with __GFP_NOWARN.
Specifically, when nr_open is set to 1073741816 (0x3ffffff8) and a
process calls dup2(oldfd, 1073741880), the kernel attempts to allocate:
- File descriptor array: 1073741880 * 8 bytes = 8,589,935,040 bytes
- Multiple bitmaps: ~400MB
- Total allocation size: > 8GB (exceeding INT_MAX = 2,147,483,647)
Reproducer:
1. Set /proc/sys/fs/nr_open to 1073741816:
# echo 1073741816 > /proc/sys/fs/nr_open
2. Run a program that uses a high file descriptor:
#include <unistd.h>
#include <sys/resource.h>
int main() {
struct rlimit rlim = {1073741824, 1073741824};
setrlimit(RLIMIT_NOFILE, &rlim);
dup2(2, 1073741880); // Triggers the warning
return 0;
}
3. Observe WARNING in dmesg at mm/slub.c:5027
systemd commit a8b627a introduced automatic bumping of fs.nr_open to the
maximum possible value. The rationale was that systems with memory
control groups (memcg) no longer need separate file descriptor limits
since memory is properly accounted. However, this change overlooked
that:
1. The kernel's allocation functions still enforce INT_MAX as a maximum
size regardless of memcg accounting
2. Programs and tests that legitimately test file descriptor limits can
inadvertently trigger massive allocations
3. The resulting allocations (>8GB) are impractical and will always fail
systemd's algorithm starts with INT_MAX and keeps halving the value
until the kernel accepts it. On most systems, this results in nr_open
being set to 1073741816 (0x3ffffff8), which is just under 1GB of file
descriptors.
While processes rarely use file descriptors near this limit in normal
operation, certain selftests (like
tools/testing/selftests/core/unshare_test.c) and programs that test file
descriptor limits can trigger this issue.
Fix this by adding a check in alloc_fdtable() to ensure the requested
allocation size does not exceed INT_MAX. This causes the operation to
fail with -EMFILE instead of triggering a kernel warning and avoids the
impractical >8GB memory allocation request.
Fixes: 9cfe015aa424 ("get rid of NR_OPEN and introduce a sysctl_nr_open") Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Link: https://lore.kernel.org/20250629074021.1038845-1-sashal@kernel.org Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make fscrypt no longer use Crypto API drivers for non-inline crypto
engines, even when the Crypto API prioritizes them over CPU-based code
(which unfortunately it often does). These drivers tend to be really
problematic, especially for fscrypt's workload. This commit has no
effect on inline crypto engines, which are different and do work well.
Specifically, exclude drivers that have CRYPTO_ALG_KERN_DRIVER_ONLY or
CRYPTO_ALG_ALLOCATES_MEMORY set. (Later, CRYPTO_ALG_ASYNC should be
excluded too. That's omitted for now to keep this commit backportable,
since until recently some CPU-based code had CRYPTO_ALG_ASYNC set.)
There are two major issues with these drivers: bugs and performance.
First, these drivers tend to be buggy. They're fundamentally much more
error-prone and harder to test than the CPU-based code. They often
don't get tested before kernel releases, and even if they do, the crypto
self-tests don't properly test these drivers. Released drivers have
en/decrypted or hashed data incorrectly. These bugs cause issues for
fscrypt users who often didn't even want to use these drivers, e.g.:
These drivers have also similarly caused issues for dm-crypt users,
including data corruption and deadlocks. Since Linux v5.10, dm-crypt
has disabled most of them by excluding CRYPTO_ALG_ALLOCATES_MEMORY.
Second, these drivers tend to be *much* slower than the CPU-based code.
This may seem counterintuitive, but benchmarks clearly show it. There's
a *lot* of overhead associated with going to a hardware driver, off the
CPU, and back again. To prove this, I gathered as many systems with
this type of crypto engine as I could, and I measured synchronous
encryption of 4096-byte messages (which matches fscrypt's workload):
So, there was no case in which the crypto engine was even *close* to
being faster. On the first three, which have AES instructions in the
CPU, the CPU was 30 to 55 times faster (!). Even on STM32MP157F-DK2
which has a Cortex-A7 CPU that doesn't have AES instructions, AES was
over 4 times faster on the CPU. And Adiantum encryption, which is what
actually should be used on CPUs like that, was over 17 times faster.
Other justifications that have been given for these non-inline crypto
engines (almost always coming from the hardware vendors, not actual
users) don't seem very plausible either:
- The crypto engine throughput could be improved by processing
multiple requests concurrently. Currently irrelevant to fscrypt,
since it doesn't do that. This would also be complex, and unhelpful
in many cases. 2 of the 4 engines I tested even had only one queue.
- Some of the engines, e.g. STM32, support hardware keys. Also
currently irrelevant to fscrypt, since it doesn't support these.
Interestingly, the STM32 driver itself doesn't support this either.
- Free up CPU for other tasks and/or reduce energy usage. Not very
plausible considering the "short" message length, driver overhead,
and scheduling overhead. There's just very little time for the CPU
to do something else like run another task or enter low-power state,
before the message finishes and it's time to process the next one.
- Some of these engines resist power analysis and electromagnetic
attacks, while the CPU-based crypto generally does not. In theory,
this sounds great. In practice, if this benefit requires the use of
an off-CPU offload that massively regresses performance and has a
low-quality, buggy driver, the price for this hardening (which is
not relevant to most fscrypt users, and tends to be incomplete) is
just too high. Inline crypto engines are much more promising here,
as are on-CPU solutions like RISC-V High Assurance Cryptography.
Using device_find_child() to locate a probed virtual-device-port node
causes a device refcount imbalance, as device_find_child() internally
calls get_device() to increment the device’s reference count before
returning its pointer. vdc_port_mpgroup_check() directly returns true
upon finding a matching device without releasing the reference via
put_device(). We should call put_device() to decrement refcount.
As comment of device_find_child() says, 'NOTE: you will need to drop
the reference with put_device() after use'.
Found by code review.
Cc: stable@vger.kernel.org Fixes: 3ee70591d6c4 ("sunvdc: prevent sunvdc panic when mpgroup disk added to guest domain") Signed-off-by: Ma Ke <make24@iscas.ac.cn> Link: https://lore.kernel.org/r/20250719075856.3447953-1-make24@iscas.ac.cn Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In init_cpu_fullname(), a constant pointer to "model" property is
retrieved. It's later modified by the strsep() function, which is
illegal and corrupts kernel's FDT copy. This is shown by dmesg,
OF: fdt: not creating '/sys/firmware/fdt': CRC check failed
Create a mutable copy of the model property and do in-place operations
on the mutable copy instead. loongson_sysconf.cpuname lives across the
kernel lifetime, thus manually releasing isn't necessary.
Also move the of_node_put() call for the root node after the usage of
its property, since of_node_put() decreases the reference counter thus
usage after the call is unsafe.
Cc: stable@vger.kernel.org Fixes: 44a01f1f726a ("LoongArch: Parsing CPU-related information from DTS") Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Yao Zi <ziyao@disroot.org> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now relocate_new_kernel_size is a .long value, which means 32bit, so its
high 32bit is undefined. This causes memcpy((void *)reboot_code_buffer,
relocate_new_kernel, relocate_new_kernel_size) in machine_kexec_prepare()
access out of range memories in some cases, and then end up with an ADE
exception.
So make relocate_new_kernel_size be a .quad value, which means 64bit, to
avoid such errors.
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and easier to
reason about.
The extra pass of bpf_int_jit_compile() skips JIT context initialization
which essentially skips offset calculation leaving out_offset = -1, so
the jmp_offset in emit_bpf_tail_call is calculated by
"#define jmp_offset (out_offset - (cur_offset))"
is a negative number, which is wrong. The final generated assembly are
as follow.
Like s390 and the jailhouse hypervisor, LoongArch's PCI architecture allows
passing isolated PCI functions to a guest OS instance. So it is possible
that there is a multi-function device without function 0 for the host or
guest.
Allow probing such functions by adding a IS_ENABLED(CONFIG_LOONGARCH) case
in the hypervisor_isolated_pci_functions() helper.
This is similar to commit 189c6c33ff42 ("PCI: Extend isolated function
probing to s390").
When the client sends an OPEN with claim type CLAIM_DELEG_CUR_FH or
CLAIM_DELEGATION_CUR, the delegation stateid and the file handle
must belong to the same file, otherwise return NFS4ERR_INVAL.
Note that RFC8881, section 8.2.4, mandates the server to return
NFS4ERR_BAD_STATEID if the selected table entry does not match the
current filehandle. However returning NFS4ERR_BAD_STATEID in the
OPEN causes the client to retry the operation and therefor get the
client into a loop. To avoid this situation we return NFS4ERR_INVAL
instead.
Reported-by: Petro Pavlov <petro.pavlov@vastdata.com> Fixes: c44c5eeb2c02 ("[PATCH] nfsd4: add open state code for CLAIM_DELEGATE_CUR") Cc: stable@vger.kernel.org Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lei Lu recently reported that nfsd4_setclientid_confirm() did not check
the return value from get_client_locked(). a SETCLIENTID_CONFIRM could
race with a confirmed client expiring and fail to get a reference. That
could later lead to a UAF.
Fix this by getting a reference early in the case where there is an
extant confirmed client. If that fails then treat it as if there were no
confirmed client found at all.
In the case where the unconfirmed client is expiring, just fail and
return the result from get_client_locked().
Reported-by: lei lu <llfamsec@gmail.com> Closes: https://lore.kernel.org/linux-nfs/CAEBF3_b=UvqzNKdnfD_52L05Mqrqui9vZ2eFamgAbV0WG+FNWQ@mail.gmail.com/ Fixes: d20c11d86d8f ("nfsd: Protect session creation and client confirm using client_lock") Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without setting phy_mask for ax88772 mdio bus, current driver may create
at most 32 mdio phy devices with phy address range from 0x00 ~ 0x1f.
DLink DUB-E100 H/W Ver B1 is such a device. However, only one main phy
device will bind to net phy driver. This is creating issue during system
suspend/resume since phy_polling_mode() in phy_state_machine() will
directly deference member of phydev->drv for non-main phy devices. Then
NULL pointer dereference issue will occur. Due to only external phy or
internal phy is necessary, add phy_mask for ax88772 mdio bus to workarnoud
the issue.
Make sure to drop the references to the IEP OF node and device taken by
of_parse_phandle() and of_find_device_by_node() when looking up IEP
devices during probe.
Drop the bogus additional reference taken on successful lookup so that
the device is released correctly by icss_iep_put().
Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Cc: stable@vger.kernel.org # 6.6 Cc: Roger Quadros <rogerq@kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250725171213.880-6-johan@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reference count to the WED devices has already been incremented when
looking them up using of_find_device_by_node() so drop the bogus
additional reference taken during probe.
Fixes: 804775dfc288 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)") Cc: stable@vger.kernel.org # 5.19 Cc: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250725171213.880-5-johan@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the references to the IERB OF node and platform device
taken by of_parse_phandle() and of_find_device_by_node() during probe.
Fixes: e7d48e5fbf30 ("net: enetc: add a mini driver for the Integrated Endpoint Register Block") Cc: stable@vger.kernel.org # 5.13 Cc: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250725171213.880-3-johan@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the call to phy_disconnect() netdev->phydev is reset to NULL.
So fixed_phy_unregister() would be called with a NULL pointer as argument.
Therefore cache the phy_device before this call.
Fixes: e24a6c874601 ("net: ftgmac100: Get link speed and duplex for NC-SI") Cc: stable@vger.kernel.org Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com> Link: https://patch.msgid.link/2b80a77a-06db-4dd7-85dc-3a8e0de55a1d@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 21b688dabecb ("net: phy: micrel: Cable Diag feature for lan8814
phy") introduced cable_test support for the LAN8814 that reuses parts of
the KSZ886x logic and introduced the cable_diag_reg and pair_mask
parameters to account for differences between those chips.
However, it did not update the ksz8081_type struct, so those members are
now 0, causing no pairs to be tested in ksz886x_cable_test_get_status
and ksz886x_cable_test_wait_for_completion to poll the wrong register
for the affected PHYs (Basic Control/Reset, which is 0 in normal
operation) and exit immediately.
Fix this by setting both struct members accordingly.
netlink_attachskb() checks for the socket's read memory allocation
constraints. Firstly, it has:
rmem < READ_ONCE(sk->sk_rcvbuf)
to check if the just increased rmem value fits into the socket's receive
buffer. If not, it proceeds and tries to wait for the memory under:
rmem + skb->truesize > READ_ONCE(sk->sk_rcvbuf)
The checks don't cover the case when skb->truesize + sk->sk_rmem_alloc is
equal to sk->sk_rcvbuf. Thus the function neither successfully accepts
these conditions, nor manages to reschedule the task - and is called in
retry loop for indefinite time which is caught as:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 0-....: (25999 ticks this GP) idle=ef2/1/0x4000000000000000 softirq=262269/262269 fqs=6212
(t=26000 jiffies g=230833 q=259957)
NMI backtrace for cpu 0
CPU: 0 PID: 22 Comm: kauditd Not tainted 5.10.240 #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc42 04/01/2014
Call Trace:
<IRQ>
dump_stack lib/dump_stack.c:120
nmi_cpu_backtrace.cold lib/nmi_backtrace.c:105
nmi_trigger_cpumask_backtrace lib/nmi_backtrace.c:62
rcu_dump_cpu_stacks kernel/rcu/tree_stall.h:335
rcu_sched_clock_irq.cold kernel/rcu/tree.c:2590
update_process_times kernel/time/timer.c:1953
tick_sched_handle kernel/time/tick-sched.c:227
tick_sched_timer kernel/time/tick-sched.c:1399
__hrtimer_run_queues kernel/time/hrtimer.c:1652
hrtimer_interrupt kernel/time/hrtimer.c:1717
__sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1113
asm_call_irq_on_stack arch/x86/entry/entry_64.S:808
</IRQ>
While .led_blink_set() would previously put an LED into an unconditional
permanently blinking state, the offending commit now uses same operation
to (also?) set the blink timing of the netdev trigger when offloading.
This breaks many if not all of the existing PHY drivers which offer
offloading LED operations, as those drivers would just put the LED into
blinking state after .led_blink_set() has been called.
Unfortunately the change even made it into stable kernels for unknown
reasons, so it should be reverted there as well.
Driver in probe() updates each of 'reg_field' with 'reg_base':
for (i = 0; i < REG_MAX_COUNT; i++)
regs[i].reg += reg_base;
'reg_field' array (under variable 'regs' above) is statically allocated,
thus each re-bind would add another 'reg_base' leading to bogus
register addresses. Constify the local 'reg_field' array and duplicate
it in probe to solve this.
Fixes: 96a2e242a5dc ("leds: flash: Add driver to support flash LED module in QCOM PMICs") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Fenglin Wu <fenglin.wu@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250529063335.8785-2-krzysztof.kozlowski@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpio-mlxbf3 driver interfaces with two GPIO controllers,
device instance 0 and 1. There is a single IRQ resource shared
between the two controllers, and it is found in the ACPI table for
device instance 0. The driver should not use platform_get_irq(),
otherwise this error is logged when probing instance 1:
mlxbf3_gpio MLNXBF33:01: error -ENXIO: IRQ index 0 not found
While this change was merged, it is not the preferred solution.
During review of a similar change to the gpio-mlxbf2 driver, the
use of "platform_get_irq_optional" was identified as the preferred
solution, so let's use it for gpio-mlxbf3 driver as well.
Cc: stable@vger.kernel.org Fixes: 10af0273a35a ("gpio: mlxbf3: only get IRQ for device instance 0") Signed-off-by: David Thompson <davthompson@nvidia.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/8d2b630c71b3742f2c74242cf7d602706a6108e6.1754928650.git.davthompson@nvidia.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpio-mlxbf2 driver interfaces with four GPIO controllers,
device instances 0-3. There are two IRQ resources shared between
the four controllers, and they are found in the ACPI table for
instances 0 and 3. The driver should not use platform_get_irq(),
otherwise this error is logged when probing instances 1 and 2:
mlxbf2_gpio MLNXBF22:01: error -ENXIO: IRQ index 0 not found
projects / thirdparty / kernel / stable.git / log
