It is completely wrong to check for compile-time MIPS ISA revision in
the body of bpf_int_jit_compile() as it may lead to get MIPS JIT fully
omitted by the CC while the rest system will think that the JIT is
actually present and works [1].
We can check if the selected CPU really supports MIPS eBPF JIT at
configure time and avoid such situations when kernel can be built
without both JIT and interpreter, but with CONFIG_BPF_SYSCALL=y.
Commit 716850ab104d ("MIPS: eBPF: Initial eBPF support for MIPS32
architecture.") enabled our eBPF JIT for MIPS32 kernels, whereas it has
previously only been availailable for MIPS64. It was my understanding at
the time that the BPF test suite was passing & JITing a comparable
number of tests to our cBPF JIT [1], but it turns out that was not the
case.
The eBPF JIT has a number of problems on MIPS32:
- Most notably various code paths still result in emission of MIPS64
instructions which will cause reserved instruction exceptions & kernel
panics when run on MIPS32 CPUs.
- The eBPF JIT doesn't account for differences between the O32 ABI used
by MIPS32 kernels versus the N64 ABI used by MIPS64 kernels. Notably
arguments beyond the first 4 are passed on the stack in O32, and this
is entirely unhandled when JITing a BPF_CALL instruction. Stack space
must be reserved for arguments even if they all fit in registers, and
the callee is free to assume that stack space has been reserved for
its use - with the eBPF JIT this is not the case, so calling any
function can result in clobbering values on the stack & unpredictable
behaviour. Function arguments in eBPF are always 64-bit values which
is also entirely unhandled - the JIT still uses a single (32-bit)
register per argument. As a result all function arguments are always
passed incorrectly when JITing a BPF_CALL instruction, leading to
kernel crashes or strange behavior.
- The JIT attempts to bail our on use of ALU64 instructions or 64-bit
memory access instructions. The code doing this at the start of
build_one_insn() incorrectly checks whether BPF_OP() equals BPF_DW,
when it should really be checking BPF_SIZE() & only doing so when
BPF_CLASS() is one of BPF_{LD,LDX,ST,STX}. This results in false
positives that cause more bailouts than intended, and that in turns
hides some of the problems described above.
- The kernel's cBPF->eBPF translation makes heavy use of 64-bit eBPF
instructions that the MIPS32 eBPF JIT bails out on, leading to most
cBPF programs not being JITed at all.
Until these problems are resolved, revert the enabling of the eBPF JIT
on MIPS32 done by commit 716850ab104d ("MIPS: eBPF: Initial eBPF support
for MIPS32 architecture.").
Note that this does not undo the changes made to the eBPF JIT by that
commit, since they are a useful starting point to providing MIPS32
support - they're just not nearly complete.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This table is used for lots of things, add it's own lock.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the HDMI unbinds drm_connector_cleanup() and drm_encoder_cleanup()
are called. This also happens when the connector and the encoder are
destroyed. This double call triggers a NULL pointer exception.
The patch fixes this by removing the cleanup calls in the unbind
function.
Klaus Ethgen reported occasional high CPU usages in his system that
seem caused by HD-audio driver. The perf output revealed that it's
in the unsolicited event handling in the workqueue, and the problem
seems triggered by some communication stall between the controller and
the codec at the runtime or system resume.
Actually a similar phenomenon was seen in the past for other Intel
platforms, and we already applied the workaround to enforce sync-write
for CORB/RIRB verbs for Skylake and newer chipsets (commit 2756d9143aa5 "ALSA: hda - Fix intermittent CORB/RIRB stall on Intel
chips"). Fortunately, the same workaround is applicable to the old
chipset, and the experiment showed the positive effect.
Based on the experiment result, this patch enables the sync-write
workaround for all Intel chipsets. The only reason I hesitated to
apply this workaround was about the possibly slightly higher CPU usage.
But if the lack of sync causes a much severer problem even for quite
old chip, we should think this would be necessary for all Intel chips.
Recently we found the headset-mic on the Dell Dock WD19 doesn't work
anymore after s3 (s2i or deep), this problem could be workarounded by
closing (pcm_close) the app and then reopening (pcm_open) the app, so
this bug is not easy to be detected by users.
When problem happens, retire_capture_urb() could still be called
periodically, but the size of captured data is always 0, it could be
a firmware bug on the dock. Anyway I found after resuming, the
snd_usb_pcm_prepare() will be called, and if we forcibly run
set_format() to set the interface and its endpoint, the capture
size will be normal again. This problem and workaound also apply to
playback.
To fix it in the kernel, add a quirk to let set_format() run
forcibly once after resume.
Make sure to check the return value of usb_altnum_to_altsetting() to
avoid dereferencing a NULL pointer when the requested alternate settings
is missing.
The format altsetting number may come from a quirk table and there does
not seem to be any other validation of it (the corresponding index is
checked however).
Jia-Ju Bai reported a possible sleep-in-atomic scenario in the ice1724
driver with Infrasonic Quartet support code: namely, ice->set_rate
callback gets called inside ice->reg_lock spinlock, while the callback
in quartet.c holds ice->gpio_mutex.
This patch fixes the invalid call: it simply moves the calls of
ice->set_rate and ice->set_mclk callbacks outside the spinlock.
To fix this, do what we do for cache read faults already: drop the
mmap_sem before calling into anything IO bound, in this case the
balance_dirty_pages() function, and return VM_FAULT_RETRY.
Link: http://lkml.kernel.org/r/20190924194238.GA29030@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some filesystem, such as vfat, may send bio which crosses device boundary,
and the worse thing is that the IO request starting within device boundaries
can contain more than one segment past EOD.
Commit dce30ca9e3b6 ("fs: fix guard_bio_eod to check for real EOD errors")
tries to fix this issue by returning -EIO for this situation. However,
this way lets fs user code lose chance to handle -EIO, then sync_inodes_sb()
may hang for ever.
Also the current truncating on last segment is dangerous by updating the
last bvec, given bvec table becomes not immutable any more, and fs bio
users may not retrieve the truncated pages via bio_for_each_segment_all() in
its .end_io callback.
Fixes this issue by supporting multi-segment truncating. And the
approach is simpler:
- just update bio size since block layer can make correct bvec with
the updated bio size. Then bvec table becomes really immutable.
- zero all truncated segments for read bio
Cc: Carlos Maiolino <cmaiolino@redhat.com> Cc: linux-fsdevel@vger.kernel.org Fixed-by: dce30ca9e3b6 ("fs: fix guard_bio_eod to check for real EOD errors") Reported-by: syzbot+2b9e54155c8c25d8d165@syzkaller.appspotmail.com Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
On Big Endian architectures, u16 port value was extracted from the wrong
parts of u32 sreg_port, just like commit 10596608c4d62 ("netfilter:
nf_tables: fix mismatch in big-endian system") describes.
We made the error message for the CORB/RIRB communication clearer by
upgrading to dev_WARN() so that user can notice better. But this
struck us like a boomerang: now it caught syzbot and reported back as
a fatal issue although it's not really any too serious bug that worth
for stopping the whole system.
OK, OK, let's be softy, downgrade it to the standard dev_err() again.
Fixes: dd65f7e19c69 ("ALSA: hda - Show the fatal CORB/RIRB error more clearly") Reported-by: syzbot+b3028ac3933f5c466389@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20191216151224.30013-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When assiging and testing taskstats in taskstats_exit() there's a race
when setting up and reading sig->stats when a thread-group with more
than one thread exits:
write to 0xffff8881157bbe10 of 8 bytes by task 7951 on cpu 0:
taskstats_tgid_alloc kernel/taskstats.c:567 [inline]
taskstats_exit+0x6b7/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
get_signal+0x2a2/0x1320 kernel/signal.c:2734
do_signal+0x3b/0xc00 arch/x86/kernel/signal.c:815
exit_to_usermode_loop+0x250/0x2c0 arch/x86/entry/common.c:159
prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
do_syscall_64+0x2d7/0x2f0 arch/x86/entry/common.c:299
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8881157bbe10 of 8 bytes by task 7949 on cpu 1:
taskstats_tgid_alloc kernel/taskstats.c:559 [inline]
taskstats_exit+0xb2/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
__do_sys_exit_group kernel/exit.c:994 [inline]
__se_sys_exit_group kernel/exit.c:992 [inline]
__x64_sys_exit_group+0x2e/0x30 kernel/exit.c:992
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by using smp_load_acquire() and smp_store_release().
Reported-by: syzbot+c5d03165a1bd1dead0c1@syzkaller.appspotmail.com Fixes: 34ec12349c8a ("taskstats: cleanup ->signal->stats allocation") Cc: stable@vger.kernel.org Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Acked-by: Marco Elver <elver@google.com> Reviewed-by: Will Deacon <will@kernel.org> Reviewed-by: Andrea Parri <parri.andrea@gmail.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Link: https://lore.kernel.org/r/20191009114809.8643-1-christian.brauner@ubuntu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
BUG: KASAN: use-after-free in perf_trace_lock_acquire+0x401/0x530 include/trace/events/lock.h:13
Read of size 8 at addr ffff8880a5cf2c50 by task syz-executor.0/26173
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7275 Comm: sshd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: b75eba76d3d7 ("tcp: send in-queue bytes in cmsg upon read") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The auto-parser assigns the bass speaker to DAC3 (NID 0x06) which
is without the volume control. I do not see a reason to use DAC2,
because the shared output to all speakers produces the sufficient
and well balanced sound. The stereo support is enough for this
purpose (laptop).
Nvidia proprietary driver doesn't support runtime power management, so
when a user only wants to use the integrated GPU, it's a common practice
to let dGPU not to bind any driver, and let its upstream port to be
runtime suspended. At the end of runtime suspension the port uses
platform power management to disable power through _OFF method of power
resource, which is listed by _PR3.
After commit b516ea586d71 ("PCI: Enable NVIDIA HDA controllers"), when
the dGPU comes with an HDA function, the HDA won't be suspended if the
dGPU is unbound, so the power resource can't be turned off by its
upstream port driver.
Commit 37a3a98ef601 ("ALSA: hda - Enable runtime PM only for
discrete GPU") only allows HDA to be runtime suspended once GPU is
bound, to keep APU's HDA working.
However, HDA on dGPU isn't that useful if dGPU is not bound to any
driver. So let's relax the runtime suspend requirement for dGPU's HDA
function, to disable the power source to save lots of power.
ASUS reported that there's an bass speaker in addition to internal
speaker and it uses DAC 0x02. It was not enabled in the commit 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS
UX431FLC") which only enables the amplifier and the front speaker.
This commit enables the bass speaker on top of the aforementioned
work to improve the acoustic experience.
Fixes: 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS UX431FLC") Signed-off-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191230031118.95076-1-chiu@endlessm.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When looking for a bit by number we make use of the cached result from the
preceding lookup to speed up operation. Firstly we check if the requested
pfn is within the cached zone and if not lookup the new zone. We then
check if the offset for that pfn falls within the existing cached node.
This happens regardless of whether the node is within the zone we are
now scanning. With certain memory layouts it is possible for this to
false trigger creating a temporary alias for the pfn to a different bit.
This leads the hibernation code to free memory which it was never allocated
with the expected fallout.
Ensure the zone we are scanning matches the cached zone before considering
the cached node.
Deep thanks go to Andrea for many, many, many hours of hacking and testing
that went into cornering this bug.
Reported-by: Andrea Righi <andrea.righi@canonical.com> Tested-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_XEN_BALLOON_MEMORY_HOTPLUG is not defined
reserve_additional_memory() will set balloon_stats.target_pages to a
wrong value in case there are still some ballooned pages allocated via
alloc_xenballooned_pages().
This will result in balloon_process() no longer be triggered when
ballooned pages are freed in batches.
Reported-by: Nicholas Tsirakis <niko.tsirakis@gmail.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Objects allocated by xen_blkif_alloc come from the 'blkif_cache' kmem
cache. This cache is destoyed when xen-blkif is unloaded so it is
necessary to wait for the deferred free routine used for such objects to
complete. This necessity was missed in commit 14855954f636 "xen-blkback:
allow module to be cleanly unloaded". This patch fixes the problem by
taking/releasing extra module references in xen_blkif_alloc/free()
respectively.
Signed-off-by: Paul Durrant <pdurrant@amazon.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some QPs (e.g. XRC QP) are not tracked in kernel, in this case they have
an invalid res and should not be bound to any dynamically-allocated
counter in auto mode.
The s390 CPU Measurement sampling facility has an overflow condition
which fires when all entries in a SBD are used.
The measurement alert interrupt is triggered and reads out all samples
in this SDB. It then tests the successor SDB, if this SBD is not full,
the interrupt handler does not read any samples at all from this SDB
The design waits for the hardware to fill this SBD and then trigger
another meassurement alert interrupt.
This scheme works nicely until
an perf_event_overflow() function call discards the sample due to
a too high sampling rate.
The interrupt handler has logic to read out a partially filled SDB
when the perf event overflow condition in linux common code is met.
This causes the CPUM sampling measurement hardware and the PMU
device driver to operate on the same SBD's trailer entry.
This should not happen.
This can be seen here using this trace:
cpumsf_pmu_add: tear:0xb5286000
hw_perf_event_update: sdbt 0xb5286000 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 1. interrupt
hw_perf_event_update: sdbt 0xb5286008 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 2. interrupt
... this goes on fine until...
hw_perf_event_update: sdbt 0xb5286068 full 1 over 0 flush_all:0
perf_push_sample1: overflow
one or more samples read from the IRQ handler are rejected by
perf_event_overflow() and the IRQ handler advances to the next SDB
and modifies the trailer entry of a partially filled SDB.
hw_perf_event_update: sdbt 0xb5286070 full 0 over 0 flush_all:1
timestamp: 14:32:52.519953
Next time the IRQ handler is called for this SDB the trailer entry shows
an overflow count of 19 missed entries.
hw_perf_event_update: sdbt 0xb5286070 full 1 over 19 flush_all:1
timestamp: 14:32:52.970058
Remove access to a follow on SDB when event overflow happened.
Function perf_event_ever_overflow() and perf_event_account_interrupt()
are called every time samples are processed by the interrupt handler.
However function perf_event_account_interrupt() has checks to avoid being
flooded with interrupts (more then 1000 samples are received per
task_tick). Samples are then dropped and a PERF_RECORD_THROTTLED is
added to the perf data. The perf subsystem limit calculation is:
maximum sample frequency := 100000 --> 1 samples per 10 us
task_tick = 10ms = 10000us --> 1000 samples per task_tick
The work flow is
measurement_alert() uses SDBT head and each SBDT points to 511
SDB pages, each with 126 sample entries. After processing 8 SBDs
and for each valid sample calling:
there is a considerable amount of samples being dropped, especially when
the sample frequency is very high and near the 100000 limit.
To avoid the high amount of samples being dropped near the end of a
task_tick time frame, increment the sampling interval in case of
dropped events. The CPU Measurement sampling facility on the s390
supports only intervals, specifiing how many CPU cycles have to be
executed before a sample is generated. Increase the interval when the
samples being generated hit the task_tick limit.
With commit 6ce220dd2f8ea71d6afc29b9a7524c12e39f374a ("raid5: don't set
STRIPE_HANDLE to stripe which is in batch list"), we don't want to set
STRIPE_HANDLE flag for sh which is already in batch list.
However, the stripe which is the head of batch list should set this flag,
otherwise panic could happen inside init_stripe at BUG_ON(sh->batch_head),
it is reproducible with raid5 on top of nvdimm devices per Xiao oberserved.
Thanks for Xiao's effort to verify the change.
Fixes: 6ce220dd2f8ea ("raid5: don't set STRIPE_HANDLE to stripe which is in batch list") Reported-by: Xiao Ni <xni@redhat.com> Tested-by: Xiao Ni <xni@redhat.com> Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the lookup method on the dynamic root directory such that creation
calls, such as mkdir, open(O_CREAT), symlink, etc. fail with EOPNOTSUPP
rather than failing with some odd error (such as EEXIST).
lookup() itself tries to create automount directories when it is invoked.
These are cached locally in RAM and not committed to storage.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each AFS mountpoint has strings that define the target to be mounted. This
is required to end in a dot that is supposed to be stripped off. The
string can include suffixes of ".readonly" or ".backup" - which are
supposed to come before the terminal dot. To add to the confusion, the "fs
lsmount" afs utility does not show the terminal dot when displaying the
string.
The kernel mount source string parser, however, assumes that the terminal
dot marks the suffix and that the suffix is always "" and is thus ignored.
In most cases, there is no suffix and this is not a problem - but if there
is a suffix, it is lost and this affects the ability to mount the correct
volume.
The command line mount command, on the other hand, is expected not to
include a terminal dot - so the problem doesn't arise there.
Fix this by making sure that the dot exists and then stripping it when
passing the string to the mount configuration.
Fixes: bec5eb614130 ("AFS: Implement an autocell mount capability [ver #2]") Reported-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The socket read/write helpers only look at the file O_NONBLOCK. not
the iocb IOCB_NOWAIT flag. This breaks users like preadv2/pwritev2
and io_uring that rely on not having the file itself marked nonblocking,
but rather the iocb itself.
Cc: netdev@vger.kernel.org Acked-by: David Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Gadget driver should always use config_ep_by_speed() to initialize
usb_ep struct according to usb device's operating speed. Otherwise,
usb_ep struct may be wrong if usb devcie's operating speed is changed.
The key point in this patch is that we want to make sure the desc pointer
in usb_ep struct will be set to NULL when gadget is disconnected.
This will force it to call config_ep_by_speed() to correctly initialize
usb_ep struct based on the new operating speed when gadget is
re-connected later.
Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: EJ Hsu <ejh@nvidia.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Under certain circumstances, encoder atomic_check() can be entered
without adjusted_mode having been reset to the same as mode, which
confuses the scaling logic and can lead to a misprogrammed display.
Fix this by checking against the user-provided mode directly.
We do not support atomic modesetting on pre-nv50 hardware, but until now
our connector code was setting drm_connector->state on pre-nv50 hardware.
This causes the core to enter atomic modesetting paths in at least:
1. drm_connector_get_encoder(), returning connector->state->best_encoder
which is always 0, causing us to always report 0 as encoder_id in
the drmModeConnector struct returned by drmModeGetConnector().
2. drm_encoder_get_crtc(), returning NULL because uses_atomic get set,
causing us to always report 0 as crtc_id in the drmModeEncoder struct
returned by drmModeGetEncoder()
Which in turn confuses userspace, at least plymouth thinks that the pipe
has changed because of this and tries to reconfigure it unnecessarily.
More in general we should not set drm_connector->state in the non-atomic
code as this violates the drm-core's expectations.
This commit fixes this by using a nouveau_conn_atom struct embedded in the
nouveau_connector struct for property handling in the non-atomic case.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1706557 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Place the declaration of struct nouveau_conn_atom above that of
struct nouveau_connector. This commit makes no changes to the moved
block what so ever, it just moves it up a bit.
This is a preparation patch to fix some issues with connector handling
on pre nv50 displays (which do not use atomic modesetting).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In iscsi_if_rx func, after receiving one request through
iscsi_if_recv_msg func, iscsi_if_send_reply will be called to try to
reply to the request in a do-while loop. If the iscsi_if_send_reply
function keeps returning -EAGAIN, a deadlock will occur.
For example, a client only send msg without calling recvmsg func, then
it will result in the watchdog soft lockup. The details are given as
follows:
The discovering of sas port is driven by workqueue in libsas. When libsas
is processing port events or phy events in workqueue, new events may rise
up and change the state of some structures such as asd_sas_phy. This may
cause some problems such as follows:
==>thread 1 ==>thread 2
==>phy up
==>phy_up_v3_hw()
==>oob_mode = SATA_OOB_MODE;
==>phy down quickly
==>hisi_sas_phy_down()
==>sas_ha->notify_phy_event()
==>sas_phy_disconnected()
==>oob_mode = OOB_NOT_CONNECTED
==>workqueue wakeup
==>sas_form_port()
==>sas_discover_domain()
==>sas_get_port_device()
==>oob_mode is OOB_NOT_CONNECTED and device
is wrongly taken as expander
This at last lead to the panic when libsas trying to issue a command to
discover the device.
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Link: https://lore.kernel.org/r/20191206011118.46909-1-yanaijie@huawei.com Reported-by: Gao Chuan <gaochuan4@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
PORT UPDATE asynchronous event is generated on the host that issues PLOGI
ELS (in the case of higher WWPN). In that case, the event shouldn't be
handled as it sets unwanted DPC flags (i.e. LOOP_RESYNC_NEEDED) that
trigger link flap.
Ignore the event if the host has higher WWPN, but handle otherwise.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-13-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qla2x00_configure_local_loop sets RELOGIN_NEEDED bit and calls
qla24xx_fcport_handle_login to perform the login. This bit triggers a wake
up of DPC later after a successful login.
The deferred call is not needed if login succeeds, and it's set in
qla24xx_fcport_handle_login in case of errors, hence it should be safe to
drop.
Link: https://lore.kernel.org/r/20191125165702.1013-12-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Acked-by: Quinn Tran <qutran@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qlt_handle_login schedules session for deletion even if a login is in
progress. That causes login bouncing, i.e. a few logins are made before it
settles down.
Complete the first login by sending Notify Acknowledge IOCB via
qlt_plogi_ack_unref if the session is pending login completion.
Fixes: 9cd883f07a54 ("scsi: qla2xxx: Fix session cleanup for N2N") Cc: Krishna Kant <krishna.kant@purestorage.com> Cc: Alexei Potashnik <alexei@purestorage.com> Link: https://lore.kernel.org/r/20191125165702.1013-11-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad099074 ("scsi: qla2xxx: Fix N2N link re-connect") Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The size of the buffer is hardcoded as 0x70 or 112 bytes, while the size of
ELS IOCB is 0x40 and the size of PLOGI payload returned by Get Parameters
command is 0x74.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-9-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
MBA_PORT_UPDATE generates duplicate log lines in target mode because
qlt_async_event is called twice. Drop the calls within the case as the
function will be called right after the switch statement.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-8-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvel.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
del_work is already initialized inside qla2x00_alloc_fcport, there's no
need to overwrite it. Indeed, it might prevent complete traversal of
workqueue list.
Fixes: a01c77d2cbc45 ("scsi: qla2xxx: Move session delete to driver work queue") Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-5-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Target makes implicit LOGO on session teardown. LOGO ELS is not send on the
wire and initiator is not aware that target no longer wants talking to
it. Initiator keeps sending I/O requests, target responds with BA_RJT, they
time out and then initiator sends ABORT TASK (ABTS-LS).
Current behaviour incurs unneeded I/O timeout and can be fixed for some
initiators by making explicit LOGO on session deletion.
Link: https://lore.kernel.org/r/20191125165702.1013-3-r.bolshakov@yadro.com Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If RoCE PDUs being sent or received contain pad bytes, then the iCRC
is miscalculated, resulting in PDUs being emitted by RXE with an incorrect
iCRC, as well as ingress PDUs being dropped due to erroneously detecting
a bad iCRC in the PDU. The fix is to include the pad bytes, if any,
in iCRC computations.
Note: This bug has caused broken on-the-wire compatibility with actual
hardware RoCE devices since the soft-RoCE driver was first put into the
mainstream kernel. Fixing it will create an incompatibility with the
original soft-RoCE devices, but is necessary to be compatible with real
hardware devices.
Make the AFS dynamic root superblock R/W so that SELinux can set the
security label on it. Without this, upgrades to, say, the Fedora
filesystem-afs RPM fail if afs is mounted on it because the SELinux label
can't be (re-)applied.
It might be better to make it possible to bypass the R/O check for LSM
label application through setxattr.
Fixes: 4d673da14533 ("afs: Support the AFS dynamic root") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: selinux@vger.kernel.org
cc: linux-security-module@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
afs_find_server tries to find a server that has an address that
matches the transport address of an rxrpc peer. The code assumes
that the transport address is always ipv6, with ipv4 represented
as ipv4 mapped addresses, but that's not the case. If the transport
family is AF_INET, srx->transport.sin6.sin6_addr.s6_addr32[] will
be beyond the actual ipv4 address and will always be 0, and all
ipv4 addresses will be seen as matching.
As a result, the first ipv4 address seen on any server will be
considered a match, and the server returned may be the wrong one.
One of the consequences is that callbacks received over ipv4 will
only be correctly applied for the server that happens to have the
first ipv4 address on the fs_addresses4 list. Callbacks over ipv4
from all other servers are dropped, causing the client to serve stale
data.
This is fixed by looking at the transport family, and comparing ipv4
addresses based on a sockaddr_in structure rather than a sockaddr_in6.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Right now devfreq_dev_release will print a warning and abort the rest of
the cleanup if the devfreq instance is not part of the global
devfreq_list. But this is a valid scenario, for example it can happen if
the governor can't be found or on any other init error that happens
after device_register.
Initialize devfreq->node to an empty list head in devfreq_add_device so
that list_del becomes a safe noop inside devfreq_dev_release and we can
continue the rest of the cleanup.
The devfreq_notifier_call functions will update scaling_min_freq and
scaling_max_freq when the OPP table is updated.
If fetching the maximum frequency fails then scaling_max_freq remains
set to zero which is confusing. Set to ULONG_MAX instead so we don't
need special handling for this case in other places.
As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
If nvme.write_queues equals the number of CPUs, the driver had decreased
the number of interrupts available such that there could only be one read
queue even if the controller could support more. Remove the interrupt
count reduction in this case. The driver wouldn't request more IRQs than
it wants queues anyway.
The number of poll or write queues should never be negative. Use unsigned
types so that it's not possible to break have the driver not allocate
any queues.
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
During mode transition steer fifo could overflow. Quite often it
recovers by itself, but sometimes it doesn't.
[how]
Add steer fifo reset before unblanking the stream. Also add a short
delay when resetting dig resync fifo to make sure register writes
don't end up back-to-back, in which case the HW might miss the reset
request.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When security violation from new vbios happens, data fabric is
risky to stop working. So prevent the direct access to DF
mmFabricConfigAccessControl from the new vbios and onwards.
If an error occurs on one of the ios used for creating an
association, the creating routine has error paths that are
invoked by the command failure and the error paths will free
up the controller resources created to that point.
But... the io was ultimately determined by an asynchronous
completion routine that detected the error and which
unconditionally invokes the error_recovery path which calls
delete_association. Delete association deletes all outstanding
io then tears down the controller resources. So the
create_association thread can be running in parallel with
the error_recovery thread. What was seen was the LLDD received
a call to delete a queue, causing the LLDD to do a free of a
resource, then the transport called the delete queue again
causing the driver to repeat the free call. The second free
routine corrupted the allocator. The transport shouldn't be
making the duplicate call, and the delete queue is just one
of the resources being freed.
To fix, it is realized that the create_association path is
completely serialized with one command at a time. So the
failed io completion will always be seen by the create_association
path and as of the failure, there are no ios to terminate and there
is no reason to be manipulating queue freeze states, etc.
The serialized condition stays true until the controller is
transitioned to the LIVE state. Thus the fix is to change the
error recovery path to check the controller state and only
invoke the teardown path if not already in the CONNECTING state.
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In nvme-fc: it's possible to have connected active controllers
and as no references are taken on the LLDD, the LLDD can be
unloaded. The controller would enter a reconnect state and as
long as the LLDD resumed within the reconnect timeout, the
controller would resume. But if a namespace on the controller
is the root device, allowing the driver to unload can be problematic.
To reload the driver, it may require new io to the boot device,
and as it's no longer connected we get into a catch-22 that
eventually fails, and the system locks up.
Fix this issue by taking a module reference for every connected
controller (which is what the core layer did to the transport
module). Reference is cleared when the controller is removed.
Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "panel" pointer is not reset to NULL if of_drm_find_panel()
returns an error. Therefore we later assume that a panel was found,
and try to dereference the error pointer, resulting in:
mcde-dsi a0351000.dsi: failed to find panel try bridge (4294966779)
Unable to handle kernel paging request at virtual address fffffe03
PC is at drm_panel_bridge_add.part.0+0x10/0x5c
LR is at mcde_dsi_bind+0x120/0x464
...
Reset "panel" to NULL to avoid this problem.
Also change the format string of the error to %ld to print
the negative errors correctly. The crash above then becomes:
mcde-dsi a0351000.dsi: failed to find panel try bridge (-517)
mcde-dsi a0351000.dsi: no panel or bridge
...
The problem is the check introduced to for_each_hstate() loop that
should skip default_hstate_idx. Since it doesn't update 'i' counter,
all subsequent huge page sizes are skipped as well.
Fixes: 8fc312b32b25 ("mm/hugetlbfs: fix error handling when setting up mounts") Signed-off-by: Jan Stancek <jstancek@redhat.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch implemented an incomplete workaround of erratum
A-008171. The complete workaround is as below. This patch is to
implement the complete workaround which uses SW tuning if HW tuning
fails, and retries both HW/SW tuning once with reduced clock if
workaround fails. This is suggested by hardware team, and the patch
had been verified on LS1046A eSDHC + Phison 32G eMMC which could
trigger the erratum.
Workaround:
/* For T1040, T2080, LS1021A, T1023 Rev 1: */
1. Program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO.
2. Program TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
3. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
4. Set SYSCTL2[EXTN] and SYSCTL2[SAMPCLKSEL].
5. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
6. Wait for IRQSTAT[BRR], buffer read ready, to be set.
7. Clear IRQSTAT[BRR].
8. Check SYSCTL2[EXTN] to be cleared.
9. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0: */
1. Read the TBCTL[31:0] register. Write TBCTL[11:8]=4'h8 and wait for
1ms.
2. Read the TBCTL[31:0] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[31:0] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[15:8]-TBSTAT[7:0] > 4*DIV_RATIO or TBSTAT[7:0]-TBSTAT[15:8]
> 4*DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] = 4*DIV_RATIO and
program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1012A Rev1, LS1043A Rev 1.x, LS1046A 1.0: */
1. Read the TBCTL[0:31] register. Write TBCTL[20:23]=4'h8 and wait for
1ms.
2. Read the TBCTL[0:31] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[0:31] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[16:23]-TBSTAT[24:31] > 4*DIV_RATIO or TBSTAT[24:31]-
TBSTAT[16:23] > 4* DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] =
4*DIV_RATIO and program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0 LS1012A Rev1,
* LS1043A Rev 1.x, LS1046A 1.0:
*/
5. else program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO and program
TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
6. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
7. Set SYSCTL2[EXTN], wait 1us and SYSCTL2[SAMPCLKSEL].
8. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
9. Wait for IRQSTAT[BRR], buffer read ready, to be set.
10. Clear IRQSTAT[BRR].
11. Check SYSCTL2[EXTN] to be cleared.
12. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
When we receive a new packet from the guest, we check if the
src_cid is correct, but we forgot to check the dst_cid.
The host should accept only packets where dst_cid is
equal to the host CID.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In netpoll the napi handler could be called with budget equal to zero.
Current ENA napi handler doesn't take that into consideration.
The napi handler handles Rx packets in a do-while loop.
Currently, the budget check happens only after decrementing the
budget, therefore the napi handler, in rare cases, could run over
MAX_INT packets.
In addition to that, this moves all budget related variables to int
calculation and stop mixing u32 to avoid ambiguity
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for
doit handlers") we add strict check for inet6_rtm_getaddr(). But we did
the invalid header values check before checking if NETLINK_F_STRICT_CHK
is set. This may break backwards compatibility if user already set the
ifm->ifa_prefixlen, ifm->ifa_flags, ifm->ifa_scope in their netlink code.
I didn't move the nlmsg_len check because I thought it's a valid check.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for doit handlers") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock. It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.
Fix by applying the corrected clamp value.
Fixes: 74706afa712d ("bnxt_en: Update interrupt coalescing logic.") Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GTP RX packet path lookups pdp context with TID. If duplicate TID pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, TID value should be unique.
GTP TX packet path lookups pdp context with ms_addr. If duplicate ms_addr pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, ms_addr value should be unique.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipv4_pdp_find() is called in TX packet path of GTP.
ipv4_pdp_find() internally uses gtp->tid_hash to lookup pdp context.
In the current code, gtp->tid_hash and gtp->addr_hash are freed by
->dellink(), which is gtp_dellink().
But gtp_dellink() would be called while packets are processing.
So, gtp_dellink() should not free gtp->tid_hash and gtp->addr_hash.
Instead, dev->priv_destructor() would be used because this callback
is called after all packet processing safely.
Test commands:
ip link add veth1 type veth peer name veth2
ip a a 172.0.0.1/24 dev veth1
ip link set veth1 up
ip a a 172.99.0.1/32 dev lo
gtp-link add gtp1 &
gtp-tunnel add gtp1 v1 200 100 172.99.0.2 172.0.0.2
ip r a 172.99.0.2/32 dev gtp1
ip link set gtp1 mtu 1500
ip netns add ns2
ip link set veth2 netns ns2
ip netns exec ns2 ip a a 172.0.0.2/24 dev veth2
ip netns exec ns2 ip link set veth2 up
ip netns exec ns2 ip a a 172.99.0.2/32 dev lo
ip netns exec ns2 ip link set lo up
ip netns exec ns2 gtp-link add gtp2 &
ip netns exec ns2 gtp-tunnel add gtp2 v1 100 200 172.99.0.1 172.0.0.1
ip netns exec ns2 ip r a 172.99.0.1/32 dev gtp2
ip netns exec ns2 ip link set gtp2 mtu 1500
Host can provide send indirection table messages anytime after RSS is
enabled by calling rndis_filter_set_rss_param(). So the host provided
table values may be overwritten by the initialization in
rndis_set_subchannel().
To prevent this problem, move the tx_table initialization before calling
rndis_filter_set_rss_param().
Fixes: a6fb6aa3cfa9 ("hv_netvsc: Set tx_table to equal weight after subchannels open") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Kubecek and Firo Yang did a very nice analysis of crashes
happening in __inet_lookup_established().
Since a TCP socket can go from TCP_ESTABLISH to TCP_LISTEN
(via a close()/socket()/listen() cycle) without a RCU grace period,
I should not have changed listeners linkage in their hash table.
They must use the nulls protocol (Documentation/RCU/rculist_nulls.txt),
so that a lookup can detect a socket in a hash list was moved in
another one.
Since we added code in commit d296ba60d8e2 ("soreuseport: Resolve
merge conflict for v4/v6 ordering fix"), we have to add
hlist_nulls_add_tail_rcu() helper.
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Michal Kubecek <mkubecek@suse.cz> Reported-by: Firo Yang <firo.yang@suse.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Link: https://lore.kernel.org/netdev/20191120083919.GH27852@unicorn.suse.cz/ Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Backport of commit fdfc5c8594c2 ("tcp: remove empty skb from
write queue in error cases") in linux-4.14 stable triggered
various bugs. One of them has been fixed in commit ba2ddb43f270
("tcp: Don't dequeue SYN/FIN-segments from write-queue"), but
we still have crashes in some occasions.
Root-cause is that when tcp_sendmsg() has allocated a fresh
skb and could not append a fragment before being blocked
in sk_stream_wait_memory(), tcp_write_xmit() might be called
and decide to send this fresh and empty skb.
Sending an empty packet is not only silly, it might have caused
many issues we had in the past with tp->packets_out being
out of sync.
Fixes: c65f7f00c587 ("[TCP]: Simplify SKB data portion allocation with NETIF_F_SG.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Christoph Paasch <cpaasch@apple.com> Acked-by: Neal Cardwell <ncardwell@google.com> Cc: Jason Baron <jbaron@akamai.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the recent fix in commit 1899bb325149 ("bonding: fix state
transition issue in link monitoring"), the active-backup mode with
miimon initially come-up fine but after a link-failure, both members
transition into backup state.
Following steps to reproduce the scenario (eth1 and eth2 are the
slaves of the bond):
ip link set eth1 up
ip link set eth2 down
sleep 1
ip link set eth2 up
ip link set eth1 down
cat /sys/class/net/eth1/bonding_slave/state
cat /sys/class/net/eth2/bonding_slave/state
Fixes: 1899bb325149 ("bonding: fix state transition issue in link monitoring") CC: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GTP default hashtable size is 1024 and userspace could set specific
hashtable size with IFLA_GTP_PDP_HASHSIZE. If hashtable size is set to 0
from userspace, hashtable will not work and panic will occur.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gtp_genl_dump_pdp() is ->dumpit() callback of GTP module and it is used
to dump pdp contexts. it would be re-executed because of dump packet size.
If dump packet size is too big, it saves current dump pointer
(gtp interface pointer, bucket, TID value) then it restarts dump from
last pointer.
Current GTP code allows adding zero TID pdp context but dump code
ignores zero TID value. So, last dump pointer will not be found.
In addition, this patch adds missing rcu_read_lock() in
gtp_genl_dump_pdp().
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
phylink requires the MAC to report when its link status changes when
operating in inband modes. Failure to report link status changes
means that phylink has no idea when the link events happen, which
results in either the network interface's carrier remaining up or
remaining permanently down.
For example, with a fiber module, if the interface is brought up and
link is initially established, taking the link down at the far end
will cut the optical power. The SFP module's LOS asserts, we
deactivate the link, and the network interface reports no carrier.
When the far end is brought back up, the SFP module's LOS deasserts,
but the MAC may be slower to establish link. If this happens (which
in my tests is a certainty) then phylink never hears that the MAC
has established link with the far end, and the network interface is
stuck reporting no carrier. This means the interface is
non-functional.
Avoiding the link interrupt when we have phylink is basically not
an option, so remove the !port->phylink from the test.
Fixes: 4bb043262878 ("net: mvpp2: phylink support") Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
So disable the neigh confirm for vxlan and geneve pmtu update.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: a93bf0ff4490 ("vxlan: update skb dst pmtu on tx path") Fixes: 52a589d51f10 ("geneve: update skb dst pmtu on tx path") Reviewed-by: Guillaume Nault <gnault@redhat.com> Tested-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although vti and vti6 are immune to this problem because they are IFF_NOARP
interfaces, as Guillaume pointed. There is still no sense to confirm neighbour
here.
v5: Update commit description.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No Change.
v4: Update commit description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 0dec879f636f ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP") Reviewed-by: Guillaume Nault <gnault@redhat.com> Tested-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
