Unit testing this in VKMS shows that passing 0 into
this function returns -1, which is highly counter-
intuitive. Fix it by checking whether the input is
>= 0 instead of > 0.
Fixes: 64566b5e767f ("drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil") Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Simon Ser <contact@emersion.fr> Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231108163647.106853-2-harry.wentland@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller wants the difference between *total and *sync_start in the
HDMI_VIDEO_EXT_*DELAY registers. Otherwise the signal is very unstable for
certain non-VIC modes. See downstream commit [0].
Asus Transformer TF700T is a Tegra30 tablet device which uses RGB->DSI
bridge that requires a precise clock rate in order to operate properly.
Tegra30 has a dedicated PLL for each display controller, hence the PLL
rate can be changed freely. Allow PLL rate changes on Tegra30+ for RGB
output. Configure the clock rate before display controller is enabled
since DC itself may be running off this PLL and it's not okay to change
the rate of the active PLL that doesn't support dynamic frequency
switching since hardware will hang.
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Stable-dep-of: 830c1ded3563 ("drm/tegra: dsi: Fix some error handling paths in tegra_dsi_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable function increases the power disable depth,
which means that we must perform a matching decrement on the error
handling path to maintain balance within the given context.
Additionally, we need to address the same issue for pm_runtime_get_sync.
We fix this by invoking pm_runtime_disable and pm_runtime_put_sync
when error returns.
The DPAUX hardware block exposes an DP AUX interface that provides
access to an AUX bus and the devices on that bus. Use the DP AUX bus
infrastructure that was recently introduced to probe devices on this
bus from DT.
There is this reported crash when experimenting with the lvm2 testsuite.
The list corruption is caused by the fact that the postsuspend and resume
methods were not paired correctly; there were two consecutive calls to the
origin_postsuspend function. The second call attempts to remove the
"hash_list" entry from a list, while it was already removed by the first
call.
Fix __dm_internal_resume so that it calls the preresume and resume
methods of the table's targets.
If a preresume method of some target fails, we are in a tricky situation.
We can't return an error because dm_internal_resume isn't supposed to
return errors. We can't return success, because then the "resume" and
"postsuspend" methods would not be paired correctly. So, we set the
DMF_SUSPENDED flag and we fake normal suspend - it may confuse userspace
tools, but it won't cause a kernel crash.
An empty flush doesn't have a payload, so it should never be looked at
when considering to possibly requeue a bio for the case when a reshape
is in progress.
Fixes: 9dbd1aa3a81c ("dm raid: add reshaping support to the target") Reported-by: Patrick Plenefisch <simonpatp@gmail.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d031140 ("nfp: flower: monitor and offload LAG groups") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 3557baabf280 ("[L2TP]: PPP over L2TP driver core") Reviewed-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'olr' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'olr' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to the earlier patch that changes sk_getsockopt() to
take the sockptr_t argument. This patch also changes
do_ip_getsockopt() to take the sockptr_t argument such that
a latter patch can make bpf_getsockopt(SOL_IP) to reuse
do_ip_getsockopt().
Note on the change in ip_mc_gsfget(). This function is to
return an array of sockaddr_storage in optval. This function
is shared between ip_get_mcast_msfilter() and
compat_ip_get_mcast_msfilter(). However, the sockaddr_storage
is stored at different offset of the optval because of
the difference between group_filter and compat_group_filter.
Thus, a new 'ss_offset' argument is added to ip_mc_gsfget().
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/r/20220902002828.2890585-1-kafai@fb.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 5c3be3e0eb44 ("ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt() function") Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch changes sk_getsockopt() to take the sockptr_t argument
such that it can be used by bpf_getsockopt(SOL_SOCKET) in a
latter patch.
security_socket_getpeersec_stream() is not changed. It stays
with the __user ptr (optval.user and optlen.user) to avoid changes
to other security hooks. bpf_getsockopt(SOL_SOCKET) also does not
support SO_PEERSEC.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/r/20220902002802.2888419-1-kafai@fb.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 5c3be3e0eb44 ("ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt() function") Signed-off-by: Sasha Levin <sashal@kernel.org>
A latter patch refactors bpf_getsockopt(SOL_SOCKET) with the
sock_getsockopt() to avoid code duplication and code
drift between the two duplicates.
The current sock_getsockopt() takes sock ptr as the argument.
The very first thing of this function is to get back the sk ptr
by 'sk = sock->sk'.
bpf_getsockopt() could be called when the sk does not have
the sock ptr created. Meaning sk->sk_socket is NULL. For example,
when a passive tcp connection has just been established but has yet
been accept()-ed. Thus, it cannot use the sock_getsockopt(sk->sk_socket)
or else it will pass a NULL ptr.
This patch moves all sock_getsockopt implementation to the newly
added sk_getsockopt(). The new sk_getsockopt() takes a sk ptr
and immediately gets the sock ptr by 'sock = sk->sk_socket'
The existing sock_getsockopt(sock) is changed to call
sk_getsockopt(sock->sk). All existing callers have both sock->sk
and sk->sk_socket pointer.
The latter patch will make bpf_getsockopt(SOL_SOCKET) call
sk_getsockopt(sk) directly. The bpf_getsockopt(SOL_SOCKET) does
not use the optnames that require sk->sk_socket, so it will
be safe.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/r/20220902002756.2887884-1-kafai@fb.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 5c3be3e0eb44 ("ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt() function") Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the kernel isn't built with interconnect support, icc_get_name()
returns NULL and we get following warning:
drivers/opp/debugfs.c: In function 'bw_name_read':
drivers/opp/debugfs.c:43:42: error: '%.62s' directive argument is null [-Werror=format-overflow=]
i = scnprintf(buf, sizeof(buf), "%.62s\n", icc_get_name(path));
Fix it.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402141313.81ltVF5g-lkp@intel.com/ Fixes: 0430b1d5704b0 ("opp: Expose bandwidth information via debugfs") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay") Signed-off-by: Tim Pambor <tp@osasysteme.de> Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RGMII mode can be enable from dp83822 straps, and also writing bit 9
of register 0x17 - RMII and Status Register (RCSR).
When phy_interface_is_rgmii rgmii mode must be enabled, same for
contrary, this prevents malconfigurations of hw straps
Currently, the mac port is fixed to configured as full dplex mode in
hclge_mac_init() when driver initialization or reset restore. Users may
change the mode to half duplex with ethtool, so it may cause the user
configuration dropped after reset.
To fix it, don't change the duplex mode when resetting.
Fixes: 2d03eacc0b7e ("net: hns3: Only update mac configuation when necessary") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HIP08 devices does not register the ptp devices, so the
hdev->ptp is NULL, but the hardware can receive 1588 messages,
and set the HNS3_RXD_TS_VLD_B bit, so, if match this case, the
access of hdev->ptp->flags will cause a kernel crash:
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay") Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
8d975c15c0cd ("ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()") 1ca1ba465e55 ("geneve: make sure to pull inner header in geneve_rx()")
We have to save skb->network_header in a temporary variable
in order to be able to recompute the network_header pointer
after a pskb_inet_may_pull() call.
pskb_inet_may_pull() makes sure the needed headers are in skb->head.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When rule policy is changed, ipv6 socket cache is not refreshed.
The sock's skb still uses a outdated route cache and was sent to
a wrong interface.
To avoid this error we should update fib node's version when
rule is changed. Then skb's route will be reroute checked as
route cache version is already different with fib node version.
The route cache is refreshed to match the latest rule.
Fixes: 101367c2f8c4 ("[IPV6]: Policy Routing Rules") Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com> Signed-off-by: Lena Wang <lena.wang@mediatek.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The stackmap code relies on roundup_pow_of_two() to compute the number
of hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code.
The commit in the fixes tag actually attempted to fix this, but the fix
did not account for the UB, so the fix only works on CPUs where an
overflow does result in a neat truncation to zero, which is not
guaranteed. Checking the value before rounding does not have this
problem.
Fixes: 6183f4d3a0a2 ("bpf: Check for integer overflow when using roundup_pow_of_two()") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-ID: <20240307120340.99577-4-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hashtab code relies on roundup_pow_of_two() to compute the number of
hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code. So apply the same
fix to hashtab, by moving the overflow check to before the roundup.
Fixes: daaf427c6ab3 ("bpf: fix arraymap NULL deref and missing overflow and zero size checks") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-3-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devmap code allocates a number hash buckets equal to the next power
of two of the max_entries value provided when creating the map. When
rounding up to the next power of two, the 32-bit variable storing the
number of buckets can overflow, and the code checks for overflow by
checking if the truncated 32-bit value is equal to 0. However, on 32-bit
arches the rounding up itself can overflow mid-way through, because it
ends up doing a left-shift of 32 bits on an unsigned long value. If the
size of an unsigned long is four bytes, this is undefined behaviour, so
there is no guarantee that we'll end up with a nice and tidy 0-value at
the end.
Syzbot managed to turn this into a crash on arm32 by creating a
DEVMAP_HASH with max_entries > 0x80000000 and then trying to update it.
Fix this by moving the overflow check to before the rounding up
operation.
Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index") Link: https://lore.kernel.org/r/000000000000ed666a0611af6818@google.com Reported-and-tested-by: syzbot+8cd36f6b65f3cafd400a@syzkaller.appspotmail.com Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-2-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
struct hci_dev_info has a fixed size name[8] field so in the event that
hdev->name is bigger than that strcpy would attempt to write past its
size, so this fixes this problem by switching to use strscpy.
Fixes: dcda165706b9 ("Bluetooth: hci_core: Fix build warnings") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.
Fixes: 6845667146a2 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.
Based on the assumption that this is similar to the wcn6750
Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Tested-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 56d074d26c58 ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The "pending connections" feature was originally introduced with commit 4c67bc74f016 ("[Bluetooth] Support concurrent connect requests") and 6bd57416127e ("[Bluetooth] Handling pending connect attempts after
inquiry") to handle controllers supporting only a single connection request
at a time. Later things were extended to also cancel ongoing inquiries on
connect() with commit 89e65975fea5 ("Bluetooth: Cancel Inquiry before
Create Connection").
With commit a9de9248064b ("[Bluetooth] Switch from OGF+OCF to using only
opcodes"), hci_conn_check_pending() was introduced as a helper to
consolidate a few places where we check for pending connections (indicated
by the BT_CONNECT2 flag) and then try to connect.
This refactoring commit also snuck in two more calls to
hci_conn_check_pending():
- One is in the failure callback of hci_cs_inquiry(), this one probably
makes sense: If we send an "HCI Inquiry" command and then immediately
after a "Create Connection" command, the "Create Connection" command might
fail before the "HCI Inquiry" command, and then we want to retry the
"Create Connection" on failure of the "HCI Inquiry".
- The other added call to hci_conn_check_pending() is in the event handler
for the "Remote Name" event, this seems unrelated and is possibly a
copy-paste error, so remove that one.
Fixes: a9de9248064b ("[Bluetooth] Switch from OGF+OCF to using only opcodes") Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b47b ("igb: enable internal PPS for the i210") Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove code duplication in the tsync interrupt handler function by moving
this logic to separate functions. This keeps the interrupt handler readable
and allows the new functions to be extended for adapter types other than
i210.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: ee14cc9ea19b ("igb: Fix missing time sync events") Signed-off-by: Sasha Levin <sashal@kernel.org>
For those endpoint devices connect to system via hotplug capable ports,
users could request a hot reset to the device by flapping device's link
through setting the slot's link control register, as pciehp_ist() DLLSC
interrupt sequence response, pciehp will unload the device driver and
then power it off. thus cause an IOMMU device-TLB invalidation (Intel
VT-d spec, or ATS Invalidation in PCIe spec r6.1) request for non-existence
target device to be sent and deadly loop to retry that request after ITE
fault triggered in interrupt context.
That would cause following continuous hard lockup warning and system hang
Such issue could be triggered by all kinds of regular surprise removal
hotplug operation. like:
1. pull EP(endpoint device) out directly.
2. turn off EP's power.
3. bring the link down.
etc.
this patch aims to work for regular safe removal and surprise removal
unplug. these hot unplug handling process could be optimized for fix the
ATS Invalidation hang issue by calling pci_dev_is_disconnected() in
function devtlb_invalidation_with_pasid() to check target device state to
avoid sending meaningless ATS Invalidation request to iommu when device is
gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)
For safe removal, device wouldn't be removed until the whole software
handling process is done, it wouldn't trigger the hard lock up issue
caused by too long ATS Invalidation timeout wait. In safe removal path,
device state isn't set to pci_channel_io_perm_failure in
pciehp_unconfigure_device() by checking 'presence' parameter, calling
pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will return
false there, wouldn't break the function.
For surprise removal, device state is set to pci_channel_io_perm_failure in
pciehp_unconfigure_device(), means device is already gone (disconnected)
call pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will
return true to break the function not to send ATS Invalidation request to
the disconnected device blindly, thus avoid to trigger further ITE fault,
and ITE fault will block all invalidation request to be handled.
furthermore retry the timeout request could trigger hard lockup.
Make pci_dev_is_disconnected() public so that it can be called from
Intel VT-d driver to quickly fix/workaround the surprise removal
unplug hang issue for those ATS capable devices on PCIe switch downstream
hotplug capable ports.
Beside pci_device_is_present() function, this one has no config space
space access, so is light enough to optimize the normal pure surprise
removal and safe removal flow.
Acked-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Tested-by: Haorong Ye <yehaorong@bytedance.com> Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> Link: https://lore.kernel.org/r/20240301080727.3529832-2-haifeng.zhao@linux.intel.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stable-dep-of: 4fc82cd907ac ("iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected") Signed-off-by: Sasha Levin <sashal@kernel.org>
The creds and oa->data need to be freed in the error-handling paths after
their allocation. So this patch add these deallocations in the
corresponding paths.
Fixes: 1d658336b05f ("SUNRPC: Add RPC based upcall mechanism for RPCGSS auth") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with CONFIG_XEN_PV=y, .text symbols are emitted into
the .notes section so that Xen can find the "startup_xen" entry point.
This information is used prior to booting the kernel, so relocations
are not useful. In fact, performing relocations against the .notes
section means that the KASLR base is exposed since /sys/kernel/notes
is world-readable.
To avoid leaking the KASLR base without breaking unprivileged tools that
are expecting to read /sys/kernel/notes, skip performing relocations in
the .notes section. The values readable in .notes are then identical to
those found in System.map.
It is generally invalid to fail a Device Check notification if the scan
handler has not been attached to the given device after a bus rescan,
because there may be valid reasons for the scan handler to refuse
attaching to the device (for example, the device is not ready).
For this reason, modify acpi_scan_device_check() to return 0 in that
case without printing a warning.
While at it, reduce the log level of the "already enumerated" message
in the same function, because it is only interesting when debugging
notification handling
Fixes: 443fc8202272 ("ACPI / hotplug: Rework generic code to handle suprise removals") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A known issue on some Zen laptops, keyboard stopped working due to commit 9946e39fe8d0 fael@kernel.org("ACPI: resource: skip IRQ override on AMD
Zen platforms") on kernel 5.19.10.
The ACPI IRQ override is required for this board due to buggy DSDT, thus
adding the board vendor and name to irq1_edge_low_force_override fixes
the issue.
Match order specified in binding documentation. It says "mem" should be
the last interrupt.
This fixes:
arch/arm64/boot/dts/marvell/armada-3720-db.dtb: crypto@90000: interrupt-names:0: 'ring0' was expected
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/armada-3720-db.dtb: crypto@90000: interrupt-names:1: 'ring1' was expected
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/armada-3720-db.dtb: crypto@90000: interrupt-names:2: 'ring2' was expected
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/armada-3720-db.dtb: crypto@90000: interrupt-names:3: 'ring3' was expected
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/armada-3720-db.dtb: crypto@90000: interrupt-names:4: 'eip' was expected
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/armada-3720-db.dtb: crypto@90000: interrupt-names:5: 'mem' was expected
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch") Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
All Ethernet AVB instances on R-Car V3U have registers related to UDP/IP
support, but the declared register blocks for the first two instances
are too small to cover them.
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence update the compatible properties in various device nodes
to include family-specific compatible values for R-Car Gen4 instead of
R-Car Gen3:
- DMAC,
- (H)SCIF,
- I2C,
- IPMMU,
- WDT.
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Avoid the following warnings by removing the ena_select_queue() function
and rely on the net core to do the queue selection, The issue happen
when an skb received from an interface with more queues than ena is
forwarded to the ena interface.
[ 1176.159959] eth0 selects TX queue 11, but real number of TX queues is 8
[ 1176.863976] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1180.767877] eth0 selects TX queue 14, but real number of TX queues is 8
[ 1188.703742] eth0 selects TX queue 14, but real number of TX queues is 8
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Kamal Heib <kheib@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On many systems that have an AMD IOMMU the following sequence of
warnings is observed during bootup.
```
pci 0000:00:00.2 can't derive routing for PCI INT A
pci 0000:00:00.2: PCI INT A: not connected
```
This series of events happens because of the IOMMU initialization
sequence order and the lack of _PRT entries for the IOMMU.
During initialization the IOMMU driver first enables the PCI device
using pci_enable_device(). This will call acpi_pci_irq_enable()
which will check if the interrupt is declared in a PCI routing table
(_PRT) entry. According to the PCI spec [1] these routing entries
are only required under PCI root bridges:
The _PRT object is required under all PCI root bridges
The IOMMU is directly connected to the root complex, so there is no
parent bridge to look for a _PRT entry. The first warning is emitted
since no entry could be found in the hierarchy. The second warning is
then emitted because the interrupt hasn't yet been configured to any
value. The pin was configured in pci_read_irq() but the byte in
PCI_INTERRUPT_LINE return 0xff which means "Unknown".
After that sequence of events pci_enable_msi() is called and this
will allocate an interrupt.
That is both of these warnings are totally harmless because the IOMMU
uses MSI for interrupts. To avoid even trying to probe for a _PRT
entry mark the IOMMU as IRQ managed. This avoids both warnings.
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just Tegra210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes Tegra210 you don't get
this driver.
Fixes: 46a88534afb59 ("bus: Add support for Tegra ACONNECT") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix this by freeing the CPU idle device after unregistering it.
Fixes: 3d339dcbb56d ("cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
wilc_netdev_cleanup currently triggers a KASAN warning, which can be
observed on interface registration error path, or simply by
removing the module/unbinding device from driver:
==================================================================
BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc
Read of size 4 at addr c54d1ce8 by task sh/86
CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from print_report+0x154/0x500
print_report from kasan_report+0xac/0xd8
kasan_report from wilc_netdev_cleanup+0x508/0x5cc
wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec
wilc_bus_remove from spi_remove+0x8c/0xac
spi_remove from device_release_driver_internal+0x434/0x5f8
device_release_driver_internal from unbind_store+0xbc/0x108
unbind_store from kernfs_fop_write_iter+0x398/0x584
kernfs_fop_write_iter from vfs_write+0x728/0xf88
vfs_write from ksys_write+0x110/0x1e4
ksys_write from ret_fast_syscall+0x0/0x1c
David Mosberger-Tan initial investigation [1] showed that this
use-after-free is due to netdevice unregistration during vif list
traversal. When unregistering a net device, since the needs_free_netdev has
been set to true during registration, the netdevice object is also freed,
and as a consequence, the corresponding vif object too, since it is
attached to it as private netdevice data. The next occurrence of the loop
then tries to access freed vif pointer to the list to move forward in the
list.
Fix this use-after-free thanks to two mechanisms:
- navigate in the list with list_for_each_entry_safe, which allows to
safely modify the list as we go through each element. For each element,
remove it from the list with list_del_rcu
- make sure to wait for RCU grace period end after each vif removal to make
sure it is safe to free the corresponding vif too (through
unregister_netdev)
Since we are in a RCU "modifier" path (not a "reader" path), and because
such path is expected not to be concurrent to any other modifier (we are
using the vif_mutex lock), we do not need to use RCU list API, that's why
we can benefit from list_for_each_entry_safe.
Currently tracing is supposed not to allow for bpf_spin_{lock,unlock}()
helper calls. This is to prevent deadlock for the following cases:
- there is a prog (prog-A) calling bpf_spin_{lock,unlock}().
- there is a tracing program (prog-B), e.g., fentry, attached
to bpf_spin_lock() and/or bpf_spin_unlock().
- prog-B calls bpf_spin_{lock,unlock}().
For such a case, when prog-A calls bpf_spin_{lock,unlock}(),
a deadlock will happen.
The related source codes are below in kernel/bpf/helpers.c:
notrace BPF_CALL_1(bpf_spin_lock, struct bpf_spin_lock *, lock)
notrace BPF_CALL_1(bpf_spin_unlock, struct bpf_spin_lock *, lock)
notrace is supposed to prevent fentry prog from attaching to
bpf_spin_{lock,unlock}().
But actually this is not the case and fentry prog can successfully
attached to bpf_spin_lock(). Siddharth Chintamaneni reported
the issue in [1]. The following is the macro definition for
above BPF_CALL_1:
#define BPF_CALL_x(x, name, ...) \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
typedef u64 (*btf_##name)(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)) \
{ \
return ((btf_##name)____##name)(__BPF_MAP(x,__BPF_CAST,__BPF_N,__VA_ARGS__));\
} \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__))
The notrace attribute is actually applied to the static always_inline function
____bpf_spin_{lock,unlock}(). The actual callback function
bpf_spin_{lock,unlock}() is not marked with notrace, hence
allowing fentry prog to attach to two helpers, and this
may cause the above mentioned deadlock. Siddharth Chintamaneni
actually has a reproducer in [2].
To fix the issue, a new macro NOTRACE_BPF_CALL_1 is introduced which
will add notrace attribute to the original function instead of
the hidden always_inline function and this fixed the problem.
This fixes:
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dtb: /: memory@40000000: 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/memory.yaml#
arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dtb: /: memory@40000000: 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/memory.yaml#
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240122132357.31264-1-zajec5@gmail.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cbas node is used to describe base detection functionality in the
ChromeOS EC, which is used for units that have a detachable keyboard and
thus rely on this functionality to switch between tablet and laptop
mode.
Despite the original commit having added the cbas node to the
mt8183-kukui.dtsi, not all machines that include it are detachables. In
fact all machines that include from mt8183-kukui-jacuzzi.dtsi are either
clamshells (ie normal laptops) or convertibles, meaning the keyboard can
be flipped but not detached. The detection for the keyboard getting
flipped is handled by the driver bound to the keyboard-controller node
in the EC.
Move the base detection node from the base kukui dtsi to the dtsis where
all machines are detachables, and thus actually make use of the node.
Fixes: 4fa8492d1e5b ("arm64: dts: mt8183: add cbas node under cros_ec") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240116-mt8183-kukui-cbas-remove-v3-1-055e21406e86@collabora.com Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a node describing the USB Type C connector, in order to utilize the
Chromium OS USB Type-C driver that enumerates Type-C ports and connected
cables/peripherals and makes them visible to userspace.
Cc: Alexandru M Stan <amstan@chromium.org> Cc: Benson Leung <bleung@chromium.org> Signed-off-by: Prashant Malani <pmalani@chromium.org> Reviewed-by: Alexandru M Stan <amstan@chromium.org> Reviewed-by: Benson Leung <bleung@chromium.org> Link: https://lore.kernel.org/r/20211209195112.366176-1-pmalani@chromium.org Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Stable-dep-of: 04bd6411f506 ("arm64: dts: mt8183: Move CrosEC base detection node to kukui-based DTs") Signed-off-by: Sasha Levin <sashal@kernel.org>
As discussed in the past (commit 2d3916f31891 ("ipv6: fix skb drops
in igmp6_event_query() and igmp6_event_report()")) I think the
synchronize_net() call in ipv6_mc_down() is not needed.
Under load, synchronize_net() can last between 200 usec and 5 ms.
KASAN seems to agree as well.
Fixes: f185de28d9ae ("mld: add new workqueues for process mld events") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Taehee Yoo <ap420073@gmail.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'-fPIC' as an option to the linker does not do what it seems like it
should. With ld.bfd, it is treated as '-f PIC', which does not make
sense based on the meaning of '-f':
-f SHLIB, --auxiliary SHLIB Auxiliary filter for shared object symbol table
When building with ld.lld (currently under review in a GitHub pull
request), it just errors out because '-f' means nothing and neither does
'-fPIC':
ld.lld: error: unknown argument '-fPIC'
'-fPIC' was blindly copied from CFLAGS when the vDSO stopped being
linked with '$(CC)', it should not be needed. Remove it to clear up the
build failure with ld.lld.
The firmware (later) actually uses the values even for keys
that are invalid as far as the host is concerned, later in
rekeying, and then only sets the low 48 bits since the PNs
are only 48 bits over the air. It does, however, compare the
full 64 bits later, obviously causing problems.
Remove the memset and use kzalloc instead to avoid any old
heap data leaking to the firmware. We already init all the
other fields in the struct anyway. This leaves the data set
to zero for any unused fields, so the firmware can look at
them safely even if they're not used right now.
Fixes: 79e561f0f05a ("iwlwifi: mvm: d3: implement RSC command version 5") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20240206175739.462101146fef.I10f3855b99417af4247cff04af78dcbc6cb75c9c@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver only used the number of pwm channels to set the pwm_chip's
npwm member. The result is that if there are more capture channels than
PWM channels specified in the device tree, only a part of the capture
channel is usable. Fix that by passing the bigger channel count to the
pwm framework. This makes it possible that the .apply() callback is
called with .hwpwm >= pwm_num_devs, catch that case and return an error
code.
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This just pushed a variant of pwm_apply_legacy() into the driver that was
slightly simplified because the driver doesn't provide a .set_polarity()
callback.
In the for statement of lbs_allocate_cmd_buffer(), if the allocation of
cmdarray[i].cmdbuf fails, both cmdarray and cmdarray[i].cmdbuf needs to
be freed. Otherwise, there will be memleaks in lbs_allocate_cmd_buffer().
Fixes: 876c9d3aeb98 ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240126075336.2825608-1-alexious@zju.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
The suspend callback disables the periph clock when the PWM is enabled
and resume reenables this clock if the PWM was disabled before. Judging
from the code comment it's suspend that is wrong here. Fix accordingly.
In PWM drivers the variable name "chip" is usually only used for struct
pwm_chip pointers. This driver however used "chip" for its driver data
and pwm_chip pointers are named "chip", too, when there is no driver
data around and "c" otherwise. Instead use "atmel" for driver data and
always "chip" for pwm_chips.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
The GW71xx does not have a gpio controlled vbus regulator but it does
require some pinctrl. Remove the regulator and move the valid pinctrl
into the usbotg1 node.
EWRD ACPI table contains up to 3 additional sar profiles.
According to the BIOS spec, the table contains a n_profile
variable indicating how many additional profiles exist in the
table.
Currently we check that n_profiles is not <= 0.
But according to the BIOS spec, 0 is a valid value,
and it can't be < 0 anyway because we receive that from ACPI as
an unsigned integer.
Fixes: 39c1a9728f93 ("iwlwifi: refactor the SAR tables from mvm to acpi") Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://msgid.link/20240129211905.448ea2f40814.Iffd2aadf8e8693e6cb599bee0406a800a0c1e081@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrei reports that we just silently drop beacons after we
report the key counters, but never report to userspace, so
wpa_supplicant cannot send the WNM action frame. Fix that.
Fixes: b1fdc2505abc ("iwlwifi: mvm: advertise BIGTK client support if available") Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20240128084842.7d855442cdce.Iba90b26f893dc8c49bfb8be65373cd0a138af12c@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ath9k_wmi_event_tasklet() used in ath9k_htc assumes that all the data
structures have been fully initialised by the time it runs. However, because of
the order in which things are initialised, this is not guaranteed to be the
case, because the device is exposed to the USB subsystem before the ath9k driver
initialisation is completed.
We already committed a partial fix for this in commit: 8b3046abc99e ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
However, that commit only aborted the WMI_TXSTATUS_EVENTID command in the event
tasklet, pairing it with an "initialisation complete" bit in the TX struct. It
seems syzbot managed to trigger the race for one of the other commands as well,
so let's just move the existing synchronisation bit to cover the whole
tasklet (setting it at the end of ath9k_htc_probe_device() instead of inside
ath9k_tx_init()).
Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
In order to use ultra high speed modes (UHS) on the SD card slot, we
add matching pinctrls and fix the voltage switching for LDO5 of the
PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.
These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_regulator_get_optional() returns -ENODEV if no supply can be found.
By introducing its usage, commit 788715b5f21c ("cpufreq: mediatek-hw:
Wait for CPU supplies before probing") caused the driver to fail probe
if no supply was present in any of the CPU DT nodes.
Use devm_regulator_get() instead since the CPUs do require supplies
even if not described in the DT. It will gracefully return a dummy
regulator if none is found in the DT node, allowing probe to succeed.
Fixes: 788715b5f21c ("cpufreq: mediatek-hw: Wait for CPU supplies before probing") Reported-by: kernelci.org bot <bot@kernelci.org> Closes: https://linux.kernelci.org/test/case/id/65b0b169710edea22852a3fa/ Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There exists the following warning when building bpftool:
CC prog.o
prog.c: In function ‘profile_open_perf_events’:
prog.c:2301:24: warning: ‘calloc’ sizes specified with ‘sizeof’ in the earlier argument and not in the later argument [-Wcalloc-transposed-args]
2301 | sizeof(int), obj->rodata->num_cpu * obj->rodata->num_metric);
| ^~~
prog.c:2301:24: note: earlier argument should specify number of elements, later size of each element
Tested with the latest upstream GCC which contains a new warning option
-Wcalloc-transposed-args. The first argument to calloc is documented to
be number of elements in array, while the second argument is size of each
element, just switch the first and second arguments of calloc() to silence
the build warning, compile tested only.
Before proceeding with the probe and enabling frequency scaling for the
CPUs, make sure that all supplies feeding the CPUs have probed.
This fixes an issue observed on MT8195-Tomato where if the
mediatek-cpufreq-hw driver enabled the hardware (by writing to
REG_FREQ_ENABLE) before the SPMI controller driver (spmi-mtk-pmif),
behind which lies the big CPU supply, probed the platform would hang
shortly after with "rcu: INFO: rcu_preempt detected stalls on
CPUs/tasks" being printed in the log.
Fixes: 4855e26bcf4d ("cpufreq: mediatek-hw: Add support for CPUFREQ HW") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Stable-dep-of: 788715b5f21c ("cpufreq: mediatek-hw: Wait for CPU supplies before probing") Signed-off-by: Sasha Levin <sashal@kernel.org>
debugfs_create_dir() returns ERR_PTR and never return NULL.
As Russell suggested, this patch removes the error checking for
debugfs_create_dir(). This is because the DebugFS kernel API is developed
in a way that the caller can safely ignore the errors that occur during
the creation of DebugFS nodes. The debugfs APIs have a IS_ERR() judge in
start_creating() which can handle it gracefully. So these checks are
unnecessary.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20230903030216.1509013-3-ruanjinjie@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
