When the last subscriber to a "Through" port has been removed, the
subscribed destination ports might still be active, so it would be
wrong to send "all sounds off" and "reset controller" events to them.
The proper place for such a shutdown would be the closing of the actual
MIDI port (and close_substream() in rawmidi.c already can do this).
This also fixes a deadlock when dummy_unuse() tries to send events to
its own port that is already locked because it is being freed.
Reported-by: Peter Billam <peter@www.pjb.com.au> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It seems in the past we have BDW with PCH not been propperly identified
and we force it to be LPT and we were warning !IS_HASWELL on propper identification.
Now that products are out there we are receiveing logs with this incorrect WARN.
And also according to local tests on all production BDW here ULT or HALO we don't
need this force anymore. So let's clean this block for real.
v2: Fix LPT_LP WARNs to avoid wrong warns on BDW_ULT (By Jani).
When creating a fence for a tiled object, only fence the area that
makes up the actual tiles. The object may be larger than the tiled
area and if we allow those extra addresses to be fenced, they'll
get converted to addresses beyond where the object is mapped. This
opens up the possiblity of writes beyond the end of object.
To prevent this, we adjust the size of the fence to only encompass
the area that makes up the actual tiles. The extra space is considered
un-tiled and now behaves as if it was a linear object.
Testcase: igt/gem_tiled_fence_overflow Reported-by: Dan Hettena <danh@ghs.com> Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
OTG device shall support this device for allowing compliance automated testing.
The modification is derived from Pavankumar and Vijayavardhans' previous work.
Signed-off-by: Macpaul Lin <macpaul@gmail.com> Cc: Pavankumar Kondeti <pkondeti@codeaurora.org> Cc: Vijayavardhan Vennapusa <vvreddy@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch adds a usb quirk to support devices with interupt endpoints
and bInterval values expressed as microframes. The quirk causes the
parse endpoint function to modify the reported bInterval to a standards
conforming value.
There is currently code in the endpoint parser that checks for
bIntervals that are outside of the valid range (1-16 for USB 2+ high
speed and super speed interupt endpoints). In this case, the code assumes
the bInterval is being reported in 1ms frames. As well, the correction
is only applied if the original bInterval value is out of the 1-16 range.
With this quirk applied to the device, the bInterval will be
accurately adjusted from microframes to an exponent.
Signed-off-by: James P Michels III <james.p.michels@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: 3.16-stable prereq for: e5dff0e80463 "USB: Add OTG PET device to TPL" ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Like some other uas devices these devices hang when a report-opcodes scsi
command is send to them.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1124119 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch solves deadlock between clock prepare mutex and regmap mutex reported
by Tomasz Figa in [1] by implementing solution from [2]: "always leave the clock
of the i2c controller in a prepared state".
On each i2c transfer handled by s3c24xx_i2c_xfer(), clk_prepare_enable() was
called, which calls clk_prepare() then clk_enable(). clk_prepare() takes
prepare_lock mutex before proceeding. Note that i2c transfer functions are
invoked from many places in kernel, typically with some other additional lock
held.
It may happen that function on CPU1 (e.g. regmap_update_bits()) has taken a
mutex (i.e. regmap lock mutex) then it attempts i2c communication in order to
proceed (so it needs to obtain clock related prepare_lock mutex during transfer
preparation stage due to clk_prepare() call). At the same time other task on
CPU0 wants to operate on clock (e.g. to (un)prepare clock for some other reason)
so it has taken prepare_lock mutex.
Implemented solution from [2] leaves i2c clock prepared. Preparation is done in
s3c24xx_i2c_probe() function. Without this patch, it is immediately unprepared
by clk_disable_unprepare() call. I've replaced this call with clk_disable() and
I've added clk_unprepare() call in s3c24xx_i2c_remove().
The s3c24xx_i2c_xfer() function now uses clk_enable() instead of
clk_prepare_enable() (and clk_disable() instead of clk_unprepare_disable()).
Signed-off-by: Paul Osmialowski <p.osmialowsk@samsung.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In case userspace attempts to obtain key information for or delete a
unicast key, this is currently erroneously rejected unless the driver
sets the WIPHY_FLAG_IBSS_RSN flag. Apparently enough drivers do so it
was never noticed.
Fix that, and while at it fix a potential memory leak: the error path
in the get_key() function was placed after allocating a message but
didn't free it - move it to a better place. Luckily admin permissions
are needed to call this operation.
Fixes: e31b82136d1ad ("cfg80211/mac80211: allow per-station GTKs") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fix a regression introduced by commit a5e70697d0c4 ("mac80211: add radiotap flag
and handling for 5/10 MHz") where the IEEE80211_CHAN_CCK channel type flag was
incorrectly replaced by the IEEE80211_CHAN_OFDM flag. This commit fixes that by
using the CCK flag again.
Fixes: a5e70697d0c4 ("mac80211: add radiotap flag and handling for 5/10 MHz") Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In normal cases (i.e. when we are fully associated), cfg80211 takes
care of removing all the stations before calling suspend in mac80211.
But in the corner case when we suspend during authentication or
association, mac80211 needs to roll back the station states. But we
shouldn't roll back the station states in the suspend function,
because this is taken care of in other parts of the code, except for
WDS interfaces. For AP types of interfaces, cfg80211 takes care of
disconnecting all stations before calling the driver's suspend code.
For station interfaces, this is done in the quiesce code.
For WDS interfaces we still need to do it here, so move the code into
a new switch case for WDS.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We only support swap file calling nfs_direct_IO. However, application
might be able to get to nfs_direct_IO if it toggles O_DIRECT flag
during IO and it can deadlock because we grab inode->i_mutex in
nfs_file_direct_write(). So return 0 for such case. Then the generic
layer will fall back to buffer IO.
Signed-off-by: Peng Tao <tao.peng@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit 3b8a3c010969 ("powerpc/pseries: Fix endiannes issue in RTAS
call from xmon") was fixing an endianness issue in the call made from
xmon to RTAS.
However, as Michael Ellerman noticed, this fix was not complete, the
token value was not byte swapped. This lead to call an unexpected and
most of the time unexisting RTAS function, which is silently ignored by
RTAS.
This fix addresses this hole.
Reported-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We should select FSR also to be driven by McBSP, not only FSX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
being NULL, hence when trying to set rtd a few lines below we get an oops.
Fix by using rtd->dai_link->dpcm_playback and rtd->dai_link->dpcm_capture as
playback_count and capture_count to snd_pcm_new_internal().
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If asoc_simple_card_probe() fails, asoc_simple_card_unref() may be
called before dev_set_drvdata(), causing a NULL pointer dereference in
asoc_simple_card_unref():
Unable to handle kernel NULL pointer dereference at virtual address 000000d4
...
PC is at asoc_simple_card_unref+0x14/0x48
LR is at asoc_simple_card_probe+0x3d4/0x40c
This typically happens because asoc_simple_card_parse_of() returns
-EPROBE_DEFER, but other failure modes are possible.
devm_snd_soc_register_card()/snd_soc_register_card() may fail either
before or after dev_set_drvdata().
Pass a snd_soc_card pointer instead of a platform_device pointer to
asoc_simple_card_unref() to fix this.
Note that if CONFIG_OF_DYNAMIC=n, of_node_put() is a dummy, and gcc may
optimize away the loop over card->dai_link, never actually dereferencing
card, and thus avoiding the crash...
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Fixes: e512e001dafa54e5 ("ASoC: simple-card: Fix the reference count of device nodes") Signed-off-by: Mark Brown <broonie@kernel.org>
[ luis: backported to 3.16:
- adjusted context
- dropped changes to asoc_simple_card_remove() ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The regulator framework maintains a list of consumer regulators
for a regulator device and protects it from concurrent access using
the regulator device's mutex lock.
In the case of regulator_put() the consumer is removed and regulator
device's parameters are updated without holding the regulator device's
mutex. This would lead to a race condition between the regulator_put()
and any function which traverses the consumer list or modifies regulator
device's parameters.
Fix this race condition by holding the regulator device's mutex in case
of regulator_put.
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The FIFO size is 40 accordingly to the specifications, but this means 0x40,
i.e. 64 bytes. This patch fixes the typo and enables FIFO size autodetection
for Intel MID devices.
Fixes: 7063c0d942a1 (spi/dw_spi: add DMA support) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
to test fifo == 257. In the case fifo is 257, it means the latest valid
setting is fifo = 256. So after the for loop iteration, we should check
fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Once the current message is finished, the driver notifies SPI core about
this by calling spi_finalize_current_message(). This function queues next
message to be transferred. If there are more messages in the queue, it is
possible that the driver is asked to transfer the next message at this
point.
When spi_finalize_current_message() returns the driver clears the
drv_data->cur_chip pointer to NULL. The problem is that if the driver
already started the next message clearing drv_data->cur_chip will cause
NULL pointer dereference which crashes the kernel like:
Fix this by clearing drv_data->cur_chip before we call spi_finalize_current_message().
Reported-by: Martin Oldfield <m@mjoldfield.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If a touchpad reports the F11 data40 register then this indicates that the touchpad reports
additional ACM (Accidental Contact Mitigation) data after the F11 data in the HID attention
report. These additional bytes shift the position of the F30 button data causing the driver
to incorrectly report button state when this functionality is present. This patch accounts
for the additional data in the report.
There are additional queries which are optional and may not be present
depending on the configuration of the firmware. Knowing which queries are
present is needed to properly compute the address of Query 12 and all
subsequent queries. Additional bits in Query 1 are used to indicate the
presence of these optional queries.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 2457aec63745 ("mm: non-atomically mark page accessed during page
cache allocation where possible") has added a separate parameter for
specifying gfp mask for radix tree allocations.
Not only this is less than optimal from the API point of view because it
is error prone, it is also buggy currently because
grab_cache_page_write_begin is using GFP_KERNEL for radix tree and if
fgp_flags doesn't contain FGP_NOFS (mostly controlled by fs by
AOP_FLAG_NOFS flag) but the mapping_gfp_mask has __GFP_FS cleared then
the radix tree allocation wouldn't obey the restriction and might
recurse into filesystem and cause deadlocks. This is the case for most
filesystems unfortunately because only ext4 and gfs2 are using
AOP_FLAG_NOFS.
Let's simply remove radix_gfp_mask parameter because the allocation
context is same for both page cache and for the radix tree. Just make
sure that the radix tree gets only the sane subset of the mask (e.g. do
not pass __GFP_WRITE).
Long term it is more preferable to convert remaining users of
AOP_FLAG_NOFS to use mapping_gfp_mask instead and simplify this
interface even further.
Reported-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
scripts/Makefile.clean treats absolute path specially, but
$(objtree)/debian is no longer an absolute path since 7e1c0477 (kbuild:
Use relative path for $(objtree). Work around this by checking if the
path starts with $(objtree)/.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com> Fixes: 7e1c0477 (kbuild: Use relative path for $(objtree) Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit a074335a370e ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev 0000000000000000 D sys_call_table 0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev 0000000000000000 R sys_call_table 0000000000000000 D syscall_table_size
Fixes: a074335a370e ("x86, um: Mark system call tables readonly") Cc: H. Peter Anvin <hpa@zytor.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
futex_atomic_cmpxchg_inatomic() does not work on UML because
it triggers a copy_from_user() in kernel context.
On UML copy_from_user() can only be used if the kernel was called
by a real user space process such that UML can use ptrace()
to fetch the value.
Reported-by: Miklos Szeredi <miklos@szeredi.hu> Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Richard Weinberger <richard@nod.at> Tested-by: Daniel Walter <d.walter@0x90.at> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
"origPtr" is used as an offset into the bd->dbuf[] array. That array is
allocated in start_bunzip() and has "bd->dbufSize" number of elements so
the test here should be >= instead of >.
Later we check "origPtr" again before using it as an offset so I don't
know if this bug can be triggered in real life.
Fixes: bc22c17e12c1 ('bzip2/lzma: library support for gzip, bzip2 and lzma decompression') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Alain Knaff <alain@knaff.lu> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Correct returning IRQ_HANDLED unconditionally in the irq handler.
Return IRQ_NONE for some interrupt which we do not expect to be
handled in this handler. This prevents kernel stalling with back
to back spurious interrupts.
On certain SoCs such as AM437x SoC, L3_noc error registers are
maintained in power domain such as per domain which looses context as part
of low power state such as RTC+DDR mode. On these platforms when we
mask interrupts which we cannot handle, the source of these interrupts
still remain on resume, however, the flag mux registers now contain
their reset value (unmasked) - this breaks the system with infinite
interrupts since we do not these interrupts to take place ever again.
To handle this: restore the masking of interrupts which we have
already recorded in the system as ones we cannot handle.
Fixes: 2100b595b7 ("bus: omap_l3_noc: ignore masked out unclearable targets") Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit f95499c3030f ("n_tty: Don't wait for buffer work in read() loop")
introduces a race window where a pty master can be signalled that the pty
slave was closed before all the data that the slave wrote is delivered.
Commit f8747d4a466a ("tty: Fix pty master read() after slave closes") fixed the
problem in case of n_tty_read, but the problem still exists for n_tty_poll.
This can be seen by running 'for ((i=0; i<100;i++));do ./test.py ;done'
where test.py is:
import os, select, pty
(pid, pty_fd) = pty.fork()
if pid == 0:
os.write(1, 'This string should be received by parent')
else:
poller = select.epoll()
poller.register( pty_fd, select.EPOLLIN )
ready = poller.poll( 1 * 1000 )
for fd, events in ready:
if not events & select.EPOLLIN:
print 'missed POLLIN event'
else:
print os.read(fd, 100)
poller.close()
The string from the slave is missed several times.
This patch takes the same approach as the fix for read and special cases
this condition for poll.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The 'max' size passed into the function is measured in number of bits
(KEY_MAX, LED_MAX, etc) so we need to convert it accordingly before trying
to copy the data out, otherwise we will try copying too much and end up
with up with a page fault.
Reported-by: Pavel Machek <pavel@ucw.cz> Reviewed-by: Pavel Machek <pavel@ucw.cz> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 5d26a105b5a7 ("crypto: prefix module autoloading with "crypto-"")
changed the automatic module loading when requesting crypto algorithms
to prefix all module requests with "crypto-". This requires all crypto
modules to have a crypto specific module alias even if their file name
would otherwise match the requested crypto algorithm.
Even though commit 5d26a105b5a7 added those aliases for a vast amount of
modules, it was missing a few. Add the required MODULE_ALIAS_CRYPTO
annotations to those files to make them get loaded automatically, again.
This fixes, e.g., requesting 'ecb(blowfish-generic)', which used to work
with kernels v3.18 and below.
Also change MODULE_ALIAS() lines to MODULE_ALIAS_CRYPTO(). The former
won't work for crypto modules any more.
Fixes: 5d26a105b5a7 ("crypto: prefix module autoloading with "crypto-"") Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[ luis: backported to 3.16: dropped changes to:
- arch/x86/crypto/sha-mb/sha1_mb.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This prefixes all crypto module loading with "crypto-" so we never run
the risk of exposing module auto-loading to userspace via a crypto API,
as demonstrated by Mathias Krause:
https://lkml.org/lkml/2013/3/4/70
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[ luis: backported to 3.16: dropped changes to:
- arch/arm/crypto/sha1_neon_glue.c
- arch/arm/crypto/sha512_neon_glue.c
- arch/x86/crypto/des3_ede_glue.c
- drivers/crypto/qat/qat_common/adf_ctl_drv.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Introduce a new variable to count the number of allocated migration
structures. The existing variable cache->nr_migrations became
overloaded. It was used to:
i) track of the number of migrations in flight for the purposes of
quiescing during suspend.
ii) to estimate the amount of background IO occuring.
Recent discard changes meant that REQ_DISCARD bios are processed with
a migration. Discards are not background IO so nr_migrations was not
incremented. However this could cause quiescing to complete early.
(i) is now handled with a new variable cache->nr_allocated_migrations.
cache->nr_migrations has been renamed cache->nr_io_migrations.
cleanup_migration() is now called free_io_migration(), since it
decrements that variable.
Also, remove the unused cache->next_migration variable that got replaced
with with prealloc_structs a while ago.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If a DM table is reloaded with an inactive table when the device is not
suspended (normal procedure for LVM2), then there will be two dm-bufio
objects that can diverge. This can lead to a situation where the
inactive table uses bufio to read metadata at the same time the active
table writes metadata -- resulting in the inactive table having stale
metadata buffers once it is promoted to the active table slot.
Fix this by using reference counting and a global list of cache metadata
objects to ensure there is only one metadata object per metadata device.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
SYSENTER emulation is broken in several ways:
1. It misses the case of 16-bit code segments completely (CVE-2015-0239).
2. MSR_IA32_SYSENTER_CS is checked in 64-bit mode incorrectly (bits 0 and 1 can
still be set without causing #GP).
3. MSR_IA32_SYSENTER_EIP and MSR_IA32_SYSENTER_ESP are not masked in
legacy-mode.
4. There is some unneeded code.
Fix it.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Many users see this message when booting without knowning that it is
of no importance and that TSC calibration may have succeeded by
another way.
As explained by Paul Bolle in
http://lkml.kernel.org/r/1348488259.1436.22.camel@x61.thuisdomein
"Fast TSC calibration failed" should not be considered as an error
since other calibration methods are being tried afterward. At most,
those send a warning if they fail (not an error). So let's change
the message from error to warning.
[ tglx: Make if pr_info. It's really not important at all ]
Fixes: c767a54ba065 x86/debug: Add KERN_<LEVEL> to bare printks, convert printks to pr_<level> Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com> Link: http://lkml.kernel.org/r/1418106470-6906-1-git-send-email-alexandre.f.demers@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 0dbc6078c06bc0 ('x86, build, pci: Fix PCI_MSI build on !SMP')
introduced the dependency that X86_UP_APIC is only available when
PCI_MSI is false. This effectively prevents PCI_MSI support on 32bit
UP systems because it disables both APIC and IO-APIC. But APIC support
is architecturally required for PCI_MSI.
The intention of the patch was to enforce APIC support when PCI_MSI is
enabled, but failed to do so.
Remove the !PCI_MSI dependency from X86_UP_APIC and enforce
X86_UP_APIC when PCI_MSI support is enabled on 32bit UP systems.
[ tglx: Massaged changelog ]
Fixes 0dbc6078c06bc0 'x86, build, pci: Fix PCI_MSI build on !SMP' Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Link: http://lkml.kernel.org/r/1421967529-9037-1-git-send-email-pure.logic@nexus-software.ie Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Strictly speaking, this code was never correct. It should have set
read_exec_only and seg_not_present to 1 to indicate that it wanted
to find a free slot without putting anything there, or it should
have put something sensible in the TLS slot if it wanted to allocate
a TLS entry for real. The actual effect of this code was to
allocate a bogus segment that could be used to exploit espfix.
The set_thread_area hardening patches changed the behavior, causing
set_thread_area to return -EINVAL and crashing the game.
This changes set_thread_area to interpret this as a request to find
a free slot and to leave it empty, which isn't *quite* what the game
expects but should be close enough to keep it working. In
particular, using the code above to allocate two segments will
allocate the same segment both times.
According to FrostbittenKing on Github, this fixes The Witcher 2.
If this somehow still causes problems, we could instead allocate
a limit==0 32-bit data segment, but that seems rather ugly to me.
32-bit programs don't have an lm bit in their ABI, so they can't
reliably cause LDT_empty to return true without resorting to memset.
They shouldn't need to do this.
This should fix a longstanding, if minor, issue in all 64-bit kernels
as well as a potential regression in the TLS hardening code.
The locking scheme inside the vb2 thread is unsafe when stopping the
thread. In particular kthread_stop was called *after* internal data
structures were cleaned up instead of doing that before. In addition,
internal vb2 functions were called after threadio->stop was set to
true and vb2_internal_streamoff was called. This is also not allowed.
All this led to a variety of race conditions and kernel warnings and/or
oopses.
Fixed by moving the kthread_stop call up before the cleanup takes
place, and by checking threadio->stop before calling internal vb2
queuing operations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
sd_set_power_mode() in derived module drivers/mmc/host/rtsx_usb_sdmmc.c
acquires dev_mutex and then calls pm_runtime_get_sync() to make sure the
device is awake while initializing a newly inserted card. Once it is
called during suspending state and explicitly before rtsx_usb_suspend()
acquires the same dev_mutex, both routine deadlock and further hang the
driver because pm_runtime_get_sync() waits the pending PM operations.
Fix this by using an empty suspend method. mmc_core always turns the
LED off after a request is done and thus it is ok to remove the only
rtsx_usb_turn_off_led() here.
Fixes: 730876be2566 ("mfd: Add realtek USB card reader driver") Signed-off-by: Roger Tseng <rogerable@realtek.com>
[Lee: Removed newly unused variable] Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If we don't tell regmap-irq that our first status
register is at offset 1, it will try to read offset
zero, which is the chipid register.
Fixes: 44b4dc6 mfd: tps65218: Add driver for the TPS65218 PMIC Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
STATUS register can be modified by the HW, so we
should bypass cache because of that.
In the case of INT[12] registers, they are the ones
that actually clear the IRQ source at the time they
are read. If we rely on the cache for them, we will
never be able to clear the interrupt, which will cause
our IRQ line to be disabled due to IRQ throttling.
Fixes: 44b4dc6 mfd: tps65218: Add driver for the TPS65218 PMIC Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On 64-bit, relocation is not required unless the load address gets
changed. Without this, relocations do unexpected things when the kernel
is above 4G.
Reported-by: Baoquan He <bhe@redhat.com> Signed-off-by: Kees Cook <keescook@chromium.org> Tested-by: Thomas D. <whissi@whissi.de> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Jan Beulich <JBeulich@suse.com> Cc: Junjie Mao <eternal.n08@gmail.com> Cc: Andi Kleen <ak@linux.intel.com> Link: http://lkml.kernel.org/r/20150116005146.GA4212@www.outflux.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On Armada XP, 375 and 38x the MBus window 13 has the remap capability,
like windows 0 to 7. However, the mvebu-mbus driver isn't currently
taking into account this special case, which means that when window 13
is actually used, the remap registers are left to 0, making the device
using this MBus window unavailable.
As a minimal fix for stable, don't use window 13. A full fix will
follow later.
Fixes: fddddb52a6c ("bus: introduce an Marvell EBU MBus driver") Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It is possible for ata_sff_flush_pio_task() to set ap->hsm_task_state to
HSM_ST_IDLE in between the time __ata_sff_port_intr() checks for HSM_ST_IDLE
and before it calls ata_sff_hsm_move() causing ata_sff_hsm_move() to BUG().
This problem is hard to reproduce making this patch hard to verify, but this
fix will prevent the race.
I have not been able to reproduce the problem, but here is a crash dump from
a 2.6.32 kernel.
On examining the ata port's state, its hsm_task_state field has a value of HSM_ST_IDLE:
Normally, this should not be possible as ata_sff_hsm_move() was called from ata_sff_host_intr(),
which checks hsm_task_state and won't call ata_sff_hsm_move() if it has a HSM_ST_IDLE value.
Somewhere between the ata_sff_hsm_move() check and the ata_sff_host_intr() check, the value changed.
On examining the other cpus to see what else was running, another cpu was running the error handler
routines:
Before it tried to acquire a spinlock, ata_exec_internal_sg() called ata_sff_flush_pio_task().
This function will set ap->hsm_task_state to HSM_ST_IDLE, and has no locking around setting this
value. ata_sff_flush_pio_task() can then race with the interrupt handler and potentially set
HSM_ST_IDLE at a fatal moment, which will trigger a kernel BUG.
v2: Fixup comment in ata_sff_flush_pio_task()
tj: Further updated comment. Use ap->lock instead of shost lock and
use the [un]lock_irq variant instead of the irqsave/restore one.
Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Compiling SH with gcc-4.8 fails due to the -m32 option not being
supported.
From http://buildd.debian-ports.org/status/fetch.php?pkg=linux&arch=sh4&ver=3.16.7-ckt4-1&stamp=1421425783
CC init/main.o
gcc-4.8: error: unrecognized command line option '-m32'
ld: cannot find init/.tmp_mc_main.o: No such file or directory
objcopy: 'init/.tmp_mx_main.o': No such file
rm: cannot remove 'init/.tmp_mx_main.o': No such file or directory
rm: cannot remove 'init/.tmp_mc_main.o': No such file or directory
Ronny reports: https://bugzilla.kernel.org/show_bug.cgi?id=87101
"Since commit 8a4aeec8d "libata/ahci: accommodate tag ordered
controllers" the access to the harddisk on the first SATA-port is
failing on its first access. The access to the harddisk on the
second port is working normal.
When reverting the above commit, access to both harddisks is working
fine again."
Maintain tag ordered submission as the default, but allow sata_sil24 to
continue with the old behavior.
Cc: Tejun Heo <tj@kernel.org> Reported-by: Ronny Hegewald <Ronny.Hegewald@online.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fixes a race condition in abort handling that was injected
when multiple interrupt support was added. When only a single
interrupt is present, the adapter guarantees it will send
responses for aborted commands prior to the response for the
abort command itself. With multiple interrupts, these responses
generally come back on different interrupts, so we need to
ensure the abort thread waits until the aborted command is
complete so we don't perform a double completion. This race
condition was being hit frequently in environments which
were triggering command timeouts, which was resulting in
a double completion causing a kernel oops.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com> Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It really needs to check that src is non-directory *and* use
{un,}lock_two_nodirectories(). As it is, it's trivial to cause
double-lock (ioctl(fd, CIFS_IOC_COPYCHUNK_FILE, fd)) and if the
last argument is an fd of directory, we are asking for trouble
by violating the locking order - all directories go before all
non-directories. If the last argument is an fd of parent
directory, it has 50% odds of locking child before parent,
which will cause AB-BA deadlock if we race with unlink().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Jason Lee Cragg <jcragg@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The current hardware I/O coherency is known to cause problems with DMA
coherent buffers, as it still requires explicit I/O synchronization
barriers, which is not compatible with the semantics expected by the
Linux DMA coherent buffers API.
So, in order to have enough time to validate a new solution based on
automatic I/O synchronization barriers, this commit disables hardware
I/O coherency entirely. Future patches will re-enable it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A worker_pool's forward progress is guaranteed by the fact that the
last idle worker assumes the manager role to create more workers and
summon the rescuers if creating workers doesn't succeed in timely
manner before proceeding to execute work items.
This manager role is implemented in manage_workers(), which indicates
whether the worker may proceed to work item execution with its return
value. This is necessary because multiple workers may contend for the
manager role, and, if there already is a manager, others should
proceed to work item execution.
Unfortunately, the function also indicates that the worker may proceed
to work item execution if need_to_create_worker() is false at the head
of the function. need_to_create_worker() tests the following
conditions.
pending work items && !nr_running && !nr_idle
The first and third conditions are protected by pool->lock and thus
won't change while holding pool->lock; however, nr_running can change
asynchronously as other workers block and resume and while it's likely
to be zero, as someone woke this worker up in the first place, some
other workers could have become runnable inbetween making it non-zero.
If this happens, manage_worker() could return false even with zero
nr_idle making the worker, the last idle one, proceed to execute work
items. If then all workers of the pool end up blocking on a resource
which can only be released by a work item which is pending on that
pool, the whole pool can deadlock as there's no one to create more
workers or summon the rescuers.
This patch fixes the problem by removing the early exit condition from
maybe_create_worker() and making manage_workers() return false iff
there's already another manager, which ensures that the last worker
doesn't start executing work items.
We can leave the early exit condition alone and just ignore the return
value but the only reason it was put there is because the
manage_workers() used to perform both creations and destructions of
workers and thus the function may be invoked while the pool is trying
to reduce the number of workers. Now that manage_workers() is called
only when more workers are needed, the only case this early exit
condition is triggered is rare race conditions rendering it pointless.
Tested with simulated workload and modified workqueue code which
trigger the pool deadlock reliably without this patch.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Eric Sandeen <sandeen@sandeen.net> Link: http://lkml.kernel.org/g/54B019F4.8030009@sandeen.net Cc: Dave Chinner <david@fromorbit.com> Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
[ luis: backported to 3.16:
- maybe_create_worker() is now void, 'return' instead of 'return true' ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog] Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491 Reported-by: Marek Kordik <kordikmarek@gmail.com> Tested-by: Marek Kordik <kordikmarek@gmail.com> Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: "H. Peter Anvin" <hpa@zytor.com> CC: x86@kernel.org Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add pci_claim_bridge_resource() to claim a PCI-PCI bridge window. This is
like regular pci_claim_resource(), except that if we fail to claim the
window, we check to see if we can reduce the size of the window and try
again.
The 00:01.0 window is illegal: it starts before the host bridge window, so
we have to assume the [0xbdf00000-0xbfffffff] region is inaccessible. We
can make it legal by clipping it to [mem 0xc0000000-0xddefffff 64bit pref].
Previously we discarded the 00:01.0 window and tried to reassign that part
of the hierarchy from scratch. That is a problem because Linux doesn't
always assign things optimally. For example, in this case, BIOS put the
01:00.0 device in a prefetchable window below 4GB, but after 5b28541552ef,
Linux puts the prefetchable window above 4GB where the 32-bit 01:00.0
device can't use it.
Clipping the 00:01.0 window is less intrusive than completely reassigning
things and is sufficient to let us use most of the BIOS configuration. Of
course, it's possible that devices below 00:01.0 will no longer fit. If
that's the case, we'll have to reassign things. But that's a separate
problem.
[bhelgaas: changelog, split into separate patch] Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491 Reported-by: Marek Kordik <kordikmarek@gmail.com> Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add pci_bus_clip_resource(). If a PCI-PCI bridge window overlaps an
upstream bridge window but is not completely contained by it, this clips
the downstream window so it fits inside the upstream one.
No functional change (this adds the function but no callers).
[bhelgaas: changelog, split into separate patch] Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491 Reported-by: Marek Kordik <kordikmarek@gmail.com> Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
pci_setup_bridge_io(), pci_setup_bridge_mmio(), and
pci_setup_bridge_mmio_pref() program the windows of PCI-PCI bridges.
Previously they accepted a pointer to the pci_bus of the secondary bus,
then looked up the bridge leading to that bus. Pass the bridge directly,
which will make it more convenient for future callers.
No functional change.
[bhelgaas: changelog, split into separate patch] Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491 Reported-by: Marek Kordik <kordikmarek@gmail.com> Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Reports against the TL-WDN4800 card indicate that PCI bus reset of this
Atheros device cause system lock-ups and resets. I've also been able to
confirm this behavior on multiple systems. The device never returns from
reset and attempts to access config space of the device after reset result
in hangs. Blacklist bus reset for the device to avoid this issue.
[bhelgaas: This regression appeared in v3.14. Andreas bisected it to 425c1b223dac ("PCI: Add Virtual Channel to save/restore support"), but we
don't understand the mechanism by which that commit affects the reset
path.]
[bhelgaas: changelog, references] Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org Reported-by: Andreas Hartmann <andihartmann@freenet.de> Tested-by: Andreas Hartmann <andihartmann@freenet.de> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Enable a mechanism for devices to quirk that they do not behave when
doing a PCI bus reset. We require a modest level of spec compliant
behavior in order to do a reset, for instance the device should come
out of reset without throwing errors and PCI config space should be
accessible after reset. This is too much to ask for some devices.
The gpio device attributes were never destroyed when the gpio was
unexported (or on export failures).
Use device_create_with_groups() to create the default device attributes
of the gpio class device. Note that this also fixes the
attribute-creation race with userspace for these attributes.
Remove contingent attributes in export error path and on unexport.
Fixes: d8f388d8dc8d ("gpio: sysfs interface") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16:
- file rename: drivers/gpio/gpiolib-sysfs.c -> drivers/gpio/gpiolib.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Recent Leaf firmware versions (>= 3.1.557) do not allow to send
commands for non-existing channels. If a command is sent for a
non-existing channel, the firmware crashes.
Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au> Signed-off-by: Olivier Sobrie <olivier@sobrie.be> Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in very high frequency (*), closing the CAN channel while
all the transmissions are on (#), opening the device again (@),
then sending a small number of packets would make the driver
enter an almost infinite loop of:
_dragging the whole system down_ in the process due to the
excessive logging output.
Initially, this has caused random panics in the kernel due to a
buggy error recovery path. That got fixed in an earlier commit.(%)
This patch aims at solving the root cause. -->
16 tx URBs and contexts are allocated per CAN channel per USB
device. Such URBs are protected by:
a) A simple atomic counter, up to a value of MAX_TX_URBS (16)
b) A flag in each URB context, stating if it's free
c) The fact that ndo_start_xmit calls are themselves protected
by the networking layers higher above
After grabbing one of the tx URBs, if the driver noticed that all
of them are now taken, it stops the netif transmission queue.
Such queue is worken up again only if an acknowedgment was received
from the firmware on one of our earlier-sent frames.
Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP
to the firmware, effectively closing all further communication. In
the high traffic case, the atomic counter remains at MAX_TX_URBS,
and all the URB contexts remain marked as active. While opening
the channel again (@), it cannot send any further frames since no
more free tx URB contexts are available.
Reset all tx URB contexts upon CAN channel close.
(*) 50 parallel instances of `cangen0 -g 0 -ix`
(#) `ifconfig can0 down`
(@) `ifconfig can0 up`
(%) "can: kvaser_usb: Don't free packets when tight on URBs"
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in high frequency caused seemingly-random panics in the
kernel.
On further inspection, it seems the driver erroneously freed the
to-be-transmitted packet upon getting tight on URBs and returning
NETDEV_TX_BUSY, leading to invalid memory writes and double frees
at a later point in time.
Note:
Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY
is a driver bug in and out of itself: it means that our start/stop
queue flow control is broken.
This patch only fixes the (buggy) error handling code; the root
cause shall be fixed in a later commit.
Acked-by: Olivier Sobrie <olivier@sobrie.be> Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When changing flags in the CAN drivers ctrlmode the provided new content has to
be checked whether the bits are allowed to be changed. The bits that are to be
changed are given as a bitfield in cm->mask. Therefore checking against
cm->flags is wrong as the content can hold any kind of values.
The iproute2 tool sets the bits in cm->mask and cm->flags depending on the
detected command line options. To be robust against bogus user space
applications additionally sanitize the provided flags with the provided mask.
Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fix memory leak and sleep-while-atomic in gpiochip_remove.
The memory leak was introduced by afa82fab5e13 ("gpio / ACPI: Move event
handling registration to gpiolib irqchip helpers") that moved the
release of acpi interrupt resources to gpiochip_irqchip_remove, but by
then the resources are no longer accessible as the acpi_gpio_chip has
already been freed by acpi_gpiochip_remove.
Note that this also fixes a few potential sleep-while-atomics, which has
been around since 1425052097b5 ("gpio: add IRQ chip helpers in gpiolib")
when the call to gpiochip_irqchip_remove while holding a spinlock was
added (a couple of irq-domain paths can end up grabbing mutexes).
Fixes: afa82fab5e13 ("gpio / ACPI: Move event handling registration to
gpiolib irqchip helpers") Fixes: 1425052097b5 ("gpio: add IRQ chip helpers in gpiolib") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Memory allocated and references taken by of_gpiochip_add and
acpi_gpiochip_add were never released on errors in gpiochip_add (e.g.
failure to find free gpio range).
Fixes: 391c970c0dd1 ("of/gpio: add default of_xlate function if device
has a node pointer") Fixes: 664e3e5ac64c ("gpio / ACPI: register to ACPI events
automatically")
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch is to fix two deadlock cases.
Deadlock 1:
CPU #1
pinctrl_register-> pinctrl_get ->
create_pinctrl
(Holding lock pinctrl_maps_mutex)
-> get_pinctrl_dev_from_devname
(Trying to acquire lock pinctrldev_list_mutex)
CPU #0
pinctrl_unregister
(Holding lock pinctrldev_list_mutex)
-> pinctrl_put ->> pinctrl_free ->
pinctrl_dt_free_maps -> pinctrl_unregister_map
(Trying to acquire lock pinctrl_maps_mutex)
Simply to say
CPU#1 is holding lock A and trying to acquire lock B,
CPU#0 is holding lock B and trying to acquire lock A.
Deadlock 2:
CPU #3
pinctrl_register-> pinctrl_get ->
create_pinctrl
(Holding lock pinctrl_maps_mutex)
-> get_pinctrl_dev_from_devname
(Trying to acquire lock pinctrldev_list_mutex)
CPU #2
pinctrl_unregister
(Holding lock pctldev->mutex)
-> pinctrl_put ->> pinctrl_free ->
pinctrl_dt_free_maps -> pinctrl_unregister_map
(Trying to acquire lock pinctrl_maps_mutex)
CPU #0
tegra_gpio_request
(Holding lock pinctrldev_list_mutex)
-> pinctrl_get_device_gpio_range
(Trying to acquire lock pctldev->mutex)
Simply to say
CPU#3 is holding lock A and trying to acquire lock D,
CPU#2 is holding lock B and trying to acquire lock A,
CPU#0 is holding lock D and trying to acquire lock B.
Signed-off-by: Jim Lin <jilin@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If CONFIG_DEBUG_MUTEXES is set, the mutex->owner field is only cleared
if the mutex debugging is enabled which introduces a race in our
mutex_is_locked_by() - i.e. we may inspect the old owner value before it
is acquired by the new task.
/*
* __mutex_slowpath_needs_to_unlock() is explicitly 0 for debug
* mutexes so that we can do it here after we've verified state.
*/
+ mutex_clear_owner(lock);
atomic_set(&lock->count, 1);
}
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87955 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Reported-and-tested-by: Scott Tsai <scottt.tw@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87759 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This change allows the driver to recognize newer Elantech touchpads.
Signed-off-by: Yi ju Hong <sam.hung@emc.com.tw> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We need to wait for the GPUVM flush to complete. There
was some confusion as to how this mechanism was supposed
to work. The operation is not atomic. For GPU initiated
invalidations you need to read back a VM register to
introduce enough latency for the update to complete.
v2: drop gart changes
v3: just read back rather than polling
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We need to wait for the GPUVM flush to complete. There
was some confusion as to how this mechanism was supposed
to work. The operation is not atomic. For GPU initiated
invalidations you need to read back a VM register to
introduce enough latency for the update to complete.
v2: drop gart changes
v3: just read back rather than polling
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ luis: backported to 3.16:
- replaced vm_id by vm->id
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We need to wait for the GPUVM flush to complete. There
was some confusion as to how this mechanism was supposed
to work. The operation is not atomic. For GPU initiated
invalidations you need to read back a VM register to
introduce enough latency for the update to complete.
v2: drop gart changes
v3: just read back rather than polling
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On some laptops, keyboard needs to be reset in order to successfully detect
touchpad (e.g., some Gigabyte laptop models with Elantech touchpads).
Without resettin keyboard touchpad pretends to be completely dead.
Based on the original patch by Mateusz Jończyk this version has been
expanded to include DMI based detection & application of the fix
automatically on the affected models of laptops. This has been confirmed to
fix problem by three users already on three different models of laptops.
An unvalidated user input is multiplied by a constant, which can result in
an undefined behaviour for large values. While this is validated later,
we should avoid triggering undefined behaviour.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[jstultz: include trivial milisecond->microsecond correction noticed
by Andy] Signed-off-by: John Stultz <john.stultz@linaro.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
EXYNOS4_MCT_L_MASK is defined as 0xffffff00, so applying this bitmask
produces a number outside the range 0x00 to 0xff, which always results
in execution of the default switch statement.
Obviously this is wrong and git history shows that the bitmask inversion
was incorrectly set during a refactoring of the MCT code.
Fix this by putting the inversion at the correct position again.
Acked-by: Kukjin Kim <kgene.kim@samsung.com> Reported-by: GP Orcullo <kinsamanka@gmail.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
