__hyp_call_panic_nvhe contains inline assembly which did not declare
its dependency on the __hyp_panic_string symbol.
The static-declared string has previously been kept alive because of a use in
__hyp_call_panic_vhe. Fix this in preparation for separating the source files
between VHE and nVHE when the two users land in two different compilation
units. The static variable otherwise gets dropped when compiling the nVHE
source file, causing an undefined symbol linker error later.
According to https://www.kernel.org/doc/Documentation/gpio/consumer.txt,
- all of the gpiod_set_value_xxx() functions operate with the *logical*
value. So in imx290_power_on() the reset signal should be cleared
(de-asserted) with gpiod_set_value_cansleep(imx290->rst_gpio, 0), and in
imx290_power_off() the value of 1 must be used to apply/assert the reset
to the sensor. In the device tree the reset pin is described as
GPIO_ACTIVE_LOW, and gpiod_set_value_xxx() functions take this into
account,
- when devm_gpiod_get_optional() is called with GPIOD_ASIS, the GPIO is
not initialized, and the direction must be set later; using a GPIO
without setting its direction first is illegal and will result in undefined
behavior. Fix this by using GPIOD_OUT_HIGH instead of GPIOD_ASIS (this
asserts the reset signal to the sensor initially).
In case of errors vpif_probe_complete() releases memory for vpif_obj.sd
and unregisters the V4L2 device. But then this is done again by
vpif_probe() itself. The patch removes the cleaning from
vpif_probe_complete().
Found by Linux Driver Verification project (linuxtesting.org).
syzbot found issues with having hugetlbfs on a union/overlay as reported
in [1]. Due to the limitations (no write) and special functionality of
hugetlbfs, it does not work well in filesystem stacking. There are no
know use cases for hugetlbfs stacking. Rather than making modifications
to get hugetlbfs working in such environments, simply prevent stacking.
The Intel uncore driver may claim some of the pci ids from ie31200 which
means that the ie31200 edac driver will not initialize them as part of
pci_register_driver().
Let's add a fallback for this case to 'pci_get_device()' to get a
reference on the device such that it can still be configured. This is
similar in approach to other edac drivers.
In aio case, if the completion comes very fast just before the
ceph_read_iter() returns to fs/aio.c, the kiocb will be freed in
the completion callback, then if ceph_read_iter() access again
we will potentially hit the use-after-free bug.
[ jlayton: initialize direct_lock early, and use it everywhere ]
URL: https://tracker.ceph.com/issues/45649 Signed-off-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure the delayed work stopped before releasing the resources.
cancel_delayed_work_sync() will only guarantee that the work finishes
executing if the work is already in the ->worklist. That means after
the cancel_delayed_work_sync() returns, it will leave the work requeued
if it was rearmed at the end. That can lead to a use after free once the
work struct is freed.
Fix it by flushing the delayed work instead of trying to cancel it, and
ensure that the work doesn't rearm if the mdsc is stopping.
URL: https://tracker.ceph.com/issues/46293 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
vfs_inode is used only for the inode number everything else requires
btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ use btrfs_ino ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The incoming qgroup reserved space timing will move the data reservation
to ordered extent completely.
However in btrfs_punch_hole_lock_range() will call
btrfs_invalidate_page(), which will clear QGROUP_RESERVED bit for the
range.
In current stage it's OK, but if we're making ordered extents handle the
reserved space, then btrfs_punch_hole_lock_range() can clear the
QGROUP_RESERVED bit before we submit ordered extent, leading to qgroup
reserved space leakage.
So here change the timing to make reserve data space after
btrfs_punch_hole_lock_range().
The new timing is fine for either current code or the new code.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Though the number of lock-acquisitions is tracked as unsigned long, this
is passed as the divisor to div_s64() which interprets it as a s32,
giving nonsense values with more than 2 billion acquisitons. E.g.
nouveau_connector_detect() calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
nv50_disp_atomic_commit() calls calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
nouveau_fbcon_open() calls calls pm_runtime_get_sync() that
increments the reference count. In case of failure, decrement the
ref count before returning the error.
During umount, f2fs_put_super() unregisters procfs entries after
f2fs_destroy_segment_manager(), it may cause use-after-free
issue when umount races with procfs accessing, fix it by relocating
f2fs_unregister_sysfs().
[Chao Yu: change commit title/message a bit]
Signed-off-by: Li Guifu <bluce.liguifu@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Logitech GROUP is a compound with camera and audio.
When the HID interface in an audio device is requested to get
specific report id, all following control transfers are stalled
and never be restored back.
The rt711 jack detection properties are set from the machine drivers
during the card probe, as done in other ASoC examples.
KASAN reports a use-after-free error when unbinding drivers due to a
confusing sequence between the ACPI core, the device core and the
SoundWire device cleanups.
Rather than fixing this sequence, follow the recommendation to have
the same caller add and remove properties, add an explicit
device_remove_properties() in the card .remove() callback.
In future patches the use of device_add/remove_properties will be
replaced by a direct handling of a swnode, but the sequence will
remain the same.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20200717211337.31956-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse.
To use the TMR_FIPER register to generate desired periodic
pulses. The value should programmed is,
desired_period - tclk_period
Current tmr-fiper2 value is to generate 100us periodic pulses.
(But the value should have been 99995, not 99990. The tclk_period is 5.)
This patch is to generate 1 second periodic pulses with value 999999995 programmed which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kobject_init_and_add() takes a reference even when it fails. If it returns
an error, kobject_put() must be called to clean up the memory associated
with the object.
When kobject_init_and_add() fails, call kobject_put() instead of kfree().
b8eb718348b8 ("net-sysfs: Fix reference count leak in
rx|netdev_queue_add_kobject") fixed a similar problem.
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
- don't panic kernel if f2fs_get_node_page() fails in
f2fs_recover_inline_data() or f2fs_recover_inline_xattr();
- return error number of f2fs_truncate_blocks() to
f2fs_recover_inline_data()'s caller;
An extra count on ebb_state.stats.pmc_count[PMC_INDEX(pmc)] is being per-
formed when count_pmc() is used to reset PMCs on a few selftests. This
extra pmc_count can occasionally invalidate results, such as the ones from
cycles_test shown hereafter. The ebb_check_count() failed with an above
the upper limit error due to the extra value on ebb_state.stats.pmc_count.
Furthermore, this extra count is also indicated by extra PMC1 trace_log on
the output of the cycle test (as well as on pmc56_overflow_test):
transport_init_session can allocate memory via percpu_ref_init, and
target_xcopy_release_pt never frees it. This adds a
transport_uninit_session function to handle cleanup of resources allocated
in the init function.
In tracking down a problem in this patchset, I discovered we are
reclaiming dirty stale inodes. This wasn't discovered until inodes
were always attached to the cluster buffer and then the rcu callback
that freed inodes was assert failing because the inode still had an
active pointer to the cluster buffer after it had been reclaimed.
Debugging the issue indicated that this was a pre-existing issue
resulting from the way the inodes are handled in xfs_inactive_ifree.
When we free a cluster buffer from xfs_ifree_cluster, all the inodes
in cache are marked XFS_ISTALE. Those that are clean have nothing
else done to them and so eventually get cleaned up by background
reclaim. i.e. it is assumed we'll never dirty/relog an inode marked
XFS_ISTALE.
On journal commit dirty stale inodes as are handled by both
buffer and inode log items to run though xfs_istale_done() and
removed from the AIL (buffer log item commit) or the log item will
simply unpin it because the buffer log item will clean it. What happens
to any specific inode is entirely dependent on which log item wins
the commit race, but the result is the same - stale inodes are
clean, not attached to the cluster buffer, and not in the AIL. Hence
inode reclaim can just free these inodes without further care.
However, if the stale inode is relogged, it gets dirtied again and
relogged into the CIL. Most of the time this isn't an issue, because
relogging simply changes the inode's location in the current
checkpoint. Problems arise, however, when the CIL checkpoints
between two transactions in the xfs_inactive_ifree() deferops
processing. This results in the XFS_ISTALE inode being redirtied
and inserted into the CIL without any of the other stale cluster
buffer infrastructure being in place.
Hence on journal commit, it simply gets unpinned, so it remains
dirty in memory. Everything in inode writeback avoids XFS_ISTALE
inodes so it can't be written back, and it is not tracked in the AIL
so there's not even a trigger to attempt to clean the inode. Hence
the inode just sits dirty in memory until inode reclaim comes along,
sees that it is XFS_ISTALE, and goes to reclaim it. This reclaiming
of a dirty inode caused use after free, list corruptions and other
nasty issues later in this patchset.
Hence this patch addresses a violation of the "never log XFS_ISTALE
inodes" caused by the deferops processing rolling a transaction
and relogging a stale inode in xfs_inactive_free. It also adds a
bunch of asserts to catch this problem in debug kernels so that
we don't reintroduce this problem in future.
Reproducer for this issue was generic/558 on a v4 filesystem.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
in amdgpu_display_crtc_set_config, the call to pm_runtime_get_sync
increments the counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
in amdgpu_drm_ioctl the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
in amdgpu_driver_open_kms the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Signed-off-by: Qiushi Wu <wu000273@umn.edu> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
EC is using 32 bit timestamps (us), and before converting it to 64bit
they were not casted, so it would overflow every 4s.
Regular overflow every ~70 minutes was not taken into account either.
Unlike the other instances which represent a complete loss of
consistency within the rcache mechanism itself, or a fundamental
and obvious misconfiguration by an IOMMU driver, the BUG_ON() in
iova_magazine_free_pfns() can be provoked at more or less any time
in a "spooky action-at-a-distance" manner by any old device driver
passing nonsense to dma_unmap_*() which then propagates through to
queue_iova().
Not only is this well outside the IOVA layer's control, it's also
nowhere near fatal enough to justify panicking anyway - all that
really achieves is to make debugging the offending driver more
difficult. Let's simply WARN and otherwise ignore bogus PFNs.
Intel Tiger Lake PCH-H has the same LPSS than Intel Broxton.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If tcmu_handle_completions() has to process a padding shorter than
sizeof(struct tcmu_cmd_entry), the current call to
tcmu_flush_dcache_range() with sizeof(struct tcmu_cmd_entry) as length
param is wrong and causes crashes on e.g. ARM, because
tcmu_flush_dcache_range() in this case calls
flush_dcache_page(vmalloc_to_page(start)); with start being an invalid
address above the end of the vmalloc'ed area.
The fix is to use the minimum of remaining ring space and sizeof(struct
tcmu_cmd_entry) as the length param.
The patch was tested on kernel 4.19.118.
See https://bugzilla.kernel.org/show_bug.cgi?id=208045#c10
Link: https://lore.kernel.org/r/20200629093756.8947-1-bstroesser@ts.fujitsu.com Tested-by: JiangYu <lnsyyj@hotmail.com> Acked-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We make an assumption that a debugfs directory exists, but since
this can fail ensure it exists before allowing blktrace setup to
complete. Otherwise we end up stuffing blktrace files on the debugfs
root directory. In the worst case scenario this *in theory* can create
an eventual panic *iff* in the future a similarly named file is created
prior on the debugfs root directory. This theoretical crash can happen
due to a recursive removal followed by a specific dentry removal.
This doesn't fix any known crash, however I have seen the files
go into the main debugfs root directory in cases where the debugfs
directory was not created due to other internal bugs with blktrace
now fixed.
blktrace is also completely useless without this directory, so
this ensures to userspace we only setup blktrace if the kernel
can stuff files where they are supposed to go into.
debugfs directory creations typically aren't checked for, and we have
maintainers doing sweep removals of these checks, but since we need this
check to ensure proper userspace blktrace functionality we make sure
to annotate the justification for the check.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no need to try instrumenting functions in kernel/stackleak.c.
Otherwise that can cause issues if the cleanup pass of stackleak gcc plugin
is disabled.
The value av7110->debi_virt is stored in DMA memory, and it is assigned
to data, and thus data[0] can be modified at any time by malicious
hardware. In this case, "if (data[0] < 2)" can be passed, but then
data[0] can be changed into a large number, which may cause buffer
overflow when the code "av7110->ci_slot[data[0]]" is used.
To fix this possible bug, data[0] is assigned to a local variable, which
replaces the use of data[0].
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
xive_native_provision_pages() allocates memory and passes the pointer to
OPAL so kmemleak cannot find the pointer usage in the kernel memory and
produces a false positive report (below) (even if the kernel did scan
OPAL memory, it is unable to deal with __pa() addresses anyway).
The original qcom kernel changed the PDM GPIOs to be pull-down
during sleep at some point. Reportedly this was done because
there was some "leakage at PDM outputs during sleep":
Intel Emmitsburg PCH has the same LPSS than Intel Ice Lake.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not called in
error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
The jack on Intel NUC 8 Rugged rear panel doesn't work.
The spec [1] states that the jack supports both headphone and
microphone, so override a Pin Complex which has both Amp-In and Amp-Out
to make the jack work.
Node 0x1b fits the requirement, and user confirmed the jack now works
with new pin config.
HDMI on some platforms doesn't enable audio support because its Port
Connectivity [31:30] is set to AC_JACK_PORT_NONE:
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x58560010: [N/A] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 3
0x02 0x03* 0x04
For now, use a quirk to force connectivity based on SSID. If there are
more platforms affected by the same issue, we can eye for a more generic
solution.
Starting in commit cbc7a6b5a87a ("ASoC: soc-card: add
snd_soc_card_add_dai_link()"), error value from ASoc add_dai_link() is
no longer ignored.
The generic HDA machine driver relied on the old semantics to disable
i915 HDMI/DP audio codec at runtime. If no display codec was present,
add_dai_link() returned an error, but this was ignored and rest of the
card was successfully probed.
Fix the problem by changing the machine driver add_dai_link() to not
return an error in this case.
Fixes: cbc7a6b5a87a ("ASoC: soc-card: add snd_soc_card_add_dai_link()") Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@linux.intel.com> Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> BugLink: https://github.com/thesofproject/linux/issues/2261 Link: https://lore.kernel.org/r/20200714132804.3638221-1-kai.vehmanen@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move collapse_huge_page()'s mmget_still_valid() check into
khugepaged_test_exit() itself. collapse_huge_page() is used for anon THP
only, and earned its mmget_still_valid() check because it inserts a huge
pmd entry in place of the page table's pmd entry; whereas
collapse_file()'s retract_page_tables() or collapse_pte_mapped_thp()
merely clears the page table's pmd entry. But core dumping without mmap
lock must have been as open to mistaking a racily cleared pmd entry for a
page table at physical page 0, as exit_mmap() was. And we certainly have
no interest in mapping as a THP once dumping core.
Fixes: 59ea6d06cfa9 ("coredump: fix race condition between collapse_huge_page() and core dumping") Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Song Liu <songliubraving@fb.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: <stable@vger.kernel.org> [4.8+] Link: http://lkml.kernel.org/r/alpine.LSU.2.11.2008021217020.27773@eggly.anvils Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
binfmt_flat loader uses the gap between text and data to store data
segment pointers for the libraries. Even in the absence of shared
libraries it stores at least one pointer to the executable's own data
segment. Text and data can go back to back in the flat binary image and
without offsetting data segment last few instructions in the text
segment may get corrupted by the data segment pointer.
Fix it by reverting commit a2357223c50a ("binfmt_flat: don't offset the
data start").
Cc: stable@vger.kernel.org Fixes: a2357223c50a ("binfmt_flat: don't offset the data start") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Ungerer <gerg@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Evidently, when I did this previously, we didn't have more than
10 policies and didn't run into the reallocation path, because
it's missing a memset() for the unused policies. Fix that.
Fixes: d07dcf9aadd6 ("netlink: add infrastructure to expose policies to userspace") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy ethtool userspace tool shows an error when no features could
be changed. It's useful to have a netlink reply to be able to show this
error when __netdev_update_features wasn't called, for example:
1. ethtool -k eth0
large-receive-offload: off
2. ethtool -K eth0 rx-fcs on
3. ethtool -K eth0 lro on
Could not change any device features
rx-lro: off [requested on]
4. ethtool -K eth0 lro on
# The output should be the same, but without this patch the kernel
# doesn't send the reply, and ethtool is unable to detect the error.
This commit makes ethtool-netlink always return a reply when requested,
and it still avoids unnecessary calls to __netdev_update_features if the
wanted features haven't changed.
Fixes: 0980bfcd6954 ("ethtool: set netdev features with FEATURES_SET request") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ethtool-netlink ignores dev->hw_features and may confuse the drivers by
asking them to enable features not in the hw_features bitmask. For
example:
1. ethtool -k eth0
tls-hw-tx-offload: off [fixed]
2. ethtool -K eth0 tls-hw-tx-offload on
tls-hw-tx-offload: on
3. ethtool -k eth0
tls-hw-tx-offload: on [fixed]
Fitler out dev->hw_features from req_wanted to fix it and to resemble
the legacy ethtool behavior.
Fixes: 0980bfcd6954 ("ethtool: set netdev features with FEATURES_SET request") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It completely discards the old wanted bits, so they are forgotten with
the next ethtool command. Sample steps to reproduce:
1. ethtool -k eth0
tx-tcp-segmentation: on # TSO is on from the beginning
2. ethtool -K eth0 tx off
tx-tcp-segmentation: off [not requested]
3. ethtool -k eth0
tx-tcp-segmentation: off [requested on]
4. ethtool -K eth0 rx off # Some change unrelated to TSO
5. ethtool -k eth0
tx-tcp-segmentation: off # "Wanted on" is forgotten
This commit fixes it by changing the formula to:
(req_wanted & req_mask) | (old_wanted & ~req_mask),
where old_active was replaced by old_wanted to account for the wanted
bits.
The shortcut condition for the case where nothing was changed now
compares wanted bitmasks, instead of wanted to active.
Fixes: 0980bfcd6954 ("ethtool: set netdev features with FEATURES_SET request") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most statistics in ena driver are incremented, meaning that a stat's
value is a sum of all increases done to it since driver/queue
initialization.
This patch makes all statistics this way, effectively making missed_tx
statistic incremental.
Also added a comment regarding rx_drops and tx_drops to make it
clearer how these counters are calculated.
Fixes: 11095fdb712b ("net: ena: add statistics for missed tx packets") Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__tipc_nl_compat_dumpit() has two callers, and it expects them to
pass a valid nlmsghdr via arg->data. This header is artificial and
crafted just for __tipc_nl_compat_dumpit().
tipc_nl_compat_publ_dump() does so by putting a genlmsghdr as well
as some nested attribute, TIPC_NLA_SOCK. But the other caller
tipc_nl_compat_dumpit() does not, this leaves arg->data uninitialized
on this call path.
Fix this by just adding a similar nlmsghdr without any payload in
tipc_nl_compat_dumpit().
This bug exists since day 1, but the recent commit 6ea67769ff33
("net: tipc: prepare attrs in __tipc_nl_compat_dumpit()") makes it
easier to appear.
Reported-and-tested-by: syzbot+0e7181deafa7e0b79923@syzkaller.appspotmail.com Fixes: d0796d1ef63d ("tipc: convert legacy nl bearer dump to nl compat") Cc: Jon Maloy <jmaloy@redhat.com> Cc: Ying Xue <ying.xue@windriver.com> Cc: Richard Alpe <richard.alpe@ericsson.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__smc_diag_dump() is potentially copying uninitialized kernel stack memory
into socket buffers, since the compiler may leave a 4-byte hole near the
beginning of `struct smcd_diag_dmbinfo`. Fix it by initializing `dinfo`
with memset().
Fixes: 4b1b7d3b30a6 ("net/smc: add SMC-D diag support") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of output and input streams was never being reduced, eg when
processing received INIT or INIT_ACK chunks.
The effect is that DATA chunks can be sent with invalid stream ids
and then discarded by the remote system.
Fixes: 2075e50caf5ea ("sctp: convert to genradix") Signed-off-by: David Laight <david.laight@aculab.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcf_ct_handle_fragments() shouldn't free the skb when ip_defrag() call
fails. Otherwise, we will cause a double-free bug.
In such cases, just return the error to the caller.
Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct") Signed-off-by: Alaa Hleihel <alaa@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing large uint32 sockaddr_qrtr.port numbers for port allocation
triggers a warning within idr_alloc() since the port number is cast
to int, and thus interpreted as a negative number. This leads to
the rejection of such valid port numbers in qrtr_port_assign() as
idr_alloc() fails.
To avoid the problem, switch to idr_alloc_u32() instead.
Fixes: bdabad3e363d ("net: Add Qualcomm IPC router") Reported-by: syzbot+f31428628ef672716ea8@syzkaller.appspotmail.com Signed-off-by: Necip Fazil Yildiran <necip@google.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the nexthop code will use an empty NHA_GROUP attribute, but it
requires at least 1 entry in order to function properly. Otherwise we
end up derefencing null or random pointers all over the place due to not
having any nh_grp_entry members allocated, nexthop code relies on having at
least the first member present. Empty NHA_GROUP doesn't make any sense so
just disallow it.
Also add a WARN_ON for any future users of nexthop_create_group().
CC: David Ahern <dsahern@gmail.com> Fixes: 430a049190de ("nexthop: Add support for nexthop groups") Reported-by: syzbot+a61aa19b0c14c8770bd9@syzkaller.appspotmail.com Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may access the two bytes after vlan_hdr in vlan_set_encap_proto(). So
we should pull VLAN_HLEN + sizeof(unsigned short) in skb_vlan_untag() or
we may access the wrong data.
Fixes: 0d5501c1c828 ("net: Always untag vlan-tagged traffic on input.") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving an IPv4 packet inside an IPv6 GRE packet, and the
IP6_TNL_F_RCV_DSCP_COPY flag is set on the tunnel, the IPv4 header would
get corrupted. This is due to the common ip6_tnl_rcv() function assuming
that the inner header is always IPv6. This patch checks the tunnel
protocol for IPv4 inner packets, but still defaults to IPv6.
Fixes: 308edfdf1563 ("gre6: Cleanup GREv6 receive path, call common GRE functions") Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This breaks display wake up in stable kernels (5.7.x and 5.8.x).
Note that there is no upstream equivalent to this
revert. This patch was targeted for stable by Sasha's stable
patch process. Presumably there are some other changes necessary
for this patch to work properly on stable kernels.
When an MMU notifier call results in unmapping a range that spans multiple
PGDs, we end up calling into cond_resched_lock() when crossing a PGD boundary,
since this avoids running into RCU stalls during VM teardown. Unfortunately,
if the VM is destroyed as a result of OOM, then blocking is not permitted
and the call to the scheduler triggers the following BUG():
The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the
case of kvm_mmu_notifier_invalidate_range_start(), this field is not
forwarded on to the architecture-specific implementation of
kvm_unmap_hva_range() and therefore the backend cannot sensibly decide
whether or not to block.
Add an extra 'flags' parameter to kvm_unmap_hva_range() so that
architectures are aware as to whether or not they are permitted to block.
Cc: <stable@vger.kernel.org> Cc: Marc Zyngier <maz@kernel.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-2-will@kernel.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Treat a NULL cmdline the same as empty. Although this is unlikely to
happen in practice, the x86 kernel entry does check for NULL cmdline and
handles it, so do it here as well.
When remapping the kernel rodata section RO in the EFI pagetables, the
protection flags that were used for the text section are being reused,
but the rodata section should not be marked executable.
IA32_MCG_STATUS.RIPV indicates whether the return RIP value pushed onto
the stack as part of machine check delivery is valid or not.
Various drivers copied a code fragment that uses the RIPV bit to
determine the severity of the error as either HW_EVENT_ERR_UNCORRECTED
or HW_EVENT_ERR_FATAL, but this check is reversed (marking errors where
RIPV is set as "FATAL").
Reverse the tests so that the error is marked fatal when RIPV is not set.
As per PAPR we have to look for both EPOW sensor value and event
modifier to identify the type of event and take appropriate action.
In LoPAPR v1.1 section 10.2.2 includes table 136 "EPOW Action Codes":
SYSTEM_SHUTDOWN 3
The system must be shut down. An EPOW-aware OS logs the EPOW error
log information, then schedules the system to be shut down to begin
after an OS defined delay internal (default is 10 minutes.)
Then in section 10.3.2.2.8 there is table 146 "Platform Event Log
Format, Version 6, EPOW Section", which includes the "EPOW Event
Modifier":
For EPOW sensor value = 3
0x01 = Normal system shutdown with no additional delay
0x02 = Loss of utility power, system is running on UPS/Battery
0x03 = Loss of system critical functions, system should be shutdown
0x04 = Ambient temperature too high
All other values = reserved
We have a user space tool (rtas_errd) on LPAR to monitor for
EPOW_SHUTDOWN_ON_UPS. Once it gets an event it initiates shutdown
after predefined time. It also starts monitoring for any new EPOW
events. If it receives "Power restored" event before predefined time
it will cancel the shutdown. Otherwise after predefined time it will
shutdown the system.
Commit 79872e35469b ("powerpc/pseries: All events of
EPOW_SYSTEM_SHUTDOWN must initiate shutdown") changed our handling of
the "on UPS/Battery" case, to immediately shutdown the system. This
breaks existing setups that rely on the userspace tool to delay
shutdown and let the system run on the UPS.
Fixes: 79872e35469b ("powerpc/pseries: All events of EPOW_SYSTEM_SHUTDOWN must initiate shutdown") Cc: stable@vger.kernel.org # v4.0+ Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
[mpe: Massage change log and add PAPR references] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200820061844.306460-1-hegdevasant@linux.vnet.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding a new fd to an epoll, and that this new fd is an
epoll fd itself, we recursively scan the fds attached to it
to detect cycles, and add non-epool files to a "check list"
that gets subsequently parsed.
However, this check list isn't completely safe when deletions
can happen concurrently. To sidestep the issue, make sure that
a struct file placed on the check list sees its f_count increased,
ensuring that a concurrent deletion won't result in the file
disapearing from under our feet.
Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
b53_common.c:1583:13: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ent.port &= ~BIT(port);
~~~~~~~~ ^
ent is set by a successful call to b53_arl_read(). Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.
So add -ETIMEDOUT to the switch statement. Because
b53_arl_op_wait() already prints out a message, do not add another
one.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by: Tom Rix <trix@redhat.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
