Consider an amba driver with a .probe but without a .remove callback (e.g.
pl061_gpio_driver). The function amba_probe() is called to bind a device
and so dev_pm_domain_attach() and others are called. As there is no remove
callback amba_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.
To fix this always use the core driver callbacks and handle missing amba
callbacks there. For probe refuse registration as a driver without probe
doesn't make sense.
Fixes: 7cfe249475fd ("ARM: AMBA: Add pclk support to AMBA bus infrastructure") Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20210126165835.687514-2-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.
Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:
Uncompressing Linux... done, booting the kernel.
The reason is that it clears nTLSMD bit when disabling caches:
nTLSMD, bit [3]
When ARMv8.2-LSMAOC is implemented:
No Trap Load Multiple and Store Multiple to
Device-nGRE/Device-nGnRE/Device-nGnRnE memory.
0b0 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
generate a stage 1 Alignment fault.
0b1 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.
This bit is permitted to be cached in a TLB.
This field resets to 1.
Otherwise:
Reserved, RES1
So as effect we start getting traps we are not quite ready for.
Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.
Fixes: 7d09e85448dfa78e3e58186c934449aaf6d49b50 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format") Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
These are only used locally. It fixes these W=1 compile errors :
../arch/powerpc/kvm/powerpc.c:1521:5: error: no previous prototype for ‘kvmppc_get_vmx_dword’ [-Werror=missing-prototypes]
1521 | int kvmppc_get_vmx_dword(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1539:5: error: no previous prototype for ‘kvmppc_get_vmx_word’ [-Werror=missing-prototypes]
1539 | int kvmppc_get_vmx_word(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1557:5: error: no previous prototype for ‘kvmppc_get_vmx_hword’ [-Werror=missing-prototypes]
1557 | int kvmppc_get_vmx_hword(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1575:5: error: no previous prototype for ‘kvmppc_get_vmx_byte’ [-Werror=missing-prototypes]
1575 | int kvmppc_get_vmx_byte(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~
Fixes: acc9eb9305fe ("KVM: PPC: Reimplement LOAD_VMX/STORE_VMX instruction mmio emulation with analyse_instr() input") Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210104143206.695198-19-clg@kaod.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, polling a umad device will always works, even if the device was
disassociated. A disassociated device should immediately return EPOLLERR
from poll(). Otherwise userspace is endlessly hung on poll() with no idea
that the device has been removed from the system.
MAD message received by the user has EINVAL error in all flows
including when the device is disassociated. That makes it impossible
for the applications to treat such flow differently.
Change it to return EIO, so the applications will be able to perform
disassociation recovery.
With my version of GCC 9.3.1 the ".cold" subfunctions no longer have a
numbered suffix, so the trailing period is no longer there.
Presumably this doesn't yet trigger a user-visible bug since most of the
subfunction detection logic is duplicated. I only found it when
testing vmlinux.o validation.
Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.
Commit ff268b56ce8c ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.
Commit c33d442328f5 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:
[ 26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!
There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.
Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.
Fixes: c33d442328f5 ("debugfs: make error message a bit more verbose") Cc: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device node reference obtained with of_get_child_by_name() should be
dropped on error paths.
Fixes: 26aec009f6b6 ("regulator: add device tree support for s5m8767") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20210121155914.48034-1-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
KEY_FLAG_KEEP is not meant to be passed to keyring_alloc() or key_alloc(),
as these only take KEY_ALLOC_* flags. KEY_FLAG_KEEP has the same value as
KEY_ALLOC_BYPASS_RESTRICTION, but fortunately only key_create_or_update()
uses it. LSMs using the key_alloc hook don't check that flag.
KEY_FLAG_KEEP is then ignored but fortunately (again) the root user cannot
write to the blacklist keyring, so it is not possible to remove a key/hash
from it.
Fix this by adding a KEY_ALLOC_SET_KEEP flag that tells key_alloc() to set
KEY_FLAG_KEEP on the new key. blacklist_init() can then, correctly, pass
this to keyring_alloc().
We can also use this in ima_mok_init() rather than setting the flag
manually.
Note that this doesn't fix an observable bug with the current
implementation but it is required to allow addition of new hashes to the
blacklist in the future without making it possible for them to be removed.
Fixes: 734114f8782f ("KEYS: Add a system blacklist keyring") Reported-by: Mickaël Salaün <mic@linux.microsoft.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Mickaël Salaün <mic@linux.microsoft.com>
cc: Mimi Zohar <zohar@linux.vnet.ibm.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Decrements the reference count of device node and its child node.
Fixes: dfe7a1b058bb ("regulator: AXP20x: Add support for regulators subsystem") Signed-off-by: Pan Bian <bianpan2016@163.com> Link: https://lore.kernel.org/r/20210120123313.107640-1-bianpan2016@163.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While comparing clocks between the H6 and H616, some of the M factor
ranges were found to be wrong: the manual says they are only covering
two bits [1:0], but our code had "5" in the number-of-bits field.
By writing 0xff into that register in U-Boot and via FEL, it could be
confirmed that bits [4:2] are indeed masked off, so the manual is right.
Change to number of bits in the affected clock's description.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210118000912.28116-1-andre.przywara@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the device tree is incorrectly configured, and attempts to
define a "no-map" reserved memory that overlaps with the kernel
data/code, the kernel would crash quickly after boot, with no
obvious clue about the nature of the issue.
And we declare a no-map shared-dma-pool region at a fixed address
within that range:
mem_reserved: mem_region {
compatible = "shared-dma-pool";
reg = <0 0x40000000 0 0x01A00000>;
no-map;
};
To fix this, when removing memory regions at early boot (which is
what "no-map" regions do), we need to make sure that the memory
is not already reserved. If we do, __reserved_mem_reserve_reg
will throw an error:
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory
for node 'mem_region': base 0x0000000040000000, size 26 MiB
and the code that will try to use the region should also fail,
later on.
We do not do anything for non-"no-map" regions, as memblock
explicitly allows reserved regions to overlap, and the commit
that this fixes removed the check for that precise reason.
[ qperret: fixed conflicts caused by the usage of memblock_mark_nomap ]
Fixes: 094cb98179f19b7 ("of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Quentin Perret <qperret@google.com> Link: https://lore.kernel.org/r/20210115114544.1830068-3-qperret@google.com Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Mark the memory region with NOMAP flag instead of completely removing it
from the memory blocks. That makes the FDT handling consistent with the EFI
memory map handling.
Cc: Rob Herring <robh+dt@kernel.org> Cc: Frank Rowand <frowand.list@gmail.com> Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de> Signed-off-by: Quentin Perret <qperret@google.com> Link: https://lore.kernel.org/r/20210115114544.1830068-2-qperret@google.com Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On Intel Tangier B0 and Anniedale the interrupt line, disregarding
to have different numbers, is shared between HSU DMA and UART IPs.
Thus on such SoCs we are expecting that IRQ handler is called in
UART driver only. hsu_pci_irq was handling the spurious interrupt
from HSU DMA by returning immediately. This wastes CPU time and
since HSU DMA and HSU UART interrupt occur simultaneously they race
to be handled causing delay to the HSU UART interrupt handling.
Fix this by disabling the interrupt entirely.
During connection setup, the application may choose to zero-size inbound
and outbound READ queues, as well as the Receive queue. This patch fixes
handling of zero-sized queues, but not prevents it.
Kamal Heib says in an initial error report:
When running the blktests over siw the following shift-out-of-bounds is
reported, this is happening because the passed IRD or ORD from the ulp
could be zero which will lead to unexpected behavior when calling
roundup_pow_of_two(), fix that by blocking zero values of ORD or IRD.
Prevent invalid (0, 0) inputs to hid-core's snto32() function.
Maybe it is just the dummy device here that is causing this, but
there are hundreds of calls to snto32(0, 0). Having n (bits count)
of 0 is causing the current UBSAN trap with a shift value of
0xffffffff (-1, or n - 1 in this function).
Either of the value to shift being 0 or the bits count being 0 can be
handled by just returning 0 to the caller, avoiding the following
complex shift + OR operations:
return value & (1 << (n - 1)) ? value | (~0U << n) : value;
The CEC clock on the H6 SoC is a bit special, since it uses a fixed
pre-dividier for one source clock (the PLL), but conveys the other clock
(32K OSC) directly.
We are using a fixed predivider array for that, but fail to use the right
flag to actually activate that.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU") Reported-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210106143246.11255-1-andre.przywara@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.
Fixes: 140623410536 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller") Signed-off-by: Pratyush Yadav <p.yadav@ti.com> Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IS_OFFSET register contains the interrupt status bits which will be
set regardless of the enabling of the corresponding interrupt condition.
One must therefore look at both IS_OFFSET and IE_OFFSET to determine
whether an interrupt condition is set and enabled.
Fixes: c245d94ed106 ("i2c: iproc: Add multi byte read-write support for slave mode") Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Acked-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error codes returned by meson_clk_get_pll_settings() are all
negative. Make "ret" a signed integer in meson_clk_pll_set_rate() to
make it match with the clk_ops.set_rate API as well as the data type
returned by meson_clk_get_pll_settings().
The "rate" parameter in meson_clk_pll_set_rate() contains the new rate.
Retrieve the old rate with clk_hw_get_rate() so we don't inifinitely try
to switch from the new rate to the same rate again.
Fixes: 7a29a869434e8b ("clk: meson: Add support for Meson clock controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20201226121556.975418-2-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
The v3 file capabilities have a uid field that records the filesystem
uid of the root user of the user namespace the file capabilities are
valid in.
When someone is silly enough to have the same underlying uid as the
root uid of multiple nested containers a v3 filesystem capability can
be ambiguous.
In the spirit of don't do that then, forbid writing a v3 filesystem
capability if it is ambiguous.
Fixes: 8db6c34f1dbc ("Introduce v3 namespaced file capabilities") Reviewed-by: Andrew G. Morgan <morgan@kernel.org> Reviewed-by: Serge Hallyn <serge@hallyn.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fs/jffs2/summary.c:794:31: warning: Use of memory after it is freed
c->summary->sum_list_head = temp->u.next;
^~~~~~~~~~~~
In jffs2_sum_write_data(), in a loop summary data is handles a node at
a time. When it has written out the node it is removed the summary list,
and the node is deleted. In the corner case when a
JFFS2_FEATURE_RWCOMPAT_COPY is seen, a call is made to
jffs2_sum_disable_collecting(). jffs2_sum_disable_collecting() deletes
the whole list which conflicts with the loop's deleting the list by parts.
To preserve the old behavior of stopping the write midway, bail out of
the loop after disabling summary collection.
Fixes: 6171586a7ae5 ("[JFFS2] Correct handling of JFFS2_FEATURE_RWCOMPAT_COPY nodes.") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit integer. In the case where
l2nb is 32 or more this can lead to an overflow. Avoid this by shifting
the value 1LL instead.
Addresses-Coverity: ("Uninitentional integer overflow") Fixes: b40c2e665cd5 ("fs/jfs: TRIM support for JFS Filesystem") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If "clocks = <&xxx>" is specified from the CPU or Codec component
device node, the clock is not getting enabled. Thus audio playback
or capture fails.
Fix this by populating "simple_dai->clk" field when clocks property
is specified from device node as well. Also tidy up by re-organising
conditional statements of parsing logic.
IMA allocates kernel virtual memory to carry forward the measurement
list, from the current kernel to the next kernel on kexec system call,
in ima_add_kexec_buffer() function. This buffer is not freed before
completing the kexec system call resulting in memory leak.
Add ima_buffer field in "struct kimage" to store the virtual address
of the buffer allocated for the IMA measurement list.
Free the memory allocated for the IMA measurement list in
kimage_file_post_load_cleanup() function.
IMA allocates kernel virtual memory to carry forward the measurement
list, from the current kernel to the next kernel on kexec system call,
in ima_add_kexec_buffer() function. In error code paths this memory
is not freed resulting in memory leak.
Free the memory allocated for the IMA measurement list in
the error code paths in ima_add_kexec_buffer() function.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com> Suggested-by: Tyler Hicks <tyhicks@linux.microsoft.com> Fixes: 7b8589cc29e7 ("ima: on soft reboot, save the measurement list") Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The length ('len' parameter) passed to crypto_ecdh_decode_key() is never
checked against the length encoded in the passed buffer ('buf'
parameter). This could lead to an out-of-bounds access when the passed
length is less than the encoded length.
Return value in __load_free_space_cache is not properly set after
(unlikely) memory allocation failures and 0 is returned instead.
This is not a problem for the caller load_free_space_cache because only
value 1 is considered as 'cache loaded' but for clarity it's better
to set the errors accordingly.
Fixes: a67509c30079 ("Btrfs: add a io_ctl struct and helpers for dealing with the space cache") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function simple_write_to_buffer() doesn't add string termination
at the end of buf, we need to handle it on our own. This change refers
to the function tokenize_input() in debug.c and the function
sof_dfsentry_trace_filter_write() in trace.c.
Fixes: 091c12e1f50c ("ASoC: SOF: debug: add new debugfs entries for IPC flood test") Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20210208103857.75705-1-hui.wang@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When channel->device_obj is non-NULL, vmbus_onoffer_rescind() could
invoke put_device(), that will eventually release the device and free
the channel object (cf. vmbus_device_release()). However, a pointer
to the object is dereferenced again later to load the primary_channel.
The use-after-free can be avoided by noticing that this load/check is
redundant if device_obj is non-NULL: primary_channel must be NULL if
device_obj is non-NULL, cf. vmbus_add_channel_work().
Fixes: 54a66265d6754b ("Drivers: hv: vmbus: Fix rescind handling") Reported-by: Juan Vazquez <juvazq@microsoft.com> Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20201209070827.29335-5-parri.andrea@gmail.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the user passes a "level" value which is higher than 31 then that
leads to shift wrapping. The undefined behavior will lead to a
syzkaller stack dump.
Fixes: 5632708f4452 ("drm/amd/powerplay: add dpm force multiple levels on cz/tonga/fiji/polaris (v2)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Occasionally, quota data may be corrupted detected by fsck:
Info: checkpoint state = 45 : crc compacted_summary unmount
[QUOTA WARNING] Usage inconsistent for ID 0:actual (1543036928, 762) != expected (1543032832, 762)
[ASSERT] (fsck_chk_quota_files:1986) --> Quota file is missing or invalid quota file content found.
[QUOTA WARNING] Usage inconsistent for ID 0:actual (1352478720, 344) != expected (1352474624, 344)
[ASSERT] (fsck_chk_quota_files:1986) --> Quota file is missing or invalid quota file content found.
[FSCK] Unreachable nat entries [Ok..] [0x0]
[FSCK] SIT valid block bitmap checking [Ok..]
[FSCK] Hard link checking for regular file [Ok..] [0x0]
[FSCK] valid_block_count matching with CP [Ok..] [0xdf299]
[FSCK] valid_node_count matcing with CP (de lookup) [Ok..] [0x2b01]
[FSCK] valid_node_count matcing with CP (nat lookup) [Ok..] [0x2b01]
[FSCK] valid_inode_count matched with CP [Ok..] [0x2665]
[FSCK] free segment_count matched with CP [Ok..] [0xcb04]
[FSCK] next block offset is free [Ok..]
[FSCK] fixing SIT types
[FSCK] other corrupted bugs [Fail]
The root cause is:
If we open file w/ readonly flag, disk quota info won't be initialized
for this file, however, following mmap() will force to convert inline
inode via f2fs_convert_inline_inode(), which may increase block usage
for this inode w/o updating quota data, it causes inconsistent disk quota
info.
The issue will happen in following stack:
open(file, O_RDONLY)
mmap(file)
- f2fs_convert_inline_inode
- f2fs_convert_inline_page
- f2fs_reserve_block
- f2fs_reserve_new_block
- f2fs_reserve_new_blocks
- f2fs_i_blocks_write
- dquot_claim_block
inode->i_blocks increase, but the dqb_curspace keep the size for the dquots
is NULL.
To fix this issue, let's call dquot_initialize() anyway in both
f2fs_truncate() and f2fs_convert_inline_inode() functions to avoid potential
inconsistent quota data issue.
Fixes: 0abd675e97e6 ("f2fs: support plain user/group quota") Signed-off-by: Daiyue Zhang <zhangdaiyue1@huawei.com> Signed-off-by: Dehe Gu <gudehe@huawei.com> Signed-off-by: Junchao Jiang <jiangjunchao1@huawei.com> Signed-off-by: Ge Qiu <qiuge@huawei.com> Signed-off-by: Yi Chen <chenyi77@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the case of failure while parsing the partitions, the iterator should
be pre decremented by one before starting to free the memory allocated
by kstrdup(). Because in the failure case, kstrdup() will not succeed
and thus no memory will be allocated for the current iteration.
The correct mask is 0x1f8 (Bit 3-8), but due to missing BIT() 0xf (Bit
0-3) was set instead. This means setting of CPCAP_BIT_MIC1_RX_TIMESLOT0
(Bit 3) still worked (part of both masks). On the other hand the code
does not properly clear the other MIC timeslot bits. I think this
is not a problem, since they are probably initialized to 0 and not
touched by the driver anywhere else. But the mask also contains some
wrong bits, that will be cleared. Bit 0 (CPCAP_BIT_SMB_CDC) should be
safe, since the driver enforces it to be 0 anyways.
Bit 1-2 are CPCAP_BIT_FS_INV and CPCAP_BIT_CLK_INV. This means enabling
audio recording forces the codec into SND_SOC_DAIFMT_NB_NF mode, which
is obviously bad.
The bug probably remained undetected, because there are not many use
cases for routing microphone to the CPU on platforms using cpcap and
user base is small. I do remember having some issues with bad sound
quality when testing voice recording back when I wrote the driver.
It probably was this bug.
Fixes: f6cdf2d3445d ("ASoC: cpcap: new codec") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Reviewed-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210123172945.3958622-1-sre@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reworking the resources management and departing from using
ahci_platform_enable_resources() which did not allow a proper step
separation like we need, we unfortunately lost the ability to control
AHCI regulators. This broke some Broadcom STB systems that do expect
regulators to be turned on to link up with attached hard drives.
Talitos Security Engine AESU considers any input
data size that is not a multiple of 16 bytes to be an error.
This is not a problem in general, except for Counter mode
that is a stream cipher and can have an input of any size.
Test Manager for ctr(aes) fails on 4th test vector which has
a length of 499 while all previous vectors which have a 16 bytes
multiple length succeed.
As suggested by Freescale, round up the input data length to the
nearest 16 bytes.
If the task is pinned to a cpu, setting the misfit status means that
we'll unnecessarily continuously attempt to migrate the task but fail.
This continuous failure will cause the balance_interval to increase to
a high value, and eventually cause unnecessary significant delays in
balancing the system when real imbalance happens.
Caught while testing uclamp where rt-app calibration loop was pinned to
cpu 0, shortly after which we spawn another task with high util_clamp
value. The task was failing to migrate after over 40ms of runtime due to
balance_interval unnecessary expanded to a very high value from the
calibration loop.
Not done here, but it could be useful to extend the check for pinning to
verify that the affinity of the task has a cpu that fits. We could end
up in a similar situation otherwise.
The Renkforce RF AC4K 300 Action Cam 4K reports invalid bFormatIndex and
bFrameIndex values when negotiating the video probe and commit controls.
The UVC descriptors report a single supported format and frame size,
with bFormatIndex and bFrameIndex both equal to 2, but the video probe
and commit controls report bFormatIndex and bFrameIndex set to 1.
The device otherwise operates correctly, but the driver rejects the
values and fails the format try operation. Fix it by ignoring the
invalid indices, and assuming that the format and frame requested by the
driver are accepted by the device.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210767 Fixes: 8a652a17e3c0 ("media: uvcvideo: Ensure all probed info is returned to v4l2") Reported-by: Till Dörges <doerges@pre-sense.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/media/platform/pxa_camera.c:1410:7: error:
‘i’ undeclared (first use in this function)
for (i = 0; i < vb->num_planes; i++)
^
The variable 'i' is missing, so declare it.
Fixes: 6f28435d1c15 ("[media] media: platform: pxa_camera: trivial move of functions") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
However, if 'risc->cpu != NULL', the memory will be freed, but never
reallocated with the bigger 'size'.
Explicitly set 'risc->cpu' to NULL, so that the reallocation is
correctly performed a few lines below.
The software_node_get_next_child() function currently does not hold
references to the child software_node that it finds or put the ref that
is held against the old child - fix that.
Fixes: 59abd83672f7 ("drivers: base: Introducing software nodes to the firmware node framework") Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Scally <djrscally@gmail.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes corrupted display output in HDMI deep color
10/12 bpc mode at least as observed on AMD Mullins, DCE-8.3.
It will hopefully also provide fixes for other DCE's up to
DCE-11, assuming those will need similar fixes, but i could
not test that for HDMI due to lack of suitable hw, so viewer
discretion is advised.
dce110_stream_encoder_hdmi_set_stream_attribute() is used for
HDMI setup on all DCE's and is missing color_depth assignment.
dce110_program_pix_clk() is used for pixel clock setup on HDMI
for DCE 6-11, and is missing color_depth assignment.
Additionally some of the underlying Atombios specific encoder
and pixelclock setup functions are missing code which is in
the classic amdgpu kms modesetting path and the in the radeon
kms driver for DCE6/DCE8.
encoder_control_digx_v3() - Was missing setup code wrt. amdgpu
and radeon kms classic drivers. Added here, but untested due to
lack of suitable test hw.
encoder_control_digx_v4() - Added missing setup code.
Successfully tested on AMD mullins / DCE-8.3 with HDMI deep color
output at 10 bpc and 12 bpc.
Note that encoder_control_digx_v5() has proper setup code in place
and is used, e.g., by DCE-11.2, but this code wasn't used for deep
color setup due to the missing cntl.color_depth setup in the calling
function for HDMI.
set_pixel_clock_v5() - Missing setup code wrt. classic amdgpu/radeon
kms. Added here, but untested due to lack of hw.
set_pixel_clock_v6() - Missing setup code added. Successfully tested
on AMD mullins DCE-8.3. This fixes corrupted display output at HDMI
deep color output with 10 bpc or 12 bpc.
Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)") Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In set_clamp(), the comments and definitions for the COLOR_DEPTH_101010
and COLOR_DEPTH_121212 cases directly contradict the code comment which
explains how this should work, whereas the COLOR_DEPTH_888 case
is consistent with the code comments. Comment says the bitmask should
be chosen to align to the top-most 10 or 12 MSB's on a 14 bit bus, but
the implementation contradicts that: 10 bit case sets a mask for 12 bpc
clamping, whereas 12 bit case sets a mask for 14 bpc clamping.
Note that during my limited testing on DCE-8.3 (HDMI deep color)
and DCE-11.2 (DP deep color), this didn't have any obvious ill
effects, neither did fixing it change anything obvious for the
better, so this fix may be inconsequential on DCE, and just
reduce the confusion of innocent bystanders when reading the code
and trying to investigate problems with 10 bpc+ output.
Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)") Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 866b6a89c6d1 ("MIPS: Add DWARF unwinding to assembly") added
-fno-asynchronous-unwind-tables to KBUILD_CFLAGS to prevent compiler
from emitting .eh_frame symbols.
However, as MIPS heavily uses CFI, that's not enough. Use the
approach taken for x86 (as it also uses CFI) and explicitly put CFI
symbols into the .debug_frame section (except for VDSO).
This allows us to drop .eh_frame from DISCARDS as it's no longer
being generated.
During commit 88bc4178568b ("drm: Use new
DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags") DRM_BUS_FLAG_*
macros have been changed to avoid ambiguity but just because of this
ambiguity previous DRM_BUS_FLAG_PIXDATA_(POS/NEG)EDGE were used meaning
_SAMPLE_ not _DRIVE_. This leads to DLCK inversion and need to fix but
instead of swapping phase values, let's adopt an easier approach Maxime
suggested:
It turned out that bit 26 of SUN4I_TCON0_IO_POL_REG is dedicated to
invert DCLK polarity and this makes things really easier than before. So
let's handle DCLK polarity by adding SUN4I_TCON0_IO_POL_DCLK_DRIVE_NEGEDGE
as bit 26 and activating according to bus_flags the same way it is done
for all the other signals polarity.
Renaming 'struct device_private' to 'struct bcm_device_private',
because it clashes with 'struct device_private' from
'drivers/base/base.h'.
While it's not a functional problem, it's causing two distinct
type hierarchies in BTF data. It also breaks build with options:
CONFIG_DEBUG_INFO_BTF=y
CONFIG_CRYPTO_DEV_BCM_SPU=y
There are two issues with this code. The first error path forgot to set
the error code and instead returns success. The second error path
doesn't clean up.
Fixes: 272b5edd3b8f ("ASoC: Add support for CS42L56 CODEC") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/X9NE/9nK9/TuxuL+@mwanda Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kzalloc() fails, em28xx_uninit_usb_xfer() will free
usb_bufs->buf and set it to NULL. Thus the later access
to usb_bufs->buf[i] will lead to null pointer dereference.
Also the kfree(usb_bufs->buf) after that is redundant.
Fixes: d571b592c6206 ("media: em28xx: don't use coherent buffer for DMA transfers") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The csc/scaler device private struct is released by
ipu_csc_scaler_video_device_release(), which can be called
by video_unregister_device() if there are no users
of the underlying struct video device.
Therefore, the mutex can't be held when calling
video_unregister_device() as its memory may be freed
by it, leading to a kernel oops.
Fortunately, the fix is quite simple as no locking
is needed when calling video_unregister_device(): v4l2-core
already has its own internal locking, and the structures
are also properly refcounted.
The csc/scaler device pointer (imxmd->m2m_vdev) is assigned
after the imx media device v4l2-async probe completes,
therefore we need to check if the device is non-NULL
before trying to unregister it.
This can be the case if the non-completed imx media device
is unbinded (or the driver is removed), leading to a kernel oops.
The driver currently reports a single supported value for
V4L2_CID_PIXEL_RATE and initializes the control's minimum value to 0,
which is very risky, as userspace might accidentally use it as divider
when calculating the time duration of a line.
Fix this by using as minimum the only supported value when registering
the control.
arch/mips/lantiq/irq.c:305:48: error: use of logical '&&' with constant
operand [-Werror,-Wconstant-logical-operand]
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
^ ~~~~~~~~~~~~~~~~~
arch/mips/lantiq/irq.c:305:48: note: use '&' for a bitwise operation
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
^~
&
arch/mips/lantiq/irq.c:305:48: note: remove constant to silence this
warning
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
~^~~~~~~~~~~~~~~~~~~~
1 error generated.
Explicitly compare the constant LTQ_EBU_PCC_ISTAT against 0 to fix the
warning. Additionally, remove the unnecessary parentheses as this is a
simple conditional statement and shorthand '== 0' to '!'.
When building with clang, the following section mismatch warning occurs:
WARNING: modpost: vmlinux.o(.text+0x24490): Section mismatch in
reference from the function r4k_cache_init() to the function
.init.text:loongson2_sc_init()
This should have been fixed with commit ad4fddef5f23 ("mips: fix Section
mismatch in reference") but it was missed. Remove the improper __init
annotation like that commit did.
Commit 69b6f2e817e5b ("crypto: arm64/aes-neon - limit exposed routines if
faster driver is enabled") intended to hide modes from the plain NEON
driver that are also implemented by the faster bit sliced NEON one if
both are enabled. However, the defined() CPP function does not detect
if the bit sliced NEON driver is enabled as a module. So instead, let's
use IS_ENABLED() here.
With the recent kmap change, some tests which were conditional on
CONFIG_DEBUG_HIGHMEM now are enabled by default.
This permit to detect a problem in sun4i-ss usage of kmap.
sun4i-ss uses two kmap via sg_miter (one for input, one for output), but
using two kmap at the same time is hard:
"the ordering has to be correct and with sg_miter that's probably hard to get
right." (quoting Tlgx)
So the easiest solution is to never have two sg_miter/kmap open at the same time.
After each use of sg_miter, I store the current index, for being able to
resume sg_miter to the right place.
The main problem with this error handling was that it didn't clean up if
i2c_add_numbered_adapter() failed. This code is pretty old, and doesn't
match with today's checkpatch.pl standards so I took the opportunity to
tidy it up a bit. I changed the NULL comparison, and removed the
WARNING message if kzalloc() fails and updated the label names.
projects / thirdparty / kernel / stable.git / log
