num-cs is 32 bit property, don't read just upper 16 bits.
Fixes: 4a8573abe965 (spi: qup: Remove chip select function) Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Mark Brown <broonie@kernel.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
global_update_bandwidth() uses static variable update_time as the
timestamp for the last update but forgets to initialize it to
INITIALIZE_JIFFIES.
This means that global_dirty_limit will be 5 mins into the future on
32bit and some large amount jiffies into the past on 64bit. This
isn't critical as the only effect is that global_dirty_limit won't be
updated for the first 5 mins after booting on 32bit machines,
especially given the auxiliary nature of global_dirty_limit's role -
protecting against global dirty threshold's sudden dips; however, it
does lead to unintended suboptimal behavior. Fix it.
Fixes: c42843f2f0bb ("writeback: introduce smoothed global dirty limit") Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Jan Kara <jack@suse.cz> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
As the sunxi usb clocks all contain a reset controller, it is not
possible to build the sunxi clock driver without RESET_CONTROLLER
enabled. Doing so results in an undefined symbol error:
drivers/built-in.o: In function `sunxi_gates_clk_setup':
linux/drivers/clk/sunxi/clk-sunxi.c:1071: undefined reference to
`reset_controller_register'
This is possible if building a minimal kernel without PHY_SUN4I_USB.
The dependency issue is made visible at compile time instead of
link time by the new A80 mmc clocks, which also use a reset control
itself.
This patch makes ARCH_SUNXI select ARCH_HAS_RESET_CONTROLLER and
RESET_CONTROLLER.
Fixes: 559482d1f950 ARM: sunxi: Split the various SoCs support in Kconfig Reported-by: Lourens Rozema <ik@lourensrozema.nl> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[ luis: backported to 3.16:
- dropped changes to sun8i and sun9i, unsupported on 3.16 kernel ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The 8250_dw i/o accessors try to write a console error message if the
LCR workaround was unsuccessful. When the port->lock is already held
(eg., when called from serial8250_set_termios()), this deadlocks.
Make the error message a FIXME until a general solution is devised.
Cc: Tim Kryger <tim.kryger@gmail.com> Reported-by: Zhang Zhen <zhenzhang.zhang@huawei.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16:
- dropped changes to dw8250_serial_outq() ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.
BugLink: https://bugs.launchpad.net/bugs/1436745 Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The hrtimer_{start/cancel} functions call into tracing which uses RCU.
But it is not legal to call into RCU in cpuidle because it is one of the
quiescent states. Hence protect this region with RCU_NONIDLE which informs
RCU that the cpu is momentarily non-idle.
As an aside it is helpful to point out that the clock event device that is
programmed here is not a per-cpu clock device; it is a
pseudo clock device, used by the broadcast framework alone.
The per-cpu clock device programming never goes through bc_set_next().
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: linuxppc-dev@ozlabs.org Cc: mpe@ellerman.id.au Cc: tglx@linutronix.de Link: http://lkml.kernel.org/r/20150318104705.17763.56668.stgit@preeti.in.ibm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 746c9e9f92dd "of/base: Fix PowerPC address parsing hack" limited
the applicability of the workaround whereby a missing ranges is treated
as an empty ranges. This workaround was hiding a bug in the etsec2
device tree nodes, which have children with reg, but did not have
ranges.
Signed-off-by: Scott Wood <scottwood@freescale.com> Reported-by: Alexander Graf <agraf@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
After d905c5df9aef ("PPC: POWERNV: move iommu_add_device earlier"), the
refcnt on the kobject backing the IOMMU group for a PCI device is
elevated by each call to pci_dma_dev_setup_pSeriesLP() (via
set_iommu_table_base_and_group). When we go to dlpar a multi-function
PCI device out:
We trip this BUG_ON, because there are still references on the table, so
it is not freed. Fix this by moving the powernv bus notifier to common
code and calling it for both powernv and pseries.
Anton has a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:
BUG_ON(td->cpu != smp_processor_id());
Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:
CPU: 0
Comm: watchdog/130
The problem is that we aren't ensuring the CPU active bit is set for the
secondary before allowing the master to continue on. The master unparks
the secondary CPU's kthreads and the scheduler looks for a CPU to run
on. It calls select_task_rq() and realises the suggested CPU is not in
the cpus_allowed mask. It then ends up in select_fallback_rq(), and
since the active bit isnt't set we choose some other CPU to run on.
This seems to have been introduced by 6acbfb96976f "sched: Fix hotplug
vs. set_cpus_allowed_ptr()", which changed from setting active before
online to setting active after online. However that was in turn fixing a
bug where other code assumed an active CPU was also online, so we can't
just revert that fix.
The simplest fix is just to spin waiting for both active & online to be
set. We already have a barrier prior to set_cpu_online() (which also
sets active), to ensure all other setup is completed before online &
active are set.
Fixes: 6acbfb96976f ("sched: Fix hotplug vs. set_cpus_allowed_ptr()") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
mc_saved_tmp is a static array allocated on the stack, we need to make
sure mc_saved_count stays within its bounds, otherwise we're overflowing
the stack in _save_mc(). A specially crafted microcode header could lead
to a kernel crash or potentially kernel execution.
Replacing a xattr consists of doing a lookup for its existing value, delete
the current value from the respective leaf, release the search path and then
finally insert the new value. This leaves a time window where readers (getxattr,
listxattrs) won't see any value for the xattr. Xattrs are used to store ACLs,
so this has security implications.
This change also fixes 2 other existing issues which were:
*) Deleting the old xattr value without verifying first if the new xattr will
fit in the existing leaf item (in case multiple xattrs are packed in the
same item due to name hash collision);
*) Returning -EEXIST when the flag XATTR_CREATE is given and the xattr doesn't
exist but we have have an existing item that packs muliple xattrs with
the same name hash as the input xattr. In this case we should return ENOSPC.
A test case for xfstests follows soon.
Thanks to Alexandre Oliva for reporting the non-atomicity of the xattr replace
implementation.
Reported-by: Alexandre Oliva <oliva@gnu.org> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
dst_orig should be released on error. Function like __xfrm_route_forward()
expects that behavior.
Since a recent commit, xfrm_lookup() may also be called by xfrm_lookup_route(),
which expects the opposite.
Let's introduce a new flag (XFRM_LOOKUP_KEEP_DST_REF) to tell what should be
done in case of error.
Fixes: f92ee61982d("xfrm: Generate blackhole routes only from route lookup functions") Signed-off-by: huaibin Wang <huaibin.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit 9cade1a46c77 (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <jerome.blin@intel.com> Fixes: 9cade1a46c77 (dma: dw: split driver to library part and platform code) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.
Fixes: c37791349cc7 ('IB/mlx4: Support PMA counters for IBoE') Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Current implementation doesn't zero out the pages allocated.
Honor the __GFP_ZERO flag and zero out if set.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[ luis: backported to 3.16: based on Suzuki's 3.14 backport ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com> Cc: Claudio Fleiner <cmf@daterainc.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Giridhar Malavali <giridhar.malavali@qlogic.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Slava Shwartsman <valyushash@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The error code paths that require cleanup use a goto to jump to the
cleanup code and return an error code. However, the error code variable
res, which is initialized to -EINVAL when declared, is then overwritten
with the return value of of_parse_phandle_with_args(), and reused as the
return code from of_irq_parse_one(). This leads to an undetermined error
being returned instead of the expected -EINVAL value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We should signal connect (pull up dp) after we have already
at peripheral mode, otherwise, the dp may be toggled due to
we reset controller or do disconnect during the initialization
for peripheral, then, the host may be confused during the
enumeration, eg, it finds the reset can't succeed, but the
device is still there, see below error message.
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: unable to enumerate USB device on port 1
Fixes: the issue existed when the otg fsm code was added. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A new uas compatible controller has shown up in some people's devices from
the manufacturer Initio Corporation, this controller needs the US_FL_NO_ATA_1X
quirk to work properly with uas, so add it to the uas quirks table.
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
As pointed by recent post[1] on exploiting DRAM physical imperfection,
/proc/PID/pagemap exposes sensitive information which can be used to do
attacks.
This disallows anybody without CAP_SYS_ADMIN to read the pagemap.
[ Eventually we might want to do anything more finegrained, but for now
this is the simple model. - Linus ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Seaborn <mseaborn@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit [ef403edb7558: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input. In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").
This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since moving the interface combination checks to mac80211, it's
broken because it now only considers interfaces with an assigned
channel context, so for example any interface that isn't active
can still be up, which is clearly an issue; also, in particular
P2P-Device wdevs are an issue since they never have a chanctx.
Fix this by counting running interfaces instead the ones with a
channel context assigned.
Fixes: 73de86a38962b ("cfg80211/mac80211: move interface counting for combination check to mac80211") Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[rewrite commit message, dig out the commit it fixes] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.
[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.293105] usb 1-1: can't set HNP mode: -32
[ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.466424] usb 1-1: can't set HNP mode: -32
[ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.636436] usb 1-1: can't set HNP mode: -32
[ 2.641003] usb usb1-port1: unable to enumerate USB device
Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Li Jun <b47624@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
As stated in kernel/cpu_pm.c, "Platform is responsible for ensuring
that cpu_pm_enter is not called twice on the same CPU before
cpu_pm_exit is called.". In the current code in case of failure when
calling mvebu_v7_cpu_suspend, the function cpu_pm_exit() is never
called whereas cpu_pm_enter() was called just before.
This patch moves the cpu_pm_exit() in order to balance the
cpu_pm_enter() calls.
drop_fpu() does clear_used_math() and usually this is correct
because tsk == current.
However switch_fpu_finish()->restore_fpu_checking() is called before
__switch_to() updates the "current_task" variable. If it fails,
we will wrongly clear the PF_USED_MATH flag of the previous task.
So use clear_stopped_child_used_math() instead.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Rik van Riel <riel@redhat.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Pekka Riikonen <priikone@iki.fi> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Suresh Siddha <sbsiddha@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20150309171041.GB11388@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
math_state_restore() assumes it is called with irqs disabled,
but this is not true if the caller is __restore_xstate_sig().
This means that if ia32_fxstate == T and __copy_from_user()
fails, __restore_xstate_sig() returns with irqs disabled too.
This triggers:
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:41
dump_stack
___might_sleep
? _raw_spin_unlock_irqrestore
__might_sleep
down_read
? _raw_spin_unlock_irqrestore
print_vma_addr
signal_fault
sys32_rt_sigreturn
Change __restore_xstate_sig() to call set_used_math()
unconditionally. This avoids enabling and disabling interrupts
in math_state_restore(). If copy_from_user() fails, we can
simply do fpu_finit() by hand.
[ Note: this is only the first step. math_state_restore() should
not check used_math(), it should set this flag. While
init_fpu() should simply die. ]
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Pekka Riikonen <priikone@iki.fi> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Rik van Riel <riel@redhat.com> Cc: Suresh Siddha <sbsiddha@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20150307153844.GB25954@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
devm_phy_create() stores the pointer to the new PHY at the address
returned by devres_alloc(). The res parameter passed to devm_phy_match()
is therefore the location where the pointer to the PHY is stored, hence
it needs to be dereferenced before comparing to the match data in order
to find the correct match.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The kernel crypto API logic requires the caller to provide the
length of (ciphertext || authentication tag) as cryptlen for the
AEAD decryption operation. Thus, the cipher implementation must
calculate the size of the plaintext output itself and cannot simply use
cryptlen.
The RFC4106 GCM decryption operation tries to overwrite cryptlen memory
in req->dst. As the destination buffer for decryption only needs to hold
the plaintext memory but cryptlen references the input buffer holding
(ciphertext || authentication tag), the assumption of the destination
buffer length in RFC4106 GCM operation leads to a too large size. This
patch simply uses the already calculated plaintext size.
In addition, this patch fixes the offset calculation of the AAD buffer
pointer: as mentioned before, cryptlen already includes the size of the
tag. Thus, the tag does not need to be added. With the addition, the AAD
will be written beyond the already allocated buffer.
Note, this fixes a kernel crash that can be triggered from user space
via AF_ALG(aead) -- simply use the libkcapi test application
from [1] and update it to use rfc4106-gcm-aes.
Using [1], the changes were tested using CAVS vectors to demonstrate
that the crypto operation still delivers the right results.
[1] http://www.chronox.de/libkcapi.html
CC: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fixes: d4332013919a ("driver core: dev_get_drvdata: Don't check for NULL dev") Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David Dueck <davidcdueck@googlemail.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The board id capability has been added in firmware 7.5.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The Fimware 8.1 has a bug in which the extra buttons are only sent when the
ExtBit is 1. This should be fixed in a future FW update which should have
a bump of the minor version.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On the X1 Carbon 3rd gen (with a 2015 broadwell cpu), the physical middle
button of the trackstick (attached to the touchpad serio device, of course)
seems to get lost.
Actually, the touchpads reports 3 extra buttons, which falls in the switch
below to the '2' case. Let's handle the case of odd numbers also, so that
the middle button finds its way back.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Post-2013 Lenovo laptops provide correct min/max dimensions, which are
different with the ones currently quirked. According to
https://bugzilla.kernel.org/show_bug.cgi?id=91541 the following board ids
are assigned in the post-2013 touchpads:
Using 2961 as the common minimum makes these 3 laptops OK. We may need
to update those values later if other pnp_ids has a lower board_id.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add a min/max range for board ids to the min/max coordinates quirk. This
makes it possible to restrict quirks to specific models based upon their
board id. The define ANY_BOARD_ID (0) serves as a wild card.
Signed-off-by: Daniel Martin <daniel.martin@secunet.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The firmware of the X240 (LEN0035, 2013/12) exposes the same values
x [1232..5710], y [1156..4696]
as the quirk applies.
Signed-off-by: Daniel Martin <consume.noise@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
re-order the tests to check SYN_CAP_MIN_DIMENSIONS even on FW 8.1 Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Logging the dimension values we queried and the values we use from a quirk
to overwrite can be helpful for debugging.
This partly relates to bug:
https://bugzilla.kernel.org/show_bug.cgi?id=91541
Signed-off-by: Daniel Martin <consume.noise@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Split the function synaptics_resolution() into synaptics_resolution() and
synaptics_quirks(). synaptics_resolution() will be called before
synaptics_quirks() to query dimensions and resolutions before overwriting
them with quirks.
Signed-off-by: Daniel Martin <consume.noise@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Normally _regulator_do_enable() isn't called on an already-enabled
rdev. That's because the main caller, _regulator_enable() always
calls _regulator_is_enabled() and only calls _regulator_do_enable() if
the rdev was not already enabled.
However, there is one caller of _regulator_do_enable() that doesn't
check: regulator_suspend_finish(). While we might want to make
regulator_suspend_finish() behave more like _regulator_enable(), it's
probably also a good idea to make _regulator_do_enable() robust if it
is called on an already enabled rdev.
At the moment, _regulator_do_enable() is _not_ robust for already
enabled rdevs if we're using an ena_pin. Each time
_regulator_do_enable() is called for an rdev using an ena_pin the
reference count of the ena_pin is incremented even if the rdev was
already enabled. This is not as intended because the ena_pin is for
something else: for keeping track of how many active rdevs there are
sharing the same ena_pin.
Here's how the reference counting works here:
* Each time _regulator_enable() is called we increment
rdev->use_count, so _regulator_enable() calls need to be balanced
with _regulator_disable() calls.
* There is no explicit reference counting in _regulator_do_enable()
which is normally just a warapper around rdev->desc->ops->enable()
with code for supporting delays. It's not expected that the
"ops->enable()" call do reference counting.
* Since regulator_ena_gpio_ctrl() does have reference counting
(handling the sharing of the pin amongst multiple rdevs), we
shouldn't call it if the current rdev is already enabled.
Note that as part of this we cleanup (remove) the initting of
ena_gpio_state in regulator_register(). In _regulator_do_enable(),
_regulator_do_disable() and _regulator_is_enabled() is is clear that
ena_gpio_state should be the state of whether this particular rdev has
requested the GPIO be enabled. regulator_register() was initting it
as the actual state of the pin.
Fixes: 967cfb18c0e3 ("regulator: core: manage enable GPIO list") Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The _regulator_do_enable() call ought to be a no-op when called on an
already-enabled regulator. However, as an optimization
_regulator_enable() doesn't call _regulator_do_enable() on an already
enabled regulator. That means we never test the case of calling
_regulator_do_enable() during normal usage and there may be hidden
bugs or warnings. We have seen warnings issued by the tps65090 driver
and bugs when using the GPIO enable pin.
Let's match the same optimization that _regulator_enable() in
regulator_suspend_finish(). That may speed up suspend/resume and also
avoids exposing hidden bugs.
[Use much clearer commit message from Doug Anderson]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When inserting a new register into a block at the lower end the present
bitmap is currently shifted into the wrong direction. The effect of this is
that the bitmap becomes corrupted and registers which are present might be
reported as not present and vice versa.
Fix this by shifting left rather than right.
Fixes: 472fdec7380c("regmap: rbtree: Reduce number of nodes, take 2") Reported-by: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The SGTL5000_CHIP_ANA_POWER register is cached. Update the cached
value instead of writing it directly.
Patch inspired by Russell King's more colorful remarks in this
patch:
https://github.com/SolidRun/linux-imx6-3.14/commit/dd4bf6a
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Because prior GCC versions always emitted NOPs on ALIGN directives, but
gcc5 started omitting them.
.LSTARTFDEDLSI1 says:
/* HACK: The dwarf2 unwind routines will subtract 1 from the
return address to get an address in the middle of the
presumed call instruction. Since we didn't get here via
a call, we need to include the nop before the real start
to make up for it. */
.long .LSTART_sigreturn-1-. /* PC-relative start address */
But commit 69d0627a7f6e ("x86 vDSO: reorder vdso32 code") from 2.6.25
replaced .org __kernel_vsyscall+32,0x90 by ALIGN right before
__kernel_sigreturn.
Of course, ALIGN need not generate any NOP in there. Esp. gcc5 collapses
vclock_gettime.o and int80.o together with no generated NOPs as "ALIGN".
So fix this by adding to that point at least a single NOP and make the
function ALIGN possibly with more NOPs then.
Kudos for reporting and diagnosing should go to Richard.
Reported-by: Richard Biener <rguenther@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1425543211-12542-1-git-send-email-jslaby@suse.cz Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The interrupt is enabled before the handler is set. Even this bug
did not appear, it is potentially dangerous as it can lead to a
NULL pointer dereference.
Fix the error by enabling the interrupt after
clockevents_config_and_register() is called.
Signed-off-by: Yongbae Park <yongbae2@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The initialisation of the efm32 clocksource first sets up the irq and only
after that initialises the data needed for irq handling. In case this
initialisation is delayed the irq handler would dereference a NULL pointer.
I'm not aware of anything that could delay the process in such a way, but it's
better to be safe than sorry, so setup the irq only when the clock event device
is ready.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Yongbae Park <yongbae2@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
when multiport is off, virtio console invokes config access from irq
context, config access is blocking on s390.
Fix this up by scheduling work from config irq - similar to what we do
for multiport configs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
when multiport is off, we don't initialize config work,
but we then cancel uninitialized control_work on freeze.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Routes without a control must use NULL for the control name. The sn95031
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc6f
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the sn95031 driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc6f ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Routes without a control must use NULL for the control name. The da732x
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc6f
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the da732x driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc6f ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Routes without a control must use NULL for the control name. The ak4671
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc6f
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the ak4671 driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc6f ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Some APs experience problems when working with
U-APSD. Decreasing the probability of that
happening by using legacy mode for all ACs but VO
isn't enough.
Cisco 4410N originally forced us to enable VO by
default only because it treated non-VO ACs as
legacy.
However some APs (notably Netgear R7000) silently
reclassify packets to different ACs. Since u-APSD
ACs require trigger frames for frame retrieval
clients would never see some frames (e.g. ARP
responses) or would fetch them accidentally after
a long time.
It makes little sense to enable u-APSD queues by
default because it needs userspace applications to
be aware of it to actually take advantage of the
possible additional powersavings. Implicitly
depending on driver autotrigger frame support
doesn't make much sense.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The mesh forwarding path was not checking that data
frames were protected when running an encrypted network;
add the necessary check.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This updates the bit sliced AES module to the latest version in the
upstream OpenSSL repository (e620e5ae37bc). This is needed to fix a
bug in the XTS decryption path, where data chunked in a certain way
could trigger the ciphertext stealing code, which is not supposed to
be active in the kernel build (The kernel implementation of XTS only
supports round multiples of the AES block size of 16 bytes, whereas
the conformant OpenSSL implementation of XTS supports inputs of
arbitrary size by applying ciphertext stealing). This is fixed in
the upstream version by adding the missing #ifndef XTS_CHAIN_TWEAK
around the offending instructions.
The upstream code also contains the change applied by Russell to
build the code unconditionally, i.e., even if __LINUX_ARM_ARCH__ < 7,
but implemented slightly differently.
Fixes: e4e7f10bfc40 ("ARM: add support for bit sliced AES using NEON instructions") Reported-by: Adrian Kotelba <adrian.kotelba@gmail.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Tested-by: Milan Broz <gmazyland@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since it's possible for the discard and write same queue limits to
change while the upper level command is being sliced and diced, fix up
both of them (a) to reject IO if the special command is unsupported at
the start of the function and (b) read the limits once and let the
commands error out on their own if the status happens to change.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The "dm snapshot: suspend origin when doing exception handover" commit
fixed a exception store handover bug associated with pending exceptions
to the "snapshot-origin" target.
However, a similar problem exists in snapshot merging. When snapshot
merging is in progress, we use the target "snapshot-merge" instead of
"snapshot-origin". Consequently, during exception store handover, we
must find the snapshot-merge target and suspend its associated
mapped_device.
To avoid lockdep warnings, the target must be suspended and resumed
without holding _origins_lock.
Introduce a dm_hold() function that grabs a reference on a
mapped_device, but unlike dm_get(), it doesn't crash if the device has
the DMF_FREEING flag set, it returns an error in this case.
In snapshot_resume() we grab the reference to the origin device using
dm_hold() while holding _origins_lock (_origins_lock guarantees that the
device won't disappear). Then we release _origins_lock, suspend the
device and grab _origins_lock again.
NOTE to stable@ people:
When backporting to kernels 3.18 and older, use dm_internal_suspend and
dm_internal_resume instead of dm_internal_suspend_fast and
dm_internal_resume_fast.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[ luis: backported to 3.16: as suggested by the author:
- replaced dm_internal_suspend_fast by dm_internal_suspend
- replaced dm_internal_resume_fast by dm_internal_resume ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In the function snapshot_resume we perform exception store handover. If
there is another active snapshot target, the exception store is moved
from this target to the target that is being resumed.
The problem is that if there is some pending exception, it will point to
an incorrect exception store after that handover, causing a crash due to
dm-snap-persistent.c:get_exception()'s BUG_ON.
This bug can be triggered by repeatedly changing snapshot permissions
with "lvchange -p r" and "lvchange -p rw" while there are writes on the
associated origin device.
To fix this bug, we must suspend the origin device when doing the
exception store handover to make sure that there are no pending
exceptions:
- introduce _origin_hash that keeps track of dm_origin structures.
- introduce functions __lookup_dm_origin, __insert_dm_origin and
__remove_dm_origin that manipulate the origin hash.
- modify snapshot_resume so that it calls dm_internal_suspend_fast() and
dm_internal_resume_fast() on the origin device.
NOTE to stable@ people:
When backporting to kernels 3.12-3.18, use dm_internal_suspend and
dm_internal_resume instead of dm_internal_suspend_fast and
dm_internal_resume_fast.
When backporting to kernels older than 3.12, you need to pick functions
dm_internal_suspend and dm_internal_resume from the commit fd2ed4d252701d3bbed4cd3e3d267ad469bb832a.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[ luis: backported to 3.16: as suggested by the author:
- replaced dm_internal_suspend_fast by dm_internal_suspend
- replaced dm_internal_resume_fast by dm_internal_resume ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It was always intended that a read to an unprovisioned block will return
zeroes regardless of whether the pool is in read-only or read-write
mode. thin_bio_map() was inconsistent with its handling of such reads
when the pool is in read-only mode, it now properly zero-fills the bios
it returns in response to unprovisioned block reads.
Eliminate thin_bio_map()'s special read-only mode handling of -ENODATA
and just allow the IO to be deferred to the worker which will result in
pool->process_bio() handling the IO (which already properly zero-fills
reads to unprovisioned blocks).
Reported-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
While working on sk_forward_alloc problems reported by Denys
Fedoryshchenko, we found that tcp connect() (and fastopen) do not call
sk_wmem_schedule() for SYN packet (and/or SYN/DATA packet), so
sk_forward_alloc is negative while connect is in progress.
We can fix this by calling regular sk_stream_alloc_skb() both for the
SYN packet (in tcp_connect()) and the syn_data packet in
tcp_send_syn_data()
Then, tcp_send_syn_data() can avoid copying syn_data as we simply
can manipulate syn_data->cb[] to remove SYN flag (and increment seq)
Instead of open coding memcpy_fromiovecend(), simply use this helper.
This leaves in socket write queue clean fast clone skbs.
This was tested against our fastopen packetdrill tests.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an
error) introduced the clamping of msg_namelen when the unsigned value
was larger than sizeof(struct sockaddr_storage). This caused a
msg_namelen of -1 to be valid. The native code was subsequently fixed by
commit dbb490b96584 (net: socket: error on a negative msg_namelen).
In addition, the native code sets msg_namelen to 0 when msg_name is
NULL. This was done in commit (6a2a2b3ae075 net:socket: set msg_namelen
to 0 if msg_name is passed as NULL in msghdr struct from userland) and
subsequently updated by 08adb7dabd48 (fold verify_iovec() into
copy_msghdr_from_user()).
This patch brings the get_compat_msghdr() in line with
copy_msghdr_from_user().
Fixes: db31c55a6fb2 (net: clamp ->msg_namelen instead of returning an error) Cc: David S. Miller <davem@davemloft.net> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: used davem's backport to 3.14 ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
tcp_send_fin() does not account for the memory it allocates properly, so
sk_forward_alloc can be negative in cases where we've sent a FIN:
ss example output (ss -amn | grep -B1 f4294):
tcp FIN-WAIT-1 0 1 192.168.0.1:45520 192.0.2.1:8080
skmem:(r0,rb87380,t0,tb87380,f4294966016,w1280,o0,bl0) Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
for throw routes to trigger evaluation of other policy rules
EAGAIN needs to be propagated up to fib_rules_lookup
similar to how its done for IPv4
A simple testcase for verification is:
ip -6 rule add lookup 33333 priority 33333
ip -6 route add throw 2001:db8::1
ip -6 route add 2001:db8::1 via fe80::1 dev wlan0 table 33333
ip route get 2001:db8::1
Signed-off-by: Steven Barth <cyrus@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
[I would really like an ACK on that one from dhowells; it appears to be
quite straightforward, but...]
MSG_PEEK isn't passed to ->recvmsg() via msg->msg_flags; as the matter of
fact, neither the kernel users of rxrpc, nor the syscalls ever set that bit
in there. It gets passed via flags; in fact, another such check in the same
function is done correctly - as flags & MSG_PEEK.
It had been that way (effectively disabled) for 8 years, though, so the patch
needs beating up - that case had never been tested. If it is correct, it's
-stable fodder.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It should be checking flags, not msg->msg_flags. It's ->sendmsg()
instances that need to look for that in ->msg_flags, ->recvmsg() ones
(including the other ->recvmsg() instance in that file, as well as
unix_dgram_recvmsg() this one claims to be imitating) check in flags.
Braino had been introduced in commit dcda13 ("caif: Bugfix - use MSG_TRUNC
in receive") back in 2010, so it goes quite a while back.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
inet_diag_dump_one_icsk() allocates too small skb.
Add inet_sk_attr_size() helper right before inet_sk_diag_fill()
so that it can be updated if/when new attributes are added.
iproute2/ss currently does not use this dump_one() interface,
this might explain nobody noticed this problem yet.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The rds_iw_update_cm_id function stores a large 'struct rds_sock' object
on the stack in order to pass a pair of addresses. This happens to just
fit withint the 1024 byte stack size warning limit on x86, but just
exceed that limit on ARM, which gives us this warning:
net/rds/iw_rdma.c:200:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
As the use of this large variable is basically bogus, we can rearrange
the code to not do that. Instead of passing an rds socket into
rds_iw_get_device, we now just pass the two addresses that we have
available in rds_iw_update_cm_id, and we change rds_iw_get_mr accordingly,
to create two address structures on the stack there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
sysctl has sysctl.net.core.rmem_*/wmem_* parameters which can be
set to incorrect values. Given that 'struct sk_buff' allocates from
rcvbuf, incorrectly set buffer length could result to memory
allocation failures. For example, set them as follows:
Moreover, the possible minimum is 1, so we can get another kernel panic:
...
BUG: unable to handle kernel paging request at ffff88013caee5c0
IP: [<ffffffff815604cf>] __alloc_skb+0x12f/0x1f0
...
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Firstly, handle zero length calls properly. Believe it or not there
are a few of these happening during early boot.
Next, we can't just drop to a memcpy() call in the forward copy case
where dst <= src. The reason is that the cache initializing stores
used in the Niagara memcpy() implementations can end up clearing out
cache lines before we've sourced their original contents completely.
For example, considering NG4memcpy, the main unrolled loop begins like
this:
Assume dst is 64 byte aligned and let's say that dst is src - 8 for
this memcpy() call. That store at the end there is the one to the
first line in the cache line, thus clearing the whole line, which thus
clobbers "src + 0x28" before it even gets loaded.
To avoid this, just fall through to a simple copy only mildly
optimized for the case where src and dst are 8 byte aligned and the
length is a multiple of 8 as well. We could get fancy and call
GENmemcpy() but this is good enough for how this thing is actually
used.
Reported-by: David Ahern <david.ahern@oracle.com> Reported-by: Bob Picco <bpicco@meloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
With the increase in number of CPUs calls to functions that dump
output to console (e.g., arch_trigger_all_cpu_backtrace) can take
a long time to complete. If IRQs are disabled eventually the NMI
watchdog kicks in and creates more havoc. Avoid by telling the NMI
watchdog everything is ok.
Signed-off-by: David Ahern <david.ahern@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The reason is that state is never reset (stays with PERF_HES_UPTODATE set).
Add a call to sparc_pmu_enable_event during the added_event handling.
Clean up the encoding since pmu_start calls sparc_pmu_enable_event which
does the same. Passing PERF_EF_RELOAD to sparc_pmu_start means the call
to sparc_perf_event_set_period can be removed as well.
With this patch:
$ perf stat ls
...
Performance counter stats for 'ls':
Signed-off-by: David Ahern <david.ahern@oracle.com> Acked-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
