In order to measure the boot process, the timer should be switched on as
early in boot as possible. As well, the commit defines the get_cycles
macro, like the previous patches in this series, so that generic code is
aware that it's implemented by the platform, as is done on other archs.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jonas Bonn <jonas@southpole.se> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Acked-by: Stafford Horne <shorne@gmail.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the driver support subdev mode, the parameter "dev->pm.dev" will be
NULL in mtk_vcodec_dec_remove. Kernel will crash when try to rmmod
mtk-vcodec-dec.ko.
For correctness, we need to configure the packet filters for timestamping
during bnxt_open. This way they are always configured after firmware
reset or chip reset. We should not assume that the filters will always
be retained across resets.
This patch modifies the ioctl handler and always configures the PTP
filters in the bnxt_open() path.
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCA controllers since
they answer HCI_OP_READ_DEF_ERR_DATA_REPORTING with error code
"UNKNOWN HCI COMMAND" as shown below:
This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be
used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even
if its support command bit are set since some controller report it as
supported but the command don't work properly with some configurations
(e.g. BT_VOICE_TRANSPARENT/mSBC).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit made binding and unbinding of USB Ethernet asymmetrical:
Before, usbnet_probe() first invoked the ->bind() callback and then
register_netdev(). usbnet_disconnect() mirrored that by first invoking
unregister_netdev() and then ->unbind().
Since the commit, the order in usbnet_disconnect() is reversed and no
longer mirrors usbnet_probe().
One consequence is that a PHY disconnected (and stopped) in ->unbind()
is afterwards stopped once more by unregister_netdev() as it closes the
netdev before unregistering. That necessitates a contortion in ->stop()
because the PHY may only be stopped if it hasn't already been
disconnected.
Reverting the commit allows making the call to phy_stop() unconditional
in ->stop().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500 Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514 Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Oliver Neukum <oneukum@suse.com> Cc: Martyn Welch <martyn.welch@collabora.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an adapter is trying to claim a free logical address then it is
in the 'is_configuring' state. If during that process the cable is
disconnected (HPD goes low, which in turn invalidates the physical
address), then cec_adap_unconfigure() is called, and that set the
is_configuring boolean to false, even though the thread that's
trying to claim an LA is still running.
Don't touch the is_configuring bool in cec_adap_unconfigure(), it
will eventually be cleared by the thread. By making that change
the cec_config_log_addr() function also had to change: it was
aborting if is_configuring became false (since that is what
cec_adap_unconfigure() did), but that no longer works. Instead
check if the physical address is invalid. That is a much
more appropriate check anyway.
This fixes a bug where the the adapter could be disabled even
though the device was still configuring. This could cause POLL
transmits to time out.
Since usb_register_dev() from imon_init_display() from imon_probe() holds
minor_rwsem while display_open() which holds driver_lock and ictx->lock is
called with minor_rwsem held from usb_open(), holding driver_lock or
ictx->lock when calling usb_register_dev() causes circular locking
dependency problem.
Since usb_deregister_dev() from imon_disconnect() holds minor_rwsem while
display_open() which holds driver_lock is called with minor_rwsem held,
holding driver_lock when calling usb_deregister_dev() also causes circular
locking dependency problem.
Sean Young explained that the problem is there are imon devices which have
two usb interfaces, even though it is one device. The probe and disconnect
function of both usb interfaces can run concurrently.
Alan Stern responded that the driver and USB cores guarantee that when an
interface is probed, both the interface and its USB device are locked.
Ditto for when the disconnect callback gets run. So concurrent probing/
disconnection of multiple interfaces on the same device is not possible.
Therefore, we don't need locks for handling race between imon_probe() and
imon_disconnect(). But we still need to handle race between display_open()
/vfd_write()/lcd_write()/display_close() and imon_disconnect(), for
disconnect event can happen while file descriptors are in use.
Since "struct file"->private_data is set by display_open(), vfd_write()/
lcd_write()/display_close() can assume that "struct file"->private_data
is not NULL even after usb_set_intfdata(interface, NULL) was called.
Replace insufficiently held driver_lock with refcount_t based management.
Add a boolean flag for recording whether imon_disconnect() was already
called. Use RCU for accessing this boolean flag and refcount_t.
Since the boolean flag for imon_disconnect() is shared, disconnect event
on either intf0 or intf1 affects both interfaces. But I assume that this
change does not matter, for usually disconnect event would not happen
while interfaces are in use.
Link: https://syzkaller.appspot.com/bug?extid=c558267ad910fc494497 Reported-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Tested-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Always set pps_cb_qp_offset and pps_cr_qp_offset values in Hantro/G2
register whatever is V4L2_HEVC_PPS_FLAG_PPS_SLICE_CHROMA_QP_OFFSETS_PRESENT
flag value.
The vendor code does the same to set these values.
This fixes conformance test CAINIT_G_SHARP_3.
Fluster HEVC score is increase by one with this patch.
Let VIDIOC_ENUM_FRAMEINTERVALS return -EINVAL if userspace queries
frame intervals for frame sizes unsupported by the encoder. Fixes the
following v4l2-compliance failure:
fail: v4l2-test-formats.cpp(123): found frame intervals for invalid size 47x16
fail: v4l2-test-formats.cpp(282): node->codec_mask & STATEFUL_ENCODER
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
[hverkuil: drop incorrect 'For decoder devices, return -ENOTTY.' in the commit log]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver needs to check if the format is 802.2 vs 802.3 in order to set
a tx descriptor flag. skb->protocol can't be used, since it may not be properly
initialized for packets coming in from a packet socket.
Fix misdetection by checking the ethertype from the skb data instead
When filtering what tests to run (suites and/or cases) via
kunit.filter_glob (e.g. kunit.py run <glob>), we allocate copies of
suites.
These allocations can fail, and we largely don't handle that.
Note: realistically, this probably doesn't matter much.
We're not allocating much memory and this happens early in boot, so if
we can't do that, then there's likely far bigger problems.
This patch makes us immediately bail out from the top-level function
(kunit_filter_suites) with -ENOMEM if any of the underlying kmalloc()
calls return NULL.
Implementation note: we used to return NULL pointers from some functions
to indicate either that all suites/tests were filtered out or there was
an error allocating the new array.
We'll log a short error in this case and not run any tests or print a
TAP header. From a kunit.py user's perspective, they'll get a message
about missing/invalid TAP output and have to dig into the test.log to
see it. Since hitting this error seems so unlikely, it's probably fine
to not invent a way to plumb this error message more visibly.
See also: https://lore.kernel.org/linux-kselftest/20220329103919.2376818-1-lv.ruyi@zte.com.cn/
There was a "type" element added to this structure, but some static
values were missed. The default value will be zero, which is correct,
but create an initializer for the type and initialize the type properly
in the initializer to avoid future issues.
Even though it's not possible to get into the SSIF_GETTING_MESSAGES and
SSIF_GETTING_EVENTS states without a valid message in the msg field,
it's probably best to be defensive here and check and print a log, since
that means something else went wrong.
Also add a default clause to that switch statement to release the lock
and print a log, in case the state variable gets messed up somehow.
ASUS B1400CEAE fails to resume from suspend to idle by default. This was
bisected back to commit df4f9bc4fb9c ("nvme-pci: add support for ACPI
StorageD3Enable property") but this is a red herring to the problem.
Before this commit the system wasn't getting into deepest sleep state.
Presumably this commit is allowing entry into deepest sleep state as
advertised by firmware, but there are some other problems related to
the wakeup.
As it is confirmed the system works properly with S3, set the default for
this system to S3.
Reported-by: Jian-Hong Pan <jhp@endlessos.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215742 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Jian-Hong Pan <jhp@endlessos.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hold writers when changing a mount's idmapping to make it more robust.
The vfs layer takes care to retrieve the idmapping of a mount once
ensuring that the idmapping used for vfs permission checking is
identical to the idmapping passed down to the filesystem.
For ioctl codepaths the filesystem itself is responsible for taking the
idmapping into account if they need to. While all filesystems with
FS_ALLOW_IDMAP raised take the same precautions as the vfs we should
enforce it explicitly by making sure there are no active writers on the
relevant mount while changing the idmapping.
This is similar to turning a mount ro with the difference that in
contrast to turning a mount ro changing the idmapping can only ever be
done once while a mount can transition between ro and rw as much as it
wants.
This is a minor user-visible change. But it is extremely unlikely to
matter. The caller must've created a detached mount via OPEN_TREE_CLONE
and then handed that O_PATH fd to another process or thread which then
must've gotten a writable fd for that mount and started creating files
in there while the caller is still changing mount properties. While not
impossible it will be an extremely rare corner-case and should in
general be considered a bug in the application. Consider making a mount
MOUNT_ATTR_NOEXEC or MOUNT_ATTR_NODEV while allowing someone else to
perform lookups or exec'ing in parallel by handing them a copy of the
OPEN_TREE_CLONE fd or another fd beneath that mount.
Link: https://lore.kernel.org/r/20220510095840.152264-1-brauner@kernel.org Cc: Seth Forshee <seth.forshee@digitalocean.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We observed the error "cacheline tracking ENOMEM, dma-debug disabled"
during a light system load (copying some files). The reason for this error
is that the dma_active_cacheline radix tree uses GFP_NOWAIT allocation -
so it can't access the emergency memory reserves and it fails as soon as
anybody reaches the watermark.
This patch changes GFP_NOWAIT to GFP_ATOMIC, so that it can access the
emergency memory reserves.
When we use raw_spin_rq_lock() to acquire the rq lock and have to
update the rq clock while holding the lock, the kernel may issue
a WARN_DOUBLE_CLOCK warning.
Since we directly use raw_spin_rq_lock() to acquire rq lock instead of
rq_lock(), there is no corresponding change to rq->clock_update_flags.
In particular, we have obtained the rq lock of other CPUs, the
rq->clock_update_flags of this CPU may be RQCF_UPDATED at this time, and
then calling update_rq_clock() will trigger the WARN_DOUBLE_CLOCK warning.
So we need to clear RQCF_UPDATED of rq->clock_update_flags to avoid
the WARN_DOUBLE_CLOCK warning.
For the sched_rt_period_timer() and migrate_task_rq_dl() cases
we simply replace raw_spin_rq_lock()/raw_spin_rq_unlock() with
rq_lock()/rq_unlock().
For the {pull,push}_{rt,dl}_task() cases, we add the
double_rq_clock_clear_update() function to clear RQCF_UPDATED of
rq->clock_update_flags, and call double_rq_clock_clear_update()
before double_lock_balance()/double_rq_lock() returns to avoid the
WARN_DOUBLE_CLOCK warning.
Steps to reproduce:
1. Enable CONFIG_SCHED_DEBUG when compiling the kernel
2. echo 1 > /sys/kernel/debug/clear_warn_once
echo "WARN_DOUBLE_CLOCK" > /sys/kernel/debug/sched/features
echo "NO_RT_PUSH_IPI" > /sys/kernel/debug/sched/features
3. Run some rt/dl tasks that periodically work and sleep, e.g.
Create 2*n rt or dl (90% running) tasks via rt-app (on a system
with n CPUs), and Dietmar Eggemann reports Call Trace 4 when running
on PREEMPT_RT kernel.
gcc 12 does not (always) optimize away code that should only be generated
if parameters are constant and within in a certain range. This depends on
various obscure kernel config options, however in particular
PROFILE_ALL_BRANCHES can trigger this compile error:
In function ‘__atomic_add_const’,
inlined from ‘__preempt_count_add.part.0’ at ./arch/s390/include/asm/preempt.h:50:3:
./arch/s390/include/asm/atomic_ops.h:80:9: error: impossible constraint in ‘asm’
80 | asm volatile( \
| ^~~
Workaround this by simply disabling the optimization for
PROFILE_ALL_BRANCHES, since the kernel will be so slow, that this
optimization won't matter at all.
Reported-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I have a syzbot report that managed to get a crash in skb_checksum_help()
If syzbot can trigger these BUG(), it makes sense to replace
them with more friendly WARN_ON_ONCE() since skb_checksum_help()
can instead return an error code.
Note that syzbot will still crash there, until real bug is fixed.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When configuring CMF management based on signals instead of FPINs, FPIN
alarm and warning statistics are not tracked.
Change the behavior so that FPIN alarms and warnings are always tracked
regardless of the configured mode.
Similar changes are made in the CMF signal stat accounting logic. Upon
receipt of a signal, only track signaled alarms and warnings. FPIN stats
should not be incremented upon receipt of a signal.
Link: https://lore.kernel.org/r/20220506035519.50908-11-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After running a short external loopback test, when the external loopback is
removed and a normal cable inserted that is directly connected to a target
device, the system oops in the llpfc_set_rrq_active() routine.
When the loopback was inserted an FLOGI was transmit. As we're looped back,
we receive the FLOGI request. The FLOGI is ABTS'd as we recognize the same
wppn thus understand it's a loopback. However, as the ABTS sends address
information the port is not set to (fffffe), the ABTS is dropped on the
wire. A short 1 frame loopback test is run and completes before the ABTS
times out. The looback is unplugged and the new cable plugged in, and the
an FLOGI to the new device occurs and completes. Due to a mixup in ref
counting the completion of the new FLOGI releases the fabric ndlp. Then the
original ABTS completes and references the released ndlp generating the
oops.
Correct by no-op'ing the ABTS when in loopback mode (it will be dropped
anyway). Added a flag to track the mode to recognize when it should be
no-op'd.
Link: https://lore.kernel.org/r/20220506035519.50908-5-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SOF topology supports 2 BE Links(dmic01 and dmic16k) and each
link supports up to four DMICs. However, Chromebook does not implement
ACPI NHLT table so the mach->mach_params.dmic_num is always zero. We
add a quirk so machine driver knows it's running on a Chromebook and
need to create BE Links for DMIC.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Brent Lu <brent.lu@intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220509170922.54868-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, health recovery will reload driver to recover it from fatal
errors. During the driver's load process, it would wait for FW to set the
pre-init bit for up to 120 seconds, beyond this threshold it would abort
the load process. In some cases, such as a FW upgrade on the DPU, this
timeout period is insufficient, and the user has no way to recover the
host device.
To solve this issue, introduce a new FW pre-init timeout for health
recovery, which is set to 2 hours.
The timeout for devlink reload and probe will use the original one because
they are user triggered flows, and therefore should not have a
significantly long timeout, during which the user command would hang.
The endianness flag is used on the CODEC side to specify an
ambivalence to endian, typically because it is lost over the hardware
link. This device receives audio over an I2S DAI and as such should
have endianness applied.
A fixup is also required to use the width directly rather than relying
on the format in hw_params, now both little and big endian would be
supported. It is worth noting this changes the behaviour of S24_LE to
use a word length of 24 rather than 32. This would appear to be a
correction since the fact S24_LE is stored as 32 bits should not be
presented over the bus.
When "crashkernel=X,high" is used, there may be two crash regions:
high=crashk_res and low=crashk_low_res. But now the syscall
kexec_file_load() only add crashk_res into "linux,usable-memory-range",
this may cause the second kernel to have no available dma memory.
Fix it like kexec-tools does for option -c, add both 'high' and 'low'
regions into the dtb.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Baoquan He <bhe@redhat.com> Link: https://lore.kernel.org/r/20220506114402.365-6-thunder.leizhen@huawei.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When mapping the DMA-BUF attachment fails, map->sgt will be an ERR_PTR-
encoded error code and the cleanup code would try to free that memory,
which obviously would fail.
Zero out that pointer after extracting the error code when this happens
so that kfree() can do the right thing.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a slab-out-of-bounds Write bug in hid-bigbenff driver.
The problem is the driver assumes the device must have an input but
some malicious devices violate this assumption.
Fix this by checking hid_device's input is non-empty before its usage.
The ice_get_vf_vsi function can return NULL in some cases, such as if
handling messages during a reset where the VSI is being removed and
recreated.
Several places throughout the driver do not bother to check whether this
VSI pointer is valid. Static analysis tools maybe report issues because
they detect paths where a potentially NULL pointer could be dereferenced.
Fix this by checking the return value of ice_get_vf_vsi everywhere.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MT6315 PMIC dt-binding should enforce that one of the valid
regulator-compatible is set in each regulator node. However it was
mistakenly matching against regulator-name instead.
Fix the typo. This not only fixes the compatible verification, but also
lifts the regulator-name restriction, so that more meaningful names can
be set for each platform.
When psp_hw_init failed, it will set the load_type to AMDGPU_FW_LOAD_DIRECT.
During amdgpu_device_ip_fini, amdgpu_ucode_free_bo checks that load_type is
AMDGPU_FW_LOAD_DIRECT and skips deallocating fw_buf causing memory leak.
Remove load_type check in amdgpu_ucode_free_bo.
Signed-off-by: Alice Wong <shiwei.wong@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocations should be done in sw_init. hw_init should
just be hardware programming needed to initialize the IP block.
This is how most other IP blocks work. Move the GPU memory
allocations from psp hw_init to psp sw_init and move the memory
free to sw_fini. This also fixes a potential GPU memory leak
if psp hw_init fails.
When trapping packets for on-CPU processing, Spectrum machines
differentiate between control and non-control traps. Traffic trapped
through non-control traps is treated as data and kept in shared buffer in
pools 0-4. Traffic trapped through control traps is kept in the dedicated
control buffer 9. The advantage of marking traps as control is that
pressure in the data plane does not prevent the control traffic to be
processed.
When the LLDP trap was introduced, it was marked as a control trap. But
then in commit aed4b5721143 ("mlxsw: spectrum: PTP: Hook into packet
receive path"), PTP traps were introduced. Because Ethernet-encapsulated
PTP packets look to the Spectrum-1 ASIC as LLDP traffic and are trapped
under the LLDP trap, this trap was reconfigured as non-control, in sync
with the PTP traps.
There is however no requirement that PTP traffic be handled as data.
Besides, the usual encapsulation for PTP traffic is UDP, not bare Ethernet,
and that is in deployments that even need PTP, which is far less common
than LLDP. This is reflected by the default policer, which was not bumped
up to the 19Kpps / 24Kpps that is the expected load of a PTP-enabled
Spectrum-1 switch.
Marking of LLDP trap as non-control was therefore probably misguided. In
this patch, change it back to control.
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The idea behind the warnings is that the user would get warned in case when
more than one priority is configured for a given DSCP value on a netdevice.
The warning is currently wrong, because dcb_ieee_getapp_mask() returns
the first matching entry, not all of them, and the warning will then claim
that some priority is "current", when in fact it is not.
But more importantly, the warning is misleading in general. Consider the
following commands:
# dcb app flush dev swp19 dscp-prio
# dcb app add dev swp19 dscp-prio 24:3
# dcb app replace dev swp19 dscp-prio 24:2
The last command will issue the following warning:
mlxsw_spectrum3 0000:07:00.0 swp19: Ignoring new priority 2 for DSCP 24 in favor of current value of 3
The reason is that the "replace" command works by first adding the new
value, and then removing all old values. This is the only way to make the
replacement without causing the traffic to be prioritized to whatever the
chip defaults to. The warning is issued in response to adding the new
priority, and then no warning is shown when the old priority is removed.
The upshot is that the canonical way to change traffic prioritization
always produces a warning about ignoring the new priority, but what gets
configured is in fact what the user intended.
An option to just emit warning every time that the prioritization changes
just to make it clear that it happened is obviously unsatisfactory.
Therefore, in this patch, remove the warnings.
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible to craft a topology where sof_get_control_data() would do
out of bounds access because it expects that it is only called when the
payload is bytes type.
Confusingly it also handles other types of controls, but the payload
parsing implementation is only valid for bytes.
Fix the code to count the non bytes controls and instead of storing a
pointer to sof_abi_hdr in sof_widget_data (which is only valid for bytes),
store the pointer to the data itself and add a new member to save the size
of the data.
In case of non bytes controls we store the pointer to the chanv itself,
which is just an array of values at the end.
In case of bytes control, drop the wrong cdata->data (wdata[i].pdata) check
against NULL since it is incorrect and invalid in this context.
The data is pointing to the end of cdata struct, so it should never be
null.
Reported-by: Sergey Senozhatsky <senozhatsky@chromium.org> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Tested-by: Sergey Senozhatsky <senozhatsky@chromium.org> Link: https://lore.kernel.org/r/20220427185221.28928-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DAPM tracks and reports the value presented to the user from DAPM controls
separately to the register value, these may diverge during initialisation
or when an autodisable control is in use.
When writing DAPM controls we currently report that a change has occurred
if either the DAPM value or the value stored in the register has changed,
meaning that if the two are out of sync we may appear to report a spurious
event to userspace. Since we use this folded in value for nothing other
than the value reported to userspace simply drop the folding in of the
register change.
When an FTE has no children is means all the rules where removed
and the FTE can be deleted regardless of the dests_size value.
While dests_size should be 0 when there are no children
be extra careful not to leak memory or get firmware syndrome
if the proper bookkeeping of dests_size wasn't done.
Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When tcmu_vma_fault() gets a page successfully, before the current context
completes page fault procedure, find_free_blocks() may run and call
unmap_mapping_range() to unmap the page. Assume that when
find_free_blocks() initially completes and the previous page fault
procedure starts to run again and completes, then one truncated page has
been mapped to userspace. But note that tcmu_vma_fault() has gotten a
refcount for the page so any other subsystem won't be able to use the page
unless the userspace address is unmapped later.
If another command subsequently runs and needs to extend dbi_thresh it may
reuse the corresponding slot for the previous page in data_bitmap. Then
though we'll allocate new page for this slot in data_area, no page fault
will happen because we have a valid map and the real request's data will be
lost.
Filesystem implementations will also run into this issue but they usually
lock the page when vm_operations_struct->fault gets a page and unlock the
page after finish_fault() completes. For truncate filesystems lock pages in
truncate_inode_pages() to protect against racing wrt. page faults.
To fix this possible data corruption scenario we can apply a method similar
to the filesystems. For pages that are to be freed, tcmu_blocks_release()
locks and unlocks. Make tcmu_vma_fault() also lock found page under
cmdr_lock. At the same time, since tcmu_vma_fault() gets an extra page
refcount, tcmu_blocks_release() won't free pages if pages are in page fault
procedure, which means it is safe to call tcmu_blocks_release() before
unmap_mapping_range().
With these changes tcmu_blocks_release() will wait for all page faults to
be completed before calling unmap_mapping_range(). And later, if
unmap_mapping_range() is called, it will ensure stale mappings are removed.
When test connect/disconnect to an AP frequently with WCN6855, sometimes
it show below log.
[ 277.040121] wls1: deauthenticating from 8c:21:0a:b3:5a:64 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 277.050906] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050944] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050954] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050961] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.050967] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 277.050976] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050983] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050989] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050995] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.051000] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 278.064050] ath11k_pci 0000:05:00.0: failed to request fw stats: -110
Reason is:
When running disconnect operation, sta_info removed from local->sta_hash
by __sta_info_destroy_part1() from __sta_info_flush(), after this,
ieee80211_find_sta_by_ifaddr() which called by
ath11k_wmi_tlv_fw_stats_data_parse() and ath11k_wmi_tlv_rssi_chain_parse()
cannot find this station, then failed log printed.
steps are like this:
1. when disconnect from AP, __sta_info_destroy() called __sta_info_destroy_part1()
and __sta_info_destroy_part2().
2. in __sta_info_destroy_part1(), it has "sta_info_hash_del(local, sta)"
and "list_del_rcu(&sta->list)", it will remove the ieee80211_sta from the
list of ieee80211_hw.
3. in __sta_info_destroy_part2(), it called drv_sta_state()->ath11k_mac_op_sta_state(),
then peer->sta is clear at this moment.
4. in __sta_info_destroy_part2(), it then called sta_set_sinfo()->drv_sta_statistics()
->ath11k_mac_op_sta_statistics(), then WMI_REQUEST_STATS_CMDID sent to firmware.
5. WMI_UPDATE_STATS_EVENTID reported from firmware, at this moment, the
ieee80211_sta can not be found again because it has remove from list in
step2 and also peer->sta is clear in step3.
6. in __sta_info_destroy_part2(), it then called cleanup_single_sta()->
sta_info_free()->kfree(sta), at this moment, the ieee80211_sta is freed
in memory, then the failed log will not happen because function
ath11k_mac_op_sta_state() will not be called.
Actually this print log is not a real error, it is only to skip parse the
info, so change to skip print by default debug setting.
Context tracking call must be done after hardirq tracking call,
otherwise lockdep_assert_irqs_disabled called from rcu_eqs_exit gives
a warning. To avoid context tracking logic duplication for IRQ/exception
entry paths move trace_hardirqs_off call back to common entry code.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, dpu_hw_lm_collect_misr returns EINVAL if CRC is disabled.
This causes a lot of spam in the DRM debug logs as it's called for every
vblank.
Instead of returning EINVAL when CRC is disabled in
dpu_hw_lm_collect_misr, let's return ENODATA and add an extra ENODATA check
before the debug log in dpu_crtc_get_crc.
Changes since V1:
- Added reported-by and suggested-by tags
If a compat process tries to execute an unknown system call above the
__ARM_NR_COMPAT_END number, the kernel sends a SIGILL signal to the
offending process. Information about the error is printed to dmesg in
compat_arm_syscall() -> arm64_notify_die() -> arm64_force_sig_fault() ->
arm64_show_signal().
arm64_show_signal() interprets a non-zero value for
current->thread.fault_code as an exception syndrome and displays the
message associated with the ESR_ELx.EC field (bits 31:26).
current->thread.fault_code is set in compat_arm_syscall() ->
arm64_notify_die() with the bad syscall number instead of a valid ESR_ELx
value. This means that the ESR_ELx.EC field has the value that the user set
for the syscall number and the kernel can end up printing bogus exception
messages*. For example, for the syscall number 0x68000000, which evaluates
to ESR_ELx.EC value of 0x1A (ESR_ELx_EC_FPAC) the kernel prints this error:
which is misleading, as the bad compat syscall has nothing to do with
pointer authentication.
Stop arm64_show_signal() from printing exception syndrome information by
having compat_arm_syscall() set the ESR_ELx value to 0, as it has no
meaning for an invalid system call number. The example above now becomes:
which although shows less information because the syscall number,
wrongfully advertised as the ESR value, is missing, it is better than
showing plainly wrong information. The syscall number can be easily
obtained with strace.
*A 32-bit value above or equal to 0x8000_0000 is interpreted as a negative
integer in compat_arm_syscal() and the condition scno < __ARM_NR_COMPAT_END
evaluates to true; the syscall will exit to userspace in this case with the
ENOSYS error code instead of arm64_notify_die() being called.
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Reported-by: kernel test robot <lkp@intel.com> CC: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes the deadlock warning by ensuring pm.mutex is not
held while holding the topology lock. For this, kfd_local_mem_info
is moved into the KFD dev struct and filled during device init.
This cached value can then be used instead of querying the value
again and again.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the check for format_count > 64 in __drm_universal_plane_init()
shouldn't be hit (it's a WARN_ON), in its current position it will then
leak the plane->format_types array and fail to call
drm_mode_object_unregister() leaking the modeset identifier. Move it to
the start of the function to avoid allocating those resources in the
first place.
Add a quirk for the HP Pro Tablet 408, this BYTCR tablet has no CHAN
package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which
is the default for BYTCR devices.
It also uses DMIC1 for the internal mic rather then the default IN3
and it uses JD2 rather then the default JD1 for jack-detect.
If no handler is found in lpfc_complete_unsol_iocb() to match the rctl of a
received frame, the frame is dropped and resources are leaked.
Fix by returning resources when discarding an unhandled frame type. Update
lpfc_fc_frame_check() handling of NOP basic link service.
Link: https://lore.kernel.org/r/20220426181419.9154-1-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync() and
pm_runtime_put_noidle(). This change is just to simplify the code, no
actual functional changes.
This patch fixes the issue where the driver miscomputes the 64-bit
values of the wptr of the SDMA doorbell when initializing the
hardware. SDMA engines v4 and later on have full 64-bit registers for
wptr thus they should be set properly.
Older generation hardwares like CIK / SI have only 16 / 20 / 24bits
for the WPTR, where the calls of lower_32_bits() will be removed in a
following patch.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Haohui Mai <ricetons@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If major equals 0, register_chrdev() returns an error code when it fails.
This function dynamically allocates a major and returns its number on
success, so we should use "< 0" to check it instead of "!".
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning. Similar to the issue pointed
out in sdhci-of-arasan.c driver, commit 3794c542641f ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Do what is done in other DMA-enabled MMC host drivers (cf. host/mmci.c) and
limit the maximum segment size based on the DMA engine's capabilities. This
is needed to avoid warnings like the following with CONFIG_DMA_API_DEBUG=y.
If bitmap area contains invalid data, kernel will crash then mdadm
triggers "Segmentation fault".
This is cluster-md speical bug. In non-clustered env, mdadm will
handle broken metadata case. In clustered array, only kernel space
handles bitmap slot info. But even this bug only happened in clustered
env, current sanity check is wrong, the code should be changed.
In md_bitmap_read_sb (called by md_bitmap_create), bad bitmap magic didn't
block chunksize assignment, and zero value made DIV_ROUND_UP_SECTOR_T()
trigger "divide error".
When the driver fails to call the dma_set_mask(), the driver will get
the following splat:
[ 55.853884] BUG: KASAN: use-after-free in __process_removed_driver+0x3c/0x240
[ 55.854486] Read of size 8 at addr ffff88810de60408 by task modprobe/590
[ 55.856822] Call Trace:
[ 55.860327] __process_removed_driver+0x3c/0x240
[ 55.861347] bus_for_each_dev+0x102/0x160
[ 55.861681] i2c_del_driver+0x2f/0x50
This is because the driver has initialized the i2c related resources
in cx23885_dev_setup() but not released them in error handling, fix this
bug by modifying the error path that jumps after failing to call the
dma_set_mask().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During reconfig (DRC) event from firmware, it is not guaranteed that
all the DPB(internal) buffers would be released by the firmware. Some
buffers might be released gradually while processing frames from the
new sequence. These buffers now stay idle in the dpblist.
In subsequent call to queue the DPBs to firmware, these idle buffers
should not be queued. The fix identifies those buffers and free them.
If venus_probe fails at pm_runtime_put_sync the error handling first
calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets
core->ops to NULL, hfi_core_deinit cannot call the core_deinit function
anymore.
Avoid this null pointer derefence by skipping the call when necessary.
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs).
This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask
definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the
shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is
wrong for 9561."
In real life testing, without this patch the 2.4GHz throughput on
Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to
practical maximum with the patch applied.
In the macb binding documentation "phys" is an optional property. Make
implementation in line with it. This change allows the traditional flow
in which first stage bootloader does PS-GT configuration to work along
with newer use cases in which PS-GT configuration is managed by the
phy-zynqmp driver.
It fixes below macb probe failure when macb DT node doesn't have SGMII
phys handle.
"macb ff0b0000.ethernet: error -ENODEV: failed to get PS-GTR PHY"
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cfb7b8bf1e2d66 ("ASoC: rsnd: tidyup
rsnd_ssiu_busif_err_status_clear()") merged duplicate code, but it didn't
care about default case, and causes smatch warnings.
smatch warnings:
sound/soc/sh/rcar/ssiu.c:112 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'offset'.
sound/soc/sh/rcar/ssiu.c:114 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'shift'.
This patch cares it.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87r15rgn6p.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function si_parse_power_table(), array adev->pm.dpm.ps and its member
is allocated. If the allocation of each member fails, the array itself
is freed and returned with an error code. However, the array is later
freed again in si_dpm_fini() function which is called when the function
returns an error.
This leads to potential double free of the array adev->pm.dpm.ps, as
well as leak of its array members, since the members are not freed in
the allocation function and the array is not nulled when freed.
In addition adev->pm.dpm.num_ps, which keeps track of the allocated
array member, is not updated until the member allocation is
successfully finished, this could also lead to either use after free,
or uninitialized variable access in si_dpm_fini().
Fix this by postponing the free of the array until si_dpm_fini() and
increment adev->pm.dpm.num_ps everytime the array member is allocated.
It needs to check if the pp_funcs is initialized while release the
context, otherwise it will trigger null pointer panic while the software
smu is not enabled.
When PSCI OSI mode is supported the syscore flag is set for the CPU devices
that becomes attached to their PM domains (genpds). In the suspend-to-idle
case, we call dev_pm_genpd_suspend|resume() to allow genpd to properly
manage the power-off/on operations (pick an idlestate and manage the on/off
notifications).
For suspend-to-ram, dev_pm_genpd_suspend|resume() is currently not being
called, which causes a problem that the genpd on/off notifiers do not get
sent as expected. This prevents the platform-specific operations from being
executed, typically needed just before/after the boot CPU is being turned
off/on.
To deal with this problem, let's register a syscore ops for cpuidle-psci
when PSCI OSI mode is being used and call dev_pm_genpd_suspend|resume()
from them. In this way, genpd regains control of the PM domain topology and
then sends the on/off notifications when it's appropriate.
Reported-by: Maulik Shah <quic_mkshah@quicinc.com> Suggested-by: Maulik Shah <quic_mkshah@quicinc.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Maulik Shah <quic_mkshah@quicinc.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
this_cpu_ptr() calls smp_processor_id() in a preemptible context.
Fix by using per_cpu_ptr() with raw_smp_processor_id() instead.
Link: https://lore.kernel.org/r/20220412222008.126521-16-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a potential memory leak in lpfc_ignore_els_cmpl() and
lpfc_els_rsp_reject() that was allocated from NPIV PLOGI_RJT
(lpfc_rcv_plogi()'s login_mbox).
Check if cmdiocb->context_un.mbox was allocated in lpfc_ignore_els_cmpl(),
and then free it back to phba->mbox_mem_pool along with mbox->ctx_buf for
service parameters.
For lpfc_els_rsp_reject() failure, free both the ctx_buf for service
parameters and the login_mbox.
Link: https://lore.kernel.org/r/20220412222008.126521-10-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If lpfc_issue_els_flogi() fails and returns non-zero status, the node
reference count is decremented to trigger the release of the nodelist
structure. However, if there is a prior registration or dev-loss-evt work
pending, the node may be released prematurely. When dev-loss-evt
completes, the released node is referenced causing a use-after-free null
pointer dereference.
Similarly, when processing non-zero ELS PLOGI completion status in
lpfc_cmpl_els_plogi(), the ndlp flags are checked for a transport
registration before triggering node removal. If dev-loss-evt work is
pending, the node may be released prematurely and a subsequent call to
lpfc_dev_loss_tmo_handler() results in a use after free ndlp dereference.
Add test for pending dev-loss before decrementing the node reference count
for FLOGI, PLOGI, PRLI, and ADISC handling.
Link: https://lore.kernel.org/r/20220412222008.126521-9-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix by reordering the taking of the lpfc_cmd->buf_lock and phba->hbalock in
lpfc_abort_handler routine so that it tries to take the lpfc_cmd->buf_lock
first before phba->hbalock.
Link: https://lore.kernel.org/r/20220412222008.126521-7-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The same CPU tries to claim the phba->port_list_lock twice.
Move the cfg_log_verbose checks as part of the lpfc_printf_vlog() and
lpfc_printf_log() macros before calling lpfc_dmp_dbg(). There is no need
to take the phba->port_list_lock within lpfc_dmp_dbg().
Link: https://lore.kernel.org/r/20220412222008.126521-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that the lo_device which is stored in the gendisk private
data is valid until the gendisk is freed. Currently the loop driver
uses a lot of effort to make sure a device is not freed when it is
still in use, but to to fix a potential deadlock this will be relaxed
a bit soon.
The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Suggested-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible when using ASoC that input_dev is unregistered while
calling snd_jack_report, which causes NULL pointer dereference.
In order to prevent this serialize access to input_dev using mutex lock.
The TASKS_RUDE_RCU does not select IRQ_WORK, which can result in build
failures for kernels that do not otherwise select IRQ_WORK. This commit
therefore causes the TASKS_RUDE_RCU Kconfig option to select IRQ_WORK.
Reported-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the cpu_possible_mask is sparse (for example, if bits are set only for
CPUs 0, 4, 8, ...), then rcu_tasks_invoke_cbs() will access per-CPU data
for a CPU not in cpu_possible_mask. It makes these accesses while doing
a workqueue-based binary search for non-empty callback lists. Although
this search must pass through CPUs not represented in cpu_possible_mask,
it has no need to check the callback list for such CPUs.
This commit therefore changes the rcu_tasks_invoke_cbs() function's
binary search so as to only check callback lists for CPUs present in
cpu_possible_mask.
Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit therefore fixes this issue by applying a single-CPU
optimization to the RCU Tasks Rude grace-period process. The key point
here is that the purpose of this RCU flavor is to force a schedule on
each online CPU since some past event. But the rcu_tasks_rude_wait_gp()
function runs in the context of the RCU Tasks Rude's grace-period kthread,
so there must already have been a context switch on the current CPU since
the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude().
So if there is only a single CPU online, RCU Tasks Rude's grace-period
kthread does not need to anything at all.
It turns out that the rcu_tasks_rude_wait_gp() function's call to
schedule_on_each_cpu() causes problems during early boot. During that
time, there is only one online CPU, namely the boot CPU. Therefore,
applying this single-CPU optimization fixes early-boot instances of
this problem.
If drm_universal_plane_init() fails early we jump to the common cleanup code
that calls komeda_plane_destroy() which in turn could access the uninitalised
drm_plane and crash. Return early if an error is detected without going through
the common code.
projects / thirdparty / kernel / stable.git / log
