realloc_argv() was only updating the array size if it was called with
old_argv already allocated. The first time it was called to create an
argv array, it would allocate the array but return the array size as
zero. dm_split_args() would think that it couldn't store any arguments
in the array and would call realloc_argv() again, causing it to
reallocate the initial slots (this time using GPF_KERNEL) and finally
return a size. Aside from being wasteful, this could cause deadlocks on
targets that need to process messages without starting new IO. Instead,
realloc_argv should always update the allocated array size on success.
Fixes: a0651926553c ("dm table: don't copy from a NULL pointer in realloc_argv()") Cc: stable@vger.kernel.org Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function brcmf_usb_dl_writeimage() calls the function
brcmf_usb_dl_cmd() but dose not check its return value. The
'state.state' and the 'state.bytes' are uninitialized if the
function brcmf_usb_dl_cmd() fails. It is dangerous to use
uninitialized variables in the conditions.
Add error handling for brcmf_usb_dl_cmd() to jump to error
handling path if the brcmf_usb_dl_cmd() fails and the
'state.state' and the 'state.bytes' are uninitialized.
Improve the error message to report more detailed error
information.
Fixes: 71bb244ba2fd ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Link: https://patch.msgid.link/20250422042203.2259-1-vulab@iscas.ac.cn Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the XGMAC specification, enabling features such as Layer 3
and Layer 4 Packet Filtering, Split Header and Virtualized Network support
automatically selects the IPC Full Checksum Offload Engine on the receive
side.
When RX checksum offload is disabled, these dependent features must also
be disabled to prevent abnormal behavior caused by mismatched feature
dependencies.
Ensure that toggling RX checksum offload (disabling or enabling) properly
disables or enables all dependent features, maintaining consistent and
expected behavior in the network device.
Cc: stable@vger.kernel.org Fixes: 1a510ccf5869 ("amd-xgbe: Add support for VXLAN offload capabilities") Signed-off-by: Vishal Badole <Vishal.Badole@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250424130248.428865-1-Vishal.Badole@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Camm noticed that on parisc a SIGFPE exception will crash an application with
a second SIGFPE in the signal handler. Dave analyzed it, and it happens
because glibc uses a double-word floating-point store to atomically update
function descriptors. As a result of lazy binding, we hit a floating-point
store in fpe_func almost immediately.
When the T bit is set, an assist exception trap occurs when when the
co-processor encounters *any* floating-point instruction except for a double
store of register %fr0. The latter cancels all pending traps. Let's fix this
by clearing the Trap (T) bit in the FP status register before returning to the
signal handler in userspace.
The issue can be reproduced with this test program:
Deferred probe with pm_runtime_put() may delay clock disable, causing
incorrect clock usage count. Use pm_runtime_put_sync() to ensure the
clock is disabled immediately.
Fixes: 13d6eb20fc79 ("i2c: imx-lpi2c: add runtime pm support") Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Carlos Song <carlos.song@nxp.com> Cc: <stable@vger.kernel.org> # v4.16+ Link: https://lore.kernel.org/r/20250421062341.2471922-1-carlos.song@nxp.com Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nouveau is mostly designed in a way that it's expected that fences only
ever get signaled through nouveau_fence_signal(). However, in at least
one other place, nouveau_fence_done(), can signal fences, too. If that
happens (race) a signaled fence remains in the pending list for a while,
until it gets removed by nouveau_fence_update().
Should nouveau_fence_context_kill() run in the meantime, this would be
a bug because the function would attempt to set an error code on an
already signaled fence.
Have nouveau_fence_context_kill() check for a fence being signaled.
Cc: stable@vger.kernel.org # v5.10+ Fixes: ea13e5abf807 ("drm/nouveau: signal pending fences when channel has been killed") Suggested-by: Christian König <christian.koenig@amd.com> Signed-off-by: Philipp Stanner <phasta@kernel.org> Link: https://lore.kernel.org/r/20250415121900.55719-3-phasta@kernel.org Signed-off-by: Danilo Krummrich <dakr@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seem to be multiple USB device IDs used for these;
the one I have reports as 0b0e:030c when powered on.
(When powered off, it reports as 0b0e:0311.)
The inst function argument is != NULL only for Venus v1 and
we did not migrate v1 to a hfi_platform abstraction yet. So
check for instance != NULL only after hfi_platform_get returns
no error.
In the case where plat->codecs is NULL the variable count is uninitialized
but is being checked to see if it is 0. Fix this by initializing
count to 0.
Fixes: e29929266be1 ("media: venus: Get codecs and capabilities from hfi platform") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After converting to builtin driver, the probe function should not call
__init functions anymore:
>> WARNING: modpost: vmlinux.o(.text+0x8884d4):
Section mismatch in reference from the function exynos_chipid_probe() to the function .init.text:product_id_to_soc_id()
Reported-by: kernel test robot <lkp@intel.com> Fixes: 352bfbb3e023 ("soc: samsung: exynos-chipid: convert to driver and merge exynos-asv") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20210105174440.120041-1-krzk@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c14f7ccc9f5d ("PCI: Assign PCI domain IDs by ida_alloc()")
introduced a use-after-free bug in the bus removal cleanup. The issue was
found with kfence:
[ 19.293351] BUG: KFENCE: use-after-free read in pci_bus_release_domain_nr+0x10/0x70
The stack trace is a bit misleading as dw_pcie_host_deinit() doesn't
directly call pci_bus_release_domain_nr(). The issue turns out to be in
pci_remove_root_bus() which first calls pci_remove_bus() which frees the
struct pci_bus when its struct device is released. Then
pci_bus_release_domain_nr() is called and accesses the freed struct
pci_bus. Reordering these fixes the issue.
Commit 62baf70c3274 caused the ANA log page to be re-read, even on
controllers that do not support ANA. While this should generally
harmless, some controllers hang on the unsupported log page and
never finish probing.
Fixes: 62baf70c3274 ("nvme: re-read ANA log page after ns scan completes") Signed-off-by: Hannes Reinecke <hare@kernel.org> Tested-by: Srikanth Aithal <sraithal@amd.com>
[hch: more detailed commit message] Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xdp: Reset bpf_redirect_info before running a xdp's BPF prog.
Ricardo reported a KASAN discovered use after free in v6.6-stable.
The syzbot starts a BPF program via xdp_test_run_batch() which assigns
ri->tgt_value via dev_hash_map_redirect() and the return code isn't
XDP_REDIRECT it looks like nonsense. So the output in
bpf_warn_invalid_xdp_action() appears once.
Then the TUN driver runs another BPF program (on the same CPU) which
returns XDP_REDIRECT without setting ri->tgt_value first. It invokes
bpf_trace_printk() to print four characters and obtain the required
return value. This is enough to get xdp_do_redirect() invoked which
then accesses the pointer in tgt_value which might have been already
deallocated.
This problem does not affect upstream because since commit 401cb7dae8130 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
the per-CPU variable is referenced via task's task_struct and exists on
the stack during NAPI callback. Therefore it is cleared once before the
first invocation and remains valid within the RCU section of the NAPI
callback.
Instead of performing the huge backport of the commit (plus its fix ups)
here is an alternative version which only resets the variable in
question prior invoking the BPF program.
When `jr3_pci_detach()` is called during device removal, it calls
`timer_delete_sync()` to stop the timer, but the timer expiry function
always reschedules the timer, so the synchronization is ineffective.
Call `timer_shutdown_sync()` instead. It does not matter that the timer
expiry function pointer is cleared, because the device is being removed.
During recovery/check operations, the process_checks function loops
through available disks to find a 'primary' source with successfully
read data.
If no suitable source disk is found after checking all possibilities,
the 'primary' index will reach conf->raid_disks * 2. Add an explicit
check for this condition after the loop. If no source disk was found,
print an error message and return early to prevent further processing
without a valid primary source.
Block validity checks need to be skipped in case they are called
for journal blocks since they are part of system's protected
zone.
Currently, this is done by checking inode->ino against
sbi->s_es->s_journal_inum, which is a direct read from the ext4 sb
buffer head. If someone modifies this underneath us then the
s_journal_inum field might get corrupted. To prevent against this,
change the check to directly compare the inode with journal->j_inode.
**Slight change in behavior**: During journal init path,
check_block_validity etc might be called for journal inode when
sbi->s_journal is not set yet. In this case we now proceed with
ext4_inode_block_valid() instead of returning early. Since systems zones
have not been set yet, it is okay to proceed so we can perform basic
checks on the blocks.
Suggested-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Zhang Yi <yi.zhang@huawei.com> Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com> Link: https://patch.msgid.link/0c06bc9ebfcd6ccfed84a36e79147bf45ff5adc1.1743142920.git.ojaswin@linux.ibm.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
eIBRS protects against guest->host RSB underflow/poisoning attacks.
Adding retpoline to the mix doesn't change that. Retpoline has a
balanced CALL/RET anyway.
So the current full RSB filling on VMEXIT with eIBRS+retpoline is
overkill. Disable it or do the VMEXIT_LITE mitigation if needed.
Suggested-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Reviewed-by: Amit Shah <amit.shah@amd.com> Reviewed-by: Nikolay Borisov <nik.borisov@suse.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Sean Christopherson <seanjc@google.com> Cc: David Woodhouse <dwmw2@infradead.org> Link: https://lore.kernel.org/r/84a1226e5c9e2698eae1b5ade861f1b8bf3677dc.1744148254.git.jpoimboe@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
write_ibpb() does IBPB, which (among other things) flushes branch type
predictions on AMD. If the CPU has SRSO_NO, or if the SRSO mitigation
has been disabled, branch type flushing isn't needed, in which case the
lighter-weight SBPB can be used.
The 'x86_pred_cmd' variable already keeps track of whether IBPB or SBPB
should be used. Use that instead of hardcoding IBPB.
When running the mincore_selftest on a system with an XFS file system, it
failed the "check_file_mmap" test case due to the read-ahead pages reaching
the end of the file. The failure log is as below:
RUN global.check_file_mmap ...
mincore_selftest.c:264:check_file_mmap:Expected i (1024) < vec_size (1024)
mincore_selftest.c:265:check_file_mmap:Read-ahead pages reached the end of the file
check_file_mmap: Test failed
FAIL global.check_file_mmap
This is because the read-ahead window size of the XFS file system on this
machine is 4 MB, which is larger than the size from the #PF address to the
end of the file. As a result, all the pages for this file are populated.
This issue can be fixed by extending the current FILE_SIZE 4MB to a larger
number, but it will still fail if the read-ahead window size of the file
system is larger enough. Additionally, in the real world, read-ahead pages
reaching the end of the file can happen and is an expected behavior.
Therefore, allowing read-ahead pages to reach the end of the file is a
better choice for the "check_file_mmap" test case.
Scanning for namespaces can take some time, so if the target is
reconfigured while the scan is running we may miss a Attached Namespace
Attribute Changed AEN.
Check if the NVME_AER_NOTICE_NS_CHANGED bit is set once the scan has
finished, and requeue scanning to pick up any missed change.
Signed-off-by: Hannes Reinecke <hare@kernel.org> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
idt_scan_mws() puts a large fixed-size array on the stack and copies
it into a smaller dynamically allocated array at the end. On 32-bit
targets, the fixed size can easily exceed the warning limit for
possible stack overflow:
Change it to instead just always use dynamic allocation for the
array from the start. It's too big for the stack, but not actually
all that much for a permanent allocation.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/all/202205111109.PiKTruEj-lkp@intel.com/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org>
If 'port_id' is negative, the shift counts in wcd934x_slim_irq_handler()
also become negative, resulting in undefined behavior due to shift out
of bounds.
If I'm reading the code correctly, that appears to be not possible, but
with KCOV enabled, Clang's range analysis isn't always able to determine
that and generates undefined behavior.
As a result the code generation isn't optimal, and undefined behavior
should be avoided regardless. Improve code generation and remove the
undefined behavior by converting the signed variables to unsigned.
Fixes the following warning with UBSAN:
sound/soc/codecs/snd-soc-wcd934x.o: warning: objtool: .text.wcd934x_slim_irq_handler: unexpected end of section
The variable d->name, returned by devm_kasprintf(), could be NULL.
A pointer check is added to prevent potential NULL pointer dereference.
This is similar to the fix in commit 3027e7b15b02
("ice: Fix some null pointer dereference issues in ice_ptp.c").
Change the "wait for operation finish" logic to take interrupts into
account.
When using dmatest with idxd DMA engine, it's possible that during
longer tests, the interrupt notifying the finish of an operation
happens during wait_event_freezable_timeout(), which causes dmatest to
cleanup all the resources, some of which might still be in use.
This fix ensures that the wait logic correctly handles interrupts,
preventing premature cleanup of resources.
Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202502171134.8c403348-lkp@intel.com Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20250305230007.590178-1-vinicius.gomes@intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"maxim,max3421" DT compatible is missing its SPI device ID entry, not
allowing module autoloading and leading to the following message:
"SPI driver max3421-hcd has no spi_device_id for maxim,max3421"
As reported by the kernel test robot, the following error occurs:
arch/parisc/kernel/pdt.c:65:6: warning: no previous prototype for 'arch_report_meminfo' [-Wmissing-prototypes]
65 | void arch_report_meminfo(struct seq_file *m)
| ^~~~~~~~~~~~~~~~~~~
arch_report_meminfo() is declared in include/linux/proc_fs.h and only
defined when CONFIG_PROC_FS is enabled. Wrap its definition in #ifdef
CONFIG_PROC_FS to fix the -Wmissing-prototypes warning.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202502082315.IPaHaTyM-lkp@intel.com/ Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_clk_get_hw_from_clkspec() checks all available clock-providers by
comparing their of nodes to the one from the clkspec. If no matching
clock provider is found, the function returns -EPROBE_DEFER to cause a
re-check at a later date. If a matching clock provider is found, an
authoritative answer can be retrieved from it whether the clock exists
or not.
This does not take into account that the clock-provider may never
appear, because it's node is disabled. This can happen when a clock is
optional, provided by a separate block which never gets enabled.
One example of this happening is the rk3588's VOP, which has optional
additional display clocks coming from PLLs inside the hdmiphy blocks.
These can be used for better rates, but the system will also work
without them.
The problem around that is described in the followups to[1]. As we
already know the of node of the presumed clock provider, add a check via
of_device_is_available() whether this is a "valid" device node. This
prevents eternal defer loops.
Some information that should be retrieved at runtime for the Coherence
Manager can be either absent or wrong. This patch allows checking if
some of this information is available from the device tree and updates
the internal variable accordingly.
For now, only the compatible string associated with the broken HCI is
being retrieved.
The SanDisk 3.2Gen1 Flash Drive, which VID:PID is in 0781:55a3,
just like Silicon Motion Flash Drive:
https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
also needs the DELAY_INIT quirk, or it will randomly work incorrectly
(e.g.: lsusb and can't list this device info) when connecting Huawei
hisi platforms and doing thousand of reboot test circles.
Silicon Motion Flash Drive connects to Huawei hisi platforms and
performs a system reboot test for two thousand circles, it will
randomly work incorrectly on boot, set DELAY_INIT quirk can workaround
this issue.
The event count is read from register DWC3_GEVNTCOUNT.
There is a check for the count being zero, but not for exceeding the
event buffer length.
Check that event count does not exceed event buffer length,
avoiding an out-of-bounds access when memcpy'ing the event.
Crash log:
Unable to handle kernel paging request at virtual address ffffffc0129be000
pc : __memcpy+0x114/0x180
lr : dwc3_check_event_buf+0xec/0x348
x3 : 0000000000000030 x2 : 000000000000dfc4
x1 : ffffffc0129be000 x0 : ffffff87aad60080
Call trace:
__memcpy+0x114/0x180
dwc3_interrupt+0x24/0x34
The OHCI controller (rev 0x02) under LS7A PCI host has a hardware flaw.
MMIO register with offset 0x60/0x64 is treated as legacy PS2-compatible
keyboard/mouse interface, which confuse the OHCI controller. Since OHCI
only use a 4KB BAR resource indeed, the LS7A OHCI controller's 32KB BAR
is wrapped around (the second 4KB BAR space is the same as the first 4KB
internally). So we can add an 4KB offset (0x1000) to the OHCI registers
(from the PCI BAR resource) as a quirk.
The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit 58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget").
Under PREEMPT_RT the deadlock can be readily triggered by heavy network
traffic, for example using "iperf --bidir" over NCM ethernet link.
The deadlock occurs because the threaded interrupt handler gets
preempted by a softirq, but both are protected by the same spinlock.
Prevent deadlock by disabling softirq during threaded irq handler.
Cc: stable <stable@kernel.org> Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver") Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Acked-by: Peter Chen <peter.chen@kernel.org> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20250318-rfs-cdns3-deadlock-v2-1-bfd9cfcee732@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for OWON HDS200 series oscilloscopes and likely
many other pieces of OWON test equipment.
OWON HDS200 series devices host two USB endpoints, designed to
facilitate bidirectional SCPI. SCPI is a predominately ASCII text
protocol for test/measurement equipment. Having a serial/tty interface
for these devices lowers the barrier to entry for anyone trying to
write programs to communicate with them.
The following shows the USB descriptor for the OWON HDS272S running
firmware V5.7.1:
Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 [unknown]
bDeviceSubClass 0 [unknown]
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x5345 Owon
idProduct 0x1234 PDS6062T Oscilloscope
bcdDevice 1.00
iManufacturer 1 oscilloscope
iProduct 2 oscilloscope
iSerial 3 oscilloscope
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0029
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 5 Physical Interface Device
bInterfaceSubClass 0 [unknown]
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 09 21 11 01 00 01 22 5f 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Device Status: 0x0000
(Bus Powered)
OWON appears to be using the same USB Vendor and Product ID for many
of their oscilloscopes. Looking at the discussion about the USB
vendor/product ID, in the link bellow, suggests that this VID/PID is
shared with VDS, SDS, PDS, and now the HDS series oscilloscopes.
Available documentation for these devices seems to indicate that all
use a similar SCPI protocol, some with RS232 options. It is likely that
this same simple serial setup would work correctly for them all.
Abacus Electrics makes optical probes for interacting with smart meters
over an optical interface.
At least one version uses an FT232B chip (as detected by ftdi_sio) with
a custom USB PID, which needs to be added to the list to make the device
work in a plug-and-play fashion.
Signed-off-by: Michael Ehrenreich <michideep@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore an IRTE back to host control (remapped or posted MSI mode) if the
*new* GSI route prevents posting the IRQ directly to a vCPU, regardless of
the GSI routing type. Updating the IRTE if and only if the new GSI is an
MSI results in KVM leaving an IRTE posting to a vCPU.
The dangling IRTE can result in interrupts being incorrectly delivered to
the guest, and in the worst case scenario can result in use-after-free,
e.g. if the VM is torn down, but the underlying host IRQ isn't freed.
Fixes: efc644048ecd ("KVM: x86: Update IRTE for posted-interrupts") Fixes: 411b44ba80ab ("svm: Implements update_pi_irte hook to setup posted interrupt") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In chameleon_parse_gdd(), if mcb_device_register() fails, 'mdev'
would be released in mcb_device_register() via put_device().
Thus, goto 'err' label and free 'mdev' again causes a double free.
Just return if mcb_device_register() fails.
Allocate SVM's interrupt remapping metadata using GFP_ATOMIC as
svm_ir_list_add() is called with IRQs are disabled and irqfs.lock held
when kvm_irq_routing_update() reacts to GSI routing changes.
Fixes: 411b44ba80ab ("svm: Implements update_pi_irte hook to setup posted interrupt") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per virtio spec the fields cols and rows are specified as little
endian. Although there is no legacy interface requirement that would
state that cols and rows need to be handled as native endian when legacy
interface is used, unlike for the fields of the adjacent struct
virtio_console_control, I decided to err on the side of caution based
on some non-conclusive virtio spec repo archaeology and opt for using
virtio16_to_cpu() much like for virtio_console_control.event. Strictly
by the letter of the spec virtio_le_to_cpu() would have been sufficient.
But when the legacy interface is not used, it boils down to the same.
And when using the legacy interface, the device formatting these as
little endian when the guest is big endian would surprise me more than
it using guest native byte order (which would make it compatible with
the current implementation). Nevertheless somebody trying to implement
the spec following it to the letter could end up forcing little endian
byte order when the legacy interface is in use. So IMHO this ultimately
needs a judgement call by the maintainers.
Fixes: 8345adbf96fc1 ("virtio: console: Accept console size along with resize control message") Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Cc: stable@vger.kernel.org # v2.6.35+
Message-Id: <20250322002954.3129282-1-pasic@linux.ibm.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EINVAL instead of success if amd_ir_set_vcpu_affinity() is
invoked without use_vapic; lying to KVM about whether or not the IRTE was
configured to post IRQs is all kinds of bad.
Fixes: d98de49a53e4 ("iommu/amd: Enable vAPIC interrupt remapping mode by default") Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-6-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes a Use-After-Free vulnerability in the HFSC qdisc class
handling. The issue occurs due to a time-of-check/time-of-use condition
in hfsc_change_class() when working with certain child qdiscs like netem
or codel.
The vulnerability works as follows:
1. hfsc_change_class() checks if a class has packets (q.qlen != 0)
2. It then calls qdisc_peek_len(), which for certain qdiscs (e.g.,
codel, netem) might drop packets and empty the queue
3. The code continues assuming the queue is still non-empty, adding
the class to vttree
4. This breaks HFSC scheduler assumptions that only non-empty classes
are in vttree
5. Later, when the class is destroyed, this can lead to a Use-After-Free
The fix adds a second queue length check after qdisc_peek_len() to verify
the queue wasn't emptied.
Fixes: 21f4d5cc25ec ("net_sched/hfsc: fix curve activation in hfsc_change_class()") Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Reviewed-by: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20250417184732.943057-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a racing condition between workqueue created when enabling
bearer and another thread created when disabling bearer right after
that as follow:
A network restart test on a router led to an out-of-memory condition,
which was traced to a memory leak in the PHY LED trigger code.
The root cause is misuse of the devm API. The registration function
(phy_led_triggers_register) is called from phy_attach_direct, not
phy_probe, and the unregister function (phy_led_triggers_unregister)
is called from phy_detach, not phy_remove. This means the register and
unregister functions can be called multiple times for the same PHY
device, but devm-allocated memory is not freed until the driver is
unbound.
This also prevents kmemleak from detecting the leak, as the devm API
internally stores the allocated pointer.
Fix this by replacing devm_kzalloc/devm_kcalloc with standard
kzalloc/kcalloc, and add the corresponding kfree calls in the unregister
path.
Fixes: 3928ee6485a3 ("net: phy: leds: Add support for "link" trigger") Fixes: 2e0bc452f472 ("net: phy: leds: add support for led triggers on phy link state change") Signed-off-by: Hao Guan <hao.guan@siflower.com.cn> Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250417032557.2929427-1-dqfext@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
cpufreq_cpu_get_raw() can return NULL when the target CPU is not present
in the policy->cpus mask. scpi_cpufreq_get_rate() does not check for
this case, which results in a NULL pointer dereference.
The page_link lower bits of the first sg could contain something like
SG_END, if we are mapping a single VRAM page or contiguous blob which
fits into one sg entry. Rather pull out the struct page, and use that in
our check to know if we mapped struct pages vs VRAM.
Fixes: f44ffd677fb3 ("drm/amdgpu: add support for exporting VRAM using DMA-buf v3") Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Christian König <christian.koenig@amd.com> Cc: amd-gfx@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v5.8+ Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently callers have to provide handle of amdgpu_device,
which is not used by the implementation. It is unlikely this
parameter will become useful in future, thus removing it
v2: squash in unused variable fix
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: c0dd8a9253fa ("drm/amdgpu/dma_buf: fix page_link check") Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/gpu/drm/amd/amdgpu/amdgpu_vram_mgr.c:648: warning: Function parameter or member 'dev' not described in 'amdgpu_vram_mgr_free_sgt'
drivers/gpu/drm/amd/amdgpu/amdgpu_vram_mgr.c:648: warning: Function parameter or member 'dir' not described in 'amdgpu_vram_mgr_free_sgt'
Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: amd-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: c0dd8a9253fa ("drm/amdgpu/dma_buf: fix page_link check") Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if the filesystem for the cgroups version it wants to use is not
mounted charge_reserved_hugetlb.sh and hugetlb_reparenting_test.sh tests
will attempt to mount it on the hard coded path /dev/cgroup/memory,
deleting that directory when the test finishes. This will fail if there
is not a preexisting directory at that path, and since the directory is
deleted subsequent runs of the test will fail. Instead of relying on this
hard coded directory name use mktemp to generate a temporary directory to
use as a mountpoint, fixing both the assumption and the disruption caused
by deleting a preexisting directory.
This means that if the relevant cgroup filesystem is not already mounted
then we rely on having coreutils (which provides mktemp) installed. I
suspect that many current users are relying on having things automounted
by default, and given that the script relies on bash it's probably not an
unreasonable requirement.
Link: https://lkml.kernel.org/r/20250404-kselftest-mm-cgroup2-detection-v1-1-3dba6d32ba8c@kernel.org Fixes: 209376ed2a84 ("selftests/vm: make charge_reserved_hugetlb.sh work with existing cgroup setting") Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Aishwarya TCV <aishwarya.tcv@arm.com> Cc: Mark Brown <broonie@kernel.org> Cc: Mina Almasry <almasrymina@google.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Waiman Long <longman@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Replace assignment of PCI domain IDs from atomic_inc_return() to
ida_alloc().
Use two IDAs, one for static domain allocations (those which are defined in
device tree) and second for dynamic allocations (all other).
During removal of root bus / host bridge, also release the domain ID. The
released ID can be reused again, for example when dynamically loading and
unloading native PCI host bridge drivers.
This change also allows to mix static device tree assignment and dynamic by
kernel as all static allocations are reserved in dynamic pool.
[bhelgaas: set "err" if "bus->domain_nr < 0"] Link: https://lore.kernel.org/r/20220714184130.5436-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stable-dep-of: 804443c1f278 ("PCI: Fix reference leak in pci_register_host_bridge()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we retrieve the PCI domain number of the host bridge from the
bus sysdata (or pci_config_window if PCI_DOMAINS_GENERIC=y). Actually
we have the information at PCI host bridge probing time, and it makes
sense that we store it into pci_host_bridge. One benefit of doing so is
the requirement for supporting PCI on Hyper-V for ARM64, because the
host bridge of Hyper-V doesn't have pci_config_window, whereas ARM64 is
a PCI_DOMAINS_GENERIC=y arch, so we cannot retrieve the PCI domain
number from pci_config_window on ARM64 Hyper-V guest.
As the preparation for ARM64 Hyper-V PCI support, we introduce the
domain_nr in pci_host_bridge and a sentinel value to allow drivers to
set domain numbers properly at probing time. Currently
CONFIG_PCI_DOMAINS_GENERIC=y archs are only users of this
newly-introduced field.
The ad7768-1 ADC output code is two's complement, meaning that the voltage
conversion result is a signed value.. Since the value is a 24 bit one,
stored in a 32 bit variable, the sign should be extended in order to get
the correct representation.
Also the channel description has been updated to signed representation,
to match the ADC specifications.
The data used is all in local variables so there is no advantage
in setting *val = ret with the direct mode claim held.
Move it later to after error check.
soc_dev_attr->revision could be NULL, thus,
a pointer check is added to prevent potential NULL pointer dereference.
This is similar to the fix in commit 3027e7b15b02
("ice: Fix some null pointer dereference issues in ice_ptp.c").
Old Exynos SoCs have both Product ID and Revision ID in one single
register, while new SoCs tend to have two separate registers for those
IDs. Implement handling of both cases by passing Revision ID register
offsets in driver data.
Previously existing macros for Exynos4210 (removed in this patch) were
incorrect:
soc_device_to_device() seems to be discouraged [1] so remove it in favor
of printing info message with platform device. This will only change
the prefix in the info message from "soc soc0: " to "exynos-chipid 10000000.chipid:".
The Exynos Chip ID driver on Exynos SoCs has so far only informational
purpose - to expose the SoC device in sysfs. No other drivers depend on
it so there is really no benefit of initializing it early.
The code would be the most flexible if converted to a regular driver.
However there is already another driver - Exynos ASV (Adaptive Supply
Voltage) - which binds to the device node of Chip ID.
The solution is to convert the Exynos Chip ID to a built in driver and
merge the Exynos ASV into it.
This has several benefits:
1. Although the Exynos ASV driver binds to a device node present in all
Exynos DTS (generic compatible), it fails to probe except on the
supported ones (only Exynos5422). This means that the regular boot
process has a planned/normal device probe failure.
Merging the ASV into Chip ID will remove this probe failure because
the final driver will always bind, just with disabled ASV features.
2. Allows to use dev_info() as the SoC bus is present (since
core_initcall).
3. Could speed things up because of execution of Chip ID code in a SMP
environment (after bringing up secondary CPUs, unlike early_initcall),
This reduces the amount of work to be done early, when the kernel has
to bring up critical devices.
The Exynos ChipID driver on Exynos SoCs has only informational
purpose - to expose the SoC device in sysfs. No other drivers
depend on it so there is really no benefit of initializing it early.
Instead, initialize everything with arch_initcall which:
1. Allows to use dev_info() as the SoC bus is present (since
core_initcall),
2. Could speed things up because of execution in a SMP environment
(after bringing up secondary CPUs, unlike early_initcall),
3. Reduces the amount of work to be done early, when the kernel has to
bring up critical devices.
words_count denotes the number of words in total payload, while data
points to payload of various property within it. When words_count
reaches last word, data can access memory beyond the total payload. This
can lead to OOB access. With this patch, the utility api for handling
individual properties now returns the size of data consumed. Accordingly
remaining bytes are calculated before parsing the payload, thereby
eliminates the OOB access possibilities.
Introduce a new hfi platform to cover differences between hfi
versions. As a start move vpp/vsp freq data in that hfi
platform, more platform data will come later.
The hfi_session_init can be called many times and it returns
EINVAL when the session was already initialized. This error code
(EINVAL) is confusing for the callers. Change hfi_session_init to
return EALREADY error code when the session has been already
initialized.
Currently we rely on firmware to return error when we reach the maximum
supported number of sessions. But this errors are happened at reqbuf
time which is a bit later. The more reasonable way looks like is to
return the error on driver open.
To achieve that modify hfi_session_create to return error when we reach
maximum count of sessions and thus refuse open.
Syzkaller has reported a general protection fault at function
ir_raw_event_store_with_filter(). This crash is caused by a NULL pointer
dereference of dev->raw pointer, even though it is checked for NULL in
the same function, which means there is a race condition. It occurs due
to the incorrect order of actions in the streamzap_disconnect() function:
rc_unregister_device() is called before usb_kill_urb(). The dev->raw
pointer is freed and set to NULL in rc_unregister_device(), and only
after that usb_kill_urb() waits for in-progress requests to finish.
If rc_unregister_device() is called while streamzap_callback() handler is
not finished, this can lead to accessing freed resources. Thus
rc_unregister_device() should be called after usb_kill_urb().
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 8e9e60640067 ("V4L/DVB: staging/lirc: port lirc_streamzap to ir-core") Cc: stable@vger.kernel.org Reported-by: syzbot+34008406ee9a31b13c73@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=34008406ee9a31b13c73 Signed-off-by: Murad Masimov <m.masimov@mt-integration.ru> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
