Syzkaller reports [1] hitting a warning which is caused by presence
of a wrong endpoint type at the URB sumbitting stage. While there
was a check for a specific 4th endpoint, since it can switch types
between bulk and interrupt, other endpoints are trusted implicitly.
Similar warning is triggered in a couple of other syzbot issues [2].
Fix the issue by doing a comprehensive check of all endpoints
taking into account difference between high- and full-speed
configuration.
The via-macii ADB driver calls request_irq() after disabling hard
interrupts. But disabling interrupts isn't necessary here because the
VIA shift register interrupt was masked during VIA1 initialization.
This came while reviewing commit c4e86b4363ac ("net: add two more
call_rcu_hurry()").
Paolo asked if adding one synchronize_rcu() would help.
While synchronize_rcu() does not help, making sure to call
rcu_barrier() before msleep(wait) is definitely helping
to make sure lazy call_rcu() are completed.
Instead of waiting ~100 seconds in my tests, the ref_tracker
splats occurs one time only, and netdev_wait_allrefs_any()
latency is reduced to the strict minimum.
Ideally we should audit our call_rcu() users to make sure
no refcount (or cascading call_rcu()) is held too long,
because rcu_barrier() is quite expensive.
Instead of of_clk_get_by_name() use devm_clk_get_prepared() which has
several advantages:
- Combines getting the clock and a call to clk_prepare(). The latter
can be dropped from sti_pwm_probe() accordingly.
- Cares for calling clk_put() which is missing in both probe's error
path and the remove function.
- Cares for calling clk_unprepare() which can be dropped from the error
paths and the remove function. (Note that not all error path got this
right.)
With additionally using devm_pwmchip_add() instead of pwmchip_add() the
remove callback can be dropped completely. With it the last user of
platform_get_drvdata() goes away and so platform_set_drvdata() can be
dropped from the probe function, too.
This prepares the driver for further changes that will drop struct
pwm_chip chip from struct sti_pwm_chip. Use the pwm_chip as driver data
instead of the sti_pwm_chip to get access to the pwm_chip in
sti_pwm_remove() without using pc->chip.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
88E6250-family switches have the quirk that the EEPROM Running flag can
get stuck at 1 when no EEPROM is connected, causing
mv88e6xxx_g2_eeprom_wait() to time out. We still want to wait for the
EEPROM however, to avoid interrupting a transfer and leaving the EEPROM
in an invalid state.
The condition to wait for recommended by the hardware spec is the EEInt
flag, however this flag is cleared on read, so before the hardware reset,
is may have been cleared already even though the EEPROM has been read
successfully.
For this reason, we revive the mv88e6xxx_g1_wait_eeprom_done() function
that was removed in commit 6ccf50d4d474
("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent") in a
slightly refactored form, and introduce a new
mv88e6xxx_g1_wait_eeprom_done_prereset() that additionally handles this
case by triggering another EEPROM reload that can be waited on.
On other switch models without this quirk, mv88e6xxx_g2_eeprom_wait() is
kept, as it avoids the additional reload.
Fixes: 6ccf50d4d474 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of calling mv88e6xxx_g2_eeprom_wait() directly from
mv88e6xxx_hardware_reset(), add configurable pre- and post-reset hard
reset handlers. Initially, the handlers are set to
mv88e6xxx_g2_eeprom_wait() for all families that have get/set_eeprom()
to match the existing behavior. No functional change intended (except
for additional error messages on failure).
Fixes: 6ccf50d4d474 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/wireless/ath/ath10k/debugfs_sta.c:line 429, column 3
Value stored to 'ret' is never read.
Return 'ret' rather than 'count' when 'ret' stores an error code.
Fixes: ee8b08a1be82 ("ath10k: add debugfs support to get per peer tids log via tracing") Signed-off-by: Su Hui <suhui@nfschina.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422034243.938962-1-suhui@nfschina.com Signed-off-by: Sasha Levin <sashal@kernel.org>
compute_intercept_slope() is called from calibrate_8960() (in tsens-8960.c)
as compute_intercept_slope(priv, p1, NULL, ONE_PT_CALIB) which lead to null
pointer dereference (if DEBUG or DYNAMIC_DEBUG set).
Fix this bug by adding null pointer check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: dfc1193d4dbd ("thermal/drivers/tsens: Replace custom 8960 apis with generic apis") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20240411114021.12203-1-amishin@t-argos.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
On x86, the ordinary, position dependent small and kernel code models
only support placement of the executable in 32-bit addressable memory,
due to the use of 32-bit signed immediates to generate references to
global variables. For the kernel, this implies that all global variables
must reside in the top 2 GiB of the kernel virtual address space, where
the implicit address bits 63:32 are equal to sign bit 31.
This means the kernel code model is not suitable for other bare metal
executables such as the kexec purgatory, which can be placed arbitrarily
in the physical address space, where its address may no longer be
representable as a sign extended 32-bit quantity. For this reason,
commit
e16c2983fba0 ("x86/purgatory: Change compiler flags from -mcmodel=kernel to -mcmodel=large to fix kexec relocation errors")
switched to the large code model, which uses 64-bit immediates for all
symbol references, including function calls, in order to avoid relying
on any assumptions regarding proximity of symbols in the final
executable.
The large code model is rarely used, clunky and the least likely to
operate in a similar fashion when comparing GCC and Clang, so it is best
avoided. This is especially true now that Clang 18 has started to emit
executable code in two separate sections (.text and .ltext), which
triggers an issue in the kexec loading code at runtime.
The SUSE bugzilla fixes tag points to gcc 13 having issues with the
large model too and that perhaps the large model should simply not be
used at all.
Instead, use the position independent small code model, which makes no
assumptions about placement but only about proximity, where all
referenced symbols must be within -/+ 2 GiB, i.e., in range for a
RIP-relative reference. Use hidden visibility to suppress the use of a
GOT, which carries absolute addresses that are not covered by static ELF
relocations, and is therefore incompatible with the kexec loader's
relocation logic.
[ bp: Massage commit message. ]
Fixes: e16c2983fba0 ("x86/purgatory: Change compiler flags from -mcmodel=kernel to -mcmodel=large to fix kexec relocation errors") Fixes: https://bugzilla.suse.com/show_bug.cgi?id=1211853 Closes: https://github.com/ClangBuiltLinux/linux/issues/2016 Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Fangrui Song <maskray@google.com> Acked-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/all/20240417-x86-fix-kexec-with-llvm-18-v1-0-5383121e8fb7@kernel.org/ Signed-off-by: Sasha Levin <sashal@kernel.org>
As of commit 7d1d86518118 ("[SCSI] libsas: fix false positive 'device
attached' conditions"), reset the phy->entacted_sas_addr address to a
zero-address when the link rate is less than 1.5G.
Currently we find that when a new device is attached, and the link rate is
less than 1.5G, but the device type is not NO_DEVICE, for example: the link
rate is SAS_PHY_RESET_IN_PROGRESS and the device type is stp. After setting
the phy->entacted_sas_addr address to the zero address, the port will
continue to be created for the phy with the zero-address, and other phys
with the zero-address will be tried to be added to the new port:
[562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached: 0000000000000000 (no device)
// phy19 is deleted but still on the parent port's phy_list
[562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached
[562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached: 0000000000000000 (stp)
[562240.062680] port-7:7:0: trying to add phy phy-7:7:19 fails: it's already part of another port
Therefore, it should be the same as sas_get_phy_attached_dev(). Only when
device_type is SAS_PHY_UNUSED, sas_address is set to the 0 address.
Fixes: 7d1d86518118 ("[SCSI] libsas: fix false positive 'device attached' conditions") Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20240312141103.31358-5-yangxingui@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
cppc_cpufreq_get_rate() and hisi_cppc_cpufreq_get_rate() can be called from
different places with various parameters. So cpufreq_cpu_get() can return
null as 'policy' in some circumstances.
Fix this bug by adding null return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a28b2bfc099c ("cppc_cpufreq: replace per-cpu data array with a list") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We've observed a 7-12% performance regression in iperf3 UDP ipv4 and
ipv6 tests with multiple sockets on Zen3 cpus, which we traced back to
commit f0ea27e7bfe1 ("udp: re-score reuseport groups when connected
sockets are present"). The failing tests were those that would spawn
UDP sockets per-cpu on systems that have a high number of cpus.
Unsurprisingly, it is not caused by the extra re-scoring of the reused
socket, but due to the compiler no longer inlining compute_score, once
it has the extra call site in udp4_lib_lookup2. This is augmented by
the "Safe RET" mitigation for SRSO, needed in our Zen3 cpus.
We could just explicitly inline it, but compute_score() is quite a large
function, around 300b. Inlining in two sites would almost double
udp4_lib_lookup2, which is a silly thing to do just to workaround a
mitigation. Instead, this patch shuffles the code a bit to avoid the
multiple calls to compute_score. Since it is a static function used in
one spot, the compiler can safely fold it in, as it did before, without
increasing the text size.
With this patch applied I ran my original iperf3 testcases. The failing
cases all looked like this (ipv4):
iperf3 -c 127.0.0.1 --udp -4 -f K -b $R -l 8920 -t 30 -i 5 -P 64 -O 2
where $R is either 1G/10G/0 (max, unlimited). I ran 3 times each.
baseline is v6.9-rc3. harmean == harmonic mean; CV == coefficient of
variation.
This restores the performance we had before the change above with this
benchmark. We obviously don't expect any real impact when mitigations
are disabled, but just to be sure it also doesn't regresses:
Cc: Lorenz Bauer <lmb@isovalent.com> Fixes: f0ea27e7bfe1 ("udp: re-score reuseport groups when connected sockets are present") Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are currently four copies of reuseport_lookup: one each for
(TCP, UDP)x(IPv4, IPv6). This forces us to duplicate all callers of
those functions as well. This is already the case for sk_lookup
helpers (inet,inet6,udp4,udp6)_lookup_run_bpf.
There are two differences between the reuseport_lookup helpers:
1. They call different hash functions depending on protocol
2. UDP reuseport_lookup checks that sk_state != TCP_ESTABLISHED
Move the check for sk_state into the caller and use the INDIRECT_CALL
infrastructure to cut down the helpers to one per IP version.
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: Lorenz Bauer <lmb@isovalent.com> Link: https://lore.kernel.org/r/20230720-so-reuseport-v6-4-7021b683cdae@isovalent.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Stable-dep-of: 50aee97d1511 ("udp: Avoid call to compute_score on multiple sites") Signed-off-by: Sasha Levin <sashal@kernel.org>
Rename the existing reuseport helpers for IPv4 and IPv6 so that they
can be invoked in the follow up commit. Export them so that building
DCCP and IPv6 as a module works.
No change in functionality.
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: Lorenz Bauer <lmb@isovalent.com> Link: https://lore.kernel.org/r/20230720-so-reuseport-v6-3-7021b683cdae@isovalent.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Stable-dep-of: 50aee97d1511 ("udp: Avoid call to compute_score on multiple sites") Signed-off-by: Sasha Levin <sashal@kernel.org>
The exit() callback is optional and shouldn't be called without checking
a valid pointer first.
Also, we must clear freq_table pointer even if the exit() callback isn't
present.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Fixes: 91a12e91dc39 ("cpufreq: Allow light-weight tear down and bring up of CPUs") Fixes: f339f3541701 ("cpufreq: Rearrange locking in cpufreq_remove_dev()") Reported-by: Lizhe <sensor1010@163.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, cpufreq_remove_dev() invokes the ->exit() driver callback
without holding the policy rwsem which is inconsistent with what
happens if ->exit() is invoked directly from cpufreq_offline().
It also manipulates the real_cpus mask and removes the CPU device
symlink without holding the policy rwsem, but cpufreq_offline() holds
the rwsem around the modifications thereof.
For consistency, modify cpufreq_remove_dev() to hold the policy rwsem
until the ->exit() callback has been called (or it has been determined
that it is not necessary to call it).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Stable-dep-of: b8f85833c057 ("cpufreq: exit() callback is optional") Signed-off-by: Sasha Levin <sashal@kernel.org>
Split the "core" part running under the policy rwsem out of
cpufreq_offline() to allow the locking in cpufreq_remove_dev() to be
rearranged more easily.
As a side-effect this eliminates the unlock label that's not needed
any more.
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Stable-dep-of: b8f85833c057 ("cpufreq: exit() callback is optional") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3e11e53041502 tries to suppress dlm_lock() lock conversion errors
that occur when the lockspace has already been released.
It does that by setting and checking the SDF_SKIP_DLM_UNLOCK flag. This
conflicts with the intended meaning of the SDF_SKIP_DLM_UNLOCK flag, so
check whether the lockspace is still allocated instead.
(Given the current DLM API, checking for this kind of error after the
fact seems easier that than to make sure that the lockspace is still
allocated before calling dlm_lock(). Changing the DLM API so that users
maintain the lockspace references themselves would be an option.)
Fixes: 3e11e53041502 ("GFS2: ignore unlock failures after withdraw") Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit fffe9bee14b0 ("gfs2: Delay withdraw from atomic context")
switched from gfs2_withdraw() to gfs2_withdraw_delayed() in
gfs2_ail_error(), but failed to then check if a delayed withdraw had
occurred. Fix that by adding the missing check in __gfs2_ail_flush(),
where the spin locks are already dropped and a withdraw is possible.
Fixes: fffe9bee14b0 ("gfs2: Delay withdraw from atomic context") Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code works as intended, and the warning could be addressed by using
a memcpy(), but turning the warning off for this file works equally well
and may be easier to merge.
Currently, the UIC_COMMAND_COMPL interrupt is disabled and a wmb() is used
to complete the register write before any following writes.
wmb() ensures the writes complete in that order, but completion doesn't
mean that it isn't stored in a buffer somewhere. The recommendation for
ensuring this bit has taken effect on the device is to perform a read back
to force it to make it all the way to the device. This is documented in
device-io.rst and a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the wmb()'s
purpose wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: d75f7fe495cf ("scsi: ufs: reduce the interrupts for power mode change requests") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-9-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, interrupts are cleared and disabled prior to registering the
interrupt. An mb() is used to complete the clear/disable writes before the
interrupt is registered.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring these
bits have taken effect on the device is to perform a read back to force it
to make it all the way to the device. This is documented in device-io.rst
and a talk by Will Deacon on this can be seen over here:
Let's do that to ensure these bits hit the device. Because the mb()'s
purpose wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: 199ef13cac7d ("scsi: ufs: avoid spurious UFS host controller interrupts") Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-8-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, HCLKDIV is written to and then completed with an mb().
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: d90996dae8e4 ("scsi: ufs: Add UFS platform driver for Cadence UFS") Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-6-181252004586@redhat.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the CGC enable bit is written and then an mb() is used to ensure
that completes before continuing.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Fixes: 81c0fc51b7a7 ("ufs-qcom: add support for Qualcomm Technologies Inc platforms") Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-5-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the QUNIPRO_SEL bit is written to and then an mb() is used to
ensure that completes before continuing.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
But, there's really no reason to even ensure completion before
continuing. The only requirement here is that this write is ordered to this
endpoint (which readl()/writel() guarantees already). For that reason the
mb() can be dropped altogether without anything forcing completion.
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations") Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-4-181252004586@redhat.com Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On SM8550, depending on the Qunipro, we can run with G5 or G4. For now,
when the major version is 5 or above, we go with G5. Therefore, we need to
specifically tell UFS HC that.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 823150ecf04f ("scsi: ufs: qcom: Perform read back after writing unipro mode") Signed-off-by: Sasha Levin <sashal@kernel.org>
On newer UFS revisions, the register at offset 0xD0 is called,
REG_UFS_PARAM0. Since the existing register, RETRY_TIMER_REG is not used
anywhere, it is safe to use the new name.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com> Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 823150ecf04f ("scsi: ufs: qcom: Perform read back after writing unipro mode") Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently after writing to REG_UFS_SYS1CLK_1US a mb() is used to ensure
that write has gone through to the device.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations") Reviewed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-2-181252004586@redhat.com Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the reset bit for the UFS provided reset controller (used by its
phy) is written to, and then a mb() happens to try and ensure that hit the
device. Immediately afterwards a usleep_range() occurs.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
Let's do that to ensure the bit hits the device. By doing so and
guaranteeing the ordering against the immediately following usleep_range(),
the mb() can safely be removed.
Fixes: 81c0fc51b7a7 ("ufs-qcom: add support for Qualcomm Technologies Inc platforms") Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-1-181252004586@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct bpf_fib_lookup is supposed to be of size 64. A recent commit 59b418c7063d ("bpf: Add a check for struct bpf_fib_lookup size") added
a static assertion to check this property so that future changes to the
structure will not accidentally break this assumption.
As it immediately turned out, on some 32-bit arm systems, when AEABI=n,
the total size of the structure was equal to 68, see [1]. This happened
because the bpf_fib_lookup structure contains a union of two 16-bit
fields:
union {
__u16 tot_len;
__u16 mtu_result;
};
which was supposed to compile to a 16-bit-aligned 16-bit field. On the
aforementioned setups it was instead both aligned and padded to 32-bits.
Declare this inner union as __attribute__((packed, aligned(2))) such
that it always is of size 2 and is aligned to 16 bits.
clang complains that the temporary string for the name passed into
alloc_workqueue() is too short for its contents:
drivers/net/ethernet/qlogic/qed/qed_main.c:1218:3: error: 'snprintf' will always be truncated; specified size is 16, but format string expands to at least 18 [-Werror,-Wformat-truncation]
There is no need for a temporary buffer, and the actual name of a workqueue
is 32 bytes (WQ_NAME_LEN), so just use the interface as intended to avoid
the truncation.
root_domain::overutilized is only used for EAS(energy aware scheduler)
to decide whether to do load balance or not. It is not used if EAS
not possible.
Currently enqueue_task_fair and task_tick_fair accesses, sometime updates
this field. In update_sd_lb_stats it is updated often. This causes cache
contention due to true sharing and burns a lot of cycles. ::overload and
::overutilized are part of the same cacheline. Updating it often invalidates
the cacheline. That causes access to ::overload to slow down due to
false sharing. Hence add EAS check before accessing/updating this field.
EAS check is optimized at compile time or it is a static branch.
Hence it shouldn't cost much.
With the patch, both enqueue_task_fair and newidle_balance don't show
up as hot routines in perf profile.
aaa8736370db ("x86, relocs: Ignore relocations in .notes section")
... only started ignoring the .notes sections in print_absolute_relocs(),
but the same logic should also by applied in walk_relocs() to avoid
such relocations.
[ mingo: Fixed various typos in the changelog, removed extra curly braces from the code. ]
Currently host relies on CE interrupts to get notified that
the service ready message is ready. This results in timeout
issue if the interrupt is not fired, due to some unknown
reasons. See below logs:
[76321.937866] ath10k_pci 0000:02:00.0: wmi service ready event not received
...
[76322.016738] ath10k_pci 0000:02:00.0: Could not init core: -110
And finally it causes WLAN interface bring up failure.
Change to give it one more chance here by polling CE rings,
before failing directly.
md_do_sync
j = mddev->resync_min
while (j < max_sectors)
sectors = raid10_sync_request(mddev, j, &skipped)
if (!md_bitmap_start_sync(..., &sync_blocks))
// md_bitmap_start_sync set sync_blocks to 0
return sync_blocks + sectors_skippe;
// sectors = 0;
j += sectors;
// j never change
Root cause is that commit 301867b1c168 ("md/raid10: check
slab-out-of-bounds in md_bitmap_get_counter") return early from
md_bitmap_get_counter(), without setting returned blocks.
Fix this problem by always set returned blocks from
md_bitmap_get_counter"(), as it used to be.
Noted that this patch just fix the softlockup problem in kernel, the
case that bitmap size doesn't match array size still need to be fixed.
Fixes: 301867b1c168 ("md/raid10: check slab-out-of-bounds in md_bitmap_get_counter") Reported-and-tested-by: Nigel Croxon <ncroxon@redhat.com> Closes: https://lore.kernel.org/all/71ba5272-ab07-43ba-8232-d2da642acb4e@redhat.com/ Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20240422065824.2516-1-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For cmdq jump command, offset 0 means relative jump and offset 1
means absolute jump. cmdq_pkt_jump() is absolute jump, so fix the
typo of CMDQ_JUMP_RELATIVE in cmdq_pkt_jump().
Fixes: 946f1792d3d7 ("soc: mediatek: cmdq: add jump function") Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240222154120.16959-2-chunkuang.hu@kernel.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a check to make sure that the requested xattr node size is no larger
than the eraseblock minus the cleanmarker.
Unlike the usual inode nodes, the xattr nodes aren't split into parts
and spread across multiple eraseblocks, which means that a xattr node
must not occupy more than one eraseblock. If the requested xattr value is
too large, the xattr node can spill onto the next eraseblock, overwriting
the nodes and causing errors such as:
jffs2: argh. node added in wrong place at 0x0000b050(2)
jffs2: nextblock 0x0000a000, expected at 0000b00c
jffs2: error: (823) do_verify_xattr_datum: node CRC failed at 0x01e050,
read=0xfc892c93, calc=0x000000
jffs2: notice: (823) jffs2_get_inode_nodes: Node header CRC failed
at 0x01e00c. {848f,2fc4,0fef511f,59a3d171}
jffs2: Node at 0x0000000c with length 0x00001044 would run over the
end of the erase block
jffs2: Perhaps the file system was created with the wrong erase size?
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found
at 0x00000010: 0x1044 instead
This breaks the filesystem and can lead to KASAN crashes such as:
BUG: KASAN: slab-out-of-bounds in jffs2_sum_add_kvec+0x125e/0x15d0
Read of size 4 at addr ffff88802c31e914 by task repro/830
CPU: 0 PID: 830 Comm: repro Not tainted 6.9.0-rc3+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS Arch Linux 1.16.3-1-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xc4/0x620
? __virt_addr_valid+0x308/0x5b0
kasan_report+0xc1/0xf0
? jffs2_sum_add_kvec+0x125e/0x15d0
? jffs2_sum_add_kvec+0x125e/0x15d0
jffs2_sum_add_kvec+0x125e/0x15d0
jffs2_flash_direct_writev+0xa8/0xd0
jffs2_flash_writev+0x9c9/0xef0
? __x64_sys_setxattr+0xc4/0x160
? do_syscall_64+0x69/0x140
? entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: aa98d7cf59b5 ("[JFFS2][XATTR] XATTR support on JFFS2 (version. 5)") Signed-off-by: Ilya Denisyev <dev@elkcl.ru> Link: https://lore.kernel.org/r/20240412155357.237803-1-dev@elkcl.ru Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The subchannel-type field "st" of s390_cio_stsch and s390_cio_msch
tracepoints is incorrectly filled with the subchannel-enabled SCHIB
value "ena". Fix this by assigning the correct value.
Fixes: d1de8633d96a ("s390 cio: Rewrite trace point class s390_class_schib") Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since sha512_transform_rorx() uses ymm registers, execute vzeroupper
before returning from it. This is necessary to avoid reducing the
performance of SSE code.
Fixes: e01d69cb0195 ("crypto: sha512 - Optimized SHA512 x86_64 assembly routine using AVX instructions.") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since sha256_transform_rorx() uses ymm registers, execute vzeroupper
before returning from it. This is necessary to avoid reducing the
performance of SSE code.
Fixes: d34a460092d8 ("crypto: sha256 - Optimized sha256 x86_64 routine using AVX2's RORX instructions") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is not a useful configuration, and there is not much point in saving
a few bytes when only one of the two is enabled, so just remove all
these ifdef checks and rely on of_match_node() and acpi_match_device()
returning NULL when these subsystems are disabled.
__cmpxchg_u8() had been added (initially) for the sake of
drivers/phy/ti/phy-tusb1210.c; the thing is, that drivers is
modular, so we need an export
Fixes: b344d6a83d01 "parisc: add support for cmpxchg on u8 pointers" Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-14 points out that v_size is always smaller than a 64KB
page size if that is configured by the CPU architecture:
fs/nilfs2/ioctl.c:63:19: error: result of comparison of constant 65536 with expression of type '__u16' (aka 'unsigned short') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (argv->v_size > PAGE_SIZE)
~~~~~~~~~~~~ ^ ~~~~~~~~~
This is ok, so just shut up that warning with a cast.
The 'TAG 66 Packet Format' description is missing the cipher code and
checksum fields that are packed into the message packet. As a result,
the buffer allocated for the packet is 3 bytes too small and
write_tag_66_packet() will write up to 3 bytes past the end of the
buffer.
Fix this by increasing the size of the allocation so the whole packet
will always fit in the buffer.
This fixes the below kasan slab-out-of-bounds bug:
BUG: KASAN: slab-out-of-bounds in ecryptfs_generate_key_packet_set+0x7d6/0xde0
Write of size 1 at addr ffff88800afbb2a5 by task touch/181
The buffer used to transfer data over the mailbox interface is mapped
using the client's device. This is incorrect, as the device performing
the DMA transfer is the mailbox itself. Fix it by using the mailbox
controller device instead.
This requires including the mailbox_controller.h header to dereference
the mbox_chan and mbox_controller structures. The header is not meant to
be included by clients. This could be fixed by extending the client API
with a function to access the controller's device.
Fixes: 4e3d60656a72 ("ARM: bcm2835: Add the Raspberry Pi firmware driver") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Stefan Wahren <wahrenst@gmx.net> Tested-by: Ivan T. Ivanov <iivanov@suse.de> Link: https://lore.kernel.org/r/20240326195807.15163-3-laurent.pinchart@ideasonboard.com Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In spu2_dump_omd() value of ptr is increased by ciph_key_len
instead of hash_iv_len which could lead to going beyond the
buffer boundaries.
Fix this bug by changing ciph_key_len to hash_iv_len.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The original mount API conversion inexplicably left out the change
from ->remount_fs to ->reconfigure; do that now.
Fixes: 7ab2fa7693c3 ("vfs: Convert openpromfs to use the new mount API") Signed-off-by: Eric Sandeen <sandeen@redhat.com> Link: https://lore.kernel.org/r/90b968aa-c979-420f-ba37-5acc3391b28f@redhat.com Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
epoll can call out to vfs_poll() with a file pointer that may race with
the last 'fput()'. That would make f_count go down to zero, and while
the ep->mtx locking means that the resulting file pointer tear-down will
be blocked until the poll returns, it means that f_count is already
dead, and any use of it won't actually get a reference to the file any
more: it's dead regardless.
Make sure we have a valid ref on the file pointer before we call down to
vfs_poll() from the epoll routines.
On system where native nvme multipath is configured and iopolicy
is set to numa but the nvme controller numa node id is undefined
or -1 (NUMA_NO_NODE) then avoid calculating node distance for
finding optimal io path. In such case we may access numa distance
table with invalid index and that may potentially refer to incorrect
memory. So this patch ensures that if the nvme controller numa node
id is -1 then instead of calculating node distance for finding optimal
io path, we set the numa node distance of such controller to default 10
(LOCAL_DISTANCE).
... and I think that's actually the important thing here:
- the first page fault is from user space, and triggers the vsyscall
emulation.
- the second page fault is from __do_sys_gettimeofday(), and that should
just have caused the exception that then sets the return value to
-EFAULT
- the third nested page fault is due to _raw_spin_unlock_irqrestore() ->
preempt_schedule() -> trace_sched_switch(), which then causes a BPF
trace program to run, which does that bpf_probe_read_compat(), which
causes that page fault under pagefault_disable().
It's quite the nasty backtrace, and there's a lot going on.
The problem is literally the vsyscall emulation, which sets
current->thread.sig_on_uaccess_err = 1;
and that causes the fixup_exception() code to send the signal *despite* the
exception being caught.
And I think that is in fact completely bogus. It's completely bogus
exactly because it sends that signal even when it *shouldn't* be sent -
like for the BPF user mode trace gathering.
In other words, I think the whole "sig_on_uaccess_err" thing is entirely
broken, because it makes any nested page-faults do all the wrong things.
Now, arguably, I don't think anybody should enable vsyscall emulation any
more, but this test case clearly does.
I think we should just make the "send SIGSEGV" be something that the
vsyscall emulation does on its own, not this broken per-thread state for
something that isn't actually per thread.
The x86 page fault code actually tried to deal with the "incorrect nesting"
by having that:
if (in_interrupt())
return;
which ignores the sig_on_uaccess_err case when it happens in interrupts,
but as shown by this example, these nested page faults do not need to be
about interrupts at all.
IOW, I think the only right thing is to remove that horrendously broken
code.
The attached patch looks like the ObviouslyCorrect(tm) thing to do.
NOTE! This broken code goes back to this commit in 2011:
4fc3490114bb ("x86-64: Set siginfo and context on vsyscall emulation faults")
... and back then the reason was to get all the siginfo details right.
Honestly, I do not for a moment believe that it's worth getting the siginfo
details right here, but part of the commit says:
This fixes issues with UML when vsyscall=emulate.
... and so my patch to remove this garbage will probably break UML in this
situation.
I do not believe that anybody should be running with vsyscall=emulate in
2024 in the first place, much less if you are doing things like UML. But
let's see if somebody screams.
There is a race condition when re-creating a kfd_process for a process.
This has been observed when a process under the debugger executes
exec(3). In this scenario:
- The process executes exec.
- This will eventually release the process's mm, which will cause the
kfd_process object associated with the process to be freed
(kfd_process_free_notifier decrements the reference count to the
kfd_process to 0). This causes kfd_process_ref_release to enqueue
kfd_process_wq_release to the kfd_process_wq.
- The debugger receives the PTRACE_EVENT_EXEC notification, and tries to
re-enable AMDGPU traps (KFD_IOC_DBG_TRAP_ENABLE).
- When handling this request, KFD tries to re-create a kfd_process.
This eventually calls kfd_create_process and kobject_init_and_add.
At this point the call to kobject_init_and_add can fail because the
old kfd_process.kobj has not been freed yet by kfd_process_wq_release.
This patch proposes to avoid this race by making sure to drain
kfd_process_wq before creating a new kfd_process object. This way, we
know that any cleanup task is done executing when we reach
kobject_init_and_add.
Signed-off-by: Lancelot SIX <lancelot.six@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rcu quiescent state is reported in the rcu-read critical section, so
the lockdep warning is triggered.
Fix this by splitting out the inner working of __do_softirq() into a helper
function which takes an argument to distinguish between ksoftirqd task
context and interrupted context and invoke it from the relevant call sites
with the proper context information and use that for the conditional
invocation of rcu_softirq_qs().
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://msgid.link/r/20240410172615.255424-2-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The codec leaves tie combo jack's sleeve/ring2 to floating status
default. It would cause electric noise while connecting the active
speaker jack during boot or shutdown.
This patch requests a gpio to control the additional jack circuit
to tie the contacts to the ground or floating.
The regulator IRQ helper requires caller to provide pointer to IRQ name
which is kept in memory by caller. All other data passed to the helper
in the regulator_irq_desc structure is copied. This can cause some
confusion and unnecessary complexity.
Make the regulator_irq_helper() to copy also the provided IRQ name
information so caller can discard the name after the call to
regulator_irq_helper() completes.
Currently, the sud_test expects the emulated syscall to return the
emulated syscall number. This assumption only works on architectures
were the syscall calling convention use the same register for syscall
number/syscall return value. This is not the case for RISC-V and thus
the return value must be also emulated using the provided ucontext.
In snd_card_disconnect(), we set card->shutdown flag at the beginning,
call callbacks and do sync for card->power_ref_sleep waiters at the
end. The callback may delete a kctl element, and this can lead to a
deadlock when the device was in the suspended state. Namely:
* A process waits for the power up at snd_power_ref_and_wait() in
snd_ctl_info() or read/write() inside card->controls_rwsem.
* The system gets disconnected meanwhile, and the driver tries to
delete a kctl via snd_ctl_remove*(); it tries to take
card->controls_rwsem again, but this is already locked by the
above. Since the sleeper isn't woken up, this deadlocks.
An easy fix is to wake up sleepers before processing the driver
disconnect callbacks but right after setting the card->shutdown flag.
Then all sleepers will abort immediately, and the code flows again.
So, basically this patch moves the wait_event() call at the right
timing. While we're at it, just to be sure, call wait_event_all()
instead of wait_event(), although we don't use exclusive events on
this queue for now.
The commit 81033c6b584b ("ALSA: core: Warn on empty module")
introduced a WARN_ON() for a NULL module pointer passed at snd_card
object creation, and it also wraps the code around it with '#ifdef
MODULE'. This works in most cases, but the devils are always in
details. "MODULE" is defined when the target code (i.e. the sound
core) is built as a module; but this doesn't mean that the caller is
also built-in or not. Namely, when only the sound core is built-in
(CONFIG_SND=y) while the driver is a module (CONFIG_SND_USB_AUDIO=m),
the passed module pointer is ignored even if it's non-NULL, and
card->module remains as NULL. This would result in the missing module
reference up/down at the device open/close, leading to a race with the
code execution after the module removal.
For addressing the bug, move the assignment of card->module again out
of ifdef. The WARN_ON() is still wrapped with ifdef because the
module can be really NULL when all sound drivers are built-in.
Note that we keep 'ifdef MODULE' for WARN_ON(), otherwise it would
lead to a false-positive NULL module check. Admittedly it won't catch
perfectly, i.e. no check is performed when CONFIG_SND=y. But, it's no
real problem as it's only for debugging, and the condition is pretty
rare.
Fixes: 81033c6b584b ("ALSA: core: Warn on empty module") Reported-by: Xu Yang <xu.yang_2@nxp.com> Closes: https://lore.kernel.org/r/20240520170349.2417900-1-xu.yang_2@nxp.com Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Tested-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20240522070442.17786-1-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases when adding a cluster to the directory index,
they are placed at the end, and in the bitmap, this cluster corresponds
to the last bit. The new directory size is calculated as follows:
data_size = (u64)(bit + 1) << indx->index_bits;
In the case of reusing a non-final cluster from the index,
data_size is calculated incorrectly, resulting in the directory size
differing from the actual size.
A check for cluster reuse has been added, and the size update is skipped.
Fixes: 82cae269cfa95 ("fs/ntfs3: Add initialization of super block") Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When counting and checking hard links in an ntfs file record,
struct MFT_REC {
struct NTFS_RECORD_HEADER rhdr; // 'FILE'
__le16 seq; // 0x10: Sequence number for this record.
>> __le16 hard_links; // 0x12: The number of hard links to record.
__le16 attr_off; // 0x14: Offset to attributes.
...
the ntfs3 driver ignored short names (DOS names), causing the link count
to be reduced by 1 and messages to be output to dmesg.
For Windows, such a situation is a minor error, meaning chkdsk does not report
errors on such a volume, and in the case of using the /f switch, it silently
corrects them, reporting that no errors were found. This does not affect
the consistency of the file system.
Nevertheless, the behavior in the ntfs3 driver is incorrect and
changes the content of the file system. This patch should fix that.
PS: most likely, there has been a confusion of concepts
MFT_REC::hard_links and inode::__i_nlink.
Fixes: 82cae269cfa95 ("fs/ntfs3: Add initialization of super block") Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot has reported a potential hang in nilfs_detach_log_writer() called
during nilfs2 unmount.
Analysis revealed that this is because nilfs_segctor_sync(), which
synchronizes with the log writer thread, can be called after
nilfs_segctor_destroy() terminates that thread, as shown in the call trace
below:
Fix this issue by changing nilfs_segctor_sync() so that the log writer
thread returns normally without synchronizing after it terminates, and by
forcing tasks that are already waiting to complete once after the thread
terminates.
The skipped inode metadata flushout will then be processed together in the
subsequent cleanup work in nilfs_segctor_destroy().
A potential and reproducible race issue has been identified where
nilfs_segctor_sync() would block even after the log writer thread writes a
checkpoint, unless there is an interrupt or other trigger to resume log
writing.
This turned out to be because, depending on the execution timing of the
log writer thread running in parallel, the log writer thread may skip
responding to nilfs_segctor_sync(), which causes a call to schedule()
waiting for completion within nilfs_segctor_sync() to lose the opportunity
to wake up.
The reason why waking up the task waiting in nilfs_segctor_sync() may be
skipped is that updating the request generation issued using a shared
sequence counter and adding an wait queue entry to the request wait queue
to the log writer, are not done atomically. There is a possibility that
log writing and request completion notification by nilfs_segctor_wakeup()
may occur between the two operations, and in that case, the wait queue
entry is not yet visible to nilfs_segctor_wakeup() and the wake-up of
nilfs_segctor_sync() will be carried over until the next request occurs.
Fix this issue by performing these two operations simultaneously within
the lock section of sc_state_lock. Also, following the memory barrier
guidelines for event waiting loops, move the call to set_current_state()
in the same location into the event waiting loop to ensure that a memory
barrier is inserted just before the event condition determination.
Compiling the m68k kernel with support for the ColdFire CPU family fails
with the following error:
In file included from drivers/net/ethernet/smsc/smc91x.c:80:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_reset’:
drivers/net/ethernet/smsc/smc91x.h:160:40: error: implicit declaration of function ‘_swapw’; did you mean ‘swap’? [-Werror=implicit-function-declaration]
160 | #define SMC_outw(lp, v, a, r) writew(_swapw(v), (a) + (r))
| ^~~~~~
drivers/net/ethernet/smsc/smc91x.h:904:25: note: in expansion of macro ‘SMC_outw’
904 | SMC_outw(lp, x, ioaddr, BANK_SELECT); \
| ^~~~~~~~
drivers/net/ethernet/smsc/smc91x.c:250:9: note: in expansion of macro ‘SMC_SELECT_BANK’
250 | SMC_SELECT_BANK(lp, 2);
| ^~~~~~~~~~~~~~~
cc1: some warnings being treated as errors
The function _swapw() was removed in commit d97cf70af097 ("m68k: use
asm-generic/io.h for non-MMU io access functions"), but is still used in
drivers/net/ethernet/smsc/smc91x.h.
Use ioread16be() and iowrite16be() to resolve the error.
Cc: stable@vger.kernel.org Fixes: d97cf70af097 ("m68k: use asm-generic/io.h for non-MMU io access functions") Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240510113054.186648-2-thorsten.blum@toblux.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following -Wformat-security compile warnings adding missing
format arguments:
latency-collector.c: In function ‘show_available’:
latency-collector.c:938:17: warning: format not a string literal and
no format arguments [-Wformat-security]
938 | warnx(no_tracer_msg);
| ^~~~~
latency-collector.c:943:17: warning: format not a string literal and
no format arguments [-Wformat-security]
943 | warnx(no_latency_tr_msg);
| ^~~~~
latency-collector.c: In function ‘find_default_tracer’:
latency-collector.c:986:25: warning: format not a string literal and
no format arguments [-Wformat-security]
986 | errx(EXIT_FAILURE, no_tracer_msg);
|
^~~~
latency-collector.c: In function ‘scan_arguments’:
latency-collector.c:1881:33: warning: format not a string literal and
no format arguments [-Wformat-security]
1881 | errx(EXIT_FAILURE, no_tracer_msg);
| ^~~~
Link: https://lore.kernel.org/linux-trace-kernel/20240404011009.32945-1-skhan@linuxfoundation.org Cc: stable@vger.kernel.org Fixes: e23db805da2df ("tracing/tools: Add the latency-collector to tools directory") Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reader code in rb_get_reader_page() swaps a new reader page into the
ring buffer by doing cmpxchg on old->list.prev->next to point it to the
new page. Following that, if the operation is successful,
old->list.next->prev gets updated too. This means the underlying
doubly-linked list is temporarily inconsistent, page->prev->next or
page->next->prev might not be equal back to page for some page in the
ring buffer.
The resize operation in ring_buffer_resize() can be invoked in parallel.
It calls rb_check_pages() which can detect the described inconsistency
and stop further tracing:
Note that ring_buffer_resize() calls rb_check_pages() only if the parent
trace_buffer has recording disabled. Recent commit d78ab792705c
("tracing: Stop current tracer when resizing buffer") causes that it is
now always the case which makes it more likely to experience this issue.
The window to hit this race is nonetheless very small. To help
reproducing it, one can add a delay loop in rb_get_reader_page():
ret = rb_head_page_replace(reader, cpu_buffer->reader_page);
if (!ret)
goto spin;
for (unsigned i = 0; i < 1U << 26; i++) /* inserted delay loop */
__asm__ __volatile__ ("" : : : "memory");
rb_list_head(reader->list.next)->prev = &cpu_buffer->reader_page->list;
.. and then run the following commands on the target system:
echo 1 > /sys/kernel/tracing/events/sched/sched_switch/enable
while true; do
echo 16 > /sys/kernel/tracing/buffer_size_kb; sleep 0.1
echo 8 > /sys/kernel/tracing/buffer_size_kb; sleep 0.1
done &
while true; do
for i in /sys/kernel/tracing/per_cpu/*; do
timeout 0.1 cat $i/trace_pipe; sleep 0.2
done
done
To fix the problem, make sure ring_buffer_resize() doesn't invoke
rb_check_pages() concurrently with a reader operating on the same
ring_buffer_per_cpu by taking its cpu_buffer->reader_lock.
Link: https://lore.kernel.org/linux-trace-kernel/20240517134008.24529-3-petr.pavlu@suse.com Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 659f451ff213 ("ring-buffer: Add integrity check at end of iter read") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
[ Fixed whitespace ] Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An issue was found on the RTL8125b when transmitting small fragmented
packets, whereby invalid entries were inserted into the transmit ring
buffer, subsequently leading to calls to dma_unmap_single() with a null
address.
This was caused by rtl8169_start_xmit() not noticing changes to nr_frags
which may occur when small packets are padded (to work around hardware
quirks) in rtl8169_tso_csum_v2().
To fix this, postpone inspecting nr_frags until after any padding has been
applied.
Ken reported that RTL8125b can lock up if gro_flush_timeout has the
default value of 20000 and napi_defer_hard_irqs is set to 0.
In this scenario device interrupts aren't disabled, what seems to
trigger some silicon bug under heavy load. I was able to reproduce this
behavior on RTL8168h. Fix this by reverting 7274c4147afb.
Fixes: 7274c4147afb ("r8169: don't try to disable interrupts if NAPI is scheduled already") Cc: stable@vger.kernel.org Reported-by: Ken Milmore <ken.milmore@gmail.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/9b5b6f4c-4f54-4b90-b0b3-8d8023c2e780@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
The "buf" pointer is an array of u16 values. This code should be
using ARRAY_SIZE() (which is 256) instead of sizeof() (which is 512),
otherwise it can the still got out of bounds.
Fixes: c8d2f34ea96e ("speakup: Avoid crash on very long word") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Link: https://lore.kernel.org/r/d16f67d2-fd0a-4d45-adac-75ddd11001aa@moroto.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses either gsm0_receive() or gsm1_receive()
depending on whether the user configured the mux in basic or advanced
option mode. Both functions share some state values over the same logical
elements of the frame. However, both frame types differ in their nature.
gsm0_receive() uses non-transparency framing, whereas gsm1_receive() uses
transparency mechanism. Switching between both modes leaves the receive
function in an undefined state when done during frame reception.
Fix this by splitting both states. Add gsm0_receive_state_check_and_fix()
and gsm1_receive_state_check_and_fix() to ensure that gsm->state is reset
after a change of gsm->receive.
Note that gsm->state is only accessed in:
- gsm0_receive()
- gsm1_receive()
- gsm_error()
Assuming the following:
- side A configures the n_gsm in basic option mode
- side B sends the header of a basic option mode frame with data length 1
- side A switches to advanced option mode
- side B sends 2 data bytes which exceeds gsm->len
Reason: gsm->len is not used in advanced option mode.
- side A switches to basic option mode
- side B keeps sending until gsm0_receive() writes past gsm->buf
Reason: Neither gsm->state nor gsm->len have been reset after
reconfiguration.
Fix this by changing gsm->count to gsm->len comparison from equal to less
than. Also add upper limit checks against the constant MAX_MRU in
gsm0_receive() and gsm1_receive() to harden against memory corruption of
gsm->len and gsm->mru.
All other checks remain as we still need to limit the data according to the
user configuration and actual payload size.
When the BIOS configures the architectural TSC-adjust MSRs on secondary
sockets to correct a constant inter-chassis offset, after Linux brings the
cores online, the TSC sync check later resets the core-local MSR to 0,
triggering HPET fallback and leading to performance loss.
Fix this by unconditionally using the initial adjust values read from the
MSRs. Trusting the initial offsets in this architectural mechanism is a
better approach than special-casing workarounds for specific platforms.
kernel_include.py, whose origin is misc.py of docutils, uses reprunicode.
Upstream docutils removed the offending line from the corresponding file
(docutils/docutils/parsers/rst/directives/misc.py) in January 2022.
Quoting the changelog [3]:
Deprecate `nodes.reprunicode` and `nodes.ensure_str()`.
Drop uses of the deprecated constructs (not required with Python 3).
sched_core_share_pid() copies the cookie to userspace with
put_user(id, (u64 __user *)uaddr), expecting 64 bits of space.
The "unsigned long" datatype that is documented in core-scheduling.rst
however is only 32 bits large on 32 bit architectures.
Document "unsigned long long" as the correct data type that is always
64bits large.
This matches what the selftest cs_prctl_test.c has been doing all along.
When asn1_encode_sequence() fails, WARN is not the correct solution.
1. asn1_encode_sequence() is not an internal function (located
in lib/asn1_encode.c).
2. Location is known, which makes the stack trace useless.
3. Results a crash if panic_on_warn is set.
It is also noteworthy that the use of WARN is undocumented, and it
should be avoided unless there is a carefully considered rationale to
use it.
Replace WARN with pr_err, and print the return value instead, which is
only useful piece of information.
Cc: stable@vger.kernel.org # v5.13+ Fixes: f2219745250f ("security: keys: trusted: use ASN.1 TPM2 key format for the blobs") Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
