gpiolib has a corner case with open drain outputs that are emulated.
When such outputs are outputting a logic 1, emulation will set the
hardware to input mode, which will cause gpiod_get_direction() to
report that it is in input mode. This is different from the behaviour
with a true open-drain output.
Unify the semantics here.
Cc: <stable@vger.kernel.org> Suggested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cad6fade6e78 ("xtensa: clean up WSR*/RSR*/get_sr/set_sr") removed
{RSR,WSR}_CPENABLE from xtensa code, but did not fix up all users,
breaking gpio-xtensa driver build. Update gpio-xtensa to use
new xtensa_{get,set}_sr API.
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c40368 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c403683 ("libata: add extra internal command") Cc: stable@vger.kernel.org Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing export of ata_qc_get_active(), as per Pali.
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms") Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae241 ("ata: ahci_brcm: Recover from failures to identify devices") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f829794 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6bb86fefa086faba7b60bb452300b76a47cde1a5
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes. Upon closer analysis, it turns out that precise scalar
value tracking is missing a few precision markings for unknown scalars:
In the analysis of the second path coming after the successful exit above,
the path is being pruned at line 7. Pruning analysis found that both r0 are
precise P0 and both R1 are non-precise scalars and given prior path with
R1 as non-precise scalar succeeded, this one is therefore safe as well.
However, problem is that given condition at insn 7 in the first run, we only
followed goto and didn't push the other branch for later analysis, we've
never walked the few insns in there and therefore dead-code sanitation
rewrites it as goto pc-1, causing the hang depending on the skb address
hitting these conditions. The issue is that R1 should have been marked as
precise as well such that pruning enforces range check and conluded that new
R1 is not in range of old R1. In insn 4, we mark R1 (skb) as unknown scalar
via __mark_reg_unbounded() but not mark_reg_unbounded() and therefore
regs->precise remains as false.
Back in b5dc0163d8fd ("bpf: precise scalar_value tracking"), this was not
the case since marking out of __mark_reg_unbounded() had this covered as well.
Once in both are set as precise in 4 as they should have been, we conclude
that given R1 was in prior fall-through path 0x104c1500 and now is completely
unknown, the check at insn 7 concludes that we need to continue walking.
Analysis after the fix:
When starting writeback for a range that covers part of a preallocated
extent, due to a race with writeback for another range that also covers
another part of the same preallocated extent, we can end up in an infinite
loop.
Consider the following example where for inode 280 we have two dirty
ranges:
range A, from 294912 to 303103, 8192 bytes
range B, from 348160 to 438271, 90112 bytes
and we have the following file extent item layout for our inode:
leaf 38895616 gen 24544 total ptrs 29 free space 13820 owner 5
(...)
item 27 key (280 108 200704) itemoff 14598 itemsize 53
extent data disk bytenr 0 nr 0 type 1 (regular)
extent data offset 0 nr 94208 ram 94208
item 28 key (280 108 294912) itemoff 14545 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 2 (prealloc)
extent data offset 0 nr 81920 ram 81920
Then the following happens:
1) Writeback starts for range B (from 348160 to 438271), execution of
run_delalloc_nocow() starts;
2) The first iteration of run_delalloc_nocow()'s whil loop leaves us at
the extent item at slot 28, pointing to the prealloc extent item
covering the range from 294912 to 376831. This extent covers part of
our range;
3) An ordered extent is created against that extent, covering the file
range from 348160 to 376831 (28672 bytes);
4) We adjust 'cur_offset' to 376832 and move on to the next iteration of
the while loop;
5) The call to btrfs_lookup_file_extent() leaves us at the same leaf,
pointing to slot 29, 1 slot after the last item (the extent item
we processed in the previous iteration);
6) Because we are a slot beyond the last item, we call btrfs_next_leaf(),
which releases the search path before doing a another search for the
last key of the leaf (280 108 294912);
7) Right after btrfs_next_leaf() released the path, and before it did
another search for the last key of the leaf, writeback for the range
A (from 294912 to 303103) completes (it was previously started at
some point);
8) Upon completion of the ordered extent for range A, the prealloc extent
we previously found got split into two extent items, one covering the
range from 294912 to 303103 (8192 bytes), with a type of regular extent
(and no longer prealloc) and another covering the range from 303104 to
376831 (73728 bytes), with a type of prealloc and an offset of 8192
bytes. So our leaf now has the following layout:
leaf 38895616 gen 24544 total ptrs 31 free space 13664 owner 5
(...)
item 27 key (280 108 200704) itemoff 14598 itemsize 53
extent data disk bytenr 0 nr 0 type 1
extent data offset 0 nr 8192 ram 94208
item 28 key (280 108 208896) itemoff 14545 itemsize 53
extent data disk bytenr 10433142784 nr 86016 type 1
extent data offset 0 nr 86016 ram 86016
item 29 key (280 108 294912) itemoff 14492 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 1
extent data offset 0 nr 8192 ram 81920
item 30 key (280 108 303104) itemoff 14439 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 2
extent data offset 8192 nr 73728 ram 81920
9) After btrfs_next_leaf() returns, we have our path pointing to that same
leaf and at slot 30, since it has a key we didn't have before and it's
the first key greater then the key that was previously the last key of
the leaf (key (280 108 294912));
10) The extent item at slot 30 covers the range from 303104 to 376831
which is in our target range, so we process it, despite having already
created an ordered extent against this extent for the file range from
348160 to 376831. This is because we skip to the next extent item only
if its end is less than or equals to the start of our delalloc range,
and not less than or equals to the current offset ('cur_offset');
12) We then call create_io_em() for a 0 bytes range starting at offset
376832;
13) Then create_io_em() enters an infinite loop because its calls to
btrfs_drop_extent_cache() do nothing due to the 0 length range
passed to it. So no existing extent maps that cover the offset
376832 get removed, and therefore calls to add_extent_mapping()
return -EEXIST, resulting in an infinite loop. This loop from
create_io_em() is the following:
do {
btrfs_drop_extent_cache(BTRFS_I(inode), em->start,
em->start + em->len - 1, 0);
write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em, 1);
write_unlock(&em_tree->lock);
/*
* The caller has taken lock_extent(), who could race with us
* to add em?
*/
} while (ret == -EEXIST);
Also, each call to btrfs_drop_extent_cache() triggers a warning because
the start offset passed to it (376832) is smaller then the end offset
(376832 - 1) passed to it by -1, due to the 0 length:
Which results in flooding dmesg/syslog since btrfs_drop_extent_cache()
uses WARN_ON() and not WARN_ON_ONCE().
So fix this issue by changing run_delalloc_nocow()'s loop to move to the
next extent item when the current extent item ends at at offset less than
or equals to the current offset instead of the start offset.
Fixes: 80ff385665b7fc ("Btrfs: update nodatacow code v2") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that the JZ4725B displays the same buggy behaviour as the
JZ4740 that was described in commit f4c255f1a747 ("dmaengine: dma-jz4780:
Break descriptor chains on JZ4740").
Work around it by using the same workaround previously used for the
JZ4740.
Fixes commit f4c255f1a747 ("dmaengine: dma-jz4780: Break descriptor
chains on JZ4740")
dmaengine_desc_set_reuse() allocates a struct dma_slave_caps on the
stack, populates it using dma_get_slave_caps() and then accesses one
of its members.
However dma_get_slave_caps() may fail and this isn't accounted for,
leading to a legitimate warning of gcc-4.9 (but not newer versions):
In file included from drivers/spi/spi-bcm2835.c:19:0:
drivers/spi/spi-bcm2835.c: In function 'dmaengine_desc_set_reuse':
>> include/linux/dmaengine.h:1370:10: warning: 'caps.descriptor_reuse' is used uninitialized in this function [-Wuninitialized]
if (caps.descriptor_reuse) {
Fix it, thereby also silencing the gcc-4.9 warning.
The issue has been present for 4 years but surfaces only now that
the first caller of dmaengine_desc_set_reuse() has been added in
spi-bcm2835.c. Another user of reusable DMA descriptors has existed
for a while in pxa_camera.c, but it sets the DMA_CTRL_REUSE flag
directly instead of calling dmaengine_desc_set_reuse(). Nevertheless,
tag this commit for stable in case there are out-of-tree users.
This adds logic to the user_notification_basic test to set a member
of struct seccomp_notif to an invalid value to ensure that the kernel
returns EINVAL if any of the struct seccomp_notif members are set to
invalid values.
Signed-off-by: Sargun Dhillon <sargun@sargun.me> Suggested-by: Christian Brauner <christian.brauner@ubuntu.com> Link: https://lore.kernel.org/r/20191230203811.4996-1-sargun@sargun.me Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sizes by which seccomp_notif and seccomp_notif_resp are allocated are
based on the SECCOMP_GET_NOTIF_SIZES ioctl. This allows for graceful
extension of these datastructures. If userspace zeroes out the
datastructure based on its version, and it is lagging behind the kernel's
version, it will end up sending trailing garbage. On the other hand,
if it is ahead of the kernel version, it will write extra zero space,
and potentially cause corruption.
Signed-off-by: Sargun Dhillon <sargun@sargun.me> Suggested-by: Tycho Andersen <tycho@tycho.ws> Link: https://lore.kernel.org/r/20191230203503.4925-1-sargun@sargun.me Fixes: fec7b6690541 ("samples: add an example of seccomp user trap") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is a small change in enforcement of the uapi for
SECCOMP_IOCTL_NOTIF_RECV ioctl. Specifically, the datastructure which
is passed (seccomp_notif) must be zeroed out. Previously any of its
members could be set to nonsense values, and we would ignore it.
This ensures all fields are set to their zero value.
Signed-off-by: Sargun Dhillon <sargun@sargun.me> Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com> Reviewed-by: Aleksa Sarai <cyphar@cyphar.com> Acked-by: Tycho Andersen <tycho@tycho.ws> Link: https://lore.kernel.org/r/20191229062451.9467-2-sargun@sargun.me Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The seccomp_notif structure should be zeroed out prior to calling the
SECCOMP_IOCTL_NOTIF_RECV ioctl. Previously, the kernel did not check
whether these structures were zeroed out or not, so these worked.
This patch zeroes out the seccomp_notif data structure prior to calling
the ioctl.
Signed-off-by: Sargun Dhillon <sargun@sargun.me> Reviewed-by: Tycho Andersen <tycho@tycho.ws> Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com> Link: https://lore.kernel.org/r/20191229062451.9467-1-sargun@sargun.me Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that randconfig builds with gcc no longer produce a lot of
ccache hits, unlike with clang, and traced this back to plugins
now being enabled unconditionally if they are supported.
I am now working around this by adding
export CCACHE_COMPILERCHECK=/usr/bin/size -A %compiler%
to my top-level Makefile. This changes the heuristic that ccache uses
to determine whether the plugins are the same after a 'make clean'.
However, it also seems that being able to just turn off the plugins is
generally useful, at least for build testing it adds noticeable overhead
but does not find a lot of bugs additional bugs, and may be easier for
ccache users than my workaround.
The ram_core.c routines treat przs as circular buffers. When writing a
new crash dump, the old buffer needs to be cleared so that the new dump
doesn't end up in the wrong place (i.e. at the end).
The solution to this problem is to reset the circular buffer state before
writing a new Oops dump.
Because ocfs2_get_dlm_debug() function is called once less here, ocfs2
file system will trigger the system crash, usually after ocfs2 file
system is unmounted.
This system crash is caused by a generic memory corruption, these crash
backtraces are not always the same, for exapmle,
This regression problem was introduced by commit e581595ea29c ("ocfs: no
need to check return value of debugfs_create functions").
Link: http://lkml.kernel.org/r/20191225061501.13587-1-ghe@suse.com Fixes: e581595ea29c ("ocfs: no need to check return value of debugfs_create functions") Signed-off-by: Gang He <ghe@suse.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> [5.3+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pr_err() expects kB, but mm_pgtables_bytes() returns the number of bytes.
As everything else is printed in kB, I chose to fix the value rather than
the string.
Before:
[ pid ] uid tgid total_vm rss pgtables_bytes swapents oom_score_adj name
...
[ 1878] 1000 1878 217253 151144 1269760 0 0 python
...
Out of memory: Killed process 1878 (python) total-vm:869012kB, anon-rss:604572kB, file-rss:4kB, shmem-rss:0kB, UID:1000 pgtables:1269760kB oom_score_adj:0
After:
[ pid ] uid tgid total_vm rss pgtables_bytes swapents oom_score_adj name
...
[ 1436] 1000 1436 217253 151890 1294336 0 0 python
...
Out of memory: Killed process 1436 (python) total-vm:869012kB, anon-rss:607516kB, file-rss:44kB, shmem-rss:0kB, UID:1000 pgtables:1264kB oom_score_adj:0
Link: http://lkml.kernel.org/r/20191211202830.1600-1-idryomov@gmail.com Fixes: 70cb6d267790 ("mm/oom: add oom_score_adj and pgtables to Killed process message") Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Edward Chron <echron@arista.com> Cc: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because the status is not set if the page is already on the
target node, but move_pages() should return valid status as long as it
succeeds. The valid status may be errno or node id.
We can't simply initialize status array to zero since the pages may be
not on node 0. Fix it by updating status with node id which the page is
already on.
Link: http://lkml.kernel.org/r/1575584353-125392-1-git-send-email-yang.shi@linux.alibaba.com Fixes: a49bd4d71637 ("mm, numa: rework do_pages_move") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Reported-by: Felix Abecassis <fabecassis@nvidia.com> Tested-by: Felix Abecassis <fabecassis@nvidia.com> Suggested-by: Michal Hocko <mhocko@suse.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Acked-by: Christoph Lameter <cl@linux.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> [4.17+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cred_jar kmem_cache is already memcg accounted in the current kernel
but cred->security is not. Account cred->security to kmemcg.
Recently we saw high root slab usage on our production and on further
inspection, we found a buggy application leaking processes. Though that
buggy application was contained within its memcg but we observe much
more system memory overhead, couple of GiBs, during that period. This
overhead can adversely impact the isolation on the system.
One source of high overhead we found was cred->security objects, which
have a lifetime of at least the life of the process which allocated
them.
Link: http://lkml.kernel.org/r/20191205223721.40034-1-shakeelb@google.com Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Chris Down <chris@chrisdown.name> Reviewed-by: Roman Gushchin <guro@fb.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When zspage is migrated to the other zone, the zone page state should be
updated as well, otherwise the NR_ZSPAGE for each zone shows wrong
counts including proc/zoneinfo in practice.
Link: http://lkml.kernel.org/r/1575434841-48009-1-git-send-email-chanho.min@lge.com Fixes: 91537fee0013 ("mm: add NR_ZSMALLOC to vmstat") Signed-off-by: Chanho Min <chanho.min@lge.com> Signed-off-by: Jinsuk Choi <jjinsuk.choi@lge.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> [4.9+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently try to shrink a single zone when removing memory. We use
the zone of the first page of the memory we are removing. If that
memmap was never initialized (e.g., memory was never onlined), we will
read garbage and can trigger kernel BUGs (due to a stale pointer):
Instead, shrink the zones when offlining memory or when onlining failed.
Introduce and use remove_pfn_range_from_zone(() for that. We now
properly shrink the zones, even if we have DIMMs whereby
- Some memory blocks fall into no zone (never onlined)
- Some memory blocks fall into multiple zones (offlined+re-onlined)
- Multiple memory blocks that fall into different zones
Drop the zone parameter (with a potential dubious value) from
__remove_pages() and __remove_section().
Link: http://lkml.kernel.org/r/20191006085646.5768-6-david@redhat.com Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b319] Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: Michal Hocko <mhocko@suse.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: <stable@vger.kernel.org> [5.0+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently wait_event_interruptible_timeout is called in cec_thread_func()
when adap->transmitting is set. But if the adapter is unconfigured
while transmitting, then adap->transmitting is set to NULL. But the
hardware is still actually transmitting the message, and that's
indicated by adap->transmit_in_progress and we should wait until that
is finished or times out before transmitting new messages.
As the original commit says: adap->transmitting is the userspace view,
adap->transmit_in_progress reflects the hardware state.
However, if adap->transmitting is NULL and adap->transmit_in_progress
is true, then wait_event_interruptible is called (no timeout), which
can get stuck indefinitely if the CEC driver is flaky and never marks
the transmit-in-progress as 'done'.
So test against transmit_in_progress when deciding whether to use
the timeout variant or not, instead of testing against adap->transmitting.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 32804fcb612b ("media: cec: keep track of outstanding transmits") Cc: <stable@vger.kernel.org> # for v4.19 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARN if transmit_queue_sz is 0 but do not decrement it.
The CEC adapter will become unresponsive if it goes below
0 since then it thinks there are 4 billion messages in the
queue.
Obviously this should not happen, but a driver bug could
cause this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.12 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some messages are allowed to be a broadcast message in CEC 2.0
only, and should be ignored by CEC 1.4 devices.
Unfortunately, the check was wrong, causing such messages to be
marked as invalid under CEC 2.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.10 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The periodic PING command could interfere with the result of
a CEC transmit, causing a lost cec_transmit_attempt_done()
call.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.10 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declaring __current_thread_info as a global register variable has the
effect of preventing GCC from saving & restoring its value in cases
where the ABI would typically do so.
To quote GCC documentation:
> If the register is a call-saved register, call ABI is affected: the
> register will not be restored in function epilogue sequences after the
> variable has been assigned. Therefore, functions cannot safely return
> to callers that assume standard ABI.
When our position independent VDSO is built for the n32 or n64 ABIs all
functions it exposes should be preserving the value of $gp/$28 for their
caller, but in the presence of the __current_thread_info global register
variable GCC stops doing so & simply clobbers $gp/$28 when calculating
the address of the GOT.
In cases where the VDSO returns success this problem will typically be
masked by the caller in libc returning & restoring $gp/$28 itself, but
that is by no means guaranteed. In cases where the VDSO returns an error
libc will typically contain a fallback path which will now fail
(typically with a bad memory access) if it attempts anything which
relies upon the value of $gp/$28 - eg. accessing anything via the GOT.
One fix for this would be to move the declaration of
__current_thread_info inside the current_thread_info() function,
demoting it from global register variable to local register variable &
avoiding inadvertently creating a non-standard calling ABI for the VDSO.
Unfortunately this causes issues for clang, which doesn't support local
register variables as pointed out by commit fe92da0f355e ("MIPS: Changed
current_thread_info() to an equivalent supported by both clang and GCC")
which introduced the global register variable before we had a VDSO to
worry about.
Instead, fix this by continuing to use the global register variable for
the kernel proper but declare __current_thread_info as a simple extern
variable when building the VDSO. It should never be referenced, and will
cause a link error if it is. This resolves the calling convention issue
for the VDSO without having any impact upon the build of the kernel
itself for either clang or gcc.
Signed-off-by: Paul Burton <paulburton@kernel.org> Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Reported-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Christian Brauner <christian.brauner@canonical.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: <stable@vger.kernel.org> # v4.4+ Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is completely wrong to check for compile-time MIPS ISA revision in
the body of bpf_int_jit_compile() as it may lead to get MIPS JIT fully
omitted by the CC while the rest system will think that the JIT is
actually present and works [1].
We can check if the selected CPU really supports MIPS eBPF JIT at
configure time and avoid such situations when kernel can be built
without both JIT and interpreter, but with CONFIG_BPF_SYSCALL=y.
Commit 716850ab104d ("MIPS: eBPF: Initial eBPF support for MIPS32
architecture.") enabled our eBPF JIT for MIPS32 kernels, whereas it has
previously only been availailable for MIPS64. It was my understanding at
the time that the BPF test suite was passing & JITing a comparable
number of tests to our cBPF JIT [1], but it turns out that was not the
case.
The eBPF JIT has a number of problems on MIPS32:
- Most notably various code paths still result in emission of MIPS64
instructions which will cause reserved instruction exceptions & kernel
panics when run on MIPS32 CPUs.
- The eBPF JIT doesn't account for differences between the O32 ABI used
by MIPS32 kernels versus the N64 ABI used by MIPS64 kernels. Notably
arguments beyond the first 4 are passed on the stack in O32, and this
is entirely unhandled when JITing a BPF_CALL instruction. Stack space
must be reserved for arguments even if they all fit in registers, and
the callee is free to assume that stack space has been reserved for
its use - with the eBPF JIT this is not the case, so calling any
function can result in clobbering values on the stack & unpredictable
behaviour. Function arguments in eBPF are always 64-bit values which
is also entirely unhandled - the JIT still uses a single (32-bit)
register per argument. As a result all function arguments are always
passed incorrectly when JITing a BPF_CALL instruction, leading to
kernel crashes or strange behavior.
- The JIT attempts to bail our on use of ALU64 instructions or 64-bit
memory access instructions. The code doing this at the start of
build_one_insn() incorrectly checks whether BPF_OP() equals BPF_DW,
when it should really be checking BPF_SIZE() & only doing so when
BPF_CLASS() is one of BPF_{LD,LDX,ST,STX}. This results in false
positives that cause more bailouts than intended, and that in turns
hides some of the problems described above.
- The kernel's cBPF->eBPF translation makes heavy use of 64-bit eBPF
instructions that the MIPS32 eBPF JIT bails out on, leading to most
cBPF programs not being JITed at all.
Until these problems are resolved, revert the enabling of the eBPF JIT
on MIPS32 done by commit 716850ab104d ("MIPS: eBPF: Initial eBPF support
for MIPS32 architecture.").
Note that this does not undo the changes made to the eBPF JIT by that
commit, since they are a useful starting point to providing MIPS32
support - they're just not nearly complete.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This table is used for lots of things, add it's own lock.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/900 Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the HDMI unbinds drm_connector_cleanup() and drm_encoder_cleanup()
are called. This also happens when the connector and the encoder are
destroyed. This double call triggers a NULL pointer exception.
The patch fixes this by removing the cleanup calls in the unbind
function.
Klaus Ethgen reported occasional high CPU usages in his system that
seem caused by HD-audio driver. The perf output revealed that it's
in the unsolicited event handling in the workqueue, and the problem
seems triggered by some communication stall between the controller and
the codec at the runtime or system resume.
Actually a similar phenomenon was seen in the past for other Intel
platforms, and we already applied the workaround to enforce sync-write
for CORB/RIRB verbs for Skylake and newer chipsets (commit 2756d9143aa5 "ALSA: hda - Fix intermittent CORB/RIRB stall on Intel
chips"). Fortunately, the same workaround is applicable to the old
chipset, and the experiment showed the positive effect.
Based on the experiment result, this patch enables the sync-write
workaround for all Intel chipsets. The only reason I hesitated to
apply this workaround was about the possibly slightly higher CPU usage.
But if the lack of sync causes a much severer problem even for quite
old chip, we should think this would be necessary for all Intel chips.
Recently we found the headset-mic on the Dell Dock WD19 doesn't work
anymore after s3 (s2i or deep), this problem could be workarounded by
closing (pcm_close) the app and then reopening (pcm_open) the app, so
this bug is not easy to be detected by users.
When problem happens, retire_capture_urb() could still be called
periodically, but the size of captured data is always 0, it could be
a firmware bug on the dock. Anyway I found after resuming, the
snd_usb_pcm_prepare() will be called, and if we forcibly run
set_format() to set the interface and its endpoint, the capture
size will be normal again. This problem and workaound also apply to
playback.
To fix it in the kernel, add a quirk to let set_format() run
forcibly once after resume.
Make sure to check the return value of usb_altnum_to_altsetting() to
avoid dereferencing a NULL pointer when the requested alternate settings
is missing.
The format altsetting number may come from a quirk table and there does
not seem to be any other validation of it (the corresponding index is
checked however).
Jia-Ju Bai reported a possible sleep-in-atomic scenario in the ice1724
driver with Infrasonic Quartet support code: namely, ice->set_rate
callback gets called inside ice->reg_lock spinlock, while the callback
in quartet.c holds ice->gpio_mutex.
This patch fixes the invalid call: it simply moves the calls of
ice->set_rate and ice->set_mclk callbacks outside the spinlock.
To fix this, do what we do for cache read faults already: drop the
mmap_sem before calling into anything IO bound, in this case the
balance_dirty_pages() function, and return VM_FAULT_RETRY.
Link: http://lkml.kernel.org/r/20190924194238.GA29030@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some filesystem, such as vfat, may send bio which crosses device boundary,
and the worse thing is that the IO request starting within device boundaries
can contain more than one segment past EOD.
Commit dce30ca9e3b6 ("fs: fix guard_bio_eod to check for real EOD errors")
tries to fix this issue by returning -EIO for this situation. However,
this way lets fs user code lose chance to handle -EIO, then sync_inodes_sb()
may hang for ever.
Also the current truncating on last segment is dangerous by updating the
last bvec, given bvec table becomes not immutable any more, and fs bio
users may not retrieve the truncated pages via bio_for_each_segment_all() in
its .end_io callback.
Fixes this issue by supporting multi-segment truncating. And the
approach is simpler:
- just update bio size since block layer can make correct bvec with
the updated bio size. Then bvec table becomes really immutable.
- zero all truncated segments for read bio
Cc: Carlos Maiolino <cmaiolino@redhat.com> Cc: linux-fsdevel@vger.kernel.org Fixed-by: dce30ca9e3b6 ("fs: fix guard_bio_eod to check for real EOD errors") Reported-by: syzbot+2b9e54155c8c25d8d165@syzkaller.appspotmail.com Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
On Big Endian architectures, u16 port value was extracted from the wrong
parts of u32 sreg_port, just like commit 10596608c4d62 ("netfilter:
nf_tables: fix mismatch in big-endian system") describes.
We made the error message for the CORB/RIRB communication clearer by
upgrading to dev_WARN() so that user can notice better. But this
struck us like a boomerang: now it caught syzbot and reported back as
a fatal issue although it's not really any too serious bug that worth
for stopping the whole system.
OK, OK, let's be softy, downgrade it to the standard dev_err() again.
Fixes: dd65f7e19c69 ("ALSA: hda - Show the fatal CORB/RIRB error more clearly") Reported-by: syzbot+b3028ac3933f5c466389@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20191216151224.30013-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When assiging and testing taskstats in taskstats_exit() there's a race
when setting up and reading sig->stats when a thread-group with more
than one thread exits:
write to 0xffff8881157bbe10 of 8 bytes by task 7951 on cpu 0:
taskstats_tgid_alloc kernel/taskstats.c:567 [inline]
taskstats_exit+0x6b7/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
get_signal+0x2a2/0x1320 kernel/signal.c:2734
do_signal+0x3b/0xc00 arch/x86/kernel/signal.c:815
exit_to_usermode_loop+0x250/0x2c0 arch/x86/entry/common.c:159
prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
do_syscall_64+0x2d7/0x2f0 arch/x86/entry/common.c:299
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8881157bbe10 of 8 bytes by task 7949 on cpu 1:
taskstats_tgid_alloc kernel/taskstats.c:559 [inline]
taskstats_exit+0xb2/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
__do_sys_exit_group kernel/exit.c:994 [inline]
__se_sys_exit_group kernel/exit.c:992 [inline]
__x64_sys_exit_group+0x2e/0x30 kernel/exit.c:992
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by using smp_load_acquire() and smp_store_release().
Reported-by: syzbot+c5d03165a1bd1dead0c1@syzkaller.appspotmail.com Fixes: 34ec12349c8a ("taskstats: cleanup ->signal->stats allocation") Cc: stable@vger.kernel.org Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Acked-by: Marco Elver <elver@google.com> Reviewed-by: Will Deacon <will@kernel.org> Reviewed-by: Andrea Parri <parri.andrea@gmail.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Link: https://lore.kernel.org/r/20191009114809.8643-1-christian.brauner@ubuntu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
BUG: KASAN: use-after-free in perf_trace_lock_acquire+0x401/0x530 include/trace/events/lock.h:13
Read of size 8 at addr ffff8880a5cf2c50 by task syz-executor.0/26173
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7275 Comm: sshd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: b75eba76d3d7 ("tcp: send in-queue bytes in cmsg upon read") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The auto-parser assigns the bass speaker to DAC3 (NID 0x06) which
is without the volume control. I do not see a reason to use DAC2,
because the shared output to all speakers produces the sufficient
and well balanced sound. The stereo support is enough for this
purpose (laptop).
Nvidia proprietary driver doesn't support runtime power management, so
when a user only wants to use the integrated GPU, it's a common practice
to let dGPU not to bind any driver, and let its upstream port to be
runtime suspended. At the end of runtime suspension the port uses
platform power management to disable power through _OFF method of power
resource, which is listed by _PR3.
After commit b516ea586d71 ("PCI: Enable NVIDIA HDA controllers"), when
the dGPU comes with an HDA function, the HDA won't be suspended if the
dGPU is unbound, so the power resource can't be turned off by its
upstream port driver.
Commit 37a3a98ef601 ("ALSA: hda - Enable runtime PM only for
discrete GPU") only allows HDA to be runtime suspended once GPU is
bound, to keep APU's HDA working.
However, HDA on dGPU isn't that useful if dGPU is not bound to any
driver. So let's relax the runtime suspend requirement for dGPU's HDA
function, to disable the power source to save lots of power.
ASUS reported that there's an bass speaker in addition to internal
speaker and it uses DAC 0x02. It was not enabled in the commit 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS
UX431FLC") which only enables the amplifier and the front speaker.
This commit enables the bass speaker on top of the aforementioned
work to improve the acoustic experience.
Fixes: 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS UX431FLC") Signed-off-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191230031118.95076-1-chiu@endlessm.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When looking for a bit by number we make use of the cached result from the
preceding lookup to speed up operation. Firstly we check if the requested
pfn is within the cached zone and if not lookup the new zone. We then
check if the offset for that pfn falls within the existing cached node.
This happens regardless of whether the node is within the zone we are
now scanning. With certain memory layouts it is possible for this to
false trigger creating a temporary alias for the pfn to a different bit.
This leads the hibernation code to free memory which it was never allocated
with the expected fallout.
Ensure the zone we are scanning matches the cached zone before considering
the cached node.
Deep thanks go to Andrea for many, many, many hours of hacking and testing
that went into cornering this bug.
Reported-by: Andrea Righi <andrea.righi@canonical.com> Tested-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_XEN_BALLOON_MEMORY_HOTPLUG is not defined
reserve_additional_memory() will set balloon_stats.target_pages to a
wrong value in case there are still some ballooned pages allocated via
alloc_xenballooned_pages().
This will result in balloon_process() no longer be triggered when
ballooned pages are freed in batches.
Reported-by: Nicholas Tsirakis <niko.tsirakis@gmail.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Objects allocated by xen_blkif_alloc come from the 'blkif_cache' kmem
cache. This cache is destoyed when xen-blkif is unloaded so it is
necessary to wait for the deferred free routine used for such objects to
complete. This necessity was missed in commit 14855954f636 "xen-blkback:
allow module to be cleanly unloaded". This patch fixes the problem by
taking/releasing extra module references in xen_blkif_alloc/free()
respectively.
Signed-off-by: Paul Durrant <pdurrant@amazon.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some QPs (e.g. XRC QP) are not tracked in kernel, in this case they have
an invalid res and should not be bound to any dynamically-allocated
counter in auto mode.
The s390 CPU Measurement sampling facility has an overflow condition
which fires when all entries in a SBD are used.
The measurement alert interrupt is triggered and reads out all samples
in this SDB. It then tests the successor SDB, if this SBD is not full,
the interrupt handler does not read any samples at all from this SDB
The design waits for the hardware to fill this SBD and then trigger
another meassurement alert interrupt.
This scheme works nicely until
an perf_event_overflow() function call discards the sample due to
a too high sampling rate.
The interrupt handler has logic to read out a partially filled SDB
when the perf event overflow condition in linux common code is met.
This causes the CPUM sampling measurement hardware and the PMU
device driver to operate on the same SBD's trailer entry.
This should not happen.
This can be seen here using this trace:
cpumsf_pmu_add: tear:0xb5286000
hw_perf_event_update: sdbt 0xb5286000 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 1. interrupt
hw_perf_event_update: sdbt 0xb5286008 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 2. interrupt
... this goes on fine until...
hw_perf_event_update: sdbt 0xb5286068 full 1 over 0 flush_all:0
perf_push_sample1: overflow
one or more samples read from the IRQ handler are rejected by
perf_event_overflow() and the IRQ handler advances to the next SDB
and modifies the trailer entry of a partially filled SDB.
hw_perf_event_update: sdbt 0xb5286070 full 0 over 0 flush_all:1
timestamp: 14:32:52.519953
Next time the IRQ handler is called for this SDB the trailer entry shows
an overflow count of 19 missed entries.
hw_perf_event_update: sdbt 0xb5286070 full 1 over 19 flush_all:1
timestamp: 14:32:52.970058
Remove access to a follow on SDB when event overflow happened.
Function perf_event_ever_overflow() and perf_event_account_interrupt()
are called every time samples are processed by the interrupt handler.
However function perf_event_account_interrupt() has checks to avoid being
flooded with interrupts (more then 1000 samples are received per
task_tick). Samples are then dropped and a PERF_RECORD_THROTTLED is
added to the perf data. The perf subsystem limit calculation is:
maximum sample frequency := 100000 --> 1 samples per 10 us
task_tick = 10ms = 10000us --> 1000 samples per task_tick
The work flow is
measurement_alert() uses SDBT head and each SBDT points to 511
SDB pages, each with 126 sample entries. After processing 8 SBDs
and for each valid sample calling:
there is a considerable amount of samples being dropped, especially when
the sample frequency is very high and near the 100000 limit.
To avoid the high amount of samples being dropped near the end of a
task_tick time frame, increment the sampling interval in case of
dropped events. The CPU Measurement sampling facility on the s390
supports only intervals, specifiing how many CPU cycles have to be
executed before a sample is generated. Increase the interval when the
samples being generated hit the task_tick limit.
With commit 6ce220dd2f8ea71d6afc29b9a7524c12e39f374a ("raid5: don't set
STRIPE_HANDLE to stripe which is in batch list"), we don't want to set
STRIPE_HANDLE flag for sh which is already in batch list.
However, the stripe which is the head of batch list should set this flag,
otherwise panic could happen inside init_stripe at BUG_ON(sh->batch_head),
it is reproducible with raid5 on top of nvdimm devices per Xiao oberserved.
Thanks for Xiao's effort to verify the change.
Fixes: 6ce220dd2f8ea ("raid5: don't set STRIPE_HANDLE to stripe which is in batch list") Reported-by: Xiao Ni <xni@redhat.com> Tested-by: Xiao Ni <xni@redhat.com> Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the lookup method on the dynamic root directory such that creation
calls, such as mkdir, open(O_CREAT), symlink, etc. fail with EOPNOTSUPP
rather than failing with some odd error (such as EEXIST).
lookup() itself tries to create automount directories when it is invoked.
These are cached locally in RAM and not committed to storage.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each AFS mountpoint has strings that define the target to be mounted. This
is required to end in a dot that is supposed to be stripped off. The
string can include suffixes of ".readonly" or ".backup" - which are
supposed to come before the terminal dot. To add to the confusion, the "fs
lsmount" afs utility does not show the terminal dot when displaying the
string.
The kernel mount source string parser, however, assumes that the terminal
dot marks the suffix and that the suffix is always "" and is thus ignored.
In most cases, there is no suffix and this is not a problem - but if there
is a suffix, it is lost and this affects the ability to mount the correct
volume.
The command line mount command, on the other hand, is expected not to
include a terminal dot - so the problem doesn't arise there.
Fix this by making sure that the dot exists and then stripping it when
passing the string to the mount configuration.
Fixes: bec5eb614130 ("AFS: Implement an autocell mount capability [ver #2]") Reported-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The socket read/write helpers only look at the file O_NONBLOCK. not
the iocb IOCB_NOWAIT flag. This breaks users like preadv2/pwritev2
and io_uring that rely on not having the file itself marked nonblocking,
but rather the iocb itself.
Cc: netdev@vger.kernel.org Acked-by: David Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Gadget driver should always use config_ep_by_speed() to initialize
usb_ep struct according to usb device's operating speed. Otherwise,
usb_ep struct may be wrong if usb devcie's operating speed is changed.
The key point in this patch is that we want to make sure the desc pointer
in usb_ep struct will be set to NULL when gadget is disconnected.
This will force it to call config_ep_by_speed() to correctly initialize
usb_ep struct based on the new operating speed when gadget is
re-connected later.
Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: EJ Hsu <ejh@nvidia.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Under certain circumstances, encoder atomic_check() can be entered
without adjusted_mode having been reset to the same as mode, which
confuses the scaling logic and can lead to a misprogrammed display.
Fix this by checking against the user-provided mode directly.
We do not support atomic modesetting on pre-nv50 hardware, but until now
our connector code was setting drm_connector->state on pre-nv50 hardware.
This causes the core to enter atomic modesetting paths in at least:
1. drm_connector_get_encoder(), returning connector->state->best_encoder
which is always 0, causing us to always report 0 as encoder_id in
the drmModeConnector struct returned by drmModeGetConnector().
2. drm_encoder_get_crtc(), returning NULL because uses_atomic get set,
causing us to always report 0 as crtc_id in the drmModeEncoder struct
returned by drmModeGetEncoder()
Which in turn confuses userspace, at least plymouth thinks that the pipe
has changed because of this and tries to reconfigure it unnecessarily.
More in general we should not set drm_connector->state in the non-atomic
code as this violates the drm-core's expectations.
This commit fixes this by using a nouveau_conn_atom struct embedded in the
nouveau_connector struct for property handling in the non-atomic case.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1706557 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Place the declaration of struct nouveau_conn_atom above that of
struct nouveau_connector. This commit makes no changes to the moved
block what so ever, it just moves it up a bit.
This is a preparation patch to fix some issues with connector handling
on pre nv50 displays (which do not use atomic modesetting).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In iscsi_if_rx func, after receiving one request through
iscsi_if_recv_msg func, iscsi_if_send_reply will be called to try to
reply to the request in a do-while loop. If the iscsi_if_send_reply
function keeps returning -EAGAIN, a deadlock will occur.
For example, a client only send msg without calling recvmsg func, then
it will result in the watchdog soft lockup. The details are given as
follows:
The discovering of sas port is driven by workqueue in libsas. When libsas
is processing port events or phy events in workqueue, new events may rise
up and change the state of some structures such as asd_sas_phy. This may
cause some problems such as follows:
==>thread 1 ==>thread 2
==>phy up
==>phy_up_v3_hw()
==>oob_mode = SATA_OOB_MODE;
==>phy down quickly
==>hisi_sas_phy_down()
==>sas_ha->notify_phy_event()
==>sas_phy_disconnected()
==>oob_mode = OOB_NOT_CONNECTED
==>workqueue wakeup
==>sas_form_port()
==>sas_discover_domain()
==>sas_get_port_device()
==>oob_mode is OOB_NOT_CONNECTED and device
is wrongly taken as expander
This at last lead to the panic when libsas trying to issue a command to
discover the device.
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Link: https://lore.kernel.org/r/20191206011118.46909-1-yanaijie@huawei.com Reported-by: Gao Chuan <gaochuan4@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
PORT UPDATE asynchronous event is generated on the host that issues PLOGI
ELS (in the case of higher WWPN). In that case, the event shouldn't be
handled as it sets unwanted DPC flags (i.e. LOOP_RESYNC_NEEDED) that
trigger link flap.
Ignore the event if the host has higher WWPN, but handle otherwise.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-13-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qla2x00_configure_local_loop sets RELOGIN_NEEDED bit and calls
qla24xx_fcport_handle_login to perform the login. This bit triggers a wake
up of DPC later after a successful login.
The deferred call is not needed if login succeeds, and it's set in
qla24xx_fcport_handle_login in case of errors, hence it should be safe to
drop.
Link: https://lore.kernel.org/r/20191125165702.1013-12-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Acked-by: Quinn Tran <qutran@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qlt_handle_login schedules session for deletion even if a login is in
progress. That causes login bouncing, i.e. a few logins are made before it
settles down.
Complete the first login by sending Notify Acknowledge IOCB via
qlt_plogi_ack_unref if the session is pending login completion.
Fixes: 9cd883f07a54 ("scsi: qla2xxx: Fix session cleanup for N2N") Cc: Krishna Kant <krishna.kant@purestorage.com> Cc: Alexei Potashnik <alexei@purestorage.com> Link: https://lore.kernel.org/r/20191125165702.1013-11-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad099074 ("scsi: qla2xxx: Fix N2N link re-connect") Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The size of the buffer is hardcoded as 0x70 or 112 bytes, while the size of
ELS IOCB is 0x40 and the size of PLOGI payload returned by Get Parameters
command is 0x74.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-9-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
MBA_PORT_UPDATE generates duplicate log lines in target mode because
qlt_async_event is called twice. Drop the calls within the case as the
function will be called right after the switch statement.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-8-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvel.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
del_work is already initialized inside qla2x00_alloc_fcport, there's no
need to overwrite it. Indeed, it might prevent complete traversal of
workqueue list.
Fixes: a01c77d2cbc45 ("scsi: qla2xxx: Move session delete to driver work queue") Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-5-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Target makes implicit LOGO on session teardown. LOGO ELS is not send on the
wire and initiator is not aware that target no longer wants talking to
it. Initiator keeps sending I/O requests, target responds with BA_RJT, they
time out and then initiator sends ABORT TASK (ABTS-LS).
Current behaviour incurs unneeded I/O timeout and can be fixed for some
initiators by making explicit LOGO on session deletion.
Link: https://lore.kernel.org/r/20191125165702.1013-3-r.bolshakov@yadro.com Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If RoCE PDUs being sent or received contain pad bytes, then the iCRC
is miscalculated, resulting in PDUs being emitted by RXE with an incorrect
iCRC, as well as ingress PDUs being dropped due to erroneously detecting
a bad iCRC in the PDU. The fix is to include the pad bytes, if any,
in iCRC computations.
Note: This bug has caused broken on-the-wire compatibility with actual
hardware RoCE devices since the soft-RoCE driver was first put into the
mainstream kernel. Fixing it will create an incompatibility with the
original soft-RoCE devices, but is necessary to be compatible with real
hardware devices.
Make the AFS dynamic root superblock R/W so that SELinux can set the
security label on it. Without this, upgrades to, say, the Fedora
filesystem-afs RPM fail if afs is mounted on it because the SELinux label
can't be (re-)applied.
It might be better to make it possible to bypass the R/O check for LSM
label application through setxattr.
Fixes: 4d673da14533 ("afs: Support the AFS dynamic root") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: selinux@vger.kernel.org
cc: linux-security-module@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
afs_find_server tries to find a server that has an address that
matches the transport address of an rxrpc peer. The code assumes
that the transport address is always ipv6, with ipv4 represented
as ipv4 mapped addresses, but that's not the case. If the transport
family is AF_INET, srx->transport.sin6.sin6_addr.s6_addr32[] will
be beyond the actual ipv4 address and will always be 0, and all
ipv4 addresses will be seen as matching.
As a result, the first ipv4 address seen on any server will be
considered a match, and the server returned may be the wrong one.
One of the consequences is that callbacks received over ipv4 will
only be correctly applied for the server that happens to have the
first ipv4 address on the fs_addresses4 list. Callbacks over ipv4
from all other servers are dropped, causing the client to serve stale
data.
This is fixed by looking at the transport family, and comparing ipv4
addresses based on a sockaddr_in structure rather than a sockaddr_in6.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Right now devfreq_dev_release will print a warning and abort the rest of
the cleanup if the devfreq instance is not part of the global
devfreq_list. But this is a valid scenario, for example it can happen if
the governor can't be found or on any other init error that happens
after device_register.
Initialize devfreq->node to an empty list head in devfreq_add_device so
that list_del becomes a safe noop inside devfreq_dev_release and we can
continue the rest of the cleanup.
The devfreq_notifier_call functions will update scaling_min_freq and
scaling_max_freq when the OPP table is updated.
If fetching the maximum frequency fails then scaling_max_freq remains
set to zero which is confusing. Set to ULONG_MAX instead so we don't
need special handling for this case in other places.
As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
If nvme.write_queues equals the number of CPUs, the driver had decreased
the number of interrupts available such that there could only be one read
queue even if the controller could support more. Remove the interrupt
count reduction in this case. The driver wouldn't request more IRQs than
it wants queues anyway.
The number of poll or write queues should never be negative. Use unsigned
types so that it's not possible to break have the driver not allocate
any queues.
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
