If you configure a route with multiple labels, e.g.
ip route add 10.10.3.0/24 encap mpls 16/100 via 10.10.2.2 dev ens4
A warning is logged:
kernel: [ 130.561819] netlink: 'ip': attribute type 1 has an invalid
length.
This happens because mpls_iptunnel_policy has set the type of
MPLS_IPTUNNEL_DST to fixed size NLA_U32.
Change it to a minimum size.
nla_get_labels() does the remaining validation.
Fixes: e3e4712ec096 ("mpls: ip tunnel support") Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is incorrect to specify the no-ether-link property for the AVB device on
the Ebisu board. This is because the property should only be used when a
board does not provide a proper AVB_LINK signal. However, the Ebisu board
does provide this signal.
As per 87c059e9c39d ("arm64: dts: renesas: salvator-x: Remove renesas,
no-ether-link property") this fixes a bug:
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will have
impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since the
RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
This patch fixes the queued len computation, which could theoretically
be wrong if req->len[1] - req->processed[1] > 1. Be future-proof here,
and fix it.
Fixes: b460edb6230a ("crypto: inside-secure - sha512 support") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
A request is zeroed in safexcel_ahash_exit_inv(). This request total
size is EIP197_AHASH_REQ_SIZE while the memset zeroing it uses
sizeof(struct ahash_request), which happens to be less than
EIP197_AHASH_REQ_SIZE. This patch fixes it.
Fixes: f6beaea30487 ("crypto: inside-secure - authenc(hmac(sha256), cbc(aes)) support") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The assigment of FB_VMODE_NONINTERLACE to var->vmode should be a
bit-wise or of FB_VMODE_NONINTERLACE instead of an assignment,
otherwise the previous clearing of the FB_VMODE_MASK bits of
var->vmode makes no sense and is redundant.
Addresses-Coverity: ("Unused value") Fixes: ad4e02d5081d ("[media] vivid: add a simple framebuffer device for overlay testing") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code defines W1 clock gate to be at 0x1cc, overlaying it
with the IR gate.
Clock gate for r-apb1-w1 is at 0x1ec. This fixes issues with IR receiver
causing interrupt floods on H6 (because interrupt flags can't be cleared,
due to IR module's bus being disabled).
Fixes: b7c7b05065aa77ae ("clk: sunxi-ng: add support for H6 PRCM CCU") Signed-off-by: Ondrej Jirman <megous@megous.com> Acked-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
What we read back from the register is going to be capped at 32-bits,
and cpufreq_freq_table.frequency is an unsigned int. Avoid any possible
value truncation by using the appropriate return value.
There is a logical error in brcm_avs_is_firmware_loaded() whereby if the
firmware returns -EINVAL, we will be reporting this as an error. The
comment is correct, the code was not.
The error return from the call to clk_prepare_enable is not being assigned
to variable ret even though ret is being used to check if the call failed.
Fix this by adding in the missing assignment.
Addresses-Coverity: ("Logically dead code") Fixes: 891a96f65ac3 ("phy: qcom-qusb2: Add support for runtime PM") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid this issue set sock->sk after sk_prot->close.
My grepping and testing did not discover any code which
would depend on the current behaviour.
Fixes: c46234ebb4d1 ("tls: RX path for ktls") Reported-by: David Beckett <david.beckett@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the kzalloc() fails then we should return ERR_PTR(-ENOMEM). In the
current code it's possible that the kzalloc() fails and the
radix_tree_insert() inserts the NULL pointer successfully and we return
the NULL "elm" pointer to the caller. That results in a NULL pointer
dereference.
Fixes: 9ed3e5f44772 ("IB/uverbs: Build the specs into a radix tree at runtime") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a device is stacked like (team, bonding, failsafe or netvsc) the
XDP generic program for the parent device was not called.
Move the call to XDP generic inside __netif_receive_skb_core where
it can be done multiple times for stacked case.
Fixes: d445516966dc ("net: xdp: support xdp generic on virtual devices") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The netvsc VF skb handler should make sure that skb is not
shared. Similar logic already exists in bonding and team device
drivers.
This is not an issue in practice because the VF devicex
does not send up shared skb's. But the netvsc driver
should do the right thing if it did.
Fixes: 0c195567a8f6 ("netvsc: transparent VF management") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver is working well in 'simple cases', but as soon as
more exotic SG lists are provided (dst different from src,
auth part not in a single SG fragment, ...) there are
wrong results, overruns, etc ...
This patch cleans up the AEAD processing by:
- Simplifying the location of 'out of line' ICV
- Never using 'out of line' ICV on encryp
- Always using 'out of line' ICV on decrypt
- Forcing the generation of a SG table on decrypt
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Fixes: aeb4c132f33d ("crypto: talitos - Convert to new AEAD interface") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When hclge_bind_ring_with_vector() fails,
hclge_map_unmap_ring_to_vf_vector() returns the error
directly, so nobody will free the memory allocated by
hclge_get_ring_chain_from_mbx().
So hclge_free_vector_ring_chain() should be called no matter
hclge_bind_ring_with_vector() fails or not.
Fixes: 84e095d64ed9 ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both IPv6 and 6lowpan are calling inet_frags_fini() too soon.
inet_frags_fini() is dismantling a kmem_cache, that might be needed
later when unregister_pernet_subsys() eventually has to remove
frags queues from hash tables and free them.
This fixes potential use-after-free, and is a prereq for the following patch.
Fixes: d4ad4d22e7ac ("inet: frags: use kmem_cache for inet_frag_queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The locking in force_sig_info is not prepared to deal with a task that
exits or execs (as sighand may change). The is not a locking problem
in force_sig as force_sig is only built to handle synchronous
exceptions.
Further the function force_sig_info changes the signal state if the
signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the
delivery of the signal. The signal SIGKILL can not be ignored and can
not be blocked and SIGNAL_UNKILLABLE won't prevent it from being
delivered.
So using force_sig rather than send_sig for SIGKILL is confusing
and pointless.
Because it won't impact the sending of the signal and and because
using force_sig is wrong, replace force_sig with send_sig.
Cc: Namjae Jeon <namjae.jeon@samsung.com> Cc: Jeff Layton <jlayton@primarydata.com> Cc: Steve French <smfrench@gmail.com> Fixes: a5c3e1c725af ("Revert "cifs: No need to send SIGKILL to demux_thread during umount"") Fixes: e7ddee9037e7 ("cifs: disable sharing session and tcon and add new TCP sharing code") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The locking in force_sig_info is not prepared to deal with
a task that exits or execs (as sighand may change). As force_sig
is only built to handle synchronous exceptions.
Further the function force_sig_info changes the signal state if the
signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the
delivery of the signal. The signal SIGKILL can not be ignored and can
not be blocked and SIGNAL_UNKILLABLE won't prevent it from being
delivered.
So using force_sig rather than send_sig for SIGKILL is pointless.
Because it won't impact the sending of the signal and and because
using force_sig is wrong, replace force_sig with send_sig.
Cc: Alexei Starovoitov <ast@kernel.org> Cc: David S. Miller <davem@davemloft.net> Fixes: d2ba09c17a06 ("net: add skeleton of bpfilter kernel module") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The iommu_group_get_for_dev() will allocate a group for a
device if it isn't in any group. This isn't the use case
in iommu_request_dm_for_dev(). Let's use iommu_group_get()
instead.
drivers/misc/sgi-xp/xpc_partition.c:73:14: warning: variable 'buf' is
uninitialized when used within its own initialization [-Wuninitialized]
void *buf = buf;
~~~ ^~~
1 warning generated.
Arnd's explanation during review:
/*
* Returns the physical address of the partition's reserved page through
* an iterative number of calls.
*
* On first call, 'cookie' and 'len' should be set to 0, and 'addr'
* set to the nasid of the partition whose reserved page's address is
* being sought.
* On subsequent calls, pass the values, that were passed back on the
* previous call.
*
* While the return status equals SALRET_MORE_PASSES, keep calling
* this function after first copying 'len' bytes starting at 'addr'
* into 'buf'. Once the return status equals SALRET_OK, 'addr' will
* be the physical address of the partition's reserved page. If the
* return status equals neither of these, an error as occurred.
*/
static inline s64
sn_partition_reserved_page_pa(u64 buf, u64 *cookie, u64 *addr, u64 *len)
so *len is set to zero on the first call and tells the bios how many
bytes are accessible at 'buf', and it does get updated by the BIOS to
tell us how many bytes it needs, and then we allocate that and try again.
Fixes: 279290294662 ("[IA64-SGI] cleanup the way XPC locates the reserved page") Link: https://github.com/ClangBuiltLinux/linux/issues/466 Suggested-by: Stephen Hines <srhines@google.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adds a check on the Transmission Complete bit status before closing the
com port. Prevents the port closure before the end of the transmission.
TC poll loop is moved from stm32_tx_dma_complete to stm32_shutdown
routine, in order to check TC before shutdown in both dma and
PIO tx modes.
TC clear is added in stm32_transmit_char routine, in order to be cleared
before transmitting in both dma and PIO tx modes.
Fixes: 3489187204eb ("serial: stm32: adding dma support") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.
Fixes: 3489187204eb ("serial: stm32: adding dma support") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
- Fixes parity and framing error bit by clearing parity and framing error
flag. The current implementation doesn't clear the error bits when an
error is detected.
- Fixes the incorrect name of framing error clearing flag in header file.
- Fixes misalignement between data frame and errors status. The status
read for "n" frame was the status of "n+1" frame".
- Fixes break detection was not triggered by the expected register.
STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
stm32h7 compatible devices.
As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
stm32f7 and stm32h7 compatible devices.
This patch is fixing word length by configuring correctly the SoC with
supported configurations.
Fixes: ada8618ff3bf ("serial: stm32: adding support for stm32f7") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
alg: skcipher: cbc-des3-ccp encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
The offset value should not be recomputed when retrieving the context.
Also, a code path exists which makes decisions based on older (version 3)
hardware; a v3 device deosn't support 3DES so remove this check.
Fixes: 990672d48515 ('crypto: ccp - Enable 3DES function on v5 CCPs') Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Updated testmgr will exhibit this error message when loading the
ccp-crypto module:
alg: skcipher: cfb-aes-ccp encryption failed with err -22 on test vector 3, cfg="in-place"
Update the CCP crypto driver to correctly treat CFB as a streaming mode
cipher (instead of block mode). Update the configuration for CFB to
specify the block size as a single byte;
Fixes: 2b789435d7f3 ('crypto: ccp - CCP AES crypto API support') Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The eMMC on this board is add-on module which is not mandatory. Removing
'non-removable' property should prevent some errors when booting a board
w/o an eMMC module present.
Commit f33e7bb3eb92 ("dmaengine: tegra210-adma: restore channel status")
added support to save and restore the DMA channel registers when runtime
suspending the ADMA. This change is causing the kernel to crash when
probing the ADMA, if the device is probed deferred when looking up the
channel interrupts. The crash occurs because not all of the channel base
addresses have been setup at this point and in the clean-up path of the
probe, pm_runtime_suspend() is called invoking its callback which
expects all the channel base addresses to be initialised.
Although this could be fixed by simply checking for a NULL address, on
further review of the driver it seems more appropriate that we only call
pm_runtime_get_sync() after all the channel interrupts and base
addresses have been configured. Therefore, fix this crash by moving the
calls to pm_runtime_enable(), pm_runtime_get_sync() and
tegra_adma_init() after the DMA channels have been initialised.
The documentation says there is an SSEN bit on mpll0 but, after testing
it, no spread spectrum function appears to be enabled by this bit on any
of the MPLLs.
mmc1 node where wifi module is connected doesn't have properly defined
power supplies so wifi module is never powered up. Fix that by
specifying additional power supplies.
Additionally, this STB may have either Realtek or Broadcom based wifi
module. One based on Broadcom module also needs external clock to work
properly. Fix that by adding clock property to wifi_pwrseq node.
Fixes: e582b47a9252 ("ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When __afs_break_callback() clears the CB_PROMISED flag, it increments
vnode->cb_break to trigger a future refetch of the status and callback -
however it also calls afs_clear_permits(), which also increments
vnode->cb_break.
Fix this by removing the increment from afs_clear_permits().
Whilst we're at it, fix the conditional call to afs_put_permits() as the
function checks to see if the argument is NULL, so the check is redundant.
__afs_break_callback() holds vnode->lock around its call of
afs_lock_may_be_available() - which also takes that lock.
Fix this by not taking the lock in __afs_break_callback().
Also, there's no point checking the granted_locks and pending_locks queues;
it's sufficient to check lock_state, so move that check out of
afs_lock_may_be_available() into __afs_break_callback() to replace the
queue checks.
Don't invalidate the callback promise on a directory if the
AFS_VNODE_DIR_VALID flag is not set (which indicates that the directory
contents are invalid, due to edit failure, callback break, page reclaim).
The directory will be reloaded next time the directory is accessed, so
clearing the callback flag at this point may race with a reload of the
directory and cancel it's recorded callback promise.
Fix afs_release() to go through the cleanup part of the function if
FMODE_WRITE is set rather than exiting through vfs_fsync() (which skips the
cleanup). The cleanup involves discarding the refs on the key used for
file ops and the writeback key record.
Also fix afs_evict_inode() to clean up any left over wb keys attached to
the inode/vnode when it is removed.
Fixes: 5a8132761609 ("afs: Do better accretion of small writes on newly created content") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function should return NULL in case no device is found, but it
always returns the last checked mc device from the list even if the
index did not match. Fix that.
I did some analysis why this did not raise any issues for about 3 years
and the reason is that edac_mc_find() is mostly used to search for
existing devices. Thus, the bug is not triggered.
[ bp: Drop the if (mci->mc_idx > idx) test in favor of readability. ]
The CPU load values passed to the thermal_power_cpu_get_power
tracepoint are zero for all CPUs, unless, unless the
thermal_power_cpu_limit tracepoint is enabled too:
There seems to be no good reason for omitting the CPU load information
depending on another tracepoint. My guess is that the intention was to
check whether thermal_power_cpu_get_power is (still) enabled, however
'load_cpu != NULL' already indicates that it was at least enabled when
cpufreq_get_requested_power() was entered, there seems little gain
from omitting the assignment if the tracepoint was just disabled, so
just remove the check.
Fixes: 6828a4711f99 ("thermal: add trace events to the power allocator governor") Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Javi Merino <javi.merino@kernel.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently IRQF_SHARED type interrupt line is allocated, but it
is not appropriate, as the interrupt line isn't shared between
different devices, instead IRQF_ONESHOT is the proper type.
By changing interrupt type to IRQF_ONESHOT, now irq handler is
no longer needed, as clear of interrupt status can be done in
threaded interrupt context.
Because IRQF_ONESHOT type interrupt line is kept disabled until
the threaded handler has been run, so there is no need to protect
read/write of REG_GEN3_IRQSTR with lock.
Fixes: 7d4b269776ec6 ("enable hardware interrupts for trip points") Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Tested-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
lm3630a_bank_a_update_status() and lm3630a_bank_b_update_status()
both return the brightness value if the brightness was successfully
updated. Writing to these attributes via sysfs would cause a 'Bad
address' error to be returned. These functions should return 0 on
success, so let's change it to correct that error.
Fixes: 28e64a68a2ef ("backlight: lm3630: apply chip revision") Signed-off-by: Brian Masney <masneyb@onstation.org> Acked-by: Pavel Machek <pavel@ucw.cz> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "whichcpu" comes from argv[3]. The cpu_online() macro looks up the
cpu in a bitmap of online cpus, but if the value is too high then it
could read beyond the end of the bitmap and possibly Oops.
Fixes: 5d5314d6795f ("kdb: core for kgdb back end (1 of 2)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
NFP shift instruction has something special. If shift direction is left
then shift amount of 1 to 31 is specified as 32 minus the amount to shift.
But no need to do this for indirect shift which has shift amount be 0. Even
after we do this subtraction, shift amount 0 will be turned into 32 which
will eventually be encoded the same as 0 because only low 5 bits are
encoded, but shift amount be 32 will fail the FIELD_PREP check done later
on shift mask (0x1f), due to 32 is out of mask range. Such error has been
observed when compiling nfp/bpf/jit.c using gcc 8.3 + O3.
This issue has started when indirect shift support added after which the
incoming shift amount to __emit_shf could be 0, therefore it is at that
time shift amount adjustment inside __emit_shf should have been tightened.
Fixes: 991f5b3651f6 ("nfp: bpf: support logic indirect shifts (BPF_[L|R]SH | BPF_X)") Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by: Pablo Cascón <pablo.cascon@netronome.com Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix lack of keyboard interrupts for RiscPC due to incorrect conversion.
Fixes: e8d36d5dbb6a ("ARM: kill off set_irq_flags usage") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an abnormally low about 20ms,when setting duty repeatedly.
Because setting the duty will disable PWM and then enable. Delete
this operation now.
Fixes: 211ed630753d2f ("pwm: Add support for Meson PWM Controller") Signed-off-by: Bichao Zheng <bichao.zheng@amlogic.com>
[ Dropped code instead of hiding it behind a comment ] Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pre-divider allows configuring longer PWM periods compared to using
the input clock directly. The pre-divider is 7 bit wide, meaning it's
maximum value is 128 (the register value is off-by-one: 0x7f or 127).
Change the loop to also allow for the maximum possible value to be
considered valid.
Fixes: 211ed630753d2f ("pwm: Add support for Meson PWM Controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If userspace provides a rule blob with trailing data after last target,
we trigger a splat, then convert ruleset to 64bit format (with trailing
data), then pass that to do_replace_finish() which then returns -EINVAL.
Erroring out right away avoids the splat plus unneeded translation and
error unwind.
The "out_data" variable is uninitialized at the point. Originally, this
used to print "status" instead and that seems like the correct thing to
print.
Fixes: bc2ef884320b ("alienware-wmi: For WMAX HDMI method, introduce a way to query HDMI cable status") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In vpbe_enum_outputs() we check if (temp_index >= cfg->num_outputs) but
the problem is that "temp_index" can be negative. This patch changes
the types to unsigned to address this array underflow bug.
The "b->index" is a u32 the comes from the user in the ioctl. It hasn't
been checked. We aren't supposed to use it but we're instead supposed
to use the value that gets written to it when we call videobuf_dqbuf().
The videobuf_dqbuf() first memsets it to zero and then re-initializes it
inside the videobuf_status() function. It's this final value which we
want.
Hans Verkuil pointed out that we need to check the return from
videobuf_dqbuf(). I ended up doing a little cleanup related to that as
well.
Fixes: 72915e851da9 ("[media] V4L2: OMAP: VOUT: dma map and unmap v4l2 buffers in qbuf and dqbuf") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The build of aica sound driver has been broken since the timer API
conversion and some code rewrite. This patch fixes the breakage by
using the common substream field, as well as a bit cleaning up wrt the
timer handling in the code.
Fixes: d522bb6a105f ("ALSA: sh: aica: Convert timers to use timer_setup()") Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If alloc_workqueue fails in l2tp_init, l2tp_net_ops
is unregistered on failure path. Then l2tp_exit_net
is called which will flush NULL workqueue, this patch
add a NULL check to fix it.
Fixes: 67e04c29ec0d ("l2tp: unregister l2tp_net_ops on failure path") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
device_for_each_child() stops executing callback function for remaining
child devices, if callback hits an error.
Each child mdev device is independent of each other.
While unregistering parent device, mdev core must remove all child mdev
devices.
Therefore, mdev_device_remove_cb() always returns success so that
device_for_each_child doesn't abort if one child removal hits error.
While at it, improve remove and unregister functions for below simplicity.
There isn't need to pass forced flag pointer during mdev parent
removal which invokes mdev_device_remove(). So simplify the flow.
mdev_device_remove() is called from two paths.
1. mdev_unregister_driver()
mdev_device_remove_cb()
mdev_device_remove()
2. remove_store()
mdev_device_remove()
mdev_remove_sysfs_files() should follow exact mirror sequence of a
create, similar to what is followed in error unwinding path of
mdev_create_sysfs_files().
During mdev parent registration in mdev_register_device(),
if parent device is duplicate, it releases the reference of existing
parent device.
This is incorrect. Existing parent device should not be touched.
Currently the protected management frames are
not appended with the MIC_LEN which results in
the protected management frames being encoded
incorrectly.
Add the extra space at the end of the protected
management frames to fix this encoding error for
the protected management frames.
Fixes: 1807da49733e ("ath10k: wmi: add management tx by reference support over wmi") Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function mmc_alloc_host, the function put_device is called to
release allocated resources when mmc_gpio_alloc fails. Finally, the
function pointed by host->class_dev.class->dev_release (i.e.,
mmc_host_classdev_release) is used to release resources including the
host structure. However, after put_device, host is used and released
again. Resulting in a use-after-free bug.
The driver registers the watchdog with devm_watchdog_register_device() but
still calls watchdog_unregister_device() on remove. Since clocks have to
be stopped when removing the driver, after the watchdog device has been
unregistered, we can not drop the call to watchdog_unregister_device().
Use watchdog_register_device() to register the watchdog.
Status of ADMA channel registers is not saved and restored during system
suspend. During active playback if system enters suspend, this results in
wrong state of channel registers during system resume and playback fails
to resume properly. Fix this by saving following channel registers in
runtime suspend and restore during runtime resume.
* ADMA_CH_LOWER_SRC_ADDR
* ADMA_CH_LOWER_TRG_ADDR
* ADMA_CH_FIFO_CTRL
* ADMA_CH_CONFIG
* ADMA_CH_CTRL
* ADMA_CH_CMD
* ADMA_CH_TC
Runtime PM calls will be inovked during system resume path if a playback
or capture needs to be resumed. Hence above changes work fine for system
suspend case.
Fixes: f46b195799b5 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA") Signed-off-by: Sameer Pujar <spujar@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ena_com_set_hash_function() tests if a hash function is supported
by the device before setting it.
The test returns the opposite result than needed.
Reverse the condition to return the correct value.
Also use the BIT macro instead of inline shift.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ena_up() calls ena_init_napi() but does not call ena_del_napi() in
case of failure. This causes a segmentation fault upon rmmod when
netif_napi_del() is called. Fix this bug by calling ena_del_napi()
before returning error from ena_up().
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kernel parameter igfx_off is used by users to disable
DMA remapping for the Intel integrated graphic device. It
was designed for bare metal cases where a dedicated IOMMU
is used for graphic. This doesn't apply to virtual IOMMU
case where an include-all IOMMU is used. This makes the
kernel parameter work with virtual IOMMU as well.
Cc: Ashok Raj <ashok.raj@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Suggested-by: Kevin Tian <kevin.tian@intel.com> Fixes: c0771df8d5297 ("intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.") Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Tested-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The QP transition optional parameters for the various transition for XRC
QPs are identical to those for RC QPs.
Many of the XRC QP transition optional parameter bits are missing from the
QP optional mask table. These omissions caused failures when doing XRC QP
state transitions.
For example, when trying to change the response timer of an XRC receive QP
via the RTS2RTS transition, the new timer value was ignored because
MLX5_QP_OPTPAR_RNR_TIMEOUT bit was missing from the optional params mask
for XRC qps for the RTS2RTS transition.
Fix this by adding the missing XRC optional parameters for all QP
transitions to the opt_mask table.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Fixes: a4774e9095de ("IB/mlx5: Fix opt param mask according to firmware spec") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A stream may specify a rate range using 'rate_min' and 'rate_max', so a
stream may be valid and not specify any rates. However, as stream cannot
be valid and not have any channel. Let's use this condition instead to
determine if a stream is valid or not.
Fixes: cde79035c6cf ("ASoC: Handle multiple codecs with split playback / capture") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Packet send checks that msg_name is at least sizeof sockaddr_ll.
Packet recv must return at least this length, so that its output
can be passed unmodified to packet send.
This ceased to be true since adding support for lladdr longer than
sll_addr. Since, the return value uses true address length.
Always return at least sizeof sockaddr_ll, even if address length
is shorter. Zero the padding bytes.
Change v1->v2: do not overwrite zeroed padding again. use copy_len.
Fixes: 0fb375fb9b93 ("[AF_PACKET]: Allow for > 8 byte hardware addresses.") Suggested-by: David Laight <David.Laight@aculab.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
This was previosly fixed on Torpedo, but missed on the SOM-LV
Fixes: 5cb8b0fa55a9 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is fixing flow offload for UDP traffic where packets only follow
one single direction.
The flow_offload_fixup_tcp() mechanism works fine in case that the
offloaded entry remains in SYN_RECV state, given sequence tracking is
reset and that conntrack handles syn+ack packets as a retransmission, ie.
The trace_hardirqs_on() sets current->hardirqs_enabled and from here
the lockdep assumes interrupts are enabled although they are remain
disabled until the context switches to the guest. Consequent
srcu_read_lock() checks the flags in rcu_lock_acquire(), observes
disabled interrupts and prints a warning (see below).
This moves trace_hardirqs_on/off closer to __kvmppc_vcore_entry to
prevent lockdep from being confused.
The "(&ctio->u.status1.sense_data)[i]" where i >= 0 expressions in
qlt_send_resp_ctio() are probably typos and should have been
"(&ctio->u.status1.sense_data[4 * i])" instead. Instead of only fixing
these typos, modify the code for storing sense data such that it becomes
easy to read. This patch fixes a Coverity complaint about accessing an
array outside its bounds.
Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: be25152c0d9e ("qla2xxx: Improve T10-DIF/PI handling in driver.") # v4.11. Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The test "if (!cmd)" is not useful because it is guaranteed that cmd !=
NULL. Instead of testing the cmd pointer, rely on the tag to decide
whether or not command allocation failed.
Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Giridhar Malavali <gmalavali@marvell.com> Fixes: 33e799775593 ("qla2xxx: Add support for QFull throttling and Term Exchange retry") # v3.18. Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When loading an ELF image via kexec_file the segment alignment is ignored
in the calculation for the load address of the next segment. When there are
multiple segments this can lead to segment overlap and thus load failure.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com> Fixes: 8be018827154 ("s390/kexec_file: Add ELF loader") Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang points out a syntax error, as the etr_catu_buf_ops structure is
declared 'static' before the type is known:
In file included from drivers/hwtracing/coresight/coresight-tmc-etr.c:12:
drivers/hwtracing/coresight/coresight-catu.h:116:40: warning: tentative definition of variable with internal linkage has incomplete non-array type 'const struct etr_buf_operations' [-Wtentative-definition-incomplete-type]
static const struct etr_buf_operations etr_catu_buf_ops;
^
drivers/hwtracing/coresight/coresight-catu.h:116:21: note: forward declaration of 'struct etr_buf_operations'
static const struct etr_buf_operations etr_catu_buf_ops;
This seems worth fixing in the code, so replace pointer to the empty
constant structure with a NULL pointer. We need an extra NULL pointer
check here, but the result should be better object code otherwise,
avoiding the silly empty structure.
Fixes: 434d611cddef ("coresight: catu: Plug in CATU as a backend for ETR buffer") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed line over 80 characters] Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When flushing out dirty pages, the fact that we may hit fatal errors
is not a reason to stop writeback. Those errors are reported through
fsync(), not through the flush mechanism.
Fixes: a6598813a4c5b ("NFS: Don't write back further requests if there...") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Further fix the file locking in the afs filesystem client in a number of
ways, including:
(1) Don't submit the operation to obtain a lock from the server in a work
queue context, but rather do it in the process context of whoever
issued the requesting system call.
(2) The owner of the file_lock struct at the front of the pending_locks
queue now owns right to talk to the server.
(3) Write locks can be instantly granted if they don't overlap with any
other locks *and* we have a write lock on the server.
(4) In the event of an authentication/permission error, all other matching
pending locks requests are also immediately aborted.
(5) Properly use VFS core locks_lock_file_wait() to distribute the server
lock amongst local client locks, including waiting for the lock to
become available.
With the version of sqlite3 that I have, this should fail consistently with
EAGAIN, whether or not the program is straced (which introduces some delays
between lock syscalls).
Fixes: 0fafdc9f888b ("afs: Fix file locking") Reported-by: Jonathan Billings <jsbillin@umich.edu> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix AFS file locking to allow fine grained locks as some applications, such
as firefox, won't work if they can't take such locks on certain state files
- thereby preventing the use of kAFS to distribute a home directory.
Note that this cannot be made completely functional as the protocol only
has provision for whole-file locks, so there exists the possibility of a
process deadlocking itself by getting a partial read-lock on a file first
and then trying to get a non-overlapping write-lock - but we got the
server's read lock with the first lock, so we're now stuck.
OpenAFS solves this by just granting any partial-range lock directly
without consulting the server - and hoping there's no remote collision. I
want to implement that in a separate patch and it requires a bit more
thought.
Fixes: 8d6c554126b8 ("AFS: implement file locking") Reported-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error from snd_usb_mixer_apply_create_quirk() is ignored in the
current usb-audio driver code, which will continue the probing even
after the error. Let's take it more serious.
In 2D transfers (for the AXI DMAC), the number of frames (numf) represents
Y_LENGTH, and the length of a frame is X_LENGTH. 2D transfers are useful
for video transfers where screen resolutions ( X * Y ) are typically
aligned for X, but not for Y.
There is no requirement for Y_LENGTH to be aligned to the bus-width (or
anything), and this is also true for AXI DMAC.
Checking the Y_LENGTH for alignment causes false errors when initiating DMA
transfers. This change fixes this by checking only that the Y_LENGTH is
non-zero.
Fixes: 0e3b67b348b8 ("dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller") Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
NEXTHDR_MAX is 255. What happens here is that we take a u8 value
"hdr->nexthdr" from the network and then look it up in
lowpan_nexthdr_nhcs[]. The problem is that if hdr->nexthdr is 0xff then
we read one element beyond the end of the array so the array needs to
be one element larger.
Fixes: 92aa7c65d295 ("6lowpan: add generic nhc layer interface") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Acked-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each eTSEC MAC has its own TBI (SGMII) PCS and private MDIO bus.
But due to a DTS oversight, both SGMII-compatible MACs of the LS1021 SoC
are pointing towards the same internal PCS. Therefore nobody is
controlling the internal PCS of eTSEC0.
Upon initial ndo_open, the SGMII link is ok by virtue of U-boot
initialization. But upon an ifdown/ifup sequence, the code path from
ndo_open -> init_phy -> gfar_configure_serdes does not get executed for
the PCS of eTSEC0 (and is executed twice for MAC eTSEC1). So the SGMII
link remains down for eTSEC0. On the LS1021A-TWR board, to signal this
failure condition, the PHY driver keeps printing
'803x_aneg_done: SGMII link is not ok'.
Also, it changes compatible of mdio0 to "fsl,etsec2-mdio" to match
mdio1 device.
Fixes: 055223d4d22d ("ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 32-bit vDSO is not needed and not normally built for 64-bit
little-endian configurations. However, the vdso_install target still
builds and installs it. Add the same config condition as is normally
used for the build.
Fixes: e0d005916994 ("powerpc/vdso: Disable building the 32-bit VDSO ...") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the various compiler warnings when building the msgque
selftest. The primary change is using sys/msg.h instead of linux/msg.h
directly to gain the API declarations.
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.
This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.
The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.
To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...") Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: cc79dd1ba9c10 ("tipc: change socket buffer overflow control to respect sk_rcvbuf") Fixes: a5325ae5b8bff ("tipc: add name distributor resiliency queue") Signed-off-by: Jie Liu <liujie165@huawei.com> Reported-by: Qiang Ning <ningqiang1@huawei.com> Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
