If we free a metadata buffer which has been failed to async write out
in the background, the jbd2 checkpoint procedure will not detect this
failure in jbd2_log_do_checkpoint(), so it may lead to filesystem
inconsistency after cleanup journal tail. This patch abort the journal
if free a buffer has write_io_error flag to prevent potential further
inconsistency.
There is a risk of filesystem inconsistency if we failed to async write
back metadata buffer in the background. Because of current buffer's end
io procedure is handled by end_buffer_async_write() in the block layer,
and it only clear the buffer's uptodate flag and mark the write_io_error
flag, so ext4 cannot detect such failure immediately. In most cases of
getting metadata buffer (e.g. ext4_read_inode_bitmap()), although the
buffer's data is actually uptodate, it may still read data from disk
because the buffer's uptodate flag has been cleared. Finally, it may
lead to on-disk filesystem inconsistency if reading old data from the
disk successfully and write them out again.
This patch detect bdev mapping->wb_err when getting journal's write
access and mark the filesystem error if bdev's mapping->wb_err was
increased, this could prevent further writing and potential
inconsistency.
cr=0 is supposed to be an optimization to save CPU cycles, but if
buddy data (in memory) is not initialized then all this makes no sense
as we have to do sync IO taking a lot of cycles. Also, at cr=0
mballoc doesn't choose any available chunk. cr=1 also skips groups
using heuristic based on avg. fragment size. It's more useful to skip
such groups and switch to cr=2 where groups will be scanned for
available chunks. However, we always read the first block group in a
flex_bg so metadata blocks will get read into the first flex_bg if
possible.
Using sparse image and dm-slow virtual device of 120TB was
simulated, then the image was formatted and filled using debugfs to
mark ~85% of available space as busy. mount process w/o the patch
couldn't complete in half an hour (according to vmstat it would take
~10-11 hours). With the patch applied mount took ~20 seconds.
Lustre-bug-id: https://jira.whamcloud.com/browse/LU-12988 Signed-off-by: Alex Zhuravlev <azhuravlev@whamcloud.com> Reviewed-by: Andreas Dilger <adilger@whamcloud.com> Reviewed-by: Artem Blagodarenko <artem.blagodarenko@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ext4 uses blkdev_get_by_dev() to get the block_device for journal device
which does check to see if the read-only block device was opened
read-only.
As a result ext4 will hapily proceed mounting the file system with
external journal on read-only device. This is bad as we would not be
able to use the journal leading to errors later on.
Instead of simply failing to mount file system in this case, treat it in
a similar way we treat internal journal on read-only device. Allow to
mount with -o noload in read-only mode.
A customer has reported a BUG_ON in ext4_clear_journal_err() hitting
during an LTP testing. Either this has been caused by a test setup
issue where the filesystem was being overwritten while LTP was mounting
it or the journal replay has overwritten the superblock with invalid
data. In either case it is preferable we don't take the machine down
with a BUG_ON. So handle the situation of unexpectedly missing
has_journal feature more gracefully. We issue warning and fail the mount
in the cases where the race window is narrow and the failed check is
most likely a programming error. In cases where fs corruption is more
likely, we do full ext4_error() handling before failing mount / remount.
Reviewed-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20200710140759.18031-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Callers of __jbd2_journal_unfile_buffer() and
__jbd2_journal_refile_buffer() assume that the b_transaction is set. In
fact if it's not, we can end up with journal_head refcounting errors
leading to crash much later that might be very hard to track down. Add
asserts to make sure that is the case.
We also make sure that b_next_transaction is NULL in
__jbd2_journal_unfile_buffer() since the callers expect that as well and
we should not get into that stage in this state anyway, leading to
problems later on if we do.
Previously the stm32h7 interrupt thread cleared all non-masked interrupts.
If an interrupt was to occur during the handling of another interrupt its
flag would be unset, resulting in a lost interrupt.
This patches fixes the issue by clearing only the currently set interrupt
flags.
The build is currently broken, if COMPILE_TEST=y and PPC_PMAC=n:
linux/drivers/video/fbdev/controlfb.c: In function ‘control_set_hardware’:
linux/drivers/video/fbdev/controlfb.c:276:2: error: implicit declaration of function ‘btext_update_display’
276 | btext_update_display(p->frame_buffer_phys + CTRLFB_OFF,
| ^~~~~~~~~~~~~~~~~~~~
Fix it by including btext.h whenever CONFIG_BOOTX_TEXT is enabled.
We don't free config irq in ifcvf_free_irq() which will trigger a
BUG() in pci core since we try to free the vectors that has an
action. Fixing this by recording the config irq in ifcvf_hw structure
and free it in ifcvf_free_irq().
Fixes: e7991f376a4d ("ifcvf: implement config interrupt in IFCVF") Cc: Zhu Lingshan <lingshan.zhu@intel.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20200723091254.20617-2-jasowang@redhat.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Zhu Lingshan <lingshan.zhu@intel.com> Fixes: e7991f376a4d ("ifcvf: implement config interrupt in IFCVF") Cc: Zhu Lingshan <a class="moz-txt-link-rfc2396E" href="mailto:lingshan.zhu@intel.com"><lingshan.zhu@intel.com></a> Signed-off-by: Jason Wang <a class="moz-txt-link-rfc2396E" href="mailto:jasowang@redhat.com"><jasowang@redhat.com></a> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When commit c64ffff7a9d1 ("i2c: core: Allow empty id_table in ACPI case
as well") fixed the enumeration of I²C devices on ACPI enabled platforms
when driver has no ID table, it missed the PRP0001 support.
i2c_device_match() and i2c_acpi_match_device() differently match
driver against given device. Use acpi_driver_match_device(), that is used
in the former, in i2c_device_probe() and don't fail PRP0001 enumeration
when no ID table exist.
Fixes: c64ffff7a9d1 ("i2c: core: Allow empty id_table in ACPI case as well") BugLink: https://stackoverflow.com/q/63519678/2511795 Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm scheduler currently expects that the stop/start sequence is always
executed in the timeout handling, as the job at the head of the hardware
execution list is always removed from the ring mirror before the driver
function is called and only inserted back into the list when starting the
scheduler.
This adds some unnecessary overhead if the timeout handler determines
that the GPU is still executing jobs normally and just wished to extend
the timeout, but a better solution requires a major rearchitecture of the
scheduler, which is not applicable as a fix.
Fixes: 135517d3565b ("drm/scheduler: Avoid accessing freed bad job.") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there's only one usable, non-optimized path, nvme_round_robin_path()
returns NULL, which is wrong. Fix it by falling back to "old", like in
the single optimized path case. Also, if the active path isn't changed,
there's no need to re-assign the pointer.
Fixes: 3f6e3246db0e ("nvme-multipath: fix logic for non-optimized paths") Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin George <marting@netapp.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Normally, blkcg_iolatency_exit() will free related memory in iolatency
when cleanup queue. But if blk_throtl_init() return error and queue init
fail, blkcg_iolatency_exit() will not do that for us. Then it cause
memory leak.
c616cbee97ae ("blk-mq: punt failed direct issue to dispatch list") supposed
to add request which has been through ->queue_rq() to the hw queue dispatch
list, however it adds request running out of budget or driver tag to hw queue
too. This way basically bypasses request merge, and causes too many request
dispatched to LLD, and system% is unnecessary increased.
Fixes this issue by adding request not through ->queue_rq into sw/scheduler
queue, and this way is safe because no ->queue_rq is called on this request
yet.
High %system can be observed on Azure storvsc device, and even soft lock
is observed. This patch reduces %system during heavy sequential IO,
meantime decreases soft lockup risk.
Fixes: c616cbee97ae ("blk-mq: punt failed direct issue to dispatch list") Signed-off-by: Ming Lei <ming.lei@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We hit a kernel panic due to a divide by 0 in nct7904_read_fan() for
the hwmon_fan_min case. Extend the check to hwmon_fan_input case as well
for safety.
Changes from v1:
- update commit description with proper ref-accounting justification
commit db37a34c563b ("block, bfq: get a ref to a group when adding it to a service tree")
introduce leak forbfq_group and blkcg_gq objects because of get/put
imbalance.
In fact whole idea of original commit is wrong because bfq_group entity
can not dissapear under us because it is referenced by child bfq_queue's
entities from here:
-> bfq_init_entity()
->bfqg_and_blkg_get(bfqg);
->entity->parent = bfqg->my_entity
So parent entity can not disappear while child entity is in tree,
and child entities already has proper protection.
This patch revert commit db37a34c563b ("block, bfq: get a ref to a group when adding it to a service tree")
bfq_group leak trace caused by bad commit:
-> blkg_alloc
-> bfq_pq_alloc
-> bfqg_get (+1)
->bfq_activate_bfqq
->bfq_activate_requeue_entity
-> __bfq_activate_entity
->bfq_get_entity
->bfqg_and_blkg_get (+1) <==== : Note1
->bfq_del_bfqq_busy
->bfq_deactivate_entity+0x53/0xc0 [bfq]
->__bfq_deactivate_entity+0x1b8/0x210 [bfq]
-> bfq_forget_entity(is_in_service = true)
entity->on_st_or_in_serv = false <=== :Note2
if (is_in_service)
return; ==> do not touch reference
-> blkcg_css_offline
-> blkcg_destroy_blkgs
-> blkg_destroy
-> bfq_pd_offline
-> __bfq_deactivate_entity
if (!entity->on_st_or_in_serv) /* true, because (Note2)
return false;
-> bfq_pd_free
-> bfqg_put() (-1, byt bfqg->ref == 2) because of (Note2)
So bfq_group and blkcg_gq will leak forever, see test-case below.
##TESTCASE_BEGIN:
#!/bin/bash
max_iters=${1:-100}
#prep cgroup mounts
mount -t tmpfs cgroup_root /sys/fs/cgroup
mkdir /sys/fs/cgroup/blkio
mount -t cgroup -o blkio none /sys/fs/cgroup/blkio
Fixes: db37a34c563b ("block, bfq: get a ref to a group when adding it to a service tree") Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Dmitry Monakhov <dmtrmonakhov@yandex-team.ru> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we pass in an offset which is larger than PAGE_SIZE, then
page_is_mergeable() thinks it's not mergeable with the previous bio_vec,
leading to a large number of bio_vecs being used. Use a slightly more
obvious test that the two pages are compatible with each other.
Fixes: 52d52d1c98a9 ("block: only allow contiguous page structs in a bio_vec") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to set it to the most recent completed fence, not the most
recent submitted. Otherwise we have races where we think we can retire
submits that the GPU is not finished with, if the GPU doesn't manage to
overwrite the seqno before we look at it.
This can show up with hang recovery if one of the submits after the
crashing submit also hangs after it is replayed.
Fixes: f97decac5f4c ("drm/msm: Support multiple ringbuffers") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
1f23816b8eb8 ("virtio_blk: add discard and write zeroes support") starts
to support multi-range discard for virtio-blk. However, the virtio-blk
disk may report max discard segment as 1, at least that is exactly what
qemu is doing.
So far, block layer switches to normal request merge if max discard segment
limit is 1, and multiple bios can be merged to single segment. This way may
cause memory corruption in virtblk_setup_discard_write_zeroes().
Fix the issue by handling single max discard segment in straightforward
way.
Fixes: 1f23816b8eb8 ("virtio_blk: add discard and write zeroes support") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Changpeng Liu <changpeng.liu@intel.com> Cc: Daniel Verkamp <dverkamp@chromium.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When queue_max_discard_segments(q) is 1, blk_discard_mergable() will
return false for discard request, then normal request merge is applied.
However, only queue_max_segments() is checked, so max discard segment
limit isn't respected.
Check max discard segment limit in the request merge code for fixing
the issue.
Discard request failure of virtio_blk is fixed.
Fixes: 69840466086d ("block: fix the DISCARD request merge") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an NFSv2/v3 client breaks an NFSv4 client's delegation, it will hit a
NULL dereference in nfsd_breaker_owns_lease().
Easily reproduceable with for example
mount -overs=4.2 server:/export /mnt/
sleep 1h </mnt/file &
mount -overs=3 server:/export /mnt2/
touch /mnt2/file
Reported-by: Robert Dinse <nanook@eskimo.com> Fixes: 28df3d1539de50 ("nfsd: clients don't need to break their own delegations") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208807 Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Capture and playback endpoints on Saffire 6 (USB 1.1) resides on the same
interface. This was not supported by the composite quirk back in the day
when initial support for this device was added, thus only playback was
enabled until now.
Fixes: 11e424e88bd4 ("ALSA: usb-audio: Add support for Focusrite Saffire 6 USB") Signed-off-by: Alexander Tsoy <alexander@tsoy.me> Cc: <stable.vger.kernel.org> Link: https://lore.kernel.org/r/20200815002103.29247-1-alexander@tsoy.me Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because intel_pstate_set_energy_pref_index() reads and writes the
MSR_HWP_REQUEST register without using the cached value of it used by
intel_pstate_hwp_boost_up() and intel_pstate_hwp_boost_down(), those
functions may overwrite the value written by it and so the EPP value
set via sysfs may be lost.
To avoid that, make intel_pstate_set_energy_pref_index() take the
cached value of MSR_HWP_REQUEST just like the other two routines
mentioned above and update it with the new EPP value coming from
user space in addition to updating the MSR.
Note that the MSR itself still needs to be updated too in case
hwp_boost is unset or the boosting mechanism is not active at the
EPP change time.
Fixes: e0efd5be63e8 ("cpufreq: intel_pstate: Add HWP boost utility and sched util hooks") Reported-by: Francisco Jerez <currojerez@riseup.net> Cc: 4.18+ <stable@vger.kernel.org> # 4.18+: 3da97d4db8ee cpufreq: intel_pstate: Rearrange ... Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid some issues, for example RCU usage warning and double free,
we should flush the flows under ovs_lock. This patch refactors
table_instance_destroy and introduces table_instance_flow_flush
which can be invoked by __dp_destroy or ovs_flow_tbl_flush.
Fixes: 50b0e61b32ee ("net: openvswitch: fix possible memleak on destroy flow-table") Reported-by: Johan Knöös <jknoos@google.com>
Reported-at: https://mail.openvswitch.org/pipermail/ovs-discuss/2020-August/050489.html Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver using cpu_logical_map() macro which will expand to
__cpu_logical_map, we can't access it in a drvier. Let's turn
cpu_logical_map() into a C wrapper and export it to fix the
build issue.
Also create a function set_cpu_logical_map(cpu, hwid) when assign
a value to cpu_logical_map(cpu).
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_EFI is not enabled, we might get an undefined reference to
efi_enter_virtual_mode() error, if this efi_enabled() call isn't inlined
into start_kernel(). This happens in particular, if start_kernel() is
annodated with __no_sanitize_address.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Elena Petrova <lenaptr@google.com> Cc: Marco Elver <elver@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Walter Wu <walter-zh.wu@mediatek.com> Link: http://lkml.kernel.org/r/6514652d3a32d3ed33d6eb5c91d0af63bf0d1a0c.1596544734.git.andreyknvl@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set the timeout value as per cfg80211's set_power_mgmt() request. If the
requested value value is left undefined we set it to 2 seconds, the
maximum supported value.
The initial code that was adding delays was doing a cast over undefined
memory. This meant that the delays would be all gibberish.
This change, allocates all delays on the stack, and assigns them from the
ZynqMP & Versal macros/phase-list. And then finally copies them over the
common iclk_phase & oclk_phase variables.
The char buffer buf, receives data directly from user space,
so its content might be negative and its elements are left
shifted to form an unsigned integer.
Since left shifting a negative value is undefined behavior, thus
change the char to u8 to elimintate this UB.
Fix build errors when CONFIG_PCI_MSI is not enabled by making the
driver depend on PCI_MSI:
ld: drivers/dma/idxd/device.o: in function `idxd_mask_msix_vector':
device.c:(.text+0x26f): undefined reference to `pci_msi_mask_irq'
ld: drivers/dma/idxd/device.o: in function `idxd_unmask_msix_vector':
device.c:(.text+0x2af): undefined reference to `pci_msi_unmask_irq'
The kernel test robot pointed out a slightly different error message
after recent commit 5456ffdee666 ("powerpc/spufs: simplify spufs core
dumping") to spufs for a configuration that never worked:
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_proxydma_info_dump':
>> file.c:(.text+0x4c68): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_dma_info_dump':
file.c:(.text+0x4d70): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_wbox_info_dump':
file.c:(.text+0x4df4): undefined reference to `.dump_emit'
Add a Kconfig dependency to prevent this from happening again.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200706132302.3885935-1-arnd@arndb.de Signed-off-by: Sasha Levin <sashal@kernel.org>
__hyp_call_panic_nvhe contains inline assembly which did not declare
its dependency on the __hyp_panic_string symbol.
The static-declared string has previously been kept alive because of a use in
__hyp_call_panic_vhe. Fix this in preparation for separating the source files
between VHE and nVHE when the two users land in two different compilation
units. The static variable otherwise gets dropped when compiling the nVHE
source file, causing an undefined symbol linker error later.
According to https://www.kernel.org/doc/Documentation/gpio/consumer.txt,
- all of the gpiod_set_value_xxx() functions operate with the *logical*
value. So in imx290_power_on() the reset signal should be cleared
(de-asserted) with gpiod_set_value_cansleep(imx290->rst_gpio, 0), and in
imx290_power_off() the value of 1 must be used to apply/assert the reset
to the sensor. In the device tree the reset pin is described as
GPIO_ACTIVE_LOW, and gpiod_set_value_xxx() functions take this into
account,
- when devm_gpiod_get_optional() is called with GPIOD_ASIS, the GPIO is
not initialized, and the direction must be set later; using a GPIO
without setting its direction first is illegal and will result in undefined
behavior. Fix this by using GPIOD_OUT_HIGH instead of GPIOD_ASIS (this
asserts the reset signal to the sensor initially).
In case of errors vpif_probe_complete() releases memory for vpif_obj.sd
and unregisters the V4L2 device. But then this is done again by
vpif_probe() itself. The patch removes the cleaning from
vpif_probe_complete().
Found by Linux Driver Verification project (linuxtesting.org).
syzbot found issues with having hugetlbfs on a union/overlay as reported
in [1]. Due to the limitations (no write) and special functionality of
hugetlbfs, it does not work well in filesystem stacking. There are no
know use cases for hugetlbfs stacking. Rather than making modifications
to get hugetlbfs working in such environments, simply prevent stacking.
The Intel uncore driver may claim some of the pci ids from ie31200 which
means that the ie31200 edac driver will not initialize them as part of
pci_register_driver().
Let's add a fallback for this case to 'pci_get_device()' to get a
reference on the device such that it can still be configured. This is
similar in approach to other edac drivers.
In aio case, if the completion comes very fast just before the
ceph_read_iter() returns to fs/aio.c, the kiocb will be freed in
the completion callback, then if ceph_read_iter() access again
we will potentially hit the use-after-free bug.
[ jlayton: initialize direct_lock early, and use it everywhere ]
URL: https://tracker.ceph.com/issues/45649 Signed-off-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure the delayed work stopped before releasing the resources.
cancel_delayed_work_sync() will only guarantee that the work finishes
executing if the work is already in the ->worklist. That means after
the cancel_delayed_work_sync() returns, it will leave the work requeued
if it was rearmed at the end. That can lead to a use after free once the
work struct is freed.
Fix it by flushing the delayed work instead of trying to cancel it, and
ensure that the work doesn't rearm if the mdsc is stopping.
URL: https://tracker.ceph.com/issues/46293 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
vfs_inode is used only for the inode number everything else requires
btrfs_inode.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ use btrfs_ino ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The incoming qgroup reserved space timing will move the data reservation
to ordered extent completely.
However in btrfs_punch_hole_lock_range() will call
btrfs_invalidate_page(), which will clear QGROUP_RESERVED bit for the
range.
In current stage it's OK, but if we're making ordered extents handle the
reserved space, then btrfs_punch_hole_lock_range() can clear the
QGROUP_RESERVED bit before we submit ordered extent, leading to qgroup
reserved space leakage.
So here change the timing to make reserve data space after
btrfs_punch_hole_lock_range().
The new timing is fine for either current code or the new code.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Though the number of lock-acquisitions is tracked as unsigned long, this
is passed as the divisor to div_s64() which interprets it as a s32,
giving nonsense values with more than 2 billion acquisitons. E.g.
nouveau_connector_detect() calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
nv50_disp_atomic_commit() calls calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
nouveau_fbcon_open() calls calls pm_runtime_get_sync() that
increments the reference count. In case of failure, decrement the
ref count before returning the error.
During umount, f2fs_put_super() unregisters procfs entries after
f2fs_destroy_segment_manager(), it may cause use-after-free
issue when umount races with procfs accessing, fix it by relocating
f2fs_unregister_sysfs().
[Chao Yu: change commit title/message a bit]
Signed-off-by: Li Guifu <bluce.liguifu@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Logitech GROUP is a compound with camera and audio.
When the HID interface in an audio device is requested to get
specific report id, all following control transfers are stalled
and never be restored back.
The rt711 jack detection properties are set from the machine drivers
during the card probe, as done in other ASoC examples.
KASAN reports a use-after-free error when unbinding drivers due to a
confusing sequence between the ACPI core, the device core and the
SoundWire device cleanups.
Rather than fixing this sequence, follow the recommendation to have
the same caller add and remove properties, add an explicit
device_remove_properties() in the card .remove() callback.
In future patches the use of device_add/remove_properties will be
replaced by a direct handling of a swnode, but the sequence will
remain the same.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20200717211337.31956-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse.
To use the TMR_FIPER register to generate desired periodic
pulses. The value should programmed is,
desired_period - tclk_period
Current tmr-fiper2 value is to generate 100us periodic pulses.
(But the value should have been 99995, not 99990. The tclk_period is 5.)
This patch is to generate 1 second periodic pulses with value 999999995 programmed which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kobject_init_and_add() takes a reference even when it fails. If it returns
an error, kobject_put() must be called to clean up the memory associated
with the object.
When kobject_init_and_add() fails, call kobject_put() instead of kfree().
b8eb718348b8 ("net-sysfs: Fix reference count leak in
rx|netdev_queue_add_kobject") fixed a similar problem.
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
- don't panic kernel if f2fs_get_node_page() fails in
f2fs_recover_inline_data() or f2fs_recover_inline_xattr();
- return error number of f2fs_truncate_blocks() to
f2fs_recover_inline_data()'s caller;
An extra count on ebb_state.stats.pmc_count[PMC_INDEX(pmc)] is being per-
formed when count_pmc() is used to reset PMCs on a few selftests. This
extra pmc_count can occasionally invalidate results, such as the ones from
cycles_test shown hereafter. The ebb_check_count() failed with an above
the upper limit error due to the extra value on ebb_state.stats.pmc_count.
Furthermore, this extra count is also indicated by extra PMC1 trace_log on
the output of the cycle test (as well as on pmc56_overflow_test):
transport_init_session can allocate memory via percpu_ref_init, and
target_xcopy_release_pt never frees it. This adds a
transport_uninit_session function to handle cleanup of resources allocated
in the init function.
In tracking down a problem in this patchset, I discovered we are
reclaiming dirty stale inodes. This wasn't discovered until inodes
were always attached to the cluster buffer and then the rcu callback
that freed inodes was assert failing because the inode still had an
active pointer to the cluster buffer after it had been reclaimed.
Debugging the issue indicated that this was a pre-existing issue
resulting from the way the inodes are handled in xfs_inactive_ifree.
When we free a cluster buffer from xfs_ifree_cluster, all the inodes
in cache are marked XFS_ISTALE. Those that are clean have nothing
else done to them and so eventually get cleaned up by background
reclaim. i.e. it is assumed we'll never dirty/relog an inode marked
XFS_ISTALE.
On journal commit dirty stale inodes as are handled by both
buffer and inode log items to run though xfs_istale_done() and
removed from the AIL (buffer log item commit) or the log item will
simply unpin it because the buffer log item will clean it. What happens
to any specific inode is entirely dependent on which log item wins
the commit race, but the result is the same - stale inodes are
clean, not attached to the cluster buffer, and not in the AIL. Hence
inode reclaim can just free these inodes without further care.
However, if the stale inode is relogged, it gets dirtied again and
relogged into the CIL. Most of the time this isn't an issue, because
relogging simply changes the inode's location in the current
checkpoint. Problems arise, however, when the CIL checkpoints
between two transactions in the xfs_inactive_ifree() deferops
processing. This results in the XFS_ISTALE inode being redirtied
and inserted into the CIL without any of the other stale cluster
buffer infrastructure being in place.
Hence on journal commit, it simply gets unpinned, so it remains
dirty in memory. Everything in inode writeback avoids XFS_ISTALE
inodes so it can't be written back, and it is not tracked in the AIL
so there's not even a trigger to attempt to clean the inode. Hence
the inode just sits dirty in memory until inode reclaim comes along,
sees that it is XFS_ISTALE, and goes to reclaim it. This reclaiming
of a dirty inode caused use after free, list corruptions and other
nasty issues later in this patchset.
Hence this patch addresses a violation of the "never log XFS_ISTALE
inodes" caused by the deferops processing rolling a transaction
and relogging a stale inode in xfs_inactive_free. It also adds a
bunch of asserts to catch this problem in debug kernels so that
we don't reintroduce this problem in future.
Reproducer for this issue was generic/558 on a v4 filesystem.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
in amdgpu_display_crtc_set_config, the call to pm_runtime_get_sync
increments the counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
in amdgpu_drm_ioctl the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
in amdgpu_driver_open_kms the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Signed-off-by: Qiushi Wu <wu000273@umn.edu> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
EC is using 32 bit timestamps (us), and before converting it to 64bit
they were not casted, so it would overflow every 4s.
Regular overflow every ~70 minutes was not taken into account either.
Unlike the other instances which represent a complete loss of
consistency within the rcache mechanism itself, or a fundamental
and obvious misconfiguration by an IOMMU driver, the BUG_ON() in
iova_magazine_free_pfns() can be provoked at more or less any time
in a "spooky action-at-a-distance" manner by any old device driver
passing nonsense to dma_unmap_*() which then propagates through to
queue_iova().
Not only is this well outside the IOVA layer's control, it's also
nowhere near fatal enough to justify panicking anyway - all that
really achieves is to make debugging the offending driver more
difficult. Let's simply WARN and otherwise ignore bogus PFNs.
Intel Tiger Lake PCH-H has the same LPSS than Intel Broxton.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If tcmu_handle_completions() has to process a padding shorter than
sizeof(struct tcmu_cmd_entry), the current call to
tcmu_flush_dcache_range() with sizeof(struct tcmu_cmd_entry) as length
param is wrong and causes crashes on e.g. ARM, because
tcmu_flush_dcache_range() in this case calls
flush_dcache_page(vmalloc_to_page(start)); with start being an invalid
address above the end of the vmalloc'ed area.
The fix is to use the minimum of remaining ring space and sizeof(struct
tcmu_cmd_entry) as the length param.
The patch was tested on kernel 4.19.118.
See https://bugzilla.kernel.org/show_bug.cgi?id=208045#c10
Link: https://lore.kernel.org/r/20200629093756.8947-1-bstroesser@ts.fujitsu.com Tested-by: JiangYu <lnsyyj@hotmail.com> Acked-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We make an assumption that a debugfs directory exists, but since
this can fail ensure it exists before allowing blktrace setup to
complete. Otherwise we end up stuffing blktrace files on the debugfs
root directory. In the worst case scenario this *in theory* can create
an eventual panic *iff* in the future a similarly named file is created
prior on the debugfs root directory. This theoretical crash can happen
due to a recursive removal followed by a specific dentry removal.
This doesn't fix any known crash, however I have seen the files
go into the main debugfs root directory in cases where the debugfs
directory was not created due to other internal bugs with blktrace
now fixed.
blktrace is also completely useless without this directory, so
this ensures to userspace we only setup blktrace if the kernel
can stuff files where they are supposed to go into.
debugfs directory creations typically aren't checked for, and we have
maintainers doing sweep removals of these checks, but since we need this
check to ensure proper userspace blktrace functionality we make sure
to annotate the justification for the check.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no need to try instrumenting functions in kernel/stackleak.c.
Otherwise that can cause issues if the cleanup pass of stackleak gcc plugin
is disabled.
The value av7110->debi_virt is stored in DMA memory, and it is assigned
to data, and thus data[0] can be modified at any time by malicious
hardware. In this case, "if (data[0] < 2)" can be passed, but then
data[0] can be changed into a large number, which may cause buffer
overflow when the code "av7110->ci_slot[data[0]]" is used.
To fix this possible bug, data[0] is assigned to a local variable, which
replaces the use of data[0].
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
xive_native_provision_pages() allocates memory and passes the pointer to
OPAL so kmemleak cannot find the pointer usage in the kernel memory and
produces a false positive report (below) (even if the kernel did scan
OPAL memory, it is unable to deal with __pa() addresses anyway).
projects / thirdparty / kernel / stable.git / log
