Dquots pointed to from i_dquot arrays in inodes are protected by
dquot_srcu. Annotate them as such and change .get_dquots callback to
return properly annotated pointer to make sparse happy.
Fixes: b9ba6f94b238 ("quota: remove dqptr_sem") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dquot pointers in i_dquot array in the inode are protected by
dquot_srcu. Annotate the array pointers with __rcu, perform the locked
dereferences with srcu_dereference_check() instead of plain reads, and
set the array elements with rcu_assign_pointer().
Fixes: b9ba6f94b238 ("quota: remove dqptr_sem") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402061900.rTuYDlo6-lkp@intel.com/ Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240202081852.2514092-1-wangjianjian3@huawei.com>
Stable-dep-of: 179b8c97ebf6 ("quota: Fix rcu annotations of inode dquot pointers") Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to toggle the resets in a rapid fashion can lead to the changes
not actually arriving at the clock controller block when we expect them
to. This was observed at least on SM8250.
Read back the value after regmap_update_bits to ensure write completion.
The issue arises when the array 'adev->vcn.vcn_config' is accessed
before checking if the index 'adev->vcn.num_vcn_inst' is within the
bounds of the array.
The fix involves moving the bounds check before the array access. This
ensures that 'adev->vcn.num_vcn_inst' is within the bounds of the array
before it is used as an index.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_discovery.c:1289 amdgpu_discovery_reg_base_init() error: testing array offset 'adev->vcn.num_vcn_inst' after use.
Fixes: a0ccc717c4ab ("drm/amdgpu/discovery: validate VCN and SDMA instances") Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MT8192 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: d32f38f2a8fc ("pinctrl: mediatek: Add pinctrl driver for mt8192") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240131071910.3950450-2-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MT8186 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: 8b483bda1e46 ("pinctrl: add pinctrl driver on mt8186") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240131071910.3950450-1-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dvb_register_device, *pdvbdev is set equal to dvbdev, which is freed
in several error-handling paths. However, *pdvbdev is not set to NULL
after dvbdev's deallocation, causing use-after-frees in many places,
for example, in the following call chain:
When calling dvb_unregister_device, dmxdev->dvbdev (i.e. *pdvbdev in
dvb_register_device) could point to memory that had been freed in
dvb_register_device. Thereafter, this pointer is transferred to
kref_put and triggering a use-after-free.
According to the datasheets, the ESMT chips in question will return a 5
byte long identification code where the last 3 bytes are the JEDEC
continuation codes (7Fh). Although, I would have expected 4 continuation
codes as Powerchip Semiconductor (C8h, corresponding to the parameter
page data) is located in bank 5 of the JEDEC database.
By matching the full 5 bytes we can avoid clashes with GigaDevice NAND
flashes.
This fix allows the MT7688-based GARDENA smart Gateway to boot again.
Fixes: aa08bf187f32 ("mtd: spinand: esmt: add support for F50D2G41KA") Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com> Reviewed-by: Martin Kurbanov <mmkurbanov@salutedevices.com> Tested-by: Martin Kurbanov <mmkurbanov@salutedevices.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20240125200108.24374-3-ezra@easyb.ch Signed-off-by: Sasha Levin <sashal@kernel.org>
The port@0 node doesn't define any extra properties in the port or endpoint
nodes, so the $ref should be to "/properties/port" instead as it restricts
extra properties.
Fixes: 0f82ffa9a295 ("media: dt-bindings: media: i2c: Add bindings for TW9900") Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The entity->name (i.e. name) is allocated in v4l2_m2m_register_entity
but isn't freed in its following error-handling paths. This patch
adds such deallocation to prevent memleak of entity->name.
Fixes: be2fff656322 ("media: add helpers for memory-to-memory media controller") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
In tpg_alloc, resources should be deallocated in each and every
error-handling paths, since they are allocated in for statements.
Otherwise there would be memleaks because tpg_free is called only when
tpg_alloc return 0.
Fixes: 63881df94d3e ("[media] vivid: add the Test Pattern Generator") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Static analyzers generate alerts for an unchecked call to
`media_device_register()`. However, in this case, the device will work
reliably without the media controller API.
Add a comment above the call to prevent future unnecessary changes.
When building perf with BPF skels we either copy the minimalistic
tools/perf/util/bpf_skel/vmlinux/vmlinux.h or use bpftool to generate a
vmlinux from BTF, storing the result in $(SKEL_OUT)/vmlinux.h.
We need to remove that when doing a 'make -C tools/perf clean', fix it.
Fixes: b7a2d774c9c5a9a3 ("perf build: Add ability to build with a generated vmlinux.h") Reviewed-by: Ian Rogers <irogers@google.com> Cc: Andrii Nakryiko <andrii@kernel.org> Cc: James Clark <james.clark@arm.com> Cc: Tiezhu Yang <yangtiezhu@loongson.cn> Cc: Yang Jihong <yangjihong1@huawei.com> Cc: bpf@vger.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/Zbz89KK5wHfZ82jv@x1 Signed-off-by: Sasha Levin <sashal@kernel.org>
When SPI transfer is being prepared, the spi-s3c64xx driver will call
clk_set_rate() to change the rate of SPI source clock (IPCLK). But IPCLK
is a gate (leaf) clock, so it must propagate the rate change up the
clock tree, so that corresponding DIV clocks can actually change their
divider values. Add CLK_SET_RATE_PARENT flag to corresponding clocks for
all SPI instances in Exynos850 (spi_0, spi_1 and spi_2) to make it
possible. This change involves next clocks:
usi_spi_0:
Clock Block Div range
--------------------------------------------
gout_spi0_ipclk CMU_PERI -
dout_peri_spi0 CMU_PERI /1..32
mout_peri_spi_user CMU_PERI -
dout_peri_ip CMU_TOP /1..16
usi_cmgp0:
Clock Block Div range
--------------------------------------------
gout_cmgp_usi0_ipclk CMU_CMGP -
dout_cmgp_usi0 CMU_CMGP /1..32
mout_cmgp_usi0 CMU_CMGP -
gout_clkcmu_cmgp_bus CMU_APM -
dout_apm_bus CMU_APM /1..8
usi_cmgp1:
Clock Block Div range
--------------------------------------------
gout_cmgp_usi1_ipclk CMU_CMGP -
dout_cmgp_usi1 CMU_CMGP /1..32
mout_cmgp_usi1 CMU_CMGP -
gout_clkcmu_cmgp_bus CMU_APM -
dout_apm_bus CMU_APM /1..8
With input clock of 400 MHz, this scheme provides next IPCLK rate range,
for each SPI block:
Which should cover all possible applications of SPI bus. Of course,
setting SPI frequency to values as low as 500 kHz will also affect the
common bus dividers (dout_apm_bus or dout_peri_ip), which in turn
effectively lowers the rates for all leaf bus clocks derived from those
dividers, like HSI2C and I3C clocks. But at least it gives the board
designer a choice, whether to keep all clocks (SPI/HSI2C/I3C) at high
frequencies, or make all those clocks have lower frequencies. Not
propagating the rate change to those common dividers would limit this
choice to "only high frequencies are allowed for SPI/HSI2C/I3C" option,
making the common dividers useless. This decision follows the "Worse is
better" approach, relying on the users/engineers to know the system
internals when working with such low-level features, instead of trying
to account for all possible use-cases.
Commit d3aaa7203a17 ("pinctrl: renesas: rzg2l: Add pin configuration
support for pinmux groups") introduced the possibility to parse pin
configuration for pinmux groups. It did that by calling
rzg2l_map_add_config() at the end of rzg2l_dt_subnode_to_map() and
jumping to the remove_group label in case rzg2l_map_add_config() failed.
But if that happens, the mutex will already be unlocked, thus this it will
lead to double mutex unlock operation. To fix this move the
rzg2l_map_add_config() call just after all the name argument is ready and
before the mutex is locked. There is no harm in doing this, as this only
parses the data from device tree that will be further processed by
pinctrl core code.
The fencing of MOB creation used in vmw_du_get_cursor_mob was incompatible
with register-based device communication employed by this routine. As a
result cursor MOB creation was racy, leading to potentially broken/missing
mouse cursor on desktops using CursorMob device feature.
The devm_request_irq() call is done for "dma_rt" interrupt but the error
message printed "dma_tx" interrupt on failure, fix this by updating
dma_tx -> dma_rt in dev_err_probe() message. While at it aligned the code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Fixes: 38c042b59af0248a ("ASoC: sh: rz-ssi: Update interrupt handling for half duplex channels") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://msgid.link/r/20240130150822.327434-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d71 ("drm/amd/display: add null checks before logging") Cc: Wyatt Wood <wyatt.wood@amd.com> Cc: Anthony Koo <Anthony.Koo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current method to set Channel Index when the system is missing _DSD
assumes that the channels alternate, which is not guaranteed.
Instead use the same methodology as the main driver does when _DSD
exists.
Fixes: 8c4c216db8fb ("ALSA: hda: cs35l41: Add config table to support many laptops without _DSD") Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com> Link: https://lore.kernel.org/r/20240126164005.367021-2-sbinding@opensource.cirrus.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The use of array_size() leads gcc to assume the memcpy() can have a larger
limit than actually possible, which triggers a string fortification warning:
In file included from include/linux/string.h:296,
from include/linux/bitmap.h:12,
from include/linux/cpumask.h:12,
from include/linux/sched.h:16,
from include/linux/delay.h:23,
from include/linux/iopoll.h:12,
from drivers/crypto/intel/qat/qat_common/adf_gen4_hw_data.c:3:
In function 'fortify_memcpy_chk',
inlined from 'adf_gen4_init_thd2arb_map' at drivers/crypto/intel/qat/qat_common/adf_gen4_hw_data.c:401:3:
include/linux/fortify-string.h:579:4: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
579 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/fortify-string.h:588:4: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
588 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The msr PMU is a software one, meaning msr events may be grouped
with events in a hardware context. As the msr PMU isn't marked as a
software PMU by perf_pmu__is_software, groups with the msr PMU in
are broken and the msr events placed in a different group. This
may lead to multiplexing errors where a hardware event isn't
counted while the msr event, such as tsc, is. Fix all of this by
marking the msr PMU as software, which agrees with the driver.
Before:
```
$ perf stat -e '{slots,tsc}' -a true
WARNING: events were regrouped to match PMUs
Fixes: 251aa040244a ("perf parse-events: Wildcard most "numeric" events") Signed-off-by: Ian Rogers <irogers@google.com> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Cc: James Clark <james.clark@arm.com> Cc: Caleb Biggers <caleb.biggers@intel.com> Cc: Edward Baker <edward.baker@intel.com> Cc: Perry Taylor <perry.taylor@intel.com> Cc: Samantha Alt <samantha.alt@intel.com> Cc: Weilin Wang <weilin.wang@intel.com> Link: https://lore.kernel.org/r/20240124234200.1510417-1-irogers@google.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tell snprintf() to store at most 10 bytes in the output buffer
instead of 30.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_debugfs.c:1508 dp_dsc_clock_en_read() error: snprintf() is printing too much 30 vs 10
Fixes: c06e09b76639 ("drm/amd/display: Add DSC parameters logging to debugfs") Cc: Alex Hung <alex.hung@amd.com> Cc: Qingqing Zhuo <qingqing.zhuo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous attempt to autodetect well-behaving patched firmware
introduced in commit 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw
on cptkbd and stop applying workaround") has shown that there are
false-positives on original firmware (on both 1st gen and 2nd gen
keyboards) which causes the middle button click workaround to be
mistakenly disabled.
This commit adds explicit parameter to sysfs to control this
workaround.
Fixes: 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround") Fixes: 43527a0094c1 ("HID: lenovo: Restrict detection of patched firmware only to USB cptkbd") Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pipe mode, no need to switch perf data output, therefore,
'--timestamp-filename' option should not take effect.
Check the conflict before recording and output WARNING.
In this case, the check pipe mode in perf_data__switch() can be removed.
Before:
# perf record --timestamp-filename -o- perf test -w noploop | perf report -i- --percent-limit=1
# To display the perf.data header info, please use --header/--header-only options.
#
[ perf record: Woken up 1 times to write data ]
[ perf record: Dump -.2024011812110182 ]
#
# Total Lost Samples: 0
#
# Samples: 4K of event 'cycles:P'
# Event count (approx.): 2176784359
#
# Overhead Command Shared Object Symbol
# ........ ....... .................... ......................................
#
97.83% perf perf [.] noploop
#
# (Tip: Print event counts in CSV format with: perf stat -x,)
#
After:
# perf record --timestamp-filename -o- perf test -w noploop | perf report -i- --percent-limit=1
WARNING: --timestamp-filename option is not available in pipe mode.
# To display the perf.data header info, please use --header/--header-only options.
#
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
#
# Total Lost Samples: 0
#
# Samples: 4K of event 'cycles:P'
# Event count (approx.): 2185575421
#
# Overhead Command Shared Object Symbol
# ........ ....... ..................... .............................................
#
97.75% perf perf [.] noploop
perf_data__switch() may not assign a legal value to 'new_filename'.
In this case, 'new_filename' uses the on-stack value, which may cause a
incorrect free and unexpected result.
Fixes: 03724b2e9c45 ("perf record: Allow to limit number of reported perf.data files") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240119040304.3708522-2-yangjihong1@huawei.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TLP Prefix Log Register consists of multiple DWORDs (PCIe r6.1 sec
7.9.14.13) but the loop in dpc_process_rp_pio_error() keeps reading from
the first DWORD, so we print only the first PIO TLP Prefix (duplicated
several times), and we never print the second, third, etc., Prefixes.
Add the iteration count based offset calculation into the config read.
Since commit 1029939b3782 ("media: v4l: async: Simplify async sub-device fwnode matching"),
async connections are matched using the async sub-device fwnode, not that
of the endpoint. Fix this by using the fwnode of the connection match to
find the pad.
Fixes: 1029939b3782 ("media: v4l: async: Simplify async sub-device fwnode matching") Signed-off-by: Julien Massot <julien.massot@collabora.com> Reviewed-by: Jai Luthra <j-luthra@ti.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just T210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes 210 you don't get
this driver.
Fixes: 433de642a76c9 ("dmaengine: tegra210-adma: add support for Tegra186/Tegra194") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Cc: Sameer Pujar <spujar@nvidia.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20240112093310.329642-2-pbrobinson@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version fallback if
firmware files are missing") changed the order of some operations and
the firmware paths are not available anymore at snd_sof_probe() time.
Precisely, fw_filename_prefix is set by sof_select_ipc_and_paths() via
but sof_init_environment() which calls this function was moved from
snd_sof_device_probe() to sof_probe_continue(). Moreover,
snd_sof_probe() was moved from sof_probe_continue() to
sof_init_environment(), but before the call to
sof_select_ipc_and_paths().
The problem here is that amd_sof_acp_probe() uses fw_filename_prefix to
compute fw_code_bin and fw_data_bin paths, and because the field is not
yet initialized, the paths end up containing (null):
snd_sof_amd_vangogh 0000:04:00.5: Direct firmware load for (null)/sof-vangogh-code.bin failed with error -2
snd_sof_amd_vangogh 0000:04:00.5: sof signed firmware code bin is missing
snd_sof_amd_vangogh 0000:04:00.5: error: failed to load DSP firmware -2
snd_sof_amd_vangogh: probe of 0000:04:00.5 failed with error -2
Move usage of fw_filename_prefix right before request_firmware() calls
in acp_sof_load_signed_firmware().
Fixes: 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version fallback if firmware files are missing") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Link: https://msgid.link/r/20231219030728.2431640-9-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ACP driver for Vangogh platform uses a quirk for Valve Galileo
device to setup a custom firmware loader, which neither requires nor
uses the firmware file indicated via the default_fw_filename member of
struct sof_dev_desc.
Since commit 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version
fallback if firmware files are missing"), the provided filename gets
verified and triggers a fatal error on probe:
[ 7.719337] snd_sof_amd_vangogh 0000:04:00.5: enabling device (0000 -> 0002)
[ 7.721486] snd_sof_amd_vangogh 0000:04:00.5: SOF firmware and/or topology file not found.
[ 7.721565] snd_sof_amd_vangogh 0000:04:00.5: Supported default profiles
[ 7.721569] snd_sof_amd_vangogh 0000:04:00.5: - ipc type 0 (Requested):
[ 7.721573] snd_sof_amd_vangogh 0000:04:00.5: Firmware file: amd/sof/sof-vangogh.ri
[ 7.721577] snd_sof_amd_vangogh 0000:04:00.5: Topology file: amd/sof-tplg/sof-vangogh-nau8821-max.tplg
[ 7.721582] snd_sof_amd_vangogh 0000:04:00.5: Check if you have 'sof-firmware' package installed.
[ 7.721585] snd_sof_amd_vangogh 0000:04:00.5: Optionally it can be manually downloaded from:
[ 7.721589] snd_sof_amd_vangogh 0000:04:00.5: https://github.com/thesofproject/sof-bin/
[ 7.721997] snd_sof_amd_vangogh: probe of 0000:04:00.5 failed with error -2
According to AMD, a combined ".ri" file which includes the code and data
segments cannot be used due to a limitation preventing the code image to
be signed on build time.
Fix the issue by skipping the firmware file test if a custom loader is
being used instead of the generic one.
Fixes: 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version fallback if firmware files are missing") Co-developed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Link: https://msgid.link/r/20231219030728.2431640-8-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver uses kasprintf() to initialize fw_{code,data}_bin members of
struct acp_dev_data, but kfree() is never called to deallocate the
memory, which results in a memory leak.
Fix the issue by switching to devm_kasprintf(). Additionally, ensure the
allocation was successful by checking the pointer validity.
Fixes: f7da88003c53 ("ASoC: SOF: amd: Enable signed firmware image loading for Vangogh platform") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Link: https://msgid.link/r/20231219030728.2431640-6-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Handle potential acp_sofdsp_dai_links_create() errors in ACP SOF machine
driver's probe function. Note there is no need for an undo.
While at it, switch to dev_err_probe().
Fixes: 9f84940f5004 ("ASoC: amd: acp: Add SOF audio support on Chrome board") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Link: https://msgid.link/r/20231219030728.2431640-4-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some edp panel requires T10 (Delay from end of valid video data transmitted
by the Source device to power-off) less than 500ms. Using autosuspend with
delay set as 1000 violates this requirement.
Use put_sync_suspend in unprepare to meet the spec. For other cases (such
as getting EDID), it still uses autosuspend.
Suggested-by: Douglas Anderson <dianders@chromium.org> Fixes: 3235b0f20a0a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20231220221418.2610185-1-hsinyi@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
This scary message can misled the user into thinking something bad has
happened and needs to be fixed, however it could simply be part of a
normal boot process where EPROBE_DEFER is taken into account. Therefore,
let's use dev_err_probe so that this message doesn't get shown (by
default) when the return code is EPROBE_DEFER.
ret variable stores the return value of drm_of_find_panel_or_bridge
which can return error codes different from EPROBE_DEFER. Therefore,
let's just return that error code instead of forcing it to EPROBE_DEFER.
When the floor LUT index (drm_fixp2int(lut_index) is the last
index of the array the ceil LUT index will point to an entry
beyond the array. Make sure we guard against it and use the
value of the floor LUT index.
v3:
- Drop bits from commit description that didn't contribute
anything of value
Fixes: db1f254f2cfa ("drm/vkms: Add support to 1D gamma LUT") Signed-off-by: Harry Wentland <harry.wentland@amd.com> Cc: Arthur Grillo <arthurgrillo@riseup.net> Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net> Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231108163647.106853-6-harry.wentland@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Unit testing this in VKMS shows that passing 0 into
this function returns -1, which is highly counter-
intuitive. Fix it by checking whether the input is
>= 0 instead of > 0.
Fixes: 64566b5e767f ("drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil") Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Simon Ser <contact@emersion.fr> Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231108163647.106853-2-harry.wentland@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller wants the difference between *total and *sync_start in the
HDMI_VIDEO_EXT_*DELAY registers. Otherwise the signal is very unstable for
certain non-VIC modes. See downstream commit [0].
The pm_runtime_enable function increases the power disable depth,
which means that we must perform a matching decrement on the error
handling path to maintain balance within the given context.
Additionally, we need to address the same issue for pm_runtime_get_sync.
We fix this by invoking pm_runtime_disable and pm_runtime_put_sync
when error returns.
When the power domains cannot be parsed, the message is incorrectly
logged as an info message. Let's change this to an error since an error
is returned.
Fixes: 92a511a568e4 ("fbdev/simplefb: Add support for generic power-domains") Signed-off-by: Brian Masney <bmasney@redhat.com> Acked-by: Andrew Halaney <ahalaney@redhat.com> Acked-by: Javier Martinez Canillas <javierm@redhat.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231212195754.232303-1-bmasney@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is this reported crash when experimenting with the lvm2 testsuite.
The list corruption is caused by the fact that the postsuspend and resume
methods were not paired correctly; there were two consecutive calls to the
origin_postsuspend function. The second call attempts to remove the
"hash_list" entry from a list, while it was already removed by the first
call.
Fix __dm_internal_resume so that it calls the preresume and resume
methods of the table's targets.
If a preresume method of some target fails, we are in a tricky situation.
We can't return an error because dm_internal_resume isn't supposed to
return errors. We can't return success, because then the "resume" and
"postsuspend" methods would not be paired correctly. So, we set the
DMF_SUSPENDED flag and we fake normal suspend - it may confuse userspace
tools, but it won't cause a kernel crash.
An empty flush doesn't have a payload, so it should never be looked at
when considering to possibly requeue a bio for the case when a reshape
is in progress.
Fixes: 9dbd1aa3a81c ("dm raid: add reshaping support to the target") Reported-by: Patrick Plenefisch <simonpatp@gmail.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some architectures like ARM64, PMD_SIZE can be really large in some
configurations. Like with CONFIG_ARM64_64K_PAGES=y the PMD_SIZE is
512MB.
Use 2MB * num_possible_nodes() as the size for allocations done through
the prog pack allocator. On most architectures, PMD_SIZE will be equal
to 2MB in case of 4KB pages and will be greater than 2MB for bigger page
sizes.
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d031140 ("nfp: flower: monitor and offload LAG groups") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the unknown device, rtl8152_cfgselector_choose_configuration()
should return a negative value. Then, usb_choose_configuration() would
set a configuration for CDC ECM or NCM mode. Otherwise, there is no
usb interface driver for the device.
Fixes: aa4f2b3e418e ("r8152: Choose our USB config with choose_configuration() rather than probe()") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Link: https://lore.kernel.org/r/20240308075206.33553-436-nic_swsd@realtek.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set eswitch inline-mode to be u8, not u16. Otherwise, errors below
$ devlink dev eswitch set pci/0000:08:00.0 mode switchdev \
inline-mode network
Error: Attribute failed policy validation.
kernel answers: Numerical result out of rang
netlink: 'devlink': attribute type 26 has an invalid length.
Fixes: f2f9dd164db0 ("netlink: specs: devlink: add the remaining command to generate complete split_ops") Signed-off-by: William Tu <witu@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240310164547.35219-1-witu@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 3557baabf280 ("[L2TP]: PPP over L2TP driver core") Reviewed-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'olr' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'olr' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the kernel isn't built with interconnect support, icc_get_name()
returns NULL and we get following warning:
drivers/opp/debugfs.c: In function 'bw_name_read':
drivers/opp/debugfs.c:43:42: error: '%.62s' directive argument is null [-Werror=format-overflow=]
i = scnprintf(buf, sizeof(buf), "%.62s\n", icc_get_name(path));
Fix it.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402141313.81ltVF5g-lkp@intel.com/ Fixes: 0430b1d5704b0 ("opp: Expose bandwidth information via debugfs") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is because the file_system_type of both erofs and the pseudo-mount
point of domain_id is erofs_fs_type, so two successive calls to
alloc_super() are considered to be using the same lock and trigger the
warning above.
Therefore add a nodev file_system_type called erofs_anon_fs_type in
fscache.c to silence this complaint. Because kern_mount() takes a
pointer to struct file_system_type, not its (string) name. So we don't
need to call register_filesystem(). In addition, call init_pseudo() in
erofs_anon_init_fs_context() as suggested by Al Viro, so that we can
remove erofs_fc_fill_pseudo_super(), erofs_fc_anon_get_tree(), and
erofs_anon_context_ops.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Fixes: a9849560c55e ("erofs: introduce a pseudo mnt to manage shared cookies") Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-and-tested-by: Jingbo Xu <jefflexu@linux.alibaba.com> Reviewed-by: Yang Erkun <yangerkun@huawei.com> Link: https://lore.kernel.org/r/20240307101018.2021925-1-libaokun1@huawei.com Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay") Signed-off-by: Tim Pambor <tp@osasysteme.de> Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Section 1.2 of Core Specification Supplement Part A the
complete or short name strings are defined as utf8s, which should not
include the trailing NULL for variable length array as defined in Core
Specification Vol1 Part E Section 2.9.3.
Removing the trailing NULL allows PTS to retrieve the random address based
on device name, e.g. for SM/PER/KDU/BV-02-C, SM/PER/KDU/BV-08-C or
GAP/BROB/BCST/BV-03-C.
Fixes: f61851f64b17 ("Bluetooth: Fix append max 11 bytes of name to scan rsp data") Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the mac port is fixed to configured as full dplex mode in
hclge_mac_init() when driver initialization or reset restore. Users may
change the mode to half duplex with ethtool, so it may cause the user
configuration dropped after reset.
To fix it, don't change the duplex mode when resetting.
Fixes: 2d03eacc0b7e ("net: hns3: Only update mac configuation when necessary") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HIP08 devices does not register the ptp devices, so the
hdev->ptp is NULL, but the hardware can receive 1588 messages,
and set the HNS3_RXD_TS_VLD_B bit, so, if match this case, the
access of hdev->ptp->flags will cause a kernel crash:
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In hns3_dcbnl_ieee_delapp, should check ieee_delapp not ieee_setapp.
This path fix the wrong judgment.
Fixes: 0ba22bcb222d ("net: hns3: add support config dscp map to tc") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, if there are multiple registrations of the same pin on the
same dpll device, following warnings are observed:
WARNING: CPU: 5 PID: 2212 at drivers/dpll/dpll_core.c:143 dpll_xa_ref_pin_del.isra.0+0x21e/0x230
WARNING: CPU: 5 PID: 2212 at drivers/dpll/dpll_core.c:223 __dpll_pin_unregister+0x2b3/0x2c0
The problem is, that in both dpll_xa_ref_dpll_del() and
dpll_xa_ref_pin_del() registration is only removed from list in case the
reference count drops to zero. That is wrong, the registration has to
be removed always.
To fix this, remove the registration from the list and free
it unconditionally, instead of doing it only when the ref reference
counter reaches zero.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions") Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay") Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Devlink param for adjusting NPC MCAM high zone
area is in wrong param list and is not getting
activated on CN10KA silicon.
That patch fixes this issue.
Fixes: dd7842878633 ("octeontx2-af: Add new devlink param to configure maximum usable NIX block LFs") Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
8d975c15c0cd ("ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()") 1ca1ba465e55 ("geneve: make sure to pull inner header in geneve_rx()")
We have to save skb->network_header in a temporary variable
in order to be able to recompute the network_header pointer
after a pskb_inet_may_pull() call.
pskb_inet_may_pull() makes sure the needed headers are in skb->head.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When rule policy is changed, ipv6 socket cache is not refreshed.
The sock's skb still uses a outdated route cache and was sent to
a wrong interface.
To avoid this error we should update fib node's version when
rule is changed. Then skb's route will be reroute checked as
route cache version is already different with fib node version.
The route cache is refreshed to match the latest rule.
Fixes: 101367c2f8c4 ("[IPV6]: Policy Routing Rules") Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com> Signed-off-by: Lena Wang <lena.wang@mediatek.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the kernel is comiled with CONFIG_IRQ_REMAP=y but without
CONFIG_IOMMU_INTEL compilation fails since commit def054b01a8678 with an
undefined reference to device_rbtree_find(). This patch makes sure that
intel specific code is only compiled with CONFIG_IOMMU_INTEL=y.
The stackmap code relies on roundup_pow_of_two() to compute the number
of hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code.
The commit in the fixes tag actually attempted to fix this, but the fix
did not account for the UB, so the fix only works on CPUs where an
overflow does result in a neat truncation to zero, which is not
guaranteed. Checking the value before rounding does not have this
problem.
Fixes: 6183f4d3a0a2 ("bpf: Check for integer overflow when using roundup_pow_of_two()") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-ID: <20240307120340.99577-4-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hashtab code relies on roundup_pow_of_two() to compute the number of
hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code. So apply the same
fix to hashtab, by moving the overflow check to before the roundup.
Fixes: daaf427c6ab3 ("bpf: fix arraymap NULL deref and missing overflow and zero size checks") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-3-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devmap code allocates a number hash buckets equal to the next power
of two of the max_entries value provided when creating the map. When
rounding up to the next power of two, the 32-bit variable storing the
number of buckets can overflow, and the code checks for overflow by
checking if the truncated 32-bit value is equal to 0. However, on 32-bit
arches the rounding up itself can overflow mid-way through, because it
ends up doing a left-shift of 32 bits on an unsigned long value. If the
size of an unsigned long is four bytes, this is undefined behaviour, so
there is no guarantee that we'll end up with a nice and tidy 0-value at
the end.
Syzbot managed to turn this into a crash on arm32 by creating a
DEVMAP_HASH with max_entries > 0x80000000 and then trying to update it.
Fix this by moving the overflow check to before the rounding up
operation.
Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index") Link: https://lore.kernel.org/r/000000000000ed666a0611af6818@google.com Reported-and-tested-by: syzbot+8cd36f6b65f3cafd400a@syzkaller.appspotmail.com Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-2-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit 36bbc5b4ffab ("cacheinfo: Allow early detection and population
of cache attributes") the shared cpu list for each cache level higher than
L1 is rebuilt even if the list already has been set up.
This is caused by the removal of the cpumask_empty() check within
cache_shared_cpu_map_setup().
However architectures can enforce that the shared cpu list is not rebuilt
by simply setting cpu_map_populated of the per cpu cache info structure to
true, which is also the fix for this problem.
Fixes: 36bbc5b4ffab ("cacheinfo: Allow early detection and population of cache attributes") Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Attemting to do sock_lock on .recvmsg may cause a deadlock as shown
bellow, so instead of using sock_sock this uses sk_receive_queue.lock
on bt_sock_ioctl to avoid the UAF:
This checks if CONFIG_DEV_COREDUMP is enabled before attempting to clone
the skb and also make sure btmtk_process_coredump frees the skb passed
following the same logic.
Fixes: 0b7015132878 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
struct hci_dev_info has a fixed size name[8] field so in the event that
hdev->name is bigger than that strcpy would attempt to write past its
size, so this fixes this problem by switching to use strscpy.
Fixes: dcda165706b9 ("Bluetooth: hci_core: Fix build warnings") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The problem is detected by KASAN.
btrtl driver uses private hci data to store 'struct btrealtek_data'.
If btrtl driver is used with btusb, then memory for private hci data
is allocated in btusb. But no private data is allocated after hci_dev,
when btrtl is used with hci_h5.
This commit adds memory allocation for hci_h5 case.
==================================================================
BUG: KASAN: slab-out-of-bounds in btrtl_initialize+0x6cc/0x958 [btrtl]
Write of size 8 at addr ffff00000f5a5748 by task kworker/u9:0/76
In a few cases the stack may generate commands as responses to events
which would happen to overwrite the sent_cmd, so this attempts to store
the request in req_skb so even if sent_cmd is replaced with a new
command the pending request will remain in stored in req_skb.
Fixes: 6a98e3836fa2 ("Bluetooth: Add helper for serialized HCI command execution") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
