Considering that we can not offline all cpus in any cases,
we need to reserve one cpu online when the test offline all
hotpluggable online cpus, otherwise the test will fail forever.
Fixes: d89dffa976bc ("fault-injection: add selftests for cpu and memory hotplug") Signed-off-by: Zhao Gongyi <zhaogongyi@huawei.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This crash is a result of iomap_writepage_map encountering some sort of
error during writeback and wanting to set that error code in the file
mapping so that fsync will report it. Unfortunately, the code
dereferences folio->mapping after unlocking the folio, which means that
another thread could have removed the page from the page cache
(writeback doesn't hold the invalidation lock) and give it to somebody
else.
At best we crash the system like above; at worst, we corrupt memory or
set an error on some other unsuspecting file while failing to record the
problems with *this* file. Regardless, fix the problem by reporting the
error to the inode mapping.
NOTE: Commit 598ecfbaa742 lifted the XFS writeback code to iomap, so
this fix should be backported to XFS in the 4.6-5.4 kernels in addition
to iomap in the 5.5-5.19 kernels.
Fixes: e735c0079465 ("iomap: Convert iomap_add_to_ioend() to take a folio") # 5.17 onward Fixes: 598ecfbaa742 ("iomap: lift the xfs writeback code to iomap") # 5.5-5.16, needs backporting Fixes: 150d5be09ce4 ("xfs: remove xfs_cancel_ioend") # 4.6-5.4, needs backporting Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
EHCI Oxynos (drivers/usb/host/ehci-exynos.c) drives VBUS GPIO high when
trying to power up the bus, therefore the GPIO in DTS must be marked as
"active high". This will be important when EHCI driver is converted to
gpiod API that respects declared polarities.
Fixes: 4e8991def565 ("ARM: dts: exynos: Enable AX88760 USB hub on Origen board") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Link: https://lore.kernel.org/r/20220927220504.3744878-1-dmitry.torokhov@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to s3fwrn5 driver code the "enable" GPIO line is driven "high"
when chip is not in use (mode is S3FWRN5_MODE_COLD), and is driven "low"
when chip is in use.
When a module PLTs are used and a module is loaded sufficiently far away
from the kernel, we'll create PLTs for any branches which are
out-of-range. These are separate from the special ftrace trampoline
PLTs, which the module PLT code doesn't directly manipulate.
When mcount is in use this is a problem, as each mcount callsite in a
module will be initialized to point to a module PLT, but since commit a6253579977e4c6f ftrace_make_nop() will assume that the callsite has
been initialized to point to the special ftrace trampoline PLT, and
ftrace_find_callable_addr() rejects other cases.
This means that when ftrace tries to initialize a callsite via
ftrace_make_nop(), the call to ftrace_find_callable_addr() will find
that the `_mcount` stub is out-of-range and is not handled by the ftrace
PLT, resulting in a splat:
Fix this by reverting to the old behaviour of ignoring the old
instruction when initialising an mcount callsite in a module, which was
the behaviour prior to commit a6253579977e4c6f.
On a read-only filesystem, we won't invoke the block allocator, so we
don't need to prefetch the block bitmaps.
This avoids starting and running the ext4lazyinit thread at all on a
system with no read-write ext4 filesystems (for instance, a container VM
with read-only filesystems underneath an overlayfs).
When expanding a file system from (16TiB-2MiB) to 18TiB, the operation
exits early which leads to result inconsistency between resize2fs and
Ext4 kernel driver.
=== before ===
○ → resize2fs /dev/mapper/thin
resize2fs 1.45.5 (07-Jan-2020)
Filesystem at /dev/mapper/thin is mounted on /mnt/test; on-line resizing required
old_desc_blocks = 2048, new_desc_blocks = 2304
The filesystem on /dev/mapper/thin is now 4831837696 (4k) blocks long.
[ 865.186308] EXT4-fs (dm-5): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[ 912.091502] dm-4: detected capacity change from 34359738368 to 38654705664
[ 970.030550] dm-5: detected capacity change from 34359734272 to 38654701568
[ 1000.012751] EXT4-fs (dm-5): resizing filesystem from 4294966784 to 4831837696 blocks
[ 1000.012878] EXT4-fs (dm-5): resized filesystem to 4294967296
=== after ===
[ 129.104898] EXT4-fs (dm-5): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[ 143.773630] dm-4: detected capacity change from 34359738368 to 38654705664
[ 198.203246] dm-5: detected capacity change from 34359734272 to 38654701568
[ 207.918603] EXT4-fs (dm-5): resizing filesystem from 4294966784 to 4831837696 blocks
[ 207.918754] EXT4-fs (dm-5): resizing filesystem from 4294967296 to 4831837696 blocks
[ 207.918758] EXT4-fs (dm-5): Converting file system to meta_bg
[ 207.918790] EXT4-fs (dm-5): resizing filesystem from 4294967296 to 4831837696 blocks
[ 221.454050] EXT4-fs (dm-5): resized to 4658298880 blocks
[ 227.634613] EXT4-fs (dm-5): resized filesystem to 4831837696
On arm32, the configuration options to specify the kernel command line
type depend on ATAGS. However, the actual CMDLINE cofiguration option
does not depend on ATAGS, and the code that handles this is not specific
to ATAGS (see drivers/of/fdt.c:early_init_dt_scan_chosen()).
Hence users who desire to override the kernel command line on arm32 must
enable support for ATAGS, even on a pure-DT system. Other architectures
(arm64, loongarch, microblaze, nios2, powerpc, and riscv) do not impose
such a restriction.
Hence drop the dependency on ATAGS.
Fixes: bd51e2f595580fb6 ("ARM: 7506/1: allow for ATAGS to be configured out when DT support is selected") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to s5k6a3 driver code, the reset line for the chip appears to
be active low. This also matches the typical polarity of reset lines in
general. Let's fix it up as having correct polarity in DTS is important
when the driver will be switched over to gpiod API.
Range size of 0x2b4 was incorrect since there isn't 173 configurable
pins for muxing. Additionally there is a non-addressable region in the
mapping which requires splitting into two ranges.
main_pmx0 -> 67 pins
main_pmx1 -> 3 pins
Fixes: d361ed88455f ("arm64: dts: ti: Add support for J7200 SoC") Signed-off-by: Matt Ranostay <mranostay@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Vaishnav Achath <vaishnav.a@ti.com> Link: https://lore.kernel.org/r/20220919205723.8342-1-mranostay@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The size of the UFS PHY serdes register region is 0x1c4 and the
corresponding 'reg' property should specifically not include the
adjacent regions that are defined in the child node (e.g. tx and rx).
The size of the PCIe PHY serdes register region is 0x1c4 and the
corresponding 'reg' property should specifically not include the
adjacent regions that are defined in the child node (e.g. tx and rx).
The DMA subsystem could be entirely disabled in Kconfig and then the
TEGRA20_APB_DMA option isn't available too. Hence kernel configuration
fails if DMADEVICES Kconfig option is disabled due to the unsatisfiable
dependency.
The FUSE driver isn't a critical driver and currently it only provides
NVMEM interface to userspace which isn't known to be widely used, and
thus, it's fine if FUSE driver fails to load.
Let's remove the erroneous Kconfig dependency and let the FUSE driver to
fail the probing if DMA is unavailable.
In this function, of_find_matching_node() will return a node pointer
with refcount incremented. We should use of_node_put() when the "np"
pointer is not used anymore.
Use the correct names for scl-gpios and sda-gpios so that the generic
i2c recovery code will find them. While we're here set the
GPIO_OPEN_DRAIN flag on the gpios.
Fixes: b795fadfc46b ("arm64: dts: marvell: Add Armada 98DX2530 SoC and RD-AC5X board") Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both the Linkstation LS-CHLv2 and the LS-XHL have only one ethernet
port. This has always been wrong, i.e. the board code used to set up
both ports, but the driver will play nice and return -ENODEV if the
assiciated PHY is not found. Nevertheless, it is wrong. Remove it.
Fixes: 876e23333511 ("ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 327e15428977 ("ARM: dts: kirkwood: consolidate common pinctrl
settings") unknowingly broke the serial output on this board. Before
this commit, the pinmux was still configured by the bootloader and the
kernel didn't reconfigured it again. This was an oversight by the
initial board support where the pinmux for the serial line was never
configured by the kernel. But with this commit, the serial line will be
reconfigured to the wrong pins. This is especially confusing, because
the output still works, but the input doesn't. Presumingly, the input is
reconfigured to MPP10, but the output is connected to both MPP11 and
MPP5.
Override the pinmux in the board device tree.
Fixes: 327e15428977 ("ARM: dts: kirkwood: consolidate common pinctrl settings") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a bug in Turris Omnia's schematics, whereupon the MPP[26] pin,
which is routed to CN11 pin header, is documented as SPI CS1, but
MPP[26] pin does not support this function. Instead it controls chip
select 2 if in "spi0" mode.
Fix the name of the pin node in pinctrl node and fix the comment in SPI
node.
Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia") Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's still a thermal zone using pm6150_adc in the pm6150.dtsi file,
pm6150_thermal. It's not super obvious because it indirectly uses the
adc through an iio channel in pm6150_temp. Let's keep this enabled on
lazor and coachz so that reading the temperature of the pm6150_thermal
zone continues to work. Otherwise we get -EINVAL when reading the zone,
and I suspect the PMIC temperature trip doesn't work properly so we
don't shutdown when the PMIC overheats.
The PWM is a part of the SPMI PMIC block and maps several different
addresses within the SPMI block. It is not accurate to describe as pwm@reg
as a result.
Do not allow the RPMh regulators to switch to low-power mode with an
exception for the UFS regulators (l3c, l6c, l10c and l17c) as UFS
supports an idle mode.
This specifically avoids having regulators be but in low-power mode when
only some consumers specify loads while the actual total load really
warrants high-power mode.
Do not allow the RPMh regulators to switch to low-power mode.
This specifically avoids having regulators be but in low-power mode when
only some consumers specify loads while the actual total load really
warrants high-power mode.
Do not allow the RPMh regulators to switch to low-power mode with an
exception for the UFS regulators (l7c and l3d) as UFS supports an idle
mode.
This specifically avoids having regulators be but in low-power mode when
only some consumers specify loads while the actual total load really
warrants high-power mode.
i2c2 is routed to the pins dedicated as DDC in the module standard.
Reduce clock rate to 100kHz to be in line with VESA standard and hook
this bus up to the HDMI node.
In qcom_smem_state_register() and qcom_smem_state_release(), we
should better use of_node_get() and of_node_put() for the reference
creation and destruction of 'device_node'.
Fixes: 9460ae2ff308 ("soc: qcom: Introduce common SMEM state machine code") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220721135217.1301039-2-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two refcount leak bugs in qcom_smsm_probe():
(1) The 'local_node' is escaped out from for_each_child_of_node() as
the break of iteration, we should call of_node_put() for it in error
path or when it is not used anymore.
(2) The 'node' is escaped out from for_each_available_child_of_node()
as the 'goto', we should call of_node_put() for it in goto target.
Thread A trying to acquire a write lease checks the value of i_readcount
and i_writecount in check_conflicting_open() to verify that its own fd
is the only fd referencing the file.
Thread B trying to open the file for read will call break_lease() in
do_dentry_open() before incrementing i_readcount, which leaves a small
window where thread A can acquire the write lease and then thread B
completes the open of the file for read without breaking the write lease
that was acquired by thread A.
Fix this race by incrementing i_readcount before checking for existing
leases, same as the case with i_writecount.
Use a helper put_file_access() to decrement i_readcount or i_writecount
in do_dentry_open() and __fput().
Fixes: 387e3746d01c ("locks: eliminate false positive conflicts for write lease") Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should add the of_node_put() when breaking out of
for_each_child_of_node() as it will automatically increase
and decrease the refcount.
Fixes: e6b42eb6a66c ("memory: emif: add device tree support to emif driver") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220719085640.1210583-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The break of for_each_available_child_of_node() needs a
corresponding of_node_put() when the reference 'child' is not
used anymore. Here we do not need to call of_node_put() in
fail path as '!match' means no break.
While the of_platform_device_create() will created a new
reference by 'child' but it has considered the refcounting.
Fixes: fee10bd22678 ("memory: pl353: Add driver for arm pl353 static memory controller") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220716031324.447680-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The HDMI driver skips the notification handling from the graphics
driver when the codec driver is being in the PM operation. This
behavior was introduced by the commit eb399d3c99d8 ("ALSA: hda - Skip
ELD notification during PM process"). This skip may cause a problem,
as we may miss the ELD update when the connection/disconnection
happens right at the runtime-PM operation of the audio codec.
Although this workaround was valid at that time, it's no longer true;
the fix was required just because the ELD update procedure needed to
wake up the audio codec, which had lead to a runtime-resume during a
runtime-suspend. Meanwhile, the ELD update procedure doesn't need a
codec wake up any longer since the commit 788d441a164c ("ALSA: hda -
Use component ops for i915 HDMI/DP audio jack handling"); i.e. there
is no much reason for skipping the notification.
Let's drop those checks for addressing the missing notification.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of mt6660_i2c_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm5102_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm5110_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of wm8997_probe
This reverts commit ddea4bbf287b6028eaa15a185d0693856956ecf2 ("ASoC:
wcd-mbhc-v2: use pm_runtime_resume_and_get()"), because it introduced
double runtime PM put if pm_runtime_get_sync() returns -EACCES:
The commit claimed no changes in functionality except dropping the
reference on -EACCESS. This is exactly the change introducing bug
because function calls unconditionally pm_runtime_put_autosuspend() at
the end.
Fixes: ddea4bbf287b ("ASoC: wcd-mbhc-v2: use pm_runtime_resume_and_get()") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220929131528.217502-1-krzysztof.kozlowski@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of stm32_i2s_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of stm32_spdifrx_probe.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by moving
pm_runtime_enable to the endding of stm32_adfsdm_probe.
Fixes:98e500a12f934 ("ASoC: stm32: dfsdm: add pm_runtime support for audio")
If clk_hw_register() fails, the corresponding clk should not be
unregistered.
To handle errors from loops, clean up partial iterations before doing the
goto. So add a clk_hw_unregister().
Then use a while (--i >= 0) loop in the unwind section.
Fixes: 78013a1cf297 ("ASoC: da7219: Fix clock handling around codec level probe") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/e4acceab57a0d9e477a8d5890a45c5309e553e7c.1663875789.git.christophe.jaillet@wanadoo.fr Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
tx_macro_tx_mixer_put() and tx_macro_dec_mode_put() currently returns zero
eventhough it changes the value.
Fix this, so that change notifications are sent correctly.
Fixes: d207bdea0ca9 ("ASoC: codecs: lpass-tx-macro: add dapm widgets and route") Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220906170112.1984-6-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the copy of the description string from userspace fails, then the page
for the instance descriptor doesn't get freed before returning -EFAULT,
which leads to a memleak.
The allocated ida needs to be freed up if the IPC message fails since
next time when we try again to set up the widget we are going to try to
allocate another ID and given enough tries, we are going to run out of
unique IDs.
Fixes: 711d0427c713 ("ASoC: SOF: ipc4-topology: move ida allocate/free to widget_setup/free") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220921112751.9253-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We fixed the bug introduced by the patch for managing the shared
clocks at the commit 809f44a0cc5a ("ALSA: usb-audio: Clear fixed clock
rate at closing EP"), but it was merely a workaround. By this change,
the clock reference rate is cleared at each EP close, hence the still
remaining EP may need a re-setup of rate unnecessarily.
This patch introduces the proper refcounting for the clock reference
object so that the clock setup is done only when needed.
Fixes: 809f44a0cc5a ("ALSA: usb-audio: Clear fixed clock rate at closing EP") Fixes: c11117b634f4 ("ALSA: usb-audio: Refcount multiple accesses on the single clock") Link: https://lore.kernel.org/r/20220920181126.4912-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Track the converters handling the silent stream using a new
variable to avoid mixing of the open/close and silent stream
use. This change ensures the proper allocation of the converters.
Fixes: 5f80d6bd2b01 ("ALSA: hda/hdmi: Fix the converter reuse for the silent stream") Signed-off-by: Jaroslav Kysela <perex@perex.cz> Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20220919135444.3554982-1-perex@perex.cz Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
At current implementation there is an extra 0 at 1.62G link rate which
cause no correct pixel_div selected for 1.62G link rate to calculate
mvid and nvid. This patch delete the extra 0 to have mvid and nvid be
calculated correctly.
Changes in v2:
-- fix Fixes tag's text
Changes in v3:
-- fix misspelling of "Reviewed-by"
Fixes: 937f941ca06f ("drm/msm/dp: Use qmp phy for DP PLL and PHY") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499328/ Link: https://lore.kernel.org/r/1661372150-3764-1-git-send-email-quic_khsieh@quicinc.com
[DB: rewrapped commit message] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove loops over hw_vbif. Instead always VBIF's idx as an index in the
array. This fixes an error in dpu_kms_hw_init(), where we fill
dpu_kms->hw_vbif[i], but check for an error pointer at
dpu_kms->hw_vbif[vbif_idx].
The commit 6874f48bb8b0 ("drm/msm: make mdp5/dpu devices master
components") changed the MDP5 driver to look for the interconnect paths
in the MDSS device rather than in the MDP5 device itself. This was left
unnoticed since on my testing devices the interconnects probably didn't
reach the sync state.
Rather than just using the MDP5 device for ICC path lookups for the MDP5
devices, introduce an additional helper to check both MDP5/DPU and MDSS
nodes. This will be helpful for the MDP5->DPU conversion, since the
driver will have to check both nodes.
In eukrea_tlv320_probe(), we need to hold the reference returned
from of_find_compatible_node() which has increased the refcount
and then call of_node_put() with it when done.
Fixes: 66f232908de2 ("ASoC: eukrea-tlv320: Add DT support.") Co-authored-by: Kelin Wang <wangkelin2023@163.com> Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220914134354.3995587-1-windhl@126.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use regmap_read_poll_timeout to poll I2S_CLR.
It also fixes the 'rockchip-i2s ff070000.i2s; fail to clear' when
the read of I2S_CLR exceeds the retry limit.
Fixes: 0ff9f8b9f592 ("ASoC: rockchip: i2s: Fix error code when fail to read I2S_CLR") Signed-off-by: Judy Hsiao <judyhsiao@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Link: https://lore.kernel.org/r/20220914031234.2250298-1-judyhsiao@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If construction of the array of work queues to handle hpd_rx_irq offload
work fails, we need to unwind. Destroy all the created workqueues and
the allocated memory for the hpd_rx_irq_offload_work_queue struct array.
Fixes: 8e794421bc98 ("drm/amd/display: Fork thread to offload work of hpd_rx_irq") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dss_init_ports() and __dss_uninit_ports(), we should call
of_node_put() for the reference returned by of_graph_get_port_by_id()
in fail path or when it is not used anymore.
Adding a probe callback on this snd_soc_card is required when
Sound Open Firmware support is desired, as we need to appropriately
populate the stream_name for SOF to be able to bind widgets.
Failing to do so will produce errors when applying the SOF topology
leading to card registration failure (so, no sound).
While at it, also make sure to fill the topology_shortname as required.
VGA_IS1_RC is the color mode register (VGA_IS1_RM the one for monochrome
mode, note C vs. M at the end). So when using VGA_IS1_RC make sure the
vga device is actually in color mode and set the corresponding bit in the
misc register.
Reproducible when booting VMs in UEFI mode with some edk2 versions (edk2
fix is on the way too). Doesn't happen in BIOS mode because in that
case the vgabios already flips the bit.
The recent fix for IDT codecs to keep the power up while the beep is
enabled can be better integrated into the beep helper code.
This patch cleans up the code with refactoring.
The tracing capabilities for the speaker protection fw enabled via
commit c55b3e46cb99 ("ASoC: wm_adsp: Add trace caps to speaker
protection FW") are not be available on all platforms, such as the
Valve's Steam Deck which is based on the Halo Core DSP.
As a consequence, whenever the firmware is loaded, a rather misleading
'Failed to parse legacy: -19' error message is written to the kernel
ring buffer:
As rsnd_mod_power_on() can return negative numbers,
it should be better to check the return value and
deal with the exception.
Fixes: e7d850dd10f4 ("ASoC: rsnd: use mod base common method on SSI-parent") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20220902013030.3691266-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Send DP_SET_POWER_D3 command to the downstream before stopping DP, so the
suspend process will not be interrupted by the HPD interrupt. Also modify
the order in .atomic_enable callback to make the callbacks symmetric.
Fixes: 46ca7da7f1e8 ("drm/bridge: it6505: Send DPCD SET_POWER to downstream") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220830045756.1655954-1-treapking@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The two bridges (stdp2690, stdp4028) do not probe at the same time, so
the driver does not call ge_b850v3_resgiter() when probing, causing the
driver to try to remove the object that has not been initialized.
Fix this by checking whether both the bridges are probed.
Add missing pci_disable_device() if amdgpu_device_resume() fails.
Fixes: 8e4d5d43cc6c ("drm/amdgpu: Handling of amdgpu_device_resume return value for graceful teardown") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drm_mipi_dbi needs lots of DRM_KMS_HELPER support, so select
that Kconfig symbol like it is done is most other uses, and
the way that it was before MIPS_DBI was moved from tinydrm
to its core location.
Fixes these build errors:
ld: drivers/gpu/drm/drm_mipi_dbi.o: in function `mipi_dbi_buf_copy':
drivers/gpu/drm/drm_mipi_dbi.c:205: undefined reference to `drm_gem_fb_get_obj'
ld: drivers/gpu/drm/drm_mipi_dbi.c:211: undefined reference to `drm_gem_fb_begin_cpu_access'
ld: drivers/gpu/drm/drm_mipi_dbi.c:215: undefined reference to `drm_gem_fb_vmap'
ld: drivers/gpu/drm/drm_mipi_dbi.c:222: undefined reference to `drm_fb_swab'
ld: drivers/gpu/drm/drm_mipi_dbi.c:224: undefined reference to `drm_fb_memcpy'
ld: drivers/gpu/drm/drm_mipi_dbi.c:227: undefined reference to `drm_fb_xrgb8888_to_rgb565'
ld: drivers/gpu/drm/drm_mipi_dbi.c:235: undefined reference to `drm_gem_fb_vunmap'
ld: drivers/gpu/drm/drm_mipi_dbi.c:237: undefined reference to `drm_gem_fb_end_cpu_access'
ld: drivers/gpu/drm/drm_mipi_dbi.o: in function `mipi_dbi_dev_init_with_formats':
ld: drivers/gpu/drm/drm_mipi_dbi.o:/X64/../drivers/gpu/drm/drm_mipi_dbi.c:469: undefined reference to `drm_gem_fb_create_with_dirty'
Fixes: 174102f4de23 ("drm/tinydrm: Move mipi-dbi") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Dillon Min <dillon.minfei@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: dri-devel@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220823004243.11596-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Use 'select' instead of 'depends on' for DRM helpers for the
Ilitek ILI9341 panel driver.
This is what is done in the vast majority of other cases and
this makes it possible to fix a build error with drm_mipi_dbi.
Fixes: 5a04227326b0 ("drm/panel: Add ilitek ili9341 panel driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Dillon Min <dillon.minfei@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: dri-devel@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220823004227.10820-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2cc6c717799f ("msi-laptop: Port to new backlight interface
selection API") replaced this check:
if (!quirks->old_ec_model || acpi_video_backlight_support())
pr_info("Brightness ignored, ...");
else
do_register();
With:
if (quirks->old_ec_model ||
acpi_video_get_backlight_type() == acpi_backlight_vendor)
do_register();
But since the do_register() part was part of the else branch, the entire
condition should be inverted. So not only the 2 statements on either
side of the || should be inverted, but the || itself should be replaced
with a &&.
In practice this has likely not been an issue because the new-ec models
(old_ec_model==false) likely all support ACPI video backlight control,
making acpi_video_get_backlight_type() return acpi_backlight_video
turning the second part of the || also false when old_ec_model == false.
Because the PWR_CTRL field is modeled as the power state of the DAC
widget, and at the same time it is used to implement mute/unmute, we
need some additional book-keeping to have the right end result no matter
the sequence of calls. Without this fix, one permanently mutes an
ongoing stream by toggling the associated speaker pin control.
(This mirrors commit 1e5907bcb3a3 ("ASoC: tas2770: Fix handling of
mute/unmute") which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Link: https://lore.kernel.org/r/20220825140241.53963-4-povik+lin@cutebit.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver is setting the PWR_CTRL field in both the set_bias_level
callback and on DAPM events of the DAC widget (and also in the
mute_stream method). Drop the set_bias_level callback altogether as the
power setting it does is in conflict with the other code paths.
(This mirrors commit c8a6ae3fe1c8 ("ASoC: tas2770: Drop conflicting
set_bias_level power setting") which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Link: https://lore.kernel.org/r/20220825140241.53963-3-povik+lin@cutebit.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The part is a mono speaker amp, but it can do downmix and switch between
left and right channel, so the right channel range is 1 to 2.
(This mirrors commit bf54d97a835d ("ASoC: tas2770: Allow mono streams")
which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Link: https://lore.kernel.org/r/20220825140241.53963-2-povik+lin@cutebit.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b7898396f4bbe16 ("ASoC: soc-pcm: Fix and cleanup DPCM locking")
added __soc_pcm_close() for non-lock version of soc_pcm_close().
But soc_pcm_close() is not using it. It is no problem, but confusable.
static int __soc_pcm_close(...)
{
=> return soc_pcm_clean(rtd, substream, 0);
}
If chromeos_laptop_prepare_i2c_peripherals() fails after allocating memory
for 'cros_laptop->i2c_peripherals', this memory is freed at 'err_out' label
and nonzero value is returned. Then chromeos_laptop_destroy() is called,
resulting in double-free error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Drivers' .remove and .shutdown callbacks are executed on different code
paths. The former is called when a device is removed from the bus, while
the latter is called at system shutdown time to quiesce the device.
This means that some overlap exists between the two, because both have to
take care of properly shutting down the hardware. But currently the logic
used in these two callbacks isn't consistent in msm drivers, which could
lead to kernel panic.
For example, on .remove the component is deleted and its .unbind callback
leads to the hardware being shutdown but only if the DRM device has been
marked as registered.
That check doesn't exist in the .shutdown logic and this can lead to the
driver calling drm_atomic_helper_shutdown() for a DRM device that hasn't
been properly initialized.
A situation like this can happen if drivers for expected sub-devices fail
to probe, since the .bind callback will never be executed. If that is the
case, drm_atomic_helper_shutdown() will attempt to take mutexes that are
only initialized if drm_mode_config_init() is called during a device bind.
This bug was attempted to be fixed in commit 623f279c7781 ("drm/msm: fix
shutdown hook in case GPU components failed to bind"), but unfortunately
it still happens in some cases as the one mentioned above, i.e:
The reference 'child' in the iteration of for_each_available_child_of_node()
is only escaped out into a local variable which is only used to check
its value. So we still need to the of_node_put() when breaking of the
for_each_available_child_of_node() which will automatically increase
and decrease the refcount.
Fixes: ca454bd42dc2 ("drm/pl111: Support the Versatile Express") Signed-off-by: Liang He <windhl@126.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20220711131550.361350-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
