To prevent any recovery work running after the queue cleanup cancel it.
Any recovery running post-cleanup dereferenced mq->card as NULL
and was not meaningful to begin with.
Cc: stable@vger.kernel.org Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/c865c0c9789d428494b67b820a78923e@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before switching back to the right partition in mmc_blk_reset there used
to be a check if hw_reset was even supported. This return value
was removed, so there is no reason to check. Furthermore ensure
part_curr is not falsely set to a valid value on reset or
partition switch error.
As part of this change the code paths of mmc_blk_reset calls were checked
to ensure no commands are issued after a failed mmc_blk_reset directly
without going through the block layer.
Fixes: fefdd3c91e0a ("mmc: core: Drop superfluous validations in mmc_hw|sw_reset()") Cc: stable@vger.kernel.org Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/e91be6199d04414a91e20611c81bfe1d@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REGMAP_MMIO is not user-configurable, so we can only satisfy this
dependency by enabling some other Kconfig symbol that properly 'select's
it. Use select like everybody else.
Noticed when trying to enable this driver for compile testing.
cti_enable_hw() and cti_disable_hw() are called from an atomic context
so shouldn't use runtime PM because it can result in a sleep when
communicating with firmware.
Since commit 3c6656337852 ("Revert "firmware: arm_scmi: Add clock
management to the SCMI power domain""), this causes a hang on Juno when
running the Perf Coresight tests or running this command:
perf record -e cs_etm//u -- ls
This was also missed until the revert commit because pm_runtime_put()
was called with the wrong device until commit 692c9a499b28 ("coresight:
cti: Correct the parameter for pm_runtime_put")
With lock and scheduler debugging enabled the following is output:
coresight cti_sys0: cti_enable_hw -- dev:cti_sys0 parent: 20020000.cti
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1151
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 330, name: perf-exec
preempt_count: 2, expected: 0
RCU nest depth: 0, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<0000000000000000>] 0x0
hardirqs last disabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last enabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 3 PID: 330 Comm: perf-exec Not tainted 6.0.0-00053-g042116d99298 #7
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Sep 13 2022
Call trace:
dump_backtrace+0x134/0x140
show_stack+0x20/0x58
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
__might_resched+0x180/0x228
__might_sleep+0x50/0x88
__pm_runtime_resume+0xac/0xb0
cti_enable+0x44/0x120
coresight_control_assoc_ectdev+0xc0/0x150
coresight_enable_path+0xb4/0x288
etm_event_start+0x138/0x170
etm_event_add+0x48/0x70
event_sched_in.isra.122+0xb4/0x280
merge_sched_in+0x1fc/0x3d0
visit_groups_merge.constprop.137+0x16c/0x4b0
ctx_sched_in+0x114/0x1f0
perf_event_sched_in+0x60/0x90
ctx_resched+0x68/0xb0
perf_event_exec+0x138/0x508
begin_new_exec+0x52c/0xd40
load_elf_binary+0x6b8/0x17d0
bprm_execve+0x360/0x7f8
do_execveat_common.isra.47+0x218/0x238
__arm64_sys_execve+0x48/0x60
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.4+0xfc/0x120
do_el0_svc+0x34/0xc0
el0_svc+0x40/0x98
el0t_64_sync_handler+0x98/0xc0
el0t_64_sync+0x170/0x174
Fix the issue by removing the runtime PM calls completely. They are not
needed here because it must have already been done when building the
path for a trace.
Fixes: 835d722ba10a ("coresight: cti: Initial CoreSight CTI Driver") Cc: stable <stable@kernel.org> Reported-by: Aishwarya TCV <Aishwarya.TCV@arm.com> Reported-by: Cristian Marussi <Cristian.Marussi@arm.com> Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: James Clark <james.clark@arm.com> Reviewed-by: Mike Leach <mike.leach@linaro.org> Tested-by: Mike Leach <mike.leach@linaro.org>
[ Fix build warnings ] Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20221025131032.1149459-1-suzuki.poulose@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reworking the archrandom handling, commit d349ab99eec7 ("random:
handle archrandom with multiple longs") switched to the non-early
archrandom helpers in random_init(), which broke initialization of the
entropy pool from the arm64 random generator.
Indeed at that point the arm64 CPU features, which verify that all CPUs
have compatible capabilities, are not finalized so arch_get_random_seed_longs()
is unsuccessful. Instead random_init() should use the _early functions,
which check only the boot CPU on arm64. On other architectures the
_early functions directly call the normal ones.
Fixes: d349ab99eec7 ("random: handle archrandom with multiple longs") Cc: stable@vger.kernel.org Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device-managed resources allocated post component bind must be tied to
the lifetime of the aggregate DRM device or they will not necessarily be
released when binding of the aggregate device is deferred.
This can lead resource leaks or failure to bind the aggregate device
when binding is later retried and a second attempt to allocate the
resources is made.
For the DP bridges, previously allocated bridges will leak on probe
deferral.
Fix this by amending the DP parser interface and tying the lifetime of
the bridge device to the DRM device rather than DP platform device.
Device-managed resources allocated post component bind must be tied to
the lifetime of the aggregate DRM device or they will not necessarily be
released when binding of the aggregate device is deferred.
This is specifically true for the DP IRQ, which will otherwise remain
requested so that the next bind attempt fails when requesting the IRQ a
second time.
Since commit c3bf8e21b38a ("drm/msm/dp: Add eDP support via aux_bus")
this can happen when the aux-bus panel driver has not yet been loaded so
that probe is deferred.
Fix this by tying the device-managed lifetime of the DP IRQ to the DRM
device so that it is released when bind fails.
Device-managed resources allocated post component bind must be tied to
the lifetime of the aggregate DRM device or they will not necessarily be
released when binding of the aggregate device is deferred.
This can lead resource leaks or failure to bind the aggregate device
when binding is later retried and a second attempt to allocate the
resources is made.
For the DP aux-bus, an attempt to populate the bus a second time will
simply fail ("DP AUX EP device already populated").
Fix this by tying the lifetime of the EP device to the DRM device rather
than DP controller platform device.
Fixes: c3bf8e21b38a ("drm/msm/dp: Add eDP support via aux_bus") Cc: stable@vger.kernel.org # 5.19 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502672/ Link: https://lore.kernel.org/r/20220913085320.8577-7-johan+linaro@kernel.org Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing sanity check on the bridge counter to avoid corrupting
data beyond the fixed-sized bridge array in case there are ever more
than eight bridges.
Device-managed resources allocated post component bind must be tied to
the lifetime of the aggregate DRM device or they will not necessarily be
released when binding of the aggregate device is deferred.
This is specifically true for the HDMI IRQ, which will otherwise remain
requested so that the next bind attempt fails when requesting the IRQ a
second time.
Fix this by tying the device-managed lifetime of the HDMI IRQ to the DRM
device so that it is released when bind fails.
Add the missing sanity check on the bridge counter to avoid corrupting
data beyond the fixed-sized bridge array in case there are ever more
than eight bridges.
Add the missing sanity check on the bridge counter to avoid corrupting
data beyond the fixed-sized bridge array in case there are ever more
than eight bridges.
The bridge counter was never reset when tearing down the DRM device so
that stale pointers to deallocated structures would be accessed on the
next tear down (e.g. after a second late bind deferral).
Given enough bridges and a few probe deferrals this could currently also
lead to data beyond the bridge array being corrupted.
This file was split in commit 5d945cbcd4b16a29d6470a80dfb19738f9a4319f
("drm/amd/display: Create a file dedicated to planes") and the logic in
dm_plane_format_mod_supported() function got changed by a switch logic.
That change broke drm_plane modifiers setting on series 5000 APUs
(tested on OXP mini AMD 5800U and HP Dev One 5850U PRO)
leading to Gamescope not working as reported on GitHub[1]
To reproduce the issue, enter a TTY and run:
$ gamescope -- vkcube
With said commit applied it will abort. This one restores the old logic,
fixing the issue that affects Gamescope.
[WHY]
0, original pstate X
1, ctx_A_create -> ctx_A->stable_pstate = X
2, ctx_A_set_pstate (Y) -> current pstate is Y (PEAK or STANDARD)
3, ctx_B_create -> ctx_B->stable_pstate = Y
4, ctx_A_destroy -> restore pstate to X
5, ctx_B_destroy -> restore pstate to Y
Above sequence will cause final pstate is wrong (Y), should be original X.
[HOW]
When ctx_B create,
if ctx_A touched pstate setting
(not auto, stable_pstate_ctx != NULL),
set ctx_B->stable_pstate the same value as ctx_A saved,
if stable_pstate_ctx == NULL,
fetch current pstate to fill
ctx_B->stable_pstate.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the S2idle suspend/resume phase the gfxoff is keeping functional so
some IP blocks will be likely to reinitialize at gfxoff entry and that
will result in failing to program GC registers.Therefore, let disallow
gfxoff until AMDGPU IPs reinitialized completely.
Signed-off-by: Prike Liang <Prike.Liang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 5.15.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MMHUB 2.1.x versions don't have ATCL2. Remove accesses to ATCL2 registers.
Since they are non-existing registers, read access will cause a
'Completer Abort' and gets reported when AER is enabled with the below patch.
Tagging with the patch so that this is backported along with it.
v2: squash in uninitialized warning fix (Nathan Chancellor)
A user reported a bug on CAPE VERDE system where uvd_v3_1
IP component failed to initialize as there is an issue with
BO move code from one memory to other.
In function amdgpu_mem_visible() called by amdgpu_bo_move(),
when there are no blocks to compare or if we have a single
block then break the loop.
Fixes: 312b4dc11d4f ("drm/amdgpu: Fix VRAM BO swap issue") Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DRM buddy manager allocates the contiguous memory requests in
a single block or multiple blocks. So for the ttm move operation
(incase of low vram memory) we should consider all the blocks to
compute the total memory size which compared with the struct
ttm_resource num_pages in order to verify that the blocks are
contiguous for the eviction process.
v2: Added a Fixes tag
v3: Rewrite the code to save a bit of calculations and
variables (Christian)
Fixes: c9cad937c0c5 ("drm/amdgpu: add drm buddy support to amdgpu") Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the sysfs values reported for supported_speeds was not valid (20Gb/s
reported instead of 64Gb/s). Instead of driver internal speed mask
definition, use speed mask defined in transport_fc for reporting
host->supported_speeds.
Back in 2014, the LQI was saved in the skb control buffer (skb->cb, or
mac_cb(skb)) without any actual reset of this area prior to its use.
As part of a useful rework of the use of this region, 32edc40ae65c
("ieee802154: change _cb handling slightly") introduced mac_cb_init() to
basically memset the cb field to 0. In particular, this new function got
called at the beginning of mac802154_parse_frame_start(), right before
the location where the buffer got actually filled.
What went through unnoticed however, is the fact that the very first
helper called by device drivers in the receive path already used this
area to save the LQI value for later extraction. Resetting the cb field
"so late" led to systematically zeroing the LQI.
If we consider the reset of the cb field needed, we can make it as soon
as we get an skb from a device driver, right before storing the LQI,
as is the very first time we need to write something there.
unshare_sighand should only access oldsighand->action
while holding oldsighand->siglock, to make sure that
newsighand->action is in a consistent state.
If "interp_elf_ex" fails to allocate memory in load_elf_binary(),
the program will take the "out_free_ph" error handing path,
resulting in "interpreter" file resource is not released.
Fix it by adding an error handing path "out_free_file", which will
release the file resource when "interp_elf_ex" failed to allocate
memory.
Fixes: 0693ffebcfe5 ("fs/binfmt_elf.c: allocate less for static executable") Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221024154421.982230-1-lizetao1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 46573fd6369f ("cpufreq: intel_pstate: hybrid: Rework HWP
calibration") attempted to use the information from CPPC (the nominal
performance in particular) to obtain the scaling factor allowing the
frequency to be computed if the HWP performance level of the given CPU
is known or vice versa.
However, it turns out that on some platforms this doesn't work, because
the CPPC information on them does not align with the contents of the
MSR_HWP_CAPABILITIES registers.
This basically means that the only way to make intel_pstate work on all
of the hybrid platforms to date is to use the observation that on all
of them the scaling factor between the HWP performance levels and
frequency for P-cores is 78741 (approximately 100000/1.27). For
E-cores it is 100000, which is the same as for all of the non-hybrid
"core" platforms and does not require any changes.
Accordingly, make intel_pstate use 78741 as the scaling factor between
HWP performance levels and frequency for P-cores on all hybrid platforms
and drop the dependency of the HWP calibration code on CPPC.
Some of the MSR accesses in intel_pstate are carried out on the CPU
that is running the code, but the values coming from them are used
for the performance scaling of the other CPUs.
This is problematic, for example, on hybrid platforms where
MSR_TURBO_RATIO_LIMIT for P-cores and E-cores is different, so the
values read from it on a P-core are generally not applicable to E-cores
and the other way around.
For this reason, make the driver access all MSRs on the target CPU on
platforms using the "core" pstate_funcs callbacks which is the case for
all of the hybrid platforms released to date. For this purpose, pass
a CPU argument to the ->get_max(), ->get_max_physical(), ->get_min()
and ->get_turbo() pstate_funcs callbacks and from there pass it to
rdmsrl_on_cpu() or rdmsrl_safe_on_cpu() to access the MSR on the target
CPU.
When the text console is scrolling text upwards it calls the fillrect()
function to empty the new line. The current implementation doesn't seem
to work correctly on HCRX cards in 32-bit mode and leave garbage in that
line instead. Fix it by falling back to standard cfb_fillrect() in that
case.
The devm_iio_kfifo_buffer_setup_ext() was changed by
commit 15097c7a1adc ("iio: buffer: wrap all buffer attributes into iio_dev_attr")
to silently expect that all attributes given in buffer_attrs array are
device-attributes. This expectation was not forced by the API - and some
drivers did register attributes created by IIO_CONST_ATTR().
The added attribute "wrapping" does not copy the pointer to stored
string constant and when the sysfs file is read the kernel will access
to invalid location.
Change the IIO_CONST_ATTRs from the driver to IIO_DEVICE_ATTR in order
to prevent the invalid memory access.
The iio_triggered_buffer_setup_ext() was changed by
commit 15097c7a1adc ("iio: buffer: wrap all buffer attributes into iio_dev_attr")
to silently expect that all attributes given in buffer_attrs array are
device-attributes. This expectation was not forced by the API - and some
drivers did register attributes created by IIO_CONST_ATTR().
The added attribute "wrapping" does not copy the pointer to stored
string constant and when the sysfs file is read the kernel will access
to invalid location.
Change the IIO_CONST_ATTRs from the driver to IIO_DEVICE_ATTR in order
to prevent the invalid memory access.
Currently, every time the device wakes up from sleep, the
iio_chan array is reallocated, leaking the previous one
until the device is removed (basically never).
Move the allocation to the probe function to avoid this.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com> Fixes: f110f3188e563 ("iio: temperature: Add support for LTC2983") Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20221014123724.1401011-2-demonsingur@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tsl2583 probe() uses devm_iio_device_register() and calling
iio_device_unregister() causes the unregister to occur twice. s
Switch to iio_device_register() instead of devm_iio_device_register()
in probe to avoid the device managed cleanup.
The iio_utils uses a digit calculation in order to know length of the
file name containing a buffer number. The digit calculation does not
work for number 0.
This leads to allocation of one character too small buffer for the
file-name when file name contains value '0'. (Eg. buffer0).
Fix digit calculation by returning one digit to be present for number
'0'.
Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.
If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.
So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.
Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.
This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)
Cc: stable@vger.kernel.org Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For optimal power consumption of USB4 routers the XHCI PCIe endpoint
used for tunneling must be in D3. Historically this is accomplished
by a long list of PCIe IDs that correspond to these endpoints because
the xhci_hcd driver will not default to allowing runtime PM for all
devices.
As both AMD and Intel have released new products with new XHCI controllers
this list continues to grow. In reviewing the XHCI specification v1.2 on
page 607 there is already a requirement that the PCI power management
states D3hot and D3cold must be supported.
In the quirk list, use this to indicate that runtime PM should be allowed
on XHCI controllers. The following controllers are known to be xHC 1.2 and
dropped explicitly:
* AMD Yellow Carp
* Intel Alder Lake
* Intel Meteor Lake
* Intel Raptor Lake
[keep PCI ID for Alder Lake PCH for recently added quirk -Mathias]
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ecf1 ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
The readahead code will try to extend readahead to the entire size of the
Squashfs data block.
But, it didn't take into account that the last block at the end of the
file may not be a whole block. In this case, the code would extend
readahead to beyond the end of the file, leaving trailing pages.
Fix this by only requesting the expected number of pages.
Patch series "squashfs: fix some regressions introduced in the readahead
code".
This patchset fixes 3 regressions introduced by the recent readahead code
changes. The first regression is causing "snaps" to randomly fail after a
couple of hours or days, which how the regression came to light.
This patch (of 3):
If a file isn't a whole multiple of the page size, the last page will have
trailing bytes unfilled.
There was a mistake in the readahead code which did this. In particular
it incorrectly assumed that the last page in the readahead page array
(page[nr_pages - 1]) will always contain the last page in the block, which
if we're at file end, will be the page that needs to be zero filled.
But the readahead code may not return the last page in the block, which
means it is unmapped and will be skipped by the decompressors (a temporary
buffer used).
In this case the zero filling code will zero out the wrong page, leading
to data corruption.
Fix this by by extending the "page actor" to return the last page if
present, or NULL if a temporary buffer was used.
Originally the absence of the marvell,nand-keep-config property caused
the setup_data_interface function to be provided. However when
setup_data_interface was moved into nand_controller_ops the logic was
unintentionally inverted. Update the logic so that only if the
marvell,nand-keep-config property is present the bootloader NAND config
kept.
Cc: stable@vger.kernel.org Fixes: 7a08dbaedd36 ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops") Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is some code in the parser that tries to read 0x8000
bytes into a block to "read in the middle" of the block. Well
that only works if the block is also 0x10000 bytes all the time,
else we get these parse errors as we reach the end of the flash:
spi-nor spi0.0: mx25l1606e (2048 Kbytes)
mtd_read error while parsing (offset: 0x200000): -22
mtd_read error while parsing (offset: 0x201000): -22
(...)
The Intel SPI-NOR controller does not support the 4-byte address opcode
so ->set_4byte_addr_mode() ends up returning -ENOTSUPP and the SPI flash
chip probe fail like this:
[ 12.291082] spi-nor: probe of spi0.0 failed with error -524
Whereas previously before commit 08412e72afba ("mtd: spi-nor: core:
Return error code from set_4byte_addr_mode()") it worked just fine.
Fix this by ignoring -ENOTSUPP in spi_nor_init().
Fixes: 08412e72afba ("mtd: spi-nor: core: Return error code from set_4byte_addr_mode()") Cc: stable@vger.kernel.org Reported-by: Hongyu Ning <hongyu.ning@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Michael Walle <michael@walle.cc> Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220923093441.3178-1-mika.westerberg@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
This appears to fix the error:
"xhci_hcd <address>; ERROR Transfer event TRB DMA ptr not part of
current TD ep_index 2 comp_code 13" that appear spuriously (or pretty
often) when using a r8152 USB3 ethernet adapter with integrated hub.
ASM1042 reports as a 0.96 controller, but appears to behave more like 1.0
Inspired by this email thread: https://markmail.org/thread/7vzqbe7t6du6qsw3
When port is connected and then disconnected, the state stays as
configured. Which is incorrect as the port is no longer configured,
but in a not attached state.
If the extcon device exists, get the mode from the extcon device. If
the controller is DRD and the driver is unable to determine the mode,
only then default the dr_mode to USB_DR_MODE_PERIPHERAL.
The ACPI driver needs to resume the interface by calling
ucsi_resume(). Otherwise we may fail to detect connections
and disconnections that happen while the system is
suspended.
Checking the connection status of every port on resume. This
fixes an issue where the partner device is not unregistered
properly after resume if it was unplugged while the system
was suspended.
The function ucsi_check_connection() is also modified so
that it can be used also for registering the connection on
top of unregistering it.
The gadget driver may wait on the request completion when it sets the
USB_GADGET_DELAYED_STATUS. Make sure that the End Transfer command can
go through if the dwc->delayed_status is set so that the request can
complete. When the delayed_status is set, the Setup packet is already
processed, and the next phase should be either Data or Status. It's
unlikely that the host would cancel the control transfer and send a new
Setup packet during End Transfer command. But if that's the case, we can
try again when ep0state returns to EP0_SETUP_PHASE.
If any function drivers request for a delayed status phase, this leads to a
SETUP transfer timeout error, since the function may take longer to process
the DATA stage. This eventually results in end transfer timeouts, as there
is a pending SETUP transaction.
In addition, allow the DWC3_EP_DELAY_STOP to be set for if there is a
delayed status requested. Ocasionally, a host may abort the current SETUP
transaction, by issuing a subsequent SETUP token. In those situations, it
would result in an endxfer timeout as well.
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable@vger.kernel.org Reported-by: Jeff Vanhoof <jdv1029@gmail.com> Reported-by: Dan Vacura <w36195@motorola.com> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com> Tested-by: Jeff Vanhoof <jdv1029@gmail.com> Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fc274c1e9973 ("USB: gadget: Add a new bus for gadgets"),
the gadget devices are proper driver core devices, which caused each
device to request pinmux settings:
aspeed_vhub 1e6a0000.usb-vhub: Initialized virtual hub in USB2 mode
aspeed-g5-pinctrl 1e6e2080.pinctrl: pin A7 already requested by 1e6a0000.usb-vhub; cannot claim for gadget.0
aspeed-g5-pinctrl 1e6e2080.pinctrl: pin-232 (gadget.0) status -22
aspeed-g5-pinctrl 1e6e2080.pinctrl: could not request pin 232 (A7) from group USB2AD on device aspeed-g5-pinctrl
g_mass_storage gadget.0: Error applying setting, reverse things back
The vhub driver has already claimed the pins, so prevent the gadgets
from requesting them too by setting the magic of_node_reused flag. This
causes the driver core to skip the mux request.
Reported-by: Zev Weiss <zev@bewilderbeest.net> Reported-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Fixes: fc274c1e9973 ("USB: gadget: Add a new bus for gadgets") Cc: stable@vger.kernel.org Signed-off-by: Joel Stanley <joel@jms.id.au> Tested-by: Zev Weiss <zev@bewilderbeest.net> Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Link: https://lore.kernel.org/r/20221017053006.358520-1-joel@jms.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uvc_video_encode_isoc_sg, the uvc_request's sg list is
incorrectly being populated leading to corrupt video being
received by the remote end. When building the sg list the
usage of buf->sg's 'dma_length' field is not correct and
instead its 'length' field should be used.
If there is a transmission error the buffer will be returned too early,
causing a memory fault as subsequent requests for that buffer are still
queued up to be sent. Refactor the error handling to wait for the final
request to come in before reporting back the buffer to userspace for all
transfer types (bulk/isoc/isoc_sg). This ensures userspace knows if the
frame was successfully sent.
With the re-use of the previous completion status in 0d1c407b1a749
("usb: dwc3: gadget: Return proper request status") it could be possible
that the next frame would also get dropped if the current frame has a
missed isoc error. Ensure that an interrupt is requested for the start
of a new frame.
Fixes: fc78941d8169 ("usb: gadget: uvc: decrease the interrupt load to a quarter") Cc: <stable@vger.kernel.org> Signed-off-by: Dan Vacura <w36195@motorola.com> Link: https://lore.kernel.org/r/20221018215044.765044-2-w36195@motorola.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The overhead of preparing sg data is high for transfers with limited
payload. When transferring isoc over high-speed usb the maximum payload
is rather small which is a good argument no to use sg. This patch is
changing the uvc_video_encode_isoc_sg encode function only to be used
for super speed gadgets.
NVIDIA Jetson devices in Force Recovery mode (RCM) do not support
suspending, ie. flashing fails if the device has been suspended. The
devices are still visible in lsusb and seem to work otherwise, making
the issue hard to debug. This has been discovered in various forum
posts, eg. [1].
The patch has been tested on NVIDIA Jetson AGX Xavier, but I'm adding
all the Jetson models listed in [2] on the assumption that they all
behave similarly.
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, signed chars need to be marked
explicitly as such. This fixes warnings like:
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, signed chars need to be marked
explicitly as such. This fixes warnings like:
With the recent addition of hashed controls lookup it's not enough to just
update the control name field, the hash entries for the modified control
have to be updated too.
snd_ctl_rename() takes care of that, so use it instead of directly
modifying the control name.
With the recent addition of hashed controls lookup it's not enough to just
update the control name field, the hash entries for the modified control
have to be updated too.
snd_ctl_rename() takes care of that, so use it instead of directly
modifying the control name.
With the recent addition of hashed controls lookup it's not enough to just
update the control name field, the hash entries for the modified control
have to be updated too.
snd_ctl_rename() takes care of that, so use it instead of directly
modifying the control name.
While we are at it, check also that the new control name doesn't
accidentally overwrite the available buffer space.
With the recent addition of hashed controls lookup it's not enough to just
update the control name field, the hash entries for the modified control
have to be updated too.
snd_ctl_rename() takes care of that, so use it instead of directly
modifying the control name.
With the recent addition of hashed controls lookup it's not enough to just
update the control name field, the hash entries for the modified control
have to be updated too.
snd_ctl_rename() takes care of that, so use it instead of directly
modifying the control name.
Add a snd_ctl_rename() function that takes care of updating the control
hash entries for callers that already have the relevant struct snd_kcontrol
at hand and hold the control write lock (or simply haven't registered the
card yet).
M-Audio Fast Track C400 and C600 devices (0763:2030 and 0763:2031,
respectively) seem requiring the explicit setup for the implicit
feedback mode. This patch adds the quirk entries for those.
Instead just use del_timer_sync() which will wait for the timer to finish
before continuing. No need to check if the timer is active or not when
doing so.
This doesn't fix the race of a possible re-arming of the timer, but at
least it won't use the data that has just been freed.
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes: 76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family") Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org
[mkl: adjust commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org
[mkl: adjust commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Tested-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not allowed to call kfree_skb() from hardware interrupt context
or with interrupts being disabled. The skb is unlinked from the queue,
so it can be freed after spin_unlock_irqrestore().
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/all/20221027091237.2290111-1-yangyingliang@huawei.com Cc: stable@vger.kernel.org
[mkl: adjust subject] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since linux/debugfs.h already has the stubs for the used debugfs
functions when debugfs is not enabled, remove the #ifdef CONFIG_DEBUG_FS
checks.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Link: https://lore.kernel.org/r/20220922175608.630046-1-Shyam-sundar.S-k@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: Jaak Ristioja <jaak@ristioja.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seth Jenkins [Thu, 27 Oct 2022 15:36:52 +0000 (11:36 -0400)]
mm: /proc/pid/smaps_rollup: fix no vma's null-deref
Commit 258f669e7e88 ("mm: /proc/pid/smaps_rollup: convert to single value
seq_file") introduced a null-deref if there are no vma's in the task in
show_smaps_rollup.
Fixes: 258f669e7e88 ("mm: /proc/pid/smaps_rollup: convert to single value seq_file") Signed-off-by: Seth Jenkins <sethjenkins@google.com> Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com> Tested-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is very different from the upstream commit! It fixes the same
issue by adding more quirks, rather then the general fix from the 6.1
kernel, because the general fix from the 6.1 kernel is part of a larger
refactoring of the backlight code which is not suitable for the stable
series.
As described in "ACPI: video: Drop NL5x?U, PF4NU1F and PF5?U??
acpi_backlight=native quirks" (10212754a0d2) the upstream commit "ACPI:
video: Make backlight class device registration a separate step (v2)"
(3dbc80a3e4c5) makes these quirks unnecessary. However as mentioned in this
bugtracker ticket https://bugzilla.kernel.org/show_bug.cgi?id=215683#c17
the upstream fix is part of a larger patchset that is overall too complex
for stable.
The TongFang GKxNRxx, GMxNGxx, GMxZGxx, and GMxRGxx / TUXEDO
Stellaris/Polaris Gen 1-4, have the same problem as the Clevo NL5xRU and
NL5xNU / TUXEDO Aura 15 Gen1 and Gen2:
They have a working native and video interface for screen backlight.
However the default detection mechanism first registers the video interface
before unregistering it again and switching to the native interface during
boot. This results in a dangling SBIOS request for backlight change for
some reason, causing the backlight to switch to ~2% once per boot on the
first power cord connect or disconnect event. Setting the native interface
explicitly circumvents this buggy behaviour by avoiding the unregistering
process.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For scan loop must ensure that at least EXT4_FC_TAG_BASE_LEN space. If remain
space less than EXT4_FC_TAG_BASE_LEN which will lead to out of bound read
when mounting corrupt file system image.
ADD_RANGE/HEAD/TAIL is needed to add extra check when do journal scan, as this
three tags will read data during scan, tag length couldn't less than data length
which will read.
This isn't a reliable mechanism to tell if we have task_work pending, we
really should be looking at whether we have any items queued. This is
problematic if forward progress is gated on running said task_work. One
such example is reading from a pipe, where the write side has been closed
right before the read is started. The fput() of the file queues TWA_RESUME
task_work, and we need that task_work to be run before ->release() is
called for the pipe. If ->release() isn't called, then the read will sit
forever waiting on data that will never arise.
Fix this by io_run_task_work() so it checks if we have task_work pending
rather than rely on TIF_NOTIFY_SIGNAL for that. The latter obviously
doesn't work for task_work that is queued without TWA_SIGNAL.
In case of PCIe interoperability problem shows up, the firmware
payload may be corrupted in download stage. Turn off L0s to keep
fw download process accurately.
[ 1093.528363] mt7921e 0000:3b:00.0: Message 00000007 (seq 7) timeout
[ 1093.528414] mt7921e 0000:3b:00.0: Failed to start patch
[ 1096.600156] mt7921e 0000:3b:00.0: Message 00000010 (seq 8) timeout
[ 1096.600207] mt7921e 0000:3b:00.0: Failed to release patch semaphore
[ 1097.699031] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1098.758427] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1099.834408] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1100.915264] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1101.990625] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1103.077587] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1104.173258] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1105.248466] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1106.336969] mt7921e 0000:3b:00.0: Timeout for driver own
[ 1106.397542] mt7921e 0000:3b:00.0: hardware init failed
Cc: stable@vger.kernel.org Fixes: bf3747ae2e25 ("mt76: mt7921: enable aspm by default") Signed-off-by: Deren Wu <deren.wu@mediatek.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
A splat from kmem_cache_destroy() was seen with a kernel prior to
commit ee2653bbe89d ("iommu/vt-d: Remove domain and devinfo mempool")
when there was a failure in init_dmars(), because the iommu_domain
cache still had objects. While the mempool code is now gone, there
still is a leak of the si_domain memory if init_dmars() fails. So
clean up si_domain in the init_dmars() error path.
Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Will Deacon <will@kernel.org> Cc: Robin Murphy <robin.murphy@arm.com> Fixes: 86080ccc223a ("iommu/vt-d: Allocate si_domain in init_dmars()") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20221010144842.308890-1-jsnitsel@redhat.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch_rmrr_sanity_check() warns if the RMRR is not covered by an ACPI
Reserved region, but it seems like it should accept an NVS region as
well. The ACPI spec
https://uefi.org/specs/ACPI/6.5/15_System_Address_Map_Interfaces.html
uses similar wording for "Reserved" and "NVS" region types; for NVS
regions it says "This range of addresses is in use or reserved by the
system and must not be used by the operating system."
There is an old comment on this mailing list that also suggests NVS
regions should pass the arch_rmrr_sanity_check() test:
The warnings come from arch_rmrr_sanity_check() since it checks whether
the region is E820_TYPE_RESERVED. However, if the purpose of the check
is to detect RMRR has regions that may be used by OS as free memory,
isn't E820_TYPE_NVS safe, too?
This patch overlaps with another proposed patch that would add the region
type to the log since sometimes the bug reporter sees this log on the
console but doesn't know to include the kernel log:
Here's an example of the "Firmware Bug" apparent false positive (wrapped
for line length):
DMAR: [Firmware Bug]: No firmware reserved region can cover this RMRR
[0x000000006f760000-0x000000006f762fff], contact BIOS vendor for
fixes
DMAR: [Firmware Bug]: Your BIOS is broken; bad RMRR
[0x000000006f760000-0x000000006f762fff]
Commit c347a787e34cb (drbd: set ->bi_bdev in drbd_req_new) moved a
bio_set_dev call (which has since been removed) to "earlier", from
drbd_request_prepare to drbd_req_new.
The problem is that this accesses device->ldev->backing_bdev, which is
not NULL-checked at this point. When we don't have an ldev (i.e. when
the DRBD device is diskless), this leads to a null pointer deref.
So, only allocate the private_bio if we actually have a disk. This is
also a small optimization, since we don't clone the bio to only to
immediately free it again in the diskless case.
Fixes: c347a787e34cb ("drbd: set ->bi_bdev in drbd_req_new") Co-developed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> Co-developed-by: Joel Colledge <joel.colledge@linbit.com> Signed-off-by: Joel Colledge <joel.colledge@linbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20221020085205.129090-1-christoph.boehmwalder@linbit.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the cable is disconnected the PHY seems to toggle between MDI and
MDI-X modes. With the MDI crossover status interrupt active this causes
roughly 10 interrupts per second.
As the crossover status isn't checked by the driver, the interrupt can
be disabled to reduce the interrupt load.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission") Signed-off-by: Felix Riemann <felix.riemann@sma.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20221018104755.30025-1-svc.sw.rte.linux@sma.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We had one syzbot report [1] in syzbot queue for a while.
I was waiting for more occurrences and/or a repro but
Dmitry Vyukov spotted the issue right away.
<quoting Dmitry>
qdisc_graft() drops reference to qdisc in notify_and_destroy
while it's still assigned to dev->qdisc
</quoting>
Indeed, RCU rules are clear when replacing a data structure.
The visible pointer (dev->qdisc in this case) must be updated
to the new object _before_ RCU grace period is started
(qdisc_put(old) in this case).
[1]
BUG: KASAN: use-after-free in __tcf_qdisc_find.part.0+0xa3a/0xac0 net/sched/cls_api.c:1066
Read of size 4 at addr ffff88802065e038 by task syz-executor.4/21027
The buggy address belongs to the object at ffff88802065e000
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 56 bytes inside of
1024-byte region [ffff88802065e000, ffff88802065e400)
Inject fault while probing module, if device_register() fails,
but the refcount of kobject is not decreased to 0, the name
allocated in dev_set_name() is leaked. Fix this by calling
put_device(), so that name can be freed in callback function
kobject_cleanup().
Inject fault while probing module, if device_register() fails,
but the refcount of kobject is not decreased to 0, the name
allocated in dev_set_name() is leaked. Fix this by calling
put_device(), so that name can be freed in callback function
kobject_cleanup().
Filters on different vports are qualified by different implicit MACs and/or
VLANs, so shouldn't be considered equal even if their other match fields
are identical.
Fixes: 7c460d9be610 ("sfc: Extend and abstract efx_filter_spec to cover Huntington/EF10") Co-developed-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com> Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/20221018092841.32206-1-pieter.jansen-van-vuuren@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We don't have a NULL check on file_ptr in io_msg_send_fd() function,
so when file_ptr is NUL src_file is also NULL and get_file()
dereferences a NULL pointer and leads to above crash.
Currently qdisc ingress handling (sch_handle_ingress()) doesn't
set a return value and it is left to the old return value of
the caller (__netif_receive_skb_core()) which is RX drop, so if
the packet is consumed, caller will stop and return this value
as if the packet was dropped.
This causes a problem in the kernel tcp stack when having a
egress tc rule forwarding to a ingress tc rule.
The tcp stack sending packets on the device having the egress rule
will see the packets as not successfully transmitted (although they
actually were), will not advance it's internal state of sent data,
and packets returning on such tcp stream will be dropped by the tcp
stack with reason ack-of-unsent-data. See reproduction in [0] below.
Fix that by setting the return value to RX success if
the packet was handled successfully.
[0] Reproduction steps:
$ ip link add veth1 type veth peer name peer1
$ ip link add veth2 type veth peer name peer2
$ ifconfig peer1 5.5.5.6/24 up
$ ip netns add ns0
$ ip link set dev peer2 netns ns0
$ ip netns exec ns0 ifconfig peer2 5.5.5.5/24 up
$ ifconfig veth2 0 up
$ ifconfig veth1 0 up
#ingress forwarding veth1 <-> veth2
$ tc qdisc add dev veth2 ingress
$ tc qdisc add dev veth1 ingress
$ tc filter add dev veth2 ingress prio 1 proto all flower \
action mirred egress redirect dev veth1
$ tc filter add dev veth1 ingress prio 1 proto all flower \
action mirred egress redirect dev veth2
#steal packet from peer1 egress to veth2 ingress, bypassing the veth pipe
$ tc qdisc add dev peer1 clsact
$ tc filter add dev peer1 egress prio 20 proto ip flower \
action mirred ingress redirect dev veth1
#run iperf and see connection not running
$ iperf3 -s&
$ ip netns exec ns0 iperf3 -c 5.5.5.6 -i 1
#delete egress rule, and run again, now should work
$ tc filter del dev peer1 egress
$ ip netns exec ns0 iperf3 -c 5.5.5.6 -i 1
Fixes: f697c3e8b35c ("[NET]: Avoid unnecessary cloning for ingress filtering") Signed-off-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the default qdisc is sfb, if the qdisc of dev_queue fails to be
inited during mqprio_init(), sfb_reset() is invoked to clear resources.
In this case, the q->qdisc is NULL, and it will cause gpf issue.
The process is as follows:
qdisc_create_dflt()
sfb_init()
tcf_block_get() --->failed, q->qdisc is NULL
...
qdisc_put()
...
sfb_reset()
qdisc_reset(q->qdisc) --->q->qdisc is NULL
ops = qdisc->ops
The following is the Call Trace information:
general protection fault, probably for non-canonical address
0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
RIP: 0010:qdisc_reset+0x2b/0x6f0
Call Trace:
<TASK>
sfb_reset+0x37/0xd0
qdisc_reset+0xed/0x6f0
qdisc_destroy+0x82/0x4c0
qdisc_put+0x9e/0xb0
qdisc_create_dflt+0x2c3/0x4a0
mqprio_init+0xa71/0x1760
qdisc_create+0x3eb/0x1000
tc_modify_qdisc+0x408/0x1720
rtnetlink_rcv_msg+0x38e/0xac0
netlink_rcv_skb+0x12d/0x3a0
netlink_unicast+0x4a2/0x740
netlink_sendmsg+0x826/0xcc0
sock_sendmsg+0xc5/0x100
____sys_sendmsg+0x583/0x690
___sys_sendmsg+0xe8/0x160
__sys_sendmsg+0xbf/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f2164122d04
</TASK>
Fixes: e13e02a3c68d ("net_sched: SFB flow scheduler") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
