The if (c >= 20 && c <= 0x3f) test added in commit 7a99565f8732 is
wrong. 20 is DC4 in ascii and it makes no sense to consider that as the
bottom limit. Instead, it should be 0x20 as in the other test in
the commit above. This is supposed to NOT change anything as we handle
interesting 20-0x20 asciis far before this if.
The sparse tool complains about the remove of the _iomem attribute.
stm32_rproc.c:660:17: warning: cast removes address space '__iomem' of expression
Add '__force' to explicitly specify that the cast is intentional.
This conversion is necessary to cast to addresses pointer,
which are then managed by the remoteproc core as a pointer to a
resource_table structure.
Add '__force' to explicitly specify that the cast is intentional.
This conversion is necessary to cast to virtual addresses pointer,used,
by the remoteproc core.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312150052.HCiNKlqB-lkp@intel.com/ Fixes: 13140de09cc2 ("remoteproc: stm32: add an ST stm32_rproc driver") Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Link: https://lore.kernel.org/r/20240117135312.3381936-2-arnaud.pouliquen@foss.st.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With CONFIG_ARCH_STM32 making it into arch/arm64, a couple of format
strings no longer work, since they rely on size_t being compatible
with %x, or they print an 'int' using %z:
drivers/remoteproc/stm32_rproc.c: In function 'stm32_rproc_mem_alloc':
drivers/remoteproc/stm32_rproc.c:122:22: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'size_t' {aka 'long unsigned int'} [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:122:40: note: format string is defined here
122 | dev_dbg(dev, "map memory: %pa+%x\n", &mem->dma, mem->len);
| ~^
| |
| unsigned int
| %lx
drivers/remoteproc/stm32_rproc.c:125:30: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'size_t' {aka 'long unsigned int'} [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:125:65: note: format string is defined here
125 | dev_err(dev, "Unable to map memory region: %pa+%x\n",
| ~^
| |
| unsigned int
| %lx
drivers/remoteproc/stm32_rproc.c: In function 'stm32_rproc_get_loaded_rsc_table':
drivers/remoteproc/stm32_rproc.c:646:30: error: format '%zx' expects argument of type 'size_t', but argument 4 has type 'int' [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:646:66: note: format string is defined here
646 | dev_err(dev, "Unable to map memory region: %pa+%zx\n",
| ~~^
| |
| long unsigned int
| %x
Fix up all three instances to work across architectures, and enable
compile testing for this driver to ensure it builds everywhere.
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Stable-dep-of: 32381bbccba4 ("remoteproc: stm32: Fix incorrect type in assignment for va") Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the setting of the resource table installed by an external
entity to rproc_ops::get_loaded_rsc_table(). This is to support
scenarios where a remote processor has been attached to but is
detached at a later stage. To re-attach the remote processor,
the address of the resource table needs to be available
at a later time than the platform driver's probe() function.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Link: https://lore.kernel.org/r/20210312162453.1234145-7-mathieu.poirier@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Stable-dep-of: 32381bbccba4 ("remoteproc: stm32: Fix incorrect type in assignment for va") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a new get_loaded_rsc_table() operation in order to support
scenarios where the remoteproc core has booted a remote processor
and detaches from it. When re-attaching to the remote processor,
the core needs to know where the resource table has been placed
in memory.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Link: https://lore.kernel.org/r/20210312162453.1234145-6-mathieu.poirier@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Stable-dep-of: 32381bbccba4 ("remoteproc: stm32: Fix incorrect type in assignment for va") Signed-off-by: Sasha Levin <sashal@kernel.org>
The only usage of st_rproc_ops is to pass its address to rproc_alloc()
which accepts a const pointer. Make it const to allow the compiler to
put it in read-only memory.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Link: https://lore.kernel.org/r/20201107233630.9728-3-rikard.falkeborn@gmail.com Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Stable-dep-of: 32381bbccba4 ("remoteproc: stm32: Fix incorrect type in assignment for va") Signed-off-by: Sasha Levin <sashal@kernel.org>
The intent is to check if 'dest' is truncated or not. So, >= should be
used instead of >, because strlcat() returns the length of 'dest' and 'src'
excluding the trailing NULL.
Fixes: 56463e50d1fc ("NFS: Use super.c for NFSROOT mount option parsing") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver never sets a default timeout value, therefore it is
initialized to zero. When CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is
enabled, the watchdog is started during probe. The kernel is supposed to
automatically ping the watchdog from this point until userspace takes
over, but this does not happen if the configured timeout is zero. A zero
timeout causes watchdog_need_worker() to return false, so the heartbeat
worker does not run and the system therefore resets soon after the
driver is probed.
This patch fixes this by setting an arbitrary non-zero default timeout.
The default could be read from the hardware instead, but I didn't see
any reason to add this complexity.
This has been tested on an STM32F746.
Fixes: 85fdc63fe256 ("drivers: watchdog: stm32_iwdg: set WDOG_HW_RUNNING at probe") Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20240228182723.12855-1-ben.wolsieffer@hefring.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Switch order of operations to avoid creating a short XDR buffer:
e.g., buflen = 12, old xdrlen = 12, new xdrlen = 20.
Having a short XDR buffer leads to lxa_maxcount be a few bytes
less than what is needed to retrieve the whole list when using
a buflen as returned by a call with size = 0:
buflen = listxattr(path, NULL, 0);
buf = malloc(buflen);
buflen = listxattr(path, buf, buflen);
For a file with one attribute (name = '123456'), the first call
with size = 0 will return buflen = 12 ('user.123456\x00').
The second call with size = 12, sends LISTXATTRS with
lxa_maxcount = 12 + 8 (cookie) + 4 (array count) = 24. The
XDR buffer needs 8 (cookie) + 4 (array count) + 4 (name count)
+ 6 (name len) + 2 (padding) + 4 (eof) = 28 which is 4 bytes
shorter than the lxa_maxcount provided in the call.
Fixes: 04a5da690e8f ("NFSv4.2: define limits and sizes for user xattr handling") Signed-off-by: Jorge Mora <mora@netapp.com> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A call to listxattr() with a buffer size = 0 returns the actual
size of the buffer needed for a subsequent call. When size > 0,
nfs4_listxattr() does not return an error because either
generic_listxattr() or nfs4_listxattr_nfs4_label() consumes
exactly all the bytes then size is 0 when calling
nfs4_listxattr_nfs4_user() which then triggers the following
kernel BUG:
The intent is to check if the strings' are truncated or not. So, >= should
be used instead of >, because strlcat() and snprintf() return the length of
the output, excluding the trailing NULL.
Fixes: a02d69261134 ("SUNRPC: Provide functions for managing universal addresses") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some callback functions used here take a boolean argument, others take a
status argument. This breaks KCFI type checking, so clang now warns about
the function pointer cast:
drivers/scsi/bfa/bfad_bsg.c:2138:29: error: cast from 'void (*)(void *, enum bfa_status)' to 'bfa_cb_cbfn_t' (aka 'void (*)(void *, enum bfa_boolean)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Assuming the code is actually correct here and the callers always match the
argument types of the callee, rework this to replace the explicit cast with
a union of the two pointer types. This does not change the behavior of the
code, so if something is actually broken here, a larger rework may be
necessary.
Fixes: 37ea0558b87a ("[SCSI] bfa: Added support to collect and reset fcport stats") Fixes: 3ec4f2c8bff2 ("[SCSI] bfa: Added support to configure QOS and collect stats.") Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20240222124433.2046570-1-arnd@kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mad_client will be initialized in enable_device_and_get(), while the
devices_rwsem will be downgraded to a read semaphore. There is a window
that leads to the failed initialization for cm_client, since it can not
get matched mad port from ib_mad_port_list, and the matched mad port will
be added to the list after that.
Fix it by using down_write(&devices_rwsem) in ib_register_client().
Fixes: d0899892edd0 ("RDMA/device: Provide APIs from the core code to help unregistration") Link: https://lore.kernel.org/r/20240203035313.98991-1-lishifeng@sangfor.com.cn Suggested-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
csiostor uses function pointer casts to keep the csio_ln_ev state machine
hidden, but this causes warnings about control flow integrity (KCFI)
violations in clang-16 and higher:
drivers/scsi/csiostor/csio_lnode.c:1098:33: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1098 | return (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1369:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1369 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_uninit)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1373:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1373 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1377:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1377 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_offline)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Move the enum into a shared header so the correct types can be used without
the need for casts.
Compressed cluster may not be released due to we can fail in
release_compress_blocks(), fix to handle reserved compressed
cluster correctly in reserve_compress_blocks().
Fixes: 4c8ff7095bef ("f2fs: support data compression") Signed-off-by: Sheng Yong <shengyong@oppo.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Upon rare occasions, KASAN reports a use-after-free Write
in srpt_refresh_port().
This seems to be because an event handler is registered before the
srpt device is fully setup and a race condition upon error may leave a
partially setup event handler in place.
Instead, only register the event handler after srpt device initialization
is complete.
Fixes: a42d985bd5b2 ("ib_srpt: Initial SRP Target merge for v3.3-rc1") Signed-off-by: William Kucharski <william.kucharski@oracle.com> Link: https://lore.kernel.org/r/20240202091549.991784-2-william.kucharski@oracle.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Realtek codec on HP Envy laptop series are heavily modified by vendor.
Therefore, need intervention to make it work properly. The patch fixes:
- B&O soundbar speakers (between lid and keyboard) activation
- Enable LED on mute button
- Add missing process coefficient which affects the output amplifier
- Volume control synchronization between B&O soundbar and side speakers
- Unmute headset output on several HP Envy models
- Auto-enable headset mic when plugged
This patch was tested on HP Envy x360 13-AR0107AU with Realtek ALC285
The only unsolved problem is output amplifier of all built-in speakers
is too weak, which causes volume of built-in speakers cannot be loud
as vendor's proprietary driver due to missing _DSD parameter in the
firmware. The solution is currently on research. Expected to has another
patch in the future.
Potential fix to related issues, need test before close those issues:
__clk_get_hw() can return NULL which is dereferenced by clk_core_get() at
hw->core.
Prior to commit dde4eff47c82 ("clk: Look for parents with clkdev based
clk_lookups") the check IS_ERR_OR_NULL() was performed which would have
caught the NULL.
Reading the description of this function it talks about returning NULL but
that cannot be so at the moment.
Update the function to check for hw before dereferencing it and return NULL
if hw is NULL.
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
Enabling strobe and then setting brightness to 0 causes the driver to enter
invalid state after strobe end timer fires. We should cancel strobe mode
resources when changing brightness (aka torch mode).
Fixes: cef8ec8cbd21 ("leds: add sgm3140 driver") Signed-off-by: Ondrej Jirman <megi@xff.cz> Link: https://lore.kernel.org/r/20240217191133.1757553-1-megi@xff.cz Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the probe() callback in case of error mutex is destroyed being locked
which is not allowed so unlock the mutex before destroying.
Fixes: 59ea3c9faf32 ("leds: add aw2013 driver") Signed-off-by: George Stark <gnstark@salutedevices.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20231214173614.2820929-2-gnstark@salutedevices.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the prototypes into mpc10x.h which is included by all the relevant
C files, fixes:
arch/powerpc/platforms/embedded6xx/ls_uart.c:59:6: error: no previous prototype for 'avr_uart_configure'
arch/powerpc/platforms/embedded6xx/ls_uart.c:82:6: error: no previous prototype for 'avr_uart_send'
Setting up the timing engine when the physical encoder has a split role
neglects dividing the drm_display_mode's hskew parameter. Let's fix this
since this must also be done in preparation for implementing YUV420 over
DP.
Running event hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
in one of the system throws below error:
---Logs---
# perf list | grep hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=?/[Kernel PMU event]
# perf stat -v -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event is not supported by the kernel.
failed to read counter hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
The above error is because of the hcall failure as required
permission "Enable Performance Information Collection" is not set.
Based on current code, single_gpci_request function did not check the
error type incase hcall fails and by default returns EINVAL. But we can
have other reasons for hcall failures like H_AUTHORITY/H_PARAMETER with
detail_rc as GEN_BUF_TOO_SMALL, for which we need to act accordingly.
Fix this issue by adding new checks in the single_gpci_request and
h_gpci_event_init functions.
Result after fix patch changes:
# perf stat -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Error:
No permission to enable hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event.
Fixes: 220a0c609ad1 ("powerpc/perf: Add support for the hv gpci (get performance counter info) interface") Reported-by: Akanksha J N <akanksha@linux.ibm.com> Signed-off-by: Kajol Jain <kjain@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240229122847.101162-1-kjain@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible that mtk_crtc->event is NULL in
mtk_drm_crtc_finish_page_flip().
pending_needs_vblank value is set by mtk_crtc->event, but in
mtk_drm_crtc_atomic_flush(), it's is not guarded by the same
lock in mtk_drm_finish_page_flip(), thus a race condition happens.
Consider the following case:
CPU1 CPU2
step 1:
mtk_drm_crtc_atomic_begin()
mtk_crtc->event is not null,
step 1:
mtk_drm_crtc_atomic_flush:
mtk_drm_crtc_update_config(
!!mtk_crtc->event)
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip:
lock
mtk_crtc->event set to null,
pending_needs_vblank set to false
unlock
pending_needs_vblank set to true,
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip called again,
pending_needs_vblank is still true
//null pointer
Instead of guarding the entire mtk_drm_crtc_atomic_flush(), it's more
efficient to just check if mtk_crtc->event is null before use.
When saa7146_register_device and saa7146_vv_init fails, budget_av_attach
should free the resources it allocates, like the error-handling of
ttpci_budget_init does. Besides, there are two fixme comment refers to
such deallocations.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
A previous patch worked around a KASAN issue in stv0367, now a similar
problem showed up with clang:
drivers/media/dvb-frontends/stv0367.c:1222:12: error: stack frame size (3624) exceeds limit (2048) in 'stv0367ter_set_frontend' [-Werror,-Wframe-larger-than]
1214 | static int stv0367ter_set_frontend(struct dvb_frontend *fe)
Rework the stv0367_writereg() function to be simpler and mark both
register access functions as noinline_for_stack so the temporary
i2c_msg structures do not get duplicated on the stack when KASAN_STACK
is enabled.
[Syzbot reported]
BUG: KASAN: slab-use-after-free in pvr2_context_set_notify+0x2c4/0x310 drivers/media/usb/pvrusb2/pvrusb2-context.c:35
Read of size 4 at addr ffff888113aeb0d8 by task kworker/1:1/26
[Analyze]
Task A set disconnect_flag = !0, which resulted in Task B's condition being met
and releasing mp, leading to this issue.
[Fix]
Place the disconnect_flag assignment operation after all code in pvr2_context_disconnect()
to avoid this issue.
Reported-and-tested-by: syzbot+ce750e124675d4599449@syzkaller.appspotmail.com Fixes: e5be15c63804 ("V4L/DVB (7711): pvrusb2: Fix race on module unload") Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Missing break statement in the ATOM_ARG_IMM case of a switch statement,
adds the missing break statement, ensuring that the program's control
flow is as intended.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/atom.c:323 atom_get_src_int() warn: ignoring unreachable code.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)") Cc: Jammy Zhou <Jammy.Zhou@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
mtd-ram can potentially be larger than 4GB. get_bitmask_order() uses
fls() that is not guaranteed to work with values larger than 32-bit.
Specifically on aarch64 fls() returns 0 when all 32 LSB bits are clear.
Use fls64() instead.
When the driver sets up the zpos property it sets the default zpos value
to the HW id of the plane. That is fine as such, but as on many DSS
versions the driver arranges the DRM planes in a different order than
the HW planes (to keep the non-scalable planes first), this leads to odd
initial zpos values. An example is J721e, where the initial zpos values
for DRM planes are 1, 3, 0, 2.
In theory the userspace should configure the zpos values properly when
using multiple planes, and in that sense the initial zpos values
shouldn't matter, but there's really no reason not to fix this and help
the userspace apps which don't handle zpos perfectly. In particular,
some versions of Weston seem to have issues dealing with the planes
with the current default zpos values.
So let's change the zpos values for the DRM planes to 0, 1, 2, 3.
Another option would be to configure the planes marked as primary planes
to zpos 0. On a two display system this would give us plane zpos values
of 0, 0, 1, 2. The end result and behavior would be very similar in this
option, and I'm not aware that this would actually help us in any way.
So, to keep the code simple, I opted for the 0, 1, 2, 3 values.
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca3726 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON") Fixes: b59e2ae3690c ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: f36e789a1f8d ("mfd: altera-sysmgr: Add SOCFPGA System Manager") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-4-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: 45330bb43421 ("mfd: syscon: Allow property as NULL in syscon_regmap_lookup_by_phandle") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-2-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside tegra_fb_create(), drm_gem_object_lookup() increments ref count of
the found object. But if the following size check fails then the last
found object's ref count should be put there as the unreferencing loop
can't detect this situation.
Found by Linux Verification Center (linuxtesting.org).
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
Currently coefficients are applied only once, since they don't change.
However, this is done before enable bit is set and thus it doesn't get
applied properly.
Fix that by applying coefficients after enable bit is set. While this
means that it will be done evey time, it doesn't bring much time
penalty.
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/t9015.c:274:4: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
274 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/aiu.c:243:12: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
243 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
Cycles is recognized as part of a hard coded metric in stat-shadow.c,
it may call print_metric_only with a NULL fmt string leading to a
segfault. Handle the NULL fmt explicitly.
Fixes: 088519f318be ("perf stat: Move the display functions to stat-display.c") Signed-off-by: Ian Rogers <irogers@google.com> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Cc: K Prateek Nayak <kprateek.nayak@amd.com> Cc: James Clark <james.clark@arm.com> Cc: Kaige Ye <ye@kaige.org> Cc: John Garry <john.g.garry@oracle.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240209204947.3873294-4-irogers@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit in Fixes changed the logic on how resources are released and
introduced a new switchtec_exit_pci() that need to be called explicitly in
order to undo a corresponding switchtec_init_pci().
This was done in the remove function, but not in the probe.
Dquot pointers in i_dquot array in the inode are protected by
dquot_srcu. Annotate the array pointers with __rcu, perform the locked
dereferences with srcu_dereference_check() instead of plain reads, and
set the array elements with rcu_assign_pointer().
Fixes: b9ba6f94b238 ("quota: remove dqptr_sem") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402061900.rTuYDlo6-lkp@intel.com/ Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240202081852.2514092-1-wangjianjian3@huawei.com>
Stable-dep-of: 179b8c97ebf6 ("quota: Fix rcu annotations of inode dquot pointers") Signed-off-by: Sasha Levin <sashal@kernel.org>
As Honza said, remove_inode_dquot_ref() currently does not release the
last dquot reference but instead adds the dquot to tofree_head list. This
is because dqput() can sleep while dropping of the last dquot reference
(writing back the dquot and calling ->release_dquot()) and that must not
happen under dq_list_lock. Now that dqput() queues the final dquot cleanup
into a workqueue, remove_inode_dquot_ref() can call dqput() unconditionally
and we can significantly simplify it.
Here we open code the simplified code of remove_inode_dquot_ref() into
remove_dquot_ref() and remove the function put_dquot_list() which is no
longer used.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-6-libaokun1@huawei.com>
Stable-dep-of: 179b8c97ebf6 ("quota: Fix rcu annotations of inode dquot pointers") Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to toggle the resets in a rapid fashion can lead to the changes
not actually arriving at the clock controller block when we expect them
to. This was observed at least on SM8250.
Read back the value after regmap_update_bits to ensure write completion.
The MT8192 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: d32f38f2a8fc ("pinctrl: mediatek: Add pinctrl driver for mt8192") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240131071910.3950450-2-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dvb_register_device, *pdvbdev is set equal to dvbdev, which is freed
in several error-handling paths. However, *pdvbdev is not set to NULL
after dvbdev's deallocation, causing use-after-frees in many places,
for example, in the following call chain:
When calling dvb_unregister_device, dmxdev->dvbdev (i.e. *pdvbdev in
dvb_register_device) could point to memory that had been freed in
dvb_register_device. Thereafter, this pointer is transferred to
kref_put and triggering a use-after-free.
The entity->name (i.e. name) is allocated in v4l2_m2m_register_entity
but isn't freed in its following error-handling paths. This patch
adds such deallocation to prevent memleak of entity->name.
Fixes: be2fff656322 ("media: add helpers for memory-to-memory media controller") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
In tpg_alloc, resources should be deallocated in each and every
error-handling paths, since they are allocated in for statements.
Otherwise there would be memleaks because tpg_free is called only when
tpg_alloc return 0.
Fixes: 63881df94d3e ("[media] vivid: add the Test Pattern Generator") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Static analyzers generate alerts for an unchecked call to
`media_device_register()`. However, in this case, the device will work
reliably without the media controller API.
Add a comment above the call to prevent future unnecessary changes.
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d71 ("drm/amd/display: add null checks before logging") Cc: Wyatt Wood <wyatt.wood@amd.com> Cc: Anthony Koo <Anthony.Koo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tell snprintf() to store at most 10 bytes in the output buffer
instead of 30.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_debugfs.c:1508 dp_dsc_clock_en_read() error: snprintf() is printing too much 30 vs 10
Fixes: c06e09b76639 ("drm/amd/display: Add DSC parameters logging to debugfs") Cc: Alex Hung <alex.hung@amd.com> Cc: Qingqing Zhuo <qingqing.zhuo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous attempt to autodetect well-behaving patched firmware
introduced in commit 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw
on cptkbd and stop applying workaround") has shown that there are
false-positives on original firmware (on both 1st gen and 2nd gen
keyboards) which causes the middle button click workaround to be
mistakenly disabled.
This commit adds explicit parameter to sysfs to control this
workaround.
Fixes: 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround") Fixes: 43527a0094c1 ("HID: lenovo: Restrict detection of patched firmware only to USB cptkbd") Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
perf_data__switch() may not assign a legal value to 'new_filename'.
In this case, 'new_filename' uses the on-stack value, which may cause a
incorrect free and unexpected result.
Fixes: 03724b2e9c45 ("perf record: Allow to limit number of reported perf.data files") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240119040304.3708522-2-yangjihong1@huawei.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TLP Prefix Log Register consists of multiple DWORDs (PCIe r6.1 sec
7.9.14.13) but the loop in dpc_process_rp_pio_error() keeps reading from
the first DWORD, so we print only the first PIO TLP Prefix (duplicated
several times), and we never print the second, third, etc., Prefixes.
Add the iteration count based offset calculation into the config read.
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just T210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes 210 you don't get
this driver.
Fixes: 433de642a76c9 ("dmaengine: tegra210-adma: add support for Tegra186/Tegra194") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Cc: Sameer Pujar <spujar@nvidia.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20240112093310.329642-2-pbrobinson@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This scary message can misled the user into thinking something bad has
happened and needs to be fixed, however it could simply be part of a
normal boot process where EPROBE_DEFER is taken into account. Therefore,
let's use dev_err_probe so that this message doesn't get shown (by
default) when the return code is EPROBE_DEFER.
ret variable stores the return value of drm_of_find_panel_or_bridge
which can return error codes different from EPROBE_DEFER. Therefore,
let's just return that error code instead of forcing it to EPROBE_DEFER.
Unit testing this in VKMS shows that passing 0 into
this function returns -1, which is highly counter-
intuitive. Fix it by checking whether the input is
>= 0 instead of > 0.
Fixes: 64566b5e767f ("drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil") Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Simon Ser <contact@emersion.fr> Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231108163647.106853-2-harry.wentland@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller wants the difference between *total and *sync_start in the
HDMI_VIDEO_EXT_*DELAY registers. Otherwise the signal is very unstable for
certain non-VIC modes. See downstream commit [0].
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Stable-dep-of: 830c1ded3563 ("drm/tegra: dsi: Fix some error handling paths in tegra_dsi_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
There is this reported crash when experimenting with the lvm2 testsuite.
The list corruption is caused by the fact that the postsuspend and resume
methods were not paired correctly; there were two consecutive calls to the
origin_postsuspend function. The second call attempts to remove the
"hash_list" entry from a list, while it was already removed by the first
call.
Fix __dm_internal_resume so that it calls the preresume and resume
methods of the table's targets.
If a preresume method of some target fails, we are in a tricky situation.
We can't return an error because dm_internal_resume isn't supposed to
return errors. We can't return success, because then the "resume" and
"postsuspend" methods would not be paired correctly. So, we set the
DMF_SUSPENDED flag and we fake normal suspend - it may confuse userspace
tools, but it won't cause a kernel crash.
An empty flush doesn't have a payload, so it should never be looked at
when considering to possibly requeue a bio for the case when a reshape
is in progress.
Fixes: 9dbd1aa3a81c ("dm raid: add reshaping support to the target") Reported-by: Patrick Plenefisch <simonpatp@gmail.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d031140 ("nfp: flower: monitor and offload LAG groups") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
