Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b649 ("net: ip: push gso skb forwarding handling down the stack") Reported-by: Jan Tluka <jtluka@redhat.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: never had the IPSKB_FRAG_SEGS flag] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Like other KVM switches, the Aten DVI KVM switch needs a quirk to avoid spewing
errors:
[791759.606542] usb 1-5.4: input irq status -75 received
[791759.614537] usb 1-5.4: input irq status -75 received
[791759.622542] usb 1-5.4: input irq status -75 received
Add it.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
RFC 2734 defines the datagram_size field in fragment encapsulation
headers thus:
datagram_size: The encoded size of the entire IP datagram. The
value of datagram_size [...] SHALL be one less than the value of
Total Length in the datagram's IP header (see STD 5, RFC 791).
Accordingly, the eth1394 driver of Linux 2.6.36 and older set and got
this field with a -/+1 offset:
Likewise, I observe OS X 10.4 and Windows XP Pro SP3 to transmit 1500
byte sized datagrams in fragments with datagram_size=1499 if link
fragmentation is required.
Only firewire-net sets and gets datagram_size without this offset. The
result is lacking interoperability of firewire-net with OS X, Windows
XP, and presumably Linux' eth1394. (I did not test with the latter.)
For example, FTP data transfers to a Linux firewire-net box with max_rec
smaller than the 1500 bytes MTU
- from OS X fail entirely,
- from Win XP start out with a bunch of fragmented datagrams which
time out, then continue with unfragmented datagrams because Win XP
temporarily reduces the MTU to 576 bytes.
So let's fix firewire-net's datagram_size accessors.
Note that firewire-net thereby loses interoperability with unpatched
firewire-net, but only if link fragmentation is employed. (This happens
with large broadcast datagrams, and with large datagrams on several
FireWire CardBus cards with smaller max_rec than equivalent PCI cards,
and it can be worked around by setting a small enough MTU.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We have one critical section in the syscall entry path in which we switch from
the userspace stack to kernel stack. In the event of an external interrupt, the
interrupt code distinguishes between those two states by analyzing the value of
sr7. If sr7 is zero, it uses the kernel stack. Therefore it's important, that
the value of sr7 is in sync with the currently enabled stack.
This patch now disables interrupts while executing the critical section. This
prevents the interrupt handler to possibly see an inconsistent state which in
the worst case can lead to crashes.
Interestingly, in the syscall exit path interrupts were already disabled in the
critical section which switches back to the userspace stack.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
skb->cb may contain data from previous layers. In the observed scenario,
the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so
that small packets sent through the tunnel are mistakenly fragmented.
This patch unconditionally clears the control buffer in ip6tunnel_xmit(),
which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of
these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier.
Signed-off-by: Eli Cooper <elicooper@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to drop the reference taken by class_find_device() after
opening the RTC device.
Fixes: 77437fd4e61f (pm: boot time suspend selftest) Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This fixes the irq allocation in this driver to not print:
irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
Which happens because the driver already called irq_alloc_descs()
and so the change to use irq_domain_add_simple resulted in calling
irq_alloc_descs() twice.
Modernize the irq allocation in this driver to use the
irq_domain_add_linear flow directly and eliminate the use of
irq_domain_add_simple/legacy
Fixes: ce931f571b6d ("gpio/mvebu: convert to use irq_domain_add_simple()") Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16:
- Keep using irq_set_handler_data(), irq_set_chained_handler()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This subsystem consistently fails to drop the device reference taken by
class_find_device().
Note that some of these lookup functions already take a reference to the
returned data, while others claim no reference is needed (or does not
seem need one).
Fixes: 183b9b592a62 ("uwb: add the UWB stack (core files)") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
According to Dave Miller "the networking stack has a
hard requirement that all SKBs which are transmitted
must have their completion signalled in a fininte
amount of time. This is because, until the SKB is
freed by the driver, it holds onto socket,
netfilter, and other subsystem resources."
In summary, this means that using TX IRQ throttling
for the networking gadgets is, at least, complex and
we should avoid it for the time being.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.16: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today. I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.
On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.
This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com> Fixes: 56ceecde1f29 ("bgmac: initialize the DMA controller of core...") Cc: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Andrey Konovalov reported an issue with proc_register in bcm.c.
As suggested by Cong Wang this patch adds a lock_sock() protection and
a check for unsuccessful proc_create_data() in bcm_connect().
Similar to commit c146066ab802 ("ipv4: Don't use ufo handling on later
transformed packets"), don't perform UFO on packets that will be IPsec
transformed. To detect it we rely on the fact that headerlen in
dst_entry is non-zero only for transformation bundles (xfrm_dst
objects).
Unwanted segmentation can be observed with a NETIF_F_UFO capable device,
such as a dummy device:
DEV=dum0 LEN=1493
ip li add $DEV type dummy
ip addr add fc00::1/64 dev $DEV nodad
ip link set $DEV up
ip xfrm policy add dir out src fc00::1 dst fc00::2 \
tmpl src fc00::1 dst fc00::2 proto esp spi 1
ip xfrm state add src fc00::1 dst fc00::2 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
Fixes: e89e9cf539a2 ("[IPv4/IPv6]: UFO Scatter-gather approach") Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
NFC version reply size checked against only header size, not against
full message size. That may lead potentially to uninitialized memory access
in version data.
That leads to warnings when version data is accessed:
drivers/misc/mei/bus-fixup.c: warning: '*((void *)&ver+11)' may be used uninitialized in this function [-Wuninitialized]: => 212:2
Reported in
Build regressions/improvements in v4.9-rc3
https://lkml.org/lkml/2016/10/30/57
Fixes: 59fcd7c63abf (mei: nfc: Initial nfc implementation) Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- Drop change in mei_phy.c
- Adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When the memory is exhausted, then we will fail to add the NFT_MSG_NEWSET
transaction. In such case, we should destroy the set before we free it.
Fixes: 958bee14d071 ("netfilter: nf_tables: use new transaction infrastructure to handle sets") Signed-off-by: Liping Zhang <zlpnobody@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit c6017e793b93 ("virtio: console: add locks around buffer removal
in port unplug path") added locking around the freeing of buffers in the
vq. However, when free_buf() is called with can_sleep = true and rproc
is enabled, it calls dma_free_coherent() directly, requiring interrupts
to be enabled. Currently a WARNING is triggered due to the spin locking
around free_buf, with a call stack like this:
Fix this by restructuring the loops to allow the locks to only be taken
where it is necessary to protect the vqs, and release it while the
buffer is being freed.
Fixes: c6017e793b93 ("virtio: console: add locks around buffer removal in port unplug path") Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The VT-d specification (§8.3.3) says:
‘Virtual Functions’ of a ‘Physical Function’ are under the scope
of the same remapping unit as the ‘Physical Function’.
The BIOS is not required to list all the possible VFs in the scope
tables, and arguably *shouldn't* make any attempt to do so, since there
could be a huge number of them.
This has been broken basically for ever — the VF is never going to match
against a specific unit's scope, so it ends up being assigned to the
INCLUDE_ALL IOMMU. Which was always actually correct by coincidence, but
now we're looking at Root-Complex integrated devices with SR-IOV support
it's going to start being wrong.
Fix it to simply use pci_physfn() before doing the lookup for PCI devices.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com> Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The current ndelay() macro definition has an extra semi-colon at the
end of the line thus leading to a compilation error when ndelay is used
in a conditional block without curly braces like this one:
if (cond)
ndelay(t);
else
...
which, after the preprocessor pass gives:
if (cond)
m68k_ndelay(t);;
else
...
thus leading to the following gcc error:
error: 'else' without a previous 'if'
Remove this extra semi-colon.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: c8ee038bd1488 ("m68k: Implement ndelay() based on the existing udelay() logic") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.
At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP. On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.
The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.
Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.
Fixes: f9baff509f8a ("mlx4_core: Add "native" argument to mlx4_cmd ...") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: mlx4_en_DUMP_ETH_STATS() only uses this command once] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.
Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When doing roundup_pow_of_two for large enough number with
bit 31, an overflow will occur and a value equal to 1 will
be returned. In this case 1 will be subtracted from the return
value and division by zero will be reached.
Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency") Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The resource type enum in the resource tracker was incorrect.
RES_EQ was put in the position of RES_NPORT_ID (a FC resource).
Since the remaining resources maintain their current values,
and RES_EQ is not passed from slaves to the hypervisor in any
FW command, this change affects only the hypervisor.
Therefore, there is no backwards-compatibility issue.
Fixes: 623ed84b1f95 ("mlx4_core: initial header-file changes for SRIOV support") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When transmitting on a packet socket with PACKET_VNET_HDR and
PACKET_QDISC_BYPASS, validate device support for features requested
in vnet_hdr.
Drop TSO packets sent to devices that do not support TSO or have the
feature disabled. Note that the latter currently do process those
packets correctly, regardless of not advertising the feature.
Because of SKB_GSO_DODGY, it is not sufficient to test device features
with netif_needs_gso. Full validate_xmit_skb is needed.
Switch to software checksum for non-TSO packets that request checksum
offload if that device feature is unsupported or disabled. Note that
similar to the TSO case, device drivers may perform checksum offload
correctly even when not advertising it.
When switching to software checksum, packets hit skb_checksum_help,
which has two BUG_ON checksum not in linear segment. Packet sockets
always allocate at least up to csum_start + csum_off + 2 as linear.
Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c
Fixes: d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: open-code the necessary checks as we don't have
validate_xmit_skb_list()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently the firmware can't work with a page with dma address 0.
Passing such an address to the firmware will cause the give_pages
command to fail.
To avoid this, in case we get a 0 dma address of a page from the
dma engine, we avoid passing it to FW by remapping to get an address
other than 0.
Fixes: bf0bf77f6519 ('mlx5: Support communicating arbitrary host...') Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
mddev->curr_resync usually records where the current resync is up to,
but during the starting phase it has some "magic" values.
1 - means that the array is trying to start a resync, but has yielded
to another array which shares physical devices, and also needs to
start a resync
2 - means the array is trying to start resync, but has found another
array which shares physical devices and has already started resync.
3 - means that resync has commensed, but it is possible that nothing
has actually been resynced yet.
It is important that this value not be visible to user-space and
particularly that it doesn't get written to the metadata, as the
resync or recovery checkpoint. In part, this is because it may be
slightly higher than the correct value, though this is very rare.
In part, because it is not a multiple of 4K, and some devices only
support 4K aligned accesses.
There are two places where this value is propagates into either
->curr_resync_completed or ->recovery_cp or ->recovery_offset.
These currently avoid the propagation of values 1 and 3, but will
allow 3 to leak through.
Change them to only propagate the value if it is > 3.
As this can cause an array to fail, the patch is suitable for -stable.
Reported-by: Viswesh <viswesh.vichu@gmail.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
[bwh: Backported to 3.16: there is only one comparison to fix] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit c83ed4c9dbb35 ("ubifs: Abort readdir upon error") broke
overlayfs support because the fix exposed an internal error
code to VFS.
Reported-by: Peter Rosin <peda@axentia.se> Tested-by: Peter Rosin <peda@axentia.se> Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com> Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com> Fixes: c83ed4c9dbb35 ("ubifs: Abort readdir upon error") Signed-off-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When interrupting an application which was allocating DMAable
memory, it was possible, that the DMA memory was deallocated
twice, leading to the error symptoms below.
Thanks to Gerald, who analyzed the problem and provided this
patch.
I agree with his analysis of the problem: ddcb_cmd_fixups() ->
genwqe_alloc_sync_sgl() (fails in f/lpage, but sgl->sgl != NULL
and f/lpage maybe also != NULL) -> ddcb_cmd_cleanup() ->
genwqe_free_sync_sgl() (double free, because sgl->sgl != NULL and
f/lpage maybe also != NULL)
In this scenario we would have exactly the kind of double free that
would explain the WARNING / Bad page state, and as expected it is
caused by broken error handling (cleanup).
Using the Ubuntu git source, tag Ubuntu-4.4.0-33.52, he was able to reproduce
the "Bad page state" issue, and with the patch on top he could not reproduce
it any more.
vcpu->arch.wbinvd_dirty_mask may still be used after freeing it,
corrupting memory. For example, the following call trace may set a bit
in an already freed cpu mask:
kvm_arch_vcpu_load
vcpu_load
vmx_free_vcpu_nested
vmx_free_vcpu
kvm_arch_vcpu_free
Fix this by deferring freeing of wbinvd_dirty_mask.
Signed-off-by: Ido Yariv <ido@wizery.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since commit d86bd1bece6f ("mm/slub: support left redzone") it is no longer
guaranteed that kmalloc(PAGE_SIZE) returns page aligned memory.
After the above commit we get an error for diag224 because aligned
memory is required. This leads to the following user visible error:
# mount none -t s390_hypfs /sys/hypervisor/
mount: unknown filesystem type 's390_hypfs'
# dmesg | grep hypfs
hypfs.cccfb8: The hardware system does not provide all functions
required by hypfs
hypfs.7a79f0: Initialization of hypfs failed with rc=-61
Fix this problem and use get_free_page() instead of kmalloc() to get
correctly aligned memory.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
gen_pool_alloc_algo() iterates over the chunks of a pool trying to find
a contiguous block of memory that satisfies the allocation request.
The shortcut
if (size > atomic_read(&chunk->avail))
continue;
makes the loop skip over chunks that do not have enough bytes left to
fulfill the request. There are two situations, though, where an
allocation might still fail:
(1) The available memory is not contiguous, i.e. the request cannot
be fulfilled due to external fragmentation.
(2) A race condition. Another thread runs the same code concurrently
and is quicker to grab the available memory.
In those situations, the loop calls pool->algo() to search the entire
chunk, and pool->algo() returns some value that is >= end_bit to
indicate that the search failed. This return value is then assigned to
start_bit. The variables start_bit and end_bit describe the range that
should be searched, and this range should be reset for every chunk that
is searched. Today, the code fails to reset start_bit to 0. As a
result, prefixes of subsequent chunks are ignored. Memory allocations
might fail even though there is plenty of room left in these prefixes of
those other chunks.
Fixes: 7f184275aa30 ("lib, Make gen_pool memory allocator lockless") Link: http://lkml.kernel.org/r/1477420604-28918-1-git-send-email-danielmentz@google.com Signed-off-by: Daniel Mentz <danielmentz@google.com> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
btrfs_remove_all_log_ctxs takes a shortcut where it avoids walking the
list because it knows all of the waiters are patiently waiting for the
commit to finish.
But, there's a small race where btrfs_sync_log can remove itself from
the list if it finds a log commit is already done. Also, it uses
list_del_init() to remove itself from the list, but there's no way to
know if btrfs_remove_all_log_ctxs has already run, so we don't know for
sure if it is safe to call list_del_init().
This gets rid of all the shortcuts for btrfs_remove_all_log_ctxs(), and
just calls it with the proper locking.
This is part two of the corruption fixed by cbd60aa7cd1. I should have
done this in the first place, but convinced myself the optimizations were
safe. A 12 hour run of dbench 2048 will eventually trigger a list debug
WARN_ON for the list_del_init() in btrfs_sync_log().
Fixes: d1433debe7f4346cf9fc0dafc71c3137d2a97bc4 Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 36b701fae12ac ("netfilter: nf_tables: validate maximum value of
u32 netlink attributes") introduced nft_parse_u32_check with a return
value of "unsigned int", yet on error it returns "-ERANGE".
This patch corrects the mismatch by changing the return value to "int",
which happens to match the actual users of nft_parse_u32_check already.
Note that commit 21a9e0f1568ea ("netfilter: nft_exthdr: fix error
handling in nft_exthdr_init()) attempted to address the issue, but
did not address the return type of nft_parse_u32_check.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Laura Garcia Liebana <nevola@gmail.com> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 36b701fae12ac ("netfilter: nf_tables: validate maximum value...") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
on SIP requests, so a fragmented TCP SIP packet from an allow header starting with
INVITE,NOTIFY,OPTIONS,REFER,REGISTER,UPDATE,SUBSCRIBE
Content-Length: 0
will not bet interpreted as an INVITE request. Also Request-URI must start with an alphabetic character.
Size of kmalloc() in vc_do_resize() is controlled by user.
Too large kmalloc() size triggers WARNING message on console.
Put a reasonable upper bound on terminal size to prevent WARNINGs.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com> CC: David Rientjes <rientjes@google.com> Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: linux-kernel@vger.kernel.org Cc: syzkaller@googlegroups.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is
divided by 2 inappropriatelly. But scr_memsetw expects size, not
count, because it divides the size by 2 on its own before doing actual
memset-by-words.
The stk1160 chip needs QUIRK_AUDIO_ALIGN_TRANSFER. This patch resolves
the issue reported on the mailing list
(http://marc.info/?l=linux-sound&m=139223599126215&w=2) and also fixes
bug 180071 (https://bugzilla.kernel.org/show_bug.cgi?id=180071).
The arcmsr driver failed to pass SYNCHRONIZE CACHE to controller
firmware. Depending on how drive caches are handled internally by
controller firmware this could potentially lead to data integrity
problems.
Ensure that cache flushes are passed to the controller.
[mkp: applied by hand and removed unused vars]
Signed-off-by: Ching Huang <ching2048@areca.com.tw> Reported-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
map_storep was not being vfree()'d in the module_exit call.
Signed-off-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Consolidate existing quirks. Fixes stability issues
on some kickers.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The advancing of the PC when completing an MMIO load is done before
re-entering the guest, i.e. before restoring the guest ASID. However if
the load is in a branch delay slot it may need to access guest code to
read the prior branch instruction. This isn't safe in TLB mapped code at
the moment, nor in the future when we'll access unmapped guest segments
using direct user accessors too, as it could read the branch from host
user memory instead.
Therefore calculate the resume PC in advance while we're still in the
right context and save it in the new vcpu->arch.io_pc (replacing the no
longer needed vcpu->arch.pending_load_cause), and restore it on MMIO
completion.
Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As kvm_mips_complete_mmio_load() did not yet modify PC at this point
as James Hogans <james.hogan@imgtec.com> explained the curr_pc variable
and the comments along with it can be dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Link: http://lkml.org/lkml/2015/5/8/422 Cc: Gleb Natapov <gleb@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9993/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ERET instruction to return from exception is used for returning from
exception level (Status.EXL) and error level (Status.ERL). If both bits
are set however we should be returning from ERL first, as ERL can
interrupt EXL, for example when an NMI is taken. KVM however checks EXL
first.
Fix the order of the checks to match the pseudocode in the instruction
set manual.
Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The read is taking a considerable amount of time (about 50us on this
machine). The register does not ever hold anything other than the ring
ID that is updated in this exact function, so there is no need for
the read modify write cycle.
This chops off a big chunk of the time spent in hardirq disabled
context, as this function is called multiple times in the interrupt
handler. With this change applied radeon won't show up in the list
of the worst IRQ latency offenders anymore, where it was a regular
before.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ad5933_i2c_read function returns an error code to indicate
whether it could read data or not. However ad5933_work() ignores
this return code and just accesses the data unconditionally,
which gets detected by gcc as a possible bug:
drivers/staging/iio/impedance-analyzer/ad5933.c: In function 'ad5933_work':
drivers/staging/iio/impedance-analyzer/ad5933.c:649:16: warning: 'status' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds minimal error handling so we only evaluate the
data if it was correctly read.
Link: https://patchwork.kernel.org/patch/8110281/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ASRock B150M Pro4/D3 mobo with ALC892 codec doesn't seem to provide
proper pins for the surround outputs, hence we need to specify the
pincfgs manually with a couple of other corrections.
Reported-and-tested-by: Benjamin Valentin <benpicco@googlemail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The host keeps sending heartbeat packets independent of the
guest responding to them. Even though we respond to the heartbeat messages at
interrupt level, we can have situations where there maybe multiple heartbeat
messages pending that have not been responded to. For instance this occurs when the
VM is paused and the host continues to send the heartbeat messages.
Address this issue by draining and responding to all
the heartbeat messages that maybe pending.
Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 02b01e010afe ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010afeeb49328d35650d70721d2ca3fd59 Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
SEC registers are not accessible when the TXE device is in low power
state, hence the SEC interrupt cannot be processed if device is not
awake.
In some rare cases entrance to low power state (aliveness off) and input
ready bits can be signaled at the same time, resulting in communication
stall as input ready won't be signaled again after waking up. To resolve
this IPC_HHIER_SEC bit in HHISR_REG should not be cleaned if the
interrupt is not processed.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
dm_get_target_type() was previously called so any error returned from
dm_table_add_target() must first call dm_put_target_type(). Otherwise
the DM target module's reference count will leak and the associated
kernel module will be unable to be removed.
Also, leverage the fact that r is already -EINVAL and remove an extra
newline.
This reverts commit a681574c99be23e4d20b769bf0e543239c364af5
("ipv4: disable BH in set_ping_group_range()") because we never
read ping_group_range in BH context (unlike local_port_range).
Then, since we already have a lock for ping_group_range, those
using ip_local_ports.lock for ping_group_range are clearly typos.
We might consider to share a same lock for both ping_group_range
and local_port_range w.r.t. space saving, but that should be for
net-next.
Fixes: a681574c99be ("ipv4: disable BH in set_ping_group_range()") Fixes: ba6b918ab234 ("ping: move ping_group_range out of CONFIG_SYSCTL") Cc: Eric Dumazet <edumazet@google.com> Cc: Eric Salo <salo@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: we never applied "ipv4: disable BH in
set_ping_group_range()"] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
PowerPC's "cmp" instruction has four operands. Normally people write
"cmpw" or "cmpd" for the second cmp operand 0 or 1. But, frequently
people forget, and write "cmp" with just three operands.
With older binutils this is silently accepted as if this was "cmpw",
while often "cmpd" is wanted. With newer binutils GAS will complain
about this for 64-bit code. For 32-bit code it still silently assumes
"cmpw" is what is meant.
In this instance the code comes directly from ISA v2.07, including the
cmp, but cmpd is correct. Backport to stable so that new toolchains can
build old kernels.
Fixes: 948cf67c4726 ("powerpc: Add NAP mode support on Power7 in HV mode") Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The WnR bit in the HSR/ESR_EL2 indicates whether a data abort was
generated by a read or a write instruction. For stage 2 data aborts
generated by a stage 1 translation table walk (i.e. the actual page
table access faults at EL2), the WnR bit therefore reports whether the
instruction generating the walk was a load or a store, *not* whether the
page table walker was reading or writing the entry.
For page tables marked as read-only at stage 2 (e.g. due to KSM merging
them with the tables from another guest), this could result in livelock,
where a page table walk generated by a load instruction attempts to
set the access flag in the stage 1 descriptor, but fails to trigger
CoW in the host since only a read fault is reported.
This patch modifies the arm64 kvm_vcpu_dabt_iswrite function to
take into account stage 2 faults in stage 1 walks. Since DBM cannot be
disabled at EL2 for CPUs that implement it, we assume that these faults
are always causes by writes, avoiding the livelock situation at the
expense of occasional, spurious CoWs.
We could, in theory, do a bit better by checking the guest TCR
configuration and inspecting the page table to see why the PTE faulted.
However, I doubt this is measurable in practice, and the threat of
livelock is real.
Cc: Julien Grall <julien.grall@arm.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
[bwh: Backported to 3.16:
- Keep using ESR_EL2_WNR in the first part of the condition
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Limit clocks on a specific HD86xx part to avoid
crashes (while awaiting an appropriate PP fix).
Signed-off-by: Tom St Denis <tom.stdenis@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure we have at least one port before attempting to register a
console.
Currently, at least one driver binds to a "dummy" interface and requests
zero ports for it. Should such an interface also lack endpoints, we get
a NULL-deref during probe.
Fixes: e5b1e2062e05 ("USB: serial: make minor allocation dynamic") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch addresses a bug where a local EXTENDED_COPY WRITE or READ
backend I/O request would always return SAM_STAT_CHECK_CONDITION,
even if underlying xcopy_pt_cmd->se_cmd generated a different
SCSI status code.
ESX host environments expect to hit SAM_STAT_RESERVATION_CONFLICT
for certain scenarios, and SAM_STAT_CHECK_CONDITION results in
non-retriable status for these cases.
Tested on v4.1.y with ESX v5.5u2+ with local IBLOCK backend copy.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Cc: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Dinesh Israni <ddi@datera.io> Signed-off-by: Dinesh Israni <ddi@datera.io> Cc: Dinesh Israni <ddi@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch addresses a bug where EXTENDED_COPY across multiple LUNs
results in a CHECK_CONDITION when the source + destination are not
located on the same physical node.
ESX Host environments expect sense COPY_ABORTED w/ COPY TARGET DEVICE
NOT REACHABLE to be returned when this occurs, in order to signal
fallback to local copy method.
As described in section 6.3.3 of spc4r22:
"If it is not possible to complete processing of a segment because the
copy manager is unable to establish communications with a copy target
device, because the copy target device does not respond to INQUIRY,
or because the data returned in response to INQUIRY indicates
an unsupported logical unit, then the EXTENDED COPY command shall be
terminated with CHECK CONDITION status, with the sense key set to
COPY ABORTED, and the additional sense code set to COPY TARGET DEVICE
NOT REACHABLE."
Tested on v4.1.y with ESX v5.5u2+ with BlockCopy across multiple nodes.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com> Cc: Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by: Dinesh Israni <ddi@datera.io> Signed-off-by: Dinesh Israni <ddi@datera.io> Cc: Dinesh Israni <ddi@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.16: generate the sense data in
transport_send_check_condition_and_sense() rather than adding to
sense_info_table] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If UBIFS is facing an error while walking a directory, it reports this
error and ubifs_readdir() returns the error code. But the VFS readdir
logic does not make the getdents system call fail in all cases. When the
readdir cursor indicates that more entries are present, the system call
will just return and the libc wrapper will try again since it also
knows that more entries are present.
This causes the libc wrapper to busy loop for ever when a directory is
corrupted on UBIFS.
A common approach do deal with corrupted directory entries is
skipping them by setting the cursor to the next entry. On UBIFS this
approach is not possible since we cannot compute the next directory
entry cursor position without reading the current entry. So all we can
do is setting the cursor to the "no more entries" position and make
getdents exit.
Signed-off-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The Schenker XMG C504 is a rebranded Gigabyte P35 v2 laptop.
Therefore it also needs a keyboard reset to detect the Elantech touchpad.
Otherwise the touchpad appears to be dead.
With this patch the touchpad is detected:
$ dmesg | grep -E "(i8042|Elantech|elantech)"
[ 2.675399] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.680372] i8042: Attempting to reset device connected to KBD port
[ 2.789037] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.791586] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.813840] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 3.811431] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f0e)
[ 3.825424] psmouse serio1: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0f.
[ 3.839424] psmouse serio1: elantech: Elan sample query result 03, 58, 74
[ 3.911349] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input6
Signed-off-by: Patrick Scheuring <patrick.scheuring.dev@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
hw_random carefully avoids using a stack buffer except in
add_early_randomness(). This causes a crash in virtio_rng if
CONFIG_VMAP_STACK=y.
Reported-by: Matt Mullins <mmullins@mmlx.us> Tested-by: Matt Mullins <mmullins@mmlx.us> Fixes: d3cc7996473a ("hwrng: fetch randomness only after device init") Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Satish reported a problem with the perm multicast router ports not getting
reenabled after some series of events, in particular if it happens that the
multicast snooping has been disabled and the port goes to disabled state
then it will be deleted from the router port list, but if it moves into
non-disabled state it will not be re-added because the mcast snooping is
still disabled, and enabling snooping later does nothing.
Here are the steps to reproduce, setup br0 with snooping enabled and eth1
added as a perm router (multicast_router = 2):
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
<empty>
At this point we have mcast enabled and eth1 as a perm router (value = 2)
but it is not in the router list which is incorrect.
After this change:
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
router ports on br0: eth1
Note: we can directly do br_multicast_enable_port for all because the
querier timer already has checks for the port state and will simply
expire if it's in blocking/disabled. See the comment added by
commit 9aa66382163e7 ("bridge: multicast: add a comment to
br_port_state_selection about blocking state")
Fixes: 561f1103a2b7 ("bridge: Add multicast_snooping sysfs toggle") Reported-by: Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When isofs_mount() is called to mount a device read-write, it returns
EACCES even before it checks that the device actually contains an isofs
filesystem. This may confuse mount(8) which then tries to mount all
subsequent filesystem types in read-only mode.
Fix the problem by returning EACCES only once we verify that the device
indeed contains an iso9660 filesystem.
Fixes: 17b7f7cf58926844e1dd40f5eb5348d481deca6a Reported-by: Kent Overstreet <kent.overstreet@gmail.com> Reported-by: Karel Zak <kzak@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 49d9e77e72cf ("ALSA: hda - Fix system panic when DMA > 40 bits
for Nvidia audio controllers") simply disabled any DMA exceeding 32
bits for NVidia devices, even though they are capable of performing
DMA up to 40 bits. On some architectures (such as arm64), system memory
is not guaranteed to be 32-bit addressable by PCI devices, and so this
change prevents NVidia devices from working on platforms such as AMD
Seattle.
Since the original commit already mentioned that up to 40 bits of DMA
is supported, and given that the code has been updated in the meantime
to support a 40 bit DMA mask on other devices, revert commit 49d9e77e72cf
and explicitly set the DMA mask to 40 bits for NVidia devices.
Fixes: 49d9e77e72cf ('ALSA: hda - Fix system panic when DMA > 40 bits...') Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 36b701fae12a ('netfilter: nf_tables: validate maximum value of u32 netlink attributes') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit f436b2ac90a0 ("arm64: kernel: fix architected PMU registers
unconditional access") made sure we wouldn't access unimplemented
PMU registers, but also left MDCR_EL2 uninitialized in that case,
leading to trap bits being potentially left set.
Make sure we always write something in that register.
Fixes: f436b2ac90a0 ("arm64: kernel: fix architected PMU registers unconditional access") Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This adds support to ftdi_sio for the Infineon TriBoard TC2X7
engineering board for first-generation Aurix SoCs with Tricore CPUs.
Mere addition of the device IDs does the job.
Signed-off-by: Stefan Tauner <stefan.tauner@technikum-wien.at> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Accesses to the rtsx usb device, which is the parent of the rtsx memstick
device, must not be done unless it's runtime resumed. This is currently not
the case and it could trigger various errors.
Fix this by properly deal with runtime PM in this regards. This means
making sure the device is runtime resumed, when serving requests via the
->request() callback or changing settings via the ->set_param() callbacks.
Cc: Ritesh Raj Sarraf <rrs@researchut.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Accesses to the rtsx usb device, which is the parent of the rtsx memstick
device, must not be done unless it's runtime resumed.
Therefore when the rtsx_usb_ms driver polls for inserted memstick cards,
let's add pm_runtime_get|put*() to make sure accesses is done when the
rtsx usb device is runtime resumed.
Accesses of the rtsx sdmmc's parent device, which is the rtsx usb device,
must be done when it's runtime resumed. Currently this isn't case when
changing the led, so let's fix this by adding a pm_runtime_get_sync() and
a pm_runtime_put() around those operations.
The rtsx_usb_sdmmc driver may bail out in its ->set_ios() callback when no
SD card is inserted. This is wrong, as it could cause the device to remain
runtime resumed when it's unused. Fix this behaviour.
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Potentially overflowing expression 1000000 * data->timeout_clks with
type unsigned int is evaluated using 32-bit arithmetic, and then used
in a context that expects an expression of type unsigned long long.
To avoid overflow, cast 1000000U to type unsigned long long.
Special thanks to Coverity.
Fixes: 7f05538af71c ("mmc: sdhci: fix data timeout (part 2)") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We accidentally overwrite the original saved value of "flags" so that we
can't re-enable IRQs at the end of the function. Presumably this
function is mostly called with IRQs disabled or it would be obvious in
testing.
Fixes: aceeffbb59bb ("zfcp: trace full payload of all SAN records (req,resp,iels)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The goal of the patch is to fix this scenario:
ip link add dummy1 type dummy
ip link set dummy1 up
ip link set lo down ; ip link set lo up
After that sequence, the local route to the link layer address of dummy1 is
not there anymore.
When the loopback is set down, all local routes are deleted by
addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still
exists, because the corresponding idev has a reference on it. After the rcu
grace period, dst_rcu_free() is called, and thus ___dst_free(), which will
set obsolete to DST_OBSOLETE_DEAD.
In this case, init_loopback() is called before dst_rcu_free(), thus
obsolete is still sets to something <= 0. So, the function doesn't add the
route again. To avoid that race, let's check the rt6 refcnt instead.
Fixes: 25fb6ca4ed9c ("net IPv6 : Fix broken IPv6 routing table after loopback down-up") Fixes: a881ae1f625c ("ipv6: don't call addrconf_dst_alloc again when enable lo") Fixes: 33d99113b110 ("ipv6: reallocate addrconf router for ipv6 address when lo device up") Reported-by: Francesco Santoro <francesco.santoro@6wind.com> Reported-by: Samuel Gauthier <samuel.gauthier@6wind.com> CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> CC: Sabrina Dubroca <sd@queasysnail.net> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> CC: Weilong Chen <chenweilong@huawei.com> CC: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In mac80211, multicast A-MSDUs are accepted in many cases that
they shouldn't be accepted in:
* drop A-MSDUs with a multicast A1 (RA), as required by the
spec in 9.11 (802.11-2012 version)
* drop A-MSDUs with a 4-addr header, since the fourth address
can't actually be useful for them; unless 4-address frame
format is actually requested, even though the fourth address
is still not useful in this case, but ignored
Accepting the first case, in particular, is very problematic
since it allows anyone else with possession of a GTK to send
unicast frames encapsulated in a multicast A-MSDU, even when
the AP has client isolation enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes one use-after-free report[1] by KASAN.
In __scsi_scan_target(), when a type 31 device is probed,
SCSI_SCAN_TARGET_PRESENT is returned and the target will be scanned
again.
Inside the following scsi_report_lun_scan(), one new scsi_device
instance is allocated, and scsi_probe_and_add_lun() is called again to
probe the target and still see type 31 device, finally
__scsi_remove_device() is called to remove & free the device at the end
of scsi_probe_and_add_lun(), so cause use-after-free in
scsi_report_lun_scan().
And the following SCSI log can be observed:
scsi 0:0:2:0: scsi scan: INQUIRY pass 1 length 36
scsi 0:0:2:0: scsi scan: INQUIRY successful with code 0x0
scsi 0:0:2:0: scsi scan: peripheral device type of 31, no device added
scsi 0:0:2:0: scsi scan: Sending REPORT LUNS to (try 0)
scsi 0:0:2:0: scsi scan: REPORT LUNS successful (try 0) result 0x0
scsi 0:0:2:0: scsi scan: REPORT LUN scan
scsi 0:0:2:0: scsi scan: INQUIRY pass 1 length 36
scsi 0:0:2:0: scsi scan: INQUIRY successful with code 0x0
scsi 0:0:2:0: scsi scan: peripheral device type of 31, no device added
BUG: KASAN: use-after-free in __scsi_scan_target+0xbf8/0xe40 at addr ffff88007b44a104
This patch fixes the issue by moving the putting reference at
the end of scsi_report_lun_scan().
Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Mismatching stream names in DAPM route and widget definitions are
causing compilation errors. Fixing these names allows the cs4270
driver to compile and function.
[Errors must be at probe time not compile time -- broonie]
Signed-off-by: Murray Foster <mrafoster@gmail.com> Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit f68381a70bb2 (mmc: block: fix packed command header endianness)
correctly fixed endianness handling of packed_cmd_hdr in
mmc_blk_packed_hdr_wrq_prep.
But now, sparse complains about incorrect types:
drivers/mmc/card/block.c:1613:27: sparse: incorrect type in assignment (different base types)
drivers/mmc/card/block.c:1613:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/mmc/card/block.c:1613:27: got restricted __le32 [usertype] <noident>
...
So annotate cmd_hdr properly using __le32 to make everyone happy.
Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than
frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which
drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering.
In this case thaw_super() will wrongly call s_op->unfreeze_fs() before
it was actually frozen, and call sb_freeze_unlock() which leads to the
unbalanced percpu_up_write(). Unfortunately lockdep can't detect this,
so this triggers misc BUG_ON()'s in kernel/rcu/sync.c.
Reported-and-tested-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cleanup some missing mem frees on some cifs ioctls, and
clarify others to make more obvious that no data is returned.
Signed-off-by: Steve French <smfrench@gmail.com> Acked-by: Sachin Prabhu <sprabhu@redhat.com>
[bwh: Backported to 3.16:
- Drop changes to smb2_duplicate_extents(), smb3_set_integrity()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[CIFS] We had cases where we sent a SMB2/SMB3 setinfo request with all
timestamp (and DOS attribute) fields marked as 0 (ie do not change)
e.g. on chmod or chown.
Signed-off-by: Steve French <steve.french@primarydata.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Remove the global file_list_lock to simplify cifs/smb3 locking and
have spinlocks that more closely match the information they are
protecting.
Add new tcon->open_file_lock and file->file_info_lock spinlocks.
Locks continue to follow a heirachy,
cifs_socket --> cifs_ses --> cifs_tcon --> cifs_file
where global tcp_ses_lock still protects socket and cifs_ses, while the
the newer locks protect the lower level structure's information
(tcon and cifs_file respectively).
Signed-off-by: Steve French <steve.french@primarydata.com> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Reviewed-by: Germano Percossi <germano.percossi@citrix.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
GUIDs although random, and 16 bytes, need to be generated as
proper uuids.
Signed-off-by: Steve French <steve.french@primarydata.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Reported-by: David Goebels <davidgoe@microsoft.com>
[bwh: Backported to 3.16: drop changes to create_durable_v2_buf()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Steve French <steve.french@primarydata.com> Reported-by: David Goebel <davidgoe@microsoft.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The kernel client requests 2 credits for many operations even though
they only use 1 credit (presumably to build up a buffer of credit).
Some servers seem to give the client as much credit as is requested. In
this case, the amount of credit the client has continues increasing to
the point where (server->credits * MAX_BUFFER_SIZE) overflows in
smb2_wait_mtu_credits().
Fix this by throttling the credit requests if an set limit is reached.
For async requests where the credit charge may be > 1, request as much
credit as what is charged.
The limit is chosen somewhat arbitrarily. The Windows client
defaults to 128 credits, the Windows server allows clients up to
512 credits (or 8192 for Windows 2016), and the NetApp server
(and at least one other) does not limit clients at all.
Choose a high enough value such that the client shouldn't limit
performance.
This behavior was seen with a NetApp filer (NetApp Release 9.0RC2).
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.16: drop changes to smb2_async_{read,write}v()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In debugging smb3, it is useful to display the number
of credits available, so we can see when the server has not granted
sufficient operations for the client to make progress, or alternatively
the client has requested too many credits (as we saw in a recent bug)
so we can compare with the number of credits the server thinks
we have.
Add a /proc/fs/cifs/DebugData line to display the client view
on how many credits are available.
Signed-off-by: Steve French <steve.french@primarydata.com> Reported-by: Germano Percossi <germano.percossi@citrix.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently regs_return_value always negates reg[2] if it determines
the syscall has failed, but when called in kernel context this check is
invalid and may result in returning a wrong value.
This fixes errors reported by CONFIG_KPROBES_SANITY_TEST
Fixes: d7e7528bcd45 ("Audit: push audit success and retcode into arch ptrace.h") Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14381/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 6d07b68ce16a ("ipc/sem.c: optimize sem_lock()") introduced a
race:
sem_lock has a fast path that allows parallel simple operations.
There are two reasons why a simple operation cannot run in parallel:
- a non-simple operations is ongoing (sma->sem_perm.lock held)
- a complex operation is sleeping (sma->complex_count != 0)
As both facts are stored independently, a thread can bypass the current
checks by sleeping in the right positions. See below for more details
(or kernel bugzilla 105651).
The patch fixes that by creating one variable (complex_mode)
that tracks both reasons why parallel operations are not possible.
The patch also updates stale documentation regarding the locking.
With regards to stable kernels:
The patch is required for all kernels that include the
commit 6d07b68ce16a ("ipc/sem.c: optimize sem_lock()") (3.10?)
The alternative is to revert the patch that introduced the race.
The patch is safe for backporting, i.e. it makes no assumptions
about memory barriers in spin_unlock_wait().
Background:
Here is the race of the current implementation:
Thread A: (simple op)
- does the first "sma->complex_count == 0" test
Thread B: (complex op)
- does sem_lock(): This includes an array scan. But the scan can't
find Thread A, because Thread A does not own sem->lock yet.
- the thread does the operation, increases complex_count,
drops sem_lock, sleeps
Thread A:
- spin_lock(&sem->lock), spin_is_locked(sma->sem_perm.lock)
- sleeps before the complex_count test
Thread C: (complex op)
- does sem_lock (no array scan, complex_count==1)
- wakes up Thread B.
- decrements complex_count
Thread A:
- does the complex_count test
Bug:
Now both thread A and thread C operate on the same array, without
any synchronization.
Fixes: 6d07b68ce16a ("ipc/sem.c: optimize sem_lock()") Link: http://lkml.kernel.org/r/1469123695-5661-1-git-send-email-manfred@colorfullife.com Reported-by: <felixh@informatik.uni-bremen.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: <1vier1@web.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16:
- We missed out on some earlier memory barrier changes
- Use set_mb instead of smp_store_mb] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
CPUs without single-byte and double-byte loads and stores place some
"interesting" requirements on concurrent code. For example (adapted
from Peter Hurley's test code), suppose we have the following structure:
Of course, it is common (and good) practice to place data protected
by different locks in separate cache lines. However, if the locks are
rarely acquired (for example, only in rare error cases), and there are
a great many instances of the data structure, then memory footprint can
trump false-sharing concerns, so that it can be better to place them in
the same cache cache line as above.
But if the CPU does not support single-byte loads and stores, a store
to foop->a will do a non-atomic read-modify-write operation on foop->b,
which will come as a nasty surprise to someone holding foop->lock2. So we
now require CPUs to support single-byte and double-byte loads and stores.
Therefore, this commit adjusts the definition of __native_word() to allow
these sizes to be used by smp_load_acquire() and smp_store_release().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Daniel Walker reported problems which happens when
crash_kexec_post_notifiers kernel option is enabled
(https://lkml.org/lkml/2015/6/24/44).
In that case, smp_send_stop() is called before entering kdump routines
which assume other CPUs are still online. As the result, kdump
routines fail to save other CPUs' registers. Additionally for MIPS
OCTEON, it misses to stop the watchdog timer.
To fix this problem, call a new kdump friendly function,
crash_smp_send_stop(), instead of the smp_send_stop() when
crash_kexec_post_notifiers is enabled. crash_smp_send_stop() is a
weak function, and it just call smp_send_stop(). Architecture
codes should override it so that kdump can work appropriately.
This patch provides MIPS version.
Fixes: f06e5153f4ae (kernel/panic.c: add "crash_kexec_post_notifiers" option) Link: http://lkml.kernel.org/r/20160810080950.11028.28000.stgit@sysi4-13.yrl.intra.hitachi.co.jp Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Reported-by: Daniel Walker <dwalker@fifo99.com> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Xunlei Pang <xpang@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Toshi Kani <toshi.kani@hpe.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: David Daney <david.daney@cavium.com> Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: "Steven J. Hill" <steven.hill@cavium.com> Cc: Corey Minyard <cminyard@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Daniel Walker reported problems which happens when
crash_kexec_post_notifiers kernel option is enabled
(https://lkml.org/lkml/2015/6/24/44).
In that case, smp_send_stop() is called before entering kdump routines
which assume other CPUs are still online. As the result, for x86, kdump
routines fail to save other CPUs' registers and disable virtualization
extensions.
To fix this problem, call a new kdump friendly function,
crash_smp_send_stop(), instead of the smp_send_stop() when
crash_kexec_post_notifiers is enabled. crash_smp_send_stop() is a weak
function, and it just call smp_send_stop(). Architecture codes should
override it so that kdump can work appropriately. This patch only
provides x86-specific version.
For Xen's PV kernel, just keep the current behavior.
NOTES:
- Right solution would be to place crash_smp_send_stop() before
__crash_kexec() invocation in all cases and remove smp_send_stop(), but
we can't do that until all architectures implement own
crash_smp_send_stop()
- crash_smp_send_stop()-like work is still needed by
machine_crash_shutdown() because crash_kexec() can be called without
entering panic()
Fixes: f06e5153f4ae (kernel/panic.c: add "crash_kexec_post_notifiers" option) Link: http://lkml.kernel.org/r/20160810080948.11028.15344.stgit@sysi4-13.yrl.intra.hitachi.co.jp Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Reported-by: Daniel Walker <dwalker@fifo99.com> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Xunlei Pang <xpang@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Toshi Kani <toshi.kani@hpe.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: David Daney <david.daney@cavium.com> Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: "Steven J. Hill" <steven.hill@cavium.com> Cc: Corey Minyard <cminyard@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Debugging a data corruption issue with virtio-net/vhost-net led to
the observation that __copy_tofrom_user was occasionally returning
a value 16 larger than it should. Since the return value from
__copy_tofrom_user is the number of bytes not copied, this means
that __copy_tofrom_user can occasionally return a value larger
than the number of bytes it was asked to copy. In turn this can
cause higher-level copy functions such as copy_page_to_iter_iovec
to corrupt memory by copying data into the wrong memory locations.
It turns out that the failing case involves a fault on the store
at label 79, and at that point the first unmodified byte of the
destination is at R3 + 16. Consequently the exception handler
for that store needs to add 16 to R3 before using it to work out
how many bytes were not copied, but in this one case it was not
adding the offset to R3. To fix it, this moves the label 179 to
the point where we add 16 to R3. I have checked manually all the
exception handlers for the loads and stores in this code and the
rest of them are correct (it would be excellent to have an
automated test of all the exception cases).
This bug has been present since this code was initially
committed in May 2002 to Linux version 2.5.20.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This commit fixes a stack corruption in the pseries specific code dealing
with the huge pages.
In __pSeries_lpar_hugepage_invalidate() the buffer used to pass arguments
to the hypervisor is not large enough. This leads to a stack corruption
where a previously saved register could be corrupted leading to unexpected
result in the caller, like the following panic:
Most of the time, the bug is surfacing in a caller up in the stack from
__pSeries_lpar_hugepage_invalidate() which is quite confusing.
This bug is pending since v3.11 but was hidden if a caller of the
caller of __pSeries_lpar_hugepage_invalidate() has pushed the corruped
register (r18 in this case) in the stack and is not using it until
restoring it. GCC 6.2.0 seems to raise it more frequently.
This commit also change the definition of the parameter buffer in
pSeries_lpar_flush_hash_range() to rely on the global define
PLPAR_HCALL9_BUFSIZE (no functional change here).
The filesystem used in this case is ubifs, but it can be triggered on
many other filesystems.
When preadv64() is called with offset=0xffffffff000, a page with
index=0xffffffff will be added to the radix tree of ->mapping. Then
this page can be found in ->mapping with pagevec_lookup(). After that,
truncate_inode_pages_range(), which is called in ftruncate(), will fall
into an infinite loop:
- find a page with index=0xffffffff, since index>=end, this page won't
be truncated
- index++, and index become 0
- the page with index=0xffffffff will be found again
The data type of index is unsigned long, so index won't overflow to 0 on
64 bits architecture in this case, and the dead loop won't happen.
Since truncate_inode_pages_range() is executed with holding lock of
inode->i_rwsem, any operation related with this lock will be blocked,
and a hung task will happen, e.g.:
INFO: task truncate_test:3364 blocked for more than 120 seconds.
...
call_rwsem_down_write_failed+0x17/0x30
generic_file_write_iter+0x32/0x1c0
ubifs_write_iter+0xcc/0x170
__vfs_write+0xc4/0x120
vfs_write+0xb2/0x1b0
SyS_write+0x46/0xa0
The page with index=0xffffffff added to ->mapping is useless. Fix this
by checking the read position before allocating pages.
Link: http://lkml.kernel.org/r/1475151010-40166-1-git-send-email-fangwei1@huawei.com Signed-off-by: Wei Fang <fangwei1@huawei.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / thirdparty / kernel / stable.git / log
