This patch tries to fix a PEBS warning found in my stress test. The
following perf command can easily trigger the pebs warning or spurious
NMI error on Skylake/Broadwell/Haswell platforms:
sudo perf record -e 'cpu/umask=0x04,event=0xc4/pp,cycles,branches,ref-cycles,cache-misses,cache-references' --call-graph fp -b -c1000 -a
Also the NMI watchdog must be enabled.
For this case, the events number is larger than counter number. So
perf has to do multiplexing.
In perf_mux_hrtimer_handler, it does perf_pmu_disable(), schedule out
old events, rotate_ctx, schedule in new events and finally
perf_pmu_enable().
If the old events include precise event, the MSR_IA32_PEBS_ENABLE
should be cleared when perf_pmu_disable(). The MSR_IA32_PEBS_ENABLE
should keep 0 until the perf_pmu_enable() is called and the new event is
precise event.
However, there is a corner case which could restore PEBS_ENABLE to
stale value during the above period. In perf_pmu_disable(), GLOBAL_CTRL
will be set to 0 to stop overflow and followed PMI. But there may be
pending PMI from an earlier overflow, which cannot be stopped. So even
GLOBAL_CTRL is cleared, the kernel still be possible to get PMI. At
the end of the PMI handler, __intel_pmu_enable_all() will be called,
which will restore the stale values if old events haven't scheduled
out.
Once the stale pebs value is set, it's impossible to be corrected if
the new events are non-precise. Because the pebs_enabled will be set
to 0. x86_pmu.enable_all() will ignore the MSR_IA32_PEBS_ENABLE
setting. As a result, the following NMI with stale PEBS_ENABLE
trigger pebs warning.
The pending PMI after enabled=0 will become harmless if the NMI handler
does not change the state. This patch checks cpuc->enabled in pmi and
only restore the state when PMU is active.
The error path in perf_event_open() is such that asking for a sampling
event on a PMU that doesn't generate interrupts will end up in dropping
the perf_sched_count even though it hasn't been incremented for this
event yet.
Given a sufficient amount of these calls, we'll end up disabling
scheduler's jump label even though we'd still have active events in the
system, thereby facilitating the arrival of the infernal regions upon us.
I'm fixing this by moving account_event() inside perf_event_alloc().
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: vince@deater.net Link: http://lkml.kernel.org/r/1456917854-29427-1-git-send-email-alexander.shishkin@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add USB ID 0411:01fd for Buffalo WLI-UC-G450 wireless adapter,
RT chipset 3593
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch corrects the error case in association path by returning
-1. Earlier "media_connected" used to remain on in this error case
causing failure for further association attempts.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Fixes: b887664d882ee4 ('mwifiex: channel switch handling for station') Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The IPVS SIP persistence engine is not able to parse the SIP header
"Call-ID" when such header is inserted in the first positions of
the SIP message.
When IPVS is configured with "--pe sip" option, like for example:
ipvsadm -A -u 1.2.3.4:5060 -s rr --pe sip -p 120 -o
some particular messages (see below for details) do not create entries
in the connection template table, which can be listed with:
ipvsadm -Lcn --persistent-conn
Problematic SIP messages are SIP responses having "Call-ID" header
positioned just after message first line:
SIP/2.0 200 OK
[Call-ID header here]
[rest of the headers]
When "Call-ID" header is positioned down (after a few other headers)
it is correctly recognized.
This is due to the data offset used in get_callid function call inside
ip_vs_pe_sip.c file: since dptr already points to the start of the
SIP message, the value of dataoff should be initially 0.
Otherwise the header is searched starting from some bytes after the
first character of the SIP message.
Fixes: 758ff0338722 ("IPVS: sip persistence engine") Signed-off-by: Marco Angaroni <marcoangaroni@gmail.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On CPU hotplug the steal time accounting can keep a stale rq->prev_steal_time
value over CPU down and up. So after the CPU comes up again the delta
calculation in steal_account_process_tick() wreckages itself due to the
unsigned math:
So if steal is smaller than rq->prev_steal_time we end up with an insane large
value which then gets added to rq->prev_steal_time, resulting in a permanent
wreckage of the accounting. As a consequence the per CPU stats in /proc/stat
become stale.
Nice trick to tell the world how idle the system is (100%) while the CPU is
100% busy running tasks. Though we prefer realistic numbers.
None of the accounting values which use a previous value to account for
fractions is reset at CPU hotplug time. update_rq_clock_task() has a sanity
check for prev_irq_time and prev_steal_time_rq, but that sanity check solely
deals with clock warps and limits the /proc/stat visible wreckage. The
prev_time values are still wrong.
Solution is simple: Reset rq->prev_*_time when the CPU is plugged in again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rik van Riel <riel@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Glauber Costa <glommer@parallels.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: commit 095c0aa83e52 "sched: adjust scheduler cpu power for stolen time" Fixes: commit aa483808516c "sched: Remove irq time from available CPU power" Fixes: commit e6e6685accfa "KVM guest: Steal time accounting" Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1603041539490.3686@nanos Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Discard policy uses ack_notifiers to prevent injection of PIT interrupts
before EOI from the last one.
This patch changes the policy to always try to deliver the interrupt,
which makes a difference when its vector is in ISR.
Old implementation would drop the interrupt, but proposed one injects to
IRR, like real hardware would.
The old policy breaks legacy NMI watchdogs, where PIT is used through
virtual wire (LVT0): PIT never sends an interrupt before receiving EOI,
thus a guest deadlock with disabled interrupts will stop NMIs.
Note that NMI doesn't do EOI, so PIT also had to send a normal interrupt
through IOAPIC. (KVM's PIT is deeply rotten and luckily not used much
in modern systems.)
Even though there is a chance of regressions, I think we can fix the
LVT0 NMI bug without introducing a new tick policy.
Reported-by: Yuki Shibuya <shibuya.yk@ncos.nec.co.jp> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
early_init_dt_alloc_reserved_memory_arch passes end as 0 to
__memblock_alloc_base, when limits are not specified. But
__memblock_alloc_base takes end value of 0 as MEMBLOCK_ALLOC_ACCESSIBLE
and limits the end to memblock.current_limit. This results in regions
never being placed in HIGHMEM area, for e.g. CMA.
Let __memblock_alloc_base allocate from anywhere in memory if limits are
not specified.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the initial fix for non-zero divider shift value, the parenthesis
was missing after the negate operation. This patch adds the required
parenthesis. Otherwise, lower bits may be cleared unintentionally.
Signed-off-by: Loc Ho <lho@apm.com> Acked-by: Toan Le <toanle@apm.com> Fixes: 1382ea631ddd ("clk: xgene: Fix divider with non-zero shift value") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Remove setting and clearing MTIP_PF_EH_ACTIVE_BIT flag in
mtip_handle_tfe() as they are redundant. Also avoid waking
up service thread from mtip_handle_tfe() because it is
already woken up in case of taskfile error.
Signed-off-by: Selvan Mani <smani@micron.com> Signed-off-by: Rajesh Kumar Sambandam <rsambandam@micron.com> Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com> Signed-off-by: Jens Axboe <axboe@fb.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The command timeout is terribly long, whole two hours. Make it 60s so if
things do go wrong, the user gets feedback in relatively short time, so
they can take corrective actions and/or investigate using tools and such.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A number of spots in the xdr decoding follow a pattern like
n = be32_to_cpup(p++);
READ_BUF(n + 4);
where n is a u32. The only bounds checking is done in READ_BUF itself,
but since it's checking (n + 4), it won't catch cases where n is very
large, (u32)(-4) or higher. I'm not sure exactly what the consequences
are, but we've seen crashes soon after.
Instead, just break these up into two READ_BUF()s.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Calling return copy_to_user(...) in an ioctl will not do the right thing
if there's a pagefault: copy_to_user returns the number of bytes not
copied in this case.
Fix up watchdog/rc32434_wdt to do
return copy_to_user(...)) ? -EFAULT : 0;
instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On my bttv card "Hauppauge WinTV [card=10]" capturing in YV12 fmt at max
size results in a solid green rectangle being captured (all colors 0 in
YUV).
This turns out to be caused by max-width (924) not being a multiple of 16.
We've likely never hit this problem before since normally xawtv / tvtime,
etc. will prefer packed pixel formats. But when using a video card which
is using xf86-video-modesetting + glamor, only planar XVideo fmts are
available, and xawtv will chose a matching capture format to avoid needing
to do conversion, triggering the solid green window problem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Let the target core check task existence instead of the SRP target
driver. Additionally, let the target core check the validity of the
task management request instead of the ib_srpt driver.
Commit 028cd86b794f4a ("video: da8xx-fb: fix the polarities of the
hsync/vsync pulse") fixes polarities of HSYNC/VSYNC pulse but
forgot to update known_lcd_panels[] which had sync values
according to old logic. This breaks LCD at least on DA850 EVM.
This patch fixes this issue and I have tested this for panel
"Sharp_LK043T1DG01" using DA850 EVM board.
Fixes: 028cd86b794f4a ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse") Signed-off-by: Sushaanth Srirangapathi <sushaanth.s@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The calculation for the timeout based on the number of card clocks is
incorrect. The calculation assumed:
timeout in microseconds = clock cycles / clock in Hz
which is clearly a several orders of magnitude wrong. Fix this by
multiplying the clock cycles by 1000000 prior to dividing by the Hz
based clock. Also, as per part 1, ensure that the division rounds
up.
As this needs 64-bit math via do_div(), avoid it if the clock cycles
is zero.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The data timeout gives the minimum amount of time that should be
waited before timing out if no data is received from the card.
Simply dividing the nanosecond part by 1000 does not give this
required guarantee, since such a division rounds down. Use
DIV_ROUND_UP() to give the desired timeout.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since a crypto_ahash_import() can be called against a request context
that has not had a crypto_ahash_init() performed, the request context
needs to be cleared to insure there is no random data present. If not,
the random data can result in a kernel oops during crypto_ahash_update().
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
mkspec is copying built kernel to temporrary location
/boot/vmlinuz-$KERNELRELEASE-rpm
and runs installkernel on it. This however directly leads to grub2
menuentry for this suffixed binary being generated as well during the run
of installkernel script.
Later in the process the temporary -rpm suffixed files are removed, and
therefore we end up with spurious (and non-functional) grub2 menu entries
for each installed kernel RPM.
Fix that by using a different temporary name (prefixed by '.'), so that
the binary is not recognized as an actual kernel binary and no menuentry
is created for it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Fixes: 3c9c7a14b627 ("rpm-pkg: add %post section to create initramfs and grub hooks") Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
'max_discard_sectors' is in sectors, while 'stripe' is in bytes.
This fixes the problem where DISCARD would get disabled on some larger
RAID5 configurations (6 or more drives in my testing), while it worked
as expected with smaller configurations.
Fixes: 620125f2bf8 ("MD: raid5 trim support") Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Despite care take to allocate clocks state containers the
SP810 driver actually just supports creating one instance:
all clocks registered for every instance will end up with the
exact same name and __clk_init() will fail.
Rename the timclken<0> .. timclken<n> to sp810_<instance>_<n>
so every clock on every instance gets a unique name.
This is necessary for the RealView PBA8 which has two SP810
blocks: the second block will not register its clocks unless
every clock on every instance is unique and results in boot
logs like this:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../drivers/clk/versatile/clk-sp810.c:137
clk_sp810_of_setup+0x110/0x154()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.5.0-rc2-00030-g352718fc39f6-dirty #225
Hardware name: ARM RealView Machine (Device Tree Support)
[<c00167f8>] (unwind_backtrace) from [<c0013204>]
(show_stack+0x10/0x14)
[<c0013204>] (show_stack) from [<c01a049c>]
(dump_stack+0x84/0x9c)
[<c01a049c>] (dump_stack) from [<c0024990>]
(warn_slowpath_common+0x74/0xb0)
[<c0024990>] (warn_slowpath_common) from [<c0024a68>]
(warn_slowpath_null+0x1c/0x24)
[<c0024a68>] (warn_slowpath_null) from [<c051eb44>]
(clk_sp810_of_setup+0x110/0x154)
[<c051eb44>] (clk_sp810_of_setup) from [<c051e3a4>]
(of_clk_init+0x12c/0x1c8)
[<c051e3a4>] (of_clk_init) from [<c0504714>]
(time_init+0x20/0x2c)
[<c0504714>] (time_init) from [<c0501b18>]
(start_kernel+0x244/0x3c4)
[<c0501b18>] (start_kernel) from [<7000807c>] (0x7000807c)
---[ end trace cb88537fdc8fa200 ]---
Cc: Michael Turquette <mturquette@baylibre.com> Cc: Pawel Moll <pawel.moll@arm.com> Fixes: 6e973d2c4385 "clk: vexpress: Add separate SP810 driver" Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The PCI config header (first 64 bytes of each device's config space) is
defined by the PCI spec so generic software can identify the device and
manage its usage of I/O, memory, and IRQ resources.
Some non-spec-compliant devices put registers other than BARs where the
BARs should be. When the PCI core sizes these "BARs", the reads and writes
it does may have unwanted side effects, and the "BAR" may appear to
describe non-sensical address space.
Add a flag bit to mark non-compliant devices so we don't touch their BARs.
Turn off IO/MEM decoding to prevent the devices from consuming address
space, since we can't read the BARs to find out what that address space
would be.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Andi Kleen <ak@linux.intel.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 5942ddbc500d ("mtd: introduce mtd_block_markbad interface")
incorrectly changed onenand_block_markbad() to call mtd_block_markbad
instead of onenand_chip's block_markbad function. As a result the function
will now recurse and deadlock. Fix by reverting the change.
Fixes: 5942ddbc500d ("mtd: introduce mtd_block_markbad interface") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When CONFIG_OPTIMIZE_INLINING is set, the sta_info_insert_finish
function consumes more stack than normally, exceeding the
1024 byte limit on ARM:
net/mac80211/sta_info.c: In function 'sta_info_insert_finish':
net/mac80211/sta_info.c:561:1: error: the frame size of 1080 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two functions that put a 'struct station_info'
on the stack: __sta_info_destroy_part2 and sta_info_insert_finish, and
this structure alone requires up to 792 bytes.
Hoping that both are called rarely enough, this replaces the
on-stack structure with a dynamic allocation, which unfortunately
requires some suboptimal error handling for out-of-memory.
The __sta_info_destroy_part2 function is actually affected by the
stack usage twice because it calls cfg80211_del_sta_sinfo(), which
has another instance of struct station_info on its stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 98b6218388e3 ("mac80211/cfg80211: add station events") Fixes: 6f7a8d26e266 ("mac80211: send statistics with delete station event") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.16: there's only one instance to fix] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.
This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().
On ath10k it was possible to hit this problem in
the following case:
1. wlan0 uses queue 0
(ath10k maps queues per vif)
2. offchannel uses queue 15
3. queues 1-14 are unused
4. ieee80211_stop_queues()
5. ieee80211_wake_queue(q=0)
6. ieee80211_wake_queue(q=15)
(other queues are not woken up because both
driver and mac80211 know other queues are
unused)
7. ieee80211_rx_h_mesh_fwding()
8. ieee80211_select_queue_80211() returns 2
9. ieee80211_queue_stopped(q=2) returns true
10. frame is dropped (oops!)
Fixes: d3c1597b8d1b ("mac80211: fix forwarded mesh frame queue mapping") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
aac_fib_map_free() calls pci_free_consistent() without checking that
dev->hw_fib_va is not NULL and dev->max_fib_size is not zero.If they are
indeed NULL/0, this will result in a hang as pci_free_consistent() will
attempt to invalidate cache for the entire 64-bit address space
(which would take a very long time).
Fixed by adding a check to make sure that dev->hw_fib_va and
dev->max_fib_size are not NULL and 0 respectively.
Fixes: 9ad5204d6 - "[SCSI]aacraid: incorrect dma mapping mask during blinked recover or user initiated reset" Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When an error happens during alias parsing currently the complete
parsing of all attributes of the PMU is stopped. This is breaks old perf
on a newer kernel that may have not-yet-know alias attributes (such as
.scale or .per-pkg).
Continue when some attribute is unparseable.
This is IMHO a stable candidate and should be backported to older
versions to avoid problems with newer kernels.
v2: Print warnings when something goes wrong.
v3: Change warning to debug output
Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Link: http://lkml.kernel.org/r/1455749095-18358-1-git-send-email-andi@firstfloor.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
buf_idx type was changed to size_t, and few places
missed out to change the print format from %ld to %zu.
Use also uz for buf.size which is also of size_t
Fixes:
commit 56988f22e097 ("mei: fix possible integer overflow issue")'
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There is a possible integer overflow following by a buffer overflow
when accumulating messages coming from the FW to compose a full payload.
Occurrence of wrap around has to be prevented for next message size
calculation.
For unsigned integer the addition overflow has occurred when the
result is smaller than one of the arguments.
To simplify the fix, the types of buf.size and buf_idx are set to the
same width, namely size_t also to be aligned with the type of length
parameter in file read/write ops.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- Adjust context, indentation
- Return error directly, rather than through cb->status and the completion list
- Fix up additional format string in mei_cl_write()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Based on CPU type choose generic omap3 or omap3430 specific cpuidle
parameters. Parameters for omap3430 were measured on Nokia N900 device and
added by commit 5a1b1d3a9efa ("OMAP3: RX-51: Pass cpu idle parameters")
which were later removed by commit 231900afba52 ("ARM: OMAP3: cpuidle -
remove rx51 cpuidle parameters table") due to huge code complexity.
This patch brings cpuidle parameters for omap3430 devices again, but uses
simple condition based on CPU type.
Fixes: 231900afba52 ("ARM: OMAP3: cpuidle - remove rx51 cpuidle
parameters table") Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present.
The adv7511 however still reported the EDID present after disconnecting
the HDMI cable. Fix the logic regarding this control. And when the EDID
is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver.
This was also missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
& is no longer allowed in column 0, since Coccinelle 1.0.4.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Tested-by: Nishanth Menon <nm@ti.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The davinci platform has tried to get support for the EEPROM right,
but failed to get a clean build so far. At the moment, we get
a warning whenever CONFIG_SYSFS is disabled, as that is needed by
EEPROM_AT24:
warning: (MACH_DAVINCI_EVM && MACH_SFFSDR && MACH_DAVINCI_DM6467_EVM && MACH_DAVINCI_DM365_EVM && MACH_DAVINCI_DA830_EVM && MACH_MITYOMAPL138 && MACH_MINI2440) selects EEPROM_AT24 which has unmet direct dependencies (I2C && SYSFS)
Kevin Hilman initially added the 'select' to ensure that EEPROM_AT24
is always enabled in machines that really want it for normal operation
(i.e. for reading the MAC address). This broke when I2C was disabled,
and Russell King followed up with another patch to select that as
well.
I now see that the SYSFS dependency is still missing, which leaves
us with three options:
a) add 'select SYSFS' in addition to the others
b) change AT24_EEPPROM to work without sysfs (should be possible)
c) remove all those selects again and get the files to build when
I2C is disabled.
I would really hate to do a) because adding select statements that
hardwire user-selectable symbols is generally a bad idea. I first
tried b) but then ended up redoing the patch from scratch to approach
c), so we can also remove the other selects.
I checked that CONFIG_I2C is still enabled with davinci_all_defconfig,
so that does not have to change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 45b146d746ea ("ARM: Davinci: Fix I2C build errors") Fixes: 22ca466847ad ("davinci: kconfig: select at24 eeprom for selected boards") Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:
drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.
In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 9c4c60554acf ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap") Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
hid_ignore_special_drivers works fine until hid_scan_report autodetects and
reassign devices (for hid-multitouch, hid-microsoft and hid-rmi).
Simplify the handling of the parameter: if it is there, use hid-generic, no
matter what, and if not, scan the device or rely on the hid_have_special_driver
table.
This was detected while trying to disable hid-multitouch on a Surface Pro cover
which prevented to use the keyboard.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This allows the transport layer (I have in mind hid-logitech-dj and uhid)
to set the group before it is added to the hid bus. This way, it can
bypass the hid_scan_report() call, and choose in advance which driver
will handle the newly created hid device.
Signed-off-by: Benjamin Tisssoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The patch that added Logitech Dual Action gamepad support forgot to
update the special driver list for the device. This caused the logitech
driver not to probe unless kernel module load order was favorable.
Update the special driver list to fix it. Thanks to Simon Wood for the
idea.
Cc: Vitaly Katraew <zawullon@gmail.com> Fixes: 56d0c8b7c8fb ("HID: add support for Logitech Dual Action gamepads") Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some devices I got show an inability to operate right after
power on if they are already connected. They are beyond recovery
if the descriptors are requested multiple times. So in case of
a timeout we rather bail early and reset again. But it must be
done only on the first loop lest we get into a reset/time out
spiral that can be overcome with a retry.
This patch is a rework of a patch that fell through the cracks.
http://www.spinics.net/lists/linux-usb/msg103263.html
Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As of commit 876fe76d793d03077eb61ba3afab4a383f46c554
"mtd: maps: physmap: Add reference counter to set_vpp()"
the comment in the header file is incorrect and misleading.
Fix it up.
Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Parsons <lost.distance@yahoo.com> Fixes: 876fe76d793d ("mtd: maps: physmap: Add reference counter to set_vpp()") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which
requires the PHY speed to be set in the LP_PHY_CTL register for SATA
hotplug to work.
Therefore, this commit updates the compatible string used to describe
the SATA IP in Armada 375 from marvell,orion-sata to
marvell,armada-370-sata.
Fixes: 4de59085091f753d08c8429d756b46756ab94665 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC") Signed-off-by: Lior Amsalem <alior@marvell.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 985087dbcb02 'misc: add support for bmp18x chips to the bmp085
driver' changed the BMP085 config symbol to a boolean. I see no
reason why the shared code cannot be built as a module, so change it
back to tristate.
Fixes: 985087dbcb02 ("misc: add support for bmp18x chips to the bmp085 driver") Cc: Eric Andersson <eric.andersson@unixphere.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The N_IRDA line discipline may access the previous line discipline's closed
and already-fre private data on open [1].
The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).
[1]
==================================================================
BUG: KASAN: use-after-free in irtty_open+0x422/0x550 at addr ffff8800331dd068
Read of size 4 by task a.out/13960
=============================================================================
BUG kmalloc-512 (Tainted: G B ): kasan: bad access detected
-----------------------------------------------------------------------------
...
Call Trace:
[<ffffffff815fa2ae>] __asan_report_load4_noabort+0x3e/0x40 mm/kasan/report.c:279
[<ffffffff836938a2>] irtty_open+0x422/0x550 drivers/net/irda/irtty-sir.c:436
[<ffffffff829f1b80>] tty_ldisc_open.isra.2+0x60/0xa0 drivers/tty/tty_ldisc.c:447
[<ffffffff829f21c0>] tty_set_ldisc+0x1a0/0x940 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff829da49e>] tty_ioctl+0xace/0x1fd0 drivers/tty/tty_io.c:2883
[< inline >] vfs_ioctl fs/ioctl.c:43
[<ffffffff816708ac>] do_vfs_ioctl+0x57c/0xe60 fs/ioctl.c:607
[< inline >] SYSC_ioctl fs/ioctl.c:622
[<ffffffff81671204>] SyS_ioctl+0x74/0x80 fs/ioctl.c:613
[<ffffffff852a7876>] entry_SYSCALL_64_fastpath+0x16/0x7a
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some UART HW has a single register combining UART_DLL/UART_DLM
(this was probably forgotten in the change that introduced the
callbacks, commit b32b19b8ffc05cbd3bf91c65e205f6a912ca15d9)
Fixes: b32b19b8ffc0 ("[SERIAL] 8250: set divisor register correctly ...") Signed-off-by: Sebastian Frias <sf84@laposte.net> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Use a local variable for the exported and imported state so that
alignment is not an issue. On export, set a local variable from the
request context and then memcpy the contents of the local variable to
the export memory area. On import, memcpy the import memory area into
a local variable and then use the local variable to set the request
context.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Steam frequently puts game binaries in folders with spaces.
Note: "(deleted)" markers are now treated as part of the file name.
Signed-off-by: Marcin Ślusarz <marcin.slusarz@gmail.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Fixes: 6064803313ba ("perf tools: Use sscanf for parsing /proc/pid/maps") Link: http://lkml.kernel.org/r/20160119190303.GA17579@marcin-Inspiron-7720 Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make the "Attempted send on closed socket" error messages generated in
nbd_request_handler() ratelimited.
When the nbd socket is shutdown, the nbd_request_handler() function emits
an error message for every request remaining in its queue. If the queue
is large, this will spam a large amount of messages to the log. There's
no need for a separate error message for each request, so this patch
ratelimits it.
In the specific case this was found, the system was virtual and the error
messages were logged to the serial port, which overwhelmed it.
Fixes: 4d48a542b427 ("nbd: fix I/O hang on disconnected nbds") Signed-off-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If struct xc2028_config is passed without a firmware name,
the following trouble may happen:
[11009.907205] xc2028 5-0061: type set to XCeive xc2028/xc3028 tuner
[11009.907491] ==================================================================
[11009.907750] BUG: KASAN: use-after-free in strcmp+0x96/0xb0 at addr ffff8803bd78ab40
[11009.907992] Read of size 1 by task modprobe/28992
[11009.907994] =============================================================================
[11009.907997] BUG kmalloc-16 (Tainted: G W ): kasan: bad access detected
[11009.907999] -----------------------------------------------------------------------------
[11009.908130] Bytes b4 ffff8803bd78ab30: 01 00 00 00 2a 07 00 00 9d 28 00 00 01 00 00 00 ....*....(......
[11009.908133] Object ffff8803bd78ab40: 01 00 00 00 00 00 00 00 b0 1d c3 6a 00 88 ff ff ...........j....
[11009.908137] CPU: 3 PID: 28992 Comm: modprobe Tainted: G B W 4.5.0-rc1+ #43
[11009.908140] Hardware name: /NUC5i7RYB, BIOS RYBDWi35.86A.0350.2015.0812.1722 08/12/2015
[11009.908142] ffff8803bd78a000ffff8802c273f1b8ffffffff81932007ffff8803c6407a80
[11009.908148] ffff8802c273f1e8ffffffff81556759ffff8803c6407a80ffffea000ef5e280
[11009.908153] ffff8803bd78ab40dffffc0000000000ffff8802c273f210ffffffff8155ccb4
[11009.908158] Call Trace:
[11009.908162] [<ffffffff81932007>] dump_stack+0x4b/0x64
[11009.908165] [<ffffffff81556759>] print_trailer+0xf9/0x150
[11009.908168] [<ffffffff8155ccb4>] object_err+0x34/0x40
[11009.908171] [<ffffffff8155f260>] kasan_report_error+0x230/0x550
[11009.908175] [<ffffffff81237d71>] ? trace_hardirqs_off_caller+0x21/0x290
[11009.908179] [<ffffffff8155e926>] ? kasan_unpoison_shadow+0x36/0x50
[11009.908182] [<ffffffff8155f5c3>] __asan_report_load1_noabort+0x43/0x50
[11009.908185] [<ffffffff8155ea00>] ? __asan_register_globals+0x50/0xa0
[11009.908189] [<ffffffff8194cea6>] ? strcmp+0x96/0xb0
[11009.908192] [<ffffffff8194cea6>] strcmp+0x96/0xb0
[11009.908196] [<ffffffffa13ba4ac>] xc2028_set_config+0x15c/0x630 [tuner_xc2028]
[11009.908200] [<ffffffffa13bac90>] xc2028_attach+0x310/0x8a0 [tuner_xc2028]
[11009.908203] [<ffffffff8155ea78>] ? memset+0x28/0x30
[11009.908206] [<ffffffffa13ba980>] ? xc2028_set_config+0x630/0x630 [tuner_xc2028]
[11009.908211] [<ffffffffa157a59a>] em28xx_attach_xc3028.constprop.7+0x1f9/0x30d [em28xx_dvb]
[11009.908215] [<ffffffffa157aa2a>] ? em28xx_dvb_init.part.3+0x37c/0x5cf4 [em28xx_dvb]
[11009.908219] [<ffffffffa157a3a1>] ? hauppauge_hvr930c_init+0x487/0x487 [em28xx_dvb]
[11009.908222] [<ffffffffa01795ac>] ? lgdt330x_attach+0x1cc/0x370 [lgdt330x]
[11009.908226] [<ffffffffa01793e0>] ? i2c_read_demod_bytes.isra.2+0x210/0x210 [lgdt330x]
[11009.908230] [<ffffffff812e87d0>] ? ref_module.part.15+0x10/0x10
[11009.908233] [<ffffffff812e56e0>] ? module_assert_mutex_or_preempt+0x80/0x80
[11009.908238] [<ffffffffa157af92>] em28xx_dvb_init.part.3+0x8e4/0x5cf4 [em28xx_dvb]
[11009.908242] [<ffffffffa157a6ae>] ? em28xx_attach_xc3028.constprop.7+0x30d/0x30d [em28xx_dvb]
[11009.908245] [<ffffffff8195222d>] ? string+0x14d/0x1f0
[11009.908249] [<ffffffff8195381f>] ? symbol_string+0xff/0x1a0
[11009.908253] [<ffffffff81953720>] ? uuid_string+0x6f0/0x6f0
[11009.908257] [<ffffffff811a775e>] ? __kernel_text_address+0x7e/0xa0
[11009.908260] [<ffffffff8104b02f>] ? print_context_stack+0x7f/0xf0
[11009.908264] [<ffffffff812e9846>] ? __module_address+0xb6/0x360
[11009.908268] [<ffffffff8137fdc9>] ? is_ftrace_trampoline+0x99/0xe0
[11009.908271] [<ffffffff811a775e>] ? __kernel_text_address+0x7e/0xa0
[11009.908275] [<ffffffff81240a70>] ? debug_check_no_locks_freed+0x290/0x290
[11009.908278] [<ffffffff8104a24b>] ? dump_trace+0x11b/0x300
[11009.908282] [<ffffffffa13e8143>] ? em28xx_register_extension+0x23/0x190 [em28xx]
[11009.908285] [<ffffffff81237d71>] ? trace_hardirqs_off_caller+0x21/0x290
[11009.908289] [<ffffffff8123ff56>] ? trace_hardirqs_on_caller+0x16/0x590
[11009.908292] [<ffffffff812404dd>] ? trace_hardirqs_on+0xd/0x10
[11009.908296] [<ffffffffa13e8143>] ? em28xx_register_extension+0x23/0x190 [em28xx]
[11009.908299] [<ffffffff822dcbb0>] ? mutex_trylock+0x400/0x400
[11009.908302] [<ffffffff810021a1>] ? do_one_initcall+0x131/0x300
[11009.908306] [<ffffffff81296dc7>] ? call_rcu_sched+0x17/0x20
[11009.908309] [<ffffffff8159e708>] ? put_object+0x48/0x70
[11009.908314] [<ffffffffa1579f11>] em28xx_dvb_init+0x81/0x8a [em28xx_dvb]
[11009.908317] [<ffffffffa13e81f9>] em28xx_register_extension+0xd9/0x190 [em28xx]
[11009.908320] [<ffffffffa0150000>] ? 0xffffffffa0150000
[11009.908324] [<ffffffffa0150010>] em28xx_dvb_register+0x10/0x1000 [em28xx_dvb]
[11009.908327] [<ffffffff810021b1>] do_one_initcall+0x141/0x300
[11009.908330] [<ffffffff81002070>] ? try_to_run_init_process+0x40/0x40
[11009.908333] [<ffffffff8123ff56>] ? trace_hardirqs_on_caller+0x16/0x590
[11009.908337] [<ffffffff8155e926>] ? kasan_unpoison_shadow+0x36/0x50
[11009.908340] [<ffffffff8155e926>] ? kasan_unpoison_shadow+0x36/0x50
[11009.908343] [<ffffffff8155e926>] ? kasan_unpoison_shadow+0x36/0x50
[11009.908346] [<ffffffff8155ea37>] ? __asan_register_globals+0x87/0xa0
[11009.908350] [<ffffffff8144da7b>] do_init_module+0x1d0/0x5ad
[11009.908353] [<ffffffff812f2626>] load_module+0x6666/0x9ba0
[11009.908356] [<ffffffff812e9c90>] ? symbol_put_addr+0x50/0x50
[11009.908361] [<ffffffffa1580037>] ? em28xx_dvb_init.part.3+0x5989/0x5cf4 [em28xx_dvb]
[11009.908366] [<ffffffff812ebfc0>] ? module_frob_arch_sections+0x20/0x20
[11009.908369] [<ffffffff815bc940>] ? open_exec+0x50/0x50
[11009.908374] [<ffffffff811671bb>] ? ns_capable+0x5b/0xd0
[11009.908377] [<ffffffff812f5e58>] SyS_finit_module+0x108/0x130
[11009.908379] [<ffffffff812f5d50>] ? SyS_init_module+0x1f0/0x1f0
[11009.908383] [<ffffffff81004044>] ? lockdep_sys_exit_thunk+0x12/0x14
[11009.908394] [<ffffffff822e6936>] entry_SYSCALL_64_fastpath+0x16/0x76
[11009.908396] Memory state around the buggy address:
[11009.908398] ffff8803bd78aa00: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[11009.908401] ffff8803bd78aa80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[11009.908403] >ffff8803bd78ab00: fc fc fc fc fc fc fc fc 00 00 fc fc fc fc fc fc
[11009.908405] ^
[11009.908407] ffff8803bd78ab80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[11009.908409] ffff8803bd78ac00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[11009.908411] ==================================================================
In order to avoid it, let's set the cached value of the firmware
name to NULL after freeing it. While here, return an error if
the memory allocation fails.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since the exported information can be exposed to user-space, instead of
exporting the entire request context only export the minimum information
needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Prior to 3.13 make allmodconfig KCONFIG_ALLCONFIG=/dev/null used
to be equivalent to make allmodconfig; these days it hardwires MODULES to n.
In fact, any KCONFIG_ALLCONFIG that doesn't set MODULES explicitly is
treated as if it set it to n.
Regression had been introduced by commit cfa98f ("kconfig: do not
override symbols already set"); what happens is that conf_read_simple()
does sym_calc_value(modules_sym) on exit, which leaves SYMBOL_VALID set and
has conf_set_all_new_symbols() skip modules_sym.
It's pretty easy to fix - simply move that call of sym_calc_value()
into the callers, except for the ones in KCONFIG_ALLCONFIG handling.
Objections?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Fixes: cfa98f2e0ae9 ("kconfig: do not override symbols already set") Signed-off-by: Michal Marek <mmarek@suse.com>
[bwh: Backported to 3.16: old code also checked for modules_sym != NULL;
drop the check since it's only useful for other projects] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9ce119f318ba ("tty: Fix GPF in flush_to_ldisc()") fixed a
GPF caused by a line discipline which does not define a receive_buf()
method.
However, the vt driver (and speakup driver also) pushes selection
data directly to the line discipline receive_buf() method via
tty_ldisc_receive_buf(). Fix the same problem in tty_ldisc_receive_buf().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An older patch to convert the API in the s3c i2s driver
ended up passing a const pointer into a function that takes
a non-const pointer, so we now get a warning:
sound/soc/samsung/s3c2412-i2s.c: In function 's3c2412_iis_dev_probe':
sound/soc/samsung/s3c2412-i2s.c:172:9: error: passing argument 3 of 's3c_i2sv2_register_component' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
However, the s3c_i2sv2_register_component() function again
passes the pointer into another function taking a const, so
we just need to change its prototype.
Fixes: eca3b01d0885 ("ASoC: switch over to use snd_soc_register_component() on s3c i2s") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
imx6_pcie_link_up() previously used usleep_range() to wait for the link to
come up. Since it may be called while holding the config spinlock, the
sleep causes a "BUG: scheduling while atomic" error.
Instead of waiting for the link to come up in imx6_pcie_link_up(), do the
waiting in imx6_pcie_wait_for_link(), where we're not holding a lock and
sleeping is allowed.
[bhelgaas: changelog, references to bugzilla and f95d3ae77191] Link: https://bugzilla.kernel.org/show_bug.cgi?id=100031 Fixes: f95d3ae77191 ("PCI: imx6: Wait for retraining") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[bwh: Backported to 3.16: also update the retry loop in
imx6_pcie_wait_for_link() as done upstream in commit 6cbb247e85eb
("PCI: designware: Wait for link to come up with consistent style")] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Remove the remnants of the workaround for erratum ERR005184 which was never
completely implemented. The checks alone don't carry any value as we don't
act properly on the result.
A workaround should be added to the lane speed change in establish_link
later.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This adds the PHY reset into a common error path of
imx6_pcie_establish_link(), deduplicating some of the debug prints. Also
reduce the severity of the "no-link" message in the one place where it is
expected to be hit when no peripheral is attached.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[bwh: Backported to 3.16:
- Error paths were different in imx6_pcie_start_link()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Move imx6_pcie_reset_phy() near the other PHY related functions in the
file. This is a cosmetic change, but also allows to do the following
changes without introducing needless forward declarations.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[bwh: Prerequisite for commit 4d107d3b5a68 ("PCI: imx6: Move link up check into
imx6_pcie_wait_for_link()").
Backported to 3.16: apply the relevant changes from commit 1c7fae18a1fb
("PCI: imx6: Use "u32", not "uint32_t"")] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 8996eafdcbad ("crypto: ahash - ensure statesize is non-zero")
added a check to prevent ahash algorithms from successfully registering
if the import and export functions were not implemented. This prevents
an oops in the hash_accept function of algif_hash. This commit causes
the ccp-crypto module SHA support and AES CMAC support from successfully
registering and causing the ccp-crypto module load to fail because the
ahash import and export functions are not implemented.
Update the CCP Crypto API support to provide import and export support
for ahash algorithms.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
dct_sel_base_off is declared as a u64 but we're only using the lower 32
bits because of a shift wrapping bug. This can possibly truncate the
upper 16 bits of DctSelBaseOffset[47:26], causing us to misdecode the CS
row.
When an SMP Hyper-V guest is running on top of 2012R2 Server and secondary
cpus are sent offline (with echo 0 > /sys/devices/system/cpu/cpu$cpu/online)
the system freeze is observed. This happens due to the fact that on newer
hypervisors (Win8, WS2012R2, ...) vmbus channel handlers are distributed
across all cpus (see init_vp_index() function in drivers/hv/channel_mgmt.c)
and on cpu offlining nobody reassigns them to CPU0. Prevent cpu offlining
when vmbus is loaded until the issue is fixed host-side.
This patch also disables hibernation but it is OK as it is also broken (MCE
error is hit on resume). Suspend still works.
Tested with WS2008R2 and WS2012R2.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Chas Williams <3chas3@gmail.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
An arbitrary amount of time can pass between spin_unlock and
radeon_fence_wait_any, so we need to ensure that nobody frees the
fences from under us.
Based on the analogous fix for amdgpu.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> (v1 + fix) Tested-by: Lutz Euler <lutz.euler@freenet.de>
[ nicolai:
Backport of upstream commit f6ff4f67cdf8455d0a4226eeeaf5af17c37d05eb, with
an additional NULL pointer guard that is required for kernels 3.17 and older.
To be precise, any kernel that does *not* have commit 954605ca3 "drm/radeon:
use common fence implementation for fences, v4" requires this additional
NULL pointer guard.] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On Xen PV, regs->flags doesn't reliably reflect IOPL and the
exit-to-userspace code doesn't change IOPL. We need to context
switch it manually.
I'm doing this without going through paravirt because this is
specific to Xen PV. After the dust settles, we can merge this with
the 32-bit code, tidy up the iopl syscall implementation, and remove
the set_iopl pvop entirely.
Fixes XSA-171.
Reviewewd-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <JBeulich@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/693c3bd7aeb4d3c27c92c622b7d0f554a458173c.1458162709.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ kamal: backport to 3.19-stable: no X86_FEATURE_XENPV so just call
xen_pv_domain() directly ] Acked-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
struct timespec uses 'long' to present second and nanosecond. 'long'
is 64 bits on 64bits machine. ceph MDS expects time stamp to be
encoded as struct ceph_timespec, which uses 'u32' to present second
and nanosecond.
Signed-off-by: Yan, Zheng <zyan@redhat.com> BugLink: http://tracker.ceph.com/issues/15302 BugLink: http://bugs.launchpad.net/bugs/1564950
[ kamal: backport to 3.16-stable: no time stamp in __prepare_send_request() ] Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The ati_remote2 driver expects at least two interfaces with one
endpoint each. If given malicious descriptor that specify one
interface or no endpoints, it will crash in the probe function.
Ensure there is at least two interfaces and one endpoint for each
interface before using it.
The full disclosure: http://seclists.org/bugtraq/2016/Mar/90
Reported-by: Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit d63c7dd5bcb9 ("ipr: Fix out-of-bounds null overwrite") removed
the end of line handling when storing the update_fw sysfs attribute.
This changed the userpace API because it started refusing writes
terminated by a line feed, which broke the update tools we already have.
This patch re-adds that handling, so both a write terminated by a line
feed or not can make it through with the update.
Fixes: d63c7dd5bcb9 ("ipr: Fix out-of-bounds null overwrite") Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Cc: Insu Yun <wuninsu@gmail.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Return value of snprintf is not bound by size value, 2nd argument.
(https://www.kernel.org/doc/htmldocs/kernel-api/API-snprintf.html).
Return value is number of printed chars, can be larger than 2nd
argument. Therefore, it can write null byte out of bounds ofbuffer.
Since snprintf puts null, it does not need to put additional null byte.
Signed-off-by: Insu Yun <wuninsu@gmail.com> Reviewed-by: Shane Seymour <shane.seymour@hpe.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently, smpboot_unpark_threads() is invoked before the incoming CPU
has been added to the scheduler's runqueue structures. This might
potentially cause the unparked kthread to run on the wrong CPU, since the
correct CPU isn't fully set up yet.
That causes a sporadic, hard to debug boot crash triggering on some
systems, reported by Borislav Petkov, and bisected down to:
2a442c9c6453 ("x86: Use common outgoing-CPU-notification code")
This patch places smpboot_unpark_threads() in a CPU hotplug
notifier with priority set so that these kthreads are unparked just after
the CPU has been added to the runqueues.
Reported-and-tested-by: Borislav Petkov <bp@suse.de> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Owen Hofmann <osh@google.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Poison pointer values should be small enough to find a room in
non-mmap'able/hardly-mmap'able space. E.g. on x86 "poison pointer space"
is located starting from 0x0. Given unprivileged users cannot mmap
anything below mmap_min_addr, it should be safe to use poison pointers
lower than mmap_min_addr.
The current poison pointer values of LIST_POISON{1,2} might be too big for
mmap_min_addr values equal or less than 1 MB (common case, e.g. Ubuntu
uses only 0x10000). There is little point to use such a big value given
the "poison pointer space" below 1 MB is not yet exhausted. Changing it
to a smaller value solves the problem for small mmap_min_addr setups.
The values are suggested by Solar Designer:
http://www.openwall.com/lists/oss-security/2015/05/02/6
Signed-off-by: Vasily Kulikov <segoon@openwall.com> Cc: Solar Designer <solar@openwall.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add some sanity check codes before actually accessing the endpoint via
get_endpoint() in order to avoid the invalid access through a
malformed USB descriptor. Mostly just checking bNumEndpoints, but in
one place (snd_microii_spdif_default_get()), the validity of iface and
altsetting index is checked as well.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125 Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: Moritz Muehlenhoff <jmm@inutil.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
create_fixed_stream_quirk() may cause a NULL-pointer dereference by
accessing the non-existing endpoint when a USB device with a malformed
USB descriptor is used.
This patch avoids it simply by adding a sanity check of bNumEndpoints
before the accesses.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125 Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
Reported-by: Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The powermate driver expects at least one valid USB endpoint in its
probe function. If given malicious descriptors that specify 0 for
the number of endpoints, it will crash. Validate the number of
endpoints on the interface before using them.
The full report for this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/85
Reported-by: Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When an inetdev is destroyed, every address assigned to the interface
is removed. And in this scenerio we do two pointless things which can
be very expensive if the number of assigned interfaces is large:
1) Address promotion. We are deleting all addresses, so there is no
point in doing this.
2) A full nf conntrack table purge for every address. We only need to
do this once, as is already caught by the existing
masq_dev_notifier so masq_inet_event() can skip this.
Reported-by: Solar Designer <solar@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net> Tested-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Moritz Muehlenhoff <jmm@inutil.org>
[ luis: backported to 3.16:
- file rename: nf_nat_masquerade_ipv4.c -> ipt_MASQUERADE.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit f37755490fe9b ("tracepoints: Do not trace when cpu is offline") added
a check to make sure that tracepoints only get called when the cpu is
online, as it uses rcu_read_lock_sched() for protection.
Commit 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints
are disabled") added lockdep checks (including rcu checks) for events that
are not enabled to catch possible RCU issues that would only be triggered if
a trace event was enabled. Commit f37755490fe9b only stopped the warnings
when the trace event was enabled but did not prevent warnings if the trace
event was called when disabled.
To fix this, the cpu online check is moved to where the condition is added
to the trace event. This will place the cpu online check in all places that
it may be used now and in the future.
Fixes: f37755490fe9b ("tracepoints: Do not trace when cpu is offline") Fixes: 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints are disabled") Reported-by: Sudeep Holla <sudeep.holla@arm.com> Tested-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The comparisons should be >= since 0x800 and 0x80 require an additional bit
to store.
For the 3 byte case, the existing shift would drop off 2 more bits than
intended.
For the 2 byte case, there should be 5 bits bits in byte 1, and 6 bits in
byte 2.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com> Reviewed-by: Laszlo Ersek <lersek@redhat.com> Cc: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@coreos.com> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
'This is because the pstore filesystem can be backed by UEFI variables,
and (for example) a crash might dump the last kilobytes of the dmesg
into a number of pstore entries, each entry backed by a separate UEFI
variable in the above GUID namespace, and with a variable name
according to the above pattern.
Please see "drivers/firmware/efi/efi-pstore.c".
While this patch series will not prevent the user from deleting those
UEFI variables via the pstore filesystem (i.e., deleting a pstore fs
entry will continue to delete the backing UEFI variable), I think it
would be nice to preserve the possibility for the sysadmin to delete
Linux-created UEFI variables that carry portions of the crash log,
*without* having to mount the pstore filesystem.'
There's also no chance of causing machines to become bricked by
deleting these variables, which is the whole purpose of excluding
things from the whitelist.
Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so
that we don't have to update the string in the future if new variable
name formats are created for crash dump variables.
Reported-by: Laszlo Ersek <lersek@redhat.com> Acked-by: Peter Jones <pjones@redhat.com> Tested-by: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
"rm -rf" is bricking some peoples' laptops because of variables being
used to store non-reinitializable firmware driver data that's required
to POST the hardware.
These are 100% bugs, and they need to be fixed, but in the mean time it
shouldn't be easy to *accidentally* brick machines.
We have to have delete working, and picking which variables do and don't
work for deletion is quite intractable, so instead make everything
immutable by default (except for a whitelist), and make tools that
aren't quite so broad-spectrum unset the immutable flag.
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
[ luis: backported to 3.16:
- use mutex_lock/unlock() instead of inode_lock/unlock()
- use root->d_inode instead of d_inode() ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
All the variables in this list so far are defined to be in the global
namespace in the UEFI spec, so this just further ensures we're
validating the variables we think we are.
Including the guid for entries will become more important in future
patches when we decide whether or not to allow deletion of variables
based on presence in this list.
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Actually translate from ucs2 to utf8 before doing the test, and then
test against our other utf8 data, instead of fudging it.
Signed-off-by: Peter Jones <pjones@redhat.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Translate EFI's UCS-2 variable names to UTF-8 instead of just assuming
all variable names fit in ASCII.
Signed-off-by: Peter Jones <pjones@redhat.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
