A sit interface created without a local or a remote address is linked
into the `sit_net::tunnels_wc` list of its original namespace. When
deleting a network namespace, delete the devices that have been moved.
The following script triggers a null pointer dereference if devices
linked in a deleted `sit_net` remain:
for i in `seq 1 30`; do
ip netns add ns-test
ip netns exec ns-test ip link add dev veth0 type veth peer veth1
ip netns exec ns-test ip link add dev sit$i type sit dev veth0
ip netns exec ns-test ip link set dev sit$i netns $$
ip netns del ns-test
done
for i in `seq 1 30`; do
ip link del dev sit$i
done
Fixes: 5e6700b3bf98f ("sit: add support of x-netns") Signed-off-by: Hristo Venev <hristo@venev.name> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the probe fails, we must disable the regulator that was previously
enabled.
This patch is a follow-up to commit ac88c531a5b3
("net: davicom: Fix regulator not turned off on failed probe") which missed
one case.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the cache_type for the SCSI device is changed, the SCSI layer issues a
MODE_SELECT command. The caching mode details are communicated via a
request buffer associated with the SCSI command with data direction set as
DMA_TO_DEVICE (scsi_mode_select()). When this command reaches the libata
layer, as a part of generic initial setup, libata layer sets up the
scatterlist for the command using the SCSI command (ata_scsi_qc_new()).
This command is then translated by the libata layer into
ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat()). The libata layer treats
this as a non-data command (ata_mselect_caching()), since it only needs an
ATA taskfile to pass the caching on/off information to the device. It does
not need the scatterlist that has been setup, so it does not perform
dma_map_sg() on the scatterlist (ata_qc_issue()). Unfortunately, when this
command reaches the libsas layer (sas_ata_qc_issue()), libsas layer sees it
as a non-data command with a scatterlist. It cannot extract the correct DMA
length since the scatterlist has not been mapped with dma_map_sg() for a
DMA operation. When this partially constructed SAS task reaches pm80xx
LLDD, it results in the following warning:
"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"
Update libsas to handle ATA non-data commands separately so num_scatter and
total_xfer_len remain 0.
Link: https://lore.kernel.org/r/20210318225632.2481291-1-jollys@google.com Fixes: 53de092f47ff ("scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA") Tested-by: Luo Jiaxing <luojiaxing@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jolly Shah <jollys@google.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The root cause is LLVM's assembler has a one-pass design, meaning it
cannot figure out these instruction lengths when the .org directive is
outside of the subsection that they are in, which was changed by the
.arch_extension directive added in the above commit.
Apply the same fix from commit 966a0acce2fc ("arm64/alternatives: move
length validation inside the subsection") to the alternative_endif
macro, shuffling the .org directives so that the length validation
happen will always happen in the same subsections. alternative_insn has
not shown any issue yet but it appears that it could have the same issue
in the future so just preemptively change it.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences") Cc: <stable@vger.kernel.org> # 5.8.x Link: https://github.com/ClangBuiltLinux/linux/issues/1347 Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20210414000803.662534-1-nathan@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline asm's addr operand is marked as input-only, however in
the case where an exception is taken it may be modified by the BIC
instruction on the exception path. Fix the problem by using a temporary
register as the destination register for the BIC instruction.
This does the directory entry name verification for the legacy
"fillonedir" (and compat) interface that goes all the way back to the
dark ages before we had a proper dirent, and the readdir() system call
returned just a single entry at a time.
Nobody should use this interface unless you still have binaries from
1991, but let's do it right.
This came up during discussions about unsafe_copy_to_user() and proper
checking of all the inputs to it, as the networking layer is looking to
use it in a few new places. So let's make sure the _old_ users do it
all right and proper, before we add new ones.
See also commit 8a23eb804ca4 ("Make filldir[64]() verify the directory
entry filename is valid") which did the proper modern interfaces that
people actually use. It had a note:
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
which this now corrects. Note that we really don't care about POSIX and
the presense of '/' in a directory entry, but verify_dirent_name() also
ends up doing the proper name length verification which is what the
input checking discussion was about.
[ Another option would be to remove the support for this particular very
old interface: any binaries that use it are likely a.out binaries, and
they will no longer run anyway since we removed a.out binftm support
in commit eac616557050 ("x86: Deprecate a.out support").
But I'm not sure which came first: getdents() or ELF support, so let's
pretend somebody might still have a working binary that uses the
legacy readdir() case.. ]
commit df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to
block size") introduced the possibility for misaligned roots IO
relative to the underlying device's logical block size. E.g. Android's
default RS roots=2 results in dm_bufio->block_size=1024, which causes
the following EIO if the logical block size of the device is 4096,
given v->data_dev_block_bits=12:
E sd 0 : 0:0:0: [sda] tag#30 request not aligned to the logical block size
E blk_update_request: I/O error, dev sda, sector 10368424 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
E device-mapper: verity-fec: 254:8: FEC 9244672: parity read failed (block 18056): -5
Fix this by onlu using f->roots for dm_bufio blocksize IFF it is
aligned to v->data_dev_block_bits.
Fixes: df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to block size") Cc: stable@vger.kernel.org Signed-off-by: Jaegeuk Kim <jaegeuk@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valid HID_GENERIC type of devices set EV_KEY and EV_ABS by wacom_map_usage.
When *_input_capabilities are reached, those devices should already have
their proper EV_* set. EV_KEY and EV_ABS only need to be set for
non-HID_GENERIC type of devices in *_input_capabilities.
Devices that don't support HID descitoprs will pass back to hid-input for
registration without being accidentally rejected by the introduction of
patch: "Input: refuse to register absolute devices without absinfo"
Fixes: 6ecfe51b4082 ("Input: refuse to register absolute devices without absinfo") Signed-off-by: Ping Cheng <ping.cheng@wacom.com> Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com> Tested-by: Juan Garrido <Juan.Garrido@wacom.com> CC: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Zenbook Flip entry that was added overwrites a previous one
because of a typo:
In file included from drivers/input/serio/i8042.h:23,
from drivers/input/serio/i8042.c:131:
drivers/input/serio/i8042-x86ia64io.h:591:28: error: initialized field overwritten [-Werror=override-init]
591 | .matches = {
| ^
drivers/input/serio/i8042-x86ia64io.h:591:28: note: (near initialization for 'i8042_dmi_noselftest_table[0].matches')
Add the missing separator between the two.
Fixes: b5d6e7ab7fe7 ("Input: i8042 - add ASUS Zenbook Flip to noselftest list") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Marcos Paulo de Souza <mpdesouza@suse.com> Link: https://lore.kernel.org/r/20210323130623.2302402-1-arnd@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.
This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).
Fixes: 0145a7141e59 ("Input: add support for the Samsung S6SY761 touchscreen") Signed-off-by: Caleb Connolly <caleb@connolly.tech> Reviewed-by: Andi Shyti <andi@etezian.org> Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
This patch forbids to add llsec seclevel for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch stops dumping llsec seclevels for monitors which we don't
support yet. Otherwise we will access llsec mib which isn't initialized
for monitors.
This patch forbids to add llsec devkey for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch stops dumping llsec devkeys for monitors which we don't support
yet. Otherwise we will access llsec mib which isn't initialized for
monitors.
This patch forbids to add llsec dev for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
rport_dev_loss_timedout() sets the rport state to SRP_PORT_LOST and the
SCSI target state to SDEV_TRANSPORT_OFFLINE. If this races with
srp_reconnect_work(), a warning is printed:
Mar 27 18:48:07 ictm1604s01h4 kernel: dev_loss_tmo expired for SRP port-18:1 / host18.
Mar 27 18:48:07 ictm1604s01h4 kernel: ------------[ cut here ]------------
Mar 27 18:48:07 ictm1604s01h4 kernel: scsi_internal_device_block(18:0:0:100) failed: ret = -22
Mar 27 18:48:07 ictm1604s01h4 kernel: Call Trace:
Mar 27 18:48:07 ictm1604s01h4 kernel: ? scsi_target_unblock+0x50/0x50 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: starget_for_each_device+0x80/0xb0 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: target_block+0x24/0x30 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: device_for_each_child+0x57/0x90
Mar 27 18:48:07 ictm1604s01h4 kernel: srp_reconnect_rport+0xe4/0x230 [scsi_transport_srp]
Mar 27 18:48:07 ictm1604s01h4 kernel: srp_reconnect_work+0x40/0xc0 [scsi_transport_srp]
Avoid this by not trying to block targets for rports in SRP_PORT_LOST
state.
Link: https://lore.kernel.org/r/20210401091105.8046-1-mwilck@suse.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using the driver in I2S TDM mode, the fsl_esai_startup()
function rewrites the number of slots previously set by the
fsl_esai_set_dai_tdm_slot() function to 2.
To fix this, let's use the saved slot count value or, if TDM
is not used and the number of slots is not set, the driver will use
the default value (2), which is set by fsl_esai_probe().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Nicolin Chen <nicoleotsuka@gmail.com> Link: https://lore.kernel.org/r/20210402081405.9892-1-shc_work@mail.ru Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
They were reading a counter that was configured to ALWAYS_COUNT (ie.
cycles that the GPU is doing something) rather than ALWAYS_ON. This
isn't the thing that userspace is looking for.
Signed-off-by: Rob Clark <robdclark@chromium.org> Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210325012358.1759770-2-robdclark@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang warns about an impossible condition when building with 32-bit
phys_addr_t:
arch/arm/mach-keystone/keystone.c:79:16: error: result of comparison of constant 51539607551 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
mem_end > KEYSTONE_HIGH_PHYS_END) {
~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-keystone/keystone.c:78:16: error: result of comparison of constant 34359738368 with expression of type 'phys_addr_t' (aka 'unsigned int') is always true [-Werror,-Wtautological-constant-out-of-range-compare]
if (mem_start < KEYSTONE_HIGH_PHYS_START ||
~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~
Change the temporary variable to a fixed-size u64 to avoid the warning.
After a short network outage, the dst_entry is timed out and put
in DST_OBSOLETE_DEAD. We are in this code because arp reply comes
from this neighbour after network recovers. There is a potential
race condition that dst_entry is still in DST_OBSOLETE_DEAD.
With that, another neighbour lookup causes more harm than good.
In best case all packets in arp_queue are lost. This is
counterproductive to the original goal of finding a better path
for those packets.
I observed a worst case with 4.x kernel where a dst_entry in
DST_OBSOLETE_DEAD state is associated with loopback net_device.
It leads to an ethernet header with all zero addresses.
A packet with all zero source MAC address is quite deadly with
mac80211, ath9k and 802.11 block ack. It fails
ieee80211_find_sta_by_ifaddr in ath9k (xmit.c). Ath9k flushes tx
queue (ath_tx_complete_aggr). BAW (block ack window) is not
updated. BAW logic is damaged and ath9k transmission is disabled.
Signed-off-by: Tong Zhu <zhutong@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since this message is printed when dynamically allocated spinlocks (e.g.
kzalloc()) are used without initialization (e.g. spin_lock_init()),
suggest to developers to check whether initialization functions for objects
were called, before making developers wonder what annotation is missing.
Fix moving mmc devices with dts aliases as discussed on the lists.
Without this we now have internal eMMC mmc1 show up as mmc2 compared
to the earlier order of devices.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We have a duplicate legacy clock defined for sha2md5_fck that can
sometimes race with clk_disable() with the dts configured clock
for OMAP4_SHA2MD5_CLKCTRL when unused clocks are disabled during
boot causing an "Unhandled fault: imprecise external abort".
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver registers an interrupt handler in _probe, but didn't configure
them until later when the _open function is called. In between, the keypad
can fire an IRQ due to touchpad activity, which the handler ignores. This
causes the kernel to disable the interrupt, blocking the keypad from
working.
Fix this by disabling interrupts before registering the handler.
Additionally, disable them in _close, so that they're only enabled while
open.
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
The bug is fixed by acquiring addr_wq_lock in sctp_destroy_sock
instead of sctp_close.
This addresses CVE-2021-23133.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Fixes: 610236587600 ("bpf: Add new cgroup attach type to enable sock modifications") Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backport of upstream patch 25da4618af240fbec61 ("xen/events: don't
unmask an event channel when an eoi is pending") introduced a
regression for stable kernels 5.10 and older: setting IRQ affinity for
IRQs related to interdomain events would no longer work, as moving the
IRQ to its new cpu was not included in the irq_ack callback for those
events.
Fix that by adding the needed call.
Note that kernels 5.11 and later don't need the explicit moving of the
IRQ to the target cpu in the irq_ack callback, due to a rework of the
affinity setting in kernel 5.11.
CC /tmp/build/perf/util/map.o
util/map.c: In function 'map__new':
util/map.c:109:5: error: '%s' directive output may be truncated writing between 1 and 2147483645 bytes into a region of size 4096 [-Werror=format-truncation=]
109 | "%s/platforms/%s/arch-%s/usr/lib/%s",
| ^~
In file included from /usr/mips-linux-gnu/include/stdio.h:867,
from util/symbol.h:11,
from util/map.c:2:
/usr/mips-linux-gnu/include/bits/stdio2.h:67:10: note: '__builtin___snprintf_chk' output 32 or more bytes (assuming 4294967321) into a destination of size 4096
67 | return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
68 | __bos (__s), __fmt, __va_arg_pack ());
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Since we have the lenghts for what lands in that place, use it to give
the compiler more info and make it happy.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
list_for_each_entry_safe() is only useful if we are deleting nodes in a
linked list within the loop. It doesn't protect against other threads
adding/deleting nodes to the list in parallel. We need to grab
deferred_probe_mutex when traversing the deferred_probe_pending_list.
The license text in this driver is "interesting" and not really obvious
that it is supposed to be able to be distributed in the kernel source
tree. Yes, the MODULE_LICENSE() text says GPL, so it's probably ok, but
to be safe, I am deleting this driver. I will be glad to add it back if
the license is properly sorted out, but for now, this isn't worth the
potential risk, I should have never taken it in the first place.
In RV64, the size of each entry in excp_vect_table is 8 bytes. If the
base of the table is not 8-byte aligned, loading an entry in the table
will raise a misaligned exception. Although such exception will be
handled by opensbi/bbl, this still causes performance degradation.
For multiple split bios, if one of the bio is fail, the whole
should return error to application. But we found there is a race
between bio_integrity_verify_fn and bio complete, which return
io success to application after one of the bio fail. The race as
following:
The bio has been split as two: split and parent. When split
bio completed, it depends on kworker to do endio, while
bio_integrity_verify_fn have been interrupted by parent bio
complete irq handler. Then, parent bio->bi_status which have
been set in irq handler will overwrite by kworker.
In fact, even without the above race, we also need to conside
the concurrency beteen mulitple split bio complete and update
the same parent bi_status. Normally, multiple split bios will
be issued to the same hctx and complete from the same irq
vector. But if we have updated queue map between multiple split
bios, these bios may complete on different hw queue and different
irq vector. Then the concurrency update parent bi_status may
cause the final status error.
Suggested-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Yufen Yu <yuyufen@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210331115359.1125679-1-yuyufen@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
RGB output doesn't allow to change parent clock rate of the display and
PCLK rate is set to 0Hz in this case. The tegra_dc_commit_state() shall
not set the display clock to 0Hz since this change propagates to the
parent clock. The DISP clock is defined as a NODIV clock by the tegra-clk
driver and all NODIV clocks use the CLK_SET_RATE_PARENT flag.
This bug stayed unnoticed because by default PLLP is used as the parent
clock for the display controller and PLLP silently skips the erroneous 0Hz
rate changes because it always has active child clocks that don't permit
rate changes. The PLLP isn't acceptable for some devices that we want to
upstream (like Samsung Galaxy Tab and ASUS TF700T) due to a display panel
clock rate requirements that can't be fulfilled by using PLLP and then the
bug pops up in this case since parent clock is set to 0Hz, killing the
display output.
Don't touch DC clock if pclk=0 in order to fix the problem.
Before this patch, gfs2's freeze function failed to report an error
when the target file system was already frozen as it should (and as
generic vfs function freeze_super does. Similarly, gfs2's thaw function
failed to report an error when trying to thaw a file system that is not
frozen, as vfs function thaw_super does. The errors were checked, but
it always returned a 0 return code.
This patch adds the missing error return codes to gfs2 freeze and thaw.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_OF is disabled, building with 'make W=1' produces warnings
about out of bounds array access:
drivers/gpu/drm/imx/imx-ldb.c: In function 'imx_ldb_set_clock.constprop':
drivers/gpu/drm/imx/imx-ldb.c:186:8: error: array subscript -22 is below array bounds of 'struct clk *[4]' [-Werror=array-bounds]
Add an error check before the index is used, which helps with the
warning, as well as any possible other error condition that may be
triggered at runtime.
The warning could be fixed by adding a Kconfig depedency on CONFIG_OF,
but Liu Ying points out that the driver may hit the out-of-bounds
problem at runtime anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Liu Ying <victor.liu@nxp.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disable guest access to the Trace Filter control registers.
We do not advertise the Trace filter feature to the guest
(ID_AA64DFR0_EL1: TRACE_FILT is cleared) already, but the guest
can still access the TRFCR_EL1 unless we trap it.
This will also make sure that the guest cannot fiddle with
the filtering controls set by a nvhe host.
Cc: Marc Zyngier <maz@kernel.org> Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210323120647.454211-3-suzuki.poulose@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we advertise the ID_AA6DFR0_EL1.TRACEVER for the guest,
when the trace register accesses are trapped (CPTR_EL2.TTA == 1).
So, the guest will get an undefined instruction, if trusts the
ID registers and access one of the trace registers.
Lets be nice to the guest and hide the feature to avoid
unexpected behavior.
Even though this can be done at KVM sysreg emulation layer,
we do this by removing the TRACEVER from the sanitised feature
register field. This is fine as long as the ETM drivers
can handle the individual trace units separately, even
when there are differences among the CPUs.
Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210323120647.454211-2-suzuki.poulose@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch stops dumping llsec params for monitors which we don't support
yet. Otherwise we will access llsec mib which isn't initialized for
monitors.
Reported-by: syzbot+cde43a581a8e5f317bc2@syzkaller.appspotmail.com Signed-off-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20210405003054.256017-16-aahringo@redhat.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch forbids to del llsec seclevel for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
Reported-by: syzbot+fbf4fc11a819824e027b@syzkaller.appspotmail.com Signed-off-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20210405003054.256017-15-aahringo@redhat.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot found general protection fault in crypto_destroy_tfm()[1].
It was caused by wrong clean up loop in llsec_key_alloc().
If one of the tfm array members is in IS_ERR() range it will
cause general protection fault in clean up function [1].
syzbot reported memory leak in peak_usb.
The problem was in case of failure after calling
->dev_init()[2] in peak_usb_create_dev()[1]. The data
allocated int dev_init() wasn't freed, so simple
->dev_free() call fix this problem.
Reported-by: syzbot+91adee8d9ebb9193d22d@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported memory leak in atusb_probe()[1].
The problem was in atusb_alloc_urbs().
Since urb is anchored, we need to release the reference
to correctly free the urb
Reported-by: syzbot+28a246747e0a465127f3@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When changing type with TUNSETLINK ioctl command, set tun->dev->addr_len
to match the appropriate type, using new tun_get_addr_len utility function
which returns appropriate address length for given type. Fixes a
KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=0766d38c656abeace60621896d705743aeefed51
Reported-by: syzbot+001516d86dbe88862cec@syzkaller.appspotmail.com Diagnosed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Phillip Potter <phil@philpotter.co.uk> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A WARN_ON(wdev->conn) would trigger in cfg80211_sme_connect(), if multiple
send_msg(NL80211_CMD_CONNECT) system calls are made from the userland, which
should be anticipated and handled by the wireless driver. Remove this WARN_ON()
to prevent kernel panic if kernel is configured to "panic_on_warn".
Bug reported by syzbot.
Reported-by: syzbot+5f9392825de654244975@syzkaller.appspotmail.com Signed-off-by: Du Cheng <ducheng2@gmail.com> Link: https://lore.kernel.org/r/20210407162756.6101-1-ducheng2@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel creates the action, fills up the netlink response, and then just
deletes the action after notifying userspace.
tc action show action bpf
doesn't list the action.
This happens due to the following sequence when ovr = 1 (replace mode)
is enabled:
tcf_idr_check_alloc is used to atomically check and either obtain
reference for existing action at index, or reserve the index slot using
a dummy entry (ERR_PTR(-EBUSY)).
This is necessary as pointers to these actions will be held after
dropping the idrinfo lock, so bumping the reference count is necessary
as we need to insert the actions, and notify userspace by dumping their
attributes. Finally, we drop the reference we took using the
tcf_action_put_many call in tcf_action_add. However, for the case where
a new action is created due to free index, its refcount remains one.
This when paired with the put_many call leads to the kernel setting up
the action, notifying userspace of its creation, and then tearing it
down. For existing actions, the refcount is still held so they remain
unaffected.
Fortunately due to rtnl_lock serialization requirement, such an action
with refcount == 1 will not be concurrently deleted by anything else, at
best CLS API can move its refcount up and down by binding to it after it
has been published from tcf_idr_insert_many. Since refcount is atleast
one until put_many call, CLS API cannot delete it. Also __tcf_action_put
release path already ensures deterministic outcome (either new action
will be created or existing action will be reused in case CLS API tries
to bind to action concurrently) due to idr lock serialization.
We fix this by making refcount of newly created actions as 2 in ACT API
replace mode. A relaxed store will suffice as visibility is ensured only
after the tcf_idr_insert_many call.
Note that in case of creation or overwriting using CLS API only (i.e.
bind = 1), overwriting existing action object is not allowed, and any
such request is silently ignored (without error).
The refcount bump that occurs in tcf_idr_check_alloc call there for
existing action will pair with tcf_exts_destroy call made from the
owner module for the same action. In case of action creation, there
is no existing action, so no tcf_exts_destroy callback happens.
This means no code changes for CLS API.
Fixes: cae422f379f3 ("net: sched: use reference counting action init") Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointers should be cast with uintptr_t instead of integer. This fixes
warning when compile testing on ARM64:
drivers/clk/socfpga/clk-gate.c: In function ‘socfpga_clk_recalc_rate’:
drivers/clk/socfpga/clk-gate.c:102:7: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Fixes: b7cec13f082f ("clk: socfpga: Look for the GPIO_DB_CLK by its offset") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Dinh Nguyen <dinguyen@kernel.org> Link: https://lore.kernel.org/r/20210314110709.32599-1-krzysztof.kozlowski@canonical.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipv6 bit is wrongly set by the below which causes fatal adapter lookup
engine errors for ipv4 connections while destroying a listener. Fix it to
properly check the local address for ipv6.
Fixes: 3408be145a5d ("RDMA/cxgb4: Fix adapter LE hash errors while destroying ipv6 listening server") Link: https://lore.kernel.org/r/20210331135715.30072-1-bharat@chelsio.com Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Register variables initialized using arithmetic. That leads to
kasan instrumentaton code corrupting the registers contents.
Follow GCC guidlines and use temporary variables for assigning
init values to register variables.
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_unregister(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used. The patch fixes a logical
bug that hasn't been seen in pratice however it is analogus
to the bug fixed in clk_notifier_register().
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_register(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used.
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
When building with W=1, gcc points out that the __packed attribute
on struct qm_eqcr_entry conflicts with the 8-byte alignment
attribute on struct qm_fd inside it:
drivers/soc/fsl/qbman/qman.c:189:1: error: alignment 1 of 'struct qm_eqcr_entry' is less than 8 [-Werror=packed-not-aligned]
I assume that the alignment attribute is the correct one, and
that qm_eqcr_entry cannot actually be unaligned in memory,
so add the same alignment on the outer struct.
card->owner is a required property and since commit 81033c6b584b ("ALSA:
core: Warn on empty module") a warning is issued if it is empty. Add it.
This fixes following warning observed on Lamobo R1:
WARNING: CPU: 1 PID: 190 at sound/core/init.c:207 snd_card_new+0x430/0x480 [snd]
Modules linked in: sun4i_codec(E+) sun4i_backend(E+) snd_soc_core(E) ...
CPU: 1 PID: 190 Comm: systemd-udevd Tainted: G C E 5.10.0-1-armmp #1 Debian 5.10.4-1
Hardware name: Allwinner sun7i (A20) Family
Call trace:
(snd_card_new [snd])
(snd_soc_bind_card [snd_soc_core])
(snd_soc_register_card [snd_soc_core])
(sun4i_codec_probe [sun4i_codec])
Fixes: 45fb6b6f2aa3 ("ASoC: sunxi: add support for the on-chip codec on early Allwinner SoCs")
Related: commit 3c27ea23ffb4 ("ASoC: qcom: Set card->owner to avoid warnings")
Related: commit ec653df2a0cb ("drm/vc4/vc4_hdmi: fill ASoC card owner") Cc: linux-arm-kernel@lists.infradead.org Cc: alsa-devel@alsa-project.org Signed-off-by: Bastian Germann <bage@linutronix.de> Link: https://lore.kernel.org/r/20210331151843.30583-1-bage@linutronix.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.
Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared. After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.
If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.
Fixes: 0795fb2021f0 ("net/ncsi: Stop monitor if channel times out or is inactive") Signed-off-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880d5 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module") Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the if(skb_peek(arrvq) == skb) branch, it calls __skb_dequeue(arrvq) to get
the skb by skb = skb_peek(arrvq). Then __skb_dequeue() unlinks the skb from arrvq
and returns the skb which equals to skb_peek(arrvq). After __skb_dequeue(arrvq)
finished, the skb is freed by kfree_skb(__skb_dequeue(arrvq)) in the first time.
Unfortunately, the same skb is freed in the second time by kfree_skb(skb) after
the branch completed.
My patch removes kfree_skb() in the if(skb_peek(arrvq) == skb) branch, because
this skb will be freed by kfree_skb(skb) finally.
Fixes: cb1b728096f54 ("tipc: eliminate race condition at multicast reception") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Accessing SGE_QBASE_MAP[0-3] and SGE_QBASE_INDEX registers can lead
to SGE missing doorbells under heavy traffic. So, only collect them
when adapter is idle. Also update the regdump range to skip collecting
these registers.
Fixes: 80a95a80d358 ("cxgb4: collect SGE PF/VF queue map") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 3d23a05c75c7 ("gianfar: Enable changing mac addr when if up") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on the IOMMU configuration, the current cache control settings can
result in possible coherency issues. The hardware team has recommended
new settings for the PCI device path to eliminate the issue.
Fixes: 6f595959c095 ("amd-xgbe: Adjust register settings to improve performance") Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the reason of kernel oops when i40e driver removed VFs.
Added new __I40E_VFS_RELEASING state to signalize releasing
process by PF, that it makes possible to exit of reset VF procedure.
Without this patch, it is possible to suspend the VFs reset by
releasing VFs resources procedure. Retrying the reset after the
timeout works on the freed VF memory causing a kernel oops.
Fixes: d43d60e5eb95 ("i40e: ensure reset occurs when disabling VF") Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com> Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add Asym_Pause to supported link modes (it is supported by HW).
Lack of Asym_Pause in supported modes can cause several problems,
i.e. it won't be possible to turn the autonegotiation on
with asymmetric pause settings (i.e. Tx on, Rx off).
Fixes: 4e91bcd5d47a ("i40e: Finish implementation of ethtool get settings") Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.
>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.
So search available sysclk_divs from 2 to 1 other than from 1 to 2.
Fixes: 84fdc00d519f ("ASoC: codec: wm9860: Refactor PLL out freq search") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A sequence counter write section must be serialized or its internal
state can get corrupted. The "xfrm_state_hash_generation" seqcount is
global, but its write serialization lock (net->xfrm.xfrm_state_lock) is
instantiated per network namespace. The write protection is thus
insufficient.
To provide full protection, localize the sequence counter per network
namespace instead. This should be safe as both the seqcount read and
write sections access data exclusively within the network namespace. It
also lays the foundation for transforming "xfrm_state_hash_generation"
data type from seqcount_t to seqcount_LOCKNAME_t in further commits.
Fixes: b65e3d7be06f ("xfrm: state: add sequence count to detect hash resizes") Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Table 30 ("DVFS_MoniVDAC [6:0] Setting Table") in the
BD9571MWV-M Datasheet Rev. 002, the valid voltage range is 600..1100 mV
(settings 0x3c..0x6e). While the lower limit is taken into account (by
setting regulator_desc.linear_min_sel to 0x3c), the upper limit is not.
Fix this by reducing regulator_desc.n_voltages from 0x80 to 0x6f.
Implement support for transferring XDP meta data into skb for
virtio_net driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
Tested with the script at
https://github.com/higebu/virtio_net-xdp-metadata-test.
Signed-off-by: Yuya Kusakabe <yuya.kusakabe@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/bpf/20200225033212.437563-2-yuya.kusakabe@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In some configurations, recovery is optional. So, don't throw an error
when it is not used because e.g. pinctrl settings for recovery are not
provided. Reword the message and make it debug output.
Reported-by: Klaus Kudielka <klaus.kudielka@gmail.com> Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
Use sysfs_lock to synchronize event handler with sysfs paths
in usbip drivers.
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
Use sysfs_lock to protect sysfs paths in stub-dev.
Fuzzing uncovered race condition between sysfs code paths in usbip
drivers. Device connect/disconnect code paths initiated through
sysfs interface are prone to races if disconnect happens during
connect and vice versa.
This problem is common to all drivers while it can be reproduced easily
in vhci_hcd. Add a sysfs_lock to usbip_device struct to protect the paths.
Use this in vhci_hcd to protect sysfs paths. For a complete fix, usip_host
and usip-vudc drivers and the event handler will have to use this lock to
protect the paths. These changes will be done in subsequent patches.
Found by virtue of ipv6 raw sockets not honouring the per-socket
IP{,V6}_FREEBIND setting.
Based on hits found via:
git grep '[.]ip_nonlocal_bind'
We fix both raw ipv6 sockets to honour IP{,V6}_FREEBIND and IP{,V6}_TRANSPARENT,
and we fix sctp sockets to honour IP{,V6}_TRANSPARENT (they already honoured
FREEBIND), and not just the ipv6 'ip_nonlocal_bind' sysctl.
The helper is defined as:
static inline bool ipv6_can_nonlocal_bind(struct net *net, struct inet_sock *inet) {
return net->ipv6.sysctl.ip_nonlocal_bind || inet->freebind || inet->transparent;
}
so this change only widens the accepted opt-outs and is thus a clean bugfix.
I'm not entirely sure what 'fixes' tag to add, since this is AFAICT an ancient bug,
but IMHO this should be applied to stable kernels as far back as possible.
As such I'm adding a 'fixes' tag with the commit that originally added the helper,
which happened in 4.19. Backporting to older LTS kernels (at least 4.9 and 4.14)
would presumably require open-coding it or backporting the helper as well.
Cc: Lorenzo Colitti <lorenzo@google.com> Fixes: 83ba4645152d ("net: add helpers checking if socket can be bound to nonlocal address") Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-By: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Null pointer dereference happens on master->slaves dereference in
teql_destroy() as master is null-pointer.
When qdisc_create() calls teql_qdisc_init() it imediately fails after
check "if (m->dev == dev)" because both devices are teql0, and it does
not set qdisc_priv(sch)->m leaving it zero on error path, then
qdisc_create() imediately calls teql_destroy() which does not expect
zero master pointer and we get OOPS.
Fixes: 87b60cfacf9f ("net_sched: fix error recovery at qdisc creation") Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 924a9bc362a5 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.
This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]
This patch resets mac_header earlier, to get more coverage about this change.
Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.
[1]
BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409
Fixes: 924a9bc362a5 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Balazs Nemeth <bnemeth@redhat.com> Cc: Willem de Bruijn <willemb@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c705 ("HSO: add option hso driver") Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
250 msec timeout is insufficient for some AQ commands. Advice from FW
team was to increase the timeout. Increase to 1 second.
Fixes: 7ec59eeac804 ("ice: Add support for control queues") Signed-off-by: Fabio Pricoco <fabio.pricoco@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KMSAN found uninitialized value at batadv_tt_prepare_tvlv_local_data()
[1], for commit ced72933a5e8ab52 ("batman-adv: use CRC32C instead of CRC16
in TT code") inserted 'reserved' field into "struct batadv_tvlv_tt_data"
and commit 7ea7b4a142758dea ("batman-adv: make the TT CRC logic VLAN
specific") moved that field to "struct batadv_tvlv_tt_vlan_data" but left
that field uninitialized.
Reported-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com> Tested-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Fixes: ced72933a5e8ab52 ("batman-adv: use CRC32C instead of CRC16 in TT code") Fixes: 7ea7b4a142758dea ("batman-adv: make the TT CRC logic VLAN specific") Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org> Reported-by: Rui Salvaterra <rsalvaterra@gmail.com> Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia") Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: linux-arm-kernel@lists.infradead.org Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: <stable@vger.kernel.org> Tested-by: Rui Salvaterra <rsalvaterra@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
