If the userland switches back-and-forth between NL80211_IFTYPE_OCB and
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), there is a
chance where the cleanup cfg80211_leave_ocb() is not called. This leads
to initialization of in-use memory (e.g. init u.ibss while in-use by
u.ocb) due to a shared struct/union within ieee80211_sub_if_data:
Syzbot reports that we may be able to get into a situation where
mac80211 has pending ACK frames on shutdown with hwsim. It appears
that the reason for this is that syzbot uses the wmediumd hooks to
intercept/injection frames, and may shut down hwsim, removing the
radio(s), while frames are pending in the air simulation.
Clean out the pending queue when the interface is stopped, after
this the frames can't be reported back to mac80211 properly anyway.
Syzbot reports that it's possible to hit this from userspace,
by trying to add a station before any other connection setup
has been done. Instead of trying to catch this in some other
way simply remove the warning, that will appropriately reject
the call from userspace.
While the descriptor ID is stored in a 32-bit field in the hardware
descriptor, only 16 bits are used by the hardware and are reported
through the XILINX_DPDMA_CH_DESC_ID register. Failure to handle the
wrap-around results in a descriptor ID mismatch after 65536 frames. Fix
it.
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
If the kernel is compiled with the CONFIG_LOCKDEP option, the conditional
might_sleep_if() deep in kmem_cache_alloc() will generate the following
trace, and potentially cause a deadlock when another LBR event is added:
[] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:196
[] Call Trace:
[] kmem_cache_alloc+0x36/0x250
[] intel_pmu_lbr_add+0x152/0x170
[] x86_pmu_add+0x83/0xd0
Make it symmetric with the release_lbr_buffers() call and mirror the
existing DS buffers.
Fixes: c085fb8774 ("perf/x86/intel/lbr: Support XSAVES for arch LBR read") Signed-off-by: Like Xu <like.xu@linux.intel.com>
[peterz: simplified] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Kan Liang <kan.liang@linux.intel.com> Link: https://lkml.kernel.org/r/20210430052247.3079672-2-like.xu@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
vmlinux.o: warning: objtool: debug_locks_off()+0x23: call to console_verbose() leaves .noinstr.text section
vmlinux.o: warning: objtool: debug_locks_off()+0x19: call to __kasan_check_write() leaves .noinstr.text section
debug_locks_off+0x19/0x40:
instrument_atomic_write at include/linux/instrumented.h:86
(inlined by) __debug_locks_off at include/linux/debug_locks.h:17
(inlined by) debug_locks_off at lib/debug_locks.c:41
Fixes: 6eebad1ad303 ("lockdep: __always_inline more for noinstr") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20210621120120.784404944@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
If the HPD GPIO is not available and drm_probe_ddc fails, we end up
reading the HDMI_HOTPLUG register, but the controller might be powered
off resulting in a CPU hang. Make sure we have the power domain and the
HSM clock powered during the detect cycle to prevent the hang from
happening.
In order to access the HDMI controller, we need to make sure the HSM
clock is enabled. If we were to access it with the clock disabled, the
CPU would completely hang, resulting in an hard crash.
Since we have different code path that would require it, let's move that
clock enable / disable to runtime_pm that will take care of the
reference counting for us.
Revert commit 4514d991d992 ("PCI: PM: Do not read power state in
pci_enable_device_flags()") that is reported to cause PCI device
initialization issues on some systems.
mem_init() currently relies on knowing the boundaries of the crashkernel
reservation to map such region with page granularity for later
unmapping via set_memory_valid(..., 0). If the crashkernel reservation
is deferred, such boundaries are not known when the linear mapping is
created. Simply parse the command line for "crashkernel" and, if found,
create the linear map with NO_BLOCK_MAPPINGS.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Acked-by: James Morse <james.morse@arm.com> Cc: James Morse <james.morse@arm.com> Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/20201119175556.18681-1-catalin.marinas@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the kernel assumes that if RAM starts above 32-bit (or
zone_bits), there is still a ZONE_DMA/DMA32 at the bottom of the RAM and
such constrained devices have a hardwired DMA offset. In practice, we
haven't noticed any such hardware so let's assume that we can expand
ZONE_DMA32 to the available memory if no RAM below 4GB. Similarly,
ZONE_DMA is expanded to the 4GB limit if no RAM addressable by
zone_bits.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Cc: Robin Murphy <robin.murphy@arm.com> Link: https://lore.kernel.org/r/20201118185809.1078362-1-catalin.marinas@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the latest mkimage from U-Boot 2021.04, the generic defconfigs no
longer build, failing with:
/usr/bin/mkimage: verify_header failed for FIT Image support with exit code 1
This is expected after the linked U-Boot commits because '@' is
forbidden in the node names due to the way that libfdt treats nodes with
the same prefix but different unit addresses.
Switch the '@' in the node name to '-'. Drop the unit addresses from the
hash and kernel child nodes because there is only one node so they do
not need to have a number to differentiate them.
It has been reported that usage of memcpy() to/from an iomem mapping is invalid,
and a recent arm64 memcpy update [1] triggers a memory abort when dram-access-quirk
is used on the G12A/G12B platforms.
This adds a local sg_copy_to_buffer which makes usage of io versions of memcpy
when dram-access-quirk is enabled.
When building the kernel wtih gcc-10 or higher using the
CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y flag, the compiler picks a slightly
different set of registers for the inline assembly in cpu_init() that
subsequently results in a corrupt kernel stack as well as remaining in
FIQ mode. If a banked register is used for the last argument, the wrong
version of that register gets loaded into CPSR_c. When building in Arm
mode, the arguments are passed as immediate values and the bug cannot
happen.
This got introduced when Daniel reworked the FIQ handling and was
technically always broken, but happened to work with both clang and gcc
before gcc-10 as long as they picked one of the lower registers.
This is probably an indication that still very few people build the
kernel in Thumb2 mode.
Marek pointed out the problem on IRC, Arnd narrowed it down to this
inline assembly and Russell pinpointed the exact bug.
Change the constraints to force the final mode switch to use a non-banked
register for the argument to ensure that the correct constant gets loaded.
Another alternative would be to always use registers for the constant
arguments to avoid the #ifdef that has now become more complex.
Cc: <stable@vger.kernel.org> # v3.18+ Cc: Daniel Thompson <daniel.thompson@linaro.org> Reported-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Ard Biesheuvel <ardb@kernel.org> Fixes: c0e7f7ee717e ("ARM: 8150/3: fiq: Replace default FIQ handler") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While checking the master status of the DRM file in
drm_is_current_master(), the device's master mutex should be
held. Without the mutex, the pointer fpriv->master may be freed
concurrently by another process calling drm_setmaster_ioctl(). This
could lead to use-after-free errors when the pointer is subsequently
dereferenced in drm_lease_owner().
The callers of drm_is_current_master() from drm_auth.c hold the
device's master mutex, but external callers do not. Hence, we implement
drm_is_current_master_locked() to be used within drm_auth.c, and
modify drm_is_current_master() to grab the device's master mutex
before checking the master status.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com> Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210620110327.4964-2-desmondcheongzx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Irrespective as to whether CONFIG_MODULE_SIG is configured, specifying
"module.sig_enforce=1" on the boot command line sets "sig_enforce".
Only allow "sig_enforce" to be set when CONFIG_MODULE_SIG is configured.
This patch makes the presence of /sys/module/module/parameters/sig_enforce
dependent on CONFIG_MODULE_SIG=y.
When do system reboot, it calls dwc3_shutdown and the whole debugfs
for dwc3 has removed first, when the gadget tries to do deinit, and
remove debugfs for its endpoints, it meets NULL pointer dereference
issue when call debugfs_lookup. Fix it by removing the whole dwc3
debugfs later than dwc3_drd_exit.
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly") Cc: stable <stable@vger.kernel.org> Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ea6932d70e223e02 ("net: make get_net_ns return error if NET_NS is disabled")
That don't result in any changes in the tables generated from that
header.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/perf/trace/beauty/include/linux/socket.h' differs from latest version at 'include/linux/socket.h'
diff -u tools/perf/trace/beauty/include/linux/socket.h include/linux/socket.h
Cc: Changbin Du <changbin.du@intel.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
321827477360934d ("icmp: don't send out ICMP messages with a source address of 0.0.0.0")
That don't result in any change in tooling, as INADDR_ are not used to
generate id->string tables used by 'perf trace'.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers may call stmmac_probe_config_dt() to parse dt, could
call stmmac_remove_config_dt() in error handing after dt parsed, so need
disable clocks in stmmac_remove_config_dt().
Go through all platforms drivers which use stmmac_probe_config_dt(),
none of them disable clocks manually, so it's safe to disable them in
stmmac_remove_config_dt().
Fixes: commit d2ed0a7755fe ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that SLUB redzoning ("slub_debug=Z") checks from
s->object_size rather than from s->inuse (which is normally bumped to
make room for the freelist pointer), so a cache created with an object
size less than 24 would have the freelist pointer written beyond
s->object_size, causing the redzone to be corrupted by the freelist
pointer. This was very visible with "slub_debug=ZF":
BUG test (Tainted: G B ): Right Redzone overwritten
-----------------------------------------------------------------------------
The redzone area for SLUB exists between s->object_size and s->inuse
(which is at least the word-aligned object_size). If a cache were
created with an object_size smaller than sizeof(void *), the in-object
stored freelist pointer would overwrite the redzone (e.g. with boot
param "slub_debug=ZF"):
BUG test (Tainted: G B ): Right Redzone overwritten
-----------------------------------------------------------------------------
Store the freelist pointer out of line when object_size is smaller than
sizeof(void *) and redzoning is enabled.
Additionally remove the "smaller than sizeof(void *)" check under
CONFIG_DEBUG_VM in kmem_cache_sanity_check() as it is now redundant:
SLAB and SLOB both handle small sizes.
(Note that no caches within this size range are known to exist in the
kernel currently.)
Link: https://lkml.kernel.org/r/20210608183955.280836-3-keescook@chromium.org Fixes: 81819f0fc828 ("SLUB core") Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: "Lin, Zhenpeng" <zplin@psu.edu> Cc: Marco Elver <elver@google.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "Actually fix freelist pointer vs redzoning", v4.
This fixes redzoning vs the freelist pointer (both for middle-position
and very small caches). Both are "theoretical" fixes, in that I see no
evidence of such small-sized caches actually be used in the kernel, but
that's no reason to let the bugs continue to exist, especially since
people doing local development keep tripping over it. :)
This patch (of 3):
Instead of repeating "Redzone" and "Poison", clarify which sides of
those zones got tripped. Additionally fix column alignment in the
trailer.
BUG test (Tainted: G B ): Right Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
The earlier commits that slowly resulted in the "Before" reporting were:
d86bd1bece6f ("mm/slub: support left redzone") ffc79d288000 ("slub: use print_hex_dump") 2492268472e7 ("SLUB: change error reporting format to follow lockdep loosely")
I found it by pure code review, that pte_same_as_swp() of unuse_vma()
didn't take uffd-wp bit into account when comparing ptes.
pte_same_as_swp() returning false negative could cause failure to
swapoff swap ptes that was wr-protected by userfaultfd.
Link: https://lkml.kernel.org/r/20210603180546.9083-1-peterx@redhat.com Fixes: f45ec5ff16a7 ("userfaultfd: wp: support swap and page migration") Signed-off-by: Peter Xu <peterx@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> [5.7+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The egress tunnel code uses dst_clone() and directly sets the result
which is wrong because the entry might have 0 refcnt or be already deleted,
causing number of problems. It also triggers the WARN_ON() in dst_hold()[1]
when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and
checking if a reference was actually taken before setting the dst.
Cc: stable@vger.kernel.org Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes: 84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang") Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If cfg80211_pmsr_process_abort() moves all the PMSR requests that
need to be freed into a local list before aborting and freeing them.
As a result, it is possible that cfg80211_pmsr_complete() will run in
parallel and free the same PMSR request.
Fix it by freeing the request in cfg80211_pmsr_complete() only if it
is still in the original pmsr list.
If all net/wireless/certs/*.hex files are deleted, the build
will hang at this point since the 'cat' command will have no
arguments. Do "echo | cat - ..." so that even if the "..."
part is empty, the whole thing won't hang.
The commit cb17ed29a7a5 ("mac80211: parse radiotap header when selecting Tx
queue") moved the code to validate the radiotap header from
ieee80211_monitor_start_xmit to ieee80211_parse_tx_radiotap. This made is
possible to share more code with the new Tx queue selection code for
injected frames. But at the same time, it now required the call of
ieee80211_parse_tx_radiotap at the beginning of functions which wanted to
handle the radiotap header. And this broke the rate parser for radiotap
header parser.
The radiotap parser for rates is operating most of the time only on the
data in the actual radiotap header. But for the 802.11a/b/g rates, it must
also know the selected band from the chandef information. But this
information is only written to the ieee80211_tx_info at the end of the
ieee80211_monitor_start_xmit - long after ieee80211_parse_tx_radiotap was
already called. The info->band information was therefore always 0
(NL80211_BAND_2GHZ) when the parser code tried to access it.
For a 5GHz only device, injecting a frame with 802.11a rates would cause a
NULL pointer dereference because local->hw.wiphy->bands[NL80211_BAND_2GHZ]
would most likely have been NULL when the radiotap parser searched for the
correct rate index of the driver.
Cc: stable@vger.kernel.org Reported-by: Ben Greear <greearb@candelatech.com> Fixes: cb17ed29a7a5 ("mac80211: parse radiotap header when selecting Tx queue") Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
[sven@narfation.org: added commit message] Signed-off-by: Sven Eckelmann <sven@narfation.org> Link: https://lore.kernel.org/r/20210530133226.40587-1-sven@narfation.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides SECTIONS_SHIFT, SECTION_SIZE_BITS is also used to calculate
PAGES_PER_SECTION in makedumpfile just like kernel.
Unfortunately, this arch-dependent macro SECTION_SIZE_BITS changes, e.g.
recently in kernel commit f0b13ee23241 ("arm64/sparsemem: reduce
SECTION_SIZE_BITS"). But user space wants a stable interface to get
this info. Such info is impossible to be deduced from a crashdump
vmcore. Hence append SECTION_SIZE_BITS to vmcoreinfo.
Link: https://lkml.kernel.org/r/20210608103359.84907-1-kernelfans@gmail.com Link: http://lists.infradead.org/pipermail/kexec/2021-June/022676.html Signed-off-by: Pingfan Liu <kernelfans@gmail.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Bhupesh Sharma <bhupesh.sharma@linaro.org> Cc: Kazuhito Hagio <k-hagio@ab.jp.nec.com> Cc: Dave Young <dyoung@redhat.com> Cc: Boris Petkov <bp@alien8.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: James Morse <james.morse@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Dave Anderson <anderson@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If access_ok() or fpregs_soft_set() fails in __fpu__restore_sig() then the
function just returns but does not clear the FPU state as it does for all
other fatal failures.
Clear the FPU state for these failures as well.
Fixes: 72a671ced66d ("x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/87mtryyhhz.ffs@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both Intel and AMD consider it to be architecturally valid for XRSTOR to
fail with #PF but nonetheless change the register state. The actual
conditions under which this might occur are unclear [1], but it seems
plausible that this might be triggered if one sibling thread unmaps a page
and invalidates the shared TLB while another sibling thread is executing
XRSTOR on the page in question.
__fpu__restore_sig() can execute XRSTOR while the hardware registers
are preserved on behalf of a different victim task (using the
fpu_fpregs_owner_ctx mechanism), and, in theory, XRSTOR could fail but
modify the registers.
If this happens, then there is a window in which __fpu__restore_sig()
could schedule out and the victim task could schedule back in without
reloading its own FPU registers. This would result in part of the FPU
state that __fpu__restore_sig() was attempting to load leaking into the
victim task's user-visible state.
Invalidate preserved FPU registers on XRSTOR failure to prevent this
situation from corrupting any state.
[1] Frequent readers of the errata lists might imagine "complex
microarchitectural conditions".
Fixes: 1d731e731c4c ("x86/fpu: Add a fastpath to __fpu__restore_sig()") Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Rik van Riel <riel@surriel.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20210608144345.758116583@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-compacted slowpath uses __copy_from_user() and copies the entire
user buffer into the kernel buffer, verbatim. This means that the kernel
buffer may now contain entirely invalid state on which XRSTOR will #GP.
validate_user_xstate_header() can detect some of that corruption, but that
leaves the onus on callers to clear the buffer.
Prior to XSAVES support, it was possible just to reinitialize the buffer,
completely, but with supervisor states that is not longer possible as the
buffer clearing code split got it backwards. Fixing that is possible but
not corrupting the state in the first place is more robust.
Avoid corruption of the kernel XSAVE buffer by using copy_user_to_xstate()
which validates the XSAVE header contents before copying the actual states
to the kernel. copy_user_to_xstate() was previously only called for
compacted-format kernel buffers, but it works for both compacted and
non-compacted forms.
Using it for the non-compacted form is slower because of multiple
__copy_from_user() operations, but that cost is less important than robust
code in an already slow path.
[ Changelog polished by Dave Hansen ]
Fixes: b860eb8dce59 ("x86/fpu/xstate: Define new functions for clearing fpregs and xstates") Reported-by: syzbot+2067e764dbcd10721e2e@syzkaller.appspotmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Borislav Petkov <bp@suse.de> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Rik van Riel <riel@surriel.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20210608144345.611833074@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the xfeatures bit is 0 and therefore the value in the xsave
storage is not valid, get_xsave_addr() returns NULL and switch_to()
writes the default PKRU. -> FAIL #1!
So that wrecks any copy_to/from_user() on the way back to user space
which hits memory which is protected by the default PKRU value.
Assumed that this does not fail (pure luck) then T1 goes back to user
space and because TIF_NEED_FPU_LOAD is set it ends up in
switch_fpu_return()
__fpregs_load_activate()
if (!fpregs_state_valid()) {
load_XSTATE_from_task();
}
But if nothing touched the FPU between T1 scheduling out and back in,
then the fpregs_state is still valid which means switch_fpu_return()
does nothing and just clears TIF_NEED_FPU_LOAD. Back to user space with
DEFAULT_PKRU loaded. -> FAIL #2!
The fix is simple: if get_xsave_addr() returns NULL then set the
PKRU value to 0 instead of the restrictive default PKRU value in
init_pkru_value.
Some drivers require memory that is marked as EFI boot services
data. In order for this memory to not be re-used by the kernel
after ExitBootServices(), efi_mem_reserve() is used to preserve it
by inserting a new EFI memory descriptor and marking it with the
EFI_MEMORY_RUNTIME attribute.
Under SEV, memory marked with the EFI_MEMORY_RUNTIME attribute needs to
be mapped encrypted by Linux, otherwise the kernel might crash at boot
like below:
Expand the __ioremap_check_other() function to additionally check for
this other type of boot data reserved at runtime and indicate that it
should be mapped encrypted for an SEV guest.
switch_fpu_finish() checks current->mm as indicator for kernel threads.
That's wrong because kernel threads can temporarily use a mm of a user
process via kthread_use_mm().
Several SGX users reported seeing the following message on NUMA systems:
sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.
This turned out to be the memblock code mistakenly throwing away SGX
memory.
=== Full Changelog ===
The 'max_pfn' variable represents the highest known RAM address. It can
be used, for instance, to quickly determine for which physical addresses
there is mem_map[] space allocated. The numa_meminfo code makes an
effort to throw out ("trim") all memory blocks which are above 'max_pfn'.
SGX memory is not considered RAM (it is marked as "Reserved" in the
e820) and is not taken into account by max_pfn. Despite this, SGX memory
areas have NUMA affinity and are enumerated in the ACPI SRAT table. The
existing SGX code uses the numa_meminfo mechanism to look up the NUMA
affinity for its memory areas.
In cases where SGX memory was above max_pfn (usually just the one EPC
section in the last highest NUMA node), the numa_memblock is truncated
at 'max_pfn', which is below the SGX memory. When the SGX code tries to
look up the affinity of this memory, it fails and produces an error message:
sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.
and assigns the memory to NUMA node 0.
Instead of silently truncating the memory block at 'max_pfn' and
dropping the SGX memory, add the truncated portion to
'numa_reserved_meminfo'. This allows the SGX code to later determine
the NUMA affinity of its 'Reserved' area.
Before, numa_meminfo looked like this (from 'crash'):
blk = { start = 0x0, end = 0x2080000000, nid = 0x0 }
{ start = 0x2080000000, end = 0x4000000000, nid = 0x1 }
numa_reserved_meminfo is empty.
With this, numa_meminfo looks like this:
blk = { start = 0x0, end = 0x2080000000, nid = 0x0 }
{ start = 0x2080000000, end = 0x4000000000, nid = 0x1 }
and numa_reserved_meminfo has an entry for node 1's SGX memory:
blk = { start = 0x4000000000, end = 0x4080000000, nid = 0x1 }
[ daveh: completely rewrote/reworked changelog ]
Fixes: 5d30f92e7631 ("x86/NUMA: Provide a range-to-target_node lookup facility") Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Fan Du <fan.du@intel.com> Signed-off-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dave Hansen <dave.hansen@intel.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20210617194657.0A99CB22@viggo.jf.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARCv2 has some configuration dependent registers (r30, r58, r59) which
could be targetted by the compiler. To keep the ABI stable, these were
unconditionally part of the glibc ABI
(sysdeps/unix/sysv/linux/arc/sys/ucontext.h:mcontext_t) however we
missed populating them (by saving/restoring them across signal
handling).
This patch fixes the issue by
- adding arcv2 ABI regs to kernel struct sigcontext
- populating them during signal handling
Change to struct sigcontext might seem like a glibc ABI change (although
it primarily uses ucontext_t:mcontext_t) but the fact is
- it has only been extended (existing fields are not touched)
- the old sigcontext was ABI incomplete to begin with anyways
When a AP queue is switched to soft offline, all pending
requests are purged out of the pending requests list and
'received' by the upper layer like zcrypt device drivers.
This is also done for requests which are already enqueued
into the firmware queue. A request in a firmware queue
may eventually produce an response message, but there is
no waiting process any more. However, the response was
counted with the queue_counter and as this counter was
reset to 0 with the offline switch, the pending response
caused the queue_counter to get negative. The next request
increased this counter to 0 (instead of 1) which caused
the ap code to assume there is nothing to receive and so
the response for this valid request was never tried to
fetch from the firmware queue.
This all caused a queue to not work properly after a
switch offline/online and in the end processes to hang
forever when trying to send a crypto request after an
queue offline/online switch cicle.
Fixed by a) making sure the counter does not drop below 0
and b) on a successful enqueue of a message has at least
a value of 1.
Additionally a warning is emitted, when a reply can't get
assigned to a waiting process. This may be normal operation
(process had timeout or has been killed) but may give a
hint that something unexpected happened (like this odd
behavior described above).
The size of SIE critical section is calculated wrongly
as result of a missed subtraction in commit 0b0ed657fe00
("s390: remove critical section cleanup from entry.S")
Commit c9b8b07cded58 (KVM: x86: Dynamically allocate per-vCPU emulation context)
tries to allocate per-vCPU emulation context dynamically, however, the
x86_emulator slab cache is still exiting after the kvm module is unload
as below after destroying the VM and unloading the kvm module.
Calculate and check the full mmu_role when initializing the MMU context
for the nested MMU, where "full" means the bits and pieces of the role
that aren't handled by kvm_calc_mmu_role_common(). While the nested MMU
isn't used for shadow paging, things like the number of levels in the
guest's page tables are surprisingly important when walking the guest
page tables. Failure to reinitialize the nested MMU context if L2's
paging mode changes can result in unexpected and/or missed page faults,
and likely other explosions.
E.g. if an L1 vCPU is running both a 32-bit PAE L2 and a 64-bit L2, the
"common" role calculation will yield the same role for both L2s. If the
64-bit L2 is run after the 32-bit PAE L2, L0 will fail to reinitialize
the nested MMU context, ultimately resulting in a bad walk of L2's page
tables as the MMU will still have a guest root_level of PT32E_ROOT_LEVEL.
Immediately reset the MMU context when the vCPU's SMM flag is cleared so
that the SMM flag in the MMU role is always synchronized with the vCPU's
flag. If RSM fails (which isn't correctly emulated), KVM will bail
without calling post_leave_smm() and leave the MMU in a bad state.
The bad MMU role can lead to a NULL pointer dereference when grabbing a
shadow page's rmap for a page fault as the initial lookups for the gfn
will happen with the vCPU's SMM flag (=0), whereas the rmap lookup will
use the shadow page's SMM flag, which comes from the MMU (=1). SMM has
an entirely different set of memslots, and so the initial lookup can find
a memslot (SMM=0) and then explode on the rmap memslot lookup (SMM=1).
pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete. It assumes the FLR is complete when a config read returns
valid data.
When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially. The VF may respond to config
reads before the firmware has completed its reset processing. If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.
Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing. Not all NIC firmware supports this feature.
The Broadcom BCM57414 NIC may be a multi-function device. While it does
not advertise an ACS capability, peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
Trying to start a new PIO transfer by writing value 0 in PIO_START register
when previous transfer has not yet completed (which is indicated by value 1
in PIO_START) causes an External Abort on CPU, which results in kernel
panic:
SError Interrupt on CPU0, code 0xbf000002 -- SError
Kernel panic - not syncing: Asynchronous SError Interrupt
To prevent kernel panic, it is required to reject a new PIO transfer when
previous one has not finished yet.
If previous PIO transfer is not finished yet, the kernel may issue a new
PIO request only if the previous PIO transfer timed out.
In the past the root cause of this issue was incorrectly identified (as it
often happens during link retraining or after link down event) and special
hack was implemented in Trusted Firmware to catch all SError events in EL3,
to ignore errors with code 0xbf000002 and not forwarding any other errors
to kernel and instead throw panic from EL3 Trusted Firmware handler.
Links to discussion and patches about this issue:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50
https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/
https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
But the real cause was the fact that during link retraining or after link
down event the PIO transfer may take longer time, up to the 1.44s until it
times out. This increased probability that a new PIO transfer would be
issued by kernel while previous one has not finished yet.
After applying this change into the kernel, it is possible to revert the
mentioned TF-A hack and SError events do not have to be caught in TF-A EL3.
Link: https://lore.kernel.org/r/20210608203655.31228-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Marek Behún <kabel@kernel.org> Cc: stable@vger.kernel.org # 7fbcb5da811b ("PCI: aardvark: Don't rely on jiffies while holding spinlock") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some NVIDIA GPU devices do not work with SBR. Triggering SBR leaves the
device inoperable for the current system boot. It requires a system
hard-reboot to get the GPU device back to normal operating condition
post-SBR. For the affected devices, enable NO_BUS_RESET quirk to avoid the
issue.
This issue will be fixed in the next generation of hardware.
Link: https://lore.kernel.org/r/20210608054857.18963-8-ameynarkhede03@gmail.com Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Sinan Kaya <okaya@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS
automatically disables LTSSM when Secondary Bus Reset is received and
device stops working. Prevent bus reset for these devices. With this
change, the device can be assigned to VMs with VFIO, but it will leak state
between VMs.
Reference: https://e2e.ti.com/support/processors/f/791/t/954382 Link: https://lore.kernel.org/r/20210315102606.17153-1-antti.jarvinen@gmail.com Signed-off-by: Antti Järvinen <antti.jarvinen@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The trace_clock_global() tries to make sure the events between CPUs is
somewhat in order. A global value is used and updated by the latest read
of a clock. If one CPU is ahead by a little, and is read by another CPU, a
lock is taken, and if the timestamp of the other CPU is behind, it will
simply use the other CPUs timestamp.
The lock is also only taken with a "trylock" due to tracing, and strange
recursions can happen. The lock is not taken at all in NMI context.
In the case where the lock is not able to be taken, the non synced
timestamp is returned. But it will not be less than the saved global
timestamp.
The problem arises because when the time goes "backwards" the time
returned is the saved timestamp plus 1. If the lock is not taken, and the
plus one to the timestamp is returned, there's a small race that can cause
the time to go backwards!
The above case shows to reads of trace_clock_global() on the same CPU, but
the second read returns one less than the first read. That is, time when
backwards, and this is not what is allowed by trace_clock_global().
This was triggered by heavy tracing and the ring buffer checker that tests
for the clock going backwards:
A while ago, when the "trace" file was opened, tracing was stopped, and
code was added to stop recording the comms to saved_cmdlines, for mapping
of the pids to the task name.
Code has been added that only records the comm if a trace event occurred,
and there's no reason to not trace it if the trace file is opened.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The saved_cmdlines is used to map pids to the task name, such that the
output of the tracing does not just show pids, but also gives a human
readable name for the task.
If the name is not mapped, the output looks like this:
<...>-1316 [005] ...2 132.044039: ...
Instead of this:
gnome-shell-1316 [005] ...2 132.044039: ...
The names are updated when tracing is running, but are skipped if tracing
is stopped. Unfortunately, this stops the recording of the names if the
top level tracer is stopped, and not if there's other tracers active.
The recording of a name only happens when a new event is written into a
ring buffer, so there is no need to test if tracing is on or not. If
tracing is off, then no event is written and no need to test if tracing is
off or not.
Remove the check, as it hides the names of tasks for events in the
instance buffers.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org> Fixes: 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection") Signed-off-by: Breno Lima <breno.lima@nxp.com> Signed-off-by: Jun Li <jun.li@nxp.com> Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com Signed-off-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d758 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub") Cc: stable@vger.kernel.org Signed-off-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a Use-after-Free found by the syzbot.
The problem is that a skb is taken from the per-session skb queue,
without incrementing the ref count. This leads to a Use-after-Free if
the skb is taken concurrently from the session queue due to a CTS.
syzbot is reporting hung task at register_netdevice_notifier() [1] and
unregister_netdevice_notifier() [2], for cleanup_net() might perform
time consuming operations while CAN driver's raw/bcm/isotp modules are
calling {register,unregister}_netdevice_notifier() on each socket.
Change raw/bcm/isotp modules to call register_netdevice_notifier() from
module's __init function and call unregister_netdevice_notifier() from
module's __exit function, as with gw/j1939 modules are doing.
On 64-bit systems, struct bcm_msg_head has an added padding of 4 bytes between
struct members count and ival1. Even though all struct members are initialized,
the 4-byte hole will contain data from the kernel stack. This patch zeroes out
struct bcm_msg_head before usage, preventing infoleaks to userspace.
... in such circumstances, we do not want to mark the instruction as seen given
the goal is still to jmp-1 rewrite/sanitize dead code, if it is not reachable
from the non-speculative path verification. We do however want to verify it for
safety regardless.
With the patch as-is all the insns that have been marked as seen before the
patch will also be marked as seen after the patch (just with a potentially
different non-zero count). An upcoming patch will also verify paths that are
unreachable in the non-speculative domain, hence this extension is needed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of relying on current env->pass_cnt, use the seen count from the
old aux data in adjust_insn_aux_data(), and expand it to the new range of
patched instructions. This change is valid given we always expand 1:n
with n>=1, so what applies to the old/original instruction needs to apply
for the replacement as well.
Not relying on env->pass_cnt is a prerequisite for a later change where we
want to avoid marking an instruction seen when verified under speculative
execution path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Benedict Schlueter <benedict.schlueter@rub.de> Reviewed-by: Piotr Krysiuk <piotras@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The arm64 entry code suffers from an annoying issue on taking
a NMI, as it sets PMR to a value that actually allows IRQs
to be acknowledged. This is done for consistency with other parts
of the code, and is in the process of being fixed. This shouldn't
be a problem, as we are not enabling interrupts whilst in NMI
context.
However, in the infortunate scenario that we took a spurious NMI
(retired before the read of IAR) *and* that there is an IRQ pending
at the same time, we'll ack the IRQ in NMI context. Too bad.
In order to avoid deadlocks while running something like perf,
teach the GICv3 driver about this situation: if we were in
a context where no interrupt should have fired, transiently
set PMR to a value that only allows NMIs before acking the pending
interrupt, and restore the original value after that.
This papers over the core issue for the time being, and makes
NMIs great again. Sort of.
Fixes: 4d6a38da8e79e94c ("arm64: entry: always set GIC_PRIO_PSR_I_SET during entry") Co-developed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/lkml/20210610145731.1350460-1-maz@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
0day robot reported a 9.2% regression for will-it-scale mmap1 test
case[1], caused by commit 57efa1fe5957 ("mm/gup: prevent gup_fast from
racing with COW during fork").
Further debug shows the regression is due to that commit changes the
offset of hot fields 'mmap_lock' inside structure 'mm_struct', thus some
cache alignment changes.
From the perf data, the contention for 'mmap_lock' is very severe and
takes around 95% cpu cycles, and it is a rw_semaphore
Before commit 57efa1fe5957 adds the 'write_protect_seq', it happens to
have a very optimal cache alignment layout, as Linus explained:
"and before the addition of the 'write_protect_seq' field, the
mmap_sem was at offset 120 in 'struct mm_struct'.
Which meant that count and owner were in two different cachelines,
and then when you have contention and spend time in
rwsem_down_write_slowpath(), this is probably *exactly* the kind
of layout you want.
Because first the rwsem_write_trylock() will do a cmpxchg on the
first cacheline (for the optimistic fast-path), and then in the
case of contention, rwsem_down_write_slowpath() will just access
the second cacheline.
Which is probably just optimal for a load that spends a lot of
time contended - new waiters touch that first cacheline, and then
they queue themselves up on the second cacheline."
After the commit, the rw_semaphore is at offset 128, which means the
'count' and 'owner' fields are now in the same cacheline, and causes
more cache bouncing.
Currently there are 3 "#ifdef CONFIG_XXX" before 'mmap_lock' which will
affect its offset:
The layout above is on 64 bits system with 0day's default kernel config
(similar to RHEL-8.3's config), in which all these 3 options are 'y'.
And the layout can vary with different kernel configs.
Relayouting a structure is usually a double-edged sword, as sometimes it
can helps one case, but hurt other cases. For this case, one solution
is, as the newly added 'write_protect_seq' is a 4 bytes long seqcount_t
(when CONFIG_DEBUG_LOCK_ALLOC=n), placing it into an existing 4 bytes
hole in 'mm_struct' will not change other fields' alignment, while
restoring the regression.
Link: https://lore.kernel.org/lkml/20210525031636.GB7744@xsang-OptiPlex-9020/ Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Feng Tang <feng.tang@intel.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The scpi hwmon shows the sub-zero temperature in an unsigned integer,
which would confuse the users when the machine works in low temperature
environment. This shows the sub-zero temperature in an signed value and
users can get it properly from sensors.
I met a gpu addr bug recently and the kernel log
tells me the pc is memcpy/memset and link register is
radeon_uvd_resume.
As we know, in some architectures, optimized memcpy/memset
may not work well on device memory. Trival memcpy_toio/memset_io
can fix this problem.
BTW, amdgpu has already done it in:
commit ba0b2275a678 ("drm/amdgpu: use memcpy_to/fromio for UVD fw upload"),
that's why it has no this issue on the same gpu and platform.
Signed-off-by: Chen Li <chenli@uniontech.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes PoP noise of around 15ms observed during audio
capture begin.
Enables BCLK and LRCLK in snd_soc_dai_ops prepare call for
introducing some delay before capture start.
(am from https://patchwork.kernel.org/patch/12276369/)
(also found at https://lore.kernel.org/r/20210524142114.18676-1-srivasam@codeaurora.org)
On sunxi boards that use HDMI output, HDMI device probe keeps being
avoided indefinitely with these repeated messages in dmesg:
platform 1ee0000.hdmi: probe deferral - supplier 1ef0000.hdmi-phy
not ready
There's a fwnode_link being created with fw_devlink=on between hdmi
and hdmi-phy nodes, because both nodes have 'compatible' property set.
Fw_devlink code assumes that nodes that have compatible property
set will also have a device associated with them by some driver
eventually. This is not the case with the current sun8i-hdmi
driver.
This commit makes sun8i-hdmi-phy into a proper platform device
and fixes the display pipeline probe on sunxi boards that use HDMI.
In 'rt2880_pmx_group_enable' driver is printing an error and returning
-EBUSY if a pin has been already enabled. This begets anoying messages
in the caller when this happens like the following:
rt2880-pinmux pinctrl: pcie is already enabled
mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
To avoid this just print the already enabled message in the pinctrl
driver and return 0 instead to not confuse the user with a real
bad problem.
In U-boot side, an issue has been encountered when QSPI source clock is
running at low frequency (24 MHz for example), waiting for TCF bit to be
set didn't ensure that all data has been send out the FIFO, we should also
wait that BUSY bit is cleared.
To prevent similar issue in kernel driver, we implement similar behavior
by always waiting BUSY bit to be cleared.
Rounding in PELT calculation happening when entities are attached/detached
of a cfs_rq can result into situations where util/runnable_avg is not null
but util/runnable_sum is. This is normally not possible so we need to
ensure that util/runnable_sum stays synced with util/runnable_avg.
detach_entity_load_avg() is the last place where we don't sync
util/runnable_sum with util/runnbale_avg when moving some sched_entities
The power of "LDO2", "MICBIAS1" and "Mic Det Power" were powered off after
the DAPM widgets were added, and these powers were set by the JD settings
"RT5659_JD_HDA_HEADER" in the probe function. In the codec probe function,
these powers were ignored to prevent them controlled by DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com> Signed-off-by: Jack Yu <jack.yu@realtek.com>
Message-Id: <15fced51977b458798ca4eebf03dafb9@realtek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The X1 Carbon Gen 9 uses two fans instead of one like the previous
generation. This adds support for the second fan. It has been tested
on my X1 Carbon Gen 9 (20XXS00100) and works fine.
The valid selectors for bd70528 bucks are 0 ~ 0xf, so the .n_voltages
should be 16 (0x10). Use 0x10 to make it consistent with BD70528_LDO_VOLTS.
Also remove redundant defines for BD70528_BUCK_VOLTS.
projects / thirdparty / kernel / stable.git / log
