On x86 during boot, clockevent_i8253_disable() can be invoked via
x86_late_time_init -> hpet_time_init() -> pit_timer_init() which happens
with enabled interrupts.
If some of the old i8253 hardware is actually used then lockdep will notice
that i8253_lock is used in hard interrupt context. This causes lockdep to
complain because it observed the lock being acquired with interrupts
enabled and in hard interrupt context.
Make clockevent_i8253_disable() acquire the lock with
raw_spinlock_irqsave() to cure this.
[ tglx: Massage change log and use guard() ]
Fixes: c8c4076723dac ("x86/timer: Skip PIT initialization on modern chipsets") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20250404133116.p-XRWJXf@linutronix.de Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, a local dma_cap_mask_t variable is used to store device
cap_mask within udma_of_xlate(). However, the DMA_PRIVATE flag in
the device cap_mask can get cleared when the last channel is released.
This can happen right after storing the cap_mask locally in
udma_of_xlate(), and subsequent dma_request_channel() can fail due to
mismatch in the cap_mask. Fix this by removing the local dma_cap_mask_t
variable and directly using the one from the dma_device structure.
A warning on driver removal started occurring after commit 9dd05df8403b
("net: warn if NAPI instance wasn't shut down"). Disable tx napi before
deleting it in mt76_dma_cleanup().
Tested with mt7921e but the same pattern can be actually applied to other
mt76 drivers calling mt76_dma_cleanup() during removal. Tx napi is enabled
in their *_dma_init() functions and only toggled off and on again inside
their suspend/resume/reset paths. So it should be okay to disable tx
napi in such a generic way.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2ac515a5d74f ("mt76: mt76x02: use napi polling for tx cleanup") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Tested-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Link: https://patch.msgid.link/20250506115540.19045-1-pchelkin@ispras.ru Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
phy-rcar-gen3-usb2 driver exports 4 PHYs. The timing registers are common
to all PHYs. There is no need to set them every time a PHY is initialized.
Set timing register only when the 1st PHY is initialized.
If device_add() fails, do not use device_unregister() for error
handling. device_unregister() consists two functions: device_del() and
put_device(). device_unregister() should only be called after
device_add() succeeded because device_del() undoes what device_add()
does if successful. Change device_unregister() to put_device() call
before returning from the function.
As comment of device_add() says, 'if device_add() succeeds, you should
call device_del() when you want to get rid of it. If device_add() has
not succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable@vger.kernel.org Fixes: 53d2a715c240 ("phy: Add Tegra XUSB pad controller support") Signed-off-by: Ma Ke <make24@iscas.ac.cn> Acked-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20250303072739.3874987-1-make24@iscas.ac.cn Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function snd_es1968_capture_open() calls the function
snd_pcm_hw_constraint_pow2(), but does not check its return
value. A proper implementation can be found in snd_cx25821_pcm_open().
Add error handling for snd_pcm_hw_constraint_pow2() and propagate its
error code.
The original PPTT code had a bug where the processor subtable length
was not correctly validated when encountering a truncated
acpi_pptt_processor node.
Commit 7ab4f0e37a0f4 ("ACPI PPTT: Fix coding mistakes in a couple of
sizeof() calls") attempted to fix this by validating the size is as
large as the acpi_pptt_processor node structure. This introduced a
regression where the last processor node in the PPTT table is ignored
if it doesn't contain any private resources. That results errors like:
ACPI PPTT: PPTT table found, but unable to locate core XX (XX)
ACPI: SPE must be homogeneous
Furthermore, it fails in a common case where the node length isn't
equal to the acpi_pptt_processor structure size, leaving the original
bug in a modified form.
Correct the regression by adjusting the loop termination conditions as
suggested by the bug reporters. An additional check performed after
the subtable node type is detected, validates the acpi_pptt_processor
node is fully contained in the PPTT table. Repeating the check in
acpi_pptt_leaf_node() is largely redundant as the node is already
known to be fully contained in the table.
The case where a final truncated node's parent property is accepted,
but the node itself is rejected should not be considered a bug.
Fixes: 7ab4f0e37a0f4 ("ACPI PPTT: Fix coding mistakes in a couple of sizeof() calls") Reported-by: Maximilian Heyne <mheyne@amazon.de> Closes: https://lore.kernel.org/linux-acpi/20250506-draco-taped-15f475cd@mheyne-amazon/ Reported-by: Yicong Yang <yangyicong@hisilicon.com> Closes: https://lore.kernel.org/linux-acpi/20250507035124.28071-1-yangyicong@huawei.com/ Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Tested-by: Yicong Yang <yangyicong@hisilicon.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Tested-by: Maximilian Heyne <mheyne@amazon.de> Cc: All applicable <stable@vger.kernel.org> # 7ab4f0e37a0f4: ACPI PPTT: Fix coding mistakes ... Link: https://patch.msgid.link/20250508023025.1301030-1-jeremy.linton@arm.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* The analysis is flawed and it's unclear what problem is being
fixed. There is no difference between wait_event_freezable_timeout()
and wait_event_timeout() with respect to device interrupts. And of
course "the interrupt notifying the finish of an operation happens
during wait_event_freezable_timeout()" -- that's how it's supposed
to work.
* The link at the "Closes:" tag appears to be an unrelated
use-after-free in idxd.
* It introduces a regression: dmatest threads are meant to be
freezable and this change breaks that.
See discussion here:
https://lore.kernel.org/dmaengine/878qpa13fe.fsf@AUSNATLYNCH.amd.com/
If there are still layout segments in the layout plh_return_lsegs list
after a layout return, we should be resetting the state to ensure they
eventually get returned as well.
Fixes: 68f744797edd ("pNFS: Do not free layout segments that are marked for return") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In one of the error paths in qlcnic_sriov_channel_cfg_cmd(), the memory
allocated in qlcnic_sriov_alloc_bc_mbx_args() for mailbox arguments is
not freed. Fix that by jumping to the error path that frees them, by
calling qlcnic_free_mbx_args(). This was found using static analysis.
Fixes: f197a7aa6288 ("qlcnic: VF-PF communication channel implementation") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250512044829.36400-1-abdun.nihaal@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It has been reported that when under a bridge with stp_state=1, the logs
get spammed with this message:
[ 251.734607] fsl_dpaa2_eth dpni.5 eth0: Couldn't decode source port
Further debugging shows the following info associated with packets:
source_port=-1, switch_id=-1, vid=-1, vbid=1
In other words, they are data plane packets which are supposed to be
decoded by dsa_tag_8021q_find_port_by_vbid(), but the latter (correctly)
refuses to do so, because no switch port is currently in
BR_STATE_LEARNING or BR_STATE_FORWARDING - so the packet is effectively
unexpected.
The error goes away after the port progresses to BR_STATE_LEARNING in 15
seconds (the default forward_time of the bridge), because then,
dsa_tag_8021q_find_port_by_vbid() can correctly associate the data plane
packets with a plausible bridge port in a plausible STP state.
Re-reading IEEE 802.1D-1990, I see the following:
"4.4.2 Learning: (...) The Forwarding Process shall discard received
frames."
IEEE 802.1D-2004 further clarifies:
"DISABLED, BLOCKING, LISTENING, and BROKEN all correspond to the
DISCARDING port state. While those dot1dStpPortStates serve to
distinguish reasons for discarding frames, the operation of the
Forwarding and Learning processes is the same for all of them. (...)
LISTENING represents a port that the spanning tree algorithm has
selected to be part of the active topology (computing a Root Port or
Designated Port role) but is temporarily discarding frames to guard
against loops or incorrect learning."
Well, this is not what the driver does - instead it sets
mac[port].ingress = true.
To get rid of the log spam, prevent unexpected data plane packets to
be received by software by discarding them on ingress in the LISTENING
state.
In terms of blame attribution: the prints only date back to commit d7f9787a763f ("net: dsa: tag_8021q: add support for imprecise RX based
on the VBID"). However, the settings would permit a LISTENING port to
forward to a FORWARDING port, and the standard suggests that's not OK.
Fixes: 640f763f98c2 ("net: dsa: sja1105: Add support for Spanning Tree Protocol") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250509113816.2221992-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a situation where after THALT is set high, TGO stays high as
well. Because jiffies are never updated, as we are in a context with
interrupts disabled, we never exit that loop and have a deadlock.
That deadlock was noticed on a sama5d4 device that stayed locked for days.
Use retries instead of jiffies so that the timeout really works and we do
not have a deadlock anymore.
Previously, when reducing a qdisc's limit via the ->change() operation, only
the main skb queue was trimmed, potentially leaving packets in the gso_skb
list. This could result in NULL pointer dereference when we only check
sch->limit against sch->q.qlen.
This patch introduces a new helper, qdisc_dequeue_internal(), which ensures
both the gso_skb list and the main queue are properly flushed when trimming
excess packets. All relevant qdiscs (codel, fq, fq_codel, fq_pie, hhf, pie)
are updated to use this helper in their ->change() routines.
Fixes: 76e3cc126bb2 ("codel: Controlled Delay AQM") Fixes: 4b549a2ef4be ("fq_codel: Fair Queue Codel AQM") Fixes: afe4fd062416 ("pkt_sched: fq: Fair Queue packet scheduler") Fixes: ec97ecf1ebe4 ("net: sched: add Flow Queue PIE packet scheduler") Fixes: 10239edf86f1 ("net-qdisc-hhf: Heavy-Hitter Filter (HHF) qdisc") Fixes: d4b36210c2e6 ("net: pkt_sched: PIE AQM scheme") Reported-by: Will <willsroot@protonmail.com> Reported-by: Savy <savy@syst3mfailure.io> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
spi_test_print_hex_dump() prints buffers holding less than 1024 bytes in
full. Larger buffers are truncated: only the first 512 and the last 512
bytes are printed, separated by a truncation message. The latter is
confusing in case the buffer holds exactly 1024 bytes, as all data is
printed anyway.
Fix this by printing buffers holding up to and including 1024 bytes in
full.
When memory is insufficient, the allocation of nfs_lock_context in
nfs_get_lock_context() fails and returns -ENOMEM. If we mistakenly treat
an nfs4_unlockdata structure (whose l_ctx member has been set to -ENOMEM)
as valid and proceed to execute rpc_run_task(), this will trigger a NULL
pointer dereference in nfs4_locku_prepare. For example:
Free the allocated nfs4_unlockdata when nfs_get_lock_context() fails and
return NULL to terminate subsequent rpc_run_task, preventing NULL pointer
dereference.
Fixes: f30cb757f680 ("NFS: Always wait for I/O completion before unlock") Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Link: https://lore.kernel.org/r/20250417072508.3850532-1-lilingfeng3@huawei.com Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function rxe_create_cq, when rxe_cq_from_init fails, the function
rxe_cleanup will be called to handle the allocated resources. In fact,
some memory resources have already been freed in the function
rxe_cq_from_init. Thus, this problem will occur.
The solution is to let rxe_cleanup do all the work.
Follow the pattern of other drivers and use aligned_s64 for the
timestamp. This will ensure that the timestamp is correctly aligned on
all architectures.
Fixes: a5bf6fdd19c3 ("iio:chemical:sps30: Fix timestamp alignment") Signed-off-by: David Lechner <dlechner@baylibre.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://patch.msgid.link/20250417-iio-more-timestamp-alignment-v1-5-eafac1e22318@baylibre.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On architectures where an s64 is not 64-bit aligned, this may result
insufficient alignment of the timestamp and the structure being too small.
Use aligned_s64 to force the alignment.
Fixes: a1caeebab07e ("iio: adc: ad7768-1: Fix too small buffer passed to iio_push_to_buffers_with_timestamp()") # aligned_s64 newer Reported-by: David Lechner <dlechner@baylibre.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Reviewed-by: David Lechner <dlechner@baylibre.com> Link: https://patch.msgid.link/20250413103443.2420727-3-jic23@kernel.org Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(1), (2) means that the model has hardware GPIO for WLAN, you can call
WMIMethod(DEVS, 0x00010011, 1 or 0) to turn WLAN on/off.
(3), (4) means that the model doesn’t have hardware GPIO, you need to use
API or driver library to turn WLAN on/off, and call
WMIMethod(DEVS, 0x00010012, 1 or 0) to set WLAN LED status.
After you set WLAN LED status, you can see the WLAN status is changed with
WMIMethod(DSTS, 0x00010011). Because the status is recorded lastly
(ex: Windows), you can use it for synchronization.
(5) means that the model doesn’t have WLAN device.
WLAN is the ONLY special case with upper rule.
"""
The wlan_ctrl_by_user flag should be set on 0x0003000? ((3), (4) above)
return values, but the flag mistakenly also gets set on laptops with
0x0005000? ((1), (2)) return values. This is causing rfkill problems on
laptops where 0x0005000? is returned.
Fix the check to only set the wlan_ctrl_by_user flag for 0x0003000?
return values.
do_umount() analogue of the race fixed in 119e1ef80ecf "fix
__legitimize_mnt()/mntput() race". Here we want to make sure that
if __legitimize_mnt() doesn't notice our lock_mount_hash(), we will
notice their refcount increment. Harder to hit than mntput_no_expire()
one, fortunately, and consequences are milder (sync umount acting
like umount -l on a rare race with RCU pathwalk hitting at just the
wrong time instead of use-after-free galore mntput_no_expire()
counterpart used to be hit). Still a bug...
Fixes: 48a066e72d97 ("RCU'd vfsmounts") Reviewed-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The original nvme subsystem design didn't have a CONNECTING state; the
state machine allowed transitions from RESETTING to LIVE directly.
With the introduction of nvme fabrics the CONNECTING state was
introduce. Over time the nvme-pci started to use the CONNECTING state as
well.
Eventually, a bug fix for the nvme-fc started to depend that the only
valid transition to LIVE was from CONNECTING. Though this change didn't
update the firmware update handler which was still depending on
RESETTING to LIVE transition.
The simplest way to address it for the time being is to switch into
CONNECTING state before going to LIVE state.
Fixes: d2fe192348f9 ("nvme: only allow entering LIVE from CONNECTING state") Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Daniel Wagner <wagi@kernel.org> Closes: https://lore.kernel.org/all/0134ea15-8d5f-41f7-9e9a-d7e6d82accaa@roeck-us.net Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix MAX_REG_OFFSET to point to the last register in 'pt_regs' and not to
the marker itself, which could allow regs_get_register() to return an
invalid offset.
Fixes: 40e084a506eb ("MIPS: Add uprobes support.") Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Here the lack of marking allows the overall structure to not be
sufficiently aligned resulting in misplacement of the timestamp
in iio_push_to_buffers_with_timestamp(). Use aligned_s64 to
force the alignment on all architectures.
Fixes: 7c0299e879dd ("iio: adc: Add support for DLN2 ADC") Reported-by: David Lechner <dlechner@baylibre.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Reviewed-by: David Lechner <dlechner@baylibre.com> Link: https://patch.msgid.link/20250413103443.2420727-4-jic23@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
wait_event_interruptible_timeout returns a long
The return value was being assigned to an int causing an integer overflow
when the remaining jiffies > INT_MAX which resulted in random error
returns.
Use a long return value, converting to the int ioctl return only on error.
Fixes: bb99794a4792 ("usb: usbtmc: Add ioctl for vendor specific read") Cc: stable@vger.kernel.org Signed-off-by: Dave Penkler <dpenkler@gmail.com> Link: https://lore.kernel.org/r/20250502070941.31819-4-dpenkler@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value, converting to the int ioctl return only on
error.
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value and convert to int ioctl return only on error.
When the return value of wait_event_interruptible_timeout was <= INT_MAX
the number of remaining jiffies was returned which has no meaning for the
user. Return 0 on success.
Reported-by: Michael Katzmann <vk2bea@gmail.com> Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Cc: stable@vger.kernel.org Signed-off-by: Dave Penkler <dpenkler@gmail.com> Link: https://lore.kernel.org/r/20250502070941.31819-2-dpenkler@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbtmc_read() calls usbtmc_generic_read()
which uses interruptible sleep, but usbtmc_read()
itself uses uninterruptble sleep for mutual exclusion
between threads. That makes no sense.
Both should use interruptible sleep.
Fixes: 5b775f672cc99 ("USB: add USB test and measurement class driver") Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250430134810.226015-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch ensures that the UCSI driver waits for all pending tasks in the
ucsi_displayport_work workqueue to finish executing before proceeding with
the partner removal.
Cc: stable <stable@kernel.org> Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode") Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Benson Leung <bleung@chromium.org> Link: https://lore.kernel.org/r/20250424084429.3220757-3-akuchynski@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes Type-C Compliance Test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
The compliance tester moves into SNK_UNATTACHED during toggling and
expects the PUT to apply Rp after tPDDebounce of detection. If the port
is in SNK_TRY_WAIT_DEBOUNCE, it will move into SRC_TRYWAIT immediately
and apply Rp. This violates TD 4.7.5.V.3, where the tester confirms that
the PUT attaches Rp after the transitions to Unattached.SNK for
tPDDebounce.
Change the tcpm_set_state delay between SNK_TRY_WAIT_DEBOUNCE and
SRC_TRYWAIT to tPDDebounce.
Fixes: a0a3e04e6b2c ("staging: typec: tcpm: Check for Rp for tPDDebounce") Cc: stable <stable@kernel.org> Signed-off-by: RD Babiera <rdbabiera@google.com> Reviewed-by: Badhri Jagan Sridharan <badhri@google.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20250429234703.3748506-2-rdbabiera@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is connected to the OTG port, the tegra_xhci_id_work()
routine transitions the PHY to host mode and calls xhci_hub_control()
with the SetPortFeature command to enable port power.
In certain cases, the XHCI controller may be in a low-power state
when this operation occurs. If xhci_hub_control() is invoked while
the controller is suspended, the PORTSC register may return 0xFFFFFFFF,
indicating a read failure. This causes xhci_hc_died() to be triggered,
leading to host controller shutdown.
To prevent this, ensure the controller is fully resumed before
interacting with hardware registers by calling pm_runtime_get_sync()
prior to the host mode transition and xhci_hub_control().
Fixes: f836e7843036 ("usb: xhci-tegra: Add OTG support") Cc: stable <stable@kernel.org> Signed-off-by: Jim Lin <jilin@nvidia.com> Signed-off-by: Wayne Chang <waynec@nvidia.com> Link: https://lore.kernel.org/r/20250422114001.126367-1-waynec@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We identified a bug where the ST_RC bit in the status register was not
being acknowledged after clearing the CTRL_RUN bit in the control
register. This could lead to unexpected behavior in the USB gadget
drivers.
This patch resolves the issue by adding the necessary code to explicitly
acknowledge ST_RC after clearing CTRL_RUN based on the programming
sequence, ensuring proper state transition.
Currently quota recovery is synchronized with unmount using sb->s_umount
semaphore. That is however prone to deadlocks because
flush_workqueue(osb->ocfs2_wq) called from umount code can wait for quota
recovery to complete while ocfs2_finish_quota_recovery() waits for
sb->s_umount semaphore.
Grabbing of sb->s_umount semaphore in ocfs2_finish_quota_recovery() is
only needed to protect that function from disabling of quotas from
ocfs2_dismount_volume(). Handle this problem by disabling quota recovery
early during unmount in ocfs2_dismount_volume() instead so that we can
drop acquisition of sb->s_umount from ocfs2_finish_quota_recovery().
Link: https://lkml.kernel.org/r/20250424134515.18933-6-jack@suse.cz Fixes: 5f530de63cfc ("ocfs2: Use s_umount for quota recovery protection") Signed-off-by: Jan Kara <jack@suse.cz> Reported-by: Shichangkuo <shi.changkuo@h3c.com> Reported-by: Murad Masimov <m.masimov@mt-integration.ru> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Tested-by: Heming Zhao <heming.zhao@suse.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Joel Becker <jlbec@evilplan.org> Cc: Jun Piao <piaojun@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will need ocfs2 recovery thread to acknowledge transitions of
recovery_state when disabling particular types of recovery. This is
similar to what currently happens when disabling recovery completely, just
more general. Implement the handshake and use it for exit from recovery.
Link: https://lkml.kernel.org/r/20250424134515.18933-5-jack@suse.cz Fixes: 5f530de63cfc ("ocfs2: Use s_umount for quota recovery protection") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Tested-by: Heming Zhao <heming.zhao@suse.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Joel Becker <jlbec@evilplan.org> Cc: Jun Piao <piaojun@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Murad Masimov <m.masimov@mt-integration.ru> Cc: Shichangkuo <shi.changkuo@h3c.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "ocfs2: Fix deadlocks in quota recovery", v3.
This implements another approach to fixing quota recovery deadlocks. We
avoid grabbing sb->s_umount semaphore from ocfs2_finish_quota_recovery()
and instead stop quota recovery early in ocfs2_dismount_volume().
This patch (of 3):
We will need more recovery states than just pure enable / disable to fix
deadlocks with quota recovery. Switch osb->disable_recovery to enum.
Link: https://lkml.kernel.org/r/20250424134301.1392-1-jack@suse.cz Link: https://lkml.kernel.org/r/20250424134515.18933-4-jack@suse.cz Fixes: 5f530de63cfc ("ocfs2: Use s_umount for quota recovery protection") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Tested-by: Heming Zhao <heming.zhao@suse.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Cc: Murad Masimov <m.masimov@mt-integration.ru> Cc: Shichangkuo <shi.changkuo@h3c.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 'lookup_or_create_module_kobject()', an internal kobject is created
using 'module_ktype'. So call to 'kobject_put()' on error handling
path causes an attempt to use an uninitialized completion pointer in
'module_kobject_release()'. In this scenario, we just want to release
kobject without an extra synchronization required for a regular module
unloading process, so adding an extra check whether 'complete()' is
actually required makes 'kobject_put()' safe.
Marek reported seeing a NULL pointer fault in the xenbus_thread
callstack:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: e030:__wake_up_common+0x4c/0x180
Call Trace:
<TASK>
__wake_up_common_lock+0x82/0xd0
process_msg+0x18e/0x2f0
xenbus_thread+0x165/0x1c0
process_msg+0x18e is req->cb(req). req->cb is set to xs_wake_up(), a
thin wrapper around wake_up(), or xenbus_dev_queue_reply(). It seems
like it was xs_wake_up() in this case.
It seems like req may have woken up the xs_wait_for_reply(), which
kfree()ed the req. When xenbus_thread resumes, it faults on the zero-ed
data.
Linux Device Drivers 2nd edition states:
"Normally, a wake_up call can cause an immediate reschedule to happen,
meaning that other processes might run before wake_up returns."
... which would match the behaviour observed.
Change to keeping two krefs on each request. One for the caller, and
one for xenbus_thread. Each will kref_put() when finished, and the last
will free it.
This use of kref matches the description in
Documentation/core-api/kref.rst
Device tree bindings state that the clock is optional for UHCI platform
controllers, and some existing device trees don't provide those - such
as those for VIA/WonderMedia devices.
The driver however fails to probe now if no clock is provided, because
devm_clk_get returns an error pointer in such case.
Switch to devm_clk_get_optional instead, so that it could probe again
on those platforms where no clocks are given.
The inclinometer channels were previously defined with 14 realbits.
However, the ADIS16201 datasheet states the resolution for these output
channels is 12 bits (Page 14, text description; Page 15, table 7).
Correct the realbits value to 12 to accurately reflect the hardware.
Fixes: f7fe1d1dd5a5 ("staging: iio: new adis16201 driver") Cc: stable@vger.kernel.org Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com> Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com> Link: https://patch.msgid.link/20250421131539.912966-1-gshahrouzi@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading multiple consecutive registers, only the first one is read
properly. This is due to missing chip select deassert and assert again
between first and second 16bit transfer, as shown in the datasheet AD7606C-16, rev 0, figure 110.
Fixes: f2a22e1e172f ("iio: adc: ad7606: Add support for software mode for ad7616") Reviewed-by: David Lechner <dlechner@baylibre.com> Signed-off-by: Angelo Dureghello <adureghello@baylibre.com> Link: https://patch.msgid.link/20250418-wip-bl-ad7606-fix-reg-access-v3-1-d5eeb440c738@baylibre.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove erroneous subtraction of 4 from the total FIFO depth read from
device tree. The stored depth is for checking against total capacity,
not initial vacancy. This prevented writes near the FIFO's full size.
The check performed just before data transfer, which uses live reads of
the TDFV register to determine current vacancy, correctly handles the
initial Depth - 4 hardware state and subsequent FIFO fullness.
Fixes: 4a965c5f89de ("staging: add driver for Xilinx AXI-Stream FIFO v4.1 IP core") Cc: stable@vger.kernel.org Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com> Link: https://lore.kernel.org/r/20250419012937.674924-1-gshahrouzi@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The axis-fifo driver performs a full hardware reset (via
reset_ip_core()) in several error paths within the read and write
functions. This reset flushes both TX and RX FIFOs and resets the
AXI-Stream links.
Allow the user to handle the error without causing hardware disruption
or data loss in other FIFO paths.
Fixes: 4a965c5f89de ("staging: add driver for Xilinx AXI-Stream FIFO v4.1 IP core") Cc: stable@vger.kernel.org Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com> Link: https://lore.kernel.org/r/20250419004306.669605-1-gshahrouzi@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode setting logic in ad7816_store_mode was reversed due to
incorrect handling of the strcmp return value. strcmp returns 0 on
match, so the `if (strcmp(buf, "full"))` block executed when the
input was not "full".
This resulted in "full" setting the mode to AD7816_PD (power-down) and
other inputs setting it to AD7816_FULL.
Fix this by checking it against 0 to correctly check for "full" and
"power-down", mapping them to AD7816_FULL and AD7816_PD respectively.
[ 5.989588] psmouse serio1: synaptics: Your touchpad (PNP: TOS0213 PNP0f03) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
[ 6.039923] psmouse serio1: synaptics: Touchpad model: 1, fw: 9.32, id: 0x1e2a1, caps: 0xf00223/0x840300/0x12e800/0x52d884, board id: 3322, fw id: 2658004
The board is labelled TM3322.
Present on the Toshiba / Dynabook Portege X30-D and possibly others.
Confirmed working well with psmouse.synaptics_intertouch=1 and local build.
When VLAN filtering is off, we configure the switch to forward, but not
learn on VLAN table misses. This effectively disables learning while not
filtering.
Fix this by switching to forward and learn. Setting the learning disable
register will still control whether learning actually happens.
Allow reserved multicast to ignore VLAN membership so STP and other
management protocols work without a PVID VLAN configured when using a
vlan aware bridge.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Region locking introduced in v5.6-rc4 contained three macros to handle
the region locks: ahash_bucket_start(), ahash_bucket_end() which gave
back the start and end hash bucket values belonging to a given region
lock and ahash_region() which should give back the region lock belonging
to a given hash bucket. The latter was incorrect which can lead to a
race condition between the garbage collector and adding new elements
when a hash type of set is defined with timeouts.
Fixes: f66ee0410b1c ("netfilter: ipset: Fix "INFO: rcu detected stall in hash_xxx" reports") Reported-by: Kota Toda <kota.toda@gmo-cybersecurity.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As reported by Sebastian Andrzej Siewior the use of local_bh_disable()
is only feasible in uni processor systems to update the modification rules.
The usual use-case to update the modification rules is to update the data
of the modifications but not the modification types (AND/OR/XOR/SET) or
the checksum functions itself.
To omit additional memory allocations to maintain fast modification
switching times, the modification description space is doubled at gw-job
creation time so that only the reference to the active modification
description is changed under rcu protection.
Rename cgw_job::mod to cf_mod and make it a RCU pointer. Allocate in
cgw_create_job() and free it together with cgw_job in
cgw_job_free_rcu(). Update all users to dereference cgw_job::cf_mod with
a RCU accessor and if possible once.
[bigeasy: Replace mod1/mod2 from the Oliver's original patch with dynamic
allocation, use RCU annotation and accessor]
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Closes: https://lore.kernel.org/linux-can/20231031112349.y0aLoBrz@linutronix.de/ Fixes: dd895d7f21b2 ("can: cangw: introduce optional uid to reference created routing jobs") Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://patch.msgid.link/20250429070555.cs-7b_eZ@linutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kvfree_rcu() and kfree_rcu() APIs are hazardous in that if you forget
the second argument, it works, but might sleep. This sleeping can be a
correctness bug from atomic contexts, and even in non-atomic contexts
it might introduce unacceptable latencies. This commit therefore adds
kvfree_rcu_mightsleep() and kfree_rcu_mightsleep(), which will replace
the single-argument kvfree_rcu() and kfree_rcu(), respectively.
This commit enables a series of commits that switch from single-argument
kvfree_rcu() and kfree_rcu() to their _mightsleep() counterparts. Once
all of these commits land, the single-argument versions will be removed.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: 511e64e13d8c ("can: gw: fix RCU/BH usage in cgw_create_job()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit fb8696ab14ad ("can: gw: synchronize rcu operations
before removing gw job entry") added three synchronize_rcu() calls
to make sure one rcu grace period was observed before freeing
a "struct cgw_job" (which are tiny objects).
This should be converted to call_rcu() to avoid adding delays
in device / network dismantles.
Use the rcu_head that was already in struct cgw_job,
not yet used.
Link: https://lore.kernel.org/all/20220207190706.1499190-1-eric.dumazet@gmail.com Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: 511e64e13d8c ("can: gw: fix RCU/BH usage in cgw_create_job()") Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch replaces the manual Netlink attribute iteration in
output_userspace() with nla_for_each_nested(), which ensures that only
well-formed attributes are processed.
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
In newer version of the SBC specs, we have a NDOB bit that indicates there
is no data buffer that gets written out. If this bit is set using commands
like "sg_write_same --ndob" we will crash in target_core_iblock/file's
execute_write_same handlers when we go to access the se_cmd->t_data_sg
because its NULL.
This patch adds a check for the NDOB bit in the common WRITE SAME code
because we don't support it. And, it adds a check for zero SG elements in
each handler in case the initiator tries to send a normal WRITE SAME with
no data buffer.
Link: https://lore.kernel.org/r/20220628022325.14627-2-michael.christie@oracle.com Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blammed commit copied to argv the size of the reallocated argv,
instead of the size of the old_argv, thus reading and copying from
past the old_argv allocated memory.
usb_phy_init() may return an error code if e.g. its implementation fails
to prepare/enable some clocks. And properly rollback on probe error path
by calling the counterpart usb_phy_shutdown().
Found by Linux Verification Center (linuxtesting.org).
With ACPI in place, gicv2m_get_fwnode() is registered with the pci
subsystem as pci_msi_get_fwnode_cb(), which may get invoked at runtime
during a PCI host bridge probe. But, the call back is wrongly marked as
__init, causing it to be freed, while being registered with the PCI
subsystem and could trigger:
Unable to handle kernel paging request at virtual address ffff8000816c0400
gicv2m_get_fwnode+0x0/0x58 (P)
pci_set_bus_msi_domain+0x74/0x88
pci_register_host_bridge+0x194/0x548
This is easily reproducible on a Juno board with ACPI boot.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221121140048.534395323@linutronix.de
Stable-dep-of: 3318dc299b07 ("irqchip/gic-v2m: Prevent use after free of gicv2m_get_fwnode()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The patch does permit the offending YUV420 @ 59.94 phy_freq and
vclk_freq mode to match in calculations. It also results in all
fractional rates being unavailable for use. This was unintended
and requires the patch to be reverted.
In of_modalias(), if the buffer happens to be too small even for the 1st
snprintf() call, the len parameter will become negative and str parameter
(if not NULL initially) will point beyond the buffer's end. Add the buffer
overflow check after the 1st snprintf() call and fix such check after the
strlen() call (accounting for the terminating NUL char).
Fixes: bc575064d688 ("of/device: use of_property_for_each_string to parse compatible strings") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/bbfc6be0-c687-62b6-d015-5141b93f313e@omp.ru Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: "Uwe Kleine-König" <ukleinek@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX7D only has one PCIe controller, so controller_id should always be
0. The previous code is incorrect although yielding the correct result.
Fix by removing "IMX7D" from the switch case branch.
Fixes: 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ") Link: https://lore.kernel.org/r/20241126075702.4099164-5-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Frank Li <Frank.Li@nxp.com>
[Because this switch case does more than just controller_id
logic, move the "IMX7D" case label instead of removing it entirely.] Signed-off-by: Ryan Matthews <ryanmatthews@fastmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84f7 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up") Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch addresses a data corruption issue observed in nvme-tcp during
testing.
In an NVMe native multipath setup, when an I/O timeout occurs, all
inflight I/Os are canceled almost immediately after the kernel socket is
shut down. These canceled I/Os are reported as host path errors,
triggering a failover that succeeds on a different path.
However, at this point, the original I/O may still be outstanding in the
host's network transmission path (e.g., the NIC’s TX queue). From the
user-space app's perspective, the buffer associated with the I/O is
considered completed since they're acked on the different path and may
be reused for new I/O requests.
Because nvme-tcp enables zero-copy by default in the transmission path,
this can lead to corrupted data being sent to the original target,
ultimately causing data corruption.
We can reproduce this data corruption by injecting delay on one path and
triggering i/o timeout.
To prevent this issue, this change ensures that all inflight
transmissions are fully completed from host's perspective before
returning from queue stop. To handle concurrent I/O timeout from multiple
namespaces under the same controller, always wait in queue stop
regardless of queue's state.
This aligns with the behavior of queue stopping in other NVMe fabric
transports.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver") Signed-off-by: Michael Liang <mliang@purestorage.com> Reviewed-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reviewed-by: Randy Jennings <randyj@purestorage.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
For version 1 register dump that includes the PCIe stats, the existing
code incorrectly assumes that all PCIe stats are 64-bit values. Fix it
by using an array containing the starting and ending index of the 32-bit
values. The loop in bnxt_get_regs() will use the array to do proper
endian swap for the 32-bit values.
Fixes: b5d600b027eb ("bnxt_en: Add support for 'ethtool -d'") Reviewed-by: Shruti Parab <shruti.parab@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus psrom,
as 16-bit little-endian values.
However, the integer fields of t_SROM are host byte order integers.
And in the case of led_mode this leads to a little endian value
being incorrectly treated as host byte order.
Looking at rio_set_led_mode, this does appear to be a bug as that code
masks led_mode with 0x1, 0x2 and 0x8. Logic that would be effected by a
reversed byte order.
This problem would only manifest on big endian hosts.
Found by inspection while investigating a sparse warning
regarding the crc field of t_SROM.
I believe that warning is a false positive. And although I plan
to send a follow-up to use little-endian types for other the integer
fields of PSROM_t I do not believe that will involve any bug fixes.
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of qfq, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
This patch checks whether the class was already added to the agg->active
list (cl_is_active) before doing the addition to cater for the reentrant
case.
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of ets, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether
the class was already added to the active_list (cl_is_active) before
doing the addition to cater for the reentrant case.
As described in Gerrard's report [1], we have a UAF case when an hfsc class
has a netem child qdisc. The crux of the issue is that hfsc is assuming
that checking for cl->qdisc->q.qlen == 0 guarantees that it hasn't inserted
the class in the vttree or eltree (which is not true for the netem
duplicate case).
This patch checks the n_active class variable to make sure that the code
won't insert the class in the vttree or eltree twice, catering for the
reentrant case.
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of drr, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether the
class was already added to the active_list (cl_is_active) before adding
to the list to cover for the reentrant case.
The cited commit assumes enabling roce always succeeds. But it is
not true. Add error handling for it.
Fixes: 80f09dfc237f ("net/mlx5: Eswitch, enable RoCE loopback traffic") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/20250423083611.324567-6-mbloch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize the source MAC address when creating the default GID entry.
Since this entry is used only for loopback traffic, it only needs to
be a unicast address. A zeroed-out MAC address is sufficient for this
purpose.
Without this fix, random bits would be assigned as the source address.
If these bits formed a multicast address, the firmware would return an
error, preventing the user from switching to switchdev mode:
If we're redirecting the skb, and haven't called tcf_mirred_forward(),
yet, we need to tell the core to drop the skb by setting the retcode
to SHOT. If we have called tcf_mirred_forward(), however, the skb
is out of our hands and returning SHOT will lead to UaF.
Move the retval override to the error path which actually need it.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Fixes: e5cf1baf92cb ("act_mirred: use TC_ACT_REINSERT when possible") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[Minor conflict resolved due to code context change.] Signed-off-by: Jianqi Ren <jianqi.ren.cn@windriver.com> Signed-off-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported this bug:
==================================================================
BUG: KASAN: slab-out-of-bounds in trace_seq_to_buffer kernel/trace/trace.c:1830 [inline]
BUG: KASAN: slab-out-of-bounds in tracing_splice_read_pipe+0x6be/0xdd0 kernel/trace/trace.c:6822
Write of size 4507 at addr ffff888032b6b000 by task syz.2.320/7260
It has been reported that trace_seq_to_buffer() tries to copy more data
than PAGE_SIZE to buf. Therefore, to prevent this, we should use the
smaller of trace_seq_used(&iter->seq) and PAGE_SIZE as an argument.
Link: https://lore.kernel.org/20250422113026.13308-1-aha310510@gmail.com Reported-by: syzbot+c8cd2d2c412b868263fb@syzkaller.appspotmail.com Fixes: 3c56819b14b0 ("tracing: splice support for tracing_pipe") Suggested-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Jeongjun Park <aha310510@gmail.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Lenovo ThinkPad X201, when Intel VT-d is enabled in the BIOS, the
kernel boots with errors related to DMAR, the graphical interface appeared
quite choppy, and the system resets erratically within a minute after it
booted:
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write NO_PASID] Request device [00:02.0] fault addr 0xb97ff000
[fault reason 0x05] PTE Write access is not set
Upon comparing boot logs with VT-d on/off, I found that the Intel Calpella
quirk (`quirk_calpella_no_shadow_gtt()') correctly applied the igfx IOMMU
disable/quirk correctly:
pci 0000:00:00.0: DMAR: BIOS has allocated no shadow GTT; disabling IOMMU
for graphics
Whereas with VT-d on, it went into the "else" branch, which then
triggered the DMAR handling fault above:
... else if (!disable_igfx_iommu) {
/* we have to ensure the gfx device is idle before we flush */
pci_info(dev, "Disabling batched IOTLB flush on Ironlake\n");
iommu_set_dma_strict();
}
Now, this is not exactly scientific, but moving 0x0044 to quirk_iommu_igfx
seems to have fixed the aforementioned issue. Running a few `git blame'
runs on the function, I have found that the quirk was originally
introduced as a fix specific to ThinkPad X201:
commit 9eecabcb9a92 ("intel-iommu: Abort IOMMU setup for igfx if BIOS gave
no shadow GTT space")
Which was later revised twice to the "else" branch we saw above:
- 2011: commit 6fbcfb3e467a ("intel-iommu: Workaround IOTLB hang on
Ironlake GPU")
- 2024: commit ba00196ca41c ("iommu/vt-d: Decouple igfx_off from graphic
identity mapping")
I'm uncertain whether further testings on this particular laptops were
done in 2011 and (honestly I'm not sure) 2024, but I would be happy to do
some distro-specific testing if that's what would be required to verify
this patch.
P.S., I also see IDs 0x0040, 0x0062, and 0x006a listed under the same
`quirk_calpella_no_shadow_gtt()' quirk, but I'm not sure how similar these
chipsets are (if they share the same issue with VT-d or even, indeed, if
this issue is specific to a bug in the Lenovo BIOS). With regards to
0x0062, it seems to be a Centrino wireless card, but not a chipset?
I have also listed a couple (distro and kernel) bug reports below as
references (some of them are from 7-8 years ago!), as they seem to be
similar issue found on different Westmere/Ironlake, Haswell, and Broadwell
hardware setups.
There is a string parsing logic error which can lead to an overflow of hid
or uid buffers. Comparing ACPIID_LEN against a total string length doesn't
take into account the lengths of individual hid and uid buffers so the
check is insufficient in some cases. For example if the length of hid
string is 4 and the length of the uid string is 260, the length of str
will be equal to ACPIID_LEN + 1 but uid string will overflow uid buffer
which size is 256.
The same applies to the hid string with length 13 and uid string with
length 250.
Check the length of hid and uid strings separately to prevent
buffer overflow.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
realloc_argv() was only updating the array size if it was called with
old_argv already allocated. The first time it was called to create an
argv array, it would allocate the array but return the array size as
zero. dm_split_args() would think that it couldn't store any arguments
in the array and would call realloc_argv() again, causing it to
reallocate the initial slots (this time using GPF_KERNEL) and finally
return a size. Aside from being wasteful, this could cause deadlocks on
targets that need to process messages without starting new IO. Instead,
realloc_argv should always update the allocated array size on success.
Fixes: a0651926553c ("dm table: don't copy from a NULL pointer in realloc_argv()") Cc: stable@vger.kernel.org Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function brcmf_usb_dl_writeimage() calls the function
brcmf_usb_dl_cmd() but dose not check its return value. The
'state.state' and the 'state.bytes' are uninitialized if the
function brcmf_usb_dl_cmd() fails. It is dangerous to use
uninitialized variables in the conditions.
Add error handling for brcmf_usb_dl_cmd() to jump to error
handling path if the brcmf_usb_dl_cmd() fails and the
'state.state' and the 'state.bytes' are uninitialized.
Improve the error message to report more detailed error
information.
Fixes: 71bb244ba2fd ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Link: https://patch.msgid.link/20250422042203.2259-1-vulab@iscas.ac.cn Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the XGMAC specification, enabling features such as Layer 3
and Layer 4 Packet Filtering, Split Header and Virtualized Network support
automatically selects the IPC Full Checksum Offload Engine on the receive
side.
When RX checksum offload is disabled, these dependent features must also
be disabled to prevent abnormal behavior caused by mismatched feature
dependencies.
Ensure that toggling RX checksum offload (disabling or enabling) properly
disables or enables all dependent features, maintaining consistent and
expected behavior in the network device.
Cc: stable@vger.kernel.org Fixes: 1a510ccf5869 ("amd-xgbe: Add support for VXLAN offload capabilities") Signed-off-by: Vishal Badole <Vishal.Badole@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250424130248.428865-1-Vishal.Badole@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Camm noticed that on parisc a SIGFPE exception will crash an application with
a second SIGFPE in the signal handler. Dave analyzed it, and it happens
because glibc uses a double-word floating-point store to atomically update
function descriptors. As a result of lazy binding, we hit a floating-point
store in fpe_func almost immediately.
When the T bit is set, an assist exception trap occurs when when the
co-processor encounters *any* floating-point instruction except for a double
store of register %fr0. The latter cancels all pending traps. Let's fix this
by clearing the Trap (T) bit in the FP status register before returning to the
signal handler in userspace.
The issue can be reproduced with this test program:
Deferred probe with pm_runtime_put() may delay clock disable, causing
incorrect clock usage count. Use pm_runtime_put_sync() to ensure the
clock is disabled immediately.
Fixes: 13d6eb20fc79 ("i2c: imx-lpi2c: add runtime pm support") Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Carlos Song <carlos.song@nxp.com> Cc: <stable@vger.kernel.org> # v4.16+ Link: https://lore.kernel.org/r/20250421062341.2471922-1-carlos.song@nxp.com Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nouveau is mostly designed in a way that it's expected that fences only
ever get signaled through nouveau_fence_signal(). However, in at least
one other place, nouveau_fence_done(), can signal fences, too. If that
happens (race) a signaled fence remains in the pending list for a while,
until it gets removed by nouveau_fence_update().
Should nouveau_fence_context_kill() run in the meantime, this would be
a bug because the function would attempt to set an error code on an
already signaled fence.
Have nouveau_fence_context_kill() check for a fence being signaled.
Cc: stable@vger.kernel.org # v5.10+ Fixes: ea13e5abf807 ("drm/nouveau: signal pending fences when channel has been killed") Suggested-by: Christian König <christian.koenig@amd.com> Signed-off-by: Philipp Stanner <phasta@kernel.org> Link: https://lore.kernel.org/r/20250415121900.55719-3-phasta@kernel.org Signed-off-by: Danilo Krummrich <dakr@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
