On beagleboard revisions A to B4 we need to use gpt12 as the system timer.
However, the quirk handling added for gpt12 caused a regression for system
suspend for am335x as the PM coprocessor needs the timers idled for
suspend.
Let's make the gpt12 quirk specific to omap34xx, other SoCs don't need
it. Beagleboard revisions C and later no longer need to use the gpt12
related quirk. Then at some point, if we decide to drop support for the old
beagleboard revisions A to B4, we can also drop the gpt12 related quirks
completely.
Fixes: 3ff340e24c9d ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status") Reported-by: Kevin Hilman <khilman@baylibre.com> Suggested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: fd1c07861491 ("ARM: OMAP4: Fix the init code to have OMAP4460 errata available in DT build") Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220309104302.18398-1-linmq006@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae5a ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM") Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.
It will cause driver to not update ERDP to hardware,
Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.
Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.
[commit message rewording -Mathias]
Fixes: dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer on purpose") Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
Amlogic SM1 devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: 3d9e76483049 ("arm64: dts: meson-sm1-sei610: enable DVFS") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220210100638.19130-3-christianshewitt@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Amlogic G12B devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b96d4e92709b ("arm64: dts: meson-g12b: support a311d and s922x cpu operating points") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220210100638.19130-2-christianshewitt@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When an iocg is in debt, its inuse weight is owned by debt handling and
should stay at 1. This invariant was broken when determining the amount of
surpluses at the beginning of donation calculation - when an iocg's
hierarchical weight is too low, the iocg is excluded from donation
calculation and its inuse is reset to its active regardless of its
indebtedness, triggering warnings like the following:
As this happens only when an iocg's hierarchical weight is negligible, its
impact likely is limited to triggering the warnings. Fix it by skipping
resetting inuse of under-weighted debtors.
When a XEN_HVM guest uses the XEN PIRQ/Eventchannel mechanism, then
PCI/MSI[-X] masking is solely controlled by the hypervisor, but contrary to
XEN_PV guests this does not disable PCI/MSI[-X] masking in the PCI/MSI
layer.
This can lead to a situation where the PCI/MSI layer masks an MSI[-X]
interrupt and the hypervisor grants the write despite the fact that it
already requested the interrupt. As a consequence interrupt delivery on the
affected device is not happening ever.
Set pci_msi_ignore_mask to prevent that like it's done for XEN_PV guests
already.
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
If we pass too short string to "hex2bin" (and the string size without
the terminating NUL character is even), "hex2bin" reads one byte after
the terminating NUL character. This patch fixes it.
Note that hex_to_bin returns -1 on error and hex2bin return -EINVAL on
error - so we can't just return the variable "hi" or "lo" on error.
This inconsistency may be fixed in the next merge window, but for the
purpose of fixing this bug, we just preserve the existing behavior and
return -1 and -EINVAL.
The function hex2bin is used to load cryptographic keys into device
mapper targets dm-crypt and dm-integrity. It should take constant time
independent on the processed data, so that concurrently running
unprivileged code can't infer any information about the keys via
microarchitectural convert channels.
This patch changes the function hex_to_bin so that it contains no
branches and no memory accesses.
Note that this shouldn't cause performance degradation because the size
of the new function is the same as the size of the old function (on
x86-64) - and the new function causes no branch misprediction penalties.
I compile-tested this function with gcc on aarch64 alpha arm hppa hppa64
i386 ia64 m68k mips32 mips64 powerpc powerpc64 riscv sh4 s390x sparc32
sparc64 x86_64 and with clang on aarch64 arm hexagon i386 mips32 mips64
powerpc powerpc64 s390x sparc32 sparc64 x86_64 to verify that there are
no branches in the generated code.
The Samsung pinctrl drivers depend on OF_GPIO, which is part of GPIOLIB.
ARMv7 Exynos platform selects GPIOLIB and Samsung pinctrl drivers. ARMv8
Exynos selects only the latter leading to possible wrong configuration
on ARMv8 build:
WARNING: unmet direct dependencies detected for PINCTRL_EXYNOS
Depends on [n]: PINCTRL [=y] && OF_GPIO [=n] && (ARCH_EXYNOS [=y] || ARCH_S5PV210 || COMPILE_TEST [=y])
Selected by [y]:
- ARCH_EXYNOS [=y]
Always select the GPIOLIB from the Samsung pinctrl drivers to fix the
issue. This requires removing of OF_GPIO dependency (to avoid recursive
dependency), so add dependency on OF for COMPILE_TEST cases.
Reported-by: Necip Fazil Yildiran <fazilyildiran@gmail.com> Fixes: eed6b3eb20b9 ("arm64: Split out platform options to separate Kconfig") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20220420141407.470955-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of 3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable <stable@kernel.org> Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend") Cc: stable@vger.kernel.org # v4.0+ Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da92f
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c18 ("serial: imx: ensure that RX irqs are off if RX is off") Cc: stable@vger.kernel.org # 4.17 Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Path fixes bug which occurs during resetting endpoint in
__cdns3_gadget_ep_clear_halt function. During resetting endpoint
controller will change HW/DMA owned TRB. It set Abort flag in
trb->control and will change trb->length field. If driver want
to use the aborted trb it must update the changed field in
TRB.
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Make sure not to set run_stop bit or link state change request while
initiating soft-reset. Register read-modify-write operation may
unintentionally start the controller before the initialization completes
with its previous DCTL value, which can cause initialization failure.
The current driver logic checks against 0 to determine whether the
periodic tx/rx threshold settings are set, but we may get bogus values
from uninitialized variables if no device property is set. Properly
default these variables to 0.
If the PHY controller node has a "port" dwc3 tries to find an
extcon device even when "usb-role-switch" is present. This happens
because dwc3_get_extcon() sees that "port" node and then calls
extcon_find_edev_by_node() which will always return EPROBE_DEFER
in that case.
On the other hand, even if an extcon was present and dwc3_get_extcon()
was successful it would still be ignored in favor of "usb-role-switch".
Let's just first check if "usb-role-switch" is configured in the device
tree and directly use it instead and only try to look for an extcon
device otherwise.
Fixes: 8a0a13799744 ("usb: dwc3: Registering a role switch in the DRD code.") Cc: stable <stable@kernel.org> Signed-off-by: Sven Peter <sven@svenpeter.dev> Link: https://lore.kernel.org/r/20220411155300.9766-1-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
During the uvcg_video_pump() process, if an error occurs and
uvcg_queue_cancel() is called, the buffer queue will be cleared out, but
the current marker (queue->buf_used) of the active buffer (no longer
active) is not reset. On the next iteration of uvcg_video_pump() the
stale buf_used count will be used and the logic of min((unsigned
int)len, buf->bytesused - queue->buf_used) may incorrectly calculate a
nbytes size, causing an invalid memory access.
[80802.185460][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
[80802.185519][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
...
uvcg_queue_cancel() is called and the queue is cleared out, but the
marker queue->buf_used is not reset.
...
[80802.262328][ T8682] Unable to handle kernel paging request at virtual
address ffffffc03af9f000
...
...
[80802.263138][ T8682] Call trace:
[80802.263146][ T8682] __memcpy+0x12c/0x180
[80802.263155][ T8682] uvcg_video_pump+0xcc/0x1e0
[80802.263165][ T8682] process_one_work+0x2cc/0x568
[80802.263173][ T8682] worker_thread+0x28c/0x518
[80802.263181][ T8682] kthread+0x160/0x170
[80802.263188][ T8682] ret_from_fork+0x10/0x18
[80802.263198][ T8682] Code: a8c12829a88130cb a8c130
Fixes: d692522577c0 ("usb: gadget/uvc: Port UVC webcam gadget to use videobuf2 framework") Cc: <stable@vger.kernel.org> Signed-off-by: Dan Vacura <w36195@motorola.com> Link: https://lore.kernel.org/r/20220331184024.23918-1-w36195@motorola.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All attempts to swap the roles timed out because the
completion was done without releasing the port lock. Fixing
that by releasing the lock before starting to wait for the
completion.
The role swapping completion variable is reused, so it needs
to be reinitialised every time. Otherwise it will be marked
as done after the first time it's used and completing
immediately.
usb_put_dev shouldn't be called when uss720_probe succeeds because of
priv->usbdev. At the same time, priv->usbdev shouldn't be set to NULL
before destroy_priv in uss720_disconnect because usb_put_dev is in
destroy_priv.
Fix this by moving priv->usbdev = NULL after usb_put_dev.
This register write to REG_INTF_CONFIG6 enables a spike filter that
is impacting the line and can prevent the I2C ACK to be seen by the
controller. So we don't test the return value.
The first U3 wake signal by the host may be lost if the USB 3 connection is
tunneled over USB4, with a runtime suspended USB4 host, and firmware
implemented connection manager.
Specs state the host must wait 100ms (tU3WakeupRetryDelay) before
resending a U3 wake signal if device doesn't respond, leading to U3 -> U0
link transition times around 270ms in the tunneled case.
Fixes: 0200b9f790b0 ("xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220408134823.2527272-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Alderlake has two XHCI controllers with PCI IDs 0x461e and 0x51ed. We
had previously added the quirk to default enable runtime PM for 0x461e,
now add it for 0x51ed as well.
The result is technically harmless, as both the source and the
destinations are currently the same allocation size (4 bytes) and don't
use their padding, but if anything were to ever be added after the
"mcr" member in "struct whiteheat_private", it would be overwritten. The
structs both have a single u8 "mcr" member, but are 4 bytes in padded
size. The memcpy() destination was explicitly targeting the u8 member
(size 1) with the length of the whole structure (size 4), triggering
the memcpy buffer overflow warning:
In file included from include/linux/string.h:253,
from include/linux/bitmap.h:11,
from include/linux/cpumask.h:12,
from include/linux/smp.h:13,
from include/linux/lockdep.h:14,
from include/linux/spinlock.h:62,
from include/linux/mmzone.h:8,
from include/linux/gfp.h:6,
from include/linux/slab.h:15,
from drivers/usb/serial/whiteheat.c:17:
In function 'fortify_memcpy_chk',
inlined from 'firm_send_command' at drivers/usb/serial/whiteheat.c:587:4:
include/linux/fortify-string.h:328:25: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
328 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Issue description:
When an OTG port has been switched to device role and then switch back
to host role again, the USB 3.0 Host (XHCI) will not be able to detect
"plug in event of a connected USB 2.0/1.0 ((Highspeed and Fullspeed)
devices until system reboot.
Root cause and Solution:
There is a condition checking flag "ssusb->otg_switch.is_u3_drd" in
toggle_opstate(). At the end of role switch procedure, toggle_opstate()
will be called to set DC_SESSION and SOFT_CONN bit. If "is_u3_drd" was
set and switched the role to USB host 3.0, bit DC_SESSION and SOFT_CONN
will be skipped hence caused the port cannot detect connected USB 2.0
(Highspeed and Fullspeed) devices. Simply remove the condition check to
solve this issue.
In commit 9ea9b9c48387 ("remove the lightnvm subsystem") the lightnvm
subsystem was removed as there is no hardware in the wild for it, and
the code is known to have problems. This should also be disabled for
older LTS kernels as well to prevent anyone from accidentally using it.
Cc: Christoph Hellwig <hch@lst.de> Cc: Matias Bjørling <mb@lightnvm.io> Cc: Javier González <javier@javigon.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minh Yuan reported a concurrency use-after-free issue in the floppy code
between raw_cmd_ioctl and seek_interrupt.
[ It turns out this has been around, and that others have reported the
KASAN splats over the years, but Minh Yuan had a reproducer for it and
so gets primary credit for reporting it for this fix - Linus ]
The problem is, this driver tends to break very easily and nowadays,
nobody is expected to use FDRAWCMD anyway since it was used to
manipulate non-standard formats. The risk of breaking the driver is
higher than the risk presented by this race, and accessing the device
requires privileges anyway.
Let's just add a config option to completely disable this ioctl and
leave it disabled by default. Distros shouldn't use it, and only those
running on antique hardware might need to enable it.
The upstream commit c3efcedd272a ("net: micrel: fix KS8851_MLL Kconfig")
depends on e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies")
which is not part of Linux 5.10.y . Revert the aforementioned commit to
prevent breakage in 5.10.y .
Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Sasha Levin <sashal@kernel.org> Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supply additional check in order to prevent unexpected results.
Fixes: b892bf75b2034 ("ion: Switch ion to use dma-buf") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Above issue may happen as follows:
write truncate kjournald2
generic_perform_write
ext4_write_begin
ext4_walk_page_buffers
do_journal_get_write_access ->add BJ_Reserved list
ext4_journalled_write_end
ext4_walk_page_buffers
write_end_fn
ext4_handle_dirty_metadata
***************JBD2 ABORT**************
jbd2_journal_dirty_metadata
-> return -EROFS, jh in reserved_list
jbd2_journal_commit_transaction
while (commit_transaction->t_reserved_list)
jh = commit_transaction->t_reserved_list;
truncate_pagecache_range
do_invalidatepage
ext4_journalled_invalidatepage
jbd2_journal_invalidatepage
journal_unmap_buffer
__dispose_buffer
__jbd2_journal_unfile_buffer
jbd2_journal_put_journal_head ->put last ref_count
__journal_remove_journal_head
bh->b_private = NULL;
jh->b_bh = NULL;
jbd2_journal_refile_buffer(journal, jh);
bh = jh2bh(jh);
->bh is NULL, later will trigger null-ptr-deref
journal_free_journal_head(jh);
After commit 96f1e0974575, we no longer hold the j_state_lock while
iterating over the list of reserved handles in
jbd2_journal_commit_transaction(). This potentially allows the
journal_head to be freed by journal_unmap_buffer while the commit
codepath is also trying to free the BJ_Reserved buffers. Keeping
j_state_lock held while trying extends hold time of the lock
minimally, and solves this issue.
Fixes: 96f1e0974575("jbd2: avoid long hold times of j_state_lock while committing a transaction") Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220317142137.1821590-1-yebin10@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first attempt to fix a the 'impossible' WARN_ON_ONCE(1) in
isotp_tx_timer_handler() focussed on the identical CAN IDs created by
the syzbot reproducer and lead to upstream fix/commit 3ea566422cbd
("can: isotp: sanitize CAN ID checks in isotp_bind()"). But this did
not catch the root cause of the wrong tx.state in the tx_timer handler.
In the isotp 'first frame' case a timeout monitoring needs to be started
before the 'first frame' is send. But when this sending failed the timeout
monitoring for this specific frame has to be disabled too.
Otherwise the tx_timer is fired with the 'warn me' tx.state of ISOTP_IDLE.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/20220405175112.2682-1-socketcan@hartkopp.net Reported-by: syzbot+2339c27f5c66c652843e@syzkaller.appspotmail.com Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the file system does not use bigalloc, calculating the overhead is
cheap, so force the recalculation of the overhead so we don't have to
trust the precalculated overhead in the superblock.
The kernel calculation was underestimating the overhead by not taking
into account the reserved gdt blocks. With this change, the overhead
calculated by the kernel matches the overhead calculation in mke2fs.
Syzbot found an issue [1] in ext4_fallocate().
The C reproducer [2] calls fallocate(), passing size 0xffeffeff000ul,
and offset 0x1000000ul, which, when added together exceed the
bitmap_maxbytes for the inode. This triggers a BUG in
ext4_ind_remove_space(). According to the comments in this function
the 'end' parameter needs to be one block after the last block to be
removed. In the case when the BUG is triggered it points to the last
block. Modify the ext4_punch_hole() function and add constraint that
caps the length to satisfy the one before laster block requirement.
We got issue as follows:
EXT4-fs (loop0): mounted filesystem without journal. Opts: ,errors=continue
==================================================================
BUG: KASAN: use-after-free in ext4_search_dir fs/ext4/namei.c:1394 [inline]
BUG: KASAN: use-after-free in search_dirblock fs/ext4/namei.c:1199 [inline]
BUG: KASAN: use-after-free in __ext4_find_entry+0xdca/0x1210 fs/ext4/namei.c:1553
Read of size 1 at addr ffff8881317c3005 by task syz-executor117/2331
If read 'de->name_len' which address is 0xffff8881317c3005, obviously is
out of range, then will trigger use-after-free.
To solve this issue, 'dlimit' must reserve 8 bytes, as we will read
'de->name_len' to judge if '(char *) de + de->name_len' out of range.
Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220324064816.1209985-1-yebin10@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We got issue as follows:
[home]# fsck.ext4 -fn ram0yb
e2fsck 1.45.6 (20-Mar-2020)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Symlink /p3/d14/d1a/l3d (inode #3494) is invalid.
Clear? no
Entry 'l3d' in /p3/d14/d1a (3383) has an incorrect filetype (was 7, should be 0).
Fix? no
As the symlink file size does not match the file content. If the writeback
of the symlink data block failed, ext4_finish_bio() handles the end of IO.
However this function fails to mark the buffer with BH_write_io_error and
so when unmount does journal checkpoint it cannot detect the writeback
error and will cleanup the journal. Thus we've lost the correct data in the
journal area. To solve this issue, mark the buffer as BH_write_io_error in
ext4_finish_bio().
Cc: stable@kernel.org Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220321144438.201685-1-yebin10@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the initial introduction of (posix) fallocate back at the turn of
the century, it has been possible to use this syscall to change the
user-visible contents of files. This can happen by extending the file
size during a preallocation, or through any of the newer modes (punch,
zero, collapse, insert range). Because the call can be used to change
file contents, we should treat it like we do any other modification to a
file -- update the mtime, and drop set[ug]id privileges/capabilities.
The VFS function file_modified() does all this for us if pass it a
locked inode, so let's make fallocate drop permissions correctly.
Signed-off-by: Darrick J. Wong <djwong@kernel.org> Link: https://lore.kernel.org/r/20220308185043.GA117678@magnolia Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit bb30acae4c4dacfa ("perf report: Bail out --mem-mode if mem
info is not available") "perf mem report" and "perf report --mem-mode"
don't report result if the PERF_SAMPLE_DATA_SRC bit is missed in sample
type.
The commit ffab487052054162 ("perf: arm-spe: Fix perf report
--mem-mode") partially fixes the issue. It adds PERF_SAMPLE_DATA_SRC
bit for Arm SPE event, this allows the perf data file generated by
kernel v5.18-rc1 or later version can be reported properly.
On the other hand, perf tool still fails to be backward compatibility
for a data file recorded by an older version's perf which contains Arm
SPE trace data. This patch is a workaround in reporting phase, when
detects ARM SPE PMU event and without PERF_SAMPLE_DATA_SRC bit, it will
force to set the bit in the sample type and give a warning info.
Fixes: bb30acae4c4dacfa ("perf report: Bail out --mem-mode if mem info is not available") Reviewed-by: James Clark <james.clark@arm.com> Signed-off-by: Leo Yan <leo.yan@linaro.org> Tested-by: German Gomez <german.gomez@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Link: https://lore.kernel.org/r/20220414123201.842754-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When scheduling a group of events, there are constraint checks done to
make sure all events can go in a group. Example, one of the criteria is
that events in a group cannot use the same PMC. But platform specific
PMU supports alternative event for some of the event codes. During
perf_event_open(), if any event group doesn't match constraint check
criteria, further lookup is done to find alternative event.
By current design, the array of alternatives events in PMU code is
expected to be sorted by column 0. This is because in
find_alternative() the return criteria is based on event code
comparison. ie. "event < ev_alt[i][0])". This optimisation is there
since find_alternative() can be called multiple times. In power9 PMU
code, the alternative event array is not sorted properly and hence there
is breakage in finding alternative events.
To work with existing logic, fix the alternative event array to be
sorted by column 0 for power9-pmu.c
Results:
With alternative events, multiplexing can be avoided. That is, for
example, in power9 PM_LD_MISS_L1 (0x3e054) has alternative event,
PM_LD_MISS_L1_ALT (0x400f0). This is an identical event which can be
programmed in a different PMC.
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1.
Also, we need to call pm_runtime_put_noidle() when pm_runtime_get_sync()
fails, so use pm_runtime_resume_and_get() instead. this function
will handle this.
The LoPAPR spec defines a guest visible IOMMU with a variable page size.
Currently QEMU advertises 4K, 64K, 2M, 16MB pages, a Linux VM picks
the biggest (16MB). In the case of a passed though PCI device, there is
a hardware IOMMU which does not support all pages sizes from the above -
P8 cannot do 2MB and P9 cannot do 16MB. So for each emulated
16M IOMMU page we may create several smaller mappings ("TCEs") in
the hardware IOMMU.
The code wrongly uses the emulated TCE index instead of hardware TCE
index in error handling. The problem is easier to see on POWER8 with
multi-level TCE tables (when only the first level is preallocated)
as hash mode uses real mode TCE hypercalls handlers.
The kernel starts using indirect tables when VMs get bigger than 128GB
(depends on the max page order).
The very first real mode hcall is going to fail with H_TOO_HARD as
in the real mode we cannot allocate memory for TCEs (we can in the virtual
mode) but on the way out the code attempts to clear hardware TCEs using
emulated TCE indexes which corrupts random kernel memory because
it_offset==1<<59 is subtracted from those indexes and the resulting index
is out of the TCE table bounds.
This fixes kvmppc_clear_tce() to use the correct TCE indexes.
While at it, this fixes TCE cache invalidation which uses emulated TCE
indexes instead of the hardware ones. This went unnoticed as 64bit DMA
is used these days and VMs map all RAM in one go and only then do DMA
and this is when the TCE cache gets populated.
Potentially this could slow down mapping, however normally 16MB
emulated pages are backed by 64K hardware pages so it is one write to
the "TCE Kill" per 256 updates which is not that bad considering the size
of the cache (1024 TCEs or so).
The panel has a prepare call which is before video starts, and an
enable call which is after.
The Toshiba bridge should be configured before video, so move
the relevant power and initialisation calls to prepare.
Fixes: 2f733d6194bd ("drm/panel: Add support for the Raspberry Pi 7" Touchscreen.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220415162513.42190-3-stefan.wahren@i2se.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If a call to rpi_touchscreen_i2c_write from rpi_touchscreen_probe
fails before mipi_dsi_device_register_full is called, then
in trying to log the error message if uses ts->dsi->dev when
it is still NULL.
Use ts->i2c->dev instead, which is initialised earlier in probe.
Fixes: 2f733d6194bd ("drm/panel: Add support for the Raspberry Pi 7" Touchscreen.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220415162513.42190-2-stefan.wahren@i2se.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This problem can be reproduced with CONFIG_PERF_USE_VMALLOC enabled on
both x86_64 and aarch64 arch when using sysdig -B(using ebpf)[1].
sysdig -B works fine after rebuilding the kernel with
CONFIG_PERF_USE_VMALLOC disabled.
I tracked it down to the if condition event->rb->nr_pages != nr_pages
in perf_mmap is true when CONFIG_PERF_USE_VMALLOC is enabled where
event->rb->nr_pages = 1 and nr_pages = 2048 resulting perf_mmap to
return -EINVAL. This is because when CONFIG_PERF_USE_VMALLOC is
enabled, rb->nr_pages is always equal to 1.
Arch with CONFIG_PERF_USE_VMALLOC enabled by default:
arc/arm/csky/mips/sh/sparc/xtensa
Arch with CONFIG_PERF_USE_VMALLOC disabled by default:
x86_64/aarch64/...
Fix this problem by using data_page_nr()
[1] https://github.com/draios/sysdig
Fixes: 906010b2134e ("perf_event: Provide vmalloc() based mmap() backing") Signed-off-by: Zhipeng Xie <xiezhipeng1@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20220209145417.6495-1-xiezhipeng1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There exists a corner case in attach_entity_load_avg() which will
cause load_sum to be zero while load_avg will not be.
Consider se_weight is 88761 as per the sched_prio_to_weight[] table.
Further assume the get_pelt_divider() is 47742, this gives:
se->avg.load_avg is 1.
In the case where there is only a cycle counter available (i.e.
PMCR_EL0.N is 0) and an event other than CPU cycles is opened, the open
should fail as the event can never possibly be scheduled. However, the
event validation when an event is opened is skipped when the group
leader is opened. Fix this by always validating the group leader events.
Reported-by: Al Grant <al.grant@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/r/20220408203330.4014015-1-robh@kernel.org Cc: <stable@vger.kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function syscall_trace_exit expects pointer to pt_regs. However
r0 is also used to keep syscall return value. Restore pointer
to pt_regs before calling syscall_trace_exit.
These two bug are here:
list_for_each_entry_safe_continue(w, n, list,
power_list);
list_for_each_entry_safe_continue(w, n, list,
power_list);
After the list_for_each_entry_safe_continue() exits, the list iterator
will always be a bogus pointer which point to an invalid struct objdect
containing HEAD member. The funciton poniter 'w->event' will be a
invalid value which can lead to a control-flow hijack if the 'w' can be
controlled.
The original intention was to continue the outer list_for_each_entry_safe()
loop with the same entry if w->event is NULL, but misunderstanding the
meaning of list_for_each_entry_safe_continue().
So just add a 'continue;' to fix the bug.
Cc: stable@vger.kernel.org Fixes: 163cac061c973 ("ASoC: Factor out DAPM sequence execution") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Link: https://lore.kernel.org/r/20220329012134.9375-1-xiam0nd.tong@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members
before initialization") attempted to fix a race condition that lead to a
NULL pointer, but in the process caused a regression for _AEI/_EVT
declared GPIOs.
This manifests in messages showing deferred probing while trying to
allocate IRQs like so:
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x002C to IRQ, err -517
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x003D to IRQ, err -517
[ .. more of the same .. ]
The code for walking _AEI doesn't handle deferred probing and so this
leads to non-functional GPIO interrupts.
Fix this issue by moving the call to `acpi_gpiochip_request_interrupts`
to occur after gc->irc.initialized is set.
Given a sufficiently large number of actions, while copying and
reserving memory for a new action of a new flow, if next_offset is
greater than MAX_ACTIONS_BUFSIZE, the function reserve_sfa_size() does
not return -EMSGSIZE as expected, but it allocates MAX_ACTIONS_BUFSIZE
bytes increasing actions_len by req_size. This can then lead to an OOB
write access, especially when further actions need to be copied.
Fix it by rearranging the flow action size check.
KASAN splat below:
==================================================================
BUG: KASAN: slab-out-of-bounds in reserve_sfa_size+0x1ba/0x380 [openvswitch]
Write of size 65360 at addr ffff888147e4001c by task handler15/836
Fast coprocessor exception handler saves a3..a6, but coprocessor context
load/store code uses a4..a7 as temporaries, potentially clobbering a7.
'Potentially' because coprocessor state load/store macros may not use
all four temporary registers (and neither FPU nor HiFi macros do).
Use a3..a6 as intended.
Cc: stable@vger.kernel.org Fixes: c658eac628aa ("[XTENSA] Add support for configurable registers and coprocessors") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
This will reset deeply on freeze and thaw instead of suspend and
resume and prevent null pointer dereferences of the uninitialized ring
0 buffer while thawing.
The impact is an indefinitely hanging kernel. You can't switch
consoles after this and the only possible user interaction is SysRq.
The bug has been present since the introduction of the new pm code in 8aaa112a57c1 ("net: atlantic: refactoring pm logic") and was hidden
until 8ce84271697a ("net: atlantic: changes for multi-TC support"),
which refactored the aq_vec_{free,alloc} functions into
aq_vec_{,ring}_{free,alloc}, but is technically not wrong. The
original functions just always reinitialized the buffers on S3/S4. If
the interface is down before freezing, the bug does not occur. It does
not matter, whether the initrd contains and loads the module before
thawing.
So the fix is to invert the boolean parameter deep in all pm function
calls, which was clearly intended to be set like that.
First report was on Github [1], which you have to guess from the
resume logs in the posted dmesg snippet. Recently I posted one on
Bugzilla [2], since I did not have an AQC device so far.
The bug is here:
__func__, desc, &desc->tx_dma_desc.phys, ret, cookie, residue);
The list iterator 'desc' will point to a bogus position containing
HEAD if the list is empty or no element is found. To avoid dev_dbg()
prints a invalid address, use a new variable 'iter' as the list
iterator, while use the origin variable 'desc' as a dedicated
pointer to point to the found element.
Before detecting the cable type on the dma bar, the driver should check
whether the 'bmdma_addr' is zero, which means the adapter does not
support DMA, otherwise we will get the following error:
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases it is possible for mmu_interval_notifier_remove() to race
with mn_tree_inv_end() allowing it to return while the notifier data
structure is still in use. Consider the following sequence:
As the wait_event() condition is true it will return immediately. This
can lead to use-after-free type errors if the caller frees the data
structure containing the interval notifier subscription while it is
still on a deferred list. Fix this by taking the appropriate lock when
reading invalidate_seq to ensure proper synchronisation.
I observed this whilst running stress testing during some development.
You do have to be pretty unlucky, but it leads to the usual problems of
use-after-free (memory corruption, kernel crash, difficult to diagnose
WARN_ON, etc).
Link: https://lkml.kernel.org/r/20220420043734.476348-1-apopple@nvidia.com Fixes: 99cb252f5e68 ("mm/mmu_notifier: add an interval tree notifier") Signed-off-by: Alistair Popple <apopple@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Cc: Christian König <christian.koenig@amd.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pthread struct is allocated on PRIVATE|ANONYMOUS memory [1] which
can be targeted by the oom reaper. This mapping is used to store the
futex robust list head; the kernel does not keep a copy of the robust
list and instead references a userspace address to maintain the
robustness during a process death.
A race can occur between exit_mm and the oom reaper that allows the oom
reaper to free the memory of the futex robust list before the exit path
has handled the futex death:
This is a fix for commit f6795053dac8 ("mm: mmap: Allow for "high"
userspace addresses") for hugetlb.
This patch adds support for "high" userspace addresses that are
optionally supported on the system and have to be requested via a hint
mechanism ("high" addr parameter to mmap).
Architectures such as powerpc and x86 achieve this by making changes to
their architectural versions of hugetlb_get_unmapped_area() function.
However, arm64 uses the generic version of that function.
So take into account arch_get_mmap_base() and arch_get_mmap_end() in
hugetlb_get_unmapped_area(). To allow that, move those two macros out
of mm/mmap.c into include/linux/sched/mm.h
If these macros are not defined in architectural code then they default
to (TASK_SIZE) and (base) so should not introduce any behavioural
changes to architectures that do not define them.
For the time being, only ARM64 is affected by this change.
Catalin (ARM64) said
"We should have fixed hugetlb_get_unmapped_area() as well when we added
support for 52-bit VA. The reason for commit f6795053dac8 was to
prevent normal mmap() from returning addresses above 48-bit by default
as some user-space had hard assumptions about this.
It's a slight ABI change if you do this for hugetlb_get_unmapped_area()
but I doubt anyone would notice. It's more likely that the current
behaviour would cause issues, so I'd rather have them consistent.
Basically when arm64 gained support for 52-bit addresses we did not
want user-space calling mmap() to suddenly get such high addresses,
otherwise we could have inadvertently broken some programs (similar
behaviour to x86 here). Hence we added commit f6795053dac8. But we
missed hugetlbfs which could still get such high mmap() addresses. So
in theory that's a potential regression that should have bee addressed
at the same time as commit f6795053dac8 (and before arm64 enabled
52-bit addresses)"
Qemu unconditionally reports a UUID, which depending on the qemu version
is either all-null (which is incorrect but harmless) or contains a single
bit set for all controllers. In addition it can also optionally report
a eui64 which needs to be manually set. Disable namespace identifiers
for Qemu controlles entirely even if in some cases they could be set
correctly through manual intervention.
Reported-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a quirk to disable using and exporting namespace identifiers for
controllers where they are broken beyond repair.
The most directly visible problem with non-unique namespace identifiers
is that they break the /dev/disk/by-id/ links, with the link for a
supposedly unique identifier now pointing to one of multiple possible
namespaces that share the same ID, and a somewhat random selection of
which one actually shows up.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
struct stat (defined in arch/x86/include/uapi/asm/stat.h) has 32-bit
st_dev and st_rdev; struct compat_stat (defined in
arch/x86/include/asm/compat.h) has 16-bit st_dev and st_rdev followed by
a 16-bit padding.
This patch fixes struct compat_stat to match struct stat.
[ Historical note: the old x86 'struct stat' did have that 16-bit field
that the compat layer had kept around, but it was changes back in 2003
by "struct stat - support larger dev_t":
and back in those days, the x86_64 port was still new, and separate
from the i386 code, and had already picked up the old version with a
16-bit st_dev field ]
Note that we can't change compat_dev_t because it is used by
compat_loop_info.
Also, if the st_dev and st_rdev values are 32-bit, we don't have to use
old_valid_dev to test if the value fits into them. This fixes
-EOVERFLOW on filesystems that are on NVMe because NVMe uses the major
number 259.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Andreas Schwab <schwab@linux-m68k.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We set the qedi_ep state to EP_STATE_OFLDCONN_START when the ep is
created. Then in qedi_set_path we kick off the offload work. If userspace
times out the connection and calls ep_disconnect, qedi will only flush the
offload work if the qedi_ep state has transitioned away from
EP_STATE_OFLDCONN_START. If we can't connect we will not have transitioned
state and will leave the offload work running, and we will free the qedi_ep
from under it.
This patch just has us init the work when we create the ep, then always
flush it.
Link: https://lore.kernel.org/r/20220408001314.5014-10-michael.christie@oracle.com Tested-by: Manish Rangankar <mrangankar@marvell.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Chris Leech <cleech@redhat.com> Acked-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4298388574da ("net: macb: restart tx after tx used bit read")
added support for restarting transmission. Restarting tx does not work
in case controller asserts TXUBR interrupt and TQBP is already at the end
of the tx queue. In that situation, restarting tx will immediately cause
assertion of another TXUBR interrupt. The driver will end up in an infinite
interrupt loop which it cannot break out of.
For cases where TQBP is at the end of the tx queue, instead
only clear TX_USED interrupt. As more data gets pushed to the queue,
transmission will resume.
This issue was observed on a Xilinx Zynq-7000 based board.
During stress test of the network interface,
driver would get stuck on interrupt loop within seconds or minutes
causing CPU to stall.
kzalloc() is a memory allocation function which can return NULL when
some internal memory errors happen. So it is better to check it to
prevent potential wrong memory access.
Besides, since mdp5_plane_reset() is void type, so we should better
set `plane-state` to NULL after releasing it.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/481055/ Link: https://lore.kernel.org/r/tencent_8E2A1C78140EE1784AB2FF4B2088CC0AB908@qq.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function ‘brcmf_sdio_drivestrengthinit’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3798:2: error: case label does not reduce to an integer constant
case SDIOD_DRVSTR_KEY(BRCM_CC_43143_CHIP_ID, 17):
^~~~
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3809:2: error: case label does not reduce to an integer constant
case SDIOD_DRVSTR_KEY(BRCM_CC_43362_CHIP_ID, 13):
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Arend van Spriel <aspriel@gmail.com> Cc: Franky Lin <franky.lin@broadcom.com> Cc: Hante Meuleman <hante.meuleman@broadcom.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: brcm80211-dev-list.pdl@broadcom.com Cc: netdev@vger.kernel.org Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/Ykx0iRlvtBnKqtbG@zn.tnic Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/wireless/mediatek/mt76/mt76x2/pci.c: In function ‘mt76x2e_probe’:
././include/linux/compiler_types.h:352:38: error: call to ‘__compiletime_assert_946’ \
declared with attribute error: FIELD_PREP: mask is not constant
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Felix Fietkau <nbd@nbd.name> Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Cc: Ryder Lee <ryder.lee@mediatek.com> Cc: Shayne Chen <shayne.chen@mediatek.com> Cc: Sean Wang <sean.wang@mediatek.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220405151517.29753-9-bp@alien8.de Signed-off-by: Sasha Levin <sashal@kernel.org>
UBSAN warnings are observed on atlantic driver:
[ 294.432996] UBSAN: array-index-out-of-bounds in /build/linux-Qow4fL/linux-5.15.0/drivers/net/ethernet/aquantia/atlantic/aq_nic.c:484:48
[ 294.433695] index 8 is out of range for type 'aq_vec_s *[8]'
The ring is dereferenced right before breaking out the loop, to prevent
that from happening, only use the index in the loop to fix the issue.
Use the IOCB_DIRECT indicator flag on the I/O context rather than checking to
see if the file was opened O_DIRECT.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: linux-cifs@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
sound/usb/midi.c: In function ‘snd_usbmidi_out_endpoint_create’:
sound/usb/midi.c:1389:2: error: case label does not reduce to an integer constant
case USB_ID(0xfc08, 0x0101): /* Unknown vendor Cable */
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
[ A slight correction with parentheses around the argument by tiwai ]
projects / thirdparty / kernel / stable.git / log
