In case we don't set the sg_prot_tablesize, the scsi layer assign the
default size (65535 entries). We should limit this size since we should
take into consideration the underlaying device capability. This cap is
considered when calculating the sg_tablesize. Otherwise, for example,
we can get that /sys/block/sdb/queue/max_segments is 128 and
/sys/block/sdb/queue/max_integrity_segments is 65535.
This is due to ath10k_hw_mem_layout is not defined for AR9987.
For coredump undefined hw ramdump_size is 0.
Check for the ramdump_size before allocation memory.
Tested on: AR9987, QCA9984
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside a nested 'else' block at the beginning of this function is a
call that assigns 'psta' to the return value of 'rtw_get_stainfo()'.
If 'rtw_get_stainfo()' returns NULL and the flow of control reaches
the 'else if' where 'psta' is dereferenced, then we will dereference
a NULL pointer.
Fix this by checking if 'psta' is not NULL before reading its
'psta->qos_option' data member.
This change is necessary for spidev devices (e.g. /dev/spidev3.0) working
in the slave mode (like NXP's dspi driver for Vybrid SoC).
When SPI HW works in this mode - the master is responsible for providing
CS and CLK signals. However, when some fault happens - like for example
distortion on SPI lines - the SPI Linux driver needs a chance to recover
from this abnormal situation and prepare itself for next (correct)
transmission.
This change doesn't pose any threat on drivers working in master mode as
spi_slave_abort() function checks if SPI slave mode is supported.
Separate the declaration of struct bh1750_chip_info from definition
of bh1750_chip_info_tbl[] in a single statement as it makes the code
hard to read, and with the extra newline it makes it look as if the
bh1750_chip_info_tbl[] had no explicit type.
This change also resolves the following compiler warning about the
unusual position of the static keyword that can be seen when building
with warnings enabled (W=1):
drivers/iio/light/bh1750.c:64:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Related to commit 3a11fbb037a1 ("iio: light: add support for ROHM
BH1710/BH1715/BH1721/BH1750/BH1751 ambient light sensors").
Signed-off-by: Krzysztof Wilczynski <kw@linux.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Panels must be initialised with drm_panel_init(). Add the missing
function call in the panel-raspberrypi-touchscreen.c and
panel-sitronix-st7789v.c drivers.
CA0132 has the delayed HP jack detection code that is invoked from the
unsol handler, but it does a few weird things: it contains the cancel
of a work inside the work handler, and yet it misses the cancel-sync
call at (runtime-)suspend. This patch addresses those issues.
We need to keep power on while processing the DSP response via unsol
event. Each snd_hda_codec_read() call does the power management, so
it should work normally, but still it's safer to keep the power up for
the whole function.
Fixes: a73d511c4867 ("ALSA: hda/ca0132: Add unsol handler for DSP and jack detection") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191213085111.22855-2-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current PCM code doesn't initialize explicitly the buffers
allocated for PCM streams, hence it might leak some uninitialized
kernel data or previous stream contents by mmapping or reading the
buffer before actually starting the stream.
Since this is a common problem, this patch simply adds the clearance
of the buffer data at hw_params callback. Although this does only
zero-clear no matter which format is used, which doesn't mean the
silence for some formats, but it should be OK because the intention is
just to clear the previous data on the buffer.
When a tree mod log user no longer needs to use the tree it calls
btrfs_put_tree_mod_seq() to remove itself from the list of users and
delete all no longer used elements of the tree's red black tree, which
should be all elements with a sequence number less then our equals to
the caller's sequence number. However the logic is broken because it
can delete and free elements from the red black tree that have a
sequence number greater then the caller's sequence number:
1) At a point in time we have sequence numbers 1, 2, 3 and 4 in the
tree mod log;
2) The task which got assigned the sequence number 1 calls
btrfs_put_tree_mod_seq();
3) Sequence number 1 is deleted from the list of sequence numbers;
4) The current minimum sequence number is computed to be the sequence
number 2;
5) A task using sequence number 2 is at tree_mod_log_rewind() and gets
a pointer to one of its elements from the red black tree through
a call to tree_mod_log_search();
6) The task with sequence number 1 iterates the red black tree of tree
modification elements and deletes (and frees) all elements with a
sequence number less then or equals to 2 (the computed minimum sequence
number) - it ends up only leaving elements with sequence numbers of 3
and 4;
7) The task with sequence number 2 now uses the pointer to its element,
already freed by the other task, at __tree_mod_log_rewind(), resulting
in a use-after-free issue. When CONFIG_DEBUG_PAGEALLOC=y it produces
a trace like the following:
Fix this by making btrfs_put_tree_mod_seq() skip deletion of elements that
have a sequence number equals to the computed minimum sequence number, and
not just elements with a sequence number greater then that minimum.
Fixes: bd989ba359f2ac ("Btrfs: add tree modification log functions") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get an -ENOENT back from btrfs_uuid_iter_rem when iterating the
uuid tree we'll just continue and do btrfs_next_item(). However we've
done a btrfs_release_path() at this point and no longer have a valid
path. So increment the key and go back and do a normal search.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to read the fs root corresponding with a reloc root we'll
just break out and free the reloc roots. But we remove our current
reloc_root from this list higher up, which means we'll leak this
reloc_root. Fix this by adding ourselves back to the reloc_roots list
so we are properly cleaned up.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My fsstress modifications coupled with generic/475 uncovered a failure
to mount and replay the log if we hit a orphaned root. We do not want
to replay the log for an orphan root, but it's completely legitimate to
have an orphaned root with a log attached. Fix this by simply skipping
replaying the log. We still need to pin it's root node so that we do
not overwrite it while replaying other logs, as we re-read the log root
at every stage of the replay.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We log warning if root::orphan_cleanup_state is not set to
ORPHAN_CLEANUP_DONE in btrfs_ioctl_send(). However if the filesystem is
mounted as readonly we skip the orphan item cleanup during the lookup
and root::orphan_cleanup_state remains at the init state 0 instead of
ORPHAN_CLEANUP_DONE (2). So during send in btrfs_ioctl_send() we hit the
warning as below.
The warning exists because having orphan inodes could confuse send and
cause it to fail or produce incorrect streams. The two cases that would
cause such send failures, which are already fixed are:
1) Inodes that were unlinked - these are orphanized and remain with a
link count of 0. These caused send operations to fail because it
expected to always find at least one path for an inode. However this
is no longer a problem since send is now able to deal with such
inodes since commit 46b2f4590aab ("Btrfs: fix send failure when root
has deleted files still open") and treats them as having been
completely removed (the state after an orphan cleanup is performed).
2) Inodes that were in the process of being truncated. These resulted in
send not knowing about the truncation and potentially issue write
operations full of zeroes for the range from the new file size to the
old file size. This is no longer a problem because we no longer
create orphan items for truncation since commit f7e9e8fc792f ("Btrfs:
stop creating orphan items for truncate").
As such before these commits, the WARN_ON here provided a clue in case
something went wrong. Instead of being a warning against the
root::orphan_cleanup_state value, it could have been more accurate by
checking if there were actually any orphan items, and then issue a
warning only if any exists, but that would be more expensive to check.
Since orphanized inodes no longer cause problems for send, just remove
the warning.
Reported-by: Christoph Anton Mitterer <calestyo@scientia.net> Link: https://lore.kernel.org/linux-btrfs/21cb5e8d059f6e1496a903fa7bfc0a297e2f5370.camel@scientia.net/ CC: stable@vger.kernel.org # 4.19+ Suggested-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When logging a file that has shared extents (reflinked with other files or
with itself), we can end up logging multiple checksum items that cover
overlapping ranges. This confuses the search for checksums at log replay
time causing some checksums to never be added to the fs/subvolume tree.
Consider the following example of a file that shares the same extent at
offsets 0 and 256Kb:
[ bytenr 13631488, offset 64Kb, len 192Kb ]
64Kb 256Kb
[ bytenr 13893632, offset 0, len 256Kb ]
256Kb 512Kb
When logging the inode, at tree-log.c:copy_items(), when processing the
file extent item at offset 0, we log a checksum item covering the range 13959168 to 14024704, which corresponds to 13893632 + 64Kb and 13893632 +
64Kb + 64Kb, respectively.
Later when processing the extent item at offset 256K, we log the checksums
for the range from 13893632 to 14155776 (which corresponds to 13893632 +
256Kb). These checksums get merged with the checksum item for the range
from 13631488 to 13893632 (13631488 + 256Kb), logged by a previous fsync.
So after this we get the two following checksum items in the log tree:
(...)
item 6 key (EXTENT_CSUM EXTENT_CSUM 13631488) itemoff 3095 itemsize 512
range start 13631488 end 14155776 length 524288
item 7 key (EXTENT_CSUM EXTENT_CSUM 13959168) itemoff 3031 itemsize 64
range start 13959168 end 14024704 length 65536
The first one covers the range from the second one, they overlap.
So far this does not cause a problem after replaying the log, because
when replaying the file extent item for offset 256K, we copy all the
checksums for the extent 13893632 from the log tree to the fs/subvolume
tree, since searching for an checksum item for bytenr 13893632 leaves us
at the first checksum item, which covers the whole range of the extent.
However if we write 64Kb to file offset 256Kb for example, we will
not be able to find and copy the checksums for the last 128Kb of the
extent at bytenr 13893632, referenced by the file range 384Kb to 512Kb.
After writing 64Kb into file offset 256Kb we get the following extent
layout for our file:
[ bytenr 13631488, offset 64Kb, len 192Kb ]
64Kb 256Kb
[ bytenr 14155776, offset 0, len 64Kb ]
256Kb 320Kb
[ bytenr 13893632, offset 64Kb, len 192Kb ]
320Kb 512Kb
After fsync'ing the file, if we have a power failure and then mount
the filesystem to replay the log, the following happens:
1) When replaying the file extent item for file offset 320Kb, we
lookup for the checksums for the extent range from 13959168
(13893632 + 64Kb) to 14155776 (13893632 + 256Kb), through a call
to btrfs_lookup_csums_range();
2) btrfs_lookup_csums_range() finds the checksum item that starts
precisely at offset 13959168 (item 7 in the log tree, shown before);
3) However that checksum item only covers 64Kb of data, and not 192Kb
of data;
4) As a result only the checksums for the first 64Kb of data referenced
by the file extent item are found and copied to the fs/subvolume tree.
The remaining 128Kb of data, file range 384Kb to 512Kb, doesn't get
the corresponding data checksums found and copied to the fs/subvolume
tree.
5) After replaying the log userspace will not be able to read the file
range from 384Kb to 512Kb, because the checksums are missing and
resulting in an -EIO error.
The following steps reproduce this scenario:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt/sdc
$ dmesg | tail
[165305.003464] BTRFS info (device sdc): no csum found for inode 257 start 401408
[165305.004014] BTRFS info (device sdc): no csum found for inode 257 start 405504
[165305.004559] BTRFS info (device sdc): no csum found for inode 257 start 409600
[165305.005101] BTRFS info (device sdc): no csum found for inode 257 start 413696
[165305.005627] BTRFS info (device sdc): no csum found for inode 257 start 417792
[165305.006134] BTRFS info (device sdc): no csum found for inode 257 start 421888
[165305.006625] BTRFS info (device sdc): no csum found for inode 257 start 425984
[165305.007278] BTRFS info (device sdc): no csum found for inode 257 start 430080
[165305.008248] BTRFS warning (device sdc): csum failed root 5 ino 257 off 393216 csum 0x1337385e expected csum 0x00000000 mirror 1
[165305.009550] BTRFS warning (device sdc): csum failed root 5 ino 257 off 393216 csum 0x1337385e expected csum 0x00000000 mirror 1
Fix this simply by deleting first any checksums, from the log tree, for the
range of the extent we are logging at copy_items(). This ensures we do not
get checksum items in the log tree that have overlapping ranges.
This is a long time issue that has been present since we have the clone
(and deduplication) ioctl, and can happen both when an extent is shared
between different files and within the same file.
A test case for fstests follows soon.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing with the new fsstress uncovered a pretty nasty deadlock with
lookup and snapshot deletion.
Process A
unlink
-> final iput
-> inode_tree_del
-> synchronize_srcu(subvol_srcu)
Process B
btrfs_lookup <- srcu_read_lock() acquired here
-> btrfs_iget
-> find inode that has I_FREEING set
-> __wait_on_freeing_inode()
We're holding the srcu_read_lock() while doing the iget in order to make
sure our fs root doesn't go away, and then we are waiting for the inode
to finish freeing. However because the free'ing process is doing a
synchronize_srcu() we deadlock.
Fix this by dropping the synchronize_srcu() in inode_tree_del(). We
don't need people to stop accessing the fs root at this point, we're
only adding our empty root to the dead roots list.
A larger much more invasive fix is forthcoming to address how we deal
with fs roots, but this fixes the immediate problem.
Fixes: 76dda93c6ae2 ("Btrfs: add snapshot/subvolume destroy ioctl") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're rename exchanging two subvols we'll try to lock this lock
twice, which is bad. Just lock once if either of the ino's are subvols.
Fixes: cdd1fedf8261 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating the second host in h2_create(), two addresses are assigned
to the interface, but only one is deleted. When running the test twice
in a row the following error is observed:
$ ./router_bridge_vlan.sh
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: vlan [ OK ]
$ ./router_bridge_vlan.sh
RTNETLINK answers: File exists
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: vlan [ OK ]
Fix this by deleting the address during cleanup.
Fixes: 5b1e7f9ebd56 ("selftests: forwarding: Test routed bridge interface") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
where 'addr' is set by sctp_v4_from_addr_param(), and it doesn't initialize
the padding of addr->v4.
Later when calling sctp_make_heartbeat(), hbinfo.daddr(=transport->ipaddr)
will become the part of skb, and the issue occurs.
This patch is to fix it by initializing the padding of addr->v4 in
sctp_v4_from_addr_param(), as well as other functions that do the similar
thing, and these functions shouldn't trust that the caller initializes the
memory, as Marcelo suggested.
Reported-by: syzbot+6dcbfea81cd3d4dd0b02@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver doesn't accommodate the configuration for max number
of multicast mac addresses, in such particular case it leaves
the device with improper/invalid multicast configuration state,
causing connectivity issues (in lacp bonding like scenarios).
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") introduced
a regression in driver that when xdp program is installed on
qede device, device's aggregation feature (hardware GRO) is not
getting disabled, which is unexpected with xdp.
Fixes: 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.
Fixes: ce85e13ad6ef ("lan78xx: Update to use phylib instead of mii_if_info.") Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ql_alloc_large_buffers() has the usual RX buffer allocation
loop where it allocates skbs and maps them for DMA. It also
treats failure as a fatal error.
There are (at least) three bugs in the error paths:
1. ql_free_large_buffers() assumes that the lrg_buf[] entry for the
first buffer that couldn't be allocated will have .skb == NULL.
But the qla_buf[] array is not zero-initialised.
2. ql_free_large_buffers() DMA-unmaps all skbs in lrg_buf[]. This is
incorrect for the last allocated skb, if DMA mapping failed.
3. Commit 1acb8f2a7a9f ("net: qlogic: Fix memory leak in
ql_alloc_large_buffers") added a direct call to dev_kfree_skb_any()
after the skb is recorded in lrg_buf[], so ql_free_large_buffers()
will double-free it.
The bugs are somewhat inter-twined, so fix them all at once:
* Clear each entry in qla_buf[] before attempting to allocate
an skb for it. This goes half-way to fixing bug 1.
* Set the .skb field only after the skb is DMA-mapped. This
fixes the rest.
Fixes: 1357bfcf7106 ("qla3xxx: Dynamically size the rx buffer queue ...") Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() ...") Fixes: 1acb8f2a7a9f ("net: qlogic: Fix memory leak in ql_alloc_large_buffers") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
net/nfc/nci/uart.c, 349:
nci_skb_alloc in nci_uart_default_recv_buf
net/nfc/nci/uart.c, 255:
(FUNC_PTR)nci_uart_default_recv_buf in nci_uart_tty_receive
net/nfc/nci/uart.c, 254:
spin_lock in nci_uart_tty_receive
nci_skb_alloc(GFP_KERNEL) can sleep at runtime.
(FUNC_PTR) means a function pointer is called.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC for
nci_skb_alloc().
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pre-modification code:
int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
[...]
[1] priv->tx_head = TX_NEXT(tx_head);
[2] count++;
[3] netdev_sent_queue(ndev, skb->len);
[...]
}
An rx interrupt occurs if hip04_mac_start_xmit just executes to the line 2,
tx_head has been updated, but corresponding 'skb->len' has not been
added to dql_queue.
And then
hip04_mac_interrupt->__napi_schedule->hip04_rx_poll->hip04_tx_reclaim
In hip04_tx_reclaim, because tx_head has been updated,
bytes_compl will plus an additional "skb-> len"
which has not been added to dql_queue. And then
trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed).
To solve the problem described above, we put
"netdev_sent_queue(ndev, skb->len);"
before
"priv->tx_head = TX_NEXT(tx_head);"
Fixes: a41ea46a9a12 ("net: hisilicon: new hip04 ethernet driver") Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When storing a pointer to a dst_metrics structure in dst_entry._metrics,
two flags are added in the least significant bits of the pointer value.
Hence this assumes all pointers to dst_metrics structures have at least
4-byte alignment.
However, on m68k, the minimum alignment of 32-bit values is 2 bytes, not
4 bytes. Hence in some kernel builds, dst_default_metrics may be only
2-byte aligned, leading to obscure boot warnings like:
Fix this by forcing 4-byte alignment of all dst_metrics structures.
Fixes: e5fd387ad5b30ca3 ("ipv6: do not overwrite inetpeer metrics prematurely") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a PHY is probed, if the top bit is set, we end up requesting a
module with the string "mdio:-10101110000000100101000101010001" -
the top bit is printed to a signed -1 value. This leads to the module
not being loaded.
Fix the module format string and the macro generating the values for
it to ensure that we only print unsigned types and the top bit is
always 0/1. We correctly end up with
"mdio:10101110000000100101000101010001".
Fixes: 8626d3b43280 ("phylib: Support phy module autoloading") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is softlockup when using TPACKET_V3:
...
NMI watchdog: BUG: soft lockup - CPU#2 stuck for 60010ms!
(__irq_svc) from [<c0558a0c>] (_raw_spin_unlock_irqrestore+0x44/0x54)
(_raw_spin_unlock_irqrestore) from [<c027b7e8>] (mod_timer+0x210/0x25c)
(mod_timer) from [<c0549c30>]
(prb_retire_rx_blk_timer_expired+0x68/0x11c)
(prb_retire_rx_blk_timer_expired) from [<c027a7ac>]
(call_timer_fn+0x90/0x17c)
(call_timer_fn) from [<c027ab6c>] (run_timer_softirq+0x2d4/0x2fc)
(run_timer_softirq) from [<c021eaf4>] (__do_softirq+0x218/0x318)
(__do_softirq) from [<c021eea0>] (irq_exit+0x88/0xac)
(irq_exit) from [<c0240130>] (msa_irq_exit+0x11c/0x1d4)
(msa_irq_exit) from [<c0209cf0>] (handle_IPI+0x650/0x7f4)
(handle_IPI) from [<c02015bc>] (gic_handle_irq+0x108/0x118)
(gic_handle_irq) from [<c0558ee4>] (__irq_usr+0x44/0x5c)
...
If __ethtool_get_link_ksettings() is failed in
prb_calc_retire_blk_tmo(), msec and tmo will be zero, so tov_in_jiffies
is zero and the timer expire for retire_blk_timer is turn to
mod_timer(&pkc->retire_blk_timer, jiffies + 0),
which will trigger cpu usage of softirq is 100%.
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.") Tested-by: Xiao Jiangfeng <xiaojiangfeng@huawei.com> Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
When a port sends PLOGI, discovery state should be changed to login
pending, otherwise RELOGIN_NEEDED bit is set in
qla24xx_handle_plogi_done_event(). RELOGIN_NEEDED triggers another PLOGI,
and it never goes out of the loop until login timer expires.
Fixes: 8777e4314d397 ("scsi: qla2xxx: Migrate NVME N2N handling into state machine") Fixes: 8b5292bcfcacf ("scsi: qla2xxx: Fix Relogin to prevent modifying scan_state flag") Cc: Quinn Tran <qutran@marvell.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191125165702.1013-6-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some time ago the block layer was modified such that timeout handlers are
called from thread context instead of interrupt context. Make it safe to
run the iSCSI timeout handler in thread context. This patch fixes the
following lockdep complaint:
================================
WARNING: inconsistent lock state
5.5.1-dbg+ #11 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/7:1H/206 [HC0[0]:SC0[0]:HE1:SE1] takes: ffff88802d9827e8 (&(&session->frwd_lock)->rlock){+.?.}, at: iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_check_transport_timeouts+0x3e/0x210 [libiscsi]
call_timer_fn+0x132/0x470
__run_timers.part.0+0x39f/0x5b0
run_timer_softirq+0x63/0xc0
__do_softirq+0x12d/0x5fd
irq_exit+0xb3/0x110
smp_apic_timer_interrupt+0x131/0x3d0
apic_timer_interrupt+0xf/0x20
default_idle+0x31/0x230
arch_cpu_idle+0x13/0x20
default_idle_call+0x53/0x60
do_idle+0x38a/0x3f0
cpu_startup_entry+0x24/0x30
start_secondary+0x222/0x290
secondary_startup_64+0xa4/0xb0
irq event stamp: 1383705
hardirqs last enabled at (1383705): [<ffffffff81aace5c>] _raw_spin_unlock_irq+0x2c/0x50
hardirqs last disabled at (1383704): [<ffffffff81aacb98>] _raw_spin_lock_irq+0x18/0x50
softirqs last enabled at (1383690): [<ffffffffa0e2efea>] iscsi_queuecommand+0x76a/0xa20 [libiscsi]
softirqs last disabled at (1383682): [<ffffffffa0e2e998>] iscsi_queuecommand+0x118/0xa20 [libiscsi]
other info that might help us debug this:
Possible unsafe locking scenario:
Fixes: 287922eb0b18 ("block: defer timeouts to a workqueue") Cc: Christoph Hellwig <hch@lst.de> Cc: Keith Busch <keith.busch@intel.com> Cc: Lee Duncan <lduncan@suse.com> Cc: Chris Leech <cleech@redhat.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191209173457.187370-1-bvanassche@acm.org Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We got the following warnings from thin_check during thin-pool setup:
$ thin_check /dev/vdb
examining superblock
examining devices tree
missing devices: [1, 84]
too few entries in btree_node: 41, expected at least 42 (block 138, max_entries = 126)
examining mapping tree
The phenomenon is the number of entries in one node of details_info tree is
less than (max_entries / 3). And it can be easily reproduced by the following
procedures:
$ new a thin pool
$ presume the max entries of details_info tree is 126
$ new 127 thin devices (e.g. 1~127) to make the root node being full
and then split
$ remove the first 43 (e.g. 1~43) thin devices to make the children
reblance repeatedly
$ stop the thin pool
$ thin_check
The root cause is that the B-tree removal procedure in __rebalance2()
doesn't guarantee the invariance: the minimal number of entries in
non-root node should be >= (max_entries / 3).
Simply fix the problem by increasing the rebalance threshold to
make sure the number of entries in each child will be greater
than or equal to (max_entries / 3 + 1), so no matter which
child is used for removal, the number will still be valid.
Cc: stable@vger.kernel.org Signed-off-by: Hou Tao <houtao1@huawei.com> Acked-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes the branching for edge-case where no SCSI device handler
exists. The __map_bio_fast() method was far too limited, by only
selecting a new pathgroup or path IFF there was a path failure, fix this
be eliminating it in favor of __map_bio(). __map_bio()'s extra SCSI
device handler specific MPATHF_PG_INIT_REQUIRED test is not in the fast
path anyway.
This change restores full path selector functionality for bio-based
configurations that don't haave a SCSI device handler. But it should be
noted that the path selectors do have an impact on performance for
certain networks that are extremely fast (and don't require frequent
switching).
Fixes: 8d47e65948dd ("dm mpath: remove unnecessary NVMe branching in favor of scsi_dh checks") Cc: stable@vger.kernel.org Reported-by: Drew Hastings <dhastings@crucialwebhost.com> Suggested-by: Martin Wilck <mwilck@suse.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 222ec1618c3ace ("drm: Add aspect ratio parsing in DRM
layer") the drm core started honoring the picture_aspect_ratio field
when comparing two drm_display_modes. Prior to that it was ignored.
When the CVBS encoder driver was initially submitted there was no aspect
ratio check.
Switch from drm_mode_equal() to drm_mode_match() without
DRM_MODE_MATCH_ASPECT_RATIO to fix "kmscube" and X.org output using the
CVBS connector. When (for example) kmscube sets the output mode when
using the CVBS connector it passes HDMI_PICTURE_ASPECT_NONE, making the
drm_mode_equal() fail as it include the aspect ratio.
Prior to this patch kmscube reported:
failed to set mode: Invalid argument
The CVBS mode checking in the sun4i (drivers/gpu/drm/sun4i/sun4i_tv.c
sun4i_tv_mode_to_drm_mode) and ZTE (drivers/gpu/drm/zte/zx_tvenc.c
tvenc_mode_{pal,ntsc}) drivers don't set the "picture_aspect_ratio" at
all. The Meson VPU driver does not rely on the aspect ratio for the CVBS
output so we can safely decouple it from the hdmi_picture_aspect
setting.
Cc: <stable@vger.kernel.org> Fixes: 222ec1618c3ace ("drm: Add aspect ratio parsing in DRM layer") Fixes: bbbe775ec5b5da ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: squashed with drm: meson: venc: cvbs: deduplicate the meson_cvbs_mode lookup code] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191208171832.1064772-3-martin.blumenstingl@googlemail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since irq_bypass_register_producer() is called after request_irq(), we
should do tear-down in reverse order: irq_bypass_unregister_producer()
then free_irq().
Specifically free_irq() may release resources required by the
irqbypass del_producer() callback. Notably an example provided by
Marc Zyngier on arm64 with GICv4 that he indicates has the potential
to wedge the hardware:
free_irq(irq)
__free_irq(irq)
irq_domain_deactivate_irq(irq)
its_irq_domain_deactivate()
[unmap the VLPI from the ITS]
kvm_arch_irq_bypass_del_producer(cons, prod)
kvm_vgic_v4_unset_forwarding(kvm, irq, ...)
its_unmap_vlpi(irq)
[Unmap the VLPI from the ITS (again), remap the original LPI]
Signed-off-by: Jiang Yi <giangyi@amazon.com> Cc: stable@vger.kernel.org # v4.4+ Fixes: 6d7425f109d26 ("vfio: Register/unregister irq_bypass_producer") Link: https://lore.kernel.org/kvm/20191127164910.15888-1-giangyi@amazon.com Reviewed-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Eric Auger <eric.auger@redhat.com>
[aw: commit log] Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If Close command is interrupted before sending a request
to the server the client ends up leaking an open file
handle. This wastes server resources and can potentially
block applications that try to remove the file or any
directory containing this file.
Fix this by putting the close command into a worker queue,
so another thread retries it later.
Cc: Stable <stable@vger.kernel.org> Tested-by: Frank Sorenson <sorenson@redhat.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the client translates O_SYNC and O_DIRECT flags
into corresponding SMB create options when openning a file.
The problem is that on reconnect when the file is being
re-opened the client doesn't set those flags and it causes
a server to reject re-open requests because create options
don't match. The latter means that any subsequent system
call against that open file fail until a share is re-mounted.
Fix this by properly setting SMB create options when
re-openning files after reconnects.
Fixes: 1013e760d10e6: ("SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags") Cc: Stable <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On reconnect, the transport data structure is NULL and its information is not
available.
Signed-off-by: Long Li <longli@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While it's not friendly to fail user processes that issue more iovs
than we support, at least we should return the correct error code so the
user process gets a chance to retry with smaller number of iovs.
Signed-off-by: Long Li <longli@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Long Li <longli@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During reconnecting, the transport may have already been destroyed and is in
the process being reconnected. In this case, return -EAGAIN to not fail and
to retry this I/O.
Signed-off-by: Long Li <longli@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attempting to transmit rx_done messages after the GLINK instance is
being torn down will cause use after free and memory leaks. So cancel
the intent_work and free up the pending intents.
With this there are no concurrent accessors of the channel left during
qcom_glink_native_remove() and there is therefor no need to hold the
spinlock during this operation - which would prohibit the use of
cancel_work_sync() in the release function. So remove this.
The device release function is set before registering with rpmsg. If
rpmsg registration fails, the framework will call device_put(), which
invokes the release function. The channel create logic does not need to
free rpdev if rpmsg_register_device() fails and release is called.
In a remote processor crash scenario, there is no guarantee the remote
processor sent close requests before it went into a bad state. Remove
the reference that is normally handled by the close command in the
so channel resources can be released.
Virtual and translated addresses retrieved by the xtensa TLB sanity
checker must be consistent, i.e. correspond to the same state of the
checked TLB entry. KASAN shadow memory is mapped dynamically using
auto-refill TLB entries and thus may change TLB state between the
virtual and translated address retrieval, resulting in false TLB
insanity report.
Move read_xtlb_translation close to read_xtlb_virtual to make sure that
read values are consistent.
Cc: stable@vger.kernel.org Fixes: a99e07ee5e88 ("xtensa: check TLB sanity on return to userspace") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver enables MSI-X, msix_program_entries() reads the MSI-X Vector
Control register for each vector and saves it in desc->masked. Each
register is 32 bits and bit 0 is the actual Mask bit.
When we restored these registers during resume, we previously set the Mask
bit if *any* bit in desc->masked was set instead of when the Mask bit
itself was set:
pci_restore_state
pci_restore_msi_state
__pci_restore_msix_state
for_each_pci_msi_entry
msix_mask_irq(entry, entry->masked) <-- entire u32 word
__pci_msix_desc_mask_irq(desc, flag)
mask_bits = desc->masked & ~PCI_MSIX_ENTRY_CTRL_MASKBIT
if (flag) <-- testing entire u32, not just bit 0
mask_bits |= PCI_MSIX_ENTRY_CTRL_MASKBIT
writel(mask_bits, desc_addr + PCI_MSIX_ENTRY_VECTOR_CTRL)
This means that after resume, MSI-X vectors were masked when they shouldn't
be, which leads to timeouts like this:
According to documentation [0] the correct offset for the Upstream Peer
Decode Configuration Register (UPDCR) is 0x1014. It was previously defined
as 0x1114.
d99321b63b1f ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
intended to enforce isolation between PCI devices allowing them to be put
into separate IOMMU groups. Due to the wrong register offset the intended
isolation was not fully enforced. This is fixed with this patch.
Please note that I did not test this patch because I have no hardware that
implements this register.
A sysfs request to enable or disable a PCIe hotplug slot should not
return before it has been carried out. That is sought to be achieved by
waiting until the controller's "pending_events" have been cleared.
However the IRQ thread pciehp_ist() clears the "pending_events" before
it acts on them. If pciehp_sysfs_enable_slot() / _disable_slot() happen
to check the "pending_events" after they have been cleared but while
pciehp_ist() is still running, the functions may return prematurely
with an incorrect return value.
Fix by introducing an "ist_running" flag which must be false before a sysfs
request is allowed to return.
pci_pm_thaw_noirq() is supposed to return the device to D0 and restore its
configuration registers, but previously it only did that for devices whose
drivers implemented the new power management ops.
Hibernation, e.g., via "echo disk > /sys/power/state", involves freezing
devices, creating a hibernation image, thawing devices, writing the image,
and powering off. The fact that thawing did not return devices with legacy
power management to D0 caused errors, e.g., in this path:
pci_pm_thaw_noirq
if (pci_has_legacy_pm_support(pci_dev)) # true for Mellanox VF driver
return pci_legacy_resume_early(dev) # ... legacy PM skips the rest
pci_set_power_state(pci_dev, PCI_D0)
pci_restore_state(pci_dev)
pci_pm_thaw
if (pci_has_legacy_pm_support(pci_dev))
pci_legacy_resume
drv->resume
mlx4_resume
...
pci_enable_msix_range
...
if (dev->current_state != PCI_D0) # <---
return -EINVAL;
which caused these warnings:
mlx4_core a6d1:00:02.0: INTx is not supported in multi-function mode, aborting
PM: dpm_run_callback(): pci_pm_thaw+0x0/0xd7 returns -95
PM: Device a6d1:00:02.0 failed to thaw: error -95
Return devices to D0 and restore config registers for all devices, not just
those whose drivers support new power management.
[bhelgaas: also call pci_restore_state() before pci_legacy_resume_early(),
update comment, add stable tag, commit log] Link: https://lore.kernel.org/r/KU1P153MB016637CAEAD346F0AA8E3801BFAD0@KU1P153MB0166.APCP153.PROD.OUTLOOK.COM Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable@vger.kernel.org # v4.13+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MMC IOCTLS with R1B responses may cause the card to enter the busy state,
which means it's not ready to receive a new request. To prevent new
requests from being sent to the card, use a CMD13 polling loop to verify
that the card returns to the transfer state, before completing the request.
To prepare for more users of card_busy_detect(), let's drop the struct
request * as an in-parameter and convert to log the error message via
dev_err() instead of pr_err().
Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.
Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64e269 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.
That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.
Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.
Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().
However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.
In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.
Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.
Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.
Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.
For example, let's consider the following scenario on a system
with HZ=1000:
* The synflood timestamp is 0, either because that's the timestamp
of the last synflood or, more commonly, because we're working with
a freshly created socket.
* We receive a new SYN, which triggers synflood protection. Let's say
that this happens when jiffies == 2147484649 (that is,
'synflood timestamp' + HZ + 2^31 + 1).
* Then tcp_synq_overflow() doesn't update the synflood timestamp,
because time_after32(2147484649, 1000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 1000: the value of 'last_overflow' + HZ.
* A bit later, we receive the ACK completing the 3WHS. But
cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
says that we're not under synflood. That's because
time_after32(2147484649, 120000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.
Of course, in reality jiffies would have increased a bit, but this
condition will last for the next 119 seconds, which is far enough
to accommodate for jiffie's growth.
Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.
Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.
Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.
For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit cca9bab1b72c ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.
Fixes: cca9bab1b72c ("tcp: use monotonic timestamps for PAWS") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user changes prio2buffer mapping while global pause is
enabled, mlx5 driver incorrectly sets all active buffers
(buffer that has at least one priority mapped) to lossy.
Solution:
If global pause is enabled, set all the active buffers to lossless
in prio2buffer command.
Also, add error message when buffer size is not enough to meet
xoff threshold.
In order to set/get/dump, the tipc uses the generic netlink
infrastructure. So, when tipc module is inserted, init function
calls genl_register_family().
After genl_register_family(), set/get/dump commands are immediately
allowed and these callbacks internally use the net_generic.
net_generic is allocated by register_pernet_device() but this
is called after genl_register_family() in the __init function.
So, these callbacks would use un-initialized net_generic.
Test commands:
#SHELL1
while :
do
modprobe tipc
modprobe -rv tipc
done
Fixes: 7e4369057806 ("tipc: fix a slab object leak") Fixes: a62fbccecd62 ("tipc: make subscriber server support net namespace") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The openvswitch module shares a common conntrack and NAT infrastructure
exposed via netfilter. It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision. Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress. The openvswitch module doesn't have such capability.
Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.
Fixes: 05752523e565 ("openvswitch: Interface with NAT.") Signed-off-by: Aaron Conole <aconole@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 2b3e88ea6528 ("net: phy: improve phy state checking")
phy_start_aneg() expects phy state to be >= PHY_UP. Call phy_start()
before calling phy_start_aneg() during probe so that autonegotiation
is initiated.
As phy_start() takes care of calling phy_start_aneg(), drop the explicit
call to phy_start_aneg().
Network fails without this patch on Octeon TX.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking") Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sch->q.len hasn't been set if the subqueue is a NOLOCK qdisc
in mq_dump() and mqprio_dump().
Fixes: ce679e8df7ed ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio") Signed-off-by: Dust Li <dust.li@linux.alibaba.com> Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 43e665287f93 ("net-next: dsa: fix flow dissection") added an
ability to override protocol and network offset during flow dissection
for DSA-enabled devices (i.e. controllers shipped as switch CPU ports)
in order to fix skb hashing for RPS on Rx path.
However, skb_hash() and added part of code can be invoked not only on
Rx, but also on Tx path if we have a multi-queued device and:
- kernel is running on UP system or
- XPS is not configured.
The call stack in this two cases will be like: dev_queue_xmit() ->
__dev_queue_xmit() -> netdev_core_pick_tx() -> netdev_pick_tx() ->
skb_tx_hash() -> skb_get_hash().
The problem is that skbs queued for Tx have both network offset and
correct protocol already set up even after inserting a CPU tag by DSA
tagger, so calling tag_ops->flow_dissect() on this path actually only
breaks flow dissection and hashing.
This can be observed by adding debug prints just before and right after
tag_ops->flow_dissect() call to the related block of code:
In order to fix that we can add the check 'proto == htons(ETH_P_XDSA)'
to prevent code from calling tag_ops->flow_dissect() on Tx.
I also decided to initialize 'offset' variable so tagger callbacks can
now safely leave it untouched without provoking a chaos.
Fixes: 43e665287f93 ("net-next: dsa: fix flow dissection") Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have an interesting memory leak in the bridge when it is being
unregistered and is a slave to a master device which would change the
mac of its slaves on unregister (e.g. bond, team). This is a very
unusual setup but we do end up leaking 1 fdb entry because
dev_set_mac_address() would cause the bridge to insert the new mac address
into its table after all fdbs are flushed, i.e. after dellink() on the
bridge has finished and we call NETDEV_UNREGISTER the bond/team would
release it and will call dev_set_mac_address() to restore its original
address and that in turn will add an fdb in the bridge.
One fix is to check for the bridge dev's reg_state in its
ndo_set_mac_address callback and return an error if the bridge is not in
NETREG_REGISTERED.
Easy steps to reproduce:
1. add bond in mode != A/B
2. add any slave to the bond
3. add bridge dev as a slave to the bond
4. destroy the bridge device
Fixes: 43598813386f ("bridge: add local MAC address to forwarding table (v2)") Reported-by: syzbot+2add91c08eb181fea1bf@syzkaller.appspotmail.com Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When user runs a command like
tc qdisc add dev eth1 root mqprio
KASAN stack-out-of-bounds warning is emitted.
Currently, NLA_ALIGN macro used in mqprio_dump provides too large
buffer size as argument for nla_put and memcpy down the call stack.
The flow looks like this:
1. nla_put expects exact object size as an argument;
2. Later it provides this size to memcpy;
3. To calculate correct padding for SKB, nla_put applies NLA_ALIGN
macro itself.
Therefore, NLA_ALIGN should not be applied to the nla_put parameter.
Otherwise it will lead to out-of-bounds memory access in memcpy.
Fixes: 4e8b86c06269 ("mqprio: Introduce new hardware offload mode and shaper in mqprio") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot was once again able to crash a host by setting a very small mtu
on loopback device.
Let's make inetdev_valid_mtu() available in include/net/ip.h,
and use it in ip_setup_cork(), so that we protect both ip_append_page()
and __ip_append_data()
Also add a READ_ONCE() when the device mtu is read.
Pairs this lockless read with one WRITE_ONCE() in __dev_set_mtu(),
even if other code paths might write over this field.
Add a big comment in include/linux/netdevice.h about dev->mtu
needing READ_ONCE()/WRITE_ONCE() annotations.
Hopefully we will add the missing ones in followup patches.
Fixes: 1470ddf7f8ce ("inet: Remove explicit write references to sk/inet in ip_append_data") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In attach_node_and_children memory is allocated for full_name via
kasprintf. If the condition of the 1st if is not met the function
returns early without freeing the memory. Add a kfree() to fix that.
This has been detected with kmemleak: Link: https://bugzilla.kernel.org/show_bug.cgi?id=205327
It looks like the leak was introduced by this commit: Fixes: 5babefb7f7ab ("of: unittest: allow base devicetree to have symbol metadata") Signed-off-by: Erhard Furtner <erhard_f@mailbox.org> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using this driver on a Blizzard 1260, there were failures whenever DMA
transfers from the SCSI bus to memory of 65535 bytes were followed by a DMA
transfer of 1 byte. This caused the byte at offset 65535 to be overwritten
with 0xff. The Blizzard hardware can't handle single byte DMA transfers.
Besides this issue, limiting the DMA length to something that is not a
multiple of the page size is very inefficient on most file systems.
It seems this limit was chosen because the DMA transfer counter of the ESP
by default is 16 bits wide, thus limiting the length to 65535 bytes.
However, the value 0 means 65536 bytes, which is handled by the ESP and the
Blizzard just fine. It is also the default maximum used by esp_scsi when
drivers don't provide their own dma_length_limit() function.
The limit of 65536 bytes can be used by all boards except the Fastlane. The
old driver used a limit of 65532 bytes (0xfffc), which is reintroduced in
this patch.
Fixes: b7ded0e8b0d1 ("scsi: zorro_esp: Limit DMA transfers to 65535 bytes") Link: https://lore.kernel.org/r/20191112175523.23145-1-jongk@linux-m68k.org Signed-off-by: Kars de Jong <jongk@linux-m68k.org> Reviewed-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 5c089fd0c734 ("idr: Fix idr_get_next race with idr_remove")
neglected to fix idr_get_next_ul(). As far as I can tell, nobody's
actually using this interface under the RCU read lock, but fix it now
before anybody decides to use it.
Fixes: 5c089fd0c734 ("idr: Fix idr_get_next race with idr_remove") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver only supports 3-axis gyro and/or 3-axis accel.
For icm20602, temp data is mandatory for all configurations.
Fix all single and double axis configurations (almost never used) and more
importantly fix 3-axis gyro and 6-axis accel+gyro buffer on icm20602 when
temp data is not enabled.
When a port sends PLOGI, discovery state should be changed to login
pending, otherwise RELOGIN_NEEDED bit is set in
qla24xx_handle_plogi_done_event(). RELOGIN_NEEDED triggers another PLOGI,
and it never goes out of the loop until login timer expires.
Fixes: 8777e4314d397 ("scsi: qla2xxx: Migrate NVME N2N handling into state machine") Fixes: 8b5292bcfcacf ("scsi: qla2xxx: Fix Relogin to prevent modifying scan_state flag") Cc: Quinn Tran <qutran@marvell.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191125165702.1013-6-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit 6ce220dd2f8ea71d6afc29b9a7524c12e39f374a ("raid5: don't set
STRIPE_HANDLE to stripe which is in batch list"), we don't want to set
STRIPE_HANDLE flag for sh which is already in batch list.
However, the stripe which is the head of batch list should set this flag,
otherwise panic could happen inside init_stripe at BUG_ON(sh->batch_head),
it is reproducible with raid5 on top of nvdimm devices per Xiao oberserved.
Thanks for Xiao's effort to verify the change.
Fixes: 6ce220dd2f8ea ("raid5: don't set STRIPE_HANDLE to stripe which is in batch list") Reported-by: Xiao Ni <xni@redhat.com> Tested-by: Xiao Ni <xni@redhat.com> Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Terra Pad 1061 has the usual micro-USB-B id-pin handler, but instead
of controlling the actual micro-USB-B it turns the 5V boost for the
tablet's USB-A connector and its keyboard-cover connector off.
The actual micro-USB-B connector on the tablet is wired for charging only,
and its id pin is *not* connected to the GPIO which is used for the
(broken) id-pin event handler in the DSDT.
While at it not only add a comment why the Terra Pad 1061 is on the
blacklist, but also fix the missing comment for the Minix Neo Z83-4 entry.
Fixes: 61f7f7c8f978 ("gpiolib: acpi: Add gpiolib_acpi_run_edge_events_on_boot option and blacklist") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We used to skip reconnects on all SMB2_IOCTL commands due to SMB3+
FSCTL_VALIDATE_NEGOTIATE_INFO - which made sense since we're still
establishing a SMB session.
However, when refresh_cache_worker() calls smb2_get_dfs_refer() and
we're under reconnect, SMB2_ioctl() will not be able to get a proper
status error (e.g. -EHOSTDOWN in case we failed to reconnect) but an
-EAGAIN from cifs_send_recv() thus looping forever in
refresh_cache_worker().
Fixes: e99c63e4d86d ("SMB3: Fix deadlock in validate negotiate hits reconnect") Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Suggested-by: Aurelien Aptel <aaptel@suse.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
No changeset entries are created for #address-cells and #size-cells
properties, but the duplicated properties are never freed. This
results in a memory leak which is detected by kmemleak:
Commit 9287c6452d2b fixed a situation in which gfs2 could use a glock
after it had been freed. To do that, it temporarily added a new glock
reference by calling gfs2_glock_hold in function gfs2_add_revoke.
However, if the bd element was removed by gfs2_trans_remove_revoke, it
failed to drop the additional reference.
This patch adds logic to gfs2_trans_remove_revoke to properly drop the
additional glock reference.
strictly enforces the MACCTLR inizialization value - 39.3.1 - "Initial
Setting of PCI Express":
"Be sure to write the initial value (= H'80FF 0000) to MACCTLR before
enabling PCIETCTLR.CFINIT".
To avoid unexpected behavior and to match the SW initialization sequence
guidelines, this patch programs the MACCTLR with the correct value.
Note that the MACCTLR.SPCHG bit in the MACCTLR register description
reports that "Only writing 1 is valid and writing 0 is invalid" but this
"invalid" has to be interpreted as a write-ignore aka "ignored", not
"prohibited".
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com> Fixes: c25da4778803 ("PCI: rcar: Add Renesas R-Car PCIe driver") Fixes: be20bbcb0a8c ("PCI: rcar: Add the initialization of PCIe link in resume_noirq()") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: <stable@vger.kernel.org> # v5.2+ Signed-off-by: Sasha Levin <sashal@kernel.org>
The NETDEV_CHANGENAME code is not "unneeded" like it is stated in commit 4cb6560514fa ("leds: trigger: netdev: fix refcnt leak on interface
rename").
The event was accidentally misinterpreted equivalent to
NETDEV_UNREGISTER, but should be equivalent to NETDEV_REGISTER.
This was the case in the original code from the openwrt project.
Otherwise, you are unable to set netdev led triggers for (non-existent)
netdevices, which has to be renamed. This is the case, for example, for
ppp interfaces in openwrt.
Fixes: 06f502f57d0d ("leds: trigger: Introduce a NETDEV trigger") Fixes: 4cb6560514fa ("leds: trigger: netdev: fix refcnt leak on interface rename") Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
