Commit 007bea098b86 (intel_pstate: Add setting voltage value for
baytrail P states.) introduced byt_set_pstate() with the assumption that
it would always be run by the CPU whose MSR is to be written by it. It
turns out, however, that is not always the case in practice, so modify
byt_set_pstate() to enforce the MSR write done by it to always happen on
the right CPU.
Fixes: 007bea098b86 (intel_pstate: Add setting voltage value for baytrail P states.) Signed-off-by: Joe Konno <joe.konno@intel.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fixed by taking the mutex in blktrans_open and blktrans_release.
Note that this locking is already suggested in
include/linux/mtd/blktrans.h:
struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};
But we weren't following it.
Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.
Reported-by: Zhang Xingcai <zhangxingcai@huawei.com> Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fix a race (with some kernel configurations) where a queued
master->pump_messages runs and frees dummy_tx/rx before
spi_unmap_msg is running (or is finished).
This results in the following messages:
BUG: Bad page state in process
page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x200(arch_1)
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
...
Reported-by: Noralf Trønnes <noralf@tronnes.org> Suggested-by: Noralf Trønnes <noralf@tronnes.org> Tested-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up to 7 values:
drivers/media/dvb-frontends/s5h1420.c:193 s5h1420_send_master_cmd() error: buffer overflow 'cmd->msg' 6 <= 7
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Derek noticed that a critical MCE gets reported with the wrong
error type description:
[Hardware Error]: CPU 34: Machine Check Exception: 5 Bank 9: f200003f000100b0
[Hardware Error]: RIP !INEXACT! 10:<ffffffff812e14c1> {intel_idle+0xb1/0x170}
[Hardware Error]: TSC 49587b8e321cb
[Hardware Error]: PROCESSOR 0:306e4 TIME 1431561296 SOCKET 1 APIC 29
[Hardware Error]: Some CPUs didn't answer in synchronization
[Hardware Error]: Machine check: Invalid
^^^^^^^
The last line with 'Invalid' should have printed the high level
MCE error type description we get from mce_severity, i.e.
something like:
[Hardware Error]: Machine check: Action required: data load error in a user process
this happens due to the fact that mce_no_way_out() iterates over
all MCA banks and possibly overwrites the @msg argument which is
used in the panic printing later.
Change behavior to take the message of only and the (last)
critical MCE it detects.
Reported-by: Derek <denc716@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Link: http://lkml.kernel.org/r/1431936437-25286-3-git-send-email-bp@alien8.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ kamal: backport to 3.13-stable: context ] Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There is NULL pointer dereference possible during statistics update if the route
used for OOTB responce is removed at unfortunate time. If the route exists when
we receive OOTB packet and we finally jump into sctp_packet_transmit() to send
ABORT, but in the meantime route is removed under our feet, we take "no_route"
path and try to update stats with IP_INC_STATS(sock_net(asoc->base.sk), ...).
But sctp_ootb_pkt_new() used to prepare responce packet doesn't call
sctp_transport_set_owner() and therefore there is no asoc associated with this
packet. Probably temporary asoc just for OOTB responces is overkill, so just
introduce a check like in all other places in sctp_packet_transmit(), where
"asoc" is dereferenced.
To reproduce this, one needs to
0. ensure that sctp module is loaded (otherwise ABORT is not generated)
1. remove default route on the machine
2. while true; do
ip route del [interface-specific route]
ip route add [interface-specific route]
done
3. send enough OOTB packets (i.e. HB REQs) from another host to trigger ABORT
responce
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
tcp_fastopen_reset_cipher really cannot be called from interrupt
context. It allocates the tcp_fastopen_context with GFP_KERNEL and
calls crypto_alloc_cipher, which allocates all kind of stuff with
GFP_KERNEL.
Thus, we might sleep when the key-generation is triggered by an
incoming TFO cookie-request which would then happen in interrupt-
context, as shown by enabling CONFIG_DEBUG_ATOMIC_SLEEP:
This patch moves the call to tcp_fastopen_init_key_once to the places
where a listener socket creates its TFO-state, which always happens in
user-context (either from the setsockopt, or implicitly during the
listen()-call)
Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Fixes: 222e83d2e0ae ("tcp: switch tcp_fastopen key generation to net_get_random_once") Signed-off-by: Christoph Paasch <cpaasch@apple.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The lockless lookups can return entry that is unlinked.
Sometimes they get reference before last neigh_cleanup_and_release,
sometimes they do not need reference. Later, any
modification attempts may result in the following problems:
1. entry is not destroyed immediately because neigh_update
can start the timer for dead entry, eg. on change to NUD_REACHABLE
state. As result, entry lives for some time but is invisible
and out of control.
2. __neigh_event_send can run in parallel with neigh_destroy
while refcnt=0 but if timer is started and expired refcnt can
reach 0 for second time leading to second neigh_destroy and
possible crash.
Thanks to Eric Dumazet and Ying Xue for their work and analyze
on the __neigh_event_send change.
Fixes: 767e97e1e0db ("neigh: RCU conversion of struct neighbour") Fixes: a263b3093641 ("ipv4: Make neigh lookups directly in output packet path.") Fixes: 6fd6ce2056de ("ipv6: Do not depend on rt->n in ip6_finish_output2().") Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
PACKET_FANOUT_LB computes f->rr_cur such that it is modulo
f->num_members. It returns the old value unconditionally, but
f->num_members may have changed since the last store. Ensure
that the return value is always < num.
When modifying the logic, simplify it further by replacing the loop
with an unconditional atomic increment.
Fixes: dc99f600698d ("packet: Add fanout support.") Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We need to tell compiler it must not read f->num_members multiple
times. Otherwise testing if num is not zero is flaky, and we could
attempt an invalid divide by 0 in fanout_demux_cpu()
Note bug was present in packet_rcv_fanout_hash() and
packet_rcv_fanout_lb() but final 3.1 had a simple location
after commit 95ec3eb417115fb ("packet: Add 'cpu' fanout policy.")
Fixes: dc99f600698dc ("packet: Add fanout support.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: used davem's backport to 3.14 ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
After the ->set() spinlocks were removed br_stp_set_bridge_priority
was left running without any protection when used via sysfs. It can
race with port add/del and could result in use-after-free cases and
corrupted lists. Tested by running port add/del in a loop with stp
enabled while setting priority in a loop, crashes are easily
reproducible.
The spinlocks around sysfs ->set() were removed in commit: 14f98f258f19 ("bridge: range check STP parameters")
There's also a race condition in the netlink priority support that is
fixed by this change, but it was introduced recently and the fixes tag
covers it, just in case it's needed the commit is: af615762e972 ("bridge: add ageing_time, stp_state, priority over netlink")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Fixes: 14f98f258f19 ("bridge: range check STP parameters") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
->auto_asconf_splist is per namespace and mangled by functions like
sctp_setsockopt_auto_asconf() which doesn't guarantee any serialization.
Also, the call to inet_sk_copy_descendant() was backuping
->auto_asconf_list through the copy but was not honoring
->do_auto_asconf, which could lead to list corruption if it was
different between both sockets.
This commit thus fixes the list handling by using ->addr_wq_lock
spinlock to protect the list. A special handling is done upon socket
creation and destruction for that. Error handlig on sctp_init_sock()
will never return an error after having initialized asconf, so
sctp_destroy_sock() can be called without addrq_wq_lock. The lock now
will be take on sctp_close_sock(), before locking the socket, so we
don't do it in inverse order compared to sctp_addr_wq_timeout_handler().
Instead of taking the lock on sctp_sock_migrate() for copying and
restoring the list values, it's preferred to avoid rewritting it by
implementing sctp_copy_descendant().
Issue was found with a test application that kept flipping sysctl
default_auto_asconf on and off, but one could trigger it by issuing
simultaneous setsockopt() calls on multiple sockets or by
creating/destroying sockets fast enough. This is only triggerable
locally.
Fixes: 9f7d653b67ae ("sctp: Add Auto-ASCONF support (core).") Reported-by: Ji Jianwen <jiji@redhat.com> Suggested-by: Neil Horman <nhorman@tuxdriver.com> Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We saw excessive direct memory compaction triggered by skb_page_frag_refill.
This causes performance issues and add latency. Commit 5640f7685831e0
introduces the order-3 allocation. According to the changelog, the order-3
allocation isn't a must-have but to improve performance. But direct memory
compaction has high overhead. The benefit of order-3 allocation can't
compensate the overhead of direct memory compaction.
This patch makes the order-3 page allocation atomic. If there is no memory
pressure and memory isn't fragmented, the alloction will still success, so we
don't sacrifice the order-3 benefit here. If the atomic allocation fails,
direct memory compaction will not be triggered, skb_page_frag_refill will
fallback to order-0 immediately, hence the direct memory compaction overhead is
avoided. In the allocation failure case, kswapd is waken up and doing
compaction, so chances are allocation could success next time.
alloc_skb_with_frags is the same.
The mellanox driver does similar thing, if this is accepted, we must fix
the driver too.
V3: fix the same issue in alloc_skb_with_frags as pointed out by Eric
V2: make the changelog clearer
Cc: Eric Dumazet <edumazet@google.com> Cc: Chris Mason <clm@fb.com> Cc: Debabrata Banerjee <dbavatar@gmail.com> Signed-off-by: Shaohua Li <shli@fb.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: used davem's backport to 3.14 ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since the addition of sysfs multicast router support if one set
multicast_router to "2" more than once, then the port would be added to
the hlist every time and could end up linking to itself and thus causing an
endless loop for rlist walkers.
So to reproduce just do:
echo 2 > multicast_router; echo 2 > multicast_router;
in a bridge port and let some igmp traffic flow, for me it hangs up
in br_multicast_flood().
Fix this by adding a check in br_multicast_add_router() if the port is
already linked.
The reason this didn't happen before the addition of multicast_router
sysfs entries is because there's a !hlist_unhashed check that prevents
it.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Fixes: 0909e11758bd ("bridge: Add multicast_router sysfs entries") Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
"Running locktests with a large number of iterations resulted in a
client crash. The test run took a while and hasn't finished after close
to 2 hours. The crash happened right after I gave up and killed the test
(after 107m) with Ctrl+C."
The crash happened because a NULL inode pointer got passed into
locks_get_lock_context. The call chain indicates that file_inode(filp)
returned NULL, which means that f_inode was NULL. Since that's zeroed
out in __fput, that suggests that this filp pointer outlived the last
reference.
Looking at the code, that seems possible. We copy the struct file_lock
that's passed in, but if the task is signalled at an inopportune time we
can end up trying to use that file_lock in rpciod context after the process
that requested it has already returned (and possibly put its filp
reference).
Fix this by taking an extra reference to the filp when we allocate the
lock info, and put it in nfs4_lock_release.
Reported-by: Jean Spector <jean@primarydata.com> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If hardware doesn't support DecodeAssist - a feature that provides
more information about the intercept in the VMCB, KVM decodes the
instruction and then updates the next_rip vmcb control field.
However, NRIP support itself depends on cpuid Fn8000_000A_EDX[NRIPS].
Since skip_emulated_instruction() doesn't verify nrip support
before accepting control.next_rip as valid, avoid writing this
field if support isn't present.
Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Laptop with Turks/Thames GPU will freeze if dpm is enabled. It seems
the SMC engine is relying on some state inside the CP engine. CP needs
to chew at least one packet for it to get in good state for dynamic
power management.
This patch simply disabled and re-enable DPM after the ring test which
is enough to avoid the freeze.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Worse yet, reading the error message (the filter again) it says that
there was no error, when there clearly was. The issue is that the
code that checks the input does not check for balanced ops. That is,
having an op between a closed parenthesis and the next token.
This would only cause a warning, and fail out before doing any real
harm, but it should still not caues a warning, and the error reported
should work:
Link: http://lkml.kernel.org/r/20150615175025.7e809215@gandalf.local.home Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Reported-by: Vince Weaver <vincent.weaver@maine.edu> Tested-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
[ luis: backported to 3.16:
- unconditionally decrement cnt as the OP_NOT logic was introduced only
by e12c09cf3087 ("tracing: Add NOT to filtering logic") ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx)
allocated in one DMA-tagged region. While the kernel's heap allocator
should place the overall struct on a cacheline aligned boundary, the 2
buffers contained within may not necessarily align. Consenquently, the ends
of unaligned buffers may not fully flush, and if so, stale data will be left
behind, resulting in small repeating patterns.
This fix aligns the buffers inside the struct.
Note that not all of the data inside caam_rng_ctx necessarily needs to be
DMA-tagged, only the buffers themselves require this. However, a fix would
incur the expense of error-handling bloat in the case of allocation failure.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com> Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Multiple function in asynchronous hashing use a saved-state block,
a.k.a. struct caam_hash_state, which holds a stash of information
between requests (init/update/final). Certain values in this state
block are loaded for processing using an inline-if, and when this
is done, the potential for uninitialized data can pose conflicts.
Therefore, this patch improves initialization of state data to
prevent false assignments using uninitialized data in the state block.
This patch addresses the following traceback, originating in
ahash_final_ctx(), although a problem like this could certainly
exhibit other symptoms:
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com> Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Turns out 1366x768 does not in fact work on this hardware.
Signed-off-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On a HP Envy TouchSmart laptop, there are 2 speakers (main speaker
and subwoofer speaker), 1 headphone and 2 DACs, without this fixup,
the headphone will be assigned to a DAC and the 2 speakers will be
assigned to another DAC, this assignment makes the surround-2.1
channels invalid.
To fix it, here using a DAC/pin preference map to bind the main
speaker to 1 DAC and the subwoofer speaker will be assigned to another
DAC.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When receiving a new iser connect request we serialize
the pending requests by adding the newly created iser connection
to the np accept list and let the login thread process the connect
request one by one (np_accept_wait).
In case we received a disconnect request before the iser_conn
has begun processing (still linked in np_accept_list) we should
detach it from the list and clean it up and not have the login
thread process a stale connection. We do it only when the connection
state is not already terminating (initiator driven disconnect) as
this might lead us to access np_accept_mutex after the np was released
in live shutdown scenarios.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Jenny Falkovich <jennyf@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ luis: backported to 3.16:
- use 'conn_accept_node' instead of 'accept_node' (field renamed by dac6ab305d73 "iser-target: Remove conn_ prefix from struct isert_conn members")
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since commit "2426bd456a6 target: Report correct response ..."
we might get a command with data_size that does not fit to
the number of allocated data sg elements. Given that we rely on
cmd t_data_nents which might be different than the data_size,
we sometimes receive local length error completion. The correct
approach would be to take the command data_size into account when
constructing the ib sg_list.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Jenny Falkovich <jennyf@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
=================================
[ INFO: inconsistent lock state ]
4.1.0-rc7+ #217 Tainted: G O
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/6/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
(ext_devt_lock){+.?...}, at: [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810bf6b1>] __lock_acquire+0x461/0x1e70
[<ffffffff810c1947>] lock_acquire+0xb7/0x290
[<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50
[<ffffffff8143a07d>] blk_alloc_devt+0x6d/0xd0 <-- take the lock in process context
[..]
[<ffffffff810bf64e>] __lock_acquire+0x3fe/0x1e70
[<ffffffff810c00ad>] ? __lock_acquire+0xe5d/0x1e70
[<ffffffff810c1947>] lock_acquire+0xb7/0x290
[<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70
[<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50
[<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70
[<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 <-- take the lock in softirq
[<ffffffff8143bfec>] part_release+0x1c/0x50
[<ffffffff8158edf6>] device_release+0x36/0xb0
[<ffffffff8145ac2b>] kobject_cleanup+0x7b/0x1a0
[<ffffffff8145aad0>] kobject_put+0x30/0x70
[<ffffffff8158f147>] put_device+0x17/0x20
[<ffffffff8143c29c>] delete_partition_rcu_cb+0x16c/0x180
[<ffffffff8143c130>] ? read_dev_sector+0xa0/0xa0
[<ffffffff810e0e0f>] rcu_process_callbacks+0x2ff/0xa90
[<ffffffff810e0dcf>] ? rcu_process_callbacks+0x2bf/0xa90
[<ffffffff81067e2e>] __do_softirq+0xde/0x600
Neil sees this in his tests and it also triggers on pmem driver unbind
for the libnvdimm tests. This fix is on top of an initial fix by Keith
for incorrect usage of mutex_lock() in this path: 2da78092dda1 "block:
Fix dev_t minor allocation lifetime". Both this and 2da78092dda1 are
candidates for -stable.
Fixes: 2da78092dda1 ("block: Fix dev_t minor allocation lifetime") Cc: Keith Busch <keith.busch@intel.com> Reported-by: NeilBrown <neilb@suse.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This seems an use-after-free problem, and the root cause is
zone->wait_table was not set to *NULL* after free it in
try_offline_node.
When hot re-add a node, we will reuse the pgdat of it, so does the zone
struct, and when add pages to the target zone, it will init the zone
first (including the wait_table) if the zone is not initialized. The
judgement of zone initialized is based on zone->wait_table:
static inline bool zone_is_initialized(struct zone *zone)
{
return !!zone->wait_table;
}
so if we do not set the zone->wait_table to *NULL* after free it, the
memory hotplug routine will skip the init of new zone when hot re-add
the node, and the wait_table still points to the freed memory, then we
will access the invalid address when trying to wake up the waiting
people after the i/o operation with the page is done, such as mentioned
above.
Until recently, mac80211 overwrote all the statistics it could
provide when getting called, but it now relies on the struct
having been zeroed by the caller. This was always the case in
nl80211, but wext used a static struct which could even cause
values from one device leak to another.
Using a static struct is OK (as even documented in a comment)
since the whole usage of this function and its return value is
always locked under RTNL. Not clearing the struct for calling
the driver has always been wrong though, since drivers were
free to only fill values they could report, so calling this
for one device and then for another would always have leaked
values from one to the other.
Fix this by initializing the structure in question before the
driver method call.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691
Reported-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Reported-by: Alexander Kaltsas <alexkaltsas@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.
drm: give up on edid retries when i2c bus is not responding
This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).
we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.
Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.
This patch is based on the work, and commit message, by Todd Previte
<tprevite@gmail.com>.
Fixes: 6058bb362818 'ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller' Signed-off-by: Axel Lin <axel.lin@ingics.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Carlo Caione <carlo@caione.org> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1433684009.9134.1.camel@ingics.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The cpumask vp_dev->msix_affinity_masks[info->msix_vector] may contain
staled information when vp_set_vq_affinity() gets called, so clear it
before setting the new cpu bit mask.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[ luis: backported to 3.16:
- file rename: virtio_pci_common.c -> virtio_pci.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
According to the Armada 38x datasheet, the window base address
registers value is set in bits [31:4] of the register and corresponds
to the transaction address bits [47:20].
Therefore, the 32bit base address value should be shifted right by
20bits and left by 4bits, resulting in 16 bit shift right.
The bug as not been noticed yet because if the memory available on
the platform is less than 2GB, then the base address is zero.
When we use 'intel_iommu=igfx_off' to disable translation for the
graphics, and when we discover that the BIOS has misconfigured the DMAR
setup for I/OAT, we use a special DUMMY_DEVICE_DOMAIN_INFO value in
dev->archdata.iommu to indicate that translation is disabled.
With passthrough mode, we were attempting to dereference that as a
normal pointer to a struct device_domain_info when setting up an
identity mapping for the affected device.
This fixes the problem by making device_to_iommu() explicitly check for
the special value and indicate that no IOMMU was found to handle the
devices in question.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit c875d2c1 ("iommu/vt-d: Exclude devices using RMRRs from IOMMU API
domains") prevents certain options for devices with RMRRs. This even
prevents those devices from getting a 1:1 mapping with 'iommu=pt',
because we don't have the code to handle *preserving* the RMRR regions
when moving the device between domains.
There's already an exclusion for USB devices, because we know the only
reason for RMRRs there is a misguided desire to keep legacy
keyboard/mouse emulation running in some theoretical OS which doesn't
have support for USB in its own right... but which *does* enable the
IOMMU.
Add an exclusion for graphics devices too, so that 'iommu=pt' works
there. We should be able to successfully assign graphics devices to
guests too, as long as the initial handling of stolen memory is
reconfigured appropriately. This has certainly worked in the past.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Orphans in the fs tree are cleaned up via open_ctree and subvolume
orphans are cleaned via btrfs_lookup_dentry -- except when a default
subvolume is in use. The name for the default subvolume uses a manual
lookup that doesn't trigger orphan cleanup and needs to trigger it
manually as well. This doesn't apply to the remount case since the
subvolumes are cleaned up by walking the root radix tree.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
fiemap_fill_next_extent returns 0 on success, -errno on error, 1 if this was
the last extent that will fit in user array. If 1 is returned, the return
value may eventually returned to user space, which should not happen, according
to manpage of ioctl.
Signed-off-by: Chengyu Song <csong84@gatech.edu> Reviewed-by: David Sterba <dsterba@suse.cz> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If the clone root was not readonly or the dead flag was set on it, we were
leaving without decrementing the root's send_progress counter (and before
we just incremented it). If a concurrent snapshot deletion was in progress
and ended up being aborted, it would be impossible to later attempt to
delete again the snapshot, since the root's send_in_progress counter could
never go back to 0.
We were also setting clone_sources_to_rollback to i + 1 too early - if we
bailed out because the clone root we got is not readonly or flagged as dead
we ended up later derreferencing a null pointer because we didn't assign
the clone root to sctx->clone_roots[i].root:
for (i = 0; sctx && i < clone_sources_to_rollback; i++)
btrfs_root_dec_send_in_progress(
sctx->clone_roots[i].root);
So just don't increment the send_in_progress counter if the root is readonly
or flagged as dead.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
After we locked the root's root item, a concurrent snapshot deletion
call might have set the dead flag on it. So check if the dead flag
is set and abort if it is, just like we do for the parent root.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Single channel LVDS maxes out at 112 MHz, anything above must be dual
channel. This avoids the need to specify i915.lvds_channel_mode=2 on
all 17" MacBook Pro models with i915 graphics since they had 1920x1200
(193 MHz), plus those 15" pre-retina models which had a resolution
of 1680x1050 (119 MHz) as a BTO option.
Source for 112 MHz limit of single channel LVDS is section 2.3 of:
https://01.org/linuxgraphics/sites/default/files/documentation/ivb_ihd_os_vol3_part4.pdf
v2: Avoid hardcoding 17" models by assuming dual channel LVDS if the
resolution necessitates it, suggested by Jani Nikula.
v3: Fix typo, thanks Joonas Lahtinen.
v4: Split commit in two, suggested by Ville Syrjälä.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Tested-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: included spec reference into the commit message] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Cc: Kamal Mostafa <kamal@canonical.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to disable softirqs because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. The spin locks in br_fdb_update were _bh before commit f8ae737deea1
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit: 292d1398983f ("bridge: add NTF_USE support")
Using local_bh_disable/enable around br_fdb_update() allows us to keep
using the spin_lock/unlock in br_fdb_update for the fast-path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: 292d1398983f ("bridge: add NTF_USE support") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
421b3885bf6d56391297844f43fb7154a6396e12 "udp: ipv4: Add udp early
demux" introduced a regression that allowed sockets bound to INADDR_ANY
to receive packets from multicast groups that the socket had not joined.
For example a socket that had joined 224.168.2.9 could also receive
packets from 225.168.2.9 despite not having joined that group if
ip_early_demux is enabled.
Fix this by calling ip_check_mc_rcu() in udp_v4_early_demux() to verify
that the multicast packet is indeed ours.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com> Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We have two problems in UDP stack related to bogus checksums :
1) We return -EAGAIN to application even if receive queue is not empty.
This breaks applications using edge trigger epoll()
2) Under UDP flood, we can loop forever without yielding to other
processes, potentially hanging the host, especially on non SMP.
This patch is an attempt to make things better.
We might in the future add extra support for rt applications
wanting to better control time spent doing a recv() in a hostile
environment. For example we could validate checksums before queuing
packets in socket receive queue.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit e9ce7cb6b107 ("xen-netback: Factor queue-specific data into queue
struct") introduced a regression when moving queue-specific data into
the queue struct by failing to set the credit_bytes field. This
prevented bandwidth limiting from working. Initialize the field as it
was done before multiqueue support was added.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Mark Salyzyn <salyzyn@android.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
----
v2: switch to sock_flag(sk, SOCK_DEAD) and added net/caif/caif_socket.c
v3: return -ECONNRESET in upstream caller of wait function for SOCK_DEAD Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Callers of the ext_write function are supposed to hold a mutex that
protects the state of the dialed page, but one caller was missing the
lock from the very start, and over time the code has been changed
without following the rule. This patch cleans up the call sites in
violation of the rule.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently, the calibration function that corrects the initial offsets
among multiple devices only works the first time. If the function is
called more than once, the calibration fails and bogus offsets will be
programmed into the devices.
In a well hidden spot, the device documentation tells that trigger indexes
0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work.
This patch fixes the issue by using one of the special triggers during the
recalibration method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
RGMII interfaces come in multiple flavors: RGMII with transmit or
receive internal delay, no delays at all, or delays in both direction.
This change extends the initial check for PHY_INTERFACE_MODE_RGMII to
cover all of these variants since EEE should be allowed for any of these
modes, since it is a property of the RGMII, hence Gigabit PHY capability
more than the RGMII electrical interface and its delays.
Fixes: a59a4d192166 ("phy: add the EEE support and the way to access to the MMD registers") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The code in __netdev_upper_dev_link() has an over-stringent
loop detection logic that actually prevents valid configurations
from working correctly.
In particular, the logic returns an error if an upper device
is already in the list of all upper devices for a given dev.
This particular check seems to be a overzealous as it disallows
perfectly valid configurations. For example:
# ip l a link eth0 name eth0.10 type vlan id 10
# ip l a dev br0 typ bridge
# ip l s eth0.10 master br0
# ip l s eth0 master br0 <--- Will fail
If you switch the last two commands (add eth0 first), then both
will succeed. If after that, you remove eth0 and try to re-add
it, it will fail!
It appears to be enough to simply check adj_list to keeps things
safe.
I've tried stacking multiple devices multiple times in all different
combinations, and either rx_handler registration prevented the stacking
of the device linking cought the error.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
arch/x86/kvm/mmu.c: In function 'kvm_mmu_pte_write':
arch/x86/kvm/mmu.c:4256: error: unknown field 'cr0_wp' specified in initializer
arch/x86/kvm/mmu.c:4257: error: unknown field 'cr4_pae' specified in initializer
arch/x86/kvm/mmu.c:4257: warning: excess elements in union initializer
...
gcc-4.4.4 (at least) has issues when using anonymous unions in
initializers.
Fixes: edc90b7dc4ceef6 ("KVM: MMU: fix SMAP virtualization") Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Vinson Lee <vlee@twopensource.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Jean Delvare [Mon, 20 Apr 2015 09:21:13 +0000 (11:21 +0200)]
thermal: step_wise: Revert optimization
Commit 178c2490b99f898efc06d1ad75cadc84f13021a6 ("thermal: step_wise:
cdev only needs update on a new target state") broke driver acerhdf.
That driver abused the step_wise thermal governor until the bang_bang
governor was available, and the optimization broke this usage model.
Kernels v3.12 to v3.18 are affected. In v3.19 the acerhdf driver was
switched to the bang_bang governor and that solved the problem.
For kernels v3.12 to v3.17, the bang_bang governor isn't available
yet so the easiest fix is to revert the optimization.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Reported-by: Dieter Jurzitza (https://bugzilla.opensuse.org/show_bug.cgi?id=925961) Tested-by: Peter Feuerer <peter@piie.net> Tested-by: Dieter Jurzitza Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In file included from scripts/sortextable.c:194:0:
scripts/sortextable.c: In function `main':
scripts/sortextable.h:176:3: warning: `relocs_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
memset(relocs, 0, relocs_size);
^
scripts/sortextable.h:106:6: note: `relocs_size' was declared here
int relocs_size;
^
In file included from scripts/sortextable.c:192:0:
scripts/sortextable.h:176:3: warning: `relocs_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
memset(relocs, 0, relocs_size);
^
scripts/sortextable.h:106:6: note: `relocs_size' was declared here
int relocs_size;
^
gcc 4.9.1
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Reviewed-by: Jamie Iles <jamie.iles@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Warning:
In file included from scripts/kconfig/zconf.tab.c:2537:0:
scripts/kconfig/menu.c: In function ‘get_symbol_str’:
scripts/kconfig/menu.c:590:18: warning: ‘jump’ may be used uninitialized in this function [-Wmaybe-uninitialized]
jump->offset = strlen(r->s);
Simplifies the test logic because (head && local) means (jump != 0)
and makes GCC happy when checking if the jump pointer was initialized.
Signed-off-by: Peter Kümmel <syntheticpp@gmx.net> Signed-off-by: Michal Marek <mmarek@suse.cz> Cc: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The returned xfrm_state should be hold before unlock xfrm_state_lock,
otherwise the returned xfrm_state maybe be released.
Fixes: c454997e6[{pktgen, xfrm} Introduce xfrm_state_lookup_byspi..] Cc: Fan Du <fan.du@intel.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Fan Du <fan.du@intel.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection") added
kernel stack overflow detection, however it only enabled it conditional
upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never
actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW,
which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so
switch it to using that definition instead.
Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.
Signed-off-by: John D. Blair <johnb@candicontrols.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The driver worked around an error in the MAYA44 USB(+)'s mixer unit
descriptor by aborting before parsing the missing field. However,
aborting parsing too early prevented parsing of the other units
connected to this unit, so the capture mixer controls would be missing.
Fix this by moving the check for this descriptor error after the parsing
of the unit's input pins.
Reported-by: nightmixes <nightmixes@gmail.com> Tested-by: nightmixes <nightmixes@gmail.com> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.
This fixes the touchpad not being detected properly on Asus PU551LA
laptops.
Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If the specified maximum length of the string is a multiple of unsigned
long, we would load one long behind the specified maximum. If that
happens to be in a next page, we can hit a page fault although we were
not expected to.
Fix the off-by-one bug in the test whether we are at the end of the
specified range.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The early_idt_handlers asm code generates an array of entry
points spaced nine bytes apart. It's not really clear from that
code or from the places that reference it what's going on, and
the code only works in the first place because GAS never
generates two-byte JMP instructions when jumping to global
labels.
Clean up the code to generate the correct array stride (member size)
explicitly. This should be considerably more robust against
screw-ups, as GAS will warn if a .fill directive has a negative
count. Using '. =' to advance would have been even more robust
(it would generate an actual error if it tried to move
backwards), but it would pad with nulls, confusing anyone who
tries to disassemble the code. The new scheme should be much
clearer to future readers.
While we're at it, improve the comments and rename the array and
common code.
Binutils may start relaxing jumps to non-weak labels. If so,
this change will fix our build, and we may need to backport this
change.
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Signed-off-by: Jim Bride <jim.bride@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 32f13521ca68bc624ff6effc77f308a52b038bf0
("n_tty: Line copy to user buffer in canonical mode")
changed cannonical mode copying to use copy_to_user
but missed adding the call to the audit framework.
Add in the appropriate functions to get audit support.
Fixes: 32f13521ca68 ("n_tty: Line copy to user buffer in canonical mode") Reported-by: Miloslav Trmač <mitr@redhat.com> Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The subtraction here was using a signed integer and did not have any
bounds checking at all. This commit adds proper bounds checking, made
easy by use of an unsigned integer. This way, a single packet won't be
able to remotely trigger a massive loop, locking up the system for a
considerable amount of time. A PoC follows below, which requires
ozprotocol.h from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
A network supplied parameter was not checked before division, leading to
a divide-by-zero. Since this happens in the softirq path, it leads to a
crash. A PoC follows below, which requires the ozprotocol.h file from
this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Using signed integers, the subtraction between required_size and offset
could wind up being negative, resulting in a memcpy into a heap buffer
with a negative length, resulting in huge amounts of network-supplied
data being copied into the heap, which could potentially lead to remote
code execution.. This is remotely triggerable with a magic packet.
A PoC which obtains DoS follows below. It requires the ozprotocol.h file
from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since elt->length is a u8, we can make this variable a u8. Then we can
do proper bounds checking more easily. Without this, a potentially
negative value is passed to the memcpy inside oz_hcd_get_desc_cnf,
resulting in a remotely exploitable heap overflow with network
supplied data.
This could result in remote code execution. A PoC which obtains DoS
follows below. It requires the ozprotocol.h file from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
usb 7-1: New USB device found, idVendor=046d, idProduct=08ca
...
usb 7-1: Warning! Unlikely big volume range (=3072), cval->res is probably wrong.
usb 7-1: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1
Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.
This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.
Reported-by: Peter Seiderer <ps.report@gmx.net> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Remove extra space between platform prefix and DRIVER_NAME in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This adds support for new Xsens device, Motion Tracker Development Board,
using Xsens' own Vendor ID
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The adis16448, unlike the other chips in this family, in addition to the
hardware channels also sends out the DIAG_STAT register in burst mode
before them. Handle that case by skipping over the first 2 bytes before we
pass the received data to the buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There are a few issues with the burst mode support. For one we don't setup
the rx buffer, so the buffer will never be filled and all samples will read
as the zero. Furthermore the tx buffer has the wrong type, which means the
driver sends the wrong command and not the right data is returned.
The final issue is that in burst mode all channels are transferred. Hence
the length of the transfer length should be the number of hardware
channels * 2 bytes. Currently the driver uses indio_dev->scan_bytes for
this. But if the timestamp channel is enabled the scan_bytes will be larger
than the burst length. Fix this by just calculating the burst length based
on the number of hardware channels.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We unfortunately can't use ~0UL for the scan mask to indicate that the
only valid scan mask is all channels selected. The IIO core needs the exact
mask to work correctly and not a super-set of it. So calculate the masked
based on the channels that are available for a particular device.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Previously, the two voltage channels had the same ID, which didn't cause
conflicts in sysfs only because one channel is named and the other isn't;
this is still violating the spec though, two indexed channels should never
have the same index.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add the scale for the pressure channel, which is currently missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Check length of extended attributes and allocation descriptors when
loading inodes from disk. Otherwise corrupted filesystems could confuse
the code and make the kernel oops.
Reported-by: Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by: Jan Kara <jack@suse.cz>
[bwh: Backported to 3.16: use make_bad_inode() instead of returning error] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Store blocksize in a local variable in udf_fill_inode() since it is used
a lot of times.
Signed-off-by: Jan Kara <jack@suse.cz>
[bwh: Needed for the following fix. Backported to 3.16: adjust context.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Pieter Truter <ptruter@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We used to read file_handle twice. Once to get the amount of extra
bytes, and once to fetch the entire structure.
This may be problematic since we do size verifications only after the
first read, so if the number of extra bytes changes in userspace between
the first and second calls, we'll have an incoherent view of
file_handle.
Instead, read the constant size once, and copy that over to the final
structure without having to re-read it again.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fixes: a87938b2e246b81b4fb ("fs/binfmt_elf.c: fix bug in loading of PIE binaries") Reported-by: James Hogan <james.hogan@imgtec.com> Cc: Michael Davidson <md@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
For mq qdisc, we add per tx queue qdisc to root qdisc
for display purpose, however, that happens too early,
before the new dev->qdisc is finally set, this causes
q->list points to an old root qdisc which is going to be
freed right before assigning with a new one.
Fix this by moving ->attach() after setting dev->qdisc.
For long term, we probably need to clean up the qdisc_graft() code
in case it hides other bugs like this.
Fixes: 95dc19299f74 ("pkt_sched: give visibility to mq slave qdiscs") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
x86 has variable length encoding. x86 JIT compiler is trying
to pick the shortest encoding for given bpf instruction.
While doing so the jump targets are changing, so JIT is doing
multiple passes over the program. Typical program needs 3 passes.
Some very short programs converge with 2 passes. Large programs
may need 4 or 5. But specially crafted bpf programs may hit the
pass limit and if the program converges on the last iteration
the JIT compiler will be producing an image full of 'int 3' insns.
Fix this corner case by doing final iteration over bpf program.
Fixes: 0a14842f5a3c ("net: filter: Just In Time compiler for x86-64") Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Tested-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
