MES provides the driver a call to explicitly flush stale process memory
within the MES to avoid a race condition that results in a fatal
memory violation.
When SET_SHADER_DEBUGGER is called, the driver passes a memory address
that represents a process context address MES uses to keep track of
future per-process calls.
Normally, MES will purge its process context list when the last queue
has been removed. The driver, however, can call SET_SHADER_DEBUGGER
regardless of whether a queue has been added or not.
If SET_SHADER_DEBUGGER has been called with no queues as the last call
prior to process termination, the passed process context address will
still reside within MES.
On a new process call to SET_SHADER_DEBUGGER, the driver may end up
passing an identical process context address value (based on per-process
gpu memory address) to MES but is now pointing to a new allocated buffer
object during KFD process creation. Since the MES is unaware of this,
access of the passed address points to the stale object within MES and
triggers a fatal memory violation.
The solution is for KFD to explicitly flush the process context address
from MES on process termination.
Note that the flush call and the MES debugger calls use the same MES
interface but are separated as KFD calls to avoid conflicting with each
other.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com> Tested-by: Alice Wong <shiwei.wong@amd.com> Reviewed-by: Eric Huang <jinhuieric.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Description]
- When we're in a no plane config, DCN is always asserting
P-State allow
- This creates a scenario where the P-State blackout can start
just as VUPDATE takes place and transitions the DCN config to
a one where one or more HUBP's are active which can result in
underflow
- To fix this issue, force p-state disallow and unforce after
the transition from no planes case -> one or more planes active
Reviewed-by: Samson Tam <samson.tam@amd.com> Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Description]
For mode programming we want to extend the prefetch as much as possible
(up to oto, or as long as we can for equ) if we're not already applying
the 60us prefetch requirement. This is to avoid intermittent underflow
issues during prefetch.
The prefetch extension is applied under the following scenarios:
1. We're in prefetch mode 1 (i.e. we don't support MCLK switch in blank)
2. We're using subvp or drr methods of p-state switch, in which case we
we don't care if prefetch takes up more of the blanking time
Mode programming typically chooses the smallest prefetch time possible
(i.e. highest bandwidth during prefetch) presumably to create margin between
p-states / c-states that happen in vblank and prefetch. Therefore we only
apply this prefetch extension when p-state in vblank is not required (UCLK
p-states take up the most vblank time).
Reviewed-by: Jun Lei <jun.lei@amd.com> Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
we need to refine check_is_responsed() to remove the mutext_lock, each
cmd has a monotonically increasing id, and cmds are executed
sequentially, so we can check the id of the last reponsed cmd, then
determine whether a command has been responded or not.
Signed-off-by: Ming Qian <ming.qian@nxp.com> CC: Xiaolei Wang <xiaolei.wang@windriver.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Releasing the `priv->lock` while iterating the `priv->multicast_list` in
`ipoib_mcast_join_task()` opens a window for `ipoib_mcast_dev_flush()` to
remove the items while in the middle of iteration. If the mcast is removed
while the lock was dropped, the for loop spins forever resulting in a hard
lockup (as was reported on RHEL 4.18.0-372.75.1.el8_6 kernel):
Task A (kworker/u72:2 below) | Task B (kworker/u72:0 below)
-----------------------------------+-----------------------------------
ipoib_mcast_join_task(work) | ipoib_ib_dev_flush_light(work)
spin_lock_irq(&priv->lock) | __ipoib_ib_dev_flush(priv, ...)
list_for_each_entry(mcast, | ipoib_mcast_dev_flush(dev = priv->dev)
&priv->multicast_list, list) |
ipoib_mcast_join(dev, mcast) |
spin_unlock_irq(&priv->lock) |
| spin_lock_irqsave(&priv->lock, flags)
| list_for_each_entry_safe(mcast, tmcast,
| &priv->multicast_list, list)
| list_del(&mcast->list);
| list_add_tail(&mcast->list, &remove_list)
| spin_unlock_irqrestore(&priv->lock, flags)
spin_lock_irq(&priv->lock) |
| ipoib_mcast_remove_list(&remove_list)
(Here, `mcast` is no longer on the | list_for_each_entry_safe(mcast, tmcast,
`priv->multicast_list` and we keep | remove_list, list)
spinning on the `remove_list` of | >>> wait_for_completion(&mcast->done)
the other thread which is blocked |
and the list is still valid on |
it's stack.)
Fix this by keeping the lock held and changing to GFP_ATOMIC to prevent
eventual sleeps.
Unfortunately we could not reproduce the lockup and confirm this fix but
based on the code review I think this fix should address such lockups.
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver unbind time. Among other things, this means that if a
panel is in use that it won't be cleanly powered off at system
shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
A few notes about this fix:
- When adding drm_atomic_helper_shutdown() to the unbind path, I added
it after drm_kms_helper_poll_fini() since that's when other drivers
seemed to have it.
- Technically with a previous patch, ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop"), we don't
actually need to check to see if our "drm" pointer is NULL before
calling drm_atomic_helper_shutdown(). We'll leave the "if" test in,
though, so that this patch can land without any dependencies. It
could potentially be removed later.
- This patch also makes sure to set the drvdata to NULL in the case of
bind errors to make sure that shutdown can't access freed data.
Suggested-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It needs to add missing gcing flag on page during block migration,
in order to garantee migrated data be persisted during checkpoint,
otherwise out-of-order persistency between data and node may cause
data corruption after SPOR.
Similar issue was fixed by commit 2d1fe8a86bf5 ("f2fs: fix to tag
gcing flag on page during file defragment").
The EliteDesk 800 G6 stores a raw WMI string within the ACPI object in its
BIOS corresponding to one instance of HPBIOS_PlatformEvents.Name. This is
evidently a valid way of representing a WMI data item as far as the
Microsoft ACPI-WMI mapper is concerned, but is preventing the driver from
loading.
This seems quite rare, but add support for such strings. Treating this as a
quirk pretty much means adding that support anyway.
Also clean up an oversight in update_numeric_sensor_from_wobj() in which
the result of hp_wmi_strdup() was being used without error checking.
Setting the fan speed is only valid in manual mode; it is not possible
to set the fan's speed in automatic mode.
Return error when attempting to set the fan speed in automatic mode.
Supported media bus codes on the resizer sink pad are identical to the
ISP source pad. The .enum_mbus_code() handler thus delegates the
enumeration to the ISP's operation. This is problematic for two
reasons:
- Format enumeration on the ISP source pad is dependent on the format
configured on the ISP sink pad for the same subdev state (TRY or
ACTIVE), while format enumeration on the resizer sink pad should
return all formats supported by the resizer subdev, regardless of the
ISP configuration.
- Delegating the operation involves creating a fake v4l2_subdev_state on
the stack to pass to the ISP .enum_mbus_code() handler. This gets in
the way of evolution of both the ISP enumeration handler and, more
generally, the V4L2 subdev state infrastructure.
Fix those two issues by implementing format enumeration manually for the
resizer.
In rkisp1_isp_stop() and rkisp1_csi_disable() the driver masks the
interrupts and then apparently assumes that the interrupt handler won't
be running, and proceeds in the stop procedure. This is not the case, as
the interrupt handler can already be running, which would lead to the
ISP being disabled while the interrupt handler handling a captured
frame.
This brings up two issues: 1) the ISP could be powered off while the
interrupt handler is still running and accessing registers, leading to
board lockup, and 2) the interrupt handler code and the code that
disables the streaming might do things that conflict.
It is not clear to me if 2) causes a real issue, but 1) can be seen with
a suitable delay (or printk in my case) in the interrupt handler,
leading to board lockup.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-4-358a2c871a3c@ideasonboard.com Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IRQ handler rkisp1_isr() calls sub-handlers, all of which returns an
irqreturn_t value, but rkisp1_isr() ignores those values and always
returns IRQ_HANDLED.
Fix this by collecting the return values, and returning IRQ_HANDLED or
IRQ_NONE as appropriate.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-2-358a2c871a3c@ideasonboard.com Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In all known platforms the ISP has dedicated IRQ lines, but for some
reason the driver uses IRQF_SHARED.
Supporting IRQF_SHARED properly requires handling interrupts even when
our device is disabled, and the driver does not handle this. To avoid
adding such code, and to be sure the driver won't accidentally be used
in a platform with shared interrupts, let's drop the IRQF_SHARED flag.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-1-358a2c871a3c@ideasonboard.com Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Qualcomm SM8650 platform comes with a DisplayPort controller
with a different base offset than the previous SM8550 SoC,
add support for this in the DisplayPort driver.
When using 32 bit RGB formats, the RGA on the rk3568 produces wrong
colors as the wrong color channels are read or written. The reason is
that the format description for the channel swizzeling is wrong and the
wrong bits are configured. For example, when converting ARGB32 to NV12,
the alpha channel is used as blue channel.. This doesn't happen if the
color format is the same on both sides.
Fix the color_swap settings of the formats to correctly handle 32 bit
RGB formats.
For RGA_COLOR_FMT_XBGR8888, the RGA_COLOR_ALPHA_SWAP bit doesn't have an
effect. Thus, it isn't possible to handle the V4L2_PIX_FMT_XRGB32. Thus,
it is removed from the list of supported formats.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function stk1160_dbg gets called too many times, which causes
the output to get flooded with messages. Since stk1160_dbg uses
printk, it is now replaced with printk_ratelimited.
Suggested-by: Phillip Potter <phil@philpotter.co.uk> Signed-off-by: Ghanshyam Agrawal <ghanshyam1898@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
After reading the code, I think this is what happens:
We have a DSI host defined in the device tree and a DSI peripheral under
that host (i.e. an i2c device using the DSI as data bus doesn't exhibit
this behavior).
The host driver calls mipi_dsi_host_register(), which causes (via a few
functions) mipi_dsi_device_add() to be called for the DSI peripheral. So
now we have a DSI device under the host, but attach hasn't been called.
Normally the probing of the devices continues, and eventually the DSI
peripheral's driver will call mipi_dsi_attach(), attaching the
peripheral.
However, if the host driver's probe encounters an error after calling
mipi_dsi_host_register(), and before the peripheral has called
mipi_dsi_attach(), the host driver will do cleanups and return an error
from its probe function. The cleanups include calling
mipi_dsi_host_unregister().
mipi_dsi_host_unregister() will call two functions for all its DSI
peripheral devices: mipi_dsi_detach() and mipi_dsi_device_unregister().
The latter makes sense, as the device exists, but the former may be
wrong as attach has not necessarily been done.
To fix this, track the attached state of the peripheral, and only detach
from mipi_dsi_host_unregister() if the peripheral was attached.
Note that I have only tested this with a board with an i2c DSI
peripheral, not with a "pure" DSI peripheral.
However, slightly related, the unregister machinery still seems broken.
E.g. if the DSI host driver is unbound, it'll detach and unregister the
DSI peripherals. After that, when the DSI peripheral driver unbound
it'll call detach either directly or using the devm variant, leading to
a crash. And probably the driver will crash if it happens, for some
reason, to try to send a message via the DSI bus.
But that's another topic.
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230921-dsi-detach-fix-v1-1-d0de2d1621d9@ideasonboard.com Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/gpu/drm/drm_framebuffer.c:654 drm_mode_getfb2_ioctl() error: uninitialized symbol 'ret'.
'ret' is possibly not set when there are no errors, causing the error
above. I can't say if that ever happens in real-life, but in any case I
think it is good to initialize 'ret' to 0.
drivers/gpu/drm/drm_file.c:967 drm_show_memory_stats() error: uninitialized symbol 'supported_status'.
'supported_status' is only set in one code path. I'm not familiar with
the code to say if that path will always be ran in real life, but
whether that is the case or not, I think it is good to initialize
'supported_status' to 0 to silence the warning (and possibly fix a bug).
Changing PBN calculation to be more in line with spec. We don't need to
inflate PBN_NATIVE value by the 1.006 margin, since that is already
taken care of in the get_pbn_per_slot function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Generic edp gets mode from edid. However, some panels report incorrect
mode in this way, resulting in glitches on panel. Introduce a new quirk
additional_mode to the generic edid to pick a correct hardcoded mode.
The VFS will not be locking moved directory if its parent does not
change. Change reiserfs rename code to avoid touching renamed directory
if its parent does not change as without locking that can corrupt the
filesystem.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If refcount is less than 1, we should just warn, unlock dentry and
return true, so that the caller doesn't try to do anything else.
Taking care of that leaves the rest of "lockref_put_return() has
failed" case equivalent to "decrement refcount and rejoin the
normal slow path after the point where we grab ->d_lock".
NOTE: lockref_put_return() is strictly a fastpath thing - unlike
the rest of lockref primitives, it does not contain a fallback.
Caller (and it looks like fast_dput() is the only legitimate one
in the entire kernel) has to do that itself. Reasons for
lockref_put_return() failures:
* ->d_lock held by somebody
* refcount <= 0
* ... or an architecture not supporting lockref use of
cmpxchg - sparc, anything non-SMP, config with spinlock debugging...
We could add a fallback, but it would be a clumsy API - we'd have
to distinguish between:
(1) refcount > 1 - decremented, lock not held on return
(2) refcount < 1 - left alone, probably no sense to hold the lock
(3) refcount is 1, no cmphxcg - decremented, lock held on return
(4) refcount is 1, cmphxcg supported - decremented, lock *NOT* held
on return.
We want to return with no lock held in case (4); that's the whole point of that
thing. We very much do not want to have the fallback in case (3) return without
a lock, since the caller might have to retake it in that case.
So it wouldn't be more convenient than doing the fallback in the caller and
it would be very easy to screw up, especially since the test coverage would
suck - no way to test (3) and (4) on the same kernel build.
Reviewed-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The virtual widget example makes use of an undefined SND_SOC_DAPM_NOPM
argument passed to SND_SOC_DAPM_MIXER(). Replace with the correct
SND_SOC_NOPM definition.
In a couple of loops over the all streams, we check the bitmap against
the loop counter. A more correct reference would be, however, the
index of each stream, instead.
This patch corrects the check of bitmaps to the stream index.
Note that this change doesn't fix anything for now; all existing
drivers set up the stream indices properly, hence the loop count is
always equal with the stream index. That said, this change is only
for consistency.
Let's check return value of f2fs_reserve_new_block() in do_recover_data()
rather than letting it fails silently.
Also refactoring check condition on return value of f2fs_reserve_new_block()
as below:
- trigger f2fs_bug_on() only for ENOSPC case;
- use do-while statement to avoid redundant codes;
of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.
There are 2 distinct paths to be considered in qca8k_mdio_register():
- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8ec38 ("net:
mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
treats this well.
- devm_of_mdiobus_register() or anything up to that point fails: it is
the duty of the qca8k driver to release the OF node.
This change addresses the second case by making sure that the OF node
reference is not leaked.
The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As of today, the last MCAM entry was not getting allocated because of
a <= check with the max_bmap count. This patch modifies that and if the
requested entry is greater than the available entries then set it to the
max value.
Currently, if a VF is disabled using the
'ip link set dev $ETHX vf $VF_NUM state disable' command, the VF is still
able to receive traffic.
Fix the behavior of the 'ip link set dev $ETHX vf $VF_NUM state disable'
to completely shutdown the VF's queues making it entirely disabled and
not able to receive or send any traffic.
Modify the behavior of the 'ip link set $ETHX vf $VF_NUM state enable'
command to make a VF do reinitialization bringing the queues back up.
Co-developed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Andrii Staikov <andrii.staikov@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It appears that there is a typo in the code where the nlattr array is
being parsed with policy br_cfm_cc_ccm_tx_policy, but the instance is
being accessed via IFLA_BRIDGE_CFM_CC_RDI_INSTANCE, which is associated
with the policy br_cfm_cc_rdi_policy.
This problem was introduced by commit 2be665c3940d ("bridge: cfm: Netlink
SET configuration Interface.").
Though it seems like a harmless typo since these two enum owns the exact
same value (1 here), it is quite misleading hence fix it by using the
correct enum IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE here.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The system EID (SEID) is an internal EID used by SMC-D to represent the
s390 physical machine that OS is executing on. On s390 architecture, it
predefined by fixed string and part of cpuid and is enabled regardless
of whether underlay device is virtual ISM or platform firmware ISM.
However on non-s390 architectures where SMC-D can be used with virtual
ISM devices, there is no similar information to identify physical
machines, especially in virtualization scenarios. So in such cases, SEID
is forcibly disabled and the user-defined UEID will be used to represent
the communicable space.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com> Reviewed-and-tested-by: Wenjia Zhang <wenjia@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of an incomplete command or a command with a null identifier 2
reject packets will be sent, one with the identifier and one with 0.
Consuming the data of the command will prevent it.
This allows to send a reject packet for each corrupted command in a
multi-command packet.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
when Bluetooth set the event mask and enter suspend, the controller
has hci mode change event coming, it cause controller can not enter
sleep mode. so it should to set the hci mode change event mask before
enter suspend.
Signed-off-by: clancy shang <clancy.shang@quectel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a PA sync socket is closed, the associated hcon is also unlinked
and cleaned up. If there are no other hcons marked with the
HCI_CONN_PA_SYNC flag, HCI_OP_LE_PA_TERM_SYNC is sent to controller.
Between the time of the command and the moment PA sync is terminated
in controller, residual BIGInfo reports might continue to come.
This causes a new PA sync hcon to be added, and a new socket to be
notified to user space.
This commit fixs this by adding a flag on a Broadcast listening
socket to mark when the PA sync child has been closed.
This flag is checked when BIGInfo reports are indicated in
iso_connect_ind, to avoid recreating a hcon and socket if
residual reports arrive before PA sync is terminated.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks
for QCA2066.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a more of a cosmetic fix. The branch will only be taken if
proberesp_ies is set, which implies that beacon_ies is not set unless we
are connected to an AP that just did a channel switch. And, in that case
we should have found the BSS in the internal storage to begin with.
An issue occurred while reading an ELF file in libbpf.c during fuzzing:
Program received signal SIGSEGV, Segmentation fault.
0x0000000000958e97 in bpf_object.collect_prog_relos () at libbpf.c:4206
4206 in libbpf.c
(gdb) bt
#0 0x0000000000958e97 in bpf_object.collect_prog_relos () at libbpf.c:4206
#1 0x000000000094f9d6 in bpf_object.collect_relos () at libbpf.c:6706
#2 0x000000000092bef3 in bpf_object_open () at libbpf.c:7437
#3 0x000000000092c046 in bpf_object.open_mem () at libbpf.c:7497
#4 0x0000000000924afa in LLVMFuzzerTestOneInput () at fuzz/bpf-object-fuzzer.c:16
#5 0x000000000060be11 in testblitz_engine::fuzzer::Fuzzer::run_one ()
#6 0x000000000087ad92 in tracing::span::Span::in_scope ()
#7 0x00000000006078aa in testblitz_engine::fuzzer::util::walkdir ()
#8 0x00000000005f3217 in testblitz_engine::entrypoint::main::{{closure}} ()
#9 0x00000000005f2601 in main ()
(gdb)
scn_data was null at this code(tools/lib/bpf/src/libbpf.c):
if (rel->r_offset % BPF_INSN_SZ || rel->r_offset >= scn_data->d_size) {
The Wi-Fi firmware 29.29.X should use version 2 role info format. FDDT
mechanism version 5 use the same cell members to judge traffic situation,
don't need to add another new format.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20231218061341.51255-2-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a node is only one in port or one out port, address-cells and
size-cells are not required in in-ports and out-ports. And the number
and reg of the port need to be removed.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com> Link: https://lore.kernel.org/r/20231210072633.4243-5-quic_jinlmao@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Upon assembling the array, both kernel and mdadm allow the devices to have event
counter difference of 1, and still consider them as up-to-date.
However, a device whose event count is behind by 1, may in fact not be up-to-date,
and array resync with such a device may cause data corruption.
To avoid this, consult the superblock of the freshest device about the status
of a device, whose event counter is behind by 1.
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver has a logic leak in ring data allocation/free,
where aq_ring_free could be called multiple times on same ring,
if system is under stress and got memory allocation error.
Ring pointer was used as an indicator of failure, but this is
not correct since only ring data is allocated/deallocated.
Ring itself is an array member.
Changing ring allocation functions to return error code directly.
This simplifies error handling and eliminates aq_ring_free
on higher layer.
Fix the values of the ICE_AQ_VSI_Q_OPT_RSS_* registers. Shifting is
already done when the values are used, no need to double shift. Bug was
not discovered earlier since only ICE_AQ_VSI_Q_OPT_RSS_TPLZ (Zero) is
currently used.
Also, rename ICE_AQ_VSI_Q_OPT_RSS_XXX to ICE_AQ_VSI_Q_OPT_RSS_HASH_XXX
for consistency.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Link: https://lore.kernel.org/r/20231213003321.605376-5-ahmed.zaki@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently in directly attached scenario, the phyup event
HISI_PHYE_PHY_UP_PM is notified before .phy_attached is set - this may
cause the phyup work hisi_sas_bytes_dmaed() execution failed and the
attached device will not be found.
To fix it, set .phy_attached before notifing phyup event.
If priority tagging is set in the service parameters of a FLOGI cmpl, then
we update the vmid_flag. In the current logic, if a follow up FLOGI cmpl
updates its service parameters such that priority tagging is no longer set,
then the vmid_flag ends up keeping stale data.
Fix by ensuring we clear the vmid_flag member during lpfc_reinit_vmid, and
check the priority tagging service parameter after reinitialization of the
vmid data structures.
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
fixed clock nodes can't be on the bus because they are missing reg
property. That's why move them to root.
And because it is root it is good to have it as the first node in a file.
Signed-off-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since "dev_search_path" can technically be as large as PATH_MAX,
there was a risk of truncation when copying it and a second string
into "full_path" since it was also PATH_MAX sized. The W=1 builds were
reporting this warning:
drivers/block/rnbd/rnbd-srv.c: In function 'process_msg_open.isra':
drivers/block/rnbd/rnbd-srv.c:616:51: warning: '%s' directive output may be truncated writing up to 254 bytes into a region of size between 0 and 4095 [-Wformat-truncation=]
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~
In function 'rnbd_srv_get_full_path',
inlined from 'process_msg_open.isra' at drivers/block/rnbd/rnbd-srv.c:721:14: drivers/block/rnbd/rnbd-srv.c:616:17: note: 'snprintf' output between 2 and 4351 bytes into a destination of size 4096
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
617 | dev_search_path, dev_name);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
To fix this, unconditionally check for truncation (as was already done
for the case where "%SESSNAME%" was present).
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312100355.lHoJPgKy-lkp@intel.com/ Cc: Md. Haris Iqbal <haris.iqbal@ionos.com> Cc: Jack Wang <jinpu.wang@ionos.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: <linux-block@vger.kernel.org> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev> Acked-by: Jack Wang <jinpu.wang@ionos.com> Link: https://lore.kernel.org/r/20231212214738.work.169-kees@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the driver or firmware is stuck in reset state, don't bother
trying to use adminq commands. This speeds up shutdown and
prevents unnecessary timeouts and error messages.
This includes a bit of rework on ionic_adminq_post_wait()
and ionic_adminq_post_wait_nomsg() to both use
__ionic_adminq_post_wait() which can do the checks needed in
both cases.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't rely on the PCI memory for the devcmd opcode because we
read a 0xff value if the PCI bus is broken, which can cause us
to report a bogus dev_cmd opcode later.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix passing the wrong reference for config_initr on passing the function
pointer, drop the wrong & from at803x_config_intr in the PHY struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
We observe some packets are discarded in ieee80211_rx_handlers_result
function for WCN7850. This is because the way to get multicast/broadcast
indicator with RX_MSDU_END_INFO5_DA_IS_MCBC & info5 is incorrect. It should
use RX_MSDU_END_INFO13_MCAST_BCAST & info13 to get multicast/broadcast
indicator.
Since 'ieee80211_beacon_get()' can return NULL, 'wfx_set_mfp_ap()'
should check the return value before examining skb data. So convert
the latter to return an appropriate error code and propagate it to
return from 'wfx_start_ap()' as well. Compile tested only.
generic_map_{delete,update}_batch() doesn't set uattr->batch.count as
zero before it tries to allocate memory for key. If the memory
allocation fails, the value of uattr->batch.count will be incorrect.
Fix it by setting uattr->batch.count as zero beore batched update or
deletion.
Add a BSS eht_support check before returning EHT phy mode. Without this
patch, there might be an inconsistency where the softmac layer thinks
the BSS is in HE mode, while the FW thinks it is in EHT mode.
In a similar vein to
https://lore.kernel.org/lkml/20220530080842.37024-3-manivannan.sadhasivam@linaro.org/,
the remote processors on sm8350 fail to initialize with the 'correct'
(i.e., specified in downstream) IRQ type. Change this to EDGE_RISING.
Fix the following dt bindings check:
arch/arm64/boot/dts/qcom/sm8450-hdk.dtb: soundwire-controller@31f0000: $nodename:0: 'soundwire-controller@31f0000' does not match '^soundwire(@.*)?$'
from schema $id: http://devicetree.org/schemas/soundwire/qcom,soundwire.yaml#
Fix the following dt bindings check:
arch/arm64/boot/dts/qcom/sm8550-mtp.dtb: soundwire-controller@6ab0000: $nodename:0: 'soundwire-controller@6ab0000' does not match '^soundwire(@.*)?$'
from schema $id: http://devicetree.org/schemas/soundwire/qcom,soundwire.yaml#
Before this change, when operating in polled mode, i.e. no IRQ is
available, every individual C45 access would be hit with a 150us sleep
after the bus access.
For example, on a board with a CN9130 SoC connected to an MV88X3310
PHY, a single C45 read would take around 165us:
root@infix:~$ mdio f212a600.mdio-mii mmd 4:1 bench 0xc003
Performed 1000 reads in 165ms
By replacing the long sleep with a tighter poll loop, we observe a 10x
increase in bus throughput:
root@infix:~$ mdio f212a600.mdio-mii mmd 4:1 bench 0xc003
Performed 1000 reads in 15ms
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20231204100811.2708884-3-tobias@waldekranz.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
