When user send a mbox command whose opcode is CXL_MBOX_OP_CLEAR_LOG and
the in_payload is normal vendor debug log UUID according to
the CXL specification cxl_payload_from_user_allowed() will return
false unexpectedly, Sending mbox cmd operation fails and the kernel
log will print:
Clear Log: input payload not allowed.
All CXL devices that support a debug log shall support the Vendor Debug
Log to allow the log to be accessed through a common host driver, for any
device, all versions of the CXL specification define the same value with
Log Identifier of: 5e1819d9-11a9-400c-811f-d60719403d86
Refer to CXL spec r3.1 Table 8-71
Fix the definition value of DEFINE_CXL_VENDOR_DEBUG_UUID to match the
CXL specification.
[Why/How]
We can miss writing FEC_READY in some cases before LT start, which
violates DP spec. Remove the condition guarding the DPCD write so that
the write happens unconditionally.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
axienet_dma_err_handler can race with axienet_stop in the following
manner:
CPU 1 CPU 2
====================== ==================
axienet_stop()
napi_disable()
axienet_dma_stop()
axienet_dma_err_handler()
napi_disable()
axienet_dma_stop()
axienet_dma_start()
napi_enable()
cancel_work_sync()
free_irq()
Fix this by setting a flag in axienet_stop telling
axienet_dma_err_handler not to bother doing anything. I chose not to use
disable_work_sync to allow for easier backporting.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Link: https://patch.msgid.link/20240903175141.4132898-1-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Adjusted to apply before dmaengine support ] Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Jann points out, PFN mappings are special, because unlike normal
memory mappings, there is no lifetime information associated with the
mapping - it is just a raw mapping of PFNs with no reference counting of
a 'struct page'.
That's all very much intentional, but it does mean that it's easy to
mess up the cleanup in case of errors. Yes, a failed mmap() will always
eventually clean up any partial mappings, but without any explicit
lifetime in the page table mapping itself, it's very easy to do the
error handling in the wrong order.
In particular, it's easy to mistakenly free the physical backing store
before the page tables are actually cleaned up and (temporarily) have
stale dangling PTE entries.
To make this situation less error-prone, just make sure that any partial
pfn mapping is torn down early, before any other error handling.
commit 9636be85cc5b ("x86/hyperv: Fix hyperv_pcpu_input_arg handling when
CPUs go online/offline") introduces a new cpuhp state for hyperv
initialization.
cpuhp_setup_state() returns the state number if state is
CPUHP_AP_ONLINE_DYN or CPUHP_BP_PREPARE_DYN and 0 for all other states.
For the hyperv case, since a new cpuhp state was introduced it would
return 0. However, in hv_machine_shutdown(), the cpuhp_remove_state() call
is conditioned upon "hyperv_init_cpuhp > 0". This will never be true and
so hv_cpu_die() won't be called on all CPUs. This means the VP assist page
won't be reset. When the kexec kernel tries to setup the VP assist page
again, the hypervisor corrupts the memory region of the old VP assist page
causing a panic in case the kexec kernel is using that memory elsewhere.
This was originally fixed in commit dfe94d4086e4 ("x86/hyperv: Fix kexec
panic/hang issues").
Get rid of hyperv_init_cpuhp entirely since we are no longer using a
dynamic cpuhp state and use CPUHP_AP_HYPERV_ONLINE directly with
cpuhp_remove_state().
Cc: stable@vger.kernel.org Fixes: 9636be85cc5b ("x86/hyperv: Fix hyperv_pcpu_input_arg handling when CPUs go online/offline") Signed-off-by: Anirudh Rayabharam (Microsoft) <anirudh@anirudhrb.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Link: https://lore.kernel.org/r/20240828112158.3538342-1-anirudh@anirudhrb.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240828112158.3538342-1-anirudh@anirudhrb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a race condition when accessing the variable
ic->sb->recalc_sector. The function integrity_recalc writes to this
variable when it makes some progress and the function
dm_integrity_map_continue may read this variable concurrently.
One problem is that on 32-bit architectures the 64-bit variable is not
read and written atomically - it may be possible to read garbage if read
races with write.
Another problem is that memory accesses to this variable are not guarded
with memory barriers.
This commit fixes the race - it moves reading ic->sb->recalc_sector to an
earlier place where we hold &ic->endio_wait.lock.
The referenced commit drops bad input, but has false positives.
Tighten the check to avoid these.
The check detects illegal checksum offload requests, which produce
csum_start/csum_off beyond end of packet after segmentation.
But it is based on two incorrect assumptions:
1. virtio_net_hdr_to_skb with VIRTIO_NET_HDR_GSO_TCP[46] implies GSO.
True in callers that inject into the tx path, such as tap.
But false in callers that inject into rx, like virtio-net.
Here, the flags indicate GRO, and CHECKSUM_UNNECESSARY or
CHECKSUM_NONE without VIRTIO_NET_HDR_F_NEEDS_CSUM is normal.
2. TSO requires checksum offload, i.e., ip_summed == CHECKSUM_PARTIAL.
False, as tcp[46]_gso_segment will fix up csum_start and offset for
all other ip_summed by calling __tcp_v4_send_check.
Because of 2, we can limit the scope of the fix to virtio_net_hdr
that do try to set these fields, with a bogus value.
Avoid unnecessary nested min()/max() which results in egregious macro
expansion.
Use clamp_t() as this introduces the least possible expansion, and turn
the {s,u}DIGIT_FITTING() macros into inline functions to avoid the
nested expansion.
This resolves an issue with slackware 15.0 32-bit compilation as
reported by Richard Narron.
Presumably the min/max fixups would be difficult to backport, this patch
should be easier and fix's Richard's problem in 5.15.
Reported-by: Richard Narron <richard@aaazen.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Closes: https://lore.kernel.org/all/4a5321bd-b1f-1832-f0c-cea8694dc5aa@aaazen.com/ Fixes: 867046cc7027 ("minmax: relax check to allow comparison between unsigned arguments and signed constants") Cc: stable@vger.kernel.org Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module eMMC
and SPI flash powered-down initially (in fact it keeps the reset signal
asserted). BIOS_DISABLE_OVERRIDE pin allows to override that signal so
that eMMC and SPI can be used regardless of the state of the signal.
Let's make this GPIO a hog so that it's reserved and locked in the
proper state.
At the same time, make sure the pin is reserved for the hog and cannot
be requested by another node.
In commit 91419ae0420f ("arm64: dts: rockchip: use BCLK to GPIO switch
on rk3399"), an additional pinctrl state was added whose default pinmux
is for 8ch i2s0. However, Puma only has 2ch i2s0. It's been overriding
the pinctrl-0 property but the second property override was missed in
the aforementioned commit.
On Puma, a hardware slider called "BIOS Disable/Normal Boot" can disable
eMMC and SPI to force booting from SD card. Another software-controlled
GPIO is then configured to override this behavior to make eMMC and SPI
available without human intervention. This is currently done in U-Boot
and it was enough until the aforementioned commit.
Indeed, because of this additional not-yet-overridden property, this
software-controlled GPIO is now muxed in a state that does not override
this hardware slider anymore, rendering SPI and eMMC flashes unusable.
Let's override the property with the 2ch pinmux to fix this.
Fixes: 91419ae0420f ("arm64: dts: rockchip: use BCLK to GPIO switch on rk3399") Cc: stable@vger.kernel.org Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de> Link: https://lore.kernel.org/r/20240731-puma-emmc-6-v1-1-4e28eadf32d0@cherry.de Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new endpoint using the IP of the initial subflow has been recently
added to increase the code coverage. But it breaks the test when using
old kernels not having commit 86e39e04482b ("mptcp: keep track of local
endpoint still available for each msk"), e.g. on v5.15.
Similar to commit d4c81bbb8600 ("selftests: mptcp: join: support local
endpoint being tracked or not"), it is possible to add the new endpoint
conditionally, by checking if "mptcp_pm_subflow_check_next" is present
in kallsyms: this is not directly linked to the commit introducing this
symbol but for the parent one which is linked anyway. So we can know in
advance what will be the expected behaviour, and add the new endpoint
only when it makes sense to do so.
In remove_anno_list_by_saddr(running on CPU2), after leaving the critical
zone protected by "pm.lock", the entry will be released, which leads to the
occurrence of uaf in the mptcp_pm_del_add_timer(running on CPU1).
Keeping a reference to add_timer inside the lock, and calling
sk_stop_timer_sync() with this reference, instead of "entry->add_timer".
Move list_del(&entry->list) to mptcp_pm_del_add_timer and inside the pm lock,
do not directly access any members of the entry outside the pm lock, which
can avoid similar "entry->x" uaf.
Fixes: 00cfd77b9063 ("mptcp: retransmit ADD_ADDR when timeout") Cc: stable@vger.kernel.org Reported-and-tested-by: syzbot+f3a31fb909db9b2a5c4d@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=f3a31fb909db9b2a5c4d Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Edward Adam Davis <eadavis@qq.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://patch.msgid.link/tencent_7142963A37944B4A74EF76CD66EA3C253609@qq.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The panasonic laptop code in various places uses the SINF array with index
values of 0 - SINF_CUR_BRIGHT(0x0d) without checking that the SINF array
is big enough.
Not all panasonic laptops have this many SINF array entries, for example
the Toughbook CF-18 model only has 10 SINF array entries. So it only
supports the AC+DC brightness entries and mute.
Check that the SINF array has a minimum size which covers all AC+DC
brightness entries and refuse to load if the SINF array is smaller.
For higher SINF indexes hide the sysfs attributes when the SINF array
does not contain an entry for that attribute, avoiding show()/store()
accessing the array out of bounds and add bounds checking to the probe()
and resume() code accessing these.
Fixes: e424fb8cc4e6 ("panasonic-laptop: avoid overflow in acpi_pcc_hotkey_add()") Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20240909113227.254470-1-hdegoede@redhat.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-ENODEV is used to signify that there is no zap shader for the platform,
and the CPU can directly take the GPU out of secure mode. We want to
use this return code when there is no zap-shader node. But not when
there is, but without a firmware-name property. This case we want to
treat as-if the needed fw is not found.
Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/604564/ Signed-off-by: Sasha Levin <sashal@kernel.org>
Add SAM client device nodes for the Surface Laptop Go 3. It seems to use
the same SAM client devices as the Surface Laptop Go 1 and 2, so re-use
their node group.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20240811131948.261806-3-luzmaximilian@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When merging files without trailing newlines at the end of the file, two
config fragments end up at the same row if file1.config doens't have a
trailing newline at the end of the file.
GT7868Q has incorrect data in the report and needs a fixup.
The change enables haptic touchpad on Lenovo ThinkBook 13x Gen 4
and has been tested on the device.
Unlink changes the link count on the target inode. POSIX mandates that
the ctime must also change when this occurs.
According to https://pubs.opengroup.org/onlinepubs/9699919799/functions/unlink.html:
"Upon successful completion, unlink() shall mark for update the last data
modification and last file status change timestamps of the parent
directory. Also, if the file's link count is not 0, the last file status
change timestamp of the file shall be marked for update."
Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: David Sterba <dsterba@suse.com>
[ add link to the opengroup docs ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pci_request_regions is called to apply for PCI I/O and memory resources
when the driver is initialized, Therefore, when the driver is uninstalled,
pci_release_regions should be used to release PCI I/O and memory resources
instead of pci_release_mem_regions is used to release memory reasouces
only.
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is due to virt_addr_valid() using high_memory before it is set.
high_memory is set in mem_init() using max_low_pfn, but max_low_pfn
is available long before, it is set in mem_topology_setup(). So just
like commit daa9ada2093e ("powerpc/mm: Fix boot crash with FLATMEM")
moved the setting of max_mapnr immediately after the call to
mem_topology_setup(), the same can be done for high_memory.
Apart from the standard "configurations", "interfaces" and "alternate
interface settings" in USB, iOS devices also have a notion of
"modes". In different modes, the device exposes a different set of
available configurations.
Depending on the iOS version, and depending on the current mode, the
length and contents of the carrier state control message differs:
* 1 byte (seen on iOS 4.2.1, 8.4):
* 03: carrier off (mode 0)
* 04: carrier on (mode 0)
* 3 bytes (seen on iOS 10.3.4, 15.7.6):
* 03 03 03: carrier off (mode 0)
* 04 04 03: carrier on (mode 0)
* 4 bytes (seen on iOS 16.5, 17.6):
* 03 03 03 00: carrier off (mode 0)
* 04 03 03 00: carrier off (mode 1)
* 06 03 03 00: carrier off (mode 4)
* 04 04 03 04: carrier on (mode 0 and 1)
* 06 04 03 04: carrier on (mode 4)
Before this change, the driver always used the first byte of the
response to determine carrier state.
From this larger sample, the first byte seems to indicate the number of
available USB configurations in the current mode (with the exception of
the default mode 0), and in some cases (namely mode 1 and 4) does not
correlate with the carrier state.
Previous logic erroneously counted `04 03 03 00` as "carrier on" and
`06 04 03 04` as "carrier off" on iOS versions that support mode 1 and
mode 4 respectively.
Only modes 0, 1 and 4 expose the USB Ethernet interfaces necessary for
the ipheth driver.
Check the second byte of the control message where possible, and fall
back to checking the first byte on older iOS versions.
Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On iPhone 15 Pro Max one can observe periodic URBs with no payload
on the "bulk in" (RX) endpoint. These don't seem to do anything
meaningful. Reproduced on iOS 17.5.1 and 17.6.
This behaviour isn't observed on iPhone 11 on the same iOS version. The
nature of these zero-length URBs is so far unknown.
Drop RX URBs with no payload.
Signed-off-by: Foster Snowhill <forst@pen.gy> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rx URB length was already checked in ipheth_rcvbulk_callback_legacy()
and ipheth_rcvbulk_callback_ncm(), depending on the current mode.
The check in ipheth_rcvbulk_callback() was thus mostly a duplicate.
The only place in ipheth_rcvbulk_callback() where we care about the URB
length is for the initial control frame. These frames are always 4 bytes
long. This has been checked as far back as iOS 4.2.1 on iPhone 3G.
Remove the extraneous URB length check. For control frames, check for
the specific 4-byte length instead.
Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. Prefer kzalloc() over kcalloc()
See memory-allocation.rst which says: "to be on the safe side it's
best to use routines that set memory to zero, like kzalloc()"
2. Drop dev_err() for u_boot_env_add_cells() fail
It can fail only on -ENOMEM. We don't want to print error then.
3. Add extra "crc32_addr" variable
It makes code reading header's crc32 easier to understand / review.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20231221173421.13737-5-zajec5@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8679e8b4a1eb ("nvmem: u-boot-env: error if NVMEM device is too small") Signed-off-by: Sasha Levin <sashal@kernel.org>
This is required by layouts that need to read whole NVMEM content. It's
especially useful for NVMEM devices without hardcoded layout (like
U-Boot environment data block).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20231221173421.13737-2-zajec5@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8679e8b4a1eb ("nvmem: u-boot-env: error if NVMEM device is too small") Signed-off-by: Sasha Levin <sashal@kernel.org>
The cfg pointer is set before reading the channel number that the
configuration should point to. This causes configurations to be shifted
by one channel.
For example setting bipolar to the first channel defined in the DT will
cause bipolar mode to be active on the second defined channel.
Fix by moving the cfg pointer setting after reading the channel number.
Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels") Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://patch.msgid.link/20240806085133.114547-1-dumitru.ceclan@analog.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using the generic firmware data access functions from property.h
provides a number of advantages:
1) Works with different firmware types.
2) Doesn't provide a 'bad' example for new IIO drivers.
3) Lets us use the new _scoped() loops with automatic reference count
cleanup for fwnode_handle
Similar to recently propose for_each_child_of_node_scoped() this
new version of the loop macro instantiates a new local
struct fwnode_handle * that uses the __free(fwnode_handle) auto
cleanup handling so that if a reference to a node is held on early
exit from the loop the reference will be released. If the loop
runs to completion, the child pointer will be NULL and no action will
be taken.
The reason this is useful is that it removes the need for
fwnode_handle_put() on early loop exits. If there is a need
to retain the reference, then return_ptr(child) or no_free_ptr(child)
may be used to safely disable the auto cleanup.
Useful where the fwnode_handle was obtained from a call such as
fwnode_find_reference() as it will safely do nothing if IS_ERR() is true
and will automatically release the reference on the variable leaving
scope.
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following error caused by hci_conn being freed while
hcy_acl_create_conn_sync is pending:
==================================================================
BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0xa7/0x2e0
Write of size 2 at addr ffff888002ae0036 by task kworker/u3:0/848
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 783bf5d09f86 ("spi: spi-fsl-lpspi: limit PRESCALE bit in
TCR register") doesn't implement the prescaler maximum as intended.
The maximum allowed value for i.MX93 should be 1 and for i.MX7ULP
it should be 7. So this needs also a adjustment of the comparison
in the scldiv calculation.
Fixes: 783bf5d09f86 ("spi: spi-fsl-lpspi: limit PRESCALE bit in TCR register") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://patch.msgid.link/20240905111537.90389-1-wahrenst@gmx.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have 2 threads that are using the same file descriptor and one of
them is doing direct IO writes while the other is doing fsync, we have a
race where we can end up either:
1) Attempt a fsync without holding the inode's lock, triggering an
assertion failures when assertions are enabled;
2) Do an invalid memory access from the fsync task because the file private
points to memory allocated on stack by the direct IO task and it may be
used by the fsync task after the stack was destroyed.
The race happens like this:
1) A user space program opens a file descriptor with O_DIRECT;
2) The program spawns 2 threads using libpthread for example;
3) One of the threads uses the file descriptor to do direct IO writes,
while the other calls fsync using the same file descriptor.
4) Call task A the thread doing direct IO writes and task B the thread
doing fsyncs;
5) Task A does a direct IO write, and at btrfs_direct_write() sets the
file's private to an on stack allocated private with the member
'fsync_skip_inode_lock' set to true;
6) Task B enters btrfs_sync_file() and sees that there's a private
structure associated to the file which has 'fsync_skip_inode_lock' set
to true, so it skips locking the inode's VFS lock;
7) Task A completes the direct IO write, and resets the file's private to
NULL since it had no prior private and our private was stack allocated.
Then it unlocks the inode's VFS lock;
8) Task B enters btrfs_get_ordered_extents_for_logging(), then the
assertion that checks the inode's VFS lock is held fails, since task B
never locked it and task A has already unlocked it.
Another problem here is if task B grabs the private pointer and then uses
it after task A has finished, since the private was allocated in the stack
of task A, it results in some invalid memory access with a hard to predict
result.
This issue, triggering the assertion, was observed with QEMU workloads by
two users in the Link tags below.
Fix this by not relying on a file's private to pass information to fsync
that it should skip locking the inode and instead pass this information
through a special value stored in current->journal_info. This is safe
because in the relevant section of the direct IO write path we are not
holding a transaction handle, so current->journal_info is NULL.
The following C program triggers the issue:
$ cat repro.c
/* Get the O_DIRECT definition. */
#ifndef _GNU_SOURCE
#define _GNU_SOURCE
#endif
Usually the race is triggered within less than 1 second. A test case for
fstests will follow soon.
Reported-by: Paulo Dias <paulo.miguel.dias@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=219187 Reported-by: Andreas Jahn <jahn-andi@web.de> Link: https://bugzilla.kernel.org/show_bug.cgi?id=219199 Reported-by: syzbot+4704b3cc972bd76024f1@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/00000000000044ff540620d7dee2@google.com/ Fixes: 939b656bc8ab ("btrfs: fix corruption after buffer fault in during direct IO append write") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So it turns out that we have to do two passes of
pti_clone_entry_text(), once before initcalls, such that device and
late initcalls can use user-mode-helper / modprobe and once after
free_initmem() / mark_readonly().
Now obviously mark_readonly() can cause PMD splits, and
pti_clone_pgtable() doesn't like that much.
Allow the late clone to split PMDs so that pagetables stay in sync.
[peterz: Changelog and comments] Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Guenter Roeck <linux@roeck-us.net> Link: https://lkml.kernel.org/r/20240806184843.GX37996@noisy.programming.kicks-ass.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The membarrier system call requires a full memory barrier after storing
to rq->curr, before going back to user-space. The barrier is only
needed when switching between processes: the barrier is implied by
mmdrop() when switching from kernel to userspace, and it's not needed
when switching from userspace to kernel.
Rely on the feature/mechanism ARCH_HAS_MEMBARRIER_CALLBACKS and on the
primitive membarrier_arch_switch_mm(), already adopted by the PowerPC
architecture, to insert the required barrier.
When two UBLK_CMD_START_USER_RECOVERY commands are submitted, the
first one sets 'ubq->ubq_daemon' to NULL, and the second one triggers
WARN in ublk_queue_reinit() and subsequently a NULL pointer dereference
issue.
Fix it by adding the check in ublk_ctrl_start_recovery() and return
immediately in case of zero 'ub->nr_queues_ready'.
It makes no sense to restrict physical memory size because of linear
mapping size constraints when there is no linear mapping, so only do
that when mmu is enabled.
If smb2_set_path_attr() is called with a valid @cfile and returned
-EINVAL, we need to call cifs_get_writable_path() again as the
reference of @cfile was already dropped by previous smb2_compound_op()
call.
Fixes: 71f15c90e785 ("smb: client: retry compound request without reusing lease") Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Amit Pundir reports that audio and USB-C host mode stops working if the
gcc_usb30_prim_master_clk_src clk is registered and
clk_rcg2_shared_init() parks it on XO. Skip parking this clk at
registration time to fix those issues.
Partially revert commit 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon
registration") by skipping the parking bit for this clk, but keep the
part where we cache the config register. That's still necessary to
figure out the true parent of the clk at registration time.
Fixes: 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon registration") Fixes: 929c75d57566 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable") Cc: Konrad Dybcio <konradybcio@kernel.org> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Taniya Das <quic_tdas@quicinc.com> Reported-by: Amit Pundir <amit.pundir@linaro.org> Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20240819233628.2074654-3-swboyd@chromium.org Tested-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The QUPs aren't shared in a way that requires parking the RCG at an
always on parent in case some other entity turns on the clk. The
hardware is capable of setting a new frequency itself with the DFS mode,
so parking is unnecessary. Furthermore, there aren't any GDSCs for these
devices, so there isn't a possibility of the GDSC turning on the clks
for housekeeping purposes.
This wasn't a problem to mark these clks shared until we started parking
shared RCGs at clk registration time in commit 01a0a6cc8cfd ("clk: qcom:
Park shared RCGs upon registration"). Parking at init is actually
harmful to the UART when earlycon is used. If the device is pumping out
data while the frequency changes you'll see garbage on the serial
console until the driver can probe and actually set a proper frequency.
Revert the QUP part of commit 929c75d57566 ("clk: qcom: gcc-sm8550: Mark
RCGs shared where applicable") so that the QUPs don't get parked during
clk registration and break UART operations.
Fixes: 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon registration") Fixes: 929c75d57566 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable") Cc: Konrad Dybcio <konradybcio@kernel.org> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Taniya Das <quic_tdas@quicinc.com> Reported-by: Amit Pundir <amit.pundir@linaro.org> Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20240819233628.2074654-2-swboyd@chromium.org Tested-by: Amit Pundir <amit.pundir@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the LRCLK polarity for sun8i-h3 and sun50i-h6 in i2s mode
which was wrongly inverted.
The LRCLK was being set in reversed logic compared to the DAI format:
inverted LRCLK for SND_SOC_DAIFMT_IB_NF and SND_SOC_DAIFMT_NB_NF; normal
LRCLK for SND_SOC_DAIFMT_IB_IF and SND_SOC_DAIFMT_NB_IF. Such reversed
logic applies properly for DSP_A, DSP_B, LEFT_J and RIGHT_J modes but
not for I2S mode, for which the LRCLK signal results reversed to what
expected on the bus. The issue is due to a misinterpretation of the
LRCLK polarity bit of the H3 and H6 i2s controllers. Such bit in this
case does not mean "0 => normal" or "1 => inverted" according to the
expected bus operation, but it means "0 => frame starts on low edge" and
"1 => frame starts on high edge" (from the User Manuals).
This commit fixes the LRCLK polarity by setting the LRCLK polarity bit
according to the selected bus mode and renames the LRCLK polarity bit
definition to avoid further confusion.
Fixes: dd657eae8164 ("ASoC: sun4i-i2s: Fix the LRCK polarity") Fixes: 73adf87b7a58 ("ASoC: sun4i-i2s: Add support for H6 I2S") Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com> Link: https://patch.msgid.link/20240801-asoc-fix-sun4i-i2s-v2-1-a8e4e9daa363@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SOF topology loading function sets the device name for the platform
component link. This should be unset when unloading the topology,
otherwise a machine driver unbind/bind or reprobe would complain about
an invalid component as having both its component name and of_node set:
mt8186_mt6366 sound: ASoC: Both Component name/of_node are set for AFE_SOF_DL1
mt8186_mt6366 sound: error -EINVAL: Cannot register card
mt8186_mt6366 sound: probe with driver mt8186_mt6366 failed with error -22
This happens with machine drivers that set the of_node separately.
Clear the SOF link platform name in the topology unload callback.
Fixes: 311ce4fe7637 ("ASoC: SOF: Add support for loading topologies") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Link: https://patch.msgid.link/20240821041006.2618855-1-wenst@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a drive is unable to create IO queues on the initial probe, a
subsequent reset will need to allocate the tagset if IO queue creation
is successful. Without this, blk_mq_update_nr_hw_queues will crash on a
bad pointer due to the invalid tagset.
Fixes: eac3ef262941f62 ("nvme-pci: split the initial probe from the rest path") Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When Tegra audio drivers are built as part of the kernel image,
TIMEOUT_ERR is observed from cbb-fabric. Following is seen on
Jetson AGX Orin during boot:
These errors happen when MVC device, which is a child of AHUB
device, tries to access its device registers. This happens as
part of call tegra210_mvc_reset_vol_settings() in MVC device
probe().
The root cause of this problem is, the child MVC device gets
probed before the AHUB clock gets enabled. The AHUB clock is
enabled in runtime PM resume of parent AHUB device and due to
the wrong sequence of pm_runtime_enable() in AHUB driver,
runtime PM resume doesn't happen for AHUB device when MVC makes
register access.
Fix this by calling pm_runtime_enable() for parent AHUB device
before of_platform_populate() in AHUB driver. This ensures that
clock becomes available when MVC makes register access.
After building the VDSO, there is a verification that it contains
no dynamic relocation, see commit aff69273af61 ("vdso: Improve
cmd_vdso_check to check all dynamic relocations").
This verification uses readelf -r and doesn't work if rela sections
are discarded.
Patch series "Reimplement huge pages without hugepd on powerpc (8xx, e500,
book3s/64)", v7.
Unlike most architectures, powerpc 8xx HW requires a two-level pagetable
topology for all page sizes. So a leaf PMD-contig approach is not
feasible as such.
Possible sizes on 8xx are 4k, 16k, 512k and 8M.
First level (PGD/PMD) covers 4M per entry. For 8M pages, two PMD entries
must point to a single entry level-2 page table. Until now that was done
using hugepd. This series changes it to use standard page tables where
the entry is replicated 1024 times on each of the two pagetables refered
by the two associated PMD entries for that 8M page.
For e500 and book3s/64 there are less constraints because it is not tied
to the HW assisted tablewalk like on 8xx, so it is easier to use leaf PMDs
(and PUDs).
On e500 the supported page sizes are 4M, 16M, 64M, 256M and 1G. All at
PMD level on e500/32 (mpc85xx) and mix of PMD and PUD for e500/64. We
encode page size with 4 available bits in PTE entries. On e300/32 PGD
entries size is increases to 64 bits in order to allow leaf-PMD entries
because PTE are 64 bits on e500.
On book3s/64 only the hash-4k mode is concerned. It supports 16M pages as
cont-PMD and 16G pages as cont-PUD. In other modes (radix-4k, radix-6k
and hash-64k) the sizes match with PMD and PUD sizes so that's just leaf
entries. The hash processing make things a bit more complex. To ease
things, __hash_page_huge() is modified to bail out when DIRTY or ACCESSED
bits are missing, leaving it to mm core to fix it.
This patch (of 23):
The nohash HTW_IBM (Hardware Table Walk) code is unused since support for
A2 was removed in commit fb5a515704d7 ("powerpc: Remove platforms/ wsp and
associated pieces") (2014).
The remaining supported CPUs use either no HTW (data_tlb_miss_bolted), or
the e6500 HTW (data_tlb_miss_e6500).
Update PLL offsets to DEFAULT_EVO to configure MDIO to 800MHz.
The incorrect clock frequency leads to an incorrect MDIO clock. This,
in turn, affects the MDIO hardware configurations as the divider is
calculated from the MDIO clock frequency. If the clock frequency is
not as expected, the MDIO register fails due to the generation of an
incorrect MDIO frequency.
This issue is critical as it results in incorrect MDIO configurations
and ultimately leads to the MDIO function not working. This results in
a complete feature failure affecting all Ethernet PHYs. Specifically,
Ethernet will not work on IPQ9574 due to this issue.
Currently, the clock frequency is set to CLK_ALPHA_PLL_TYPE_DEFAULT.
However, this setting does not yield the expected clock frequency.
To rectify this, we need to change this to CLK_ALPHA_PLL_TYPE_DEFAULT_EVO.
This modification ensures that the clock frequency aligns with our
expectations, thereby resolving the MDIO register failure and ensuring
the proper functioning of the Ethernet on IPQ9574.
Missing src scatterlist nent assignment in rsa decrypt function.
Removing all unneeded assignment and use nents value from req->src
instead.
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hardware expects RSA input plain/ciphertext to be 32-bit aligned.
Set fixed length for preallocated buffer to the maximum supported
keysize of the hardware and shift input text accordingly.
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
qc->result_tf contents are only valid when the ATA_QCFLAG_RTF_FILLED flag
is set. The ATA_QCFLAG_RTF_FILLED flag should be always set for commands
that failed or for commands that have the ATA_QCFLAG_RESULT_TF flag set.
Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Link: https://lore.kernel.org/r/20240702024735.1152293-8-ipylypiv@google.com Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch tries to works around erratum DS80000789E 6 of the
mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old, already processed CAN frames or new, incompletely written CAN
frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp [1] of the last
valid received CAN frame and compare against the timestamp of every
received CAN frame. If an old CAN frame is detected, abort the
iteration and mark the number of valid CAN frames as processed in the
chip by incrementing the FIFO's tail index.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames [2] are not recognized but then processed. These CAN frames
have the correct data and time stamps, but the DLC has not yet been
updated.
[1] As the raw timestamp overflows every 107 seconds (at the usual
clock rate of 40 MHz) convert it to nanoseconds with the
timecounter framework and use this to detect stale CAN frames.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mcp251xfd chip is configured to provide a timestamp with each
received and transmitted CAN frame. The timestamp is derived from the
internal free-running timer, which can also be read from the TBC
register via SPI. The timer is 32 bits wide and is clocked by the
external oscillator (typically 20 or 40 MHz).
To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw"
for short.
Using the timecounter framework, the "ts_raw" is converted to 64 bit
nanoseconds since the epoch. This is what we call "timestamp".
This is a preparation for the next patches which use the "timestamp"
to work around a bug where so far only the "ts_raw" is used.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a preparatory patch to work around erratum DS80000789E 6 of
the mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
When handling the RX interrupt, the driver iterates over all pending
FIFOs (which are implemented as ring buffers in hardware) and reads
the FIFO header index from the RX FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN frames that were already processed, or new, incompletely
written CAN frames to be (re-)processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len().
The mcp251xfd_handle_rxif_ring() function reads the received CAN
frames from the chip, iterates over them and pushes them into the
network stack. Prepare that the iteration can be stopped if an old CAN
frame is detected. The actual code to detect old or incomplete frames
and abort will be added in the next patch.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sending the UINC messages followed by incrementing the tail pointer
will be called in more than one place in upcoming patches, so factor
this out into a separate function.
Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a
"len" of 0.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In a review discussion of the changes to support vCPU hotplug where
a check was added on the GICC being enabled if was online, it was
noted that there is need to map back to the cpu and use that to index
into a cpumask. As such, a valid ID is needed.
If an MPIDR check fails in acpi_map_gic_cpu_interface() it is possible
for the entry in cpu_madt_gicc[cpu] == NULL. This function would
then cause a NULL pointer dereference. Whilst a path to trigger
this has not been established, harden this caller against the
possibility.
If acpi_processor_get_info() returned an error, pr and the associated
pr->throttling.shared_cpu_map were leaked.
The unwind code was in the wrong order wrt to setup, relying on
some unwind actions having no affect (clearing variables that were
never set etc). That makes it harder to reason about so reorder
and add appropriate labels to only undo what was actually set up
in the first place.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240529133446.28446-6-Jonathan.Cameron@huawei.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rafael observed [1] that returning 0 from processor_add() will result in
acpi_default_enumeration() being called which will attempt to create a
platform device, but that makes little sense when the processor is known
to be not available. So just return the error code from acpi_processor_get_info()
instead.
On a ~2000 CPU powerpc system, hard lockups have been observed in the
workqueue code when stop_machine runs (in this case due to CPU hotplug).
This is due to lots of CPUs spinning in multi_cpu_stop, calling
touch_nmi_watchdog() which ends up calling wq_watchdog_touch().
wq_watchdog_touch() writes to the global variable wq_watchdog_touched,
and that can find itself in the same cacheline as other important
workqueue data, which slows down operations to the point of lockups.
In the case of the following abridged trace, worker_pool_idr was in
the hot line, causing the lockups to always appear at idr_find.
watchdog: CPU 1125 self-detected hard LOCKUP @ idr_find
Call Trace:
get_work_pool
__queue_work
call_timer_fn
run_timer_softirq
__do_softirq
do_softirq_own_stack
irq_exit
timer_interrupt
decrementer_common_virt
* interrupt: 900 (timer) at multi_cpu_stop
multi_cpu_stop
cpu_stopper_thread
smpboot_thread_fn
kthread
Fix this by having wq_watchdog_touch() only write to the line if the
last time a touch was recorded exceeds 1/4 of the watchdog threshold.
Reported-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 5da226dbfce3 ("mm: skip CMA pages when they are not
available") and b7108d66318a ("Multi-gen LRU: skip CMA pages when they are
not eligible").
lruvec->lru_lock is highly contended and is held when calling
isolate_lru_folios. If the lru has a large number of CMA folios
consecutively, while the allocation type requested is not MIGRATE_MOVABLE,
isolate_lru_folios can hold the lock for a very long time while it skips
those. For FIO workload, ~150million order=0 folios were skipped to
isolate a few ZONE_DMA folios [1]. This can cause lockups [1] and high
memory pressure for extended periods of time [2].
Ole reported that event->mmap_mutex is strictly insufficient to
serialize the AUX buffer, add a per RB mutex to fully serialize it.
Note that in the lock order comment the perf_event::mmap_mutex order
was already wrong, that is, it nesting under mmap_lock is not new with
this patch.
Fixes: 45bfb2e50471 ("perf: Add AUX area to ring buffer for raw data streams") Reported-by: Ole <ole@binarygecko.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/clocksource/timer-of.c: In function ‘timer_of_irq_exit’:
drivers/clocksource/timer-of.c:29:46: error: passing argument 2 of
‘free_percpu_irq’ from pointer to non-enclosed address space
29 | free_percpu_irq(of_irq->irq, clkevt);
| ^~~~~~
In file included from drivers/clocksource/timer-of.c:8:
./include/linux/interrupt.h:201:43: note: expected ‘__seg_gs void *’
but argument is of type ‘struct clock_event_device *’
201 | extern void free_percpu_irq(unsigned int, void __percpu *);
| ^~~~~~~~~~~~~~~
drivers/clocksource/timer-of.c: In function ‘timer_of_irq_init’:
drivers/clocksource/timer-of.c:74:51: error: passing argument 4 of
‘request_percpu_irq’ from pointer to non-enclosed address space
74 | np->full_name, clkevt) :
| ^~~~~~
./include/linux/interrupt.h:190:56: note: expected ‘__seg_gs void *’
but argument is of type ‘struct clock_event_device *’
190 | const char *devname, void __percpu *percpu_dev_id)
It appears the code is incorrect as reported by Uros Bizjak:
"The referred code is questionable as it tries to reuse
the clkevent pointer once as percpu pointer and once as generic
pointer, which should be avoided."
This change removes the percpu related code as no drivers is using it.
projects / thirdparty / kernel / stable.git / log
