The input gain range TLV was declared as -70dB to 0dB, but the preamp
gain range is actually 0dB to +70dB. Rename SCARLETT2_GAIN_BIAS to
SCARLETT2_MAX_GAIN and update the TLV to fix.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu> Fixes: 0a995e38dc44 ("ALSA: scarlett2: Add support for software-controllable input gain") Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <9168317b5ac5335943d3f14dbcd1cc2d9b2299d0.1710047969.git.g@b4.vu> Signed-off-by: Sasha Levin <sashal@kernel.org>
The meanings of the raw_auto_gain_status values were originally
guessed through experimentation, but the official names have now been
discovered. Update the autogain status control strings accordingly.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu> Fixes: 0a995e38dc44 ("ALSA: scarlett2: Add support for software-controllable input gain") Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <8bd12a5e7dc714801dd9887c4bc5cb35c384e27c.1710047969.git.g@b4.vu> Signed-off-by: Sasha Levin <sashal@kernel.org>
The value currently being read to determine the low-voltage state is
actually the front panel state. Fix the code to use the correct offset
for the low-voltage state.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu> Fixes: d7cfa2fdfc8a ("ALSA: scarlett2: Add power status control") Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <d97b7d87f43b0e54f37e1552394be2f3ae182704.1710047969.git.g@b4.vu> Signed-off-by: Sasha Levin <sashal@kernel.org>
The runtime_resume function calls prmg_load and apply_calibration
functions, but system_resume also calls them, so calling
pm_runtime_force_resume before reset is unnecessary.
For consistency, do not call the pm_runtime_force_suspend in
system_suspend, as runtime_suspend does the same.
Realtek codec on HP Envy laptop series are heavily modified by vendor.
Therefore, need intervention to make it work properly. The patch fixes:
- B&O soundbar speakers (between lid and keyboard) activation
- Enable LED on mute button
- Add missing process coefficient which affects the output amplifier
- Volume control synchronization between B&O soundbar and side speakers
- Unmute headset output on several HP Envy models
- Auto-enable headset mic when plugged
This patch was tested on HP Envy x360 13-AR0107AU with Realtek ALC285
The only unsolved problem is output amplifier of all built-in speakers
is too weak, which causes volume of built-in speakers cannot be loud
as vendor's proprietary driver due to missing _DSD parameter in the
firmware. The solution is currently on research. Expected to has another
patch in the future.
Potential fix to related issues, need test before close those issues:
cifs writeback doesn't correctly handle the case where
cifs_extend_writeback() hits a point where it is considering an additional
folio, but this would overrun the wsize - at which point it drops out of
the xarray scanning loop and calls xas_pause(). The problem is that
xas_pause() advances the loop counter - thereby skipping that page.
What needs to happen is for xas_reset() to be called any time we decide we
don't want to process the page we're looking at, but rather send the
request we are building and start a new one.
Fix this by copying and adapting the netfslib writepages code as a
temporary measure, with cifs writeback intending to be offloaded to
netfslib in the near future.
This also fixes the issue with the use of filemap_get_folios_tag() causing
retry of a bunch of pages which the extender already dealt with.
This can be tested by creating, say, a 64K file somewhere not on cifs
(otherwise copy-offload may get underfoot), mounting a cifs share with a
wsize of 64000, copying the file to it and then comparing the original file
and the copy:
Without the fix, the cmp fails at position 64000 (or shortly thereafter).
Fixes: d08089f649a0 ("cifs: Change the I/O paths to use an iterator rather than a page list") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: Tom Talpey <tom@talpey.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: samba-technical@lists.samba.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kmalloc() in zynq_clk_setup() will return null if the
physical memory has run out. As a result, if we use snprintf()
to write data to the null address, the null pointer dereference
bug will happen.
This patch uses a stack variable to replace the kmalloc().
Fixes: 0ee52b157b8e ("clk: zynq: Add clock controller driver") Suggested-by: Michal Simek <michal.simek@amd.com> Suggested-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/20240301084437.16084-1-duoming@zju.edu.cn Acked-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
__clk_get_hw() can return NULL which is dereferenced by clk_core_get() at
hw->core.
Prior to commit dde4eff47c82 ("clk: Look for parents with clkdev based
clk_lookups") the check IS_ERR_OR_NULL() was performed which would have
caught the NULL.
Reading the description of this function it talks about returning NULL but
that cannot be so at the moment.
Update the function to check for hw before dereferencing it and return NULL
if hw is NULL.
sparc32 do not support generic isa dma, so do not select the symbol.
This fixes the following warnings:
dma.c:70:5: error: no previous prototype for 'request_dma' [-Werror=missing-prototypes]
dma.c:88:6: error: no previous prototype for 'free_dma' [-Werror=missing-prototypes]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Fixes: 0fcb70851fbf ("Makefile.extrawarn: turn on missing-prototypes globally") Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Cc: Andreas Larsson <andreas@gaisler.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Reviewed-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Andreas Larsson <andreas@gaisler.com> Link: https://lore.kernel.org/r/20240224-sam-fix-sparc32-all-builds-v2-5-1f186603c5c4@ravnborg.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the generic variants - the implementation is the same.
As a nice side-effect fix the following warnings:
cmpdi2.c: warning: no previous prototype for '__cmpdi2' [-Wmissing-prototypes]
ucmpdi2.c: warning: no previous prototype for '__ucmpdi2' [-Wmissing-prototypes]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Fixes: 0fcb70851fbf ("Makefile.extrawarn: turn on missing-prototypes globally") Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk> Tested-by: Maciej W. Rozycki <macro@orcam.me.uk> # build-tested Cc: "David S. Miller" <davem@davemloft.net> Cc: Andreas Larsson <andreas@gaisler.com> Reviewed-by: Andreas Larsson <andreas@gaisler.com> Tested-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Andreas Larsson <andreas@gaisler.com> Link: https://lore.kernel.org/r/20240224-sam-fix-sparc32-all-builds-v2-1-1f186603c5c4@ravnborg.org Signed-off-by: Sasha Levin <sashal@kernel.org>
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
of_property_read_u32 returns 0 when success, so reverse the
return value to get the true value.
Fixes: f8449c8f7355 ("backlight: ktz8866: Add support for Kinetic KTZ8866 backlight") Signed-off-by: Jianhua Lu <lujianhua000@gmail.com> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Link: https://lore.kernel.org/r/20240129122829.16248-1-lujianhua000@gmail.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enabling strobe and then setting brightness to 0 causes the driver to enter
invalid state after strobe end timer fires. We should cancel strobe mode
resources when changing brightness (aka torch mode).
Fixes: cef8ec8cbd21 ("leds: add sgm3140 driver") Signed-off-by: Ondrej Jirman <megi@xff.cz> Link: https://lore.kernel.org/r/20240217191133.1757553-1-megi@xff.cz Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the probe() callback in case of error mutex is destroyed being locked
which is not allowed so unlock the mutex before destroying.
Fixes: 59ea3c9faf32 ("leds: add aw2013 driver") Signed-off-by: George Stark <gnstark@salutedevices.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20231214173614.2820929-2-gnstark@salutedevices.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the prototypes into mpc10x.h which is included by all the relevant
C files, fixes:
arch/powerpc/platforms/embedded6xx/ls_uart.c:59:6: error: no previous prototype for 'avr_uart_configure'
arch/powerpc/platforms/embedded6xx/ls_uart.c:82:6: error: no previous prototype for 'avr_uart_send'
The charge_behaviours property is meant as a control-knob that can be
changed by the user.
Page 23 of [0] which documents the flag CHG_INH as follows:
CHG_INH : Charge Inhibit When the current is more than or equal to charge
threshold current,
charge inhibit temperature (upper/lower limit) ：1
charge permission temperature or the current is
less than charge threshold current ：0
So this is pure read-only information which is better represented as
POWER_SUPPLY_STATUS_NOT_CHARGING.
Two regs have wrong values in existing fields, change them to match
the datasheet.
Fixes: ace6d1448138 ("mfd: cs42l43: Add support for cs42l43 core driver") Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20240301101547.2136948-1-mstrozek@opensource.cirrus.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The synchronization here is to ensure the ordering of freeing of a module
init so that it happens before W+X checking. It is worth noting it is not
that the freeing was not happening, it is just that our sanity checkers
raced against the permission checkers which assume init memory is already
gone.
Commit 1a7b7d922081 ("modules: Use vmalloc special flag") moved calling
do_free_init() into a global workqueue instead of relying on it being
called through call_rcu(..., do_free_init), which used to allowed us call
do_free_init() asynchronously after the end of a subsequent grace period.
The move to a global workqueue broke the gaurantees for code which needed
to be sure the do_free_init() would complete with rcu_barrier(). To fix
this callers which used to rely on rcu_barrier() must now instead use
flush_work(&init_free_wq).
Without this fix, we still could encounter false positive reports in W+X
checking since the rcu_barrier() here can not ensure the ordering now.
Even worse, the rcu_barrier() can introduce significant delay. Eric
Chanudet reported that the rcu_barrier introduces ~0.1s delay on a
PREEMPT_RT kernel.
[ 0.291444] Freeing unused kernel memory: 5568K
[ 0.402442] Run /sbin/init as init process
With this fix, the above delay can be eliminated.
Link: https://lkml.kernel.org/r/20240227023546.2490667-1-changbin.du@huawei.com Fixes: 1a7b7d922081 ("modules: Use vmalloc special flag") Signed-off-by: Changbin Du <changbin.du@huawei.com> Tested-by: Eric Chanudet <echanude@redhat.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Xiaoyi Su <suxiaoyi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The stack_pools[] array has DEPOT_MAX_POOLS. The "pools_num" tracks the
number of pools which are initialized. See depot_init_pool() for more
details.
If pool_index == pools_num_cached, this will read one element beyond what
we want. If not all the pools are initialized, then the pool will be
NULL, triggering a WARN(), and if they are all initialized it will read
one element beyond the end of the array.
Link: https://lkml.kernel.org/r/361ac881-60b7-471f-91e5-5bf8fe8042b2@moroto.mountain Fixes: b29d31885814 ("lib/stackdepot: store free stack records in a freelist") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "page_owner: print stacks and their outstanding allocations",
v10.
page_owner is a great debug functionality tool that lets us know about all
pages that have been allocated/freed and their specific stacktrace. This
comes very handy when debugging memory leaks, since with some scripting we
can see the outstanding allocations, which might point to a memory leak.
In my experience, that is one of the most useful cases, but it can get
really tedious to screen through all pages and try to reconstruct the
stack <-> allocated/freed relationship, becoming most of the time a
daunting and slow process when we have tons of allocation/free operations.
This patchset aims to ease that by adding a new functionality into
page_owner. This functionality creates a new directory called
'page_owner_stacks' under 'sys/kernel//debug' with a read-only file called
'show_stacks', which prints out all the stacks followed by their
outstanding number of allocations (being that the times the stacktrace has
allocated but not freed yet). This gives us a clear and a quick overview
of stacks <-> allocated/free.
We take advantage of the new refcount_f field that stack_record struct
gained, and increment/decrement the stack refcount on every
__set_page_owner() (alloc operation) and __reset_page_owner (free
operation) call.
Unfortunately, we cannot use the new stackdepot api STACK_DEPOT_FLAG_GET
because it does not fulfill page_owner needs, meaning we would have to
special case things, at which point makes more sense for page_owner to do
its own {dec,inc}rementing of the stacks. E.g: Using
STACK_DEPOT_FLAG_PUT, once the refcount reaches 0, such stack gets
evicted, so page_owner would lose information.
This patchset also creates a new file called 'set_threshold' within
'page_owner_stacks' directory, and by writing a value to it, the stacks
which refcount is below such value will be filtered out.
The very first entry of stack_record gets a handle of 0, but this is wrong
because stackdepot treats a 0-handle as a non-valid one. E.g: See the
check in stack_depot_fetch()
Fix this by adding and offset of 1.
This bug has been lurking since the very beginning of stackdepot, but no
one really cared as it seems. Because of that I am not adding a Fixes
tag.
Link: https://lkml.kernel.org/r/20240215215907.20121-1-osalvador@suse.de Link: https://lkml.kernel.org/r/20240215215907.20121-2-osalvador@suse.de Co-developed-by: Marco Elver <elver@google.com> Signed-off-by: Marco Elver <elver@google.com> Signed-off-by: Oscar Salvador <osalvador@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Andrey Konovalov <andreyknvl@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: dc24559472a6 ("lib/stackdepot: off by one in depot_fetch_stack()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 'grouped target' is used only in 'make' 4.3, it should
be avoided. Replace it with 'multi-target pattern rule' which
has the same behavior.
Fixes: 9616e74b796c ("drm/xe: Add support for OOB workarounds") Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240302153927.2602241-1-dhirschfeld@habana.ai
[ reword commit message ] Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 5224ed586ba7f9bba956655a1bfe5b75df7394d4) Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove locks calls in usbtv_video_free() because
are useless and may led to a deadlock as reported here:
https://syzkaller.appspot.com/x/bisect.txt?x=166dc872180000
Also remove usbtv_stop() call since it will be called when
unregistering the device.
Before 'c838530d230b' this issue would only be noticed if you
disconnect while streaming and now it is noticeable even when
disconnecting while not streaming.
Fixes: c838530d230b ("media: media videobuf2: Be more flexible on the number of queue stored buffers") Fixes: f3d27f34fdd7 ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber") Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Tomasz Figa <tfiga@chromium.org> Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix minor spelling mistake in log message] Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting up the timing engine when the physical encoder has a split role
neglects dividing the drm_display_mode's hskew parameter. Let's fix this
since this must also be done in preparation for implementing YUV420 over
DP.
CDM block supports formats other than H1V2 for DP. Since we are now
adding support for CDM over DP, relax the checks to allow all other
formats for DP other than H1V2.
Changes in v2:
- Add fixes tag
- Move patch to top of series
L3PMCx0AC and L3PMCx0AD, used in l3_xi_sampled_latency* events, have a
quirk that requires them to be programmed with SliceId set to 0x3.
Without this, the events do not count at all and affects dependent
metrics such as l3_read_miss_latency.
If ThreadMask is not specified, the amd-uncore driver internally sets
ThreadMask to 0x3, EnAllCores to 0x1 and EnAllSlices to 0x1 but does
not set SliceId. Since SliceId must also be set to 0x3 in this case,
specify all the other fields explicitly.
E.g.
$ sudo perf stat -e l3_xi_sampled_latency.all,l3_xi_sampled_latency_requests.all -a sleep 1
The current register offset used for the GCC_UBI0_AXI_ARES reset
seems wrong. Or at least, the downstream driver uses [1] the same
offset which is used for other the GCC_UBI0_*_ARES resets.
Change the code to use the same offset used in the downstream
driver and also specify the reset bit explicitly to use the
same format as the followup entries.
Based on the table, it is quite likely that the pcie0 and the pci1
clocks are using the same register layout, however it seems that
the value of the 'halt_reg' field in the 'gcc_pcie1_pipe_clk' clock
is wrong.
In the downstream driver [1], the same '0x76018' value is used for
both the 'halt_reg' and for the 'enable_reg' fields of the
'gcc_pcie1_pipe_clk' clock.
Update the current driver to use the same value used downstream as
probably that is the correct value.
The value of the 'enable_reg' field in the 'gcc_gmac0_sys_clk'
clock definition seems wrong as it is greater than the
'max_register' value defined in the regmap configuration.
Additionally, all other gmac specific branch clock definitions
within the driver uses the same value both for the 'enable_reg'
and for the 'halt_reg' fields.
Due to the lack of documentation the correct value is not known.
Looking into the downstream driver does not help either, as that
uses the same (presumably wrong) value [1].
Nevertheless, change the 'enable_reg' field of 'gcc_gmac0_sys_clk'
to use the value from the 'halt_reg' field so it follows the pattern
used in other gmac clock definitions. The change is based on the
assumption that the register layout of this clock is the same
as the other gmac clocks.
Running event hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
in one of the system throws below error:
---Logs---
# perf list | grep hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=?/[Kernel PMU event]
# perf stat -v -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event is not supported by the kernel.
failed to read counter hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
The above error is because of the hcall failure as required
permission "Enable Performance Information Collection" is not set.
Based on current code, single_gpci_request function did not check the
error type incase hcall fails and by default returns EINVAL. But we can
have other reasons for hcall failures like H_AUTHORITY/H_PARAMETER with
detail_rc as GEN_BUF_TOO_SMALL, for which we need to act accordingly.
Fix this issue by adding new checks in the single_gpci_request and
h_gpci_event_init functions.
Result after fix patch changes:
# perf stat -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Error:
No permission to enable hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event.
Fixes: 220a0c609ad1 ("powerpc/perf: Add support for the hv gpci (get performance counter info) interface") Reported-by: Akanksha J N <akanksha@linux.ibm.com> Signed-off-by: Kajol Jain <kjain@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240229122847.101162-1-kjain@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible that mtk_crtc->event is NULL in
mtk_drm_crtc_finish_page_flip().
pending_needs_vblank value is set by mtk_crtc->event, but in
mtk_drm_crtc_atomic_flush(), it's is not guarded by the same
lock in mtk_drm_finish_page_flip(), thus a race condition happens.
Consider the following case:
CPU1 CPU2
step 1:
mtk_drm_crtc_atomic_begin()
mtk_crtc->event is not null,
step 1:
mtk_drm_crtc_atomic_flush:
mtk_drm_crtc_update_config(
!!mtk_crtc->event)
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip:
lock
mtk_crtc->event set to null,
pending_needs_vblank set to false
unlock
pending_needs_vblank set to true,
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip called again,
pending_needs_vblank is still true
//null pointer
Instead of guarding the entire mtk_drm_crtc_atomic_flush(), it's more
efficient to just check if mtk_crtc->event is null before use.
Where:
- slpm is a unsigned int pointer;
- g->grp.pins[i] is a pin number. It can grow to more than 32.
The expected shift amount is a pin bank offset.
This bug does not occur on every group or pin: the altsetting must be
NMK_GPIO_ALT_C and the pin must be 32 or above. It might have occured.
For example, in pinctrl-nomadik-db8500.c, pin group i2c3_c_2 has the
right altsetting and pins 229 and 230.
Per commit b3f11af9b2ce ("arm64: ftrace: forbid CALL_OPS with
CC_OPTIMIZE_FOR_SIZE"), GCC is silently ignoring `-falign-functions=N`
when passed `-Os`, causing functions to be improperly aligned. This
doesn't seem to be a problem with Clang though, where enabling CALL_OPS
with CC_OPTIMIZE_FOR_SIZE doesn't spit out any warnings at boot about
misaligned patch-sites. Only forbid CALL_OPS if GCC is used and we're
optimizing for size so that CALL_OPS can be used with clang optimizing
for size.
Cc: Jason Ling <jasonling@chromium.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Bill Wendling <morbo@google.com> Cc: Justin Stitt <justinstitt@google.com> Cc: llvm@lists.linux.dev Fixes: b3f11af9b2ce ("arm64: ftrace: forbid CALL_OPS with CC_OPTIMIZE_FOR_SIZE") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/r/20240223064032.3463229-1-swboyd@chromium.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When saa7146_register_device and saa7146_vv_init fails, budget_av_attach
should free the resources it allocates, like the error-handling of
ttpci_budget_init does. Besides, there are two fixme comment refers to
such deallocations.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
A previous patch worked around a KASAN issue in stv0367, now a similar
problem showed up with clang:
drivers/media/dvb-frontends/stv0367.c:1222:12: error: stack frame size (3624) exceeds limit (2048) in 'stv0367ter_set_frontend' [-Werror,-Wframe-larger-than]
1214 | static int stv0367ter_set_frontend(struct dvb_frontend *fe)
Rework the stv0367_writereg() function to be simpler and mark both
register access functions as noinline_for_stack so the temporary
i2c_msg structures do not get duplicated on the stack when KASAN_STACK
is enabled.
[Syzbot reported]
BUG: KASAN: slab-use-after-free in pvr2_context_set_notify+0x2c4/0x310 drivers/media/usb/pvrusb2/pvrusb2-context.c:35
Read of size 4 at addr ffff888113aeb0d8 by task kworker/1:1/26
[Analyze]
Task A set disconnect_flag = !0, which resulted in Task B's condition being met
and releasing mp, leading to this issue.
[Fix]
Place the disconnect_flag assignment operation after all code in pvr2_context_disconnect()
to avoid this issue.
Reported-and-tested-by: syzbot+ce750e124675d4599449@syzkaller.appspotmail.com Fixes: e5be15c63804 ("V4L/DVB (7711): pvrusb2: Fix race on module unload") Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Missing break statement in the ATOM_ARG_IMM case of a switch statement,
adds the missing break statement, ensuring that the program's control
flow is as intended.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/atom.c:323 atom_get_src_int() warn: ignoring unreachable code.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)") Cc: Jammy Zhou <Jammy.Zhou@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
HP ProBook x360 435 G7 using older version of firmware which doesn't
support disabling the interrupt for all commands. Hence avoid disabling
the interrupt for that particular model.
HPD sensor data is not populating properly because of wrong order of HPD
sensor structure elements. So update the order of structure elements to
match the HPD sensor data received from the firmware.
The if condition for the SM8[45]50 GPU SMMU is too large,
add the other compatible strings to the condition to only
allow the clocks for the GPU SMMU nodes.
Fixes: 4fff78dc2490 ("dt-bindings: arm-smmu: Document SM8[45]50 GPU SMMU") Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/578686/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Historically the Adreno driver has not been updating memory
configuration registers on a618 (SC7180 platform) implying that the
default configuration is fine. After the rework performed in the commit 8814455a0e54 ("drm/msm: Refactor UBWC config setting") the function
a6xx_calc_ubwc_config() still contained this shortcut and did not
calculate UBWC configuration. However the function which now actually
updates hardware registers, a6xx_set_ubwc_config(), doesn't contain such
check.
Rather than adding the check to a6xx_set_ubwc_config(), fill in the
UBWC config for a618 (based on readings from SC7180).
According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
mtd-ram can potentially be larger than 4GB. get_bitmask_order() uses
fls() that is not guaranteed to work with values larger than 32-bit.
Specifically on aarch64 fls() returns 0 when all 32 LSB bits are clear.
Use fls64() instead.
There is SAI1, SAI2, SAI3, SAI5, SAI6, SAI7 existing in this block
control, the order is discontinuous. The definition of SAI_MCLK_SEL(n)
is not match with the usage of CLK_SAIn(n).
So define SAI##n##_MCLK_SEL separately to fix the issue.
Fixes: 6cd95f7b151c ("clk: imx: imx8mp: Add audiomix block control") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/1708683351-8504-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A sync lost issue can be observed with two displays, when moving a plane
from one disabled display to an another disabled display, and then
enabling the display to which the plane was moved to. The exact
requirements for this to trigger are not clear.
It looks like the issue is that the layers are left enabled in the first
display's OVR registers. Even if the corresponding VP is disabled, it
still causes an issue, as if the disabled VP and its OVR would still be
in use, leading to the same VID being used by two OVRs. However, this is
just speculation based on testing the DSS behavior.
Experimentation shows that as a workaround, we can disable all the
layers in the OVR when disabling a VP. There should be no downside to
this, as the OVR is anyway effectively disabled if its VP is disabled,
and it seems to solve the sync lost issue.
However, there may be a bigger issue in play here, related to J721e
erratum i2097 ("DSS: Disabling a Layer Connected to Overlay May Result
in Synclost During the Next Frame"). Experimentation also shows that the
OVR's CHANNELIN field has similar issue. So we may need to revisit this
when we find out more about the core issue.
When the driver sets up the zpos property it sets the default zpos value
to the HW id of the plane. That is fine as such, but as on many DSS
versions the driver arranges the DRM planes in a different order than
the HW planes (to keep the non-scalable planes first), this leads to odd
initial zpos values. An example is J721e, where the initial zpos values
for DRM planes are 1, 3, 0, 2.
In theory the userspace should configure the zpos values properly when
using multiple planes, and in that sense the initial zpos values
shouldn't matter, but there's really no reason not to fix this and help
the userspace apps which don't handle zpos perfectly. In particular,
some versions of Weston seem to have issues dealing with the planes
with the current default zpos values.
So let's change the zpos values for the DRM planes to 0, 1, 2, 3.
Another option would be to configure the planes marked as primary planes
to zpos 0. On a two display system this would give us plane zpos values
of 0, 0, 1, 2. The end result and behavior would be very similar in this
option, and I'm not aware that this would actually help us in any way.
So, to keep the code simple, I opted for the 0, 1, 2, 3 values.
If a device is configured for data compression chaining (dcc), half of the
engines are loaded with the symmetric crypto image and the rest are loaded
with the compression image.
However, in such configuration all rings can handle compression requests.
Fix the ring to service mapping so that when a device is configured for
dcc, the ring to service mapping reports that all rings in a bank can
be used for compression.
Fixes: fcf60f4bcf54 ("crypto: qat - add support for 420xx devices") Signed-off-by: Damian Muszynski <damian.muszynski@intel.com> Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a device is configured for data compression chaining (dcc), half of the
engines are loaded with the symmetric crypto image and the rest are loaded
with the compression image.
However, in such configuration all rings can handle compression requests.
Fix the ring to service mapping so that when a device is configured for
dcc, the ring to service mapping reports that all rings in a bank can
be used for compression.
Fixes: a238487f7965 ("crypto: qat - fix ring to service map for QAT GEN4") Signed-off-by: Damian Muszynski <damian.muszynski@intel.com> Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is to fix the following warning when compiling the QAT driver
using clang scan-build:
drivers/crypto/intel/qat/qat_common/adf_gen4_ras.c:1010:6: warning: Value stored to 'reg' during its initialization is never read [deadcode.DeadStores]
1010 | u32 reg = ADF_CSR_RD(csr, ADF_GEN4_SSMCPPERR);
| ^~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/crypto/intel/qat/qat_common/adf_gen4_ras.c:1109:6: warning: Value stored to 'reg' during its initialization is never read [deadcode.DeadStores]
1109 | u32 reg = ADF_CSR_RD(csr, ADF_GEN4_SER_ERR_SSMSH);
| ^~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 99b1c9826e48 ("crypto: qat - count QAT GEN4 errors") Signed-off-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check if delta_us is not zero and return -EINVAL if it is.
delta_us is unlikely to be zero as there is a sleep between the reads of
the two timestamps.
This is to fix the following warning when compiling the QAT driver
using clang scan-build:
drivers/crypto/intel/qat/qat_common/adf_clock.c:87:9: warning: Division by zero [core.DivideZero]
87 | temp = DIV_ROUND_CLOSEST_ULL(temp, delta_us);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: e2980ba57e79 ("crypto: qat - add measure clock frequency") Signed-off-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is to fix the following warning when compiling the QAT driver
using the clang compiler with CC=clang W=2:
drivers/crypto/intel/qat/qat_common/adf_cnv_dbgfs.c:19:9: warning: macro is not used [-Wunused-macros]
19 | #define CNV_SLICE_ERR_MASK GENMASK(7, 0)
| ^
Fixes: d807f0240c71 ("crypto: qat - add cnv_errors debugfs file") Signed-off-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
As a result of the removal of qat_zlib_deflate, some defines where not
removed. Remove them.
This is to fix the following warning when compiling the QAT driver
using the clang compiler with CC=clang W=2:
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:21:9: warning: macro is not used [-Wunused-macros]
21 | #define QAT_RFC_1950_CM_OFFSET 4
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:16:9: warning: macro is not used [-Wunused-macros]
16 | #define QAT_RFC_1950_HDR_SIZE 2
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:17:9: warning: macro is not used [-Wunused-macros]
17 | #define QAT_RFC_1950_FOOTER_SIZE 4
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:22:9: warning: macro is not used [-Wunused-macros]
22 | #define QAT_RFC_1950_DICT_MASK 0x20
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:18:9: warning: macro is not used [-Wunused-macros]
18 | #define QAT_RFC_1950_CM_DEFLATE 8
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:20:9: warning: macro is not used [-Wunused-macros]
20 | #define QAT_RFC_1950_CM_MASK 0x0f
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:23:9: warning: macro is not used [-Wunused-macros]
23 | #define QAT_RFC_1950_COMP_HDR 0x785e
| ^
drivers/crypto/intel/qat/qat_common/qat_comp_algs.c:19:9: warning: macro is not used [-Wunused-macros]
19 | #define QAT_RFC_1950_CM_DEFLATE_CINFO_32K 7
| ^
Fixes: e9dd20e0e5f6 ("crypto: qat - Remove zlib-deflate") Signed-off-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Errors can potentially occur in the "processing" of PSP commands or
commands can be processed successfully but still return an error code in
the header.
This second case was being discarded because PSP communication worked but
the command returned an error code in the payload header.
Capture both cases and return them to the caller as -EIO for the caller
to investigate. The caller can detect the latter by looking at
`req->header->status`.
Reported-and-tested-by: Tim Van Patten <timvp@google.com> Fixes: 7ccc4f4e2e50 ("crypto: ccp - Add support for an interface for platform features") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca3726 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON") Fixes: b59e2ae3690c ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the perf tool doesn't detect support for extended event types
on Apple M1/M2 systems, and will not auto-expand plain PERF_EVENT_TYPE
hardware events into per-PMU events. This is due to the detection of
extended event types not handling mandatory filters required by the
M1/M2 PMU driver.
PMU drivers and the core perf_events code can require that
perf_event_attr::exclude_* filters are configured in a specific way and
may reject certain configurations of filters, for example:
(a) Many PMUs lack support for any event filtering, and require all
perf_event_attr::exclude_* bits to be clear. This includes Alpha's
CPU PMU, and ARM CPU PMUs prior to the introduction of PMUv2 in
ARMv7,
(b) When /proc/sys/kernel/perf_event_paranoid >= 2, the perf core
requires that perf_event_attr::exclude_kernel is set.
(c) The Apple M1/M2 PMU requires that perf_event_attr::exclude_guest is
set as the hardware PMU does not count while a guest is running (but
might be extended in future to do so).
In is_event_supported(), we try to account for cases (a) and (b), first
attempting to open an event without any filters, and if this fails,
retrying with perf_event_attr::exclude_kernel set. We do not account for
case (c), or any other filters that drivers could theoretically require
to be set.
Thus is_event_supported() will fail to detect support for any events
targeting an Apple M1/M2 PMU, even where events would be supported with
perf_event_attr:::exclude_guest set.
Since commit:
82fe2e45cdb00de4 ("perf pmus: Check if we can encode the PMU number in perf_event_attr.type")
... we use is_event_supported() to detect support for extended types,
with the PMU ID encoded into the perf_event_attr::type. As above, on an
Apple M1/M2 system this will always fail to detect that the event is
supported, and consequently we fail to detect support for extended types
even when these are supported, as they have been since commit:
Due to this, the perf tool will not automatically expand plain
PERF_TYPE_HARDWARE events into per-PMU events, even when all the
necessary kernel support is present.
This patch updates is_event_supported() to additionally try opening
events with perf_event_attr::exclude_guest set, allowing support for
events to be detected on Apple M1/M2 systems. I believe that this is
sufficient for all contemporary CPU PMU drivers, though in future it may
be necessary to check for other combinations of filter bits.
I've deliberately changed the check to not expect a specific error code
for missing filters, as today ;the kernel may return a number of
different error codes for missing filters (e.g. -EACCESS, -EINVAL, or
-EOPNOTSUPP) depending on why and where the filter configuration is
rejected, and retrying for any error is more robust.
Note that this does not remove the need for commit:
a24d9d9dc096fc0d ("perf parse-events: Make legacy events lower priority than sysfs/JSON")
... which is still necessary so that named-pmu/event/ events work on
kernels without extended type support, even if the event name happens to
be the same as a PERF_EVENT_TYPE_HARDWARE event (e.g. as is the case for
the M1/M2 PMU's 'cycles' and 'instructions' events).
Fixes: 82fe2e45cdb00de4 ("perf pmus: Check if we can encode the PMU number in perf_event_attr.type") Signed-off-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Ian Rogers <irogers@google.com> Tested-by: James Clark <james.clark@arm.com> Tested-by: Marc Zyngier <maz@kernel.org> Cc: Hector Martin <marcan@marcan.st> Cc: James Clark <james.clark@arm.com> Cc: John Garry <john.g.garry@oracle.com> Cc: Leo Yan <leo.yan@linux.dev> Cc: Mike Leach <mike.leach@linaro.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240126145605.1005472-1-mark.rutland@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: f36e789a1f8d ("mfd: altera-sysmgr: Add SOCFPGA System Manager") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-4-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: 45330bb43421 ("mfd: syscon: Allow property as NULL in syscon_regmap_lookup_by_phandle") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-2-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch swaps SINK and SOURCE pads of the MEI CSI sub-device. While
this does change the UAPI by swapping the pads, the driver has never been
usable in upstream kernel as the Intel IPU6 driver it depends on any
functionality has not yet been merged.
mips_ejtag_fdc_encode() method expects having a first argument passed of
the "u8 **" type, meanwhile the driver passes the "const char **" type.
That causes the next build-warning:
drivers/tty/mips_ejtag_fdc.c: In function ‘mips_ejtag_fdc_console_write’:
drivers/tty/mips_ejtag_fdc.c:343:32: error: passing argument 1 of ‘mips_ejtag_fdc_encode’ from incompatible pointer type [-Werror=incompatible-pointer-types]
word = mips_ejtag_fdc_encode(&buf_ptr, &buf_len, 1);
^
drivers/tty/mips_ejtag_fdc.c:216:24: note: expected ‘const u8 ** {aka const unsigned char **}’ but argument is of type ‘const char **’
static struct fdc_word mips_ejtag_fdc_encode(const u8 **ptrs,
^~~~~~~~~~~~~~~~~~~~~
Fix it by altering the type of the pointer which is passed to the
mips_ejtag_fdc_encode() method.
Fixes: ce7cbd9a6c81 ("tty: mips_ejtag_fdc: use u8 for character pointers") Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside tegra_fb_create(), drm_gem_object_lookup() increments ref count of
the found object. But if the following size check fails then the last
found object's ref count should be put there as the unreferencing loop
can't detect this situation.
Found by Linux Verification Center (linuxtesting.org).
Without the SGM_REG_SEL clock enabled the cpu freezes if trying to
access registers used by MT7981 clock drivers itself.
Mark SGM_REG_SEL as critical to make sure it is always enabled to
prevent freezes on boot even if the Ethernet driver which prepares
and enables the clock is not loaded or probed at a later point.
CLK_INFRA_SSPM_32K_SELF has the "f_f26m_ck" clock assigned as its parent.
This is inconsistent as the clock is part of a group that are all gates
without dividers, and this makes the kernel think it runs at 26 MHz.
After clarification from MediaTek engineers, the correct parent is
actually the system 32 KHz clock.
Fixes: 1eb8d61ac5c9 ("clk: mediatek: mt8183: Add back SSPM related clocks") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Link: https://lore.kernel.org/r/20240219105125.956278-1-wenst@chromium.org Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
The panel on sc7180-trogdor-wormdingler and
sc7180-trogdor-quackingstick hasn't been coming up since commit 9e15123eca79 ("drm/msm/dsi: Stop unconditionally powering up DSI hosts
at modeset"). Let's add "prepare_prev_first" as has been done for many
other DSI panels.
projects / thirdparty / kernel / stable.git / log
