After writing the page tables, we use __inval_cache_range to invalidate
any stale cache entries. Strongly Ordered memory accesses are not
ordered w.r.t. cache maintenance instructions, and hence explicit memory
barriers are required to provide this ordering. However,
__inval_cache_range was written to be used on Normal Cacheable memory
once the MMU and caches are on, and does not have any barriers prior to
the DC instructions.
This patch adds a DMB between the page tables being written and the
corresponding cachelines being invalidated, ensuring that the
invalidation makes the new data visible to subsequent cacheable
accesses. A barrier is not required before the prior invalidate as we do
not access the page table memory area prior to this, and earlier
barriers in preserve_boot_args and set_cpu_boot_mode_flag ensures
ordering w.r.t. any stores performed prior to entering Linux.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: c218bca74eeafa2f ("arm64: Relax the kernel cache requirements for boot") Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.
In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.
Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: Archit Taneja <architt@codeaurora.org> Fixes: bcd61c0f535a (clk: qcom: Add support for root clock
generators (RCGs)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
... but in case in future we might use facilities such as LTO, then
OPTIMIZER_HIDE_VAR() is not sufficient to protect gcc from a possible
eviction of the memset(). We have to use a compiler barrier instead.
Minimal test example when we assume memzero_explicit() would *not* be
a call, but would have been *inlined* instead:
As GMUX depends on IO for iGP to be enabled and active, lock the IO at
vgaarb level. This should prevent GPU driver for dGPU to disable IO for
iGP while it tries to own legacy VGA IO.
This fixes usage of backlight control combined with closed nvidia
driver on some Apple dual-GPU (intel/nvidia) systems.
On those systems loading nvidia driver disables intel IO decoding,
disabling the gmux backlight controls as a side effect.
Prior to commits moving boot_vga from (optional) efifb to less optional
vgaarb this mis-behavior could be avoided by using right kernel config
(efifb enabled but vgaarb disabled).
This patch explicitly does not try to trigger vgaarb changes in order
to avoid confusing already running graphics drivers. If IO has been
mis-configured by vgaarb gmux will thus fail to probe.
It is expected to load/probe gmux prior to graphics drivers.
Fixes: ce027dac592c0ada241ce0f95ae65856828ac450 # nvidia interaction
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=86121 Reported-by: Petri Hodju <petrihodju@yahoo.com> Tested-by: Petri Hodju <petrihodju@yahoo.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Matthew Garrett <matthew.garrett@nebula.com> Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Set the SYSCIER as per the values indicated in the documentation.
The value previously used appears to been copied from the r8a7779
implementation but on closer inspection is not correct for the r8a7790.
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.
This bug has been found by adding a __printf attribute to
wl1271_format_buffer. gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".
Fixes: c5d94169e818 ("wl18xx: use new fw stats structures") Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
Tested-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Grant Likely <grant.likely@linaro.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Calling unlazy_walk() in walk_component() and do_last() when we find
a symlink that needs to be followed doesn't acquire a reference to vfsmount.
That's fine when the symlink is on the same vfsmount as the parent directory
(which is almost always the case), but it's not always true - one _can_
manage to bind a symlink on top of something. And in such cases we end up
with excessive mntput().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
acpi_scan_is_offline() may be called under the physical_node_lock
lock of the given device object's parent, so prevent lockdep from
complaining about that by annotating that instance with
SINGLE_DEPTH_NESTING.
Fixes: caa73ea158de (ACPI / hotplug / driver core: Handle containers in a special way) Reported-and-tested-by: Xie XiuQi <xiexiuqi@huawei.com> Reviewed-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
I noticed this only by reading the code. To my knowledge it shouldn't
cause any real problems at the moment, since the power well backing this
register remains on across a runtime s/r. This may change once
system-wide s0ix functionality is enabled in the kernel.
v2:
- resend after a missing git add -u :/
Signed-off-by: Imre Deak <imre.deak@intel.com> Tested-By: PRC QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The hardware, according to the specs, is limited to 256 byte transfers,
and current driver has no protections in case users attempt to do larger
transfers. The code will just stomp over status register and mayhem
ensues.
Let's split larger transfers into digestable chunks. Doing this allows
Atmel MXT driver on Pixel 1 function properly (it hasn't since commit 9d8dc3e529a19e427fd379118acd132520935c5d "Input: atmel_mxt_ts -
implement T44 message handling" which tries to consume multiple
touchscreen/touchpad reports in a single transaction).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Chuck pointed out a problem that crept in with commit 6ffa30d3f734 (nfs:
don't call blocking operations while !TASK_RUNNING). Linux counts tasks
in uninterruptible sleep against the load average, so this caused the
system's load average to be pinned at at least 1 when there was a
NFSv4.1+ mount active.
Not a huge problem, but it's probably worth fixing before we get too
many complaints about it. This patch converts the code back to use
TASK_INTERRUPTIBLE sleep, simply has it flush any signals on each loop
iteration. In practice no one should really be signalling this thread at
all, so I think this is reasonably safe.
With this change, there's also no need to game the hung task watchdog so
we can also convert the schedule_timeout call back to a normal schedule.
Reported-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Tested-by: Chuck Lever <chuck.lever@oracle.com> Fixes: commit 6ffa30d3f734 (“nfs: don't call blocking . . .”) Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 523c5b89640e ("i2c: Remove support for legacy PM") removed the PM
ops from the bus type, which causes the pm operations on the s3c2410
adapter device to fail (-ENOSUPP in rpm_callback). The adapter device
doesn't get bound to a driver and as such can't have its own pm_runtime
callbacks. Previously this was fine as the bus callbacks would have been
used, but now this can cause devices which use PM runtime and are
attached over I2C to fail to resume.
This commit fixes this issue by marking all adapter devices with
pm_runtime_no_callbacks, since they can't have any.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Beata Michalska <b.michalska@samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Fixes: 523c5b89640e Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
master_xfer() method should return number of i2c messages transferred,
but on Rockchip we were usually returning just 1, which caused trouble
with users that actually check number of transferred messages vs.
checking for negative error codes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fixed this behaviour by calling register_pernet_subsys(&nfsd_net_ops) before
registering rpc_pipefs_event(...) with the notifier chain.
Signed-off-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Signed-off-by: Lorenzo Restelli <lorenzo.restelli.ext@nokia.com> Reviewed-by: Kinlong Mee <kinglongmee@gmail.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
mvsas is giving a General protection fault when it encounters an expander
attached ATA device. Analysis of mvs_task_prep_ata() shows that the driver is
assuming all ATA devices are locally attached and obtaining the phy mask by
indexing the local phy table (in the HBA structure) with the phy id. Since
expanders have many more phys than the HBA, this is causing the index into the
HBA phy table to overflow and returning rubbish as the pointer.
mvs_task_prep_ssp() instead does the phy mask using the port properties.
Mirror this in mvs_task_prep_ata() to fix the panic.
Reported-by: Adam Talbot <ajtalbot1@gmail.com> Tested-by: Adam Talbot <ajtalbot1@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
ptrace_resume() is called when the tracee is still __TASK_TRACED. We set
tracee->exit_code and then wake_up_state() changes tracee->state. If the
tracer's sub-thread does wait() in between, task_stopped_code(ptrace => T)
wrongly looks like another report from tracee.
This confuses debugger, and since wait_task_stopped() clears ->exit_code
the tracee can miss a signal.
Note for stable: the bug is very old, but without 9899d11f6544 "ptrace:
ensure arch_ptrace/ptrace_request can never race with SIGKILL" the fix
should use lock_task_sighand(child).
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Pavel Labath <labath@google.com> Tested-by: Pavel Labath <labath@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When UNMAP command is issued with DIF protection support enabled,
the protection info for the unmapped region is remain unchanged.
So READ command for the region causes data integrity failure.
This fixes it by invalidating protection info for the unmapped region
by filling with 0xff pattern. This change also adds helper function
fd_do_prot_fill() in order to reduce code duplication with existing
fd_format_prot().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In fd_do_prot_rw(), it allocates prot_buf which is used to copy from
se_cmd->t_prot_sg by sbc_dif_copy_prot(). The SG table for prot_buf
is also initialized by allocating 'se_cmd->t_prot_nents' entries of
scatterlist and setting the data length of each entry to PAGE_SIZE
at most.
However if se_cmd->t_prot_sg contains a clustered entry (i.e.
sg->length > PAGE_SIZE), the SG table for prot_buf can't be
initialized correctly and sbc_dif_copy_prot() can't copy to prot_buf.
(This actually happened with TCM loopback fabric module)
As prot_buf is allocated by kzalloc() and it's physically contiguous,
we only need a single scatterlist entry.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When CONFIG_DEBUG_SG=y and DIF protection support enabled, kernel
BUG()s are triggered due to the following two issues:
1) prot_sg is not initialized by sg_init_table().
When CONFIG_DEBUG_SG=y, scatterlist helpers check sg entry has a
correct magic value.
2) vmalloc'ed buffer is passed to sg_set_buf().
sg_set_buf() uses virt_to_page() to convert virtual address to struct
page, but it doesn't work with vmalloc address. vmalloc_to_page()
should be used instead. As prot_buf isn't usually too large, so
fix it by allocating prot_buf by kmalloc instead of vmalloc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In a call to ib_umem_get(), if address is 0x0 and size is
already page aligned, check added in commit 8494057ab5e4
("IB/uverbs: Prevent integer overflow in ib_umem_get address
arithmetic") will refuse to register a memory region that
could otherwise be valid (provided vm.mmap_min_addr sysctl
and mmap_low_allowed SELinux knobs allow userspace to map
something at address 0x0).
This patch allows back such registration: ib_umem_get()
should probably don't care of the base address provided it
can be pinned with get_user_pages().
There's two possible overflows, in (addr + size) and in
PAGE_ALIGN(addr + size), this patch keep ensuring none
of them happen while allowing to pin memory at address
0x0. Anyway, the case of size equal 0 is no more (partially)
handled as 0-length memory region are disallowed by an
earlier check.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com Cc: Shachar Raindel <raindel@mellanox.com> Cc: Jack Morgenstein <jackm@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If ib_umem_get() is called with a size equal to 0 and an
non-page aligned address, one page will be pinned and a
0-sized umem will be returned to the caller.
This should not be allowed: it's not expected for a memory
region to have a size equal to 0.
This patch adds a check to explicitly refuse to register
a 0-sized region.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com Cc: Shachar Raindel <raindel@mellanox.com> Cc: Jack Morgenstein <jackm@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
With CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE enabled, and a normal top-down
address allocation strategy, load_elf_binary() will attempt to map a PIE
binary into an address range immediately below mm->mmap_base.
Unfortunately, load_elf_ binary() does not take account of the need to
allocate sufficient space for the entire binary which means that, while
the first PT_LOAD segment is mapped below mm->mmap_base, the subsequent
PT_LOAD segment(s) end up being mapped above mm->mmap_base into the are
that is supposed to be the "gap" between the stack and the binary.
Since the size of the "gap" on x86_64 is only guaranteed to be 128MB this
means that binaries with large data segments > 128MB can end up mapping
part of their data segment over their stack resulting in corruption of the
stack (and the data segment once the binary starts to run).
Any PIE binary with a data segment > 128MB is vulnerable to this although
address randomization means that the actual gap between the stack and the
end of the binary is normally greater than 128MB. The larger the data
segment of the binary the higher the probability of failure.
Fix this by calculating the total size of the binary in the same way as
load_elf_interp().
Signed-off-by: Michael Davidson <md@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 61f77eda9bbf ("mm/hugetlb: reduce arch dependent code around
follow_huge_*") broke follow_huge_pmd() on s390, where pmd and pte
layout differ and using pte_page() on a huge pmd will return wrong
results. Using pmd_page() instead fixes this.
All architectures that were touched by that commit have pmd_page()
defined, so this should not break anything on other architectures.
Fixes: 61f77eda "mm/hugetlb: reduce arch dependent code around follow_huge_*" Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Hugh Dickins <hughd@google.com> Cc: Michal Hocko <mhocko@suse.cz>, Andrea Arcangeli <aarcange@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.
It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.
Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.
This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: Christoph Hellwig <hch@lst.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
kvm_init_msr_list is currently called before hardware_setup. As a result,
vmx_mpx_supported always returns false when kvm_init_msr_list checks whether to
save MSR_IA32_BNDCFGS.
Move kvm_init_msr_list after vmx_hardware_setup is called to fix this issue.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428864435-4732-1-git-send-email-namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
drm/i915: Stop gathering error states for CS error interrupts
but just clearing is apparently not enough: A sufficiently dead gpu
left behind by firmware (*cough* coreboot *cough*) can keep the gpu in
an endless loop of such interrupts, eventually leading to the nmi
firing. And definitely to what looks like a machine hang.
Since we don't even enable these interrupts on gen5+ let's do the same
on earlier platforms.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93171 Tested-by: Mono <mono-for-kernel-org@donderklumpen.de> Tested-by: info@gluglug.org.uk Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
ACPI_MTX_TABLES is acquired and released by the callers of
acpi_tb_install_standard_table() so releasing it in the function itself is
causing the following error in Linux kernel if the table is reloaded:
ACPI Error: Mutex [0x2] is not acquired, cannot release (20141107/utmutex-321)
Call Trace:
[<ffffffff81b0bd48>] dump_stack+0x4f/0x7b
[<ffffffff81546bf5>] acpi_ut_release_mutex+0x47/0x67
[<ffffffff81544357>] acpi_load_table+0x73/0xcb
Link: https://github.com/acpica/acpica/commit/c70434d4 Signed-off-by: Octavian Purdila <octavian.purdila@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We cap 32bit userspace backtraces to PERF_MAX_STACK_DEPTH
(currently 127), but we forgot to do the same for 64bit backtraces.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If we attempt to clone a 0 length region into a file we can end up
inserting a range in the inode's extent_io tree with a start offset
that is greater then the end offset, which triggers immediately the
following warning:
So just bail out of the clone ioctl if the length of the region to clone
is zero, without locking any extent range, in order to prevent this issue
(same behaviour as a pwrite with a 0 length for example).
This is trivial to reproduce. For example, the steps for the test I just
made for fstests:
mkfs.btrfs -f SCRATCH_DEV
mount SCRATCH_DEV $SCRATCH_MNT
If we pass a length of 0 to the extent_same ioctl, we end up locking an
extent range with a start offset greater then its end offset (if the
destination file's offset is greater than zero). This results in a warning
from extent_io.c:insert_state through the following call chain:
This leads to an infinite loop when evicting the inode. This is the same
problem that my previous patch titled
"Btrfs: fix inode eviction infinite loop after cloning into it" addressed
but for the extent_same ioctl instead of the clone ioctl.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Omar Sandoval <osandov@osandov.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Sebastian reported a crash caused by a jump label mismatch after resume.
This happens because we do not save the kernel text section during suspend
and therefore also do not restore it during resume, but use the kernel image
that restores the old system.
This means that after a suspend/resume cycle we lost all modifications done
to the kernel text section.
The reason for this is the pfn_is_nosave() function, which incorrectly
returns that read-only pages don't need to be saved. This is incorrect since
we mark the kernel text section read-only.
We still need to make sure to not save and restore pages contained within
NSS and DCSS segment.
To fix this add an extra case for the kernel text section and only save
those pages if they are not contained within an NSS segment.
Fixes the following crash (and the above bugs as well):
Reported-and-tested-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
- don't lock lp->lock in the iss_net_timer for the call of iss_net_poll,
it will lock it itself;
- invert order of lp->lock and opened_lock acquisition in the
iss_net_open to make it consistent with iss_net_poll;
- replace spin_lock with spin_lock_bh when acquiring locks used in
iss_net_timer from non-atomic context;
- replace spin_lock_irqsave with spin_lock_bh in the iss_net_start_xmit
as the driver doesn't use lp->lock in the hard IRQ context;
- replace __SPIN_LOCK_UNLOCKED(lp.lock) with spin_lock_init, otherwise
lockdep is unhappy about using non-static key.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
First check for rate == 0 in set_rate and round_rate to avoid div by zero.
Then, in order to get the closest rate, round all divisions to the closest
result instead of rounding them down.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Michael Turquette <mturquette@linaro.org>
[ luis: 3.16 prereq for: 4591243102fa "clk: at91: usb: propagate rate modification to the parent clk" ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The number of resets controls is 32 times the number of peripheral
register banks rather than 32 times the number of clocks. This reduces
(drastically) the number of reset controls registered from 10080 (315
clocks * 32) to 224 (6 peripheral register banks * 32).
This also fixes a potential crash because trying to use any of the
excess reset controls (224-10079) would have caused accesses beyond
the array bounds of the peripheral register banks definition array.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com> Cc: Prashant Gaikwad <pgaikwad@nvidia.com> Fixes: 6d5b988e7dc5 ("clk: tegra: implement a reset driver") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
memsize denotes the amount of RAM we can access from kseg{0,1} and
that should be up to 256M. In case the bootloader reports a value
higher than that (perhaps reporting all the available RAM) it's best
if we fix it ourselves and just warn the user about that. This is
usually a problem with the bootloader and/or its environment.
[ralf@linux-mips.org: Remove useless parens as suggested bei Sergei.
Reformat long pr_warn statement to fit into 80 column limit.]
The functions snd_emu10k1_proc_spdif_read and snd_emu1010_fpga_read
acquire the emu_lock before accessing the FPGA. The function used
to access the FPGA (snd_emu1010_fpga_read) also tries to take
the emu_lock which causes a deadlock.
Remove the outer locking in the proc-functions (guarding only the
already safe fpga read) to prevent this deadlock.
[removed superfluous flags variables too -- tiwai]
Signed-off-by: Michael Gernoth <michael@gernoth.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We may exit this function without properly freeing up the maapings
we may have acquired. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
img_ir_remove() passes a pointer to the ISR function as the 2nd
parameter to irq_free() instead of a pointer to the device data
structure.
This issue causes unloading img-ir module to fail with the below
warning after building and loading img-ir as a module.
Level IRQ handlers and edge IRQ handler are managed by tow different
sets of registers. But currently the driver uses the same mask for the
both registers. It lead to issues with the following scenario:
First, an IRQ is requested on a GPIO to be triggered on front. After,
this an other IRQ is requested for a GPIO of the same bank but
triggered on level. Then the first one will be also setup to be
triggered on level. It leads to an interrupt storm.
The different kind of handler are already associated with two
different irq chip type. With this patch the driver uses a private
mask for each one which solves this issue.
It has been tested on an Armada XP based board and on an Armada 375
board. For the both boards, with this patch is applied, there is no
such interrupt storm when running the previous scenario.
This bug was already fixed but in a different way in the legacy
version of this driver by Evgeniy Dushistov: 9ece8839b1277fb9128ff6833411614ab6c88d68 "ARM: orion: Fix for certain
sequence of request_irq can cause irq storm". The fact the new version
of the gpio drive could be affected had been discussed there:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012
Reported-by: Evgeniy A. Dushistov <dushistov@mail.ru> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If we were migrated right after __getcpu, but before reading the
migration_count, we wouldn't notice that we read TSC of a different
VCPU, nor that KVM's bug made pvti invalid, as only migration_count
on source VCPU is increased.
Change vdso instead of updating migration_count on destination.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Fixes: 0a4e6be9ca17 ("x86: kvm: Revert "remove sched notifier for cross-cpu migrations"")
Message-Id: <1428000263-11892-1-git-send-email-rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Before we reach to connection established we may get an
error event. In this case the core won't teardown this
connection (never established it), so we take care of freeing
it ourselves.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This hang was a result of a missing command put when
a DIF error occurred during a rdma read (and we sent
an CHECK_CONDITION error without passing it to the
backend).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
While this driver was already using a 50ms resume
timeout, let's make sure everybody uses the same
macro so it's easy to fix later should anything
go wrong.
It also gives a more "stable" expectation to Linux
users.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[ luis: backported to 3.16:
- replaced 'hub_wq' by 'khubd' in comment ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Based on original work by Bin Liu <Bin Liu <b-liu@ti.com>>
Cc: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
[ luis: backported to 3.16:
- only two msecs_to_jiffies() invocations
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[ luis: backported to 3.16:
- replaced 'hub_wq' by 'khubd' in comment ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Every USB Host controller should use this new
macro to define for how long resume signalling
should be driven on the bus.
Currently, almost every single USB controller
is using a 20ms timeout for resume signalling.
That's problematic for two reasons:
a) sometimes that 20ms timer expires a little
before 20ms, which makes us fail certification
b) some (many) devices actually need more than
20ms resume signalling.
Sure, in case of (b) we can state that the device
is against the USB spec, but the fact is that
we have no control over which device the certification
lab will use. We also have no control over which host
they will use. Most likely they'll be using a Windows
PC which, again, we have no control over how that
USB stack is written and how long resume signalling
they are using.
At the end of the day, we must make sure Linux passes
electrical compliance when working as Host or as Device
and currently we don't pass compliance as host because
we're driving resume signallig for exactly 20ms and
that confuses certification test setup resulting in
Certification failure.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk> Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Previously commit 14ece1028b3ed53ffec1b1213ffc6acaf79ad77c added a
support for for syncing parent directory of newly created inodes to
make sure that the inode is not lost after a power failure in
no-journal mode.
However this does not work in majority of cases, namely:
- if the directory has inline data
- if the directory is already indexed
- if the directory already has at least one block and:
- the new entry fits into it
- or we've successfully converted it to indexed
So in those cases we might lose the inode entirely even after fsync in
the no-journal mode. This also includes ext2 default mode obviously.
I've noticed this while running xfstest generic/321 and even though the
test should fail (we need to run fsck after a crash in no-journal mode)
I could not find a newly created entries even when if it was fsynced
before.
Fix this by adjusting the ext4_add_entry() successful exit paths to set
the inode EXT4_STATE_NEWENTRY so that fsync has the chance to fsync the
parent directory as well.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Frank Mayhar <fmayhar@google.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
- Remove the unneeded declaration from pnode.h
- Mark umount_tree static as it has no callers outside of namespace.c
- Define an enumeration of umount_tree's flags.
- Pass umount_tree's flags in by name
This removes the magic numbers 0, 1 and 2 making the code a little
clearer and makes it possible for there to be lazy unmounts that don't
propagate. Which is what __detach_mounts actually wants for example.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
[ luis: backported to 3.16:
- dropped change to __detach_mounts() ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The available (i.e. not used) buffers are returned by stk1160_clear_queue(),
on the stop_streaming() path. However, this is insufficient and the current
buffer must be released as well. Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The delay time after a reset in the codec probe callback was too short,
and did not work on certain hw because the codec needs more time to
power on. This increases the delay time from 1us to 1ms.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We found that TLB mismatch not only happens after kernel resume, but
also happens during snapshot restore. So move it to the beginning of
swsusp_arch_suspend().
Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9621/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Usually ELF_ET_DYN_BASE is 2/3 of TASK_SIZE. With 3G/1G user/kernel
split this is not so, because 2*TASK_SIZE overflows 32 bits,
so the actual value of ELF_ET_DYN_BASE is:
(2 * TASK_SIZE / 3) = 0x2a000000
When ASLR is disabled PIE binaries will load at ELF_ET_DYN_BASE address.
On 32bit platforms AddressSanitzer uses addresses [0x20000000 - 0x40000000]
for shadow memory [1]. So ASan doesn't work for PIE binaries when ASLR disabled
as it fails to map shadow memory.
Also after Kees's 'split ET_DYN ASLR from mmap ASLR' patchset PIE binaries
has a high chance of loading somewhere in between [0x2a000000 - 0x40000000]
even if ASLR enabled. This makes ASan with PIE absolutely incompatible.
Fix overflow by dividing TASK_SIZE prior to multiplying.
After this patch ELF_ET_DYN_BASE equals to (for CONFIG_VMSPLIT_3G=y):
(TASK_SIZE / 3 * 2) = 0x7f555554
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Reported-by: Maria Guseva <m.guseva@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Guest user mode can generate a guest MSA Disabled exception on an MSA
capable core by simply trying to execute an MSA instruction. Since this
exception is unknown to KVM it will be passed on to the guest kernel.
However guest Linux kernels prior to v3.15 do not set up an exception
handler for the MSA Disabled exception as they don't support any MSA
capable cores. This results in a guest OS panic.
Since an older processor ID may be being emulated, and MSA support is
not advertised to the guest, the correct behaviour is to generate a
Reserved Instruction exception in the guest kernel so it can send the
guest process an illegal instruction signal (SIGILL), as would happen
with a non-MSA-capable core.
Fix this as minimally as reasonably possible by preventing
kvm_mips_check_privilege() from relaying MSA Disabled exceptions from
guest user mode to the guest kernel, and handling the MSA Disabled
exception by emulating a Reserved Instruction exception in the guest,
via a new handle_msa_disabled() KVM callback.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org
[ luis: backported to 3.16: files renamed:
- arch/mips/kvm/emulate.c -> arch/mips/kvm/kvm_mips_emul.c
- arch/mips/kvm/mips.c -> arch/mips/kvm/kvm_mips.c] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
ie. the missing attribute name after the namespace.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94291 Reported-by: William Douglas <william.douglas@intel.com> Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
While committing a transaction we free the log roots before we write the
new super block. Freeing the log roots implies marking the disk location
of every node/leaf (metadata extent) as pinned before the new super block
is written. This is to prevent the disk location of log metadata extents
from being reused before the new super block is written, otherwise we
would have a corrupted log tree if before the new super block is written
a crash/reboot happens and the location of any log tree metadata extent
ended up being reused and rewritten.
Even though we pinned the log tree's metadata extents, we were issuing a
discard against them if the fs was mounted with the -o discard option,
resulting in corruption of the log tree if a crash/reboot happened before
writing the new super block - the next time the fs was mounted, during
the log replay process we would find nodes/leafs of the log btree with
a content full of zeroes, causing the process to fail and require the
use of the tool btrfs-zero-log to wipeout the log tree (and all data
previously fsynced becoming lost forever).
Fix this by not doing a discard when pinning an extent. The discard will
be done later when it's safe (after the new super block is committed) at
extent-tree.c:btrfs_finish_extent_commit().
Fixes: e688b7252f78 (Btrfs: fix extent pinning bugs in the tree log) Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This patch converts iscsi-target code to use modern kthread.h API
callers for creating RX/TX threads for each new iscsi_conn descriptor,
and releasing associated RX/TX threads during connection shutdown.
This is done using iscsit_start_kthreads() -> kthread_run() to start
new kthreads from within iscsi_post_login_handler(), and invoking
kthread_stop() from existing iscsit_close_connection() code.
Also, convert iscsit_logout_post_handler_closesession() code to use
cmpxchg when determing when iscsit_cause_connection_reinstatement()
needs to sleep waiting for completion.
There are two PMICs on Cragganmore, currently one dynamically assign
its IRQ base and the other uses a fixed base. It is possible for the
statically assigned PMIC to fail if its IRQ is taken by the dynamically
assigned one. Fix this by statically assigning both the IRQ bases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The comparison from the previous line seems to have been erroneously
(partially) copied-and-pasted onto the next. The second line should be
checking req.bytes, not req.lnum.
Coverity CID #139400
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[rw: Fixed comparison] Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In some of the 'out_not_moved' error paths, lnum may be used
uninitialized. Don't ignore the warning; let's fix it.
This uninitialized variable doesn't have much visible effect in the end,
since we just schedule the PEB for erasure, and its LEB number doesn't
really matter (it just gets printed in debug messages). But let's get it
straight anyway.
Coverity CID #113449
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the
PEB->LEB mapping.
Caught by Coverity, CID #711212.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We are completely discarding the earlier value of 'bitflips', which
could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the
bitwise OR of header and data 'bitflip' statuses instead.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
the lcd type as defined in the Kconfig is not matching in the code.
as a result the rs, rw and en pins were getting interchanged.
Kconfig defines the value of PANEL_LCD to be 1 if we select custom
configuration but in the code LCD_TYPE_CUSTOM is defined as 5.
my hardware is LCD_TYPE_CUSTOM, but the pins were assigned to it
as pins of LCD_TYPE_OLD, and it was not working.
Now values are corrected with referenece to the values defined in
Kconfig and it is working.
checked on JHD204A lcd with LCD_TYPE_CUSTOM configuration.
The WM8741 DAC supports the following typical audio sampling rates:
44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz)
32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz)
For the rates lists, we should use 82000 instead of 88235, 176400
instead of 1764000 and 192000 instead of 19200 (seems to be a typo).
Signed-off-by: Sergej Sawazki <ce3a@gmx.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It has come to my attention that this_cpu_read/write are horrible on
architectures other than x86. Worse yet, they actually disable
preemption or interrupts! This caused some unexpected tracing results
on ARM.
The ring_buffer_lock_reserve has recursion protection that requires
accessing a per cpu variable. But since preempt_disable() is traced, it
too got traced while accessing the variable that is suppose to prevent
recursion like this.
The generic version of this_cpu_read() and write() are:
#define this_cpu_generic_to_op(pcp, val, op) \
do { \
unsigned long flags; \
raw_local_irq_save(flags); \
*__this_cpu_ptr(&(pcp)) op val; \
raw_local_irq_restore(flags); \
} while (0)
Which is unacceptable for locations that know they are within preempt
disabled or interrupt disabled locations.
Paul McKenney stated that __this_cpu_() versions produce much better code on
other architectures than this_cpu_() does, if we know that the call is done in
a preempt disabled location.
I also changed the recursive_unlock() to use two local variables instead
of accessing the per_cpu variable twice.
HPET irq is routed to i8259 and then to MIPS CPU irq (cascade). After
commit a3e6c1eff5 (MIPS: IRQ: Fix disable_irq on CPU IRQs), if without
IRQF_NO_SUSPEND in cascade_irqaction, HPET interrupts will lost during
suspend. The result is machine cannot be waken up.
Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9528/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When a event PADDING is hit (a deleted event that is still in the ring
buffer), translate_data() sets the length of the padding and also updates
the data pointer which is passed back to the caller.
This is unneeded because the caller also updates the data pointer with
the passed back length. translate_data() should not update the pointer,
only set the length.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lkml.kernel.org/r/20150324135923.461431960@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The reset control for the sunxi mmc controller is optional. Some
newer platforms (sun6i, sun8i, sun9i) have it, while older ones
(sun4i, sun5i, sun7i) don't.
Use the properly stubbed _optional version so the driver does not
fail to compile when RESET_CONTROLLER=n.
This patch also adds a check for deferred probing on the reset
control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This is to ensure that 'alsactl restore' does not apply default
initialisation as the chip reset defaults are preferred.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The res parameter passed to devm_usb_phy_match() is the location where the
pointer to the usb_phy is stored, hence it needs to be dereferenced before
comparing to the match data in order to find the correct match.
Fixes: 410219dcd2ba ("usb: otg: utils: devres: Add API's to associate a device with the phy") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
69fb3676df33 ("x86 idle: remove mwait_idle() and "idle=mwait" cmdline param")
The reasoning was that modern machines should be sufficiently
happy during the boot process using the default_idle() HALT
loop, until cpuidle loads and either acpi_idle or intel_idle
invoke the newer MWAIT-with-hints idle loop.
But two machines reported problems:
1. Certain Core2-era machines support MWAIT-C1 and HALT only.
MWAIT-C1 is preferred for optimal power and performance.
But if they support just C1, cpuidle never loads and
so they use the boot-time default idle loop forever.
2. Some laptops will boot-hang if HALT is used,
but will boot successfully if MWAIT is used.
This appears to be a hidden assumption in BIOS SMI,
that is presumably valid on the proprietary OS
where the BIOS was validated.
https://bugzilla.kernel.org/show_bug.cgi?id=60770
So here we effectively revert the patch above, restoring
the mwait_idle() loop. However, we don't bother restoring
the idle=mwait cmdline parameter, since it appears to add
no value.
Maintainer notes:
For 3.9, simply revert 69fb3676df
for 3.10, patch -F3 applies, fuzz needed due to __cpuinit use in
context For 3.11, 3.12, 3.13, this patch applies cleanly
Tested-by: Mike Galbraith <bitbucket@online.de> Signed-off-by: Len Brown <len.brown@intel.com> Acked-by: Mike Galbraith <bitbucket@online.de> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Ian Malone <ibmalone@gmail.com> Cc: Josh Boyer <jwboyer@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/345254a551eb5a6a866e048d7ab570fd2193aca4.1389763084.git.len.brown@intel.com
[ Ported to recent kernels. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Mike Galbraith <efault@gmx.de>
[ luis: backported to 3.16: used Mike's backport to 3.10 and 3.14 ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The return value of power_supply_register() call was not checked and
even on error probe() function returned 0. If registering failed then
during unbind the driver tried to unregister power supply which was not
actually registered.
This could lead to memory corruption because power_supply_unregister()
unconditionally cleans up given power supply.
Fix this by checking return status of power_supply_register() call. In
case of failure, clean up sysfs entries and fail the probe.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 9be0fcb5ed46 ("compal-laptop: add JHL90, battery & hwmon interface") Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The commit c2be45f09bb0 ("compal-laptop: Use
devm_hwmon_device_register_with_groups") wanted to change the
registering of hwmon device to resource-managed version. It mostly did
it except the main thing - it forgot to use devm-like function so the
hwmon device leaked after device removal or probe failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: c2be45f09bb0 ("compal-laptop: Use devm_hwmon_device_register_with_groups") Acked-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Change the name of the hwmon interface from "compal-laptop" to "compal".
A dash is an invalid character for a hwmon name and caused the call to
hwmon_device_register_with_groups() to fail.
Signed-off-by: Roald Frederickx <roald.frederickx@gmail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Function-specific setup requests should be handled in such a way, that
apart from filling in the data buffer, the requests are also actually
enqueued: if function-specific setup is called from composte_setup(),
the "usb_ep_queue()" block of code in composite_setup() is skipped.
The printer function lacks this part and it results in e.g. get device id
requests failing: the host expects some response, the device prepares it
but does not equeue it for sending to the host, so the host finally asserts
timeout.
This patch adds enqueueing the prepared responses.
Fixes: 2e87edf49227: "usb: gadget: make g_printer use composite" Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
[ luis: backported to 3.16:
- file rename: drivers/usb/gadget/legacy/printer.c ->
drivers/usb/gadget/printer.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
