Fix the dp_panel_get_supported_bpp() API to return the minimum
supported bpp correctly for relevant cases and use this API
to correct the behavior of DP driver which hard-codes the max supported
bpp to 30.
This is incorrect because the number of lanes and max data rate
supported by the lanes need to be taken into account.
Replace the hardcoded limit with the appropriate math which accounts
for the accurate number of lanes and max data rate.
changes in v2:
- Fix the dp_panel_get_supported_bpp() and use it
- Drop the max_t usage as dp_panel_get_supported_bpp() already
returns the min_bpp correctly now
changes in v3:
- replace min_t with just min as all params are u32
DPU debugging macros need to be converted to a proper drm_debug_*
macros, however this is a going an intrusive patch, not suitable for a
fix. Wire DPU_DEBUG and DPU_DEBUG_DRIVER to always use DRM_DEBUG_DRIVER
to make sure that DPU debugging messages always end up in the drm debug
messages and are controlled via the usual drm.debug mask.
I don't think that it is a good idea for a generic DPU_DEBUG macro to be
tied to DRM_UT_KMS. It is used to report a debug message from driver, so by
default it should go to the DRM_UT_DRIVER channel. While refactoring
debug macros later on we might end up with particular messages going to
ATOMIC or KMS, but DRIVER should be the default.
iucv_alloc_device() gets a format string and a varying number of
arguments. This is incorrectly forwarded by calling dev_set_name() with
the format string and a va_list, while dev_set_name() expects also a
varying number of arguments.
Symptoms:
Corrupted iucv device names, which can result in log messages like:
sysfs: cannot create duplicate filename '/devices/iucv/hvc_iucv1827699952'
There is something wrong with ovs_drop_reasons. ovs_drop_reasons[0] is
"OVS_DROP_LAST_ACTION", but OVS_DROP_LAST_ACTION == __OVS_DROP_REASON + 1,
which means that ovs_drop_reasons[1] should be "OVS_DROP_LAST_ACTION".
And as Adrian tested, without the patch, adding flow to drop packets
results in:
drop at: do_execute_actions+0x197/0xb20 [openvsw (0xffffffffc0db6f97)
origin: software
input port ifindex: 8
timestamp: Tue Aug 20 10:19:17 2024 859853461 nsec
protocol: 0x800
length: 98
original length: 98
drop reason: OVS_DROP_ACTION_ERROR
With the patch, the same results in:
drop at: do_execute_actions+0x197/0xb20 [openvsw (0xffffffffc0db6f97)
origin: software
input port ifindex: 8
timestamp: Tue Aug 20 10:16:13 2024 475856608 nsec
protocol: 0x800
length: 98
original length: 98
drop reason: OVS_DROP_LAST_ACTION
Fix this by initializing ovs_drop_reasons with index.
Fixes: 9d802da40b7c ("net: openvswitch: add last-action drop reason") Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn> Tested-by: Adrian Moreno <amorenoz@redhat.com> Reviewed-by: Adrian Moreno <amorenoz@redhat.com> Link: https://patch.msgid.link/20240821123252.186305-1-dongml2@chinatelecom.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a multicast address is removed but there are still some multicast
addresses, that address would remain programmed into the frame filter.
Fix this by explicitly setting the enable bit for each filter.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240822154059.1066595-3-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If promiscuous mode is disabled when there are fewer than four multicast
addresses, then it will not be reflected in the hardware. Fix this by
always clearing the promiscuous mode flag even when we program multicast
addresses.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240822154059.1066595-2-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some CPT AF registers are per LF and others are global. Translation
of PF/VF local LF slot number to actual LF slot number is required
only for accessing perf LF registers. CPT AF global registers access
do not require any LF slot number. Also, there is no reason CPT
PF/VF to know actual lf's register offset.
Without this fix microcode loading will fail, VFs cannot be created
and hardware is not usable.
Fixes: bc35e28af789 ("octeontx2-af: replace cpt slot with lf id on reg write") Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240821070558.1020101-1-bbhushan2@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove the dma_unmap_page_attrs() call in the driver's XDP_REDIRECT
code path. This should have been removed when we let the page pool
handle the DMA mapping. This bug causes the warning:
Fixes: 578fcfd26e2a ("bnxt_en: Let the page pool manage the DMA mapping") Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20240820203415.168178-1-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After ip6_local_out() has returned, we no longer can safely
dereference rt, unless we hold rcu_read_lock().
A similar issue has been fixed in commit a688caa34beb ("ipv6: take rcu lock in rawv6_send_hdrinc()")
Another potential issue in ip6_finish_output2() is handled in a
separate patch.
[1]
BUG: KASAN: slab-use-after-free in ip6_send_skb+0x18d/0x230 net/ipv6/ip6_output.c:1964
Read of size 8 at addr ffff88806dde4858 by task syz.1.380/6530
When assembling fraglist GSO packets, udp4_gro_complete does not set
skb->csum_start, which makes the extra validation in __udp_gso_segment fail.
Fixes: 89add40066f9 ("net: drop bad gso csum_start and offset in virtio_net_hdr") Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20240819150621.59833-1-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a bug in netem_enqueue() introduced by
commit 5845f706388a ("net: netem: fix skb length BUG_ON in __skb_to_sgvec")
that can lead to a use-after-free.
This commit made netem_enqueue() always return NET_XMIT_SUCCESS
when a packet is duplicated, which can cause the parent qdisc's q.qlen
to be mistakenly incremented. When this happens qlen_notify() may be
skipped on the parent during destruction, leaving a dangling pointer
for some classful qdiscs like DRR.
There are two ways for the bug happen:
- If the duplicated packet is dropped by rootq->enqueue() and then
the original packet is also dropped.
- If rootq->enqueue() sends the duplicated packet to a different qdisc
and the original packet is dropped.
In both cases NET_XMIT_SUCCESS is returned even though no packets
are enqueued at the netem qdisc.
The fix is to defer the enqueue of the duplicate packet until after
the original packet has been guaranteed to return NET_XMIT_SUCCESS.
Fixes: 5845f706388a ("net: netem: fix skb length BUG_ON in __skb_to_sgvec") Reported-by: Budimir Markovic <markovicbudimir@gmail.com> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240819175753.5151-1-stephen@networkplumber.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sabrina reports that the igb driver does not cope well with large
MAX_SKB_FRAG values: setting MAX_SKB_FRAG to 45 causes payload
corruption on TX.
An easy reproducer is to run ssh to connect to the machine. With
MAX_SKB_FRAGS=17 it works, with MAX_SKB_FRAGS=45 it fails. This has
been reported originally in
https://bugzilla.redhat.com/show_bug.cgi?id=2265320
The root cause of the issue is that the driver does not take into
account properly the (possibly large) shared info size when selecting
the ring layout, and will try to fit two packets inside the same 4K
page even when the 1st fraglist will trump over the 2nd head.
Address the issue by checking if 2K buffers are insufficient.
Fixes: 3948b05950fd ("net: introduce a config option to tweak MAX_SKB_FRAGS") Reported-by: Jan Tluka <jtluka@redhat.com> Reported-by: Jirka Hladky <jhladky@redhat.com> Reported-by: Sabrina Dubroca <sd@queasysnail.net> Tested-by: Sabrina Dubroca <sd@queasysnail.net> Tested-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Link: https://patch.msgid.link/20240816152034.1453285-1-vinschen@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dpaa2_switch_add_bufs() function returns the number of bufs that it
was able to add. It returns BUFS_PER_CMD (7) for complete success or a
smaller number if there are not enough pages available. However, the
error checking is looking at the total number of bufs instead of the
number which were added on this iteration. Thus the error checking
only works correctly for the first iteration through the loop and
subsequent iterations are always counted as a success.
Fix this by checking only the bufs added in the current iteration.
Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://patch.msgid.link/eec27f30-b43f-42b6-b8ee-04a6f83423b6@stanley.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When working on multi-buffer packet on arch that has PAGE_SIZE >= 8192,
truesize is calculated and stored in xdp_buff::frame_sz per each
processed Rx buffer. This means that frame_sz will contain the truesize
based on last received buffer, but commit 1dc1a7e7f410 ("ice:
Centrallize Rx buffer recycling") assumed this value will be constant
for each buffer, which breaks the page recycling scheme and mess up the
way we update the page::page_offset.
To fix this, let us work on constant truesize when PAGE_SIZE >= 8192
instead of basing this on size of a packet read from Rx descriptor. This
way we can simplify the code and avoid calculating truesize per each
received frame and on top of that when using
xdp_update_skb_shared_info(), current formula for truesize update will
be valid.
This means ice_rx_frame_truesize() can be removed altogether.
Furthermore, first call to it within ice_clean_rx_irq() for 4k PAGE_SIZE
was redundant as xdp_buff::frame_sz is initialized via xdp_init_buff()
in ice_vsi_cfg_rxq(). This should have been removed at the point where
xdp_buff struct started to be a member of ice_rx_ring and it was no
longer a stack based variable.
There are two fixes tags as my understanding is that the first one
exposed us to broken truesize and page_offset handling and then second
introduced broken skb_shared_info update in ice_{construct,build}_skb().
Reported-and-tested-by: Luiz Capitulino <luizcap@redhat.com> Closes: https://lore.kernel.org/netdev/8f9e2a5c-fd30-4206-9311-946a06d031bb@redhat.com/ Fixes: 1dc1a7e7f410 ("ice: Centrallize Rx buffer recycling") Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Architectures that have PAGE_SIZE >= 8192 such as arm64 should act the
same as x86 currently, meaning reuse of a page should only take place
when no one else is busy with it.
Do two things independently of underlying PAGE_SIZE:
- store the page count under ice_rx_buf::pgcnt
- then act upon its value vs ice_rx_buf::pagecnt_bias when making the
decision regarding page reuse
Fixes: 2b245cb29421 ("ice: Implement transmit and NAPI support") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the active slave is cleared manually the xfrm state is not flushed.
This leads to xfrm add/del imbalance and adding the same state multiple
times. For example when the device cannot handle anymore states we get:
[ 1169.884811] bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
because it's filled with the same state after multiple active slave
clearings. This change also has a few nice side effects: user-space
gets a notification for the change, the old device gets its mac address
and promisc/mcast adjusted properly.
Fixes: 18cb261afd7b ("bonding: support hardware encryption offload to slaves") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We shouldn't set real_dev to NULL because packets can be in transit and
xfrm might call xdo_dev_offload_ok() in parallel. All callbacks assume
real_dev is set.
Example trace:
kernel: BUG: unable to handle page fault for address: 0000000000001030
kernel: bond0: (slave eni0np1): making interface the new active one
kernel: #PF: supervisor write access in kernel mode
kernel: #PF: error_code(0x0002) - not-present page
kernel: PGD 0 P4D 0
kernel: Oops: 0002 [#1] PREEMPT SMP
kernel: CPU: 4 PID: 2237 Comm: ping Not tainted 6.7.7+ #12
kernel: Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014
kernel: RIP: 0010:nsim_ipsec_offload_ok+0xc/0x20 [netdevsim]
kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
kernel: Code: e0 0f 0b 48 83 7f 38 00 74 de 0f 0b 48 8b 47 08 48 8b 37 48 8b 78 40 e9 b2 e5 9a d7 66 90 0f 1f 44 00 00 48 8b 86 80 02 00 00 <83> 80 30 10 00 00 01 b8 01 00 00 00 c3 0f 1f 80 00 00 00 00 0f 1f
kernel: bond0: (slave eni0np1): making interface the new active one
kernel: RSP: 0018:ffffabde81553b98 EFLAGS: 00010246
kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
kernel:
kernel: RAX: 0000000000000000 RBX: ffff9eb404e74900 RCX: ffff9eb403d97c60
kernel: RDX: ffffffffc090de10 RSI: ffff9eb404e74900 RDI: ffff9eb3c5de9e00
kernel: RBP: ffff9eb3c0a42000 R08: 0000000000000010 R09: 0000000000000014
kernel: R10: 7974203030303030 R11: 3030303030303030 R12: 0000000000000000
kernel: R13: ffff9eb3c5de9e00 R14: ffffabde81553cc8 R15: ffff9eb404c53000
kernel: FS: 00007f2a77a3ad00(0000) GS:ffff9eb43bd00000(0000) knlGS:0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: 0000000000001030 CR3: 00000001122ab000 CR4: 0000000000350ef0
kernel: bond0: (slave eni0np1): making interface the new active one
kernel: Call Trace:
kernel: <TASK>
kernel: ? __die+0x1f/0x60
kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
kernel: ? page_fault_oops+0x142/0x4c0
kernel: ? do_user_addr_fault+0x65/0x670
kernel: ? kvm_read_and_reset_apf_flags+0x3b/0x50
kernel: bond0: (slave eni0np1): making interface the new active one
kernel: ? exc_page_fault+0x7b/0x180
kernel: ? asm_exc_page_fault+0x22/0x30
kernel: ? nsim_bpf_uninit+0x50/0x50 [netdevsim]
kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
kernel: ? nsim_ipsec_offload_ok+0xc/0x20 [netdevsim]
kernel: bond0: (slave eni0np1): making interface the new active one
kernel: bond_ipsec_offload_ok+0x7b/0x90 [bonding]
kernel: xfrm_output+0x61/0x3b0
kernel: bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
kernel: ip_push_pending_frames+0x56/0x80
Fixes: 18cb261afd7b ("bonding: support hardware encryption offload to slaves") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We must check if there is an active slave before dereferencing the pointer.
Fixes: 18cb261afd7b ("bonding: support hardware encryption offload to slaves") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GRO code checks for matching layer 2 headers to see, if packet belongs
to the same flow and because ip6 tunnel set dev->hard_header_len
this check fails in cases, where it shouldn't. To fix this don't
set hard_header_len, but use needed_headroom like ipv4/ip_tunnel.c
does.
nft_counter_reset() resets the counter by subtracting the previously
retrieved value from the counter. This is a write operation on the
counter and as such it requires to be performed with a write sequence of
nft_counter_seq to serialize against its possible reader.
Update the packets/ bytes within write-sequence of nft_counter_seq.
Fixes: d84701ecbcd6a ("netfilter: nft_counter: rework atomic dump and reset") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sequence counter nft_counter_seq is a per-CPU counter. There is no
lock associated with it. nft_counter_do_eval() is using the same counter
and disables BH which suggest that it can be invoked from a softirq.
This in turn means that nft_counter_offload_stats(), which disables only
preemption, can be interrupted by nft_counter_do_eval() leading to two
writer for one seqcount_t.
This can lead to loosing stats or reading statistics while they are
updated.
Disable BH during stats update in nft_counter_offload_stats() to ensure
one writer at a time.
Fixes: b72920f6e4a9d ("netfilter: nftables: counter hardware offload support") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The buggy address belongs to the object at ffff0000ced0fc80
which belongs to the cache skbuff_head_cache of size 240
The buggy address is located 0 bytes inside of
freed 240-byte region [ffff0000ced0fc80, ffff0000ced0fd70)
Memory state around the buggy address: ffff0000ced0fb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff0000ced0fc00: fb fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc
>ffff0000ced0fc80: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff0000ced0fd00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc ffff0000ced0fd80: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb
In the MCTP route input test, we're routing one skb, then (when delivery
is expected) checking the resulting routed skb.
However, we're currently checking the original skb length, rather than
the routed skb. Check the routed skb instead; the original will have
been freed at this point.
Fixes: 8892c0490779 ("mctp: Add route input to socket tests") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/kernel-janitors/4ad204f0-94cf-46c5-bdab-49592addf315@kili.mountain/ Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240816-mctp-kunit-skb-fix-v1-1-3c367ac89c27@codeconstruct.com.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Its possible that two threads call tcp_sk_exit_batch() concurrently,
once from the cleanup_net workqueue, once from a task that failed to clone
a new netns. In the latter case, error unwinding calls the exit handlers
in reverse order for the 'failed' netns.
tcp_sk_exit_batch() calls tcp_twsk_purge().
Problem is that since commit b099ce2602d8 ("net: Batch inet_twsk_purge"),
this function picks up twsk in any dying netns, not just the one passed
in via exit_batch list.
This means that the error unwind of setup_net() can "steal" and destroy
timewait sockets belonging to the exiting netns.
This allows the netns exit worker to proceed to call
... because refcount_dec() of tw_refcount unexpectedly dropped to 0.
This doesn't seem like an actual bug (no tw sockets got lost and I don't
see a use-after-free) but as erroneous trigger of debug check.
Add a mutex to force strict ordering: the task that calls tcp_twsk_purge()
blocks other task from doing final _dec_and_test before mutex-owner has
removed all tw sockets of dying netns.
After commit d7db7775ea2e ("net: veth: do not manipulate GRO when using
XDP"), there is no need to load XDP program to enable GRO. On the other
hand, the current test is failed due to loading the XDP program. e.g.
# selftests: net: udpgro.sh
# ipv4
# no GRO ok
# no GRO chk cmsg ok
# GRO ./udpgso_bench_rx: recv: bad packet len, got 1472, expected 14720
#
# failed
[...]
# bad GRO lookup ok
# multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
#
# ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
#
# failed
ok 1 selftests: net: udpgro.sh
After fix, all the test passed.
# ./udpgro.sh
ipv4
no GRO ok
[...]
multiple GRO socks ok
Fixes: d7db7775ea2e ("net: veth: do not manipulate GRO when using XDP") Reported-by: Yi Chen <yiche@redhat.com> Closes: https://issues.redhat.com/browse/RHEL-53858 Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we only check the latest senders's exit code. If the receiver
report failed, it is not recoreded. Fix it by checking the exit code
of all the involved processes.
Before:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
0
After:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
1
Fixes: 3327a9c46352 ("selftests: add functionals test for UDP GRO") Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 255c1c7279ab ("tc-testing: Allow test cases to be skipped")
the variable test_ordinal doesn't exist in call_pre_case().
So it should not be accessed when an exception occurs.
This resolves the following splat:
...
During handling of the above exception, another exception occurred:
Traceback (most recent call last):
File ".../tdc.py", line 1028, in <module>
main()
File ".../tdc.py", line 1022, in main
set_operation_mode(pm, parser, args, remaining)
File ".../tdc.py", line 966, in set_operation_mode
catresults = test_runner_serial(pm, args, alltests)
File ".../tdc.py", line 642, in test_runner_serial
(index, tsr) = test_runner(pm, args, alltests)
File ".../tdc.py", line 536, in test_runner
res = run_one_test(pm, args, index, tidx)
File ".../tdc.py", line 419, in run_one_test
pm.call_pre_case(tidx)
File ".../tdc.py", line 146, in call_pre_case
print('test_ordinal is {}'.format(test_ordinal))
NameError: name 'test_ordinal' is not defined
Fixes: 255c1c7279ab ("tc-testing: Allow test cases to be skipped") Signed-off-by: Simon Horman <horms@kernel.org> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20240815-tdc-test-ordinal-v1-1-0255c122a427@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As explained by Horatiu Vultur in commit 603ead96582d ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are 2 distinct code paths (listed below) in the source code which
set up an injection header for Ocelot(-like) switches. Code path (2)
lacks the QoS class and source port being set correctly. Especially the
improper QoS classification is a problem for the "ocelot-8021q"
alternative DSA tagging protocol, because we support tc-taprio and each
packet needs to be scheduled precisely through its time slot. This
includes PTP, which is normally assigned to a traffic class other than
0, but would be sent through TC 0 nonetheless.
The code paths are:
(1) ocelot_xmit_common() from net/dsa/tag_ocelot.c - called only by the
standard "ocelot" DSA tagging protocol which uses NPI-based
injection - sets up bit fields in the tag manually to account for
a small difference (destination port offset) between Ocelot and
Seville. Namely, ocelot_ifh_set_dest() is omitted out of
ocelot_xmit_common(), because there's also seville_ifh_set_dest().
(2) ocelot_ifh_set_basic(), called by:
- ocelot_fdma_prepare_skb() for FDMA transmission of the ocelot
switchdev driver
- ocelot_port_xmit() -> ocelot_port_inject_frame() for
register-based transmission of the ocelot switchdev driver
- felix_port_deferred_xmit() -> ocelot_port_inject_frame() for the
DSA tagger ocelot-8021q when it must transmit PTP frames (also
through register-based injection).
sets the bit fields according to its own logic.
The problem is that (2) doesn't call ocelot_ifh_set_qos_class().
Copying that logic from ocelot_xmit_common() fixes that.
Unfortunately, although desirable, it is not easily possible to
de-duplicate code paths (1) and (2), and make net/dsa/tag_ocelot.c
directly call ocelot_ifh_set_basic()), because of the ocelot/seville
difference. This is the "minimal" fix with some logic duplicated (but
at least more consolidated).
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On an NXP LS1028A (felix DSA driver) with the following configuration:
- ocelot-8021q tagging protocol
- VLAN-aware bridge (with STP) spanning at least swp0 and swp1
- 8021q VLAN upper interfaces on swp0 and swp1: swp0.700, swp1.700
- ptp4l on swp0.700 and swp1.700
we see that the ptp4l instances do not see each other's traffic,
and they all go to the grand master state due to the
ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES condition.
Jumping to the conclusion for the impatient
-------------------------------------------
There is a zero-day bug in the ocelot switchdev driver in the way it
handles VLAN-tagged packet injection. The correct logic already exists in
the source code, in function ocelot_xmit_get_vlan_info() added by commit 5ca721c54d86 ("net: dsa: tag_ocelot: set the classified VLAN during xmit").
But it is used only for normal NPI-based injection with the DSA "ocelot"
tagging protocol. The other injection code paths (register-based and
FDMA-based) roll their own wrong logic. This affects and was noticed on
the DSA "ocelot-8021q" protocol because it uses register-based injection.
By moving ocelot_xmit_get_vlan_info() to a place that's common for both
the DSA tagger and the ocelot switch library, it can also be called from
ocelot_port_inject_frame() in ocelot.c.
We need to touch the lines with ocelot_ifh_port_set()'s prototype
anyway, so let's rename it to something clearer regarding what it does,
and add a kernel-doc. ocelot_ifh_set_basic() should do.
Investigation notes
-------------------
Debugging reveals that PTP event (aka those carrying timestamps, like
Sync) frames injected into swp0.700 (but also swp1.700) hit the wire
with two VLAN tags:
The second (unexpected) VLAN tag makes felix_check_xtr_pkt() ->
ptp_classify_raw() fail to see these as PTP packets at the link
partner's receiving end, and return PTP_CLASS_NONE (because the BPF
classifier is not written to expect 2 VLAN tags).
The reason why packets have 2 VLAN tags is because the transmission
code treats VLAN incorrectly.
Neither ocelot switchdev, nor felix DSA, declare the NETIF_F_HW_VLAN_CTAG_TX
feature. Therefore, at xmit time, all VLANs should be in the skb head,
and none should be in the hwaccel area. This is done by:
which does _not_ zero out skb->vlan_tci as seen by skb_vlan_tag_get().
This means that ocelot, when it calls skb_vlan_tag_get(), sees
(and uses) a residual skb->vlan_tci, while the same VLAN tag is
_already_ in the skb head.
The trivial fix for double VLAN headers is to replace the content of
ocelot_ifh_port_set() with:
if (skb_vlan_tag_present(skb))
ocelot_ifh_set_vlan_tci(ifh, skb_vlan_tag_get(skb));
but this would not be correct either, because, as mentioned,
vlan_hw_offload_capable() is false for us, so we'd be inserting dead
code and we'd always transmit packets with VID=0 in the injection frame
header.
I can't actually test the ocelot switchdev driver and rely exclusively
on code inspection, but I don't think traffic from 8021q uppers has ever
been injected properly, and not double-tagged. Thus I'm blaming the
introduction of VLAN fields in the injection header - early driver code.
As hinted at in the early conclusion, what we _want_ to happen for
VLAN transmission was already described once in commit 5ca721c54d86
("net: dsa: tag_ocelot: set the classified VLAN during xmit").
ocelot_xmit_get_vlan_info() intends to ensure that if the port through
which we're transmitting is under a VLAN-aware bridge, the outer VLAN
tag from the skb head is stripped from there and inserted into the
injection frame header (so that the packet is processed in hardware
through that actual VLAN). And in all other cases, the packet is sent
with VID=0 in the injection frame header, since the port is VLAN-unaware
and has logic to strip this VID on egress (making it invisible to the
wire).
Fixes: 08d02364b12f ("net: mscc: fix the injection header") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function hci_sched_le needs to update the respective counter variable
inplace other the likes of hci_quote_sent would attempt to use the
possible outdated value of conn->{le_cnt,acl_cnt}.
Link: https://github.com/bluez/bluez/issues/915 Fixes: 73d80deb7bdf ("Bluetooth: prioritizing data over HCI") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This inverts the LE State quirk so by default we assume the controllers
would report valid states rather than invalid which is how quirks
normally behave, also this would result in HCI command failing it the LE
States are really broken thus exposing the controllers that are really
broken in this respect.
Link: https://github.com/bluez/bluez/issues/584 Fixes: 220915857e29 ("Bluetooth: Adding driver and quirk defs for multi-role LE") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When trying to build compile_commands.json for an external module against
the kernel built in a separate output directory, the following error is
displayed:
make[1]: *** No rule to make target 'scripts/clang-tools/gen_compile_commands.py',
needed by 'compile_commands.json'. Stop.
This is because gen_compile_commands.py was previously looked up using a
relative path to $(srctree), but commit b1992c3772e6 ("kbuild: use
$(src) instead of $(srctree)/$(src) for source directory") stopped
defining VPATH for external module builds.
Prefixing gen_compile_commands.py with $(srctree) fixes the problem.
Fixes: b1992c3772e6 ("kbuild: use $(src) instead of $(srctree)/$(src) for source directory") Signed-off-by: Alexandre Courbot <gnurou@gmail.com> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The data conversion is done rather by a wrong function. We convert to
BE32, not from BE32. Although the end result must be same, this was
complained by the compiler.
Fix the code again and align with another similar function
tas2563_apply_calib() that does already right.
There is a small window in ssam_serial_hub_probe() where the controller
is initialized but has not been started yet. Specifically, between
ssam_controller_init() and ssam_controller_start(). Any failure in this
window, for example caused by a failure of serdev_device_open(),
currently results in an incorrect warning being emitted.
In particular, any failure in this window results in the controller
being destroyed via ssam_controller_destroy(). This function checks the
state of the controller and, in an attempt to validate that the
controller has been cleanly shut down before we try and deallocate any
resources, emits a warning if that state is not SSAM_CONTROLLER_STOPPED.
However, since we have only just initialized the controller and have not
yet started it, its state is SSAM_CONTROLLER_INITIALIZED. Note that this
is the only point at which the controller has this state, as it will
change after we start the controller with ssam_controller_start() and
never revert back. Further, at this point no communication has taken
place and the sender and receiver threads have not been started yet (and
we may not even have an open serdev device either).
Therefore, it is perfectly safe to call ssam_controller_destroy() with a
state of SSAM_CONTROLLER_INITIALIZED. This, however, means that the
warning currently being emitted is incorrect. Fix it by extending the
check.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20240811124645.246016-1-luzmaximilian@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In transmit path, it is likely that the iova is not aligned to PCIe TLP
max payload size, which is 128 for WCN7850. Normally in such cases hardware
is expected to split the packet into several parts in a manner such that
they, other than the first one, have aligned iova. However due to hardware
limitations, WCN7850 does not behave like that properly with some specific
unaligned iova in transmit path. This easily results in target hang in a
KPI transmit test: packet send/receive failure, WMI command send timeout
etc. Also fatal error seen in PCIe level:
Work around this by manually moving/reallocating payload buffer such that
we can map it to a 128 bytes aligned iova. The moving requires sufficient
head room or tail room in skb: for the former we can do ourselves a favor
by asking some extra bytes when registering with mac80211, while for the
latter we can do nothing.
Moving/reallocating buffer consumes additional CPU cycles, but the good news
is that an aligned iova increases PCIe efficiency. In my tests on some X86
platforms the KPI results are almost consistent.
Since this is seen only with WCN7850, add a new hardware parameter to
differentiate from others.
This commit changes device mapper, so that it returns -ERESTARTSYS
instead of -EINTR when it is interrupted by a signal (so that the ioctl
can be restarted).
The manpage signal(7) says that the ioctl function should be restarted if
the signal was handled with SA_RESTART.
Clang static checker (scan-build) warning:
cifsglob.h:line 890, column 3
Access to field 'ops' results in a dereference of a null pointer.
Commit 519be989717c ("cifs: Add a tracepoint to track credits involved in
R/W requests") adds a check for 'rdata->server', and let clang throw this
warning about NULL dereference.
When 'rdata->credits.value != 0 && rdata->server == NULL' happens,
add_credits_and_wake_if() will call rdata->server->ops->add_credits().
This will cause NULL dereference problem. Add a check for 'rdata->server'
to avoid NULL dereference.
Cc: stable@vger.kernel.org Fixes: 69c3c023af25 ("cifs: Implement netfslib hooks") Reviewed-by: David Howells <dhowells@redhat.com> Signed-off-by: Su Hui <suhui@nfschina.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a tracepoint to track the credit changes and server in_flight value
involved in the lifetime of a R/W request, logging it against the
request/subreq debugging ID. This requires the debugging IDs to be
recorded in the cifs_credits struct.
Also add a three-state flag to struct cifs_credits to note if we're
interested in determining when the in_flight contribution ends and, if so,
to track whether we've decremented the contribution yet.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 74c2ab6d653b ("smb/client: avoid possible NULL dereference in cifs_free_subrequest()") Signed-off-by: Sasha Levin <sashal@kernel.org>
After running once, the for_each_trip_desc() loop in
bang_bang_manage() is pure needless overhead because it is not going to
make any changes unless a new cooling device has been bound to one of
the trips in the thermal zone or the system is resuming from sleep.
For this reason, make bang_bang_manage() set governor_data for the
thermal zone and check it upfront to decide whether or not it needs to
do anything.
However, governor_data needs to be reset in some cases to let
bang_bang_manage() know that it should walk the trips again, so add an
.update_tz() callback to the governor and make the core additionally
invoke it during system resume.
To avoid affecting the other users of that callback unnecessarily, add
a special notification reason for system resume, THERMAL_TZ_RESUME, and
also pass it to __thermal_zone_device_update() called during system
resume for consistency.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Kästle <peter@piie.net> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Link: https://patch.msgid.link/2285575.iZASKD2KPV@rjwysocki.net Signed-off-by: Sasha Levin <sashal@kernel.org>
After recent changes, the Bang-bang governor may not adjust the
initial configuration of cooling devices to the actual situation.
Namely, if a cooling device bound to a certain trip point starts in
the "on" state and the thermal zone temperature is below the threshold
of that trip point, the trip point may never be crossed on the way up
in which case the state of the cooling device will never be adjusted
because the thermal core will never invoke the governor's
.trip_crossed() callback. [Note that there is no issue if the zone
temperature is at the trip threshold or above it to start with because
.trip_crossed() will be invoked then to indicate the start of thermal
mitigation for the given trip.]
To address this, add a .manage() callback to the Bang-bang governor
and use it to ensure that all of the thermal instances managed by the
governor have been initialized properly and the states of all of the
cooling devices involved have been adjusted to the current zone
temperature as appropriate.
Move the setting of the thermal instance target state from
bang_bang_control() into a separate function that will be also called
in a different place going forward.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Kästle <peter@piie.net> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Link: https://patch.msgid.link/3313587.aeNJFYEL58@rjwysocki.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Some cooling device target state checks in bang_bang_control()
done before setting the new target state are not necessary after
recent changes, so drop them.
Also avoid updating the target state before checking it for
unexpected values.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 84248e35d9b6 ("thermal: gov_bang_bang: Split bang_bang_control()") Signed-off-by: Sasha Levin <sashal@kernel.org>
OLED panels don't support the ABM, they shouldn't offer the
panel_power_savings attribute to the user. Check whether aux BL
control support was enabled to decide whether to offer it.
Reported-by: Gergo Koteles <soyer@irl.hu> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3359 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Tested-by: Gergo Koteles <soyer@irl.hu> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When interrupt is turned on while a lock holding by spin_lock_irq it
throws a warning because of potential deadlock.
blk_mq_prep_dispatch_rq
blk_mq_get_driver_tag
__blk_mq_get_driver_tag
__blk_mq_alloc_driver_tag
blk_mq_tag_busy -> tag is already busy
// failed to get driver tag
blk_mq_mark_tag_wait
spin_lock_irq(&wq->lock) -> lock A (&sbq->ws[i].wait)
__add_wait_queue(wq, wait) -> wait queue active
blk_mq_get_driver_tag
__blk_mq_tag_busy
-> 1) tag must be idle, which means there can't be inflight IO
spin_lock_irq(&tags->lock) -> lock B (hctx->tags)
spin_unlock_irq(&tags->lock) -> unlock B, turn on interrupt accidentally
-> 2) context must be preempt by IO interrupt to trigger deadlock.
As shown above, the deadlock is not possible in theory, but the warning
still need to be fixed.
Fix it by using spin_lock_irqsave to get lockB instead of spin_lock_irq.
Fixes: 4f1731df60f9 ("blk-mq: fix potential io hang by wrong 'wake_batch'") Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240815024736.2040971-1-lilingfeng@huaweicloud.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, kasan_init_sw_tags() is called before setup_per_cpu_areas(),
so per_cpu(prng_state, cpu) accesses the same address regardless of the
value of "cpu", and the same seed value gets copied to the percpu area
for every CPU. Fix this by moving the call to smp_prepare_boot_cpu(),
which is the first architecture hook after setup_per_cpu_areas().
Fixes: 3c9e3aa11094 ("kasan: add tag related helper functions") Fixes: 3f41b6093823 ("kasan: fix random seed generation for tag-based mode") Signed-off-by: Samuel Holland <samuel.holland@sifive.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Link: https://lore.kernel.org/r/20240814091005.969756-1-samuel.holland@sifive.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 779dbc2e78d7 ("printk: Avoid non-panic CPUs writing
to ringbuffer") disabled non-panic CPUs to further write messages to
ringbuffer after panicked.
Since the commit, non-panicked CPU's are not allowed to write to
ring buffer after panicked and CPU backtrace which is triggered
after panicked to sample non-panicked CPUs' backtrace no longer
serves its function as it has nothing to print.
Fix the issue by allowing non-panicked CPUs to write into ringbuffer
while CPU backtrace is in flight.
Fixes: 779dbc2e78d7 ("printk: Avoid non-panic CPUs writing to ringbuffer") Signed-off-by: Ryo Takakura <takakura@valinux.co.jp> Reviewed-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20240812072703.339690-1-takakura@valinux.co.jp Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
topology_is_core_online() checks if the core a CPU belongs to
is online. The core is online if at least one of the sibling
CPUs is online. The first CPU of an online core is also online
in the common case, so this should be fairly quick.
If a core is offline then enabling SMT should not online CPUs of
this core. By enabling SMT, what is intended is either changing the SMT
value from "off" to "on" or setting the SMT level (threads per core) from a
lower to higher value.
On PowerPC the ppc64_cpu utility can be used, among other things, to
perform the following functions:
ppc64_cpu --cores-on # Get the number of online cores
ppc64_cpu --cores-on=X # Put exactly X cores online
ppc64_cpu --offline-cores=X[,Y,...] # Put specified cores offline
ppc64_cpu --smt={on|off|value} # Enable, disable or change SMT level
If the user has decided to offline certain cores, enabling SMT should
not online CPUs in those cores. This patch fixes the issue and changes
the behaviour as described, by introducing an arch specific function
topology_is_core_online(). It is currently implemented only for PowerPC.
It's more natural to use ktime/ns instead of keeping around usec,
especially since we're comparing it against user provided timers,
so convert napi busy poll internal handling to ktime. It's also nicer
since the type (ktime_t vs unsigned long) now tells the unit of measure.
Keep everything as ktime, which we convert to/from micro seconds for
IORING_[UN]REGISTER_NAPI. The net/ busy polling works seems to work with
usec, however it's not real usec as shift by 10 is used to get it from
nsecs, see busy_loop_current_time(), so it's easy to get truncated nsec
back and we get back better precision.
Note, we can further improve it later by removing the truncation and
maybe convincing net/ to use ktime/ns instead.
Since the do_div() macro casts the divisor to u32 anyway, remove the
unnecessary s64 cast and fix the following Coccinelle/coccicheck
warning reported by do_div.cocci:
WARNING: do_div() does a 64-by-32 division, please consider using div64_s64 instead
This reverts commit bc792884b76f ("s390/dasd: Establish DMA alignment").
Quoting the original commit:
linux-next commit bf8d08532bc1 ("iomap: add support for dma aligned
direct-io") changes the alignment requirement to come from the block
device rather than the block size, and the default alignment
requirement is 512-byte boundaries. Since DASD I/O has page
alignments for IDAW/TIDAW requests, let's override this value to
restore the expected behavior.
I mentioned TIDAW, but that was wrong. TIDAWs have no distinct alignment
requirement (per p. 15-70 of POPS SA22-7832-13):
Unless otherwise specified, TIDAWs may designate
a block of main storage on any boundary and length
up to 4K bytes, provided the specified block does not
cross a 4 K-byte boundary.
IDAWs do, but the original commit neglected that while ECKD DASD are
typically formatted in 4096-byte blocks, they don't HAVE to be. Formatting
an ECKD volume with smaller blocks is permitted (dasdfmt -b xxx), and the
problematic commit enforces alignment properties to such a device that
will result in errors, such as:
The original commit omitted the FBA discipline for just this reason,
but the formatted block size of the other disciplines was overlooked.
The solution to all of this is to revert to the original behavior,
such that the block size can be respected. There were two commits [1]
that moved this code in the interim, so a straight git-revert is not
possible, but the change is straightforward.
But what of the original problem? That was manifested with a direct-io
QEMU guest, where QEMU itself was changed a month or two later with
commit 25474d90aa ("block: use the request length for iov alignment")
such that the blamed kernel commit is unnecessary.
[1] commit 0127a47f58c6 ("dasd: move queue setup to common code")
commit fde07a4d74e3 ("dasd: use the atomic queue limits API")
Fixes: bc792884b76f ("s390/dasd: Establish DMA alignment") Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Link: https://lore.kernel.org/r/20240812125733.126431-2-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Another oddity in these config entries is their default value can fall
back to 'n', which is a value for bool or tristate symbols.
The '|| echo n' is an incorrect workaround to avoid the syntax error.
This is not a big deal, as the entry is hidden by 'depends on RUST' in
situations where '$(RUSTC) --version' or '$(BINDGEN) --version' fails.
Anyway, it looks odd.
The default of a string type symbol should be a double-quoted string
literal. Turn it into an empty string when the version command fails.
Fixes: 2f7ab1267dc9 ("Kbuild: add Rust support") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Link: https://lore.kernel.org/r/20240727140302.1806011-2-masahiroy@kernel.org
[ Rebased on top of v6.11-rc1. - Miguel ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When enabling UBSAN on Raspberry Pi 5, we get the following warning:
[ 387.894977] UBSAN: array-index-out-of-bounds in drivers/gpu/drm/v3d/v3d_sched.c:320:3
[ 387.903868] index 7 is out of range for type '__u32 [7]'
[ 387.909692] CPU: 0 PID: 1207 Comm: kworker/u16:2 Tainted: G WC 6.10.3-v8-16k-numa #151
[ 387.919166] Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT)
[ 387.925961] Workqueue: v3d_csd drm_sched_run_job_work [gpu_sched]
[ 387.932525] Call trace:
[ 387.935296] dump_backtrace+0x170/0x1b8
[ 387.939403] show_stack+0x20/0x38
[ 387.942907] dump_stack_lvl+0x90/0xd0
[ 387.946785] dump_stack+0x18/0x28
[ 387.950301] __ubsan_handle_out_of_bounds+0x98/0xd0
[ 387.955383] v3d_csd_job_run+0x3a8/0x438 [v3d]
[ 387.960707] drm_sched_run_job_work+0x520/0x6d0 [gpu_sched]
[ 387.966862] process_one_work+0x62c/0xb48
[ 387.971296] worker_thread+0x468/0x5b0
[ 387.975317] kthread+0x1c4/0x1e0
[ 387.978818] ret_from_fork+0x10/0x20
[ 387.983014] ---[ end trace ]---
This happens because the UAPI provides only seven configuration
registers and we are reading the eighth position of this u32 array.
Therefore, fix the out-of-bounds read in `v3d_csd_job_run()` by
accessing only seven positions on the '__u32 [7]' array. The eighth
register exists indeed on V3D 7.1, but it isn't currently used. That
being so, let's guarantee that it remains unused and add a note that it
could be set in a future patch.
Fix noise from speakers connected to AUX port when no sound is playing.
The problem occurs because the `alc_shutup_pins` function includes
a 0x10ec0257 vendor ID, which causes noise on Lenovo IdeaPad 3 15IAU7 with
Realtek ALC257 codec when no sound is playing.
Removing this vendor ID from the function fixes the bug.
Fixes: 70794b9563fe ("ALSA: hda/realtek: Add more codec ID to no shutup pins list") Signed-off-by: Parsa Poorshikhian <parsa.poorsh@gmail.com> Link: https://patch.msgid.link/20240810150939.330693-1-parsa.poorsh@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
During Linux graceful reboot, the GPIO interrupts are not disabled.
Since the drivers are not removed during graceful reboot,
the logic to call mlxbf3_gpio_irq_disable() is not triggered.
Interrupts that remain enabled can cause issues on subsequent boots.
For example, the mlxbf-gige driver contains PHY logic to bring up the link.
If the gpio-mlxbf3 driver loads first, the mlxbf-gige driver
will use a GPIO interrupt to bring up the link.
Otherwise, it will use polling.
The next time Linux boots and loads the drivers in this order, we encounter the issue:
- mlxbf-gige loads first and uses polling while the GPIO10
interrupt is still enabled from the previous boot. So if
the interrupt triggers, there is nothing to clear it.
- gpio-mlxbf3 loads.
- i2c-mlxbf loads. The interrupt doesn't trigger for I2C
because it is shared with the GPIO interrupt line which
was not cleared.
The solution is to add a shutdown function to the GPIO driver to clear and disable
all interrupts. Also clear the interrupt after disabling it in mlxbf3_gpio_irq_disable().
With CONFIG_LTO_CLANG=y, the compiler may add .llvm.<hash> suffix to
function names to avoid duplication. APIs like kallsyms_lookup_name()
and kallsyms_on_each_match_symbol() tries to match these symbol names
without the .llvm.<hash> suffix, e.g., match "c_stop" with symbol
c_stop.llvm.17132674095431275852. This turned out to be problematic
for use cases that require exact match, for example, livepatch.
Fix this by making the APIs to match symbols exactly.
Also cleanup kallsyms_selftests accordingly.
Signed-off-by: Song Liu <song@kernel.org> Fixes: 8cc32a9bbf29 ("kallsyms: strip LTO-only suffixes from promoted global functions") Tested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Acked-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20240807220513.3100483-3-song@kernel.org Signed-off-by: Kees Cook <kees@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reimplements commit 951bcae6c5a0 ("kallsyms: Avoid weak references
for kallsyms symbols") because I am not a big fan of PROVIDE().
As an alternative solution, this commit prepends one more kallsyms step.
KSYMS .tmp_vmlinux.kallsyms0.S # added
AS .tmp_vmlinux.kallsyms0.o # added
LD .tmp_vmlinux.btf
BTF .btf.vmlinux.bin.o
LD .tmp_vmlinux.kallsyms1
NM .tmp_vmlinux.kallsyms1.syms
KSYMS .tmp_vmlinux.kallsyms1.S
AS .tmp_vmlinux.kallsyms1.o
LD .tmp_vmlinux.kallsyms2
NM .tmp_vmlinux.kallsyms2.syms
KSYMS .tmp_vmlinux.kallsyms2.S
AS .tmp_vmlinux.kallsyms2.o
LD vmlinux
Step 0 takes /dev/null as input, and generates .tmp_vmlinux.kallsyms0.o,
which has a valid kallsyms format with the empty symbol list, and can be
linked to vmlinux. Since it is really small, the added compile-time cost
is negligible.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Stable-dep-of: 020925ce9299 ("kallsyms: Do not cleanup .llvm.<hash> suffix before sorting symbols") Signed-off-by: Sasha Levin <sashal@kernel.org>
- Specify the extra objects directly in vmlinux_link()
- Move the AS rule to kallsyms()
- Set kallsymso and btf_vmlinux_bin_o where they are generated
- Remove unneeded variable, kallsymso_prev
- Introduce the btf_data variable
- Introduce the strip_debug flag instead of checking the output name
No functional change intended.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Stable-dep-of: 020925ce9299 ("kallsyms: Do not cleanup .llvm.<hash> suffix before sorting symbols") Signed-off-by: Sasha Levin <sashal@kernel.org>
When config TC during the reset process, may cause a deadlock, the flow is
as below:
pf reset start
│
▼
......
setup tc │
│ ▼
▼ DOWN: napi_disable()
napi_disable()(skip) │
│ │
▼ ▼
...... ......
│ │
▼ │
napi_enable() │
▼
UINIT: netif_napi_del()
│
▼
......
│
▼
INIT: netif_napi_add()
│
▼
...... global reset start
│ │
▼ ▼
UP: napi_enable()(skip) ......
│ │
▼ ▼
...... napi_disable()
In reset process, the driver will DOWN the port and then UINIT, in this
case, the setup tc process will UP the port before UINIT, so cause the
problem. Adds a DOWN process in UINIT to fix it.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Consider the followed case that the user change speed and reset the net
interface. Before the hw change speed successfully, the driver get old
old speed from hw by timer task. After reset, the previous speed is config
to hw. As a result, the new speed is configed successfully but lost after
PF reset. The followed pictured shows more dirrectly.
Currently, if hns3 PF or VF FLR reset failed after five times retry,
the reset done process will directly release the semaphore
which has already released in hclge_reset_prepare_general.
This will cause down operation fail.
So this patch fixes it by adding reset state judgement. The up operation is
only called after successful PF FLR reset.
Fixes: 8627bdedc435 ("net: hns3: refactor the precedure of PF FLR") Fixes: f28368bb4542 ("net: hns3: refactor the procedure of VF FLR") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When deleting netns, it is possible to still have some tasks running,
e.g. background tasks like tcpdump running in the background, not
stopped because the test has been interrupted.
Before deleting the netns, it is then safer to kill all attached PIDs,
if any. That should reduce some noises after the end of some tests, and
help with the debugging of some issues. That's why this modification is
seen as a "fix".
After a vsock socket has been added to a BPF sockmap, its prot->recvmsg
has been replaced with vsock_bpf_recvmsg(). Thus the following
recursiion could happen:
vsock_bpf_recvmsg()
-> __vsock_recvmsg()
-> vsock_connectible_recvmsg()
-> prot->recvmsg()
-> vsock_bpf_recvmsg() again
We need to fix it by calling the original ->recvmsg() without any BPF
sockmap logic in __vsock_recvmsg().
Fixes: 634f1a7110b4 ("vsock: support sockmap") Reported-by: syzbot+bdb4bd87b5e22058e2a4@syzkaller.appspotmail.com Tested-by: syzbot+bdb4bd87b5e22058e2a4@syzkaller.appspotmail.com Cc: Bobby Eshleman <bobby.eshleman@bytedance.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://patch.msgid.link/20240812022153.86512-1-xiyou.wangcong@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Objects' dump callbacks are not concurrency-safe per-se with reset bit
set. If two CPUs perform a reset at the same time, at least counter and
quota objects suffer from value underrun.
Prevent this by introducing dedicated locking callbacks for nfnetlink
and the asynchronous dump handling to serialize access.
Fixes: 43da04a593d8 ("netfilter: nf_tables: atomic dump and reset for stateful objects") Signed-off-by: Phil Sutter <phil@nwl.cc> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In theory, dumpreset may fail and invalidate the preceeding log message.
Fix this and use the occasion to prepare for object reset locking, which
benefits from a few unrelated changes:
* Add an early call to nfnetlink_unicast if not resetting which
effectively skips the audit logging but also unindents it.
* Extract the table's name from the netlink attribute (which is verified
via earlier table lookup) to not rely upon validity of the looked up
table pointer.
* Do not use local variable family, it will vanish.
Commit 264640fc2c5f4 ("ipv6: distinguish frag queues by device
for multicast and link-local packets") modified the ipv6 fragment
reassembly logic to distinguish frag queues by device for multicast
and link-local packets but in fact only the main reassembly code
limits the use of the device to those address types and the netfilter
reassembly code uses the device for all packets.
This means that if fragments of a packet arrive on different interfaces
then netfilter will fail to reassemble them and the fragments will be
expired without going any further through the filters.
Fixes: 648700f76b03 ("inet: frags: use rhashtables for reassembly units") Signed-off-by: Tom Hughes <tom@compton.nu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is based on the discussions between Neal Cardwell and
Eric Dumazet in the link
https://lore.kernel.org/netdev/20240726204105.1466841-1-quic_subashab@quicinc.com/
It was correctly pointed out that tp->window_clamp would not be
updated in cases where net.ipv4.tcp_moderate_rcvbuf=0 or if
(copied <= tp->rcvq_space.space). While it is expected for most
setups to leave the sysctl enabled, the latter condition may
not end up hitting depending on the TCP receive queue size and
the pattern of arriving data.
The updated check should be hit only on initial MSS update from
TCP_MIN_MSS to measured MSS value and subsequently if there was
an update to a larger value.
Fixes: 05f76b2d634e ("tcp: Adjust clamping window for applications specifying SO_RCVBUF") Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com> Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ssn_offset field is u32 and is placed into the netlink response with
nla_put_u32(), but only 2 bytes are reserved for the attribute payload
in subflow_get_info_size() (even though it makes no difference
in the end, as it is aligned up to 4 bytes). Supply the correct
argument to the relevant nla_total_size() call to make it less
confusing.
A recent change to the driver exposed a bug where the MAC RX
filters (unicast MAC, broadcast MAC, and multicast MAC) are
configured and enabled before the RX path is fully initialized.
The result of this bug is that after the PHY is started packets
that match these MAC RX filters start to flow into the RX FIFO.
And then, after rx_init() is completed, these packets will go
into the driver RX ring as well. If enough packets are received
to fill the RX ring (default size is 128 packets) before the call
to request_irq() completes, the driver RX function becomes stuck.
This bug is intermittent but is most likely to be seen where the
oob_net0 interface is connected to a busy network with lots of
broadcast and multicast traffic.
All the MAC RX filters must be disabled until the RX path is ready,
i.e. all initialization is done and all the IRQs are installed.
Fixes: f7442a634ac0 ("mlxbf_gige: call request_irq() after NAPI initialized") Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Signed-off-by: David Thompson <davthompson@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
In axiethernet header fix register defines comment description to be
inline with IP documentation. It updates MAC configuration register,
MDIO configuration register and frame filter control description.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
