During xfrm migration copy replay and preplay sequence numbers
from the previous state.
Here is a tcpdump output showing the problem.
10.0.10.46 is running vanilla kernel, is the IKE/IPsec responder.
After the migration it sent wrong sequence number, reset to 1.
The migration is from 10.0.0.52 to 10.0.0.53.
IP 10.0.0.52.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7cf), length 136
IP 10.0.10.46.4500 > 10.0.0.52.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x7cf), length 136
IP 10.0.0.52.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d0), length 136
IP 10.0.10.46.4500 > 10.0.0.52.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x7d0), length 136
IP 10.0.0.53.4500 > 10.0.10.46.4500: NONESP-encap: isakmp: child_sa inf2[I]
IP 10.0.10.46.4500 > 10.0.0.53.4500: NONESP-encap: isakmp: child_sa inf2[R]
IP 10.0.0.53.4500 > 10.0.10.46.4500: NONESP-encap: isakmp: child_sa inf2[I]
IP 10.0.10.46.4500 > 10.0.0.53.4500: NONESP-encap: isakmp: child_sa inf2[R]
IP 10.0.0.53.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d1), length 136
NOTE: next sequence is wrong 0x1
IP 10.0.10.46.4500 > 10.0.0.53.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x1), length 136
IP 10.0.0.53.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d2), length 136
IP 10.0.10.46.4500 > 10.0.0.53.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x2), length 136
The tm-resched-dscr test has started failing sometimes, depending on
what compiler it's built with, eg:
test: tm_resched_dscr
Check DSCR TM context switch: tm-resched-dscr: tm-resched-dscr.c:76: test_body: Assertion `rv' failed.
!! child died by signal 6
When it fails we see that the compiler doesn't initialise rv to 1 before
entering the inline asm block. Although that's counter intuitive, it
is allowed because we tell the compiler that the inline asm will write
to rv (using "=r"), meaning the original value is irrelevant.
Marking it as a read/write parameter would presumably work, but it seems
simpler to fix it by setting the initial value of rv in the inline asm.
Fixes: 96d016108640 ("powerpc: Correct DSCR during TM context switch") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AR5K_EEPROM_READ macro returns with -EIO if a read error
occurs causing a memory leak on the allocated buffer buf. Fix
this by explicitly calling ath5k_hw_nvram_read and exiting on
the via the freebuf label that performs the necessary free'ing
of buf when a read error occurs.
Detected by CoverityScan, CID#1248782 ("Resource Leak")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the SCSI residue is not
reported correctly. The residue is initialized to 0, but this value
is overwritten whenever the driver sends firmware to the card reader
before performing the current command. As a result, a valid READ or
WRITE operation appears to have failed, causing the SCSI core to retry
the command multiple times and eventually fail.
This patch fixes the problem by resetting the SCSI residue to 0 after
sending firmware to the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function x25_init is not properly unregister related resources
on error handler.It is will result in kernel oops if x25_init init
failed, so add properly unregister call on error handler.
Also, i adjust the coding style and make x25_register_sysctl properly
return failure.
Signed-off-by: linzhang <xiaolou4617@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the ene_transport()
routine is supposed to initialize the driver before executing the
current command, if the initialization has not already been performed.
However, a bug in the routine causes it to skip the command after
doing the initialization. Also, the routine does not return an
appropriate error code if either the initialization or the command
fails.
As a result of the first bug, the first command (a SCSI INQUIRY) is
not carried out. The results can be seen in the system log, in the
form of a warning message and empty or garbage INQUIRY data:
Apr 18 22:40:08 notebook2 kernel: scsi host6: scsi scan: INQUIRY result too short (5), using 36
Apr 18 22:40:08 notebook2 kernel: scsi 6:0:0:0: Direct-Access PQ: 0 ANSI: 0
This patch fixes both errors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ci_hdrc_host_init() or ci_hdrc_gadget_init() returns error and the
error != -ENXIO, as Peter pointed out, "it stands for initialization
for host or gadget has failed", so we'd better return failure rather
continue.
And before destroying the otg, i.e ci_hdrc_otg_destroy(ci), we should
also check ci->roles[CI_ROLE_GADGET].
It's a common practice to send gratuitous ARPs after moving an
IP address to another device to speed up healing of a service. To
fulfill service availability constraints, the timing of network peers
updating their caches to point to a new location of an IP address can be
particularly important.
Sometimes neigh_update calls won't touch neither lladdr nor state, for
example if an update arrives in locktime interval. The neigh->updated
value is tested by the protocol specific neigh code, which in turn
will influence whether NEIGH_UPDATE_F_OVERRIDE gets set in the
call to neigh_update() or not. As a result, we may effectively ignore
the update request, bailing out of touching the neigh entry, except that
we still bump its timestamps inside neigh_update.
This may be a problem for updates arriving in quick succession. For
example, consider the following scenario:
A service is moved to another device with its IP address. The new device
sends three gratuitous ARP requests into the network with ~1 seconds
interval between them. Just before the first request arrives to one of
network peer nodes, its neigh entry for the IP address transitions from
STALE to DELAY. This transition, among other things, updates
neigh->updated. Once the kernel receives the first gratuitous ARP, it
ignores it because its arrival time is inside the locktime interval. The
kernel still bumps neigh->updated. Then the second gratuitous ARP
request arrives, and it's also ignored because it's still in the (new)
locktime interval. Same happens for the third request. The node
eventually heals itself (after delay_first_probe_time seconds since the
initial transition to DELAY state), but it just wasted some time and
require a new ARP request/reply round trip. This unfortunate behaviour
both puts more load on the network, as well as reduces service
availability.
This patch changes neigh_update so that it bumps neigh->updated (as well
as neigh->confirmed) only once we are sure that either lladdr or entry
state will change). In the scenario described above, it means that the
second gratuitous ARP request will actually update the entry lladdr.
Ideally, we would update the neigh entry on the very first gratuitous
ARP request. The locktime mechanism is designed to ignore ARP updates in
a short timeframe after a previous ARP update was honoured by the kernel
layer. This would require tracking timestamps for state transitions
separately from timestamps when actual updates are received. This would
probably involve changes in neighbour struct. Therefore, the patch
doesn't tackle the issue of the first gratuitous APR ignored, leaving
it for a follow-up.
Signed-off-by: Ihar Hrachyshka <ihrachys@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When platform_get_irq() fails, it returns an error code, which
libahci_platform and replaces it by -EINVAL. This commit fixes that by
propagating the error code. It fixes the situation where
platform_get_irq() returns -EPROBE_DEFER because the interrupt
controller is not available yet, and generally looks like the right
thing to do.
We pay attention to not show the "no irq" message when we are in an
EPROBE_DEFER situation, because the driver probing will be retried
later on, once the interrupt controller becomes available to provide
the interrupt.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The setting of return code ret should be based on the error code
passed into function end_extent_writepage and not on ret. Thanks
to Liu Bo for spotting this mistake in the original fix I submitted.
Detected by CoverityScan, CID#1414312 ("Logically dead code")
Fixes: 5dca6eea91653e ("Btrfs: mark mapping with error flag to report errors to userspace") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function devm_clk_get() returns an ERR_PTR when it fails. However, in
function kdwc3_probe(), its return value is not checked, which may
result in a bad memory access bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA_PREP_FENCE is to be used when preparing Tx descriptor if output
of Tx descriptor is to be used by next/dependent Tx descriptor.
The DMA_PREP_FENSE will not be set correctly in do_async_gen_syndrome()
when calling dma->device_prep_dma_pq() under following conditions:
1. ASYNC_TX_FENCE not set in submit->flags
2. DMA_PREP_FENCE not set in dma_flags
3. src_cnt (= (disks - 2)) is greater than dma_maxpq(dma, dma_flags)
This patch fixes DMA_PREP_FENCE usage in do_async_gen_syndrome() taking
inspiration from do_async_xor() implementation.
Signed-off-by: Anup Patel <anup.patel@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every address gets added with TENTATIVE flag even for the addresses with
IFA_F_NODAD flag and dad-work is scheduled for them. During this DAD process
we realize it's an address with NODAD and complete the process without
sending any probe. However the TENTATIVE flags stays on the
address for sometime enough to cause misinterpretation when we receive a NS.
While processing NS, if the address has TENTATIVE flag, we mark it DADFAILED
and endup with an address that was originally configured as NODAD with
DADFAILED.
We can't avoid scheduling dad_work for addresses with NODAD but we can
avoid adding TENTATIVE flag to avoid this racy situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running a stress playback/stop loop test on a mx6wandboard channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Since the clocksource watchdog will only detect broken TSC after the
fact, all TSC based clocks will likely have observed non-continuous
values before/when switching away from TSC.
Therefore only thing to fully avoid random clock movement when your
BIOS randomly mucks with TSC values from SMI handlers is reporting the
TSC as unstable at boot.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: wlan-ng: prism2mgmt.c: This patches fixes a double endian conversion.
cpu_to_le16() was called twice first in prism2mgmt_scan and again inside
hfa384x_drvr_setconfig16() for the same variable, hence it was swapped
twice. Incidentally, it also fixed the following sparse warning:
drivers/staging/wlan-ng/prism2mgmt.c:173:30: warning: incorrect type in assignment (different base types)
drivers/staging/wlan-ng/prism2mgmt.c:173:30: expected unsigned short [unsigned] [usertype] word
drivers/staging/wlan-ng/prism2mgmt.c:173:30: got restricted __le16 [usertype] <noident>
Unfortunately, only compile tested.
Signed-off-by: Andrea della Porta <sfaragnaus@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code we accidentally return the successful result from
idr_alloc() instead of a negative error pointer. The caller is looking
for an error pointer and so it treats the returned value as a valid
pointer.
This one might be a bit serious because if it lets people get around the
kernel's protection for remapping NULL. I'm not sure.
Fixes: 75d2364ea0ca (PowerCap: Add class driver) Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several paths in vmxnet3, where settings changes cause the
adapter to be brought down and back up (vmxnet3_set_ringparam among
them). Should part of the reset operation fail, these paths call
vmxnet3_force_close, which enables all napi instances prior to calling
dev_close (with the expectation that vmxnet3_close will then properly
disable them again). However, vmxnet3_force_close neglects to clear
VMXNET3_STATE_BIT_QUIESCED prior to calling dev_close. As a result
vmxnet3_quiesce_dev (called from vmxnet3_close), returns early, and
leaves all the napi instances in a enabled state while the device itself
is closed. If a device in this state is activated again, napi_enable
will be called on already enabled napi_instances, leading to a BUG halt.
The fix is to simply enausre that the QUIESCED bit is cleared in
vmxnet3_force_close to allow quesence to be completed properly on close.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Shrikrishna Khare <skhare@vmware.com> CC: "VMware, Inc." <pv-drivers@vmware.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PR KVM implementation of the PAPR HPT hypercalls (H_ENTER etc.)
access an image of the HPT in userspace memory using copy_from_user
and copy_to_user. Recently, the declarations of those functions were
annotated to indicate that the return value must be checked. Since
this code doesn't currently check the return value, this causes
compile warnings like the ones shown below, and since on PPC the
default is to compile arch/powerpc with -Werror, this causes the
build to fail.
To fix this, we check the return values, and if non-zero, fail the
hypercall being processed with a H_FUNCTION error return value.
There is really no good error return value to use since PAPR didn't
envisage the possibility that the hypervisor may not be able to access
the guest's HPT, and H_FUNCTION (function not supported) seems as
good as any.
The typical compile warnings look like this:
CC arch/powerpc/kvm/book3s_pr_papr.o
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c: In function ‘kvmppc_h_pr_enter’:
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c:53:2: error: ignoring return value of ‘copy_from_user’, declared with attribute warn_unused_result [-Werror=unused-result]
copy_from_user(pteg, (void __user *)pteg_addr, sizeof(pteg));
^
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c:74:2: error: ignoring return value of ‘copy_to_user’, declared with attribute warn_unused_result [-Werror=unused-result]
copy_to_user((void __user *)pteg_addr, hpte, HPTE_SIZE);
^
Currently rcode is being initialized to NX_RCODE_SUCCESS and later it
is checked to see if it is not NX_RCODE_SUCCESS which is never true. It
appears that there is an unintentional missing assignment of rcode from
the return of the call to netxen_issue_cmd() that was dropped in
an earlier fix, so add it in.
Detected by CoverityScan, CID#401900 ("Logically dead code")
Fixes: 2dcd5d95ad6b2 ("netxen_nic: fix cdrp race condition") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qca_spi driver causes alignment issues on ARM devices.
So fix this by using netdev_alloc_skb_ip_align().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cifs_relock_file() can perform a down_write() on the inode's lock_sem even
though it was already performed in cifs_strict_readv(). Lockdep complains
about this. AFAICS, there is no problem here, and lockdep just needs to be
told that this nesting is OK.
=============================================
[ INFO: possible recursive locking detected ]
4.11.0+ #20 Not tainted
---------------------------------------------
cat/701 is trying to acquire lock:
(&cifsi->lock_sem){++++.+}, at: cifs_reopen_file+0x7a7/0xc00
but task is already holding lock:
(&cifsi->lock_sem){++++.+}, at: cifs_strict_readv+0x177/0x310
other info that might help us debug this:
Possible unsafe locking scenario:
Signed-off-by: Rabin Vincent <rabinv@axis.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The perf tool assumes that kernel symbols are never present at address
zero. In fact it assumes if functions that map symbols to addresses
return zero, that the symbol was not found.
Given that s390's _text symbol historically is located at address zero
this yields at least a couple of false errors and warnings in one of
perf's test cases about not present symbols ("perf test 1").
To fix this simply move the _text symbol to address 0x200, just behind
the initial psw and channel program located at the beginning of the
kernel image. This is now hard coded within the linker script.
I tried a nicer solution which moves the initial psw and channel
program into an own section. However that would move the symbols
within the "real" head.text section to different addresses, since the
".org" statements within head.S are relative to the head.text
section. If there is a new section in front, everything else will be
moved. Alternatively I could have adjusted all ".org" statements. But
this current solution seems to be the easiest one, since nobody really
cares where the _text symbol is actually located.
alloc_pidmap() advances pid_namespace::last_pid. When first pid
allocation fails, then next created process will have pid 2 and
pid_ns_prepare_proc() won't be called. So, pid_namespace::proc_mnt will
never be initialized (not to mention that there won't be a child
reaper).
I saw crash stack of such case on kernel 3.10:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: proc_flush_task+0x8f/0x1b0
Call Trace:
release_task+0x3f/0x490
wait_consider_task.part.10+0x7ff/0xb00
do_wait+0x11f/0x280
SyS_wait4+0x7d/0x110
We may fix this by restore of last_pid in 0 or by prohibiting of futher
allocations. Since there was a similar issue in Oleg Nesterov's commit 314a8ad0f18a ("pidns: fix free_pid() to handle the first fork failure").
and it was fixed via prohibiting allocation, let's follow this way, and
do the same.
Link: http://lkml.kernel.org/r/149201021004.4863.6762095011554287922.stgit@localhost.localdomain Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Andrei Vagin <avagin@virtuozzo.com> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michael Kerrisk <mtk.manpages@googlemail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul Moore <paul@paul-moore.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Ingo Molnar <mingo@kernel.org> Cc: Serge Hallyn <serge@hallyn.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by David Jeffery: "a signal was sent to lockd while lockd
was shutting down from a request to stop nfs. The signal causes lockd
to call restart_grace() which puts the lockd_net structure on the grace
list. If this signal is received at the wrong time, it will occur after
lockd_down_net() has called locks_end_grace() but before
lockd_down_net() stops the lockd thread. This leads to lockd putting
the lockd_net structure back on the grace list, then exiting without
anything removing it from the list."
So, perform the final locks_end_grace() from the the lockd thread; this
ensures it's serialized with respect to restart_grace().
Reported-by: David Jeffery <djeffery@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When users set flow control using ethtool the bits are set properly in the
CPGMAC_SL MACCONTROL register, but the FIFO depth in the respective Port n
Maximum FIFO Blocks (Pn_MAX_BLKS) registers remains set to the minimum size
reset value. When receive flow control is enabled on a port, the port's
associated FIFO block allocation must be adjusted. The port RX allocation
must increase to accommodate the flow control runout. The TRM recommends
numbers of 5 or 6.
Hence, apply required Port FIFO configuration to
Pn_MAX_BLKS.Pn_TX_MAX_BLKS=0xF and Pn_MAX_BLKS.Pn_RX_MAX_BLKS=0x5 during
interface initialization.
Cc: Schuyler Patton <spatton@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using memcpy() from a string that is shorter than the length copied means
the destination buffer is being filled with arbitrary data from the kernel
rodata segment. Instead, use strncpy() which will fill the trailing bytes
with zeros.
This was found with the future CONFIG_FORTIFY_SOURCE feature.
Cc: Daniel Micay <danielmicay@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using memcpy() from a string that is shorter than the length copied means
the destination buffer is being filled with arbitrary data from the kernel
rodata segment. Instead, use strncpy() which will fill the trailing bytes
with zeros.
This was found with the future CONFIG_FORTIFY_SOURCE feature.
Cc: Daniel Micay <danielmicay@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ieee80211_hw_restart() is called during authentication, the
authentication process will continue, causing the driver to be called
in a wrong state. This ultimately causes an oops in the iwlwifi
driver (at least).
The sadb_x_sec_len is stored in the unit 'byte divided by eight'.
So we have to multiply this value by eight before we can do
size checks. Otherwise we may get a slab-out-of-bounds when
we memcpy the user sec_ctx.
Let the target core check the CMD_T_ABORTED flag instead of the SRP
target driver. Hence remove the transport_check_aborted_status()
call. Since state == SRPT_STATE_CMD_RSP_SENT is something that really
should not happen, do not try to recover if srpt_queue_response() is
called for an I/O context that is in that state. This patch is a bug
fix because the srpt_abort_cmd() call is misplaced - if that function
is called from srpt_queue_response() it should either be called
before the command state is changed or after the response has been
sent.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Cc: Doug Ledford <dledford@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Cc: David Disseldorp <ddiss@suse.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the server returns NFS4ERR_CONN_NOT_BOUND_TO_SESSION because we
are trunking, then RECLAIM_COMPLETE must handle that by calling
nfs4_schedule_session_recovery() and then retrying.
Reported-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Tested-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Andrew F. Davis <afd@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Andrew F. Davis <afd@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to set "first = 0' at the end of rdev_for_each
loop, so we can get the array's min_offset_diff correctly
otherwise min_offset_diff just means the last rdev's
offset diff.
[only the first chunk, due to b506335e5d2b ("md/raid10: skip spare disk as
'first' disk") being already applied - gregkh]
GPIO7 is configured in POWERHOLD mode which has higher priority
over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON
bit is turned off. This property enables driver to over ride the
POWERHOLD value to GPIO7 so as to turn off the PMIC in power off
scenarios.
Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ECMA-48 [1] (aka ISO 6429) has defined SGR 21 as "doubly underlined"
since at least March 1984. The Linux kernel has treated it as SGR 22
"normal intensity" since it was added in Linux-0.96b in June 1992.
Before that, it was simply ignored. Other terminal emulators have
either ignored it, or treat it as double underline now. xterm for
example added support in its 304 release (May 2014) [2] where it was
previously ignoring it.
Changing this behavior shouldn't be an issue:
- It isn't a named capability in ncurses's terminfo database, so no
script is using libtinfo/libcurses to look this up, or using tput
to query & output the right sequence.
- Any script assuming SGR 21 will reset intensity in all terminals
already do not work correctly on non-Linux VTs (including running
under screen/tmux/etc...).
- If someone has written a script that only runs in the Linux VT, and
they're using SGR 21 (instead of SGR 22), the output should still
be readable.
imo it's important to change this as the Linux VT's non-conformance
is sometimes used as an argument for other terminal emulators to not
implement SGR 21 at all, or do so incorrectly.
The touch sensor buttons on Sony VAIO VGN-CS series laptops (e.g.
VGN-CS31S) are a separate PS/2 device. As the MUX is disabled for all
VAIO machines by the nomux blacklist, the data from touch sensor
buttons and touchpad are combined. The protocol used by the buttons is
probably similar to the touchpad protocol (both are Synaptics) so both
devices get enabled. The controller combines the data, creating a mess
which results in random button clicks, touchpad stopping working and
lost sync error messages:
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 4
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: issuing reconnect request
Add a new i8042_dmi_forcemux_table whitelist with VGN-CS.
With MUX enabled, touch sensor buttons are detected as separate device
(and left disabled as there's currently no driver), fixing all touchpad
problems.
Reset i8042 before probing because of insufficient BIOS initialisation of
the i8042 serial controller. This makes Synaptics touchpad detection
possible. Without resetting the Synaptics touchpad is not detected because
there are always NACK messages from AUX port.
Originally, /proc/PID/task/TID/maps was the same as /proc/TID/maps.
In current kernels, /proc/PID/maps (or /proc/TID/maps even for
threads) shows "[stack]" for VMAs in the mm's stack address range.
In contrast, /proc/PID/task/TID/maps uses KSTK_ESP to guess the
target thread's stack's VMA. This is racy, probably returns garbage
and, on arches with CONFIG_TASK_INFO_IN_THREAD=y, is also crash-prone:
KSTK_ESP is not safe to use on tasks that aren't known to be running
ordinary process-context kernel code.
This patch removes the difference and just shows "[stack]" for VMAs
in the mm's stack range. This is IMO much more sensible -- the
actual "stack" address really is treated specially by the VM code,
and the current thread stack isn't even well-defined for programs
that frequently switch stacks on their own.
Reported-by: Jann Horn <jann@thejh.net> Signed-off-by: Andy Lutomirski <luto@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Linux API <linux-api@vger.kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Tycho Andersen <tycho.andersen@canonical.com> Link: http://lkml.kernel.org/r/3e678474ec14e0a0ec34c611016753eea2e1b8ba.1475257877.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b76437579d13 ("procfs: mark thread stack correctly in
proc/<pid>/maps") added [stack:TID] annotation to /proc/<pid>/maps.
Finding the task of a stack VMA requires walking the entire thread list,
turning this into quadratic behavior: a thousand threads means a
thousand stacks, so the rendering of /proc/<pid>/maps needs to look at a
million combinations.
The cost is not in proportion to the usefulness as described in the
patch.
Drop the [stack:TID] annotation to make /proc/<pid>/maps (and
/proc/<pid>/numa_maps) usable again for higher thread counts.
The [stack] annotation inside /proc/<pid>/task/<tid>/maps is retained, as
identifying the stack VMA there is an O(1) operation.
Siddesh said:
"The end users needed a way to identify thread stacks programmatically and
there wasn't a way to do that. I'm afraid I no longer remember (or have
access to the resources that would aid my memory since I changed
employers) the details of their requirement. However, I did do this on my
own time because I thought it was an interesting project for me and nobody
really gave any feedback then as to its utility, so as far as I am
concerned you could roll back the main thread maps information since the
information is available in the thread-specific files"
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Siddhesh Poyarekar <siddhesh.poyarekar@gmail.com> Cc: Shaohua Li <shli@fb.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ecb-cast5-avx, if a 128+ byte scatterlist element followed a
shorter one, then the algorithm accidentally encrypted/decrypted only 8
bytes instead of the expected 128 bytes. Fix it by setting the
encryption/decryption 'fn' correctly.
Fixes: c12ab20b162c ("crypto: cast5/avx - avoid using temporary stack buffers") Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have an unaligned SG list entry where there is no leftover
aligned data, the hash walk code will incorrectly return zero as if
the entire SG list has been processed.
This patch fixes it by moving onto the next page instead.
Reported-by: Eli Cooper <elicooper@gmx.com> Cc: <stable@vger.kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WCH CH382L is a PCI-E adapter with 1 parallel port. It is similair to CH382
but serial ports are not soldered on board. Detected as
Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850])
It looks like there is a double-free vulnerability in Linux usbtv driver
on an error path of usbtv_probe function. When audio registration fails,
usbtv_video_free function ends up freeing usbtv data structure, which
gets freed the second time under usbtv_video_fail label.
Currently the driver spams the kernel log on unsupported ioctls which is
unnecessary as the ioctl returns -ENOIOCTLCMD to indicate this anyway.
I suspect this was originally for debugging purposes but it really is not
required so remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: Major Hayden <major@mhtx.net> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans Verkuil [Wed, 28 Mar 2018 18:12:34 +0000 (15:12 -0300)]
media: v4l2-ctrls: fix sparse warning
The warning is simple:
drivers/media/v4l2-core/v4l2-ctrls.c:1685:15: warning: incorrect type in assignment (different address spaces)
but the fix isn't.
The core problem was that the conversion from user to kernelspace was
done at too low a level and that needed to be moved up. That made it possible
to drop pointers to v4l2_ext_control from set_ctrl and validate_new and
clean up this sparse warning because those functions now always operate
on kernelspace pointers.
The 32-bit compat v4l2 ioctl handling is implemented based on its 64-bit
equivalent. It converts 32-bit data structures into its 64-bit
equivalents and needs to provide the data to the 64-bit ioctl in user
space memory which is commonly allocated using
compat_alloc_user_space().
However, due to how that function is implemented, it can only be called
a single time for every syscall invocation.
Supposedly to avoid this limitation, the existing code uses a mix of
memory from the kernel stack and memory allocated through
compat_alloc_user_space().
Under normal circumstances, this would not work, because the 64-bit
ioctl expects all pointers to point to user space memory. As a
workaround, set_fs(KERNEL_DS) is called to temporarily disable this
extra safety check and allow kernel pointers. However, this might
introduce a security vulnerability: The result of the 32-bit to 64-bit
conversion is writeable by user space because the output buffer has been
allocated via compat_alloc_user_space(). A malicious user space process
could then manipulate pointers inside this output buffer, and due to the
previous set_fs(KERNEL_DS) call, functions like get_user() or put_user()
no longer prevent kernel memory access.
The new approach is to pre-calculate the total amount of user space
memory that is needed, allocate it using compat_alloc_user_space() and
then divide up the allocated memory to accommodate all data structures
that need to be converted.
An alternative approach would have been to retain the union type karg
that they allocated on the kernel stack in do_video_ioctl(), copy all
data from user space into karg and then back to user space. However, we
decided against this approach because it does not align with other
compat syscall implementations. Instead, we tried to replicate the
get_user/put_user pairs as found in other places in the kernel:
if (get_user(clipcount, &up->clipcount) ||
put_user(clipcount, &kp->clipcount)) return -EFAULT;
Clearly nobody could be bothered to upstream this patch or at minimum
tell us :-( We only heard about this a week ago.
This patch was rebased and cleaned up. Compared to the original I
also swapped the order of the convert_in_user arguments so that they
matched copy_in_user. It was hard to review otherwise. I also replaced
the ALLOC_USER_SPACE/ALLOC_AND_GET by a normal function.
Fixes: 6b5a9492ca ("v4l: introduce string control support.") Signed-off-by: Daniel Mentz <danielmentz@google.com> Co-developed-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ioctls need to copy back the result even if the ioctl returned
an error. However, don't do this for the error code -ENOTTY.
It makes no sense in that cases.
There is nothing wrong with using an unknown buffer type. So
stop spamming the kernel log whenever this happens. The kernel
will just return -EINVAL to signal this.
Commit b2787845fb91 ("V4L/DVB (5289): Add support for video output
overlays.") added the field global_alpha to struct v4l2_window but did
not update the compat layer accordingly. This change adds global_alpha
to struct v4l2_window32 and copies the value for global_alpha back and
forth.
If the device is of type VFL_TYPE_SUBDEV then vdev->ioctl_ops
is NULL so the 'if (!ops->vidioc_query_ext_ctrl)' check would crash.
Add a test for !ops to the condition.
All sub-devices that have controls will use the control framework,
so they do not have an equivalent to ops->vidioc_query_ext_ctrl.
Returning false if ops is NULL is the correct thing to do here.
ctrl_is_pointer just hardcoded two known string controls, but that
caused problems when using e.g. custom controls that use a pointer
for the payload.
Reimplement this function: it now finds the v4l2_ctrl (if the driver
uses the control framework) or it calls vidioc_query_ext_ctrl (if the
driver implements that directly).
In both cases it can now check if the control is a pointer control
or not.
Instead of doing sizeof(struct foo) use sizeof(*up). There even were
cases where 4 * sizeof(__u32) was used instead of sizeof(kp->reserved),
which is very dangerous when the size of the reserved array changes.
If Security Request is received on connection that is already encrypted
with sufficient security master should perform encryption key refresh
procedure instead of just ignoring Slave Security Request
(Core Spec 5.0 Vol 3 Part H 2.4.6).
> ACL Data RX: Handle 3585 flags 0x02 dlen 6
SMP: Security Request (0x0b) len 1
Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
Handle: 3585
Random number: 0x0000000000000000
Encrypted diversifier: 0x0000
Long term key: 44264272a5c426a9e868f034cf0e69f3
> HCI Event: Command Status (0x0f) plen 4
LE Start Encryption (0x08|0x0019) ncmd 1
Status: Success (0x00)
> HCI Event: Encryption Key Refresh Complete (0x30) plen 3
Status: Success (0x00)
Handle: 3585
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
commit c4585a2823edf ("bridge: ebt_among: add missing match size checks")
added validation for pool size, but missed fact that the macros
ebt_among_wh_src/dst can already return out-of-bound result because
they do not check value of wh_src/dst_ofs (an offset) vs. the size
of the match that userspace gave to us.
v2:
check that offset has correct alignment.
Paolo Abeni points out that we should also check that src/dst
wormhash arrays do not overlap, and src + length lines up with
start of dst (or vice versa).
v3: compact wormhash_sizes_valid() part
NB: Fixes tag is intentionally wrong, this bug exists from day
one when match was added for 2.6 kernel. Tag is there so stable
maintainers will notice this one too.
Tested with same rules from the earlier patch.
Fixes: c4585a2823edf ("bridge: ebt_among: add missing match size checks") Reported-by: <syzbot+bdabab6f1983a03fc009@syzkaller.appspotmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't have a compat layer for xfrm, so userspace and kernel
structures have different sizes in this case. This results in
a broken configuration, so refuse to configure socket policies
when trying to insert from 32 bit userspace as we do it already
with policies inserted via netlink.
f7c83bcbfaf5 ("net: xfrm: use __this_cpu_read per-cpu helper") added a
__this_cpu_read() call inside ipcomp_alloc_tfms().
At the time, __this_cpu_read() required the caller to either not care
about races or to handle preemption/interrupt issues. 3.15 tightened
the rules around some per-cpu operations, and now __this_cpu_read()
should never be used in a preemptible context. On 3.15 and later, we
need to use this_cpu_read() instead.
syzkaller reported this leading to the following kernel BUG while
fuzzing sendmsg:
The sanity test added in ecd7918745234 can be bypassed, validation
only occurs if XFRM_STATE_ESN flag is set, but rest of code doesn't care
and just checks if the attribute itself is present.
So always validate. Alternative is to reject if we have the attribute
without the flag but that would change abi.
Reported-by: syzbot+0ab777c27d2bb7588f73@syzkaller.appspotmail.com Cc: Mathias Krause <minipli@googlemail.com> Fixes: ecd7918745234 ("xfrm_user: ensure user supplied esn replay window is valid") Fixes: d8647b79c3b7e ("xfrm: Add user interface for esn and big anti-replay windows") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kprobes to set(recover) RWX bits correctly on trampoline
buffer before releasing it. Releasing readonly page to
module_memfree() crash the kernel.
Without this fix, if kprobes user register a bunch of kprobes
in function body (since kprobes on function entry usually
use ftrace) and unregister it, kernel hits a BUG and crash.
Link: http://lkml.kernel.org/r/149570868652.3518.14120169373590420503.stgit@devbox Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Fixes: d0381c81c2f7 ("kprobes/x86: Set kprobes pages read-only") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Thu, 11 Jan 2018 17:01:36 +0000 (17:01 +0000)]
xhci: Fix ring leak in failure path of xhci_alloc_virt_device()
This is a stable-only fix for the backport of commit 5d9b70f7d52e
("xhci: Don't add a virt_dev to the devs array before it's fully
allocated").
In branches that predate commit c5628a2af83a ("xhci: remove endpoint
ring cache") there is an additional failure path in
xhci_alloc_virt_device() where ring cache allocation fails, in
which case we need to free the ring allocated for endpoint 0.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Mathias Nyman <mathias.nyman@intel.com> Cc: Wang Han <wanghan1995315@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: Matthieu CASTET <matthieu.castet@parrot.com> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Wang Han <wanghan1995315@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we unlock our spinlock to copy data to user we may get
disabled by USB host and free the whole list of completed out
requests including the one from which we are copying the data
to user memory.
To prevent from this let's remove our working element from
the list and place it back only if there is sth left when we
finish with it.
Fixes: 99c515005857 ("usb: gadget: hidg: register OUT INT endpoint for SET_REPORT") Cc: stable@vger.kernel.org Tested-by: David Lechner <david@lechnology.com> Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Jerry Zhang <zhangjerry@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using usb_ep_align() makes sure that the buffer size for OUT endpoints is
always aligned with wMaxPacketSize (512 usually). This makes sure
that no buffer has the wrong size, which can cause nasty bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB spec specifies wMaxPacketSize to be little endian (as other properties),
so when using this variable in the driver we should convert to the current
CPU endianness if necessary.
This patch also introduces usb_ep_align() which does always returns the
aligned buffer size for an endpoint. This is useful to be used by USB requests
allocator functions.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Length of buffers should be of type size_t whenever possible. Altough
recommended, this change has no real practical change, unless a driver has a
uses a huge or negative buffer size - it might help find these bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is shared between gadget functions, so this avoid unnecessary
duplicated code and potentially avoid memory leaks.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe F. Tonello <eu@felipetonello.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UFS partitions from newer versions of FreeBSD 10 and 11 use relative
addressing for their subpartitions. But older versions of FreeBSD still
use absolute addressing just like OpenBSD and NetBSD.
Instead of simply testing for a FreeBSD partition, the code needs to
also test if the starting offset of the C subpartition is zero.
Annoyingly, modify_user_hw_breakpoint() unnecessarily complicates the
modification of a breakpoint - simplify it and remove the pointless
local variables.
Also update the stale Docbook while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to use the driver (e.g. aplay *.wav), the 4MiB DMA buffer
will get mmapp'ed in 16KiB chunks. But this fails with the 2nd 16KiB
area, as the page offset is outside of the VMA range (size), which is
currently used as size parameter in snd_pcm_lib_default_mmap(). By
using the DMA buffer size (dma_bytes) instead, the complete DMA buffer
can be mmapp'ed and the issue is fixed.
This issue was detected on an ARM platform (TI AM57xx) using the RME
HDSP MADI PCIe soundcard.
Fixes: 657b1989dacf ("ALSA: pcm - Use dma_mmap_coherent() if available") Signed-off-by: Stefan Roese <sr@denx.de> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:
Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.
Fixes: 5c9c11e1c47c ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0") Cc: <stable@vger.kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
