Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration") Cc: <stable@vger.kernel.org> # 5.15.x Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading from the CMOS involves writing to the index register and then
reading from the data register. Therefore access to the CMOS has to be
serialized with rtc_lock. This invocation of CMOS_READ was not
serialized, which could cause trouble when other code is accessing CMOS
at the same time.
Use spin_lock_irq() like the rest of the function.
Nothing in kernel modifies the RTC_DM_BINARY bit, so there could be a
separate pair of spin_lock_irq() / spin_unlock_irq() before doing the
math.
Ammar Faizi reported that our exit code handling is wrong. We truncate
it to the lowest 8 bits but the syscall itself is expected to take a
regular 32-bit signed integer, not an unsigned char. It's the kernel
that later truncates it to the lowest 8 bits. The difference is visible
in strace, where the program below used to show exit(255) instead of
exit(-1):
int main(void)
{
return -1;
}
This patch applies the fix to all archs. x86_64, i386, arm64, armv7 and
mips were all tested and confirmed to work fine now. Risc-v was not
tested but the change is trivial and exactly the same as for other archs.
Reported-by: Ammar Faizi <ammar.faizi@students.amikom.ac.id> Cc: stable@vger.kernel.org Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After re-checking in the spec and comparing stack offsets with glibc,
The last pushed argument must be 16-byte aligned (i.e. aligned before the
call) so that in the callee esp+4 is multiple of 16, so the principle is
the 32-bit equivalent to what Ammar fixed for x86_64. It's possible that
32-bit code using SSE2 or MMX could have been affected. In addition the
frame pointer ought to be zero at the deepest level.
x86 AES-NI routines can deal with unaligned data. Crypto context
(key, iv etc.) have to be aligned but we take care of that separately
by copying it onto the stack. We were feeding unaligned data into
crypto routines up until commit 83c83e658863 ("crypto: aesni -
refactor scatterlist processing") switched to use the full
skcipher API which uses cra_alignmask to decide data alignment.
This fixes 21% performance regression in kTLS.
Tested by booting with CONFIG_CRYPTO_MANAGER_EXTRA_TESTS=y
(and running thru various kTLS packets).
Before this patch, the `_start` function looks like this:
``` 0000000000001170 <_start>:
1170: pop %rdi
1171: mov %rsp,%rsi
1174: lea 0x8(%rsi,%rdi,8),%rdx
1179: and $0xfffffffffffffff0,%rsp
117d: sub $0x8,%rsp
1181: call 1000 <main>
1186: movzbq %al,%rdi
118a: mov $0x3c,%rax
1191: syscall
1193: hlt
1194: data16 cs nopw 0x0(%rax,%rax,1)
119f: nop
```
Note the "and" to %rsp with $-16, it makes the %rsp be 16-byte aligned,
but then there is a "sub" with $0x8 which makes the %rsp no longer
16-byte aligned, then it calls main. That's the bug!
What actually the x86-64 System V ABI mandates is that right before the
"call", the %rsp must be 16-byte aligned, not after the "call". So the
"sub" with $0x8 here breaks the alignment. Remove it.
An example where this rule matters is when the callee needs to align
its stack at 16-byte for aligned move instruction, like `movdqa` and
`movaps`. If the callee can't align its stack properly, it will result
in segmentation fault.
x86-64 System V ABI also mandates the deepest stack frame should be
zero. Just to be safe, let's zero the %rbp on startup as the content
of %rbp may be unspecified when the program starts. Now it looks like
this:
``` 0000000000001170 <_start>:
1170: pop %rdi
1171: mov %rsp,%rsi
1174: lea 0x8(%rsi,%rdi,8),%rdx
1179: xor %ebp,%ebp # zero the %rbp
117b: and $0xfffffffffffffff0,%rsp # align the %rsp
117f: call 1000 <main>
1184: movzbq %al,%rdi
1188: mov $0x3c,%rax
118f: syscall
1191: hlt
1192: data16 cs nopw 0x0(%rax,%rax,1)
119d: nopl (%rax)
```
Cc: Bedirhan KURT <windowz414@gnuweeb.org> Cc: Louvian Lyndal <louvianlyndal@gmail.com> Reported-by: Peter Cordes <peter@cordes.ca> Signed-off-by: Ammar Faizi <ammar.faizi@students.amikom.ac.id>
[wt: I did this on purpose due to a misunderstanding of the spec, other
archs will thus have to be rechecked, particularly i386] Cc: stable@vger.kernel.org Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Stolen memory" is memory set aside for use by an Intel integrated GPU.
The intel_graphics_quirks() early quirk reserves this memory when it is
called for a GPU that appears in the intel_early_ids[] table of integrated
GPUs.
Previously intel_graphics_quirks() was marked as QFLAG_APPLY_ONCE, so it
was called only for the first Intel GPU found. If a discrete GPU happened
to be enumerated first, intel_graphics_quirks() was called for it but not
for any integrated GPU found later. Therefore, stolen memory for such an
integrated GPU was never reserved.
For example, this problem occurs in this Alderlake-P (integrated) + DG2
(discrete) topology where the DG2 is found first, but stolen memory is
associated with the integrated GPU:
Remove the QFLAG_APPLY_ONCE flag and call intel_graphics_quirks() for every
Intel GPU. Reserve stolen memory for the first GPU that appears in
intel_early_ids[].
[bhelgaas: commit log, add code comment, squash in
https://lore.kernel.org/r/20220118190558.2ququ4vdfjuahicm@ldmartin-desk2] Link: https://lore.kernel.org/r/20220114002843.2083382-1-lucas.demarchi@intel.com Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
raw_smp_processor_id() doesn't return the hart id as stated in
arch/riscv/include/asm/smp.h, use smp_processor_id() instead
to get the cpu id, and cpuid_to_hartid_map() to pass the hart id
to the next kernel. This fixes kexec on HiFive Unleashed/Unmatched
where cpu ids and hart ids don't match (on qemu-virt they match).
On kdump instead of using an intermediate step to relocate the kernel,
that lives in a "control buffer" outside the current kernel's mapping,
we jump to the crash kernel directly by calling riscv_kexec_norelocate().
The current implementation uses va_pa_offset while switching to physical
addressing, however since we moved the kernel outside the linear mapping
this won't work anymore since riscv_kexec_norelocate() is part of the
kernel mapping and we should use kernel_map.va_kernel_pa_offset, and also
take XIP kernel into account.
We don't really need to use va_pa_offset on riscv_kexec_norelocate, we
can just set STVEC to the physical address of the new kernel instead and
let the hart jump to the new kernel on the next instruction after setting
SATP to zero. This fixes kdump and is also simpler/cleaner.
I tested this on the latest qemu and HiFive Unmatched and works as
expected.
Fixes: 2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear mapping") Signed-off-by: Nick Kossifidis <mick@ics.forth.gr> Reviewed-by: Alexandre Ghiti <alex@ghiti.fr> Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating crash kernel region without explicitly specifying its
base address/size, memblock_phys_alloc_range will attempt to allocate
memory top to bottom (memblock.bottom_up is false), so the crash
kernel region will end up in highmem on 64bit systems. This way
swiotlb can't work on the crash kernel, since there won't be any
32bit addressible memory available for the bounce buffers.
Try to allocate 32bit addressible memory if available, for the
crash kernel by restricting the top search address to be less
than SZ_4G. If that fails fallback to the previous behavior.
I tested this on HiFive Unmatched where the pci-e controller needs
swiotlb to work, with this patch it's possible to access the pci-e
controller on crash kernel and mount the rootfs from the nvme.
Use what is currently the SMP=y version of riscv_cpuid_to_hartid_mask()
for both SMP=y and SMP=n to fix a build failure with KVM=m and SMP=n due
to boot_cpu_hartid not being exported. This also fixes a second bug
where the SMP=n version assumes the sole CPU in the system is in the
incoming mask, which may not hold true in kvm_riscv_vcpu_sbi_ecall() if
the KVM guest VM has multiple vCPUs (on a SMP=n system).
Fixes: 1ef46c231df4 ("RISC-V: Implement new SBI v0.2 extensions") Reported-by: Adam Borowski <kilobyte@angband.pl> Reviewed-by: Anup Patel <anup.patel@wdc.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_MAXPHYSMEM_* are actually never used, even the nommu defconfigs
selecting the MAXPHYSMEM_2GB had no effects on PAGE_OFFSET since it was
preempted by !MMU case right before.
In addition, the move of the kernel mapping at the end of the address
space broke the use of MAXPHYSMEM_2G with MMU since it defines PAGE_OFFSET
at the same address as the kernel mapping.
The ECC engine on the JZ4740 SoC requires the ECC data to be read before
the page; using the default page reading function does not work. Indeed,
the old JZ4740 NAND driver (removed in 5.4) did use the 'OOB first' flag
that existed back then.
Use the newly created nand_read_page_hwecc_oob_first() to address this
issue.
This issue was not found when the new ingenic-nand driver was developed,
most likely because the Device Tree used had the nand-ecc-mode set to
"hw_oob_first", which seems to not be supported anymore.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-5-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2 Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not the child partition should be removed from the partition list
but the partition itself. Otherwise the partition list gets broken
and any subsequent remove operations leads to a kernel panic.
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de> Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Signed-off-by: Christian Eggers <ceggers@arri.de> Cc: stable@vger.kernel.org Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot detected a NULL pointer dereference of nfc_llcp_sock->dev pointer
(which is a 'struct nfc_dev *') with calls to llcp_sock_sendmsg() after
a failed llcp_sock_bind(). The message being sent is a SOCK_DGRAM.
KASAN report:
BUG: KASAN: null-ptr-deref in nfc_alloc_send_skb+0x2d/0xc0
Read of size 4 at addr 00000000000005c8 by task llcp_sock_nfc_a/899
The issue was visible only with multiple simultaneous calls to bind() and
sendmsg(), which resulted in most of the bind() calls to fail. The
bind() was failing on checking if there is available WKS/SDP/SAP
(respective bit in 'struct nfc_llcp_local' fields). When there was no
available WKS/SDP/SAP, the bind returned error but the sendmsg() to such
socket was able to trigger mentioned NULL pointer dereference of
nfc_llcp_sock->dev.
The code looks simply racy and currently it protects several paths
against race with checks for (!nfc_llcp_sock->local) which is NULL-ified
in error paths of bind(). The llcp_sock_sendmsg() did not have such
check but called function nfc_llcp_send_ui_frame() had, although not
protected with lock_sock().
Therefore the race could look like (same socket is used all the time):
CPU0 CPU1
==== ====
llcp_sock_bind()
- lock_sock()
- success
- release_sock()
- return 0
llcp_sock_sendmsg()
- lock_sock()
- release_sock()
llcp_sock_bind(), same socket
- lock_sock()
- error
- nfc_llcp_send_ui_frame()
- if (!llcp_sock->local)
- llcp_sock->local = NULL
- nfc_put_device(dev)
- dereference llcp_sock->dev
- release_sock()
- return -ERRNO
The nfc_llcp_send_ui_frame() checked llcp_sock->local outside of the
lock, which is racy and ineffective check. Instead, its caller
llcp_sock_sendmsg(), should perform the check inside lock_sock().
Reported-and-tested-by: syzbot+7f23bcddf626e0593a39@syzkaller.appspotmail.com Fixes: b874dec21d1c ("NFC: Implement LLCP connection less Tx path") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fuzzed image, SSA table may indicate that a data block belongs to
invalid node, which node ID is out-of-range (0, 1, 2 or max_nid), in
order to avoid migrating inconsistent data in such corrupted image,
let's do sanity check anyway before data block migration.
F2FS-fs (loop0): sanity_check_inode: inode (ino=49) extent info [5942, 4294180864, 4] is incorrect, run fsck to fix
F2FS-fs (loop0): f2fs_check_nid_range: out-of-range nid=31340049, run fsck to fix.
BUG: kernel NULL pointer dereference, address: 0000000000000000
folio_mark_dirty+0x33/0x50
move_data_page+0x2dd/0x460 [f2fs]
do_garbage_collect+0xc18/0x16a0 [f2fs]
f2fs_gc+0x1d3/0xd90 [f2fs]
f2fs_balance_fs+0x13a/0x570 [f2fs]
f2fs_create+0x285/0x840 [f2fs]
path_openat+0xe6d/0x1040
do_filp_open+0xc5/0x140
do_sys_openat2+0x23a/0x310
do_sys_open+0x57/0x80
The root cause is for special file: e.g. character, block, fifo or socket file,
f2fs doesn't assign address space operations pointer array for mapping->a_ops field,
so, in a fuzzed image, SSA table indicates a data block belong to special file, when
f2fs tries to migrate that block, it causes NULL pointer access once move_data_page()
calls a_ops->set_dirty_page().
Cc: stable@vger.kernel.org Reported-by: Wenqing Liu <wenqingliu0120@gmail.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some weird devices set the codec SSID vendor ID 0, and
snd_pci_quirk_lookup_id() loop aborts at the point although it should
still try matching with the SSID device ID. This resulted in a
missing quirk for some old Macs.
Fix the loop termination condition to check both subvendor and
subdevice.
If we ever see a touch report with contact count data we initialize
several variables used to read the contact count in the pre-report
phase. These variables are never reset if we process a report which
doesn't contain a contact count, however. This can cause the pre-
report function to trigger a read of arbitrary memory (e.g. NULL
if we're lucky) and potentially crash the driver.
This commit restores resetting of the variables back to default
"none" values that were used prior to the commit mentioned
below.
AES hardware may internally re-classify a contact that it thought was
intentional as a palm. Intentional contacts are reported as "down" with
the confidence bit set. When this re-classification occurs, however, the
state transitions to "up" with the confidence bit cleared. This kind of
transition appears to be legal according to Microsoft docs, but we do
not handle it correctly. Because the confidence bit is clear, we don't
call `wacom_wac_finger_slot` and update userspace. This causes hung
touches that confuse userspace and interfere with pen arbitration.
This commit adds a special case to ignore the confidence flag if a contact
is reported as removed. This ensures we do not leave a hung touch if one
of these re-classification events occured. Ideally we'd have some way to
also let userspace know that the touch has been re-classified as a palm
and needs to be canceled, but that's not possible right now :)
Link: https://github.com/linuxwacom/input-wacom/issues/288 Fixes: 7fb0413baa7f (HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts) CC: stable@vger.kernel.org Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Reviewed-by: Ping Cheng <ping.cheng@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two values go hand-in-hand and must be valid for the driver to
behave correctly. We are currently lazy about updating the values and
rely on the "expected" code flow to take care of making sure they're
valid at the point they're needed. The "expected" flow changed somewhat
with commit f8b6a74719b5 ("HID: wacom: generic: Support multiple tools
per report"), however. This led to problems with the DTH-2452 due (in
part) to *all* contacts being fully processed -- even those past the
expected contact count. Specifically, the received count gets reset to
0 once all expected fingers are processed, but not the expected count.
The rest of the contacts in the report are then *also* processed since
now the driver thinks we've only processed 0 of N expected contacts.
Later commits such as 7fb0413baa7f (HID: wacom: Use "Confidence" flag to
prevent reporting invalid contacts) worked around the DTH-2452 issue by
skipping the invalid contacts at the end of the report, but this is not
a complete fix. The confidence flag cannot be relied on when a contact
is removed (see the following patch), and dealing with that condition
re-introduces the DTH-2452 issue unless we also address this contact
count laziness. By resetting expected and received counts at the same
time we ensure the driver understands that there are 0 more contacts
expected in the report. Similarly, we also make sure to reset the
received count if for some reason we're out of sync in the pre-report
phase.
Link: https://github.com/linuxwacom/input-wacom/issues/288 Fixes: f8b6a74719b5 ("HID: wacom: generic: Support multiple tools per report") CC: stable@vger.kernel.org Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Reviewed-by: Ping Cheng <ping.cheng@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uhid has to run hid_add_device() from workqueue context while allowing
parallel use of the userspace API (which is protected with ->devlock).
But hid_add_device() can fail. Currently, that is handled by immediately
destroying the associated HID device, without using ->devlock - but if
there are concurrent requests from userspace, that's wrong and leads to
NULL dereferences and/or memory corruption (via use-after-free).
Fix it by leaving the HID device as-is in the worker. We can clean it up
later, either in the UHID_DESTROY command handler or in the ->release()
handler.
Battery status on Elan tablet driver is reported for the HP ENVY x360
15t-dr100. There is no separate battery for the Elan controller resulting in a
battery level report of 0% or 1% depending on whether a stylus has interacted
with the screen. These low battery level reports causes a variety of bad
behavior in desktop environments. This patch adds the appropriate quirk to
indicate that the batery status is unused for this target.
When the TDP MMU is write-protection GFNs for page table protection (as
opposed to for dirty logging, or due to the HVA not being writable), it
checks if the SPTE is already write-protected and if so skips modifying
the SPTE and the TLB flush.
This behavior is incorrect because it fails to check if the SPTE
is write-protected for page table protection, i.e. fails to check
that MMU-writable is '0'. If the SPTE was write-protected for dirty
logging but not page table protection, the SPTE could locklessly be made
writable, and vCPUs could still be running with writable mappings cached
in their TLB.
Fix this by only skipping setting the SPTE if the SPTE is already
write-protected *and* MMU-writable is already clear. Technically,
checking only MMU-writable would suffice; a SPTE cannot be writable
without MMU-writable being set. But check both to be paranoid and
because it arguably yields more readable code.
Fixes: 46044f72c382 ("kvm: x86/mmu: Support write protection for nesting in tdp MMU") Cc: stable@vger.kernel.org Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20220113233020.3986005-2-dmatlack@google.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Legion Y9000X 2020 has a speaker, but the speaker doesn't work.
This can be fixed by applying alc285_fixup_ideapad_s740_coef
to fix the speaker's coefficients.
Besides, to support the transition between the speaker and the headphone,
alc287_fixup_legion_15imhg05_speakers needs to be run.
HDA regression is recently reported on Tegra194 based platforms.
This happens because "hda2codec_2x" reset does not really exist
in Tegra194 and it causes probe failure. All the HDA based audio
tests fail at the moment. This underlying issue is exposed by
commit c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP
response") which now checks return code of BPMP command response.
Fix this issue by skipping unavailable reset on Tegra194.
The speaker fixup that is used for the Yoga 7 14ITL5 also applies to
the IdeaPad Slim 9i 14ITL5. The attached patch applies the quirk to
initialise the amplifier on the IdeaPad Slim 9i as well.
This patch addresses an issue where after rebooting from Windows into Linux
there would be no audio output.
It turns out that the Realtek Audio driver on Windows changes some coeffs
which are not being reset/reinitialized when rebooting the machine. As a
result, there is no audio output until these coeffs are being reset to
their initial state. This patch takes care of that by setting known-good
(initial) values to the coeffs.
We initially relied upon alc1220_fixup_clevo_p950() to fix some pins in the
connection list. However, it also sets coef 0x7 which does not need to be
touched. Furthermore, to prevent mixing device-specific quirks I introduced
a new alc1220_fixup_gb_x570() which is heavily based on
alc1220_fixup_clevo_p950() but does not set coeff 0x7 and fixes the coeffs
that are actually needed instead.
This new alc1220_fixup_gb_x570() is believed to also work for other boards,
like the Gigabyte X570 Aorus Extreme and the newer Gigabyte Aorus X570S
Master. However, as there is no way for me to test these I initially only
enable this new behaviour for the mainboard I have which is the Gigabyte
X570(non-S) Aorus Master.
I tested this patch on the 5.15 branch as well as on master and it is
working well for me.
This patch adds another possible subsystem ID for the ALC287 used by
the Lenovo Yoga 15ITL5.
It uses the same initalization as the others.
This patch has been tested and works for my device.
The fixed counter 3 is used for the Topdown metrics, which hasn't been
enabled for KVM guests. Userspace accessing to it will fail as it's not
included in get_fixed_pmc(). This breaks KVM selftests on ICX+ machines,
which have this counter.
To reproduce it on ICX+ machines, ./state_test reports:
==== Test Assertion Failure ====
lib/x86_64/processor.c:1078: r == nmsrs
pid=4564 tid=4564 - Argument list too long
1 0x000000000040b1b9: vcpu_save_state at processor.c:1077
2 0x0000000000402478: main at state_test.c:209 (discriminator 6)
3 0x00007fbe21ed5f92: ?? ??:0
4 0x000000000040264d: _start at ??:?
Unexpected result from KVM_GET_MSRS, r: 17 (failed MSR was 0x30c)
With this patch, it works well.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Message-Id: <20211217124934.32893-1-wei.w.wang@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Fixes: e2ada66ec418 ("kvm: x86: Add Intel PMU MSRs to msrs_to_save[]") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 'perf report', entering a recursive function from inside of itself
(either directly of indirectly through some other function) results in
calling symbol__annotate2 multiple() times, and freeing the whole
disassembly when exiting from the innermost instance.
The first issue causes the function's disassembly to be duplicated, and
the latter a heap use-after-free (and crash) when trying to access the
disassembly again.
I reproduced the bug on perf 5.11.22 (Ubuntu 20.04.3 LTS) and 5.16.rc8
with the following testcase (compile with gcc recursive.c -o recursive).
To reproduce:
- perf record ./recursive
- perf report
- enter fibonacci and annotate it
- move the cursor on one of the "callq fibonacci" instructions and press enter
- at this point there will be two copies of the function in the disassembly
- go back by pressing q, and perf will crash
This patch addresses the issue by annotating a function and freeing the
associated memory on exit only if no annotation is already present, so
that a recursive function is only annotated on entry.
Signed-off-by: Dario Petrillo <dario.pk1@gmail.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@kernel.org Link: http://lore.kernel.org/lkml/20220109234441.325106-1-dario.pk1@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An initialised kobject must be freed using kobject_put() to avoid
leaking associated resources (e.g. the object name).
Commit fe3c60684377 ("firmware: Fix a reference count leak.") "fixed"
the leak in the first error path of the file registration helper but
left the second one unchanged. This "fix" would however result in a NULL
pointer dereference due to the release function also removing the never
added entry from the fw_cfg_entry_cache list. This has now been
addressed.
Fix the remaining kobject leak by restoring the common error path and
adding the missing kobject_put().
Commit fe3c60684377 ("firmware: Fix a reference count leak.") "fixed"
a kobject leak in the file registration helper by properly calling
kobject_put() for the entry in case registration of the object fails
(e.g. due to a name collision).
This would however result in a NULL pointer dereference when the
release function tries to remove the never added entry from the
fw_cfg_entry_cache list.
Fix this by moving the list-removal out of the release function.
Note that the offending commit was one of the benign looking umn.edu
fixes which was reviewed but not reverted. [1][2]
Make sure to always NUL-terminate file names retrieved from the firmware
to avoid accessing data beyond the entry slab buffer and exposing it
through sysfs in case the firmware data is corrupt.
Fixes: 75f3e8e47f38 ("firmware: introduce sysfs driver for QEMU's fw_cfg device") Cc: stable@vger.kernel.org # 4.6 Cc: Gabriel Somlo <somlo@cmu.edu> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211201132528.30025-4-johan@kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[200~raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 1 PID: 1206 at kernel/locking/irqflag-debug.c:10
warn_bogus_irq_restore+0x1d/0x20 kernel/locking/irqflag-debug.c:10
Hardware initialization for the rtl8188cu can run for as long as 350 ms,
and the routine may be called with interrupts disabled. To avoid locking
the machine for this long, the current routine saves the interrupt flags
and enables local interrupts. The problem is that it restores the flags
at the end without disabling local interrupts first.
This patch fixes commit a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long
disable of IRQs").
Reported-by: syzbot+cce1ee31614c171f5595@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Fixes: a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long disable of IRQs") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211215171105.20623-1-Larry.Finger@lwfinger.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing bulk-endpoint max-packet sanity check to
uvc_video_start_transfer() to avoid division by zero in
uvc_alloc_urb_buffers() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: c0efd232929c ("V4L/DVB (8145a): USB Video Class driver") Cc: stable@vger.kernel.org # 2.6.26 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vga16fb framebuffer driver only supports Enhanced Graphics Adapter
(EGA) and Video Graphics Array (VGA) 16 color graphic cards.
But it doesn't check if the adapter is one of those or if a VGA16 mode
is used. This means that the driver will be probed even if a VESA BIOS
Extensions (VBE) or Graphics Output Protocol (GOP) interface is used.
This issue has been present for a long time but it was only exposed by
commit d391c5827107 ("drivers/firmware: move x86 Generic System
Framebuffers support") since the platform device registration to match
the {vesa,efi}fb drivers is done later as a consequence of that change.
All non-x86 architectures though treat orig_video_isVGA as a boolean so
only do the supported video mode check for x86 and not for other arches.
The 9P2000.L setattr method v9fs_vfs_setattr_dotl() copies struct iattr
values without checking whether they are valid causing unitialized
values to be copied. The 9P2000 setattr method v9fs_vfs_setattr() method
gets this right. Check whether struct iattr fields are valid first
before copying in v9fs_vfs_setattr_dotl() too and make sure that all
other fields are set to 0 apart from {g,u}id which should be set to
INVALID_{G,U}ID. This ensure that they can be safely sent over the wire
or printed for debugging later on.
Link: https://lkml.kernel.org/r/20211129114434.3637938-1-brauner@kernel.org Link: https://lkml.kernel.org/r/000000000000a0d53f05d1c72a4c%40google.com Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Latchesar Ionkov <lucho@ionkov.net> Cc: Dominique Martinet <asmadeus@codewreck.org> Cc: stable@kernel.org Cc: v9fs-developer@lists.sourceforge.net Reported-by: syzbot+dfac92a50024b54acaa4@syzkaller.appspotmail.com Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
[Dominique: do not set a/mtime with just ATTR_A/MTIME as discussed] Signed-off-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With KVM_CAP_S390_USER_SIGP, there are only five Signal Processor
orders (CONDITIONAL EMERGENCY SIGNAL, EMERGENCY SIGNAL, EXTERNAL CALL,
SENSE, and SENSE RUNNING STATUS) which are intended for frequent use
and thus are processed in-kernel. The remainder are sent to userspace
with the KVM_CAP_S390_USER_SIGP capability. Of those, three orders
(RESTART, STOP, and STOP AND STORE STATUS) have the potential to
inject work back into the kernel, and thus are asynchronous.
Let's look for those pending IRQs when processing one of the in-kernel
SIGP orders, and return BUSY (CC2) if one is in process. This is in
agreement with the Principles of Operation, which states that only one
order can be "active" on a CPU at a time.
Cc: stable@vger.kernel.org Suggested-by: David Hildenbrand <david@redhat.com> Signed-off-by: Eric Farman <farman@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com> Acked-by: David Hildenbrand <david@redhat.com> Link: https://lore.kernel.org/r/20211213210550.856213-2-farman@linux.ibm.com
[borntraeger@linux.ibm.com: add stable tag] Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Override the Processor Trace (PT) interrupt handler for guest mode if and
only if PT is configured for host+guest mode, i.e. is being used
independently by both host and guest. If PT is configured for system
mode, the host fully controls PT and must handle all events.
Fixes: 8479e04e7d6b ("KVM: x86: Inject PMI for KVM guest") Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Reported-by: Artem Kashkanov <artem.kashkanov@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211111020738.2512932-4-seanjc@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wait to register perf callbacks until after doing vendor hardaware setup.
VMX's hardware_setup() configures Intel Processor Trace (PT) mode, and a
future fix to register the Intel PT guest interrupt hook if and only if
Intel PT is exposed to the guest will consume the configured PT mode.
Delaying registration to hardware setup is effectively a nop as KVM's perf
hooks all pivot on the per-CPU current_vcpu, which is non-NULL only when
KVM is handling an IRQ/NMI in a VM-Exit path. I.e. current_vcpu will be
NULL throughout both kvm_arch_init() and kvm_arch_hardware_setup().
Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211111020738.2512932-3-seanjc@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Protect perf_guest_cbs with RCU to fix multiple possible errors. Luckily,
all paths that read perf_guest_cbs already require RCU protection, e.g. to
protect the callback chains, so only the direct perf_guest_cbs touchpoints
need to be modified.
Bug #1 is a simple lack of WRITE_ONCE/READ_ONCE behavior to ensure
perf_guest_cbs isn't reloaded between a !NULL check and a dereference.
Fixed via the READ_ONCE() in rcu_dereference().
Bug #2 is that on weakly-ordered architectures, updates to the callbacks
themselves are not guaranteed to be visible before the pointer is made
visible to readers. Fixed by the smp_store_release() in
rcu_assign_pointer() when the new pointer is non-NULL.
Bug #3 is that, because the callbacks are global, it's possible for
readers to run in parallel with an unregisters, and thus a module
implementing the callbacks can be unloaded while readers are in flight,
resulting in a use-after-free. Fixed by a synchronize_rcu() call when
unregistering callbacks.
Bug #1 escaped notice because it's extremely unlikely a compiler will
reload perf_guest_cbs in this sequence. perf_guest_cbs does get reloaded
for future derefs, e.g. for ->is_user_mode(), but the ->is_in_guest()
guard all but guarantees the consumer will win the race, e.g. to nullify
perf_guest_cbs, KVM has to completely exit the guest and teardown down
all VMs before KVM start its module unload / unregister sequence. This
also makes it all but impossible to encounter bug #3.
Bug #2 has not been a problem because all architectures that register
callbacks are strongly ordered and/or have a static set of callbacks.
But with help, unloading kvm_intel can trigger bug #1 e.g. wrapping
perf_guest_cbs with READ_ONCE in perf_misc_flags() while spamming
kvm_intel module load/unload leads to:
The "PAGE_SIZE - 2 - size" calculation in legacy_parse_param() is an
unsigned type so a large value of "size" results in a high positive
value instead of a negative value as expected. Fix this by getting rid
of the subtraction.
Signed-off-by: Jamie Hill-Daniel <jamie@hill-daniel.co.uk> Signed-off-by: William Liu <willsroot@protonmail.com> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Tested-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the string passed into qcom_pil_info_store() isn't as long as
PIL_RELOC_NAME_LEN we'll try to copy the string assuming the length is
PIL_RELOC_NAME_LEN to the io space and go beyond the bounds of the
string. Let's only copy as many byes as the string is long, ignoring the
NUL terminator.
This fixes the following KASAN error:
BUG: KASAN: global-out-of-bounds in __memcpy_toio+0x124/0x140
Read of size 1 at addr ffffffd35086e386 by task rmtfs/2392
'buffer_index_array' really looks like a bitmap. So it should be allocated
as such.
When kzalloc is called, a number of bytes is expected, but a number of
longs is passed instead.
In get(), if not enough memory is allocated, un-allocated memory may be
read or written.
So use bitmap_zalloc() to safely allocate the correct memory size and
avoid un-expected behavior.
While at it, change the corresponding kfree() into bitmap_free() to keep
the semantic.
When UBSAN is enabled a case is shown on unplugging the display that
this variable hasn't been initialized by `update_dsc_caps`, presumably
when the display was unplugged it wasn't copied from the DPCD.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1956497 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to Linux v5.4 devtmpfs used mount_single() which treats the given
mount options as "remount" options, so it updates the configuration of
the single super_block on each mount.
Since that was changed, the mount options used for devtmpfs are ignored.
This is a regression which affect systemd - which mounts devtmpfs with
"-o mode=755,size=4m,nr_inodes=1m".
This patch restores the "remount" effect by calling reconfigure_single()
Fixes: d401727ea0d7 ("devtmpfs: don't mix {ramfs,shmem}_fill_super() with mount_single()") Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang warns about excessive stack usage in this driver when
UBSAN is enabled:
drivers/staging/greybus/audio_topology.c:977:12: error: stack frame size of 1836 bytes in function 'gbaudio_tplg_create_widget' [-Werror,-Wframe-larger-than=]
Rework this code to no longer use compound literals for
initializing the structure in each case, but instead keep
the common bits in a preallocated constant array and copy
them as needed.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean types:
drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This construct is intentional, as it allows every one of the calls to
ilk_increase_wm_latency() to occur (instead of short circuiting with
logical OR) while still caring about the result of each call.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each ilk_increase_wm_latency() call to changed, which
keeps the meaning of the code the same but makes it obvious that every
one of these calls is expected to happen.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean expressions:
In file included from drivers/staging/wlan-ng/prism2usb.c:2:
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning
1 warning generated.
The comment explains that short circuiting here is undesirable, as the
calls to test_and_{clear,set}_bit() need to happen for both sides of the
expression.
Clang's suggestion would work to silence the warning but the readability
of the expression would suffer even more. To clean up the warning and
make the block more readable, use a variable for each side of the
bitwise expression.
A lot of userspace depends on a descriptive name for vdev. Without this
patch, users have a hard time figuring out which camera shall they use
for their video conferencing.
Currently, if CONFIG_RANDOM_TRUST_BOOTLOADER is enabled, multiple calls
to add_bootloader_randomness() are broken and can cause a NULL pointer
dereference, as noted by Ivan T. Ivanov. This is not only a hypothetical
problem, as qemu on arm64 may provide bootloader entropy via EFI and via
devicetree.
On the first call to add_hwgenerator_randomness(), crng_fast_load() is
executed, and if the seed is long enough, crng_init will be set to 1.
On subsequent calls to add_bootloader_randomness() and then to
add_hwgenerator_randomness(), crng_fast_load() will be skipped. Instead,
wait_event_interruptible() and then credit_entropy_bits() will be called.
If the entropy count for that second seed is large enough, that proceeds
to crng_reseed().
However, both wait_event_interruptible() and crng_reseed() depends
(at least in numa_crng_init()) on workqueues. Therefore, test whether
system_wq is already initialized, which is a sufficient indicator that
workqueue_init_early() has progressed far enough.
If we wind up hitting the !system_wq case, we later want to do what
would have been done there when wqs are up, so set a flag, and do that
work later from the rand_initialize() call.
Reported-by: Ivan T. Ivanov <iivanov@suse.de> Fixes: 18b915ac6b0a ("efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness") Cc: stable@vger.kernel.org Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
[Jason: added crng_need_done state and related logic.] Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_extract_crng() does plain loads of crng->init_time and
crng_global_init_time, which causes undefined behavior if
crng_reseed() and RNDRESEEDCRNG modify these corrently.
Use READ_ONCE() and WRITE_ONCE() to make the behavior defined.
Don't fix the race on crng->init_time by protecting it with crng->lock,
since it's not a problem for duplicate reseedings to occur. I.e., the
lockless access with READ_ONCE() is fine.
Fixes: d848e5f8e1eb ("random: add new ioctl RNDRESEEDCRNG") Fixes: e192be9d9a30 ("random: replace non-blocking pool with a Chacha20-based CRNG") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
extract_crng() and crng_backtrack_protect() load crng_node_pool with a
plain load, which causes undefined behavior if do_numa_crng_init()
modifies it concurrently.
Fix this by using READ_ONCE(). Note: as per the previous discussion
https://lore.kernel.org/lkml/20211219025139.31085-1-ebiggers@kernel.org/T/#u,
READ_ONCE() is believed to be sufficient here, and it was requested that
it be used here instead of smp_load_acquire().
Also change do_numa_crng_init() to set crng_node_pool using
cmpxchg_release() instead of mb() + cmpxchg(), as the former is
sufficient here but is more lightweight.
Fixes: 1e7f583af67b ("random: make /dev/urandom scalable for silly userspace programs") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
In isotp_rcv_ff() 32 bit of data received over the network is assigned
to struct tpcon::len. Later in that function the length is checked for
the maximal supported length against MAX_MSG_LENGTH.
As struct tpcon::len is an "int" this check does not work, if the
provided length overflows the "int".
Later on struct tpcon::idx is compared against struct tpcon::len.
To fix this problem this patch converts both struct tpcon::{idx,len}
to unsigned int.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/20220105132429.1170627-1-mkl@pengutronix.de Cc: stable@vger.kernel.org Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The runtime PM callback may be called as soon as the runtime PM facility
is enabled and activated. It means that ->suspend() may be called before
we finish probing the device in the ACPI case. Hence, NULL pointer
dereference:
intel-lpss INT34BA:00: IRQ index 0 not found
BUG: kernel NULL pointer dereference, address: 0000000000000030
...
Workqueue: pm pm_runtime_work
RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]
To fix this, first try to register the device and only after that enable
runtime PM facility.
Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices") Reported-by: Orlando Chamberlain <redecorating@protonmail.com> Reported-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent reported that they have seen a significant amount of TCP retransmissions
at high throughput from applications residing in network namespaces talking to
the outside world via veths. The drops were seen on the qdisc layer (fq_codel,
as per systemd default) of the phys device such as ena or virtio_net due to all
traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the
setup was _not_ using XDP on veths as the issue is generic.)
More specifically, after edbea9220251 ("veth: Store queue_mapping independently
of XDP prog presence") which made it all the way back to v4.19.184+,
skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX
queue by default for veths) instead of leaving at 0.
This is eventually retained and callbacks like ena_select_queue() will also pick
single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic
is forwarded to that device via upper stack or other means. Similarly, for others
not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might
call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.
In general, it is a _bad_ idea for virtual devices like veth to mess around with
queue selection [by default]. Given dev->real_num_tx_queues is by default 1,
the skb->queue_mapping was left untouched, and so prior to edbea9220251 the
netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.
Unbreak this and restore prior behavior by removing the skb_record_rx_queue()
from veth_xmit() altogether.
If the veth peer has an XDP program attached, then it would return the first RX
queue index in xdp_md->rx_queue_index (unless configured in non-default manner).
However, this is still better than breaking the generic case.
Fixes: edbea9220251 ("veth: Store queue_mapping independently of XDP prog presence") Fixes: 638264dc9022 ("veth: Support per queue XDP ring") Reported-by: Laurent Bernaille <laurent.bernaille@datadoghq.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Cc: Toshiaki Makita <toshiaki.makita1@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have a bug causing them to not work if they query
LE tx power on startup. Thus we add a quirk in order to not query it
and default min/max tx power values to HCI_TX_POWER_INVALID.
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller. But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports. When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data. This was
discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer. If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <stable@vger.kernel.org> Tested-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset GPIO was marked active-high, which is against what's specified
in the documentation. Mark the reset GPIO as active-low. With this
change, Bluetooth can now be used on the i9100.
Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2") Cc: stable@vger.kernel.org Signed-off-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20211031234137.87070-1-paul@crapouillou.net Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing bulk-out endpoint sanity check to probe() to avoid
division by zero in bfusb_send_frame() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
This patch fixes the broken LED quirk for Intel legacy ROM devices.
To fix the LED issue that doesn't turn off immediately, the host sends
the SW RFKILL command while shutting down the interface and it puts the
devices in SW RFKILL state.
Once the device is in SW RFKILL state, it can only accept HCI_Reset to
exit from the SW RFKILL state. This patch checks the quirk for broken
LED and sends the HCI_Reset before sending the HCI_Intel_Read_Version
command.
The affected legacy ROM devices are
- 8087:07dc
- 8087:0a2a
- 8087:0aa7
Fixes: ffcba827c0a1d ("Bluetooth: btintel: Fix the LED is not turning off immediately") Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 054aa8d439b9 ("fget: check that the fd still exists after getting
a ref to it") fixed a race with getting a reference to a file just as it
was being closed. It was a fairly minimal patch, and I didn't think
re-checking the file pointer lookup would be a measurable overhead,
since it was all right there and cached.
But I was wrong, as pointed out by the kernel test robot.
The 'poll2' case of the will-it-scale.per_thread_ops benchmark regressed
quite noticeably. Admittedly it seems to be a very artificial test:
doing "poll()" system calls on regular files in a very tight loop in
multiple threads.
That means that basically all the time is spent just looking up file
descriptors without ever doing anything useful with them (not that doing
'poll()' on a regular file is useful to begin with). And as a result it
shows the extra "re-check fd" cost as a sore thumb.
Happily, the regression is fixable by just writing the code to loook up
the fd to be better and clearer. There's still a cost to verify the
file pointer, but now it's basically in the noise even for that
benchmark that does nothing else - and the code is more understandable
and has better comments too.
[ Side note: this patch is also a classic case of one that looks very
messy with the default greedy Myers diff - it's much more legible with
either the patience of histogram diff algorithm ]
While auditing some other code, I noticed missing checks inside the pointer
arithmetic simulation, more specifically, adjust_ptr_min_max_vals(). Several
*_OR_NULL types are not rejected whereas they are _required_ to be rejected
given the expectation is that they get promoted into a 'real' pointer type
for the success case, that is, after an explicit != NULL check.
One case which stands out and is accessible from unprivileged (iff enabled
given disabled by default) is BPF ring buffer. From crafting a PoC, the NULL
check can be bypassed through an offset, and its id marking will then lead
to promotion of mem_or_null to a mem type.
bpf_ringbuf_reserve() helper can trigger this case through passing of reserved
flags, for example.
from 8 to 13: safe
processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 0
OK
All three commits, that is b121b341e598 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support"), 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it"), and the afbf21dce668 ("bpf: Support readonly/readwrite buffers in verifier") suffer the same
cause and their *_OR_NULL type pendants must be rejected in adjust_ptr_min_max_vals().
Make the test more robust by reusing reg_type_may_be_null() helper such that we catch
all *_OR_NULL types we have today and in future.
Note that pointer arithmetic on PTR_TO_BTF_ID, PTR_TO_RDONLY_BUF, and PTR_TO_RDWR_BUF
is generally allowed.
Fixes: b121b341e598 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support") Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it") Fixes: afbf21dce668 ("bpf: Support readonly/readwrite buffers in verifier") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
