The JFS filesystem calculates allocation group (AG) size using 1 <<
l2agsize in dbExtendFS(). When l2agsize exceeds 31 (possible with >2TB
aggregates on 32-bit systems), this 32-bit shift operation causes undefined
behavior and improper AG sizing.
On 32-bit architectures:
- Left-shifting 1 by 32+ bits results in 0 due to integer overflow
- This creates invalid AG sizes (0 or garbage values) in
sbi->bmap->db_agsize
- Subsequent block allocations would reference invalid AG structures
- Could lead to:
- Filesystem corruption during extend operations
- Kernel crashes due to invalid memory accesses
- Security vulnerabilities via malformed on-disk structures
Fix by casting to s64 before shifting:
bmp->db_agsize = (s64)1 << l2agsize;
This ensures 64-bit arithmetic even on 32-bit architectures. The cast
matches the data type of db_agsize (s64) and follows similar patterns in
JFS block calculation code.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The expression "inactags << bmp->db_agl2size" in the function
dbFinalizeBmap() is computed using int operands. Although the
values (inactags and db_agl2size) are derived from filesystem
parameters and are usually small, there is a theoretical risk that
the shift could overflow a 32-bit int if extreme values occur.
According to the C standard, shifting a signed 32-bit int can lead
to undefined behavior if the result exceeds its range. In our
case, an overflow could miscalculate free blocks, potentially
leading to erroneous filesystem accounting.
To ensure the arithmetic is performed in 64-bit space, we cast
"inactags" to s64 before shifting. This defensive fix prevents any
risk of overflow and complies with kernel coding best practices.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
We noticed the kworker in page_pool_release_retry() was waken
up repeatedly and infinitely in production because of the
buggy driver causing the inflight less than 0 and warning
us in page_pool_inflight()[1].
Since the inflight value goes negative, it means we should
not expect the whole page_pool to get back to work normally.
This patch mitigates the adverse effect by not rescheduling
the kworker when detecting the inflight negative in
page_pool_release_retry().
[1]
[Mon Feb 10 20:36:11 2025] ------------[ cut here ]------------
[Mon Feb 10 20:36:11 2025] Negative(-51446) inflight packet-pages
...
[Mon Feb 10 20:36:11 2025] Call Trace:
[Mon Feb 10 20:36:11 2025] page_pool_release_retry+0x23/0x70
[Mon Feb 10 20:36:11 2025] process_one_work+0x1b1/0x370
[Mon Feb 10 20:36:11 2025] worker_thread+0x37/0x3a0
[Mon Feb 10 20:36:11 2025] kthread+0x11a/0x140
[Mon Feb 10 20:36:11 2025] ? process_one_work+0x370/0x370
[Mon Feb 10 20:36:11 2025] ? __kthread_cancel_work+0x40/0x40
[Mon Feb 10 20:36:11 2025] ret_from_fork+0x35/0x40
[Mon Feb 10 20:36:11 2025] ---[ end trace ebffe800f33e7e34 ]---
Note: before this patch, the above calltrace would flood the
dmesg due to repeated reschedule of release_dw kworker.
Fix quirk for CME master keyboards so it not only handles
sysex but also song position pointer, MIDI timing clock, start
and stop messages, and active sensing. All of these can be
output by the CME UF series master keyboards.
Tested with a CME UF6 in a desktop Linux environment as
well as on the Zynthian Raspberry Pi based platform.
quirk_nvidia_hda() forcefully enables HDA controller on all NVIDIA GPUs,
because some buggy BIOSes leave it disabled. However, some dual-GPU
laptops do not have a functional HDA controller in DGPU, and BIOS
disables it on purpose. After quirk_nvidia_hda() reenables this dummy
HDA controller, attempting to probe it fails at azx_first_init(), which
is too late to cancel the probe, as it happens in azx_probe_continue().
The sna_hda_intel driver calls azx_free() and stops the chip, however,
it stays probed, and from the runtime PM point of view, the device
remains active (it was set as active by the PCI subsystem on probe). It
prevents vga_switcheroo from turning off the DGPU, because
pci_create_device_link() syncs power management for video and audio
devices.
Affected devices should be added to driver_denylist to prevent them from
probing early. This patch helps identify such devices by printing a
warning, and also forces the device to the suspended state to allow
vga_switcheroo turn off DGPU.
This function triggered a null pointer dereference if used to search for
a report that isn't implemented on the device. This happened both for
optional and required reports alike.
The same logic was applied to pidff_find_special_field and although
pidff_init_fields should return an error earlier if one of the required
reports is missing, future modifications could change this logic and
resurface this possible null pointer dereference again.
Envelope struct is always initialized, but the envelope itself is
optional as described in USB PID Device class definition 1.0.
5.1.1.1 Type Specific Block Offsets
...
4) Effects that do not use Condition Blocks use 1 Parameter Block and
an *optional* Envelope Block.
Sending out "empty" envelope breaks force feedback on some devices with
games that use SINE effect + offset to emulate constant force effect, as
well as generally breaking Constant/Periodic effects. One of the affected
brands is Moza Racing.
This change prevents the envelope from being sent if it contains all
0 values while keeping the old behavior of only sending it, if it differs
from the old one.
Changes in v6:
- Simplify the checks to make them clearer
- Fix possible null pointer dereference while calling
pidff_needs_set_envelope
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com> Reviewed-by: Michał Kopeć <michal@nozomi.space> Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Cristóferson Bueno <cbueno81@gmail.com> Tested-by: Pablo Cisneros <patchkez@protonmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Software uses 0 as de-facto infinite lenght on Linux FF apis (SDL),
Linux doesn't actually define anythi as of now, while USB PID defines
NULL (0xffff). Most PID devices do not expect a 0-length effect and
can't interpret it as infinite. This change fixes Force Feedback for
most PID compliant devices.
As most games depend on updating the values of already playing infinite
effects, this is crucial to ensure they will actually work.
Previously, users had to rely on third-party software to do this conversion
and make their PID devices usable.
Co-developed-by: Makarenko Oleg <oleg@makarenk.ooo> Signed-off-by: Makarenko Oleg <oleg@makarenk.ooo> Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com> Reviewed-by: Michał Kopeć <michal@nozomi.space> Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Cristóferson Bueno <cbueno81@gmail.com> Tested-by: Pablo Cisneros <patchkez@protonmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a character array without a terminating NUL character has a static
initializer, GCC 15's -Wunterminated-string-initialization will only
warn if the array lacks the "nonstring" attribute[1]. Mark the arrays
with __nonstring to and correctly identify the char array as "not a C
string" and thereby eliminate the warning.
Currently armpmu_add() tries to handle a newly-allocated counter having
a stale associated event, but this should not be possible, and if this
were to happen the current mitigation is insufficient and potentially
expensive. It would be better to warn if we encounter the impossible
case.
Calls to pmu::add() and pmu::del() are serialized by the core perf code,
and armpmu_del() clears the relevant slot in pmu_hw_events::events[]
before clearing the bit in pmu_hw_events::used_mask such that the
counter can be reallocated. Thus when armpmu_add() allocates a counter
index from pmu_hw_events::used_mask, it should not be possible to observe
a stale even in pmu_hw_events::events[] unless either
pmu_hw_events::used_mask or pmu_hw_events::events[] have been corrupted.
If this were to happen, we'd end up with two events with the same
event->hw.idx, which would clash with each other during reprogramming,
deletion, etc, and produce bogus results. Add a WARN_ON_ONCE() for this
case so that we can detect if this ever occurs in practice.
That possiblity aside, there's no need to call arm_pmu::disable(event)
for the new event. The PMU reset code initialises the counter in a
disabled state, and armpmu_del() will disable the counter before it can
be reused. Remove the redundant disable.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Tested-by: James Clark <james.clark@linaro.org> Link: https://lore.kernel.org/r/20250218-arm-brbe-v19-v20-2-4e9922fc2e8e@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running in a virtual machine, we might see the original hardware CPU
vendor string (i.e. "AuthenticAMD"), but a model and family ID set by the
hypervisor. In case we run on AMD hardware and the hypervisor sets a model
ID < 0x14, the LAHF cpu feature is eliminated from the the list of CPU
capabilities present to circumvent a bug with some BIOSes in conjunction with
AMD K8 processors.
Parsing the flags list from /proc/cpuinfo seems to be happening mostly in
bash scripts and prebuilt Docker containers, as it does not need to have
additionals tools present – even though more reliable ways like using "kcpuid",
which calls the CPUID instruction instead of parsing a list, should be preferred.
Scripts, that use /proc/cpuinfo to determine if the current CPU is
"compliant" with defined microarchitecture levels like x86-64-v2 will falsely
claim the CPU is incapable of modern CPU instructions when "lahf_lm" is missing
in that flags list.
This can prevent some docker containers from starting or build scripts to create
unoptimized binaries.
Admittably, this is more a small inconvenience than a severe bug in the kernel
and the shoddy scripts that rely on parsing /proc/cpuinfo
should be fixed instead.
This patch adds an additional check to see if we're running inside a
virtual machine (X86_FEATURE_HYPERVISOR is present), which, to my
understanding, can't be present on a real K8 processor as it was introduced
only with the later/other Athlon64 models.
Example output with the "lahf_lm" flag missing in the flags list
(should be shown between "hypervisor" and "abm"):
$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 6
model name : Common KVM processor
stepping : 1
microcode : 0x1000065
cpu MHz : 2599.998
cache size : 512 KB
physical id : 0
siblings : 1
core id : 0
cpu cores : 1
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx rdtscp
lm rep_good nopl cpuid extd_apicid tsc_known_freq pni
pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt
tsc_deadline_timer aes xsave avx f16c hypervisor abm
3dnowprefetch vmmcall bmi1 avx2 bmi2 xsaveopt
... while kcpuid shows the feature to be present in the CPU:
# kcpuid -d | grep lahf
lahf_lm - LAHF/SAHF available in 64-bit mode
[ mingo: Updated the comment a bit, incorporated Boris's review feedback. ]
Loosen the permission check on forced umount to allow users holding
CAP_SYS_ADMIN privileges in namespaces that are privileged with respect
to the userns that originally mounted the filesystem.
The value of 'ff' is irrelevant, any address will be matched
as long as the other octets are the same.
This is because of too-early register clobbering:
ymm7 is reloaded with new packet data (pkt[9]) but it still holds data
of an earlier load that wasn't processed yet.
The existing tests in nft_concat_range.sh selftests do exercise this code
path, but do not trigger incorrect matching due to the network prefix
limitation.
Ensure we have enough data in linear buffer from skb before accessing
initial bytes. This prevents potential out-of-bounds accesses
when processing short packets.
When ppp_sync_txmung receives an incoming package with an empty
payload:
(remote) gef➤ p *(struct pppoe_hdr *) (skb->head + skb->network_header)
$18 = {
type = 0x1,
ver = 0x1,
code = 0x0,
sid = 0x2,
length = 0x0,
tag = 0xffff8880371cdb96
}
from the skb struct (trimmed)
tail = 0x16,
end = 0x140,
head = 0xffff88803346f400 "4",
data = 0xffff88803346f416 ":\377",
truesize = 0x380,
len = 0x0,
data_len = 0x0,
mac_len = 0xe,
hdr_len = 0x0,
The newly element to be added to the list is the first argument of
list_add_tail. This fix is missing dcfad4ab4d67 ("nvmet-fcloop: swap
the list_add_tail arguments").
Fixes: 437c0b824dbd ("nvme-fcloop: add target to host LS request support") Signed-off-by: Daniel Wagner <wagi@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function pdc20621_prog_dimm0() calls the function pdc20621_i2c_read()
but does not handle the error if the read fails. This could lead to
process with invalid data. A proper implementation can be found in
/source/drivers/ata/sata_sx4.c, pdc20621_prog_dimm_global(). As mentioned
in its commit: bb44e154e25125bef31fa956785e90fccd24610b, the variable spd0
might be used uninitialized when pdc20621_i2c_read() fails.
Add error handling to pdc20621_i2c_read(). If a read operation fails,
an error message is logged via dev_err(), and return a negative error
code.
Add error handling to pdc20621_prog_dimm0() in pdc20621_dimm_init(), and
return a negative error code if pdc20621_prog_dimm0() fails.
Fixes: 4447d3515616 ("libata: convert the remaining SATA drivers to new init model") Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Reviewed-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot discovered that it can disconnect a TLS socket and then
run into all sort of unexpected corner cases. I have a vague
recollection of Eric pointing this out to us a long time ago.
Supporting disconnect is really hard, for one thing if offload
is enabled we'd need to wait for all packets to be _acked_.
Disconnect is not commonly used, disallow it.
The immediate problem syzbot run into is the warning in the strp,
but that's just the easiest bug to trigger:
In case the backlog transmit queue for system-importance messages is overloaded,
tipc_link_xmit() returns -ENOBUFS but the skb list is not purged. This leads to
memory leak and failure when a skb is allocated.
This commit fixes this issue by purging the skb list before tipc_link_xmit()
returns.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Signed-off-by: Tung Nguyen <tung.quang.nguyen@est.tech> Link: https://patch.msgid.link/20250403092431.514063-1-tung.quang.nguyen@est.tech Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_ioremap() returns NULL on error. Currently, pxa_ata_probe() does
not check for this case, which can result in a NULL pointer dereference.
Add NULL check after devm_ioremap() to prevent this issue.
Fixes: 2dc6c6f15da9 ("[ARM] pata_pxa: DMA-capable PATA driver") Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An update was made to up the module ref count when a synthetic event is
registered for both trace and perf events. But if perf is not configured
in, the perf enums used will cause the kernel to fail to build.
Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Douglas Raillard <douglas.raillard@arm.com> Link: https://lore.kernel.org/20250323152151.528b5ced@batman.local.home Fixes: 21581dd4e7ff ("tracing: Ensure module defining synth event cannot be unloaded while tracing") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202503232230.TeREVy8R-lkp@intel.com/ Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
b3e34a47f989 ("x86/kexec: fix memory leak of elf header buffer"),
freeing image->elf_headers in the error path of crash_load_segments()
is not needed because kimage_file_post_load_cleanup() will take
care of that later. And not clearing it could result in a double-free.
Drop the superfluous vfree() call at the error path of
crash_load_segments().
Unlike atomic_inc_not_zero, refcount_inc_not_zero is not a full barrier.
conntrack uses SLAB_TYPESAFE_BY_RCU, i.e. it is possible that a 'newly'
allocated object is still in use on another CPU:
CPU1 CPU2
encounter 'ct' during hlist walk
delete_from_lists
refcount drops to 0
kmem_cache_free(ct);
__nf_conntrack_alloc() // returns same object
refcount_inc_not_zero(ct); /* might fail */
/* If set, ct is public/in the hash table */
test_bit(IPS_CONFIRMED_BIT, &ct->status);
In case CPU1 already set refcount back to 1, refcount_inc_not_zero()
will succeed.
The expected possibilities for a CPU that obtained the object 'ct'
(but no reference so far) are:
1. refcount_inc_not_zero() fails. CPU2 ignores the object and moves to
the next entry in the list. This happens for objects that are about
to be free'd, that have been free'd, or that have been reallocated
by __nf_conntrack_alloc(), but where the refcount has not been
increased back to 1 yet.
2. refcount_inc_not_zero() succeeds. CPU2 checks the CONFIRMED bit
in ct->status. If set, the object is public/in the table.
If not, the object must be skipped; CPU2 calls nf_ct_put() to
un-do the refcount increment and moves to the next object.
Parallel deletion from the hlists is prevented by a
'test_and_set_bit(IPS_DYING_BIT, &ct->status);' check, i.e. only one
cpu will do the unlink, the other one will only drop its reference count.
Because refcount_inc_not_zero is not a full barrier, CPU2 may try to
delete an object that is not on any list:
1. refcount_inc_not_zero() successful (refcount inited to 1 on other CPU)
2. CONFIRMED test also successful (load was reordered or zeroing
of ct->status not yet visible)
3. delete_from_lists unlinks entry not on the hlist, because
IPS_DYING_BIT is 0 (already cleared).
2) is already wrong: CPU2 will handle a partially initited object
that is supposed to be private to CPU1.
Add needed barriers when refcount_inc_not_zero() is successful.
It also inserts a smp_wmb() before the refcount is set to 1 during
allocation.
Because other CPU might still see the object, refcount_set(1)
"resurrects" it, so we need to make sure that other CPUs will also observe
the right content. In particular, the CONFIRMED bit test must only pass
once the object is fully initialised and either in the hash or about to be
inserted (with locks held to delay possible unlink from early_drop or
gc worker).
I did not change flow_offload_alloc(), as far as I can see it should call
refcount_inc(), not refcount_inc_not_zero(): the ct object is attached to
the skb so its refcount should be >= 1 in all cases.
v2: prefer smp_acquire__after_ctrl_dep to smp_rmb (Will Deacon).
v3: keep smp_acquire__after_ctrl_dep close to refcount_inc_not_zero call
add comment in nf_conntrack_netlink, no control dependency there
due to locks.
Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/all/Yr7WTfd6AVTQkLjI@e126311.manchester.arm.com/ Reported-by: Kajetan Puchalski <kajetan.puchalski@arm.com> Diagnosed-by: Will Deacon <will@kernel.org> Fixes: 719774377622 ("netfilter: conntrack: convert to refcount_t api") Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NFSD sends CB_RECALL_ANY to clients when the server is low on
memory or that client has a large number of delegations outstanding.
We've seen cases where NFSD attempts to send CB_RECALL_ANY requests
to disconnected clients, and gets confused. These calls never go
anywhere if a backchannel transport to the target client isn't
available. Before the server can send any backchannel operation, the
client has to connect first and then do a BIND_CONN_TO_SESSION.
This patch doesn't address the root cause of the confusion, but
there's no need to queue up these optional operations if they can't
go anywhere.
Fixes: 44df6f439a17 ("NFSD: add delegation reaper to react to low memory condition") Reviewed-by: Jeff Layton <jlayton@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before calling nfsd4_run_cb to queue dl_recall to the callback_wq, we
increment the reference count of dl_stid.
We expect that after the corresponding work_struct is processed, the
reference count of dl_stid will be decremented through the callback
function nfsd4_cb_recall_release.
However, if the call to nfsd4_run_cb fails, the incremented reference
count of dl_stid will not be decremented correspondingly, leading to the
following nfs4_stid leak:
unreferenced object 0xffff88812067b578 (size 344):
comm "nfsd", pid 2761, jiffies 4295044002 (age 5541.241s)
hex dump (first 32 bytes):
01 00 00 00 6b 6b 6b 6b b8 02 c0 e2 81 88 ff ff ....kkkk........
00 6b 6b 6b 6b 6b 6b 6b 00 00 00 00 ad 4e ad de .kkkkkkk.....N..
backtrace:
kmem_cache_alloc+0x4b9/0x700
nfsd4_process_open1+0x34/0x300
nfsd4_open+0x2d1/0x9d0
nfsd4_proc_compound+0x7a2/0xe30
nfsd_dispatch+0x241/0x3e0
svc_process_common+0x5d3/0xcc0
svc_process+0x2a3/0x320
nfsd+0x180/0x2e0
kthread+0x199/0x1d0
ret_from_fork+0x30/0x50
ret_from_fork_asm+0x1b/0x30
unreferenced object 0xffff8881499f4d28 (size 368):
comm "nfsd", pid 2761, jiffies 4295044005 (age 5541.239s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 30 4d 9f 49 81 88 ff ff ........0M.I....
30 4d 9f 49 81 88 ff ff 20 00 00 00 01 00 00 00 0M.I.... .......
backtrace:
kmem_cache_alloc+0x4b9/0x700
nfs4_alloc_stid+0x29/0x210
alloc_init_deleg+0x92/0x2e0
nfs4_set_delegation+0x284/0xc00
nfs4_open_delegation+0x216/0x3f0
nfsd4_process_open2+0x2b3/0xee0
nfsd4_open+0x770/0x9d0
nfsd4_proc_compound+0x7a2/0xe30
nfsd_dispatch+0x241/0x3e0
svc_process_common+0x5d3/0xcc0
svc_process+0x2a3/0x320
nfsd+0x180/0x2e0
kthread+0x199/0x1d0
ret_from_fork+0x30/0x50
ret_from_fork_asm+0x1b/0x30
Fix it by checking the result of nfsd4_run_cb and call nfs4_put_stid if
fail to queue dl_recall.
Cc: stable@vger.kernel.org Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the "size_check" label in ea_get(), the code checks if the extended
attribute list (xattr) size matches ea_size. If not, it logs
"ea_get: invalid extended attribute" and calls print_hex_dump().
Here, EALIST_SIZE(ea_buf->xattr) returns 4110417968, which exceeds
INT_MAX (2,147,483,647). Then ea_size is clamped:
int size = clamp_t(int, ea_size, 0, EALIST_SIZE(ea_buf->xattr));
Although clamp_t aims to bound ea_size between 0 and 4110417968, the upper
limit is treated as an int, causing an overflow above 2^31 - 1. This leads
"size" to wrap around and become negative (-184549328).
The "size" is then passed to print_hex_dump() (called "len" in
print_hex_dump()), it is passed as type size_t (an unsigned
type), this is then stored inside a variable called
"int remaining", which is then assigned to "int linelen" which
is then passed to hex_dump_to_buffer(). In print_hex_dump()
the for loop, iterates through 0 to len-1, where len is 18446744073525002176, calling hex_dump_to_buffer()
on each iteration:
for (i = 0; i < len; i += rowsize) {
linelen = min(remaining, rowsize);
remaining -= rowsize;
hex_dump_to_buffer(ptr + i, linelen, rowsize, groupsize,
linebuf, sizeof(linebuf), ascii);
...
}
The expected stopping condition (i < len) is effectively broken
since len is corrupted and very large. This eventually leads to
the "ptr+i" being passed to hex_dump_to_buffer() to get closer
to the end of the actual bounds of "ptr", eventually an out of
bounds access is done in hex_dump_to_buffer() in the following
for loop:
Mounting a corrupted filesystem with directory which contains '.' dir
entry with rec_len == block size results in out-of-bounds read (later
on, when the corrupted directory is removed).
ext4_empty_dir() assumes every ext4 directory contains at least '.'
and '..' as directory entries in the first data block. It first loads
the '.' dir entry, performs sanity checks by calling ext4_check_dir_entry()
and then uses its rec_len member to compute the location of '..' dir
entry (in ext4_next_entry). It assumes the '..' dir entry fits into the
same data block.
If the rec_len of '.' is precisely one block (4KB), it slips through the
sanity checks (it is considered the last directory entry in the data
block) and leaves "struct ext4_dir_entry_2 *de" point exactly past the
memory slot allocated to the data block. The following call to
ext4_check_dir_entry() on new value of de then dereferences this pointer
which results in out-of-bounds mem access.
Fix this by extending __ext4_check_dir_entry() to check for '.' dir
entries that reach the end of data block. Make sure to ignore the phony
dir entries for checksum (by checking name_len for non-zero).
Note: This is reported by KASAN as use-after-free in case another
structure was recently freed from the slot past the bound, but it is
really an OOB read.
This fixes an analogus bug that was fixed in xfs in commit 4b8d867ca6e2 ("xfs: don't over-report free space or inodes in
statvfs") where statfs can report misleading / incorrect information
where project quota is enabled, and the free space is less than the
remaining quota.
This commit will resolve a test failure in generic/762 which tests for
this bug.
Currently, using synth_event_delete() will fail if the event is being
used (tracing in progress), but that is normally done in the module exit
function. At that stage, failing is problematic as returning a non-zero
status means the module will become locked (impossible to unload or
reload again).
Instead, ensure the module exit function does not get called in the
first place by increasing the module refcnt when the event is enabled.
Kairui reported a UAF issue in print_graph_function_flags() during
ftrace stress testing [1]. This issue can be reproduced if puting a
'mdelay(10)' after 'mutex_unlock(&trace_types_lock)' in s_start(),
and executing the following script:
$ echo function_graph > current_tracer
$ cat trace > /dev/null &
$ sleep 5 # Ensure the 'cat' reaches the 'mdelay(10)' point
$ echo timerlat > current_tracer
The root cause lies in the two calls to print_graph_function_flags
within print_trace_line during each s_show():
* One through 'iter->trace->print_line()';
* Another through 'event->funcs->trace()', which is hidden in
print_trace_fmt() before print_trace_line returns.
Tracer switching only updates the former, while the latter continues
to use the print_line function of the old tracer, which in the script
above is print_graph_function_flags.
Moreover, when switching from the 'function_graph' tracer to the
'timerlat' tracer, s_start only calls graph_trace_close of the
'function_graph' tracer to free 'iter->private', but does not set
it to NULL. This provides an opportunity for 'event->funcs->trace()'
to use an invalid 'iter->private'.
To fix this issue, set 'iter->private' to NULL immediately after
freeing it in graph_trace_close(), ensuring that an invalid pointer
is not passed to other tracers. Additionally, clean up the unnecessary
'iter->private = NULL' during each 'cat trace' when using wakeup and
irqsoff tracers.
Set the MMC_CAP_NEED_RSP_BUSY capability for the sdhci-pxav3 host to
prevent conversion of R1B responses to R1. Without this, the eMMC card
in the samsung,coreprimevelte smartphone using the Marvell PXA1908 SoC
with this mmc host doesn't probe with the ETIMEDOUT error originating in
__mmc_poll_for_busy.
Note that the other issues reported for this phone and host, namely
floods of "Tuning failed, falling back to fixed sampling clock" dmesg
messages for the eMMC and unstable SDIO are not mitigated by this
change.
Like the ASUS Vivobook X1504VAP and Vivobook X1704VAP, the ASUS Vivobook 14
X1404VAP has its keyboard IRQ (1) described as ActiveLow in the DSDT, which
the kernel overrides to EdgeHigh breaking the keyboard.
$ sudo dmidecode
[…]
System Information
Manufacturer: ASUSTeK COMPUTER INC.
Product Name: ASUS Vivobook 14 X1404VAP_X1404VA
[…]
$ grep -A 30 PS2K dsdt.dsl | grep IRQ -A 1
IRQ (Level, ActiveLow, Exclusive, )
{1}
Add the X1404VAP to the irq1_level_low_skip_override[] quirk table to fix
this.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219224 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Anton Shyndin <mrcold.il@gmail.com> Link: https://patch.msgid.link/20250318160903.77107-1-pmenzel@molgen.mpg.de Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller has reported a warning in to_nfit_bus_uuid(): "only secondary
bus families can be translated". This warning is emited if the argument
is equal to NVDIMM_BUS_FAMILY_NFIT == 0. Function acpi_nfit_ctl() first
verifies that a user-provided value call_pkg->nd_family of type u64 is
not equal to 0. Then the value is converted to int, and only after that
is compared to NVDIMM_BUS_FAMILY_MAX. This can lead to passing an invalid
argument to acpi_nfit_ctl(), if call_pkg->nd_family is non-zero, while
the lower 32 bits are zero.
Furthermore, it is best to return EINVAL immediately upon seeing the
invalid user input. The WARNING is insufficient to prevent further
undefined behavior based on other invalid user input.
All checks of the input value should be applied to the original variable
call_pkg->nd_family.
On the following path, flush_tlb_range() can be used for zapping normal
PMD entries (PMD entries that point to page tables) together with the PTE
entries in the pointed-to page table:
The arm64 version of flush_tlb_range() has a comment describing that it can
be used for page table removal, and does not use any last-level
invalidation optimizations. Fix the X86 version by making it behave the
same way.
Currently, X86 only uses this information for the following two purposes,
which I think means the issue doesn't have much impact:
- In native_flush_tlb_multi() for checking if lazy TLB CPUs need to be
IPI'd to avoid issues with speculative page table walks.
- In Hyper-V TLB paravirtualization, again for lazy TLB stuff.
The patch "x86/mm: only invalidate final translations with INVLPGB" which
is currently under review (see
<https://lore.kernel.org/all/20241230175550.4046587-13-riel@surriel.com/>)
would probably be making the impact of this a lot worse.
TSC could be reset in deep ACPI sleep states, even with invariant TSC.
That's the reason we have sched_clock() save/restore functions, to deal
with this situation. But what happens is that such functions are guarded
with a check for the stability of sched_clock - if not considered stable,
the save/restore routines aren't executed.
On top of that, we have a clear comment in native_sched_clock() saying
that *even* with TSC unstable, we continue using TSC for sched_clock due
to its speed.
In other words, if we have a situation of TSC getting detected as unstable,
it marks the sched_clock as unstable as well, so subsequent S3 sleep cycles
could bring bogus sched_clock values due to the lack of the save/restore
mechanism, causing warnings like this:
[22.954918] ------------[ cut here ]------------
[22.954923] Delta way too big! 18446743750843854390 ts=18446744072977390405 before=322133536015 after=322133536015 write stamp=18446744072977390405
[22.954923] If you just came from a suspend/resume,
[22.954923] please switch to the trace global clock:
[22.954923] echo global > /sys/kernel/tracing/trace_clock
[22.954923] or add trace_clock=global to the kernel command line
[22.954937] WARNING: CPU: 2 PID: 5728 at kernel/trace/ring_buffer.c:2890 rb_add_timestamp+0x193/0x1c0
Notice that the above was reproduced even with "trace_clock=global".
The fix for that is to _always_ save/restore the sched_clock on suspend
cycle _if TSC is used_ as sched_clock - only if we fallback to jiffies
the sched_clock_stable() check becomes relevant to save/restore the
sched_clock.
Debugged-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: stable@vger.kernel.org Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/20250215210314.351480-1-gpiccoli@igalia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function call “dmaengine_unmap_put(unmap)” was used in an if branch.
The same call was immediately triggered by a subsequent goto statement.
Thus avoid such a call repetition.
This issue was detected by using the Coccinelle software.
Fixes: 5648e56d03fa ("NTB: ntb_perf: Add full multi-port NTB API support") Cc: stable@vger.kernel.org Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Alex Hung <alex.hung@amd.com> Acked-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Hersen Wu <hersenxs.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[get_pipe_idx() was introduced as a helper by dda4fb85e433 ("drm/amd/display: DML changes for DCN32/321") in v6.0.
This patch backports it to make code clearer. And minor conflict is
resolved due to code context change.] Signed-off-by: Jianqi Ren <jianqi.ren.cn@windriver.com> Signed-off-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the LPUART reference manual, TXRTSE and TXRTSPOL of MODIR
register only can be changed when the transmitter is disabled.
So disable the transmitter before changing RS485 related registers and
re-enable it after the change is done.
Fixes: 67b01837861c ("tty: serial: lpuart: Add RS485 support for 32-bit uart flavour") Cc: stable <stable@kernel.org> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20250312022503.1342990-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM.
So here should configure the corresponding UARTMODIR register bits to
avoid confusion.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230414022111.20896-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f5cb528d6441 ("tty: serial: fsl_lpuart: disable transmitter before changing RS485 related registers") Signed-off-by: Sasha Levin <sashal@kernel.org>
After a suspend/resume cycle on a down interface, it will come up as
ERROR-ACTIVE.
$ ip -details -s -s a s dev flexcan0
3: flexcan0: <NOARP,ECHO> mtu 16 qdisc pfifo_fast state DOWN group default qlen 10
link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
can state STOPPED (berr-counter tx 0 rx 0) restart-ms 1000
$ sudo systemctl suspend
$ ip -details -s -s a s dev flexcan0
3: flexcan0: <NOARP,ECHO> mtu 16 qdisc pfifo_fast state DOWN group default qlen 10
link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 1000
And only set CAN state to CAN_STATE_ERROR_ACTIVE when resume process
has no issue, otherwise keep in CAN_STATE_SLEEPING as suspend did.
devm_kasprintf() returns NULL when memory allocation fails. Currently,
com20020pci_probe() does not check for this case, which results in a
NULL pointer dereference.
Add NULL check after devm_kasprintf() to prevent this issue and ensure
no resources are left allocated.
Fixes: 6b17a597fc2f ("arcnet: restoring support for multiple Sohard Arcnet cards") Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com> Link: https://patch.msgid.link/20250402135036.44697-1-bsdhenrymartin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
struct geneve_opt uses 5 bit length for each single option, which
means every vary size option should be smaller than 128 bytes.
However, all current related Netlink policies cannot promise this
length condition and the attacker can exploit a exact 128-byte size
option to *fake* a zero length option and confuse the parsing logic,
further achieve heap out-of-bounds read.
Fix these issues by enforing correct length condition in related
policies.
Fixes: 925d844696d9 ("netfilter: nft_tunnel: add support for geneve opts") Fixes: 4ece47787077 ("lwtunnel: add options setting and dumping for geneve") Fixes: 0ed5269f9e41 ("net/sched: add tunnel option support to act_tunnel_key") Fixes: 0a6e77784f49 ("net/sched: allow flower to match tunnel options") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://patch.msgid.link/20250402165632.6958-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mv88e6xxx has an internal PPU that polls PHY state. If we want to
access the internal PHYs, we need to disable the PPU first. Because
that is a slow operation, a 10ms timer is used to re-enable it,
canceled with every access, so bulk operations effectively only
disable it once and re-enable it some 10ms after the last access.
If a PHY is accessed and then the mv88e6xxx module is removed before
the 10ms are up, the PPU re-enable ends up accessing a dangling pointer.
This especially affects probing during bootup. The MDIO bus and PHY
registration may succeed, but registration with the DSA framework
may fail later on (e.g. because the CPU port depends on another,
very slow device that isn't done probing yet, returning -EPROBE_DEFER).
In this case, probe() fails, but the MDIO subsystem may already have
accessed the MIDO bus or PHYs, arming the timer.
This is fixed as follows:
- If probe fails after mv88e6xxx_phy_init(), make sure we also call
mv88e6xxx_phy_destroy() before returning
- In mv88e6xxx_remove(), make sure we do the teardown in the correct
order, calling mv88e6xxx_phy_destroy() after unregistering the
switch device.
- In mv88e6xxx_phy_destroy(), destroy both the timer and the work item
that the timer might schedule, synchronously waiting in case one of
the callbacks already fired and destroying the timer first, before
waiting for the work item.
- Access to the PPU is guarded by a mutex, the worker acquires it
with a mutex_trylock(), not proceeding with the expensive shutdown
if that fails. We grab the mutex in mv88e6xxx_phy_destroy() to make
sure the slow PPU shutdown is already done or won't even enter, when
we wait for the work item.
Fixes: 2e5f032095ff ("dsa: add support for the Marvell 88E6131 switch chip") Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://patch.msgid.link/20250401135705.92760-1-david.oberhollenzer@sigma-star.at Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using RTEXT_FILTER_SKIP_STATS is incorrectly skipping non-stats IPv6
netlink attributes on link dump. This causes issues on userspace tools,
e.g iproute2 is not rendering address generation mode as it should due
to missing netlink attribute.
Move the filling of IFLA_INET6_STATS and IFLA_INET6_ICMP6STATS to a
helper function guarded by a flag check to avoid hitting the same
situation in the future.
Fixes: d5566fd72ec1 ("rtnetlink: RTEXT_FILTER_SKIP_STATS support to avoid dumping inet/inet6 stats") Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250402121751.3108-1-ffmancera@riseup.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When handling multiple NFTA_TUNNEL_KEY_OPTS_GENEVE attributes, the
parsing logic should place every geneve_opt structure one by one
compactly. Hence, when deciding the next geneve_opt position, the
pointer addition should be in units of char *.
However, the current implementation erroneously does type conversion
before the addition, which will lead to heap out-of-bounds write.
Fix this bug with correct pointer addition and conversion in parse
and dump code.
Fixes: 925d844696d9 ("netfilter: nft_tunnel: add support for geneve opts") Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because skb_tunnel_check_pmtu() doesn't handle PACKET_HOST packets,
commit 30a92c9e3d6b ("openvswitch: Set the skbuff pkt_type for proper
pmtud support.") forced skb->pkt_type to PACKET_OUTGOING for
openvswitch packets that are sent using the OVS_ACTION_ATTR_OUTPUT
action. This allowed such packets to invoke the
iptunnel_pmtud_check_icmp() or iptunnel_pmtud_check_icmpv6() helpers
and thus trigger PMTU update on the input device.
However, this also broke other parts of PMTU discovery. Since these
packets don't have the PACKET_HOST type anymore, they won't trigger the
sending of ICMP Fragmentation Needed or Packet Too Big messages to
remote hosts when oversized (see the skb_in->pkt_type condition in
__icmp_send() for example).
These two skb->pkt_type checks are therefore incompatible as one
requires skb->pkt_type to be PACKET_HOST, while the other requires it
to be anything but PACKET_HOST.
It makes sense to not trigger ICMP messages for non-PACKET_HOST packets
as these messages should be generated only for incoming l2-unicast
packets. However there doesn't seem to be any reason for
skb_tunnel_check_pmtu() to ignore PACKET_HOST packets.
Allow both cases to work by allowing skb_tunnel_check_pmtu() to work on
PACKET_HOST packets and not overriding skb->pkt_type in openvswitch
anymore.
Fixes: 30a92c9e3d6b ("openvswitch: Set the skbuff pkt_type for proper pmtud support.") Fixes: 4cb47a8644cc ("tunnels: PMTU discovery support for directly bridged IP packets") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Aaron Conole <aconole@redhat.com> Tested-by: Aaron Conole <aconole@redhat.com> Link: https://patch.msgid.link/eac941652b86fddf8909df9b3bf0d97bc9444793.1743208264.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a peer attempts to establish a connection, vsock_connect() contains
a loop that waits for the state to be TCP_ESTABLISHED. However, the
other peer can be fast enough to accept the connection and close it
immediately, thus moving the state to TCP_CLOSING.
When this happens, the peer in the vsock_connect() is properly woken up,
but since the state is not TCP_ESTABLISHED, it goes back to sleep
until the timeout expires, returning -ETIMEDOUT.
If the socket state is TCP_CLOSING, waiting for the timeout is pointless.
vsock_connect() can return immediately without errors or delay since the
connection actually happened. The socket will be in a closing state,
but this is not an issue, and subsequent calls will fail as expected.
We discovered this issue while developing a test that accepts and
immediately closes connections to stress the transport switch between
two connect() calls, where the first one was interrupted by a signal
(see Closes link).
Reported-by: Luigi Leonardi <leonardi@redhat.com> Closes: https://lore.kernel.org/virtualization/bq6hxrolno2vmtqwcvb5bljfpb7mvwb3kohrvaed6auz5vxrfv@ijmd2f3grobn/ Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Tested-by: Luigi Leonardi <leonardi@redhat.com> Reviewed-by: Luigi Leonardi <leonardi@redhat.com> Link: https://patch.msgid.link/20250328141528.420719-1-sgarzare@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the current implementation, skbprio enqueue/dequeue contains an assertion
that fails under certain conditions when SKBPRIO is used as a child qdisc under
TBF with specific parameters. The failure occurs because TBF sometimes peeks at
packets in the child qdisc without actually dequeuing them when tokens are
unavailable.
This peek operation creates a discrepancy between the parent and child qdisc
queue length counters. When TBF later receives a high-priority packet,
SKBPRIO's queue length may show a different value than what's reflected in its
internal priority queue tracking, triggering the assertion.
The fix removes this overly strict assertions in SKBPRIO, they are not
necessary at all.
When calling netlbl_conn_setattr(), addr->sa_family is used
to determine the function behavior. If sk is an IPv4 socket,
but the connect function is called with an IPv6 address,
the function calipso_sock_setattr() is triggered.
Inside this function, the following code is executed:
sk_fullsock(__sk) ? inet_sk(__sk)->pinet6 : NULL;
Since sk is an IPv4 socket, pinet6 is NULL, leading to a
null pointer dereference.
This patch fixes the issue by checking if inet6_sk(sk)
returns a NULL pointer before accessing pinet6.
Signed-off-by: Debin Zhu <mowenroot@163.com> Signed-off-by: Bitao Ouyang <1985755126@qq.com> Acked-by: Paul Moore <paul@paul-moore.com> Fixes: ceba1832b1b2 ("calipso: Set the calipso socket label to match the secattr.") Link: https://patch.msgid.link/20250401124018.4763-1-mowenroot@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a kernel API ntb_mw_clear_trans() would pass 0 to both addr and
size. This would make xlate_pos negative.
[ 23.734156] switchtec switchtec0: MW 0: part 0 addr 0x0000000000000000 size 0x0000000000000000
[ 23.734158] ================================================================================
[ 23.734172] UBSAN: shift-out-of-bounds in drivers/ntb/hw/mscc/ntb_hw_switchtec.c:293:7
[ 23.734418] shift exponent -1 is negative
Ensuring xlate_pos is a positive or zero before BIT.
Fixes: 1e2fd202f859 ("ntb_hw_switchtec: Check for alignment of the buffer in mw_set_trans()") Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's called from spufs_fill_dir(), and caller of that will do
spufs_rmdir() in case of failure. That does remove everything
we'd managed to create, but... the problem dentry is still
negative. IOW, it needs to be explicitly dropped.
In can_send() and can_receive() CAN messages and CAN filter matches are
counted to be visible in the CAN procfs files.
KCSAN detected a data race within can_send() when two CAN frames have
been generated by a timer event writing to the same CAN netdevice at the
same time. Use atomic operations to access the statistics in the hot path
to fix the KCSAN complaint.
Reported-by: syzbot+78ce4489b812515d5e4d@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/67cd717d.050a0220.e1a89.0006.GAE@google.com Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://patch.msgid.link/20250310143353.3242-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a fixup to enable the mute LED on HP Pavilion x360 Convertible
14-dy1xxx with ALC295 codec. The appropriate coefficient index and bits
were identified through a brute-force method, as detailed in
https://bbs.archlinux.org/viewtopic.php?pid=2079504#p2079504.
A circular lock dependency splat has been seen involving down_trylock():
======================================================
WARNING: possible circular locking dependency detected
6.12.0-41.el10.s390x+debug
------------------------------------------------------
dd/32479 is trying to acquire lock: 0015a20accd0d4f8 ((console_sem).lock){-.-.}-{2:2}, at: down_trylock+0x26/0x90
but task is already holding lock: 000000017e461698 (&zone->lock){-.-.}-{2:2}, at: rmqueue_bulk+0xac/0x8f0
the existing dependency chain (in reverse order) is:
-> #4 (&zone->lock){-.-.}-{2:2}:
-> #3 (hrtimer_bases.lock){-.-.}-{2:2}:
-> #2 (&rq->__lock){-.-.}-{2:2}:
-> #1 (&p->pi_lock){-.-.}-{2:2}:
-> #0 ((console_sem).lock){-.-.}-{2:2}:
The console_sem -> pi_lock dependency is due to calling try_to_wake_up()
while holding the console_sem raw_spinlock. This dependency can be broken
by using wake_q to do the wakeup instead of calling try_to_wake_up()
under the console_sem lock. This will also make the semaphore's
raw_spinlock become a terminal lock without taking any further locks
underneath it.
The hrtimer_bases.lock is a raw_spinlock while zone->lock is a
spinlock. The hrtimer_bases.lock -> zone->lock dependency happens via
the debug_objects_fill_pool() helper function in the debugobjects code.
Normally a raw_spinlock to spinlock dependency is not legitimate
and will be warned if CONFIG_PROVE_RAW_LOCK_NESTING is enabled,
but debug_objects_fill_pool() is an exception as it explicitly
allows this dependency for non-PREEMPT_RT kernel without causing
PROVE_RAW_LOCK_NESTING lockdep splat. As a result, this dependency is
legitimate and not a bug.
Anyway, semaphore is the only locking primitive left that is still
using try_to_wake_up() to do wakeup inside critical section, all the
other locking primitives had been migrated to use wake_q to do wakeup
outside of the critical section. It is also possible that there are
other circular locking dependencies involving printk/console_sem or
other existing/new semaphores lurking somewhere which may show up in
the future. Let just do the migration now to wake_q to avoid headache
like this.
The ftrace selftest reported a failure because writing -1 to
sched_rt_runtime_us returns -EBUSY. This happens when the possible
CPUs are different from active CPUs.
Active CPUs are part of one root domain, while remaining CPUs are part
of def_root_domain. Since active cpumask is being used, this results in
cpus=0 when a non active CPUs is used in the loop.
Fix it by looping over the online CPUs instead for validating the
bandwidth calculations.
If a data sector on an OFS floppy contains a value > 0x1e8 (the
largest amount of data that fits in the sector after its header), then
an Amiga reading the file can return corrupt data, by taking the
overlarge size at its word and reading past the end of the buffer it
read the disk sector into!
The cause: when affs_write_end_ofs() writes data to an OFS filesystem,
the new size field for a data block was computed by adding the amount
of data currently being written (into the block) to the existing value
of the size field. This is correct if you're extending the file at the
end, but if you seek backwards in the file and overwrite _existing_
data, it can lead to the size field being larger than the maximum
legal value.
This commit changes the calculation so that it sets the size field to
the max of its previous size and the position within the block that we
just wrote up to.
Signed-off-by: Simon Tatham <anakin@pobox.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If I write a file to an OFS floppy image, and try to read it back on
an emulated Amiga running Workbench 1.3, the Amiga reports a disk
error trying to read the file. (That is, it's unable to read it _at
all_, even to copy it to the NIL: device. It isn't a matter of getting
the wrong data and being unable to parse the file format.)
This is because the 'sequence number' field in the OFS data block
header is supposed to be based at 1, but affs writes it based at 0.
All three locations changed by this patch were setting the sequence
number to a variable 'bidx' which was previously obtained by dividing
a file position by bsize, so bidx will naturally use 0 for the first
block. Therefore all three should add 1 to that value before writing
it into the sequence number field.
With this change, the Amiga successfully reads the file.
For data block reference: https://wiki.osdev.org/FFS_(Amiga)
Signed-off-by: Simon Tatham <anakin@pobox.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PCI P2PDMA code will register the CMB block to the memory
hot-plugging subsystem, which have an alignment requirement. Memory
blocks that do not satisfy this alignment requirement (usually 2MB) will
lead to a WARNING from memory hotplugging.
Verify the CMB block's address and size against the alignment and only
try to send CMB blocks compatible with it to prevent this warning.
Tested on Intel DC D4502 SSD, which has a 512K CMB block that is too
small for memory hotplugging (thus PCI P2PDMA).
nvme_tcp_poll() may race with the send path error handler because
it may complete the request while it is actively being polled for
completion, resulting in a UAF panic [1]:
We should make sure to stop polling when we see an error when
trying to read from the socket. Hence make sure to propagate the
error so that the block layer breaks the polling cycle.
The firmware dumps can be pretty big, and since we use single
pages for each SG table entry, even the table itself may end
up being an order-5 allocation. Build chained tables so that
we need not allocate a higher-order table here.
This could be improved and cleaned up, e.g. by using the SG
pool code or simply kvmalloc(), but all of that would require
also updating the devcoredump first since that frees it all,
so we need to be more careful. SG pool might also run against
the CONFIG_ARCH_NO_SG_CHAIN limitation, which is irrelevant
here.
Also use _devcd_free_sgtable() for the error paths now, much
simpler especially since it's in two places now.
sched_smt_active() can be called from noinstr code, so it should always
be inlined. The CONFIG_SCHED_SMT version already has __always_inline.
Do the same for its !CONFIG_SCHED_SMT counterpart.
Fixes the following warning:
vmlinux.o: error: objtool: intel_idle_ibrs+0x13: call to sched_smt_active() leaves .noinstr.text section
When number of RVU VFs > 64, the vfs value passed to "rvu_queue_work"
function is incorrect. Due to which mbox workqueue entries for
VFs 0 to 63 never gets added to workqueue.
Fixes: 9bdc47a6e328 ("octeontx2-af: Mbox communication support btw AF and it's VFs") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250327091441.1284-1-gakula@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Prior to commit 496121c02127 ("ACPI: processor: idle: Allow probing on
platforms with one ACPI C-state"), the acpi_idle driver wouldn't load on
systems without a valid C-State at least as deep as C2.
The behavior was desirable for guests on hypervisors such as VMWare
ESXi, which by default don't have the _CST ACPI method, and set the C2
and C3 latencies to 101 and 1001 microseconds respectively via the FADT,
to signify they're unsupported.
Since the above change though, these virtualized deployments end up
loading acpi_idle, and thus entering the default C1 C-State set by
acpi_processor_get_power_info_default(); this is undesirable for a
system that's communicating to the OS it doesn't want C-States (missing
_CST, and invalid C2/C3 in FADT).
Make acpi_processor_get_power_info_fadt() return -ENODEV in that case,
so that acpi_processor_get_cstate_info() exits early and doesn't set
pr->flags.power = 1.
Fixes: 496121c02127 ("ACPI: processor: idle: Allow probing on platforms with one ACPI C-state") Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz> Reviewed-by: Zhang Rui <rui.zhang@intel.com> Link: https://patch.msgid.link/20250328143040.9348-1-ggherdovich@suse.cz
[ rjw: Changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The calculation of bytes-dropped and bytes_dropped_nested is reversed.
Although it does not affect the final calculation of total_dropped,
it should still be modified.
Link: https://lore.kernel.org/20250223070106.6781-1-yangfeng59949@163.com Fixes: 6c43e554a2a5 ("ring-buffer: Add ring buffer startup selftest") Signed-off-by: Feng Yang <yangfeng@kylinos.cn> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 30aad41721e0 ("net/core: Add support for getting VF GUIDs")
added support for getting VF port and node GUIDs in netlink ifinfo
messages, but their size was not taken into consideration in the
function that allocates the netlink message, causing the following
warning when a netlink message is filled with many VF port and node
GUIDs:
# echo 64 > /sys/bus/pci/devices/0000\:08\:00.0/sriov_numvfs
# ip link show dev ib0
RTNETLINK answers: Message too long
Cannot send link get request: Message too long
In exfat_find_last_cluster(), the cluster chain is traversed until
the EOF cluster. If the cluster chain includes a loop due to file
system corruption, the EOF cluster cannot be traversed, resulting
in an infinite loop.
If the number of clusters indicated by the file size is inconsistent
with the cluster chain length, exfat_find_last_cluster() will return
an error, so if this inconsistency is found, the traversal can be
aborted without traversing to the EOF cluster.
proc_pid_wchan() used to report kernel addresses to user space but that is
no longer the case today. Bring the comment above proc_pid_wchan() in
sync with the implementation.
Link: https://lkml.kernel.org/r/20250319210222.1518771-1-bvanassche@acm.org Fixes: b2f73922d119 ("fs/proc, core/debug: Don't expose absolute kernel addresses via wchan") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Cc: Kees Cook <kees@kernel.org> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pyrf_event__new() method copies the event obtained from the perf
ring buffer to a structure that will then be turned into a python object
for further consumption, so it copies perf_event.header.size bytes to
its 'event' member:
When processing tracepoints the perf python binding was parsing the
event before calling perf_mmap__consume(&md->core) in
pyrf_evlist__read_on_cpu().
But part of this event parsing was to set the perf_sample->raw_data
pointer to the payload of the event, which then could be overwritten by
other event before tracepoint fields were asked for via event.prev_comm
in a python program, for instance.
This also happened with other fields, but strings were were problems
were surfacing, as there is UTF-8 validation for the potentially garbled
data.
This ended up showing up as (with some added debugging messages):
( field 'prev_comm' ret=0x7f7c31f65110, raw_size=68 ) ( field 'prev_pid' ret=0x7f7c23b1bed0, raw_size=68 ) ( field 'prev_prio' ret=0x7f7c239c0030, raw_size=68 ) ( field 'prev_state' ret=0x7f7c239c0250, raw_size=68 ) time 14771421785867 prev_comm= prev_pid=1919907691 prev_prio=796026219 prev_state=0x303a32313175 ==>
( XXX '��' len=16, raw_size=68) ( field 'next_comm' ret=(nil), raw_size=68 ) Traceback (most recent call last):
File "/home/acme/git/perf-tools-next/tools/perf/python/tracepoint.py", line 51, in <module>
main()
File "/home/acme/git/perf-tools-next/tools/perf/python/tracepoint.py", line 46, in main
event.next_comm,
^^^^^^^^^^^^^^^
AttributeError: 'perf.sample_event' object has no attribute 'next_comm'
When event.next_comm was asked for, the PyUnicode_FromString() python
API would fail and that tracepoint field wouldn't be available, stopping
the tools/perf/python/tracepoint.py test tool.
But, since we already do a copy of the whole event in pyrf_event__new,
just use it and while at it remove what was done in in e8968e654191390a
("perf python: Fix pyrf_evlist__read_on_cpu event consuming") because we
don't really need to wait for parsing the sample before declaring the
event as consumed.
This copy is questionable as is now, as it limits the maximum event +
sample_type and tracepoint payload to sizeof(union perf_event), this all
has been "working" because 'struct perf_event_mmap2', the largest entry
in 'union perf_event' is:
To avoid a leak if we have the python object but then something happens
and we need to return the operation, decrement the offset of the newly
created object.
Fixes: 377f698db12150a1 ("perf python: Add struct evsel into struct pyrf_event") Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Reviewed-by: Ian Rogers <irogers@google.com> Link: https://lore.kernel.org/r/20250312203141.285263-5-acme@kernel.org Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The amount of looping through the list of delegations is occasionally
leading to soft lockups. Avoid at least some loops by not requiring the
NFSv4 state manager to scan for delegations that are marked for
return-on-close. Instead, either mark them for immediate return (if
possible) or else leave it up to nfs4_inode_return_delegation_on_close()
to return them once the file is closed by the application.
Fixes: b757144fd77c ("NFSv4: Be less aggressive about returning delegations for open files") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "powerpc/crash: use generic crashkernel reservation", v3.
Commit 0ab97169aa05 ("crash_core: add generic function to do reservation")
added a generic function to reserve crashkernel memory. So let's use the
same function on powerpc and remove the architecture-specific code that
essentially does the same thing.
The generic crashkernel reservation also provides a way to split the
crashkernel reservation into high and low memory reservations, which can
be enabled for powerpc in the future.
Additionally move powerpc to use generic APIs to locate memory hole for
kexec segments while loading kdump kernel.
This patch (of 7):
kexec_elf_load() loads an ELF executable and sets the address of the
lowest PT_LOAD section to the address held by the lowest_load_addr
function argument.
To determine the lowest PT_LOAD address, a local variable lowest_addr
(type unsigned long) is initialized to UINT_MAX. After loading each
PT_LOAD, its address is compared to lowest_addr. If a loaded PT_LOAD
address is lower, lowest_addr is updated. However, setting lowest_addr to
UINT_MAX won't work when the kernel image is loaded above 4G, as the
returned lowest PT_LOAD address would be invalid. This is resolved by
initializing lowest_addr to ULONG_MAX instead.
This issue was discovered while implementing crashkernel high/low
reservation on the PowerPC architecture.
Link: https://lkml.kernel.org/r/20250131113830.925179-1-sourabhjain@linux.ibm.com Link: https://lkml.kernel.org/r/20250131113830.925179-2-sourabhjain@linux.ibm.com Fixes: a0458284f062 ("powerpc: Add support code for kexec_file_load()") Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com> Acked-by: Hari Bathini <hbathini@linux.ibm.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Madhavan Srinivasan <maddy@linux.ibm.com> Cc: Mahesh Salgaonkar <mahesh@linux.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
No need to specify the array size, let the compiler figure that out.
This addresses this compiler warning that was noticed while build
testing on fedora rawhide:
31 15.81 fedora:rawhide : FAIL gcc version 15.0.1 20250225 (Red Hat 15.0.1-0) (GCC)
util/units.c: In function 'unit_number__scnprintf':
util/units.c:67:24: error: initializer-string for array of 'char' is too long [-Werror=unterminated-string-initialization]
67 | char unit[4] = "BKMG";
| ^~~~~~
cc1: all warnings being treated as errors
If a match was not found, then the write_raw() callback would return
the odr index, not an error. Return -EINVAL if this occurs.
To avoid similar issues in future, introduce j, a new indexing variable
rather than using ret for this purpose.
Fixes: 79de2ee469aa ("iio: accel: mma8452: claim direct mode during write raw") Reviewed-by: David Lechner <dlechner@baylibre.com> Link: https://patch.msgid.link/20250217140135.896574-2-jic23@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to record a trace on kernel with 64k pages resulted in -ENOMEM.
This happens due to a bug in calculating the number of table pages, which
returns zero. Fix the issue by rounding up.
$ perf record --kcore -e cs_etm/@tmc_etr55,cycacc,branch_broadcast/k --per-thread taskset --cpu-list 1 dd if=/dev/zero of=/dev/null
failed to mmap with 12 (Cannot allocate memory)
Fixes: 8ed536b1e283 ("coresight: catu: Add support for scatter gather tables") Signed-off-by: Ilkka Koskinen <ilkka@os.amperecomputing.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20250109215348.5483-1-ilkka@os.amperecomputing.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In do_isofs_readdir() when assigning the variable
"struct iso_directory_record *de" the b_data field of the buffer_head
is accessed and an offset is added to it, the size of b_data is 2048
and the offset size is 2047, meaning
"de = (struct iso_directory_record *) (bh->b_data + offset);"
yields the final byte of the 2048 sized b_data block.
The first byte of the directory record (de_len) is then read and
found to be 31, meaning the directory record size is 31 bytes long.
The directory record is defined by the structure:
The fixed portion of this structure occupies 33 bytes. Therefore, a
valid directory record must be at least 33 bytes long
(even without considering the variable-length name field).
Since de_len is only 31, it is insufficient to contain
the complete fixed header.
The code later hits the following sanity check that
compares de_len against the sum of de->name_len and
sizeof(struct iso_directory_record):
if (de_len < de->name_len[0] + sizeof(struct iso_directory_record)) {
...
}
Since the fixed portion of the structure is
33 bytes (up to and including name_len member),
a valid record should have de_len of at least 33 bytes;
here, however, de_len is too short, and the field de->name_len
(located at offset 32) is accessed even though it lies beyond
the available 31 bytes.
This access on the corrupted isofs data triggers a KASAN uninitialized
memory warning. The fix would be to first verify that de_len is at least
sizeof(struct iso_directory_record) before accessing any
fields like de->name_len.
Reported-by: syzbot <syzbot+812641c6c3d7586a1613@syzkaller.appspotmail.com> Tested-by: syzbot <syzbot+812641c6c3d7586a1613@syzkaller.appspotmail.com> Closes: https://syzkaller.appspot.com/bug?extid=812641c6c3d7586a1613 Fixes: 2deb1acc653c ("isofs: fix access to unallocated memory when reading corrupted filesystem") Signed-off-by: Qasim Ijaz <qasdev00@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://patch.msgid.link/20250211195900.42406-1-qasdev00@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the HMAC RFC, the authentication key
can be 0 bytes, and the hardware can handle this
scenario. Therefore, remove the incorrect validation
for this case.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2") Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com> Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
2e4be0d011f2 ("x86/show_trace_log_lvl: Ensure stack pointer is aligned, again")
was intended to ensure alignment of the stack pointer; but it also moved
the initialization of the "stack" variable down into the loop header.
This was likely intended as a no-op cleanup, since the commit
message does not mention it; however, this caused a behavioral change
because the value of "regs" is different between the two places.
Originally, get_stack_pointer() used the regs provided by the caller; after
that commit, get_stack_pointer() instead uses the regs at the top of the
stack frame the unwinder is looking at. Often, there are no such regs at
all, and "regs" is NULL, causing get_stack_pointer() to fall back to the
task's current stack pointer, which is not what we want here, but probably
happens to mostly work. Other times, the original regs will point to
another regs frame - in that case, the linear guess unwind logic in
show_trace_log_lvl() will start unwinding too far up the stack, causing the
first frame found by the proper unwinder to never be visited, resulting in
a stack trace consisting purely of guess lines.
Fix it by moving the "stack = " assignment back where it belongs.
If offset end up being high enough, right hand expression in functions
like sm501_gpio_set() shifted left for that number of bits, may
not fit in int type.
Just in case, fix that by using BIT() both as an option safe from
overflow issues and to make this step look similar to other gpio
drivers.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
When cur_qp isn't NULL, in order to avoid fetching the QP from
the radix tree again we check if the next cqe QP is identical to
the one we already have.
The bug however is that we are checking if the QP is identical by
checking the QP number inside the CQE against the QP number inside the
mlx5_ib_qp, but that's wrong since the QP number from the CQE is from
FW so it should be matched against mlx5_core_qp which is our FW QP
number.
Otherwise we could use the wrong QP when handling a CQE which could
cause the kernel trace below.
This issue is mainly noticeable over QPs 0 & 1, since for now they are
the only QPs in our driver whereas the QP number inside mlx5_ib_qp
doesn't match the QP number inside mlx5_core_qp.
The charge input threshold voltage register on the MAX77693 PMIC accepts
four values: 0x0 for 4.3v, 0x1 for 4.7v, 0x2 for 4.8v and 0x3 for 4.9v.
Due to an oversight, the driver calculated the values for 4.7v and above
starting from 0x0, rather than from 0x1 ([(4700000 - 4700000) / 100000]
gives 0).
Add 1 to the calculation to ensure that 4.7v is converted to a register
value of 0x1 and that the other two voltages are converted correctly as
well.
Fixes: 87c2d9067893 ("power: max77693: Add charger driver for Maxim 77693") Signed-off-by: Artur Weber <aweber.kernel@gmail.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20250316-max77693-charger-input-threshold-fix-v1-1-2b037d0ac722@gmail.com Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
PUSH_REGS with save_ret=1 is used by interrupt entry helper functions that
initially start with a UNWIND_HINT_FUNC ORC state.
However, save_ret=1 means that we clobber the helper function's return
address (and then later restore the return address further down on the
stack); after that point, the only thing on the stack we can unwind through
is the IRET frame, so use UNWIND_HINT_IRET_REGS until we have a full
pt_regs frame.
( An alternate approach would be to move the pt_regs->di overwrite down
such that it is the final step of pt_regs setup; but I don't want to
rearrange entry code just to make unwinding a tiny bit more elegant. )
Fixes: 9e809d15d6b6 ("x86/entry: Reduce the code footprint of the 'idtentry' macro") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Brian Gerst <brgerst@gmail.com> Cc: Juergen Gross <jgross@suse.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Kees Cook <keescook@chromium.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Link: https://lore.kernel.org/r/20250325-2025-03-unwind-fixes-v1-1-acd774364768@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The bit index of the peripheral clock for mmc A is wrong
This was probably not a problem for mmc A as the peripheral is likely left
enabled by the bootloader.
No issues has been reported so far but it could be a problem, most likely
some form of conflict between the ethernet and mmc A clock, breaking
ethernet on init.
Use the value provided by the documentation for mmc A before this
becomes an actual problem.
The 32k clock reference a parent 'cts_slow_oscin' with a fixme note saying
that this clock should be provided by AO controller.
The HW probably has this clock but it does not exist at the moment in
any controller implementation. Furthermore, referencing clock by the global
name should be avoided whenever possible.
There is no reason to keep this hack around, at least for now.
Several clocks used by both g12a and g12b use the g12a cpu A clock hw
pointer as clock parent. This is incorrect on g12b since the parents of
cluster A cpu clock are different. Also the hw clock provided as parent to
these children is not even registered clock on g12b.
Fix the problem by reverting to the global namespace and let CCF pick
the appropriate, as it is already done for other clocks, such as
cpu_clk_trace_div.
Tegra devices have an 'sfsel' bit field that determines whether a pin
operates in SFIO (Special Function I/O) or GPIO mode. Currently,
tegra_pinctrl_gpio_disable_free() sets this bit when releasing a GPIO.
However, tegra_pinctrl_set_mux() can be called independently in certain
code paths where gpio_disable_free() is not invoked. In such cases, failing
to set the SFIO mode could lead to incorrect pin configurations, resulting
in functional issues for peripherals relying on SFIO.
This patch ensures that whenever set_mux() is called, the SFIO mode is
correctly set in the Mux Register if the 'sfsel' bit is present. This
prevents situations where the pin remains in GPIO mode despite being
configured for SFIO use.
projects / thirdparty / kernel / stable.git / log
