gcc-11 now warns about a confusingly indented code block:
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
1291 | if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
| ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;
Rewrite this to use a single if() block with the __is_defined() macro.
gcc-11 starts warning about misleading indentation inside of macros:
drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
103 | if (verbose > 1) \
| ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
200 | v2printk("kgdbts: breakpoint complete\n");
| ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
105 | touch_nmi_watchdog(); \
| ^~~~~~~~~~~~~~~~~~
The code looks correct to me, so just reindent it for readability.
gcc-11 with KASAN on 32-bit arm produces a warning about a function
that needs a lot of stack space:
drivers/net/wireless/cisco/airo.c: In function 'setup_card.constprop':
drivers/net/wireless/cisco/airo.c:3960:1: error: the frame size of 1512 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
Most of this is from a single large structure that could be dynamically
allocated or moved into the per-device structure. However, as the callers
all seem to have a fairly well bounded call chain, the easiest change
is to pull out the part of the function that needs the large variables
into a separate function and mark that as noinline_for_stack. This does
not reduce the total stack usage, but it gets rid of the warning and
requires minimal changes otherwise.
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/x86/lib/msr-smp.c:255:51: error: argument 2 of type ‘u32 *’ {aka ‘unsigned int *’} declared as a pointer [-Werror=array-parameter=]
255 | int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
| ~~~~~^~~~
arch/x86/include/asm/msr.h:347:50: note: previously declared as an array ‘u32[8]’ {aka ‘unsigned int[8]’}
When CONFIG_NET_SWITCHDEV is disabled, the shim for switchdev_port_attr_set
inside br_mc_disabled_update returns -EOPNOTSUPP. This is not caught,
and propagated to the caller of br_multicast_add_port, preventing ports
from joining the bridge.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Fixes: ae1ea84b33da ("net: bridge: propagate error code and extack from br_mc_disabled_update") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c705d07d784 ("SoC: rsnd: add interrupt support for SSI BUSIF
buffer") adds __rsnd_ssi_interrupt() checks for BUSIF status,
but is using "break" at for loop.
This means it is not checking all status. Let's check all BUSIF status.
Fixes: commit 66c705d07d784 ("SoC: rsnd: add interrupt support for SSI BUSIF buffer") Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/874kgh1jsw.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call nvme_configure_apst when the controller is not live, given
that nvme_configure_apst will fail due the lack of an admin queue when
the controller is being torn down and nvme_set_latency_tolerance is
called from dev_pm_qos_hide_latency_tolerance.
Fixes: 510a405d945b("nvme: fix memory leak for power latency tolerance") Reported-by: Peng Liu <liupeng17@lenovo.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using no_printk() for jbd_debug() revealed two warnings:
fs/jbd2/recovery.c: In function 'fc_do_one_pass':
fs/jbd2/recovery.c:256:30: error: format '%d' expects a matching 'int' argument [-Werror=format=]
256 | jbd_debug(3, "Processing fast commit blk with seq %d");
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
fs/ext4/fast_commit.c: In function 'ext4_fc_replay_add_range':
fs/ext4/fast_commit.c:1732:30: error: format '%d' expects argument of type 'int', but argument 2 has type 'long unsigned int' [-Werror=format=]
1732 | jbd_debug(1, "Converting from %d to %d %lld",
The first one was added incorrectly, and was also missing a few newlines
in debug output, and the second one happened when the type of an
argument changed.
Reported-by: kernel test robot <lkp@intel.com> Fixes: d556435156b7 ("jbd2: avoid -Wempty-body warnings") Fixes: 6db074618969 ("ext4: use BIT() macro for BH_** state bits") Fixes: 5b849b5f96b4 ("jbd2: fast commit recovery path") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20210409201211.1866633-1-arnd@kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-add the compatible value for R-Car H1, which was lost during the
json-schema conversion. Make the "resets" property optional on R-Car
H1, as it is not present yet on R-Car Gen1 SoCs.
The commit 724fabf5df13 ("dt-bindings: phy: qcom,qmp-usb3-dp: Add DP phy
information") has support for DP part of USB3+DP combo PHYs. However
this change is not backwards compatible, placing additional requirements
onto qcom,sc7180-qmp-usb3-phy and qcom,sdm845-qmp-usb3-phy device nodes
(to include separate DP part, etc). However the aforementioned nodes do
not inclue DP part, they strictly follow the schema defined in the
qcom,qmp-phy.yaml file. Move those compatibles, leaving
qcom,qmp-usb3-dp-phy.yaml to describe only real "combo" USB3+DP device nodes.
The serial console is located on the Falcon CPU board. Hence move
serial console configuration from the main Falcon DTS file to the DTS
file that describes the CPU board.
When adding support for V3U (r8a779a0) it was incorrectly recorded it
supports four nodes, while in fact it supports five. The fifth node is
named TSC0 and breaks the existing naming schema starting at 1. Work
around this by separately defining the reg property for V3U and others.
Restore the maximum number of nodes to three for other compatibles as
it was before erroneously increasing it for V3U.
There are some omissions in the previous patch about replacing
I2C_MAX_FAST_MODE__FREQ with I2C_MAX_FAST_MODE_PLUS_FREQ and
need to fix it.
Fixes: b44658e755b5("i2c: mediatek: Send i2c master code at more than 1MHz") Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the power domains names to the power domain struct so we
have meaningful name for every power domain. This also removes the
following debugfs error message.
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749a6 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names") Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The retire logic uses the 2 lower bits of the pointer to the retire
function to store flags. However, the auto_retire function is not
guaranteed to be aligned to a multiple of 4, which causes crashes as
we jump to the wrong address, for example like this:
__i915_active_call annotation is required on the retire callback to ensure
correct function alignment.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: a21ce8ad12d2 ("drm/i915/overlay: Switch to using i915_active tracking") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210429083530.849546-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit d8e44e4dd221ee283ea60a6fb87bca08807aa0ab) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link status is different from display connected status in the case
of something like an Apple dongle where the type-c plug can be
connected, and therefore the link is connected, but no sink is
connected until an HDMI cable is plugged into the dongle.
The sink_count of DPCD of dongle will increase to 1 once an HDMI
cable is plugged into the dongle so that display connected status
will become true. This checking also apply at pm_resume.
Changes in v4:
-- none
Fixes: 94e58e2d06e3 ("drm/msm/dp: reset dp controller only at boot up and pm_resume") Reported-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Link: https://lore.kernel.org/r/1619048258-8717-2-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In gen8_preallocate_top_level_pdp, pde and pde->pt.base are allocated
via alloc_pd(vm) with one reference. If pin_pt_dma() failed, pde->pt.base
is freed by i915_gem_object_put() with a reference dropped. Then free_pd
calls free_px() defined in intel_ppgtt.c, which calls i915_gem_object_put()
to put pde->pt.base again.
As pde->pt.base is protected by refcount, so the second put will not free
pde->pt.base actually. But, maybe it is better to remove the first put?
syzbot can trigger the WARN() in init_uevent_argv() which isn't the
nicest as the code does properly recover and handle the error. So
change the WARN() call to pr_warn() and provide some more information on
what the buffer size that was needed.
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com> Cc: Tero Kristo <kristo@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm timers instead.
Let's prepare for adding support for percpu timers by adding a common
dmtimer_clkevt_init_common() and call it from dmtimer_clockevent_init().
This patch makes no intentional functional changes.
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b4c
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b4c ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.") Reported-by: Huacai Chen <chenhuacai@kernel.org> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable@vger.kernel.org # v2.6.30+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32-bit architectures which expect 8-byte alignment for 8-byte integers and
need 64-bit DMA addresses (arm, mips, ppc) had their struct page
inadvertently expanded in 2019. When the dma_addr_t was added, it forced
the alignment of the union to 8 bytes, which inserted a 4 byte gap between
'flags' and the union.
Fix this by storing the dma_addr_t in one or two adjacent unsigned longs.
This restores the alignment to that of an unsigned long. We always
store the low bits in the first word to prevent the PageTail bit from
being inadvertently set on a big endian platform. If that happened,
get_user_pages_fast() racing against a page which was freed and
reallocated to the page_pool could dereference a bogus compound_head(),
which would be hard to trace back to this cause.
Disable preemption when probing a user return MSR via RDSMR/WRMSR. If
the MSR holds a different value per logical CPU, the WRMSR could corrupt
the host's value if KVM is preempted between the RDMSR and WRMSR, and
then rescheduled on a different CPU.
Opportunistically land the helper in common x86, SVM will use the helper
in a future commit.
Fixes: 4be534102624 ("KVM: VMX: Initialize vmx->guest_msrs[] right after allocation") Cc: stable@vger.kernel.org Cc: Xiaoyao Li <xiaoyao.li@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-6-seanjc@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear KVM's RDPID capability if the ENABLE_RDTSCP secondary exec control is
unsupported. Despite being enumerated in a separate CPUID flag, RDPID is
bundled under the same VMCS control as RDTSCP and will #UD in VMX non-root
if ENABLE_RDTSCP is not enabled.
Fixes: 41cd02c6f7f6 ("kvm: x86: Expose RDPID in KVM_GET_SUPPORTED_CPUID") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-2-seanjc@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Reviewed-by: Reiji Watanabe <reijiw@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enlightened VMCS is in use and nested state is migrated with
vmx_get_nested_state()/vmx_set_nested_state() KVM can't map evmcs
page right away: evmcs gpa is not 'struct kvm_vmx_nested_state_hdr'
and we can't read it from VP assist page because userspace may decide
to restore HV_X64_MSR_VP_ASSIST_PAGE after restoring nested state
(and QEMU, for example, does exactly that). To make sure eVMCS is
mapped /vmx_set_nested_state() raises KVM_REQ_GET_NESTED_STATE_PAGES
request.
Commit f2c7ef3ba955 ("KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES
on nested vmexit") added KVM_REQ_GET_NESTED_STATE_PAGES clearing to
nested_vmx_vmexit() to make sure MSR permission bitmap is not switched
when an immediate exit from L2 to L1 happens right after migration (caused
by a pending event, for example). Unfortunately, in the exact same
situation we still need to have eVMCS mapped so
nested_sync_vmcs12_to_shadow() reflects changes in VMCS12 to eVMCS.
As a band-aid, restore nested_get_evmcs_page() when clearing
KVM_REQ_GET_NESTED_STATE_PAGES in nested_vmx_vmexit(). The 'fix' is far
from being ideal as we can't easily propagate possible failures and even if
we could, this is most likely already too late to do so. The whole
'KVM_REQ_GET_NESTED_STATE_PAGES' idea for mapping eVMCS after migration
seems to be fragile as we diverge too much from the 'native' path when
vmptr loading happens on vmx_set_nested_state().
Allow userspace to enable RDPID for a guest without also enabling RDTSCP.
Aside from checking for RDPID support in the obvious flows, VMX also needs
to set ENABLE_RDTSCP=1 when RDPID is exposed.
For the record, there is no known scenario where enabling RDPID without
RDTSCP is desirable. But, both AMD and Intel architectures allow for the
condition, i.e. this is purely to make KVM more architecturally accurate.
Fixes: 41cd02c6f7f6 ("kvm: x86: Expose RDPID in KVM_GET_SUPPORTED_CPUID") Cc: stable@vger.kernel.org Reported-by: Reiji Watanabe <reijiw@google.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-8-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not advertise emulation support for RDPID if RDTSCP is unsupported.
RDPID emulation subtly relies on MSR_TSC_AUX to exist in hardware, as
both vmx_get_msr() and svm_get_msr() will return an error if the MSR is
unsupported, i.e. ctxt->ops->get_msr() will fail and the emulator will
inject a #UD.
Note, RDPID emulation also relies on RDTSCP being enabled in the guest,
but this is a KVM bug and will eventually be fixed.
Fixes: fb6d4d340e05 ("KVM: x86: emulate RDPID") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-3-seanjc@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Reviewed-by: Reiji Watanabe <reijiw@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d3eeb1d77c5d0af ("xen/gntdev: use mmu_interval_notifier_insert")
introduced an error in gntdev_mmap(): in case the call of
mmu_interval_notifier_insert_locked() fails the exit path should not
call mmu_interval_notifier_remove(), as this might result in NULL
dereferences.
One reason for failure is e.g. a signal pending for the running
process.
RTC drivers used to leave .set_alarm() NULL in order to signal the RTC
device doesn't support alarms. The drivers are now clearing the
RTC_FEATURE_ALARM bit for that purpose in order to keep the rtc_class_ops
structure const. So now, .set_alarm() is set unconditionally and this
possibly causes the alarmtimer code to select an RTC device that doesn't
support alarms.
Test RTC_FEATURE_ALARM instead of relying on ops->set_alarm to determine
whether alarms are available.
We have a cycle of callbacks scheduling works which submit
URBs with those callbacks. This needs to be blocked, stopped
and unblocked to untangle the circle.
The raw temperature value is a 16-bit signed integer. The sign casting
is missing in the code, which results in a wrong temperature reported
by userspace tools, fix it.
Cc: stable@vger.kernel.org Fixes: 3904b28efb2c ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Datasheet: https://www.cdiweb.com/datasheets/invensense/mpu-3000a.pdf Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Asus TF201 Reported-by: Svyatoslav Ryhel <clamor95@gmail.com> Reviewed-by: Andy Shevchenko <Andy.Shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Link: https://lore.kernel.org/r/20210423020959.5023-1-digetx@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ioctl handlers are removed twice. For the first time during
iio_device_unregister() then later on inside
iio_device_unregister_eventset() and iio_buffers_free_sysfs_and_mask().
Double free leads to kernel panic.
Fix this by not touching ioctl handlers list directly but rather
letting code responsible for registration call the matching cleanup
routine itself.
Fixes: 8dedcc3eee3ac ("iio: core: centralize ioctl() calls to the main chardev") Signed-off-by: Tomasz Duszynski <tomasz.duszynski@octakon.com> Acked-by: Alexandru Ardelean <ardeleanalex@gmail.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210423080244.2790-1-tomasz.duszynski@octakon.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9ebf30007858 ("xhci: Fix halted endpoint at stop endpoint command
completion") in 5.12 changes how cancelled URBs are given back.
To cancel a URB xhci driver needs to stop the endpoint first.
To clear a halted endpoint xhci driver needs to reset the endpoint.
In rare cases when an endpoint halt (error) races with a endpoint stop we
need to clear the reset before removing, and giving back the cancelled URB.
The above change in 5.12 takes care of this, but it also relies on the
reset endpoint completion handler to give back the cancelled URBs.
There are cases when driver refuses to queue reset endpoint commands,
for example when a link suddenly goes to an inactive error state.
In this case the cancelled URB is never given back.
Fix this by giving back the URB in the stop endpoint if queuing a reset
endpoint command fails.
In the same way as Intel Tiger Lake TCSS (Type-C Subsystem) the Alder Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
commit 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects
in PD mode") introduced retrieval of the PDOs when connected to a
PD-capable source. But only the first 4 PDOs are received since
that is the maximum number that can be fetched at a time given the
MESSAGE_IN length limitation (16 bytes). However, as per the PD spec
a connected source may advertise up to a maximum of 7 PDOs.
If such a source is connected it's possible the PPM could have
negotiated a power contract with one of the PDOs at index greater
than 4, and would be reflected in the request data object's (RDO)
object position field. This would result in an out-of-bounds access
when the rdo_index() is used to index into the src_pdos array in
ucsi_psy_get_voltage_now().
With the help of the UBSAN -fsanitize=array-bounds checker enabled
this exact issue is revealed when connecting to a PD source adapter
that advertise 5 PDOs and the PPM enters a contract having selected
the 5th one.
We can resolve this by instead retrieving and storing up to the
maximum of 7 PDOs in the con->src_pdos array. This would involve
two calls to the GET_PDOS command.
Fixes: 992a60ed0d5e ("usb: typec: ucsi: register with power_supply class") Fixes: 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects in PD mode") Cc: stable@vger.kernel.org Reported-and-tested-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210503074611.30973-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After receiving Sink Capabilities Message in GET_SINK_CAP AMS, it is
incorrect to call tcpm_pd_handle_state because the Message is expected
and the current state is not Ready states. The result of this incorrect
operation ends in Soft Reset which is definitely wrong. Simply
forwarding to Ready States is enough to finish the AMS.
If an error is received when issuing a start or update transfer
command, the error handler will stop all active requests (including
the current USB request), and call dwc3_gadget_giveback() to notify
function drivers of the requests which have been stopped. Avoid
returning an error for kick transfer during EP queue, to remove
duplicate cleanup operations on the request being queued.
commit 72704f876f50 ("dwc3: gadget: Implement the suspend entry event
handler") introduced (nearly 5 years ago!) an interrupt handler for
U3/L1-L2 suspend events. The problem is that these events aren't
currently enabled in the DEVTEN register so the handler is never
even invoked. Fix this simply by enabling the corresponding bit
in dwc3_gadget_enable_irq() using the same revision check as found
in the handler.
Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler") Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210428090111.3370-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software") Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Phil Elwell <phil@raspberrypi.com> Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.
When extcon is used in combination with dwc3, it is assumed that the dwc3
registers are untouched and as such are only configured if VBUS is valid
or ID is tied to ground.
In case VBUS is not valid or ID is floating, the registers are not
configured as such during driver initialization, causing a wrong
default state during boot.
If the registers are not in a default state, because they are for
instance touched by a boot loader, this can cause for a kernel error.
If a tag set is shared across request queues (e.g. SCSI LUNs) then the
block layer core keeps track of the number of active request queues in
tags->active_queues. blk_mq_tag_busy() and blk_mq_tag_idle() update that
atomic counter if the hctx flag BLK_MQ_F_TAG_QUEUE_SHARED is set. Make
sure that blk_mq_exit_queue() calls blk_mq_tag_idle() before that flag is
cleared by blk_mq_del_queue_tag_set().
Cc: Christoph Hellwig <hch@infradead.org> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Fixes: 0d2602ca30e4 ("blk-mq: improve support for shared tags maps") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210513171529.7977-1-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of shared sbitmap, request won't be held in plug list any more
sine commit 32bc15afed04 ("blk-mq: Facilitate a shared sbitmap per
tagset"), this way makes request merge from flush plug list & batching
submission not possible, so cause performance regression.
Yanhui reports performance regression when running sequential IO
test(libaio, 16 jobs, 8 depth for each job) in VM, and the VM disk
is emulated with image stored on xfs/megaraid_sas.
Fix the issue by recovering original behavior to allow to hold request
in plug list.
Cc: Yanhui Ma <yama@redhat.com> Cc: John Garry <john.garry@huawei.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: kashyap.desai@broadcom.com Fixes: 32bc15afed04 ("blk-mq: Facilitate a shared sbitmap per tagset") Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210514022052.1047665-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
scv support introduced the notion of code that implicitly soft-masks
irqs due to the instruction addresses. This is required because scv
enters the kernel with MSR[EE]=1.
If a NMI (including soft-NMI) interrupt hits when we are implicitly
soft-masked then its regs->softe does not reflect this because it is
derived from the explicit soft mask state (paca->irq_soft_mask). This
makes arch_irq_disabled_regs(regs) return false.
This can trigger a warning in the soft-NMI watchdog code (shown below).
Fix it by having NMI interrupts set regs->softe to disabled in case of
interrupting an implicit soft-masked region.
Open /dev/nbdX first, the config_refs will be 1 and
the pointers in nbd_device are still null. Disconnect
/dev/nbdX, then reference a null recv_workq. The
protection by config_refs in nbd_genl_disconnect is useless.
To fix it, just add if (nbd->recv_workq) to nbd_disconnect_and_put().
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs") Signed-off-by: Sun Ke <sunke32@huawei.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Link: https://lore.kernel.org/r/20210512114331.1233964-2-sunke32@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
in select_idle_cpu(), we check if an idle core is present in the LLC
of the target CPU via the flag "has_idle_cores". We look for the idle
core in select_idle_cores(). If select_idle_cores() isn't able to find
an idle core/CPU, we need to unset the has_idle_cores flag in the LLC
of the target to prevent other CPUs from going down this route.
However, the current code is unsetting it in the LLC of the current
CPU instead of the target CPU. This patch fixes this issue.
In f2fs_destroy_compress_ctx(), after f2fs_destroy_compress_ctx(),
cc.cluster_idx will be cleared w/ NULL_CLUSTER, f2fs_cluster_blocks()
may check wrong cluster metadata, fix it.
Fixes: 4c8ff7095bef ("f2fs: support data compression") Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is truncate() may race with overwrite as below,
so that one reference count left in page can not guarantee the
page attaching in mapping tree all the time, after truncation,
later find_lock_page() may return NULL pointer.
When running some traffic and taking down the link on peer, a
retry counter exceeded error is received. This leads to
nvmet_rdma_error_comp which tried accessing the cq_context to
obtain the queue. The cq_context is no longer valid after the
fix to use shared CQ mechanism and should be obtained similar
to how it is obtained in other functions from the wc->qp.
When handling passthru commands, for inline bio allocation we only
consider the transfer size. This works well when req->sg_cnt fits into
the req->inline_bvec, but it will result in the early return from
bio_add_hw_page() when req->sg_cnt > NVMET_MAX_INLINE_BVEC.
Consider an I/O of size 32768 and first buffer is not aligned to the
page boundary, then I/O is split in following manner :-
Now the req->transfer_size == NVMET_MAX_INLINE_DATA_LEN i.e. 32768, but
the req->sg_cnt is (9) > NVMET_MAX_INLINE_BIOVEC which is (8).
This will result in early return in the following code path :-
nvmet_bdev_execute_rw()
bio_add_pc_page()
bio_add_hw_page()
if (bio_full(bio, len))
return 0;
Use previously introduced helper nvmet_use_inline_bvec() to consider
req->sg_cnt when using inline bio. This only affects nvme-loop
transport.
Fixes: dab3902b19a0 ("nvmet: use inline bio for passthru fast path") Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When handling rw commands, for inline bio case we only consider
transfer size. This works well when req->sg_cnt fits into the
req->inline_bvec, but it will result in the warning in
__bio_add_page() when req->sg_cnt > NVMET_MAX_INLINE_BVEC.
Consider an I/O size 32768 and first page is not aligned to the page
boundary, then I/O is split in following manner :-
Now the req->transfer_size == NVMET_MAX_INLINE_DATA_LEN i.e. 32768, but
the req->sg_cnt is (9) > NVMET_MAX_INLINE_BIOVEC which is (8).
This will result in the following warning message :-
This scenario is very hard to reproduce on the nvme-loop transport only
with rw commands issued with the passthru IOCTL interface from the host
application and the data buffer is allocated with the malloc() and not
the posix_memalign().
__blk_mq_sched_bio_merge() gets the ctx and hctx for the current CPU and
passes the hctx to ->bio_merge(). kyber_bio_merge() then gets the ctx
for the current CPU again and uses that to get the corresponding Kyber
context in the passed hctx. However, the thread may be preempted between
the two calls to blk_mq_get_ctx(), and the ctx returned the second time
may no longer correspond to the passed hctx. This "works" accidentally
most of the time, but it can cause us to read garbage if the second ctx
came from an hctx with more ctx's than the first one (i.e., if
ctx->index_hw[hctx->type] > hctx->nr_ctx).
This manifested as this UBSAN array index out of bounds error reported
by Jakub:
UBSAN: array-index-out-of-bounds in ../kernel/locking/qspinlock.c:130:9
index 13106 is out of range for type 'long unsigned int [128]'
Call Trace:
dump_stack+0xa4/0xe5
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold.13+0x2a/0x34
queued_spin_lock_slowpath+0x476/0x480
do_raw_spin_lock+0x1c2/0x1d0
kyber_bio_merge+0x112/0x180
blk_mq_submit_bio+0x1f5/0x1100
submit_bio_noacct+0x7b0/0x870
submit_bio+0xc2/0x3a0
btrfs_map_bio+0x4f0/0x9d0
btrfs_submit_data_bio+0x24e/0x310
submit_one_bio+0x7f/0xb0
submit_extent_page+0xc4/0x440
__extent_writepage_io+0x2b8/0x5e0
__extent_writepage+0x28d/0x6e0
extent_write_cache_pages+0x4d7/0x7a0
extent_writepages+0xa2/0x110
do_writepages+0x8f/0x180
__writeback_single_inode+0x99/0x7f0
writeback_sb_inodes+0x34e/0x790
__writeback_inodes_wb+0x9e/0x120
wb_writeback+0x4d2/0x660
wb_workfn+0x64d/0xa10
process_one_work+0x53a/0xa80
worker_thread+0x69/0x5b0
kthread+0x20b/0x240
ret_from_fork+0x1f/0x30
Only Kyber uses the hctx, so fix it by passing the request_queue to
->bio_merge() instead. BFQ and mq-deadline just use that, and Kyber can
map the queues itself to avoid the mismatch.
If 'acpi_device_set_name()' fails, we must free
'acpi_device_bus_id->bus_id' or there is a (potential) memory leak.
Fixes: eb50aaf960e3 ("ACPI: scan: Use unique number for instance_no") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Not_Supported Message is acceptable in VDM AMS. Redirect the VDM state
machine to VDM_STATE_DONE when receiving Not_Supported and finish the
VDM AMS.
Also, after the loop in vdm_state_machine_work, add more conditions of
VDM states to clear the vdm_sm_running flag because those are all
stopping states when leaving the loop.
In addition, finish the VDM AMS if the port partner responds BUSY.
The poll rate limiter time was initialized at zero. This breaks the
comparison in time_after if jiffies is large. Switch to storing the
next update time rather than the previous time, and initialize the
time when the device is probed.
Fixes: c10e753d43eb ("hwmon (occ): Add sensor types and versions") Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20210429151336.18980-1-eajames@linux.ibm.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error
message. Moreover, another error message is printed at the end of the
error handling path. The corresponding error code (-ENOMEM) is more
informative.
So remove simplify the first error message.
While at it, also remove the useless initialization of 'retval'.
When the ioctl() mechanism was introduced in IIO core to centralize the
registration of all ioctls in one place via commit 8dedcc3eee3ac ("iio:
core: centralize ioctl() calls to the main chardev"), the return code was
changed from ENODEV to EINVAL, when the ioctl code isn't known.
This was done by accident.
This change reverts back to the old behavior, where if the ioctl() code
isn't known, ENODEV is returned (vs EINVAL).
This was brought into perspective by this patch:
https://lore.kernel.org/linux-iio/20210428150815.136150-1-paul@crapouillou.net/
Fixes: 8dedcc3eee3ac ("iio: core: centralize ioctl() calls to the main chardev") Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Tested-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During commit 067fda1c065ff ("iio: hid-sensors: move triggered buffer
setup into hid_sensor_setup_trigger"), the
iio_triggered_buffer_{setup,cleanup}() functions got moved under the
hid-sensor-trigger module.
The above change works fine, if any of the sensors get built. However, when
only the common hid-sensor-trigger module gets built (and none of the
drivers), then the IIO_TRIGGERED_BUFFER symbol isn't selected/enforced.
Previously, each driver would enforce/select the IIO_TRIGGERED_BUFFER
symbol. With this change the HID_SENSOR_IIO_TRIGGER (for the
hid-sensor-trigger module) will enforce that IIO_TRIGGERED_BUFFER gets
selected.
All HID sensor drivers select the HID_SENSOR_IIO_TRIGGER symbol. So, this
change removes the IIO_TRIGGERED_BUFFER enforcement from each driver.
Fixes: 067fda1c065ff ("iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger") Reported-by: Thomas Deutschmann <whissi@gentoo.org> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://lore.kernel.org/r/20210414084955.260117-1-aardelean@deviqon.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When devm_request_threaded_irq() fails, we should decrease the
runtime PM counter to keep the counter balanced. But when
iio_device_register() fails, we need not to decrease it because
we have already decreased it before.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Fixes: 97d642e23037 ("iio: light: Add a driver for Sharp GP2AP002x00F") Link: https://lore.kernel.org/r/20210407034927.16882-1-dinghao.liu@zju.edu.cn Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As part of commit e81a7018d93a ("usb: dwc3: allocate gadget structure
dynamically") the dwc3_gadget_release() was added which will free
the dwc->gadget structure upon the device's removal when
usb_del_gadget_udc() is called in dwc3_gadget_exit().
However, simply freeing the gadget results a dangling pointer
situation: the endpoints created in dwc3_gadget_init_endpoints()
have their dep->endpoint.ep_list members chained off the list_head
anchored at dwc->gadget->ep_list. Thus when dwc->gadget is freed,
the first dwc3_ep in the list now has a dangling prev pointer and
likewise for the next pointer of the dwc3_ep at the tail of the list.
The dwc3_gadget_free_endpoints() that follows will result in a
use-after-free when it calls list_del().
This was caught by enabling KASAN and performing a driver unbind.
The recent commit 568262bf5492 ("usb: dwc3: core: Add shutdown
callback for dwc3") also exposes this as a panic during shutdown.
There are a few possibilities to fix this. One could be to perform
a list_del() of the gadget->ep_list itself which removes it from
the rest of the dwc3_ep chain.
Another approach is what this patch does, by splitting up the
usb_del_gadget_udc() call into its separate "del" and "put"
components. This allows dwc3_gadget_free_endpoints() to be
called before the gadget is finally freed with usb_put_gadget().
Fixes: eee19501926d ("perf tools: Grab a copy of libbpf's hashmap") Reported-by: Justin M. Forbes <jforbes@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210508205020.617984-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I am seeing missed wakeups which ultimately lead to a deadlock when I am
using virtiofs with DAX enabled and running "make -j". I had to mount
virtiofs as rootfs and also reduce to dax window size to 256M to reproduce
the problem consistently.
So here is the problem. put_unlocked_entry() wakes up waiters only
if entry is not null as well as !dax_is_conflict(entry). But if I
call multiple instances of invalidate_inode_pages2() in parallel,
then I can run into a situation where there are waiters on
this index but nobody will wake these waiters.
Say a fault in in progress and it has locked entry at offset say "0x1c".
Now say three instances of invalidate_inode_pages2() are in progress
(A, B, C) and they all try to invalidate entry at offset "0x1c". Given
dax entry is locked, all tree instances A, B, C will wait in wait queue.
When dax fault finishes, say A is woken up. It will store NULL entry
at index "0x1c" and wake up B. When B comes along it will find "entry=0"
at page offset 0x1c and it will call put_unlocked_entry(&xas, 0). And
this means put_unlocked_entry() will not wake up next waiter, given
the current code. And that means C continues to wait and is not woken
up.
This patch fixes the issue by waking up all waiters when a dax entry
has been invalidated. This seems to fix the deadlock I am facing
and I can make forward progress.
Reported-by: Sergio Lopez <slp@redhat.com> Fixes: ac401cc78242 ("dax: New fault locking") Reviewed-by: Jan Kara <jack@suse.cz> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20210428190314.1865312-4-vgoyal@redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As of now put_unlocked_entry() always wakes up next waiter. In next
patches we want to wake up all waiters at one callsite. Hence, add a
parameter to the function.
This patch does not introduce any change of behavior.
Reviewed-by: Greg Kurz <groug@kaod.org> Reviewed-by: Jan Kara <jack@suse.cz> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20210428190314.1865312-3-vgoyal@redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan mentioned that he is not very fond of passing around a boolean true/false
to specify if only next waiter should be woken up or all waiters should be
woken up. He instead prefers that we introduce an enum and make it very
explicity at the callsite itself. Easier to read code.
This patch should not introduce any change of behavior.
Reviewed-by: Greg Kurz <groug@kaod.org> Reviewed-by: Jan Kara <jack@suse.cz> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20210428190314.1865312-2-vgoyal@redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an SEV-ES guest is running, the GHCB is unmapped as part of the
vCPU run support. However, kvm_vcpu_unmap() triggers an RCU dereference
warning with CONFIG_PROVE_LOCKING=y because the SRCU lock is released
before invoking the vCPU run support.
Move the GHCB unmapping into the prepare_guest_switch callback, which is
invoked while still holding the SRCU lock, eliminating the RCU dereference
warning.
Fixes: 291bd20d5d88 ("KVM: SVM: Add initial support for a VMGEXIT VMEXIT") Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <b2f9b79d15166f2c3e4375c0d9bc3268b7696455.1620332081.git.thomas.lendacky@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize audio_comp when audio starts and wait for audio_comp at
dp_display_disable(). This will take care of both dongle unplugged
and display off (suspend) cases.
Changes in v2:
-- add dp_display_signal_audio_start()
Changes in v3:
-- restore dp_display_handle_plugged_change() at dp_hpd_unplug_handle().
Changes in v4:
-- none
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Fixes: c703d5789590 ("drm/msm/dp: trigger unplug event in msm_dp_display_disable") Link: https://lore.kernel.org/r/1619048258-8717-3-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit ee66e453db13d (KVM: lapic: Busy wait for timer to expire when
using hv_timer) tries to set ktime->expired_tscdeadline by checking
ktime->hv_timer_in_use since lapic timer oneshot/periodic modes which
are emulated by vmx preemption timer also get advanced, they leverage
the same vmx preemption timer logic with tsc-deadline mode. However,
ktime->hv_timer_in_use is cleared before apic_timer_expired() handling,
let's delay this clearing in preemption-disabled region.
Fixes: ee66e453db13d ("KVM: lapic: Busy wait for timer to expire when using hv_timer") Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1619608082-4187-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
mmu500 targets don't have a "cx_mem" region, set llc_mmio to NULL in that
case to avoid the IS_ERR() condition in a6xx_llc_activate().
Fixes: 3d247123b5a1 ("drm/msm/a6xx: Add support for using system cache on MMU500 based targets") Signed-off-by: Jonathan Marek <jonathan@marek.ca> Link: https://lore.kernel.org/r/20210424014927.1661-1-jonathan@marek.ca Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
single_task_running() is usually more general than need_resched()
but CFS_BANDWIDTH throttling will use resched_task() when there
is just one task to get the task to block. This was causing
long-need_resched warnings and was likely allowing VMs to
overrun their quota when halt polling.
Signed-off-by: Ben Segall <bsegall@google.com> Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-Id: <20210429162233.116849-1-venkateshs@chromium.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Screen flickers on Innolux eDP 1.3 panel when clock rate 540000 is in use.
According to the panel vendor, though clock rate 540000 is advertised,
but the max clock rate it really supports is 270000.
Ville Syrjälä mentioned that fast and narrow also breaks some eDP 1.4
panel, so use slow and wide training for all panels to resolve the
issue.
User also confirmed that the new strategy doesn't introduce any
regression on XPS 9380.
v2:
- Use slow and wide for everything.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3384
References: https://gitlab.freedesktop.org/drm/intel/-/issues/272 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210421052054.1434718-1-kai.heng.feng@canonical.com
(cherry picked from commit acca7762eb71bc05a8f28d29320d193150051f79) Fixes: 2bbd6dba84d4 ("drm/i915: Try to use fast+narrow link on eDP again and fall back to the old max strategy on failure") Cc: <stable@vger.kernel.org> # v5.12+ Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gen2 tiles are 2KiB in size so i915_gem_object_get_tile_row_size()
can in fact return <4KiB, which leads to div-by-zero here.
Avoid that.
Not sure i915_gem_object_get_tile_row_size() is entirely
sane anyway since it doesn't account for the different tile
layouts on i8xx/i915...
I'm not able to hit this before commit 6846895fde05 ("drm/i915:
Replace PIN_NONFAULT with calls to PIN_NOEVICT") and it looks
like I also need to run recent version of Mesa. With those in
place xonotic trips on this quite easily on my 85x.
projects / thirdparty / kernel / stable.git / log
