There is an issue with xfs's error reporting in some cases of I/O partially
failing and partially succeeding. Calls like fsync() can report success even
though not all I/O was successful in partial-failure cases such as one disk of
a RAID0 array being offline.
The issue can occur when there are more than one bio per xfs_ioend struct.
Each call to xfs_end_bio() for a bio completing will write a value to
ioend->io_error. If a successful bio completes after any failed bio, no
error is reported do to it writing 0 over the error code set by any failed bio.
The I/O error information is now lost and when the ioend is completed
only success is reported back up the filesystem stack.
xfs_end_bio() should only set ioend->io_error in the case of BIO_UPTODATE
being clear. ioend->io_error is initialized to 0 at allocation so only needs
to be updated by a failed bio. Also check that ioend->io_error is 0 so that
the first error reported will be the error code returned.
Signed-off-by: David Jeffery <djeffery@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When a task calls execve(), its FP/SIMD state is flushed so that
none of the original program state is observeable by the incoming
program.
However, since this flushing consists of setting the in-memory copy
of the FP/SIMD state to all zeroes, the CPU field is set to CPU 0 as
well, which indicates to the lazy FP/SIMD preserve/restore code that
the FP/SIMD state does not need to be reread from memory if the task
is scheduled again on CPU 0 without any other tasks having entered
userland (or used the FP/SIMD in kernel mode) on the same CPU in the
mean time. If this happens, the FP/SIMD state of the old program will
still be present in the registers when the new program starts.
So set the CPU field to the invalid value of NR_CPUS when performing
the flush, by calling fpsimd_flush_task_state().
Reported-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com> Reported-by: Janet Liu <janet.liu@spreadtrum.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The unregister path of platform_device is broken. On registration, it
will register all resources with either a parent already set, or
type==IORESOURCE_{IO,MEM}. However, on unregister it will release
everything with type==IORESOURCE_{IO,MEM}, but ignore the others. There
are also cases where resources don't get registered in the first place,
like with devices created by of_platform_populate()*.
Fix the unregister path to be symmetrical with the register path by
checking the parent pointer instead of the type field to decide which
resources to unregister. This is safe because the upshot of the
registration path algorithm is that registered resources have a parent
pointer, and non-registered resources do not.
* It can be argued that of_platform_populate() should be registering
it's resources, and they argument has some merit. However, there are
quite a few platforms that end up broken if we try to do that due to
overlapping resources in the device tree. Until that is fixed, we need
to solve the immediate problem.
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Rob Herring <robh@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Grant Likely <grant.likely@linaro.org> Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
If the internal call to of_address_to_resource() fails, we end up
looping forever in of_find_matching_node_by_address(). This can be
caused by a defective device tree, or calling with an incorrect
matches argument.
Fix by calling of_find_matching_node() unconditionally at the end of
the loop.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
During the various CPU_ONLINE callbacks CPUn is online but not
active. Several things can go wrong at that point, depending on
the scheduling of tasks on CPU0.
The ->wake_cpu of the unparked thread is not allowed, making a call
to select_fallback_rq() necessary. Then, select_fallback_rq() cannot
find an allowed, active CPU and promptly resets the allowed CPUs, so
that the task in question ends up on CPU0.
When those unparked tasks are eventually executed, they run
immediately into a BUG:
kernel BUG at kernel/smpboot.c:135!
Just changing the order in which the online/active bits are set
(and adding some memory barriers), would solve the two issues
above. However, it would change the order of operations back to
the one before commit 6acbfb96976f ("sched: Fix hotplug vs.
set_cpus_allowed_ptr()"), thus, reintroducing that particular
problem.
Going further back into history, we have at least the following
commits touching this topic:
- commit 2baab4e90495 ("sched: Fix select_fallback_rq() vs cpu_active/cpu_online")
- commit 5fbd036b552f ("sched: Cleanup cpu_active madness")
Together, these give us the following non-working solutions:
- secondary CPU sets active before online, because active is assumed to
be a subset of online;
- secondary CPU sets online before active, because the primary CPU
assumes that an online CPU is also active;
- secondary CPU sets online and waits for primary CPU to set active,
because it might deadlock.
Commit 875ebe940d77 ("powerpc/smp: Wait until secondaries are
active & online") introduces an arch-specific solution to this
arch-independent problem.
Now, go for a more general solution without explicit waiting and
simply set active twice: once on the secondary CPU after online
was set and once on the primary CPU after online was seen.
set_cpus_allowed_ptr()")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Anton Blanchard <anton@samba.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Joerg Roedel <jroedel@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Wilson <msw@amazon.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 6acbfb96976f ("sched: Fix hotplug vs. set_cpus_allowed_ptr()") Link: http://lkml.kernel.org/r/1439408156-18840-1-git-send-email-jschoenh@amazon.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Users have occasionally reported that file type for some directory
entries is wrong. This mostly happened after updating libraries some
libraries. After some debugging the problem was traced down to
xfs_dir2_node_replace(). The function uses args->filetype as a file type
to store in the replaced directory entry however it also calls
xfs_da3_node_lookup_int() which will store file type of the current
directory entry in args->filetype. Thus we fail to change file type of a
directory entry to a proper type.
Fix the problem by storing new file type in a local variable before
calling xfs_da3_node_lookup_int().
Reported-by: Giacomo Comes <comes@naic.edu> Signed-off-by: Jan Kara <jack@suse.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16:
- file rename: fs/xfs/libxfs/xfs_dir2_node.c -> fs/xfs/xfs_dir2_node.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Most of the time this isn't an issue since hotplugging an adaptor will
trigger a crtc mode change which in turn, causes the driver to probe
every DisplayPort for a dpcd. However, in cases where hotplugging
doesn't cause a mode change (specifically when one unplugs a monitor
from a DisplayPort connector, then plugs that same monitor back in
seconds later on the same port without any other monitors connected), we
never probe for the dpcd before starting the initial link training. What
happens from there looks like this:
- GPU has only one monitor connected. It's connected via
DisplayPort, and does not go through an adaptor of any sort.
- User unplugs DisplayPort connector from GPU.
- Change in HPD is detected by the driver, we probe every
DisplayPort for a possible connection.
- Probe the port the user originally had the monitor connected
on for it's dpcd. This fails, and we clear the first (and only
the first) byte of the dpcd to indicate we no longer have a
dpcd for this port.
- User plugs the previously disconnected monitor back into the
same DisplayPort.
- radeon_connector_hotplug() is called before everyone else,
and tries to handle the link training. Since only the first
byte of the dpcd is zeroed, the driver is able to complete
link training but does so against the wrong dpcd, causing it
to initialize the link with the wrong settings.
- Display stays blank (usually), dpcd is probed after the
initial link training, and the driver prints no obvious
messages to the log.
In theory, since only one byte of the dpcd is chopped off (specifically,
the byte that contains the revision information for DisplayPort), it's
not entirely impossible that this bug may not show on certain monitors.
For instance, the only reason this bug was visible on my ASUS PB238
monitor was due to the fact that this monitor using the enhanced framing
symbol sequence, the flag for which is ignored if the radeon driver
thinks that the DisplayPort version is below 1.1.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since v3.18, attempts to deliver IRQ0 are rejected, breaking orion5x.
Fix this by increasing all interrupts by one, as did 5d6bed2a9c8b for
dove. Also, force MULTI_IRQ_HANDLER for all orion platforms (including
dove) as the specific handler is needed to shift back IRQ numbers by
one.
[gregory.clement@free-electrons.com]: moved the select
MULTI_IRQ_HANDLER from PLAT_ORION_LEGACY to ARCH_ORION5X as it broke
the build for dove.
Fixes: a71b092a9c68 ("ARM: Convert handle_IRQ to use __handle_domain_irq") Signed-off-by: Benjamin Cama <benoar@dolka.fr> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Detlef Vollmann <dv@vollmann.ch> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
While we are committing a transaction, it's possible the previous one is
still finishing its commit and therefore we wait for it to finish first.
However we were not checking if that previous transaction ended up getting
aborted after we waited for it to commit, so we ended up committing the
current transaction which can lead to fs corruption because the new
superblock can point to trees that have had one or more nodes/leafs that
were never durably persisted.
The following sequence diagram exemplifies how this is possible:
btrfs_write_and_wait_transaction() continues
writing ebs
--> fails writing eb X, we abort transaction N
and set bit BTRFS_FS_STATE_ERROR on
fs_info->fs_state, so no new transactions
can start after setting that bit
cleanup_transaction()
btrfs_cleanup_one_transaction()
wakes up task at CPU 1
continues, doesn't abort because
cur_trans->aborted (transaction N + 1)
is zero, and no checks for bit
BTRFS_FS_STATE_ERROR in fs_info->fs_state
are made
btrfs_write_and_wait_transaction(trans, root);
--> succeeds, no errors during writeback
write_ctree_super(trans, root, 0);
--> succeeds
--> we have now a superblock that points us
to some root that uses eb X, which was
never written to disk
In this scenario future attempts to read eb X from disk results in an
error message like "parent transid verify failed on X wanted Y found Z".
So fix this by aborting the current transaction if after waiting for the
previous transaction we verify that it was aborted.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
struct xfs_attr_leafblock contains 'entries' array which is declared
with size 1 altough it can in fact contain much more entries. Since this
array is followed by further struct members, gcc (at least in version
4.8.3) thinks that the array has the fixed size of 1 element and thus
may optimize away all accesses beyond the end of array resulting in
non-working code. This problem was only observed with userspace code in
xfsprogs, however it's better to be safe in kernel as well and have
matching kernel and xfsprogs definitions.
Signed-off-by: Jan Kara <jack@suse.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16:
- file rename: fs/xfs/libxfs/xfs_da_format.h -> fs/xfs/xfs_da_format.h ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In the dir3 data block readahead function, use the regular read
verifier to check the block's CRC and spot-check the block contents
instead of directly calling only the spot-checking routine. This
prevents corrupted directory data blocks from being read into the
kernel, which can lead to garbage ls output and directory loops (if
say one of the entries contains slashes and other junk).
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[ luis: backported to 3.16:
- file rename: fs/xfs/libxfs/xfs_dir2_data.c -> fs/xfs/xfs_dir2_data.c
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Consider eCryptfs dcache entries to be stale when the corresponding
lower inode's i_nlink count is zero. This solves a problem caused by the
lower inode being directly modified, without going through the eCryptfs
mount, leaving stale eCryptfs dentries cached and the eCryptfs inode's
i_nlink count not being cleared.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Reported-by: Richard Weinberger <richard@nod.at>
[ luis: backported to 3.16:
- use dentry->d_inode instead of d_inode(dentry)
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
It was reported that after 10-20 reboots, a usb keyboard plugged
into a docking station would not work unless it was replugged in.
Using usbmon, it turns out the interrupt URBs were streaming with
callback errors of -71 for some reason. The hid-core.c::hid_io_error was
supposed to retry and then reset, but the reset wasn't really happening.
The check for HID_NO_BANDWIDTH was inverted. Fix was simple.
Tested by reporter and locally by me by unplugging a keyboard halfway until I
could recreate a stream of errors but no disconnect.
Signed-off-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When initializing igb driver (e.g. 82576, I350), IGB_FLAG_QUEUE_PAIRS is
set if adapter->rss_queues exceeds half of max_rss_queues in
igb_init_queue_configuration().
On the other hand, IGB_FLAG_QUEUE_PAIRS is not set even if the number of
queues exceeds half of max_combined in igb_set_channels() when changing
the number of queues by "ethtool -L".
In this case, if numvecs is larger than MAX_MSIX_ENTRIES (10), the size
of adapter->msix_entries[], an overflow can occur in
igb_set_interrupt_capability(), which in turn leads to an oops.
Fix this problem as follows:
- When changing the number of queues by "ethtool -L", set
IGB_FLAG_QUEUE_PAIRS in the same way as initializing igb driver.
- When increasing the size of q_vector, reallocate it appropriately.
(With IGB_FLAG_QUEUE_PAIRS set, the size of q_vector gets larger.)
Another possible way to fix this problem is to cap the queues at its
initial number, which is the number of the initial online cpus. But this
is not the optimal way because we cannot increase queues when another
cpu becomes online.
Note that before commit cd14ef54d25b ("igb: Change to use statically
allocated array for MSIx entries"), this problem did not cause oops
but just made the number of queues become 1 because of entering msi_only
mode in igb_set_interrupt_capability().
Fixes: 907b7835799f ("igb: Add ethtool support to configure number of channels") Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The driver used usb_get_serial_data(port->serial) which compiled but resulted
in a NULL pointer being returned (and subsequently used). I did not go deeper
into this but I guess this is a regression.
Signed-off-by: Philipp Hachtmann <hachti@hachti.de> Fixes: a85796ee5149 ("USB: symbolserial: move private-data allocation to
port_probe") Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We should ensure that we always set the pgio_header's error field
if a READ or WRITE RPC call returns an error. The current code depends
on 'hdr->good_bytes' always being initialised to a large value, which
is not always done correctly by callers.
When this happens, applications may end up missing important errors.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
call12 can't be safely used as the first call in the inline function,
because the compiler does not extend the stack frame of the bounding
function accordingly, which may result in corruption of local variables.
If a call needs to be done, do call8 first followed by call12.
For pure assembly code in _switch_to increase stack frame size of the
bounding function.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
There may be lots of pending requests so that the buffer of PAGE_SIZE
can't hold them at all.
One typical example is scsi-mq, the queue depth(.can_queue) of
scsi_host and blk-mq is quite big but scsi_device's queue_depth
is a bit small(.cmd_per_lun), then it is quite easy to have lots
of pending requests in hw queue.
This patch fixes the following warning and the related memory
destruction.
The "adl_pci7x3x" driver replaced the "adl_pci7230" and "adl_pci7432"
drivers in commits 8f567c373c4b ("staging: comedi: new adl_pci7x3x
driver") and 657f77d173d3 ("staging: comedi: remove adl_pci7230 and
adl_pci7432 drivers"). Although the new driver code agrees with the
user manuals for the respective boards, digital outputs stopped working
on the PCI-7230. This has 16 digital output channels and the previous
adl_pci7230 driver shifted the 16 bit output state left by 16 bits
before writing to the hardware register. The new adl_pci7x3x driver
doesn't do that. Fix it in `adl_pci7x3x_do_insn_bits()` by checking
for the special case of the subdevice having only 16 channels and
duplicating the 16 bit output state into both halves of the 32-bit
register. That should work both for what the board actually does and
for what the user manual says it should do.
Fixes: 8f567c373c4b ("staging: comedi: new adl_pci7x3x driver") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This way this device can be used with irtty-sir -
at least on Toshiba Satellite A20-S103 it is not configured by default
and needs PNP activation before it starts to respond on I/O ports.
This device has actually its own driver (ali-ircc),
but this driver seems to be non-functional for a very long time
(see http://permalink.gmane.org/gmane.linux.irda.general/484
http://permalink.gmane.org/gmane.network.protocols.obex.openobex.user/943
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=535070 ).
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
regulator_disable of pbias always writes '0' to the enable_reg.
However actual disable value of pbias regulator is not always '0'.
Fix it by populating the disable_val in pbias_reg_info for the
various platforms and assign it to the disable_val of
pbias regulator descriptor. This will be used by
regulator_disable_regmap while disabling pbias regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Don't set .read_flag_mask for adav803, it's for adav801 only.
Fixes: 0c2d69645628 ("ASoC: adav80x: Split SPI and I2C code into different modules") Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Before the make_empty_dir_inode calls were introduce into proc, sysfs,
and sysctl those directories when stated reported an i_size of 0.
make_empty_dir_inode started reporting an i_size of 2. At least one
userspace application depended on stat returning i_size of 0. So
modify make_empty_dir_inode to cause an i_size of 0 to be reported for
these directories.
Reported-by: Tejun Heo <tj@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In the logic in the initial commit of unshare made creating a new
thread group for a process, contingent upon creating a new memory
address space for that process. That is wrong. Two separate
processes in different thread groups can share a memory address space
and clone allows creation of such proceses.
This is significant because it was observed that mm_users > 1 does not
mean that a process is multi-threaded, as reading /proc/PID/maps
temporarily increments mm_users, which allows other processes to
(accidentally) interfere with unshare() calls.
Correct the check in check_unshare_flags() to test for
!thread_group_empty() for CLONE_THREAD, CLONE_SIGHAND, and CLONE_VM.
For sighand->count > 1 for CLONE_SIGHAND and CLONE_VM.
For !current_is_single_threaded instead of mm_users > 1 for CLONE_VM.
By using the correct checks in unshare this removes the possibility of
an accidental denial of service attack.
Additionally using the correct checks in unshare ensures that only an
explicit unshare(CLONE_VM) can possibly trigger the slow path of
current_is_single_threaded(). As an explict unshare(CLONE_VM) is
pointless it is not expected there are many applications that make
that call.
Fixes: b2e0d98705e60e45bbb3c0032c48824ad7ae0704 userns: Implement unshare of the user namespace Reported-by: Ricky Zhou <rickyz@chromium.org> Reported-by: Kees Cook <keescook@chromium.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
NFSv4 takes O_EXCL as a sign that a setattr command should be sent,
probably to reset the timestamps.
When it was an O_RDONLY open, the SETATTR command does not
identify any actual attributes to change.
If no delegation was provided to the open, the SETATTR uses the
all-zeros stateid and the request is accepted (at least by the
Linux NFS server - no harm, no foul).
If a read-delegation was provided, this is used in the SETATTR
request, and a Netapp filer will justifiably claim
NFS4ERR_BAD_STATEID, which the Linux client takes as a sign
to retry - indefinitely.
So only treat O_EXCL specially if O_CREAT was also given.
Negative return values are not supported by iio_event_poll since
its return type is unsigned int.
Fixes: f18e7a068a0a3 ("iio: Return -ENODEV for file operations if the device has been unregistered") Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The power for line out was not turned on when line out is enabled.
So we add "LOUT amp" widget to turn on the power for line out.
Signed-off-by: John Lin <john.lin@realtek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Like some of the other Yoga models the Lenovo Yoga 3 14 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 3 14 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1239050 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add inverse unit conversion macro to convert from standard IIO units to
units that might be used by some devices.
Those are useful in combination with scale factors that are specified as
IIO_VAL_FRACTIONAL. Typically the denominator for those specifications will
contain the maximum raw value the sensor will generate and the numerator
the value it maps to in a specific unit. Sometimes datasheets specify those
in different units than the standard IIO units (e.g. degree/s instead of
rad/s) and so we need to do a unit conversion.
From a mathematical point of view it does not make a difference whether we
apply the unit conversion to the numerator or the inverse unit conversion
to the denominator since (x / y) / z = x / (y * z). But as the denominator
is typically a larger value and we are rounding both the numerator and
denominator to integer values using the later method gives us a better
precision (E.g. the relative error is smaller if we round 8000.3 to 8000
rather than rounding 8.3 to 8).
This is where in inverse unit conversion macros will be used.
Marked for stable as used by some upcoming fixes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
parport_find_base() will implicitly do parport_get_port() which
increases the refcount. Then parport_register_device() will again
increment the refcount. But while unloading the module we are only
doing parport_unregister_device() decrementing the refcount only once.
We add an parport_put_port() to neutralize the effect of
parport_get_port().
We got the bug that qemu complained with "KVM: unknown exit, hardware
reason 31" and KVM shown these info:
[84245.284948] EPT: Misconfiguration.
[84245.285056] EPT: GPA: 0xfeda848
[84245.285154] ept_misconfig_inspect_spte: spte 0x5eaef50107 level 4
[84245.285344] ept_misconfig_inspect_spte: spte 0x5f5fadc107 level 3
[84245.285532] ept_misconfig_inspect_spte: spte 0x5141d18107 level 2
[84245.285723] ept_misconfig_inspect_spte: spte 0x52e40dad77 level 1
This is because we got a mmio #PF and the handler see the mmio spte becomes
normal (points to the ram page)
However, this is valid after introducing fast mmio spte invalidation which
increases the generation-number instead of zapping mmio sptes, a example
is as follows:
1. QEMU drops mmio region by adding a new memslot
2. invalidate all mmio sptes
3.
VCPU 0 VCPU 1
access the invalid mmio spte
access the region originally was MMIO before
set the spte to the normal ram map
mmio #PF
check the spte and see it becomes normal ram mapping !!!
This patch fixes the bug just by dropping the check in mmio handler, it's
good for backport. Full check will be introduced in later patches
Reported-by: Pavel Shirshov <ru.pchel@gmail.com> Tested-by: Pavel Shirshov <ru.pchel@gmail.com> Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: Adam Lee <adam.lee@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.
Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The TSADC gate clock was used in Exynos4x12 DTSI for exynos-adc driver.
However TSADC is present only on Exynos4210 so on Trats2 board (with
Exynos4412 SoC) the exynos-adc driver could not be probed:
ERROR: could not get clock /adc@126C0000:adc(0)
exynos-adc 126c0000.adc: failed getting clock, err = -2
exynos-adc: probe of 126c0000.adc failed with error -2
Instead on Exynos4x12 SoCs the main clock used by Analog to Digital
Converter is located in different register and it is named in datasheet
as PCLK_ADC. Regardless of the name the purpose of this PCLK_ADC clock
is the same as purpose of TSADC from Exynos4210.
The patch adds gate clock for Exynos4x12 using the proper register so
backward compatibility is preserved. This fixes the probe of exynos-adc
driver on Exynos4x12 boards and allows accessing sensors connected to it
on Trats2 board (ntc,ncp15wb473 AP and battery thermistors).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: c63c57433003 ("ARM: dts: Add ADC's dt data to read raw data for exynos4x12") Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
`devpriv->ao_timer` is used while an asynchronous command is running on
the AO subdevice. It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands,
`usbduxsigma_ao_cmdtest()`, which is not correct as it's allowed to
check new commands while an old command is still running. Fix it by
moving the code which sets up `devpriv->ao_timer` into the subdevice's
`cmd` handler, `usbduxsigma_ao_cmd()`.
** This backported patch also moves the code that sets up
`devpriv->ao_sample_count` from `usbduxsigma_ao_cmdtest()` to
`usbduxsigma_ao_cmd()` for the same reason as above. (This was not
needed in the upstream commit.) **
Note that the removed code in `usbduxsigma_ao_cmdtest()` checked that
`devpriv->ao_timer` did not end up less that 1, but that could not
happen due because `cmd->scan_begin_arg` or `cmd->convert_arg` had
already been range-checked.
Also note that we tested the `high_speed` variable in the old code, but
that is currently always 0 and means that we always use "scan" timing
(`cmd->scan_begin_src == TRIG_TIMER` and `cmd->convert_src == TRIG_NOW`)
and never "convert" (individual sample) timing (`cmd->scan_begin_src ==
TRIG_FOLLOW` and `cmd->convert_src == TRIG_TIMER`). The moved code
tests `cmd->convert_src` instead to decide whether "scan" or "convert"
timing is being used, although currently only "scan" timing is
supported.
Fixes: fb1ef622e7a3 ("staging: comedi: usbduxsigma: tidy up analog output command support") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
`devpriv->ai_timer` is used while an asynchronous command is running on
the AI subdevice. It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands
(`usbduxsigma_ai_cmdtest()`), which is not correct as it's allowed to
check new commands while an old command is still running. Fix it by
moving the code which sets up `devpriv->ai_timer` and
`devpriv->ai_interval` into the subdevice's `cmd` handler,
`usbduxsigma_ai_cmd()`.
** This backported patch also moves the code that sets up
`devpriv->ai_sample_count` from `usbduxsigma_ai_cmdtest()` to
`usbduxsigma_ai_cmd()` for the same reason as above. (This was not
needed in the upstream commit.) **
Note that the removed code in `usbduxsigma_ai_cmdtest()` checked that
`devpriv->ai_timer` did not end up less than than 1, but that could not
happen because `cmd->scan_begin_arg` had already been checked to be at
least the minimum required value (at least when `cmd->scan_begin_src ==
TRIG_TIMER`, which had also been checked to be the case).
Fixes: b986be8527c7 ("staging: comedi: usbduxsigma: tidy up analog input command support) Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog] Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions. This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions. Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.
On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang. This has to do with how the kernel tracks the expected value of the
F bit per function.
Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.
When hangs occur, typically the error message:
vpd r/w failed. This is likely a firmware bug on this device.
will be seen.
Never set this bit on function 0 or there will be an infinite recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
We already set a station to be associated when peering completes, both
in user space and in the kernel. Thus we should always have an
associated sta before sending data frames to that station.
Failure to check assoc state can cause crashes in the lower-level driver
due to transmitting unicast data frames before driver sta structures
(e.g. ampdu state in ath9k) are initialized. This occurred when
forwarding in the presence of fixed mesh paths: frames were transmitted
to stations with whom we hadn't yet completed peering.
Reported-by: Alexis Green <agreen@cococorp.com> Tested-by: Jesse Jones <jjones@cococorp.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Legacy IPs like PWMSS, present under l4per2_7xx_clkdm, cannot support
smart-idle when its clock domain is in HW_AUTO on DRA7 SoCs. Hence,
program clock domain to SW_WKUP.
Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Reviewed-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Userspace return code may skip restoring THREADPTR register if there are
no registers that need to be zeroed. This leads to spurious failures in
libc NPTL tests.
Always restore THREADPTR on return to userspace.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Change all occurrences of be16 to le16 in cp2112_xfer(),
because SMBUS words are little endian, not big endian.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When doing an I2C_SMBUS_BYTE write (one byte write, no address),
the data to be written is in "command" not "data->byte".
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com> Acked-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The input_dev is already gone when the rc device is being unregistered
so checking for its presence only means that no remove uevent will be
generated.
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 813f5c0ac5cc ("media: Change media device link_notify behaviour")
modified the media controller link setup notification API and updated the
OMAP3 ISP driver accordingly. As a side effect it introduced a bug by
turning power on after setting the link instead of before. This results in
sub-devices not being powered down in some cases when they should be. Fix
it.
Fixes: 813f5c0ac5cc [media] media: Change media device link_notify behaviour Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
virtio declares support for NETIF_F_FRAGLIST, but assumes
that there are at most MAX_SKB_FRAGS + 2 fragments which isn't
always true with a fraglist.
A longer fraglist in the skb will make the call to skb_to_sgvec overflow
the sg array, leading to memory corruption.
Drop NETIF_F_FRAGLIST so we only get what we can handle.
Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Moritz Muehlenhoff <jmm@debian.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Currently we don't check if the new MTU is valid or not and this allows
one to configure a smaller than minimum allowed by RFCs or even bigger
than interface own MTU, which is a problem as it may lead to packet
drops.
If you have a daemon like NetworkManager running, this may be exploited
by remote attackers by forging RA packets with an invalid MTU, possibly
leading to a DoS. (NetworkManager currently only validates for values
too small, but not for too big ones.)
The fix is just to make sure the new value is valid. That is, between
IPV6_MIN_MTU and interface's MTU.
Note that similar check is already performed at
ndisc_router_discovery(), for when kernel itself parses the RA.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Moritz Muehlenhoff <jmm@debian.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This function can leak kernel stack data when the user siginfo_t has a
positive si_code value. The top 16 bits of si_code descibe which fields
in the siginfo_t union are active, but they are treated inconsistently
between copy_siginfo_from_user32, copy_siginfo_to_user32 and
copy_siginfo_to_user.
copy_siginfo_from_user32 is called from rt_sigqueueinfo and
rt_tgsigqueueinfo in which the user has full control overthe top 16 bits
of si_code.
This fixes the following information leaks:
x86: 8 bytes leaked when sending a signal from a 32-bit process to
itself. This leak grows to 16 bytes if the process uses x32.
(si_code = __SI_CHLD)
x86: 100 bytes leaked when sending a signal from a 32-bit process to
a 64-bit process. (si_code = -1)
sparc: 4 bytes leaked when sending a signal from a 32-bit process to a
64-bit process. (si_code = any)
parsic and s390 have similar bugs, but they are not vulnerable because
rt_[tg]sigqueueinfo have checks that prevent sending a positive si_code
to a different process. These bugs are also fixed for consistency.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This function may copy the si_addr_lsb, si_lower and si_upper fields to
user mode when they haven't been initialized, which can leak kernel
stack data to user mode.
Just checking the value of si_code is insufficient because the same
si_code value is shared between multiple signals. This is solved by
checking the value of si_signo in addition to si_code.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ luis: backported to 3.16:
- dropped 2nd hunk in kernel/signal.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This function may copy the si_addr_lsb field to user mode when it hasn't
been initialized, which can leak kernel stack data to user mode.
Just checking the value of si_code is insufficient because the same
si_code value is shared between multiple signals. This is solved by
checking the value of si_signo in addition to si_code.
While gntdev_release() is called the MMU notifier is still registered
and can traverse priv->maps list even if no pages are mapped (which is
the case -- gntdev_release() is called after all). But
gntdev_release() will clear that list, so make sure that only one of
those things happens at the same time.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Fix this error when compiling with CONFIG_SMP=n and
CONFIG_DYNAMIC_DEBUG=y:
drivers/s390/char/sclp_early.c: In function 'sclp_read_info_early':
drivers/s390/char/sclp_early.c:87:19: error: 'EBUSY' undeclared (first use in this function)
} while (rc == -EBUSY);
^
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Stephen Powell <zlinuxman@wowway.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When a tunnel is deleted, the cached dst entry should be released.
This problem may prevent the removal of a netns (seen with a x-netns IPv6
gre tunnel):
unregister_netdevice: waiting for lo to become free. Usage count = 3
CC: Dmitry Kozlov <xeb@mail.ru> Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: huaibin Wang <huaibin.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In pfkey_sendmsg the net mutex is taken and then pfkey_broadcast takes
the RCU lock.
Since pfkey_broadcast takes the RCU lock the allocation argument is
pointless since GFP_ATOMIC must be used between the rcu_read_{,un}lock.
The one call outside of rcu can be done with GFP_KERNEL.
Fixes: 7f6b9dbd5afbd ("af_key: locking change") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The tt_local_entry deletion performed in batadv_tt_local_remove() was neither
protecting against simultaneous deletes nor checking whether the element was
still part of the list before calling hlist_del_rcu().
Replacing the hlist_del_rcu() call with batadv_hash_remove() provides adequate
protection via hash spinlocks as well as an is-element-still-in-hash check to
avoid 'blind' hash removal.
Fixes: 068ee6e204e1 ("batman-adv: roaming handling mechanism redesign") Reported-by: alfonsname@web.de Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When injecting a fault into a misbehaving 32bit guest, it seems
rather idiotic to also inject a 64bit fault that is only going
to corrupt the guest state. This leads to a situation where we
perform an illegal exception return at EL2 causing the host
to crash instead of killing the guest.
Just fix the stupid bug that has been there from day 1.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.
The new naming convention boils down to: s/Crucial_/FC/
Signed-off-by: Guillermo A. Amaral <g@maral.me> Signed-off-by: Tejun Heo <tj@kernel.org>
[ luis: backported to 3.16:
- dropped ATA_HORKAGE_ZERO_AFTER_TRIM flag
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The fix for deadlock in PM in commit [1ee23fe07ee8: ALSA: usb-audio:
Fix deadlocks at resuming] introduced a new check of in_pm flag.
However, the brainless patch author evaluated it in a wrong way
(logical AND instead of logical OR), thus usb_autopm_get_interface()
is wrongly called at probing, leading to unbalance of runtime PM
refcount.
This patch fixes it by correcting the logic.
Reported-by: Hans Yang <hansy@nvidia.com> Fixes: 1ee23fe07ee8 ('ALSA: usb-audio: Fix deadlocks at resuming') Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The routines in scsi_rpm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by calling the block layer's runtime-PM
routines only if the device's driver really does have a runtime-PM
callback routine. Since ses doesn't define any such callbacks, the
crash won't occur.
This fixes Bugzilla #101371.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Stanisław Pitucha <viraptor@gmail.com> Reported-by: Ilan Cohen <ilanco@gmail.com> Tested-by: Ilan Cohen <ilanco@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Commit 4c21b8fd8f14 ("MIPS: seccomp: Handle indirect system calls (o32)")
fixed indirect system calls on O32 but it also introduced a bug for MIPS64
where it erroneously modified the v0 (syscall) register with the assumption
that the sycall offset hasn't been taken into consideration. This breaks
seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition
with a move instruction.
Fixes: 4c21b8fd8f14 ("MIPS: seccomp: Handle indirect system calls (o32)") Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10951/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
!spin_is_locked() and spin_unlock_wait() are both only control barriers.
The code needs an acquire barrier, otherwise the cpu might perform read
operations before the lock test.
As no primitive exists inside <include/spinlock.h> and since it seems
noone wants another primitive, the code creates a local primitive within
ipc/sem.c.
With regards to -stable:
The change of sem_wait_array() is a bugfix, the change to sem_lock() is a
nop (just a preprocessor redefinition to improve the readability). The
bugfix is necessary for all kernels that use sem_wait_array() (i.e.:
starting from 3.10).
When I fixed bugs in the sem_lock() logic, I was more conservative than
necessary. Therefore it is safe to replace the smp_mb() with smp_rmb().
And: With smp_rmb(), semop() syscalls are up to 10% faster.
The race we must protect against is:
sem->lock is free
sma->complex_count = 0
sma->sem_perm.lock held by thread B
The current semaphore code allows a potential use after free: in
exit_sem we may free the task's sem_undo_list while there is still
another task looping through the same semaphore set and cleaning the
sem_undo list at freeary function (the task called IPC_RMID for the same
semaphore set).
For example, with a test program [1] running which keeps forking a lot
of processes (which then do a semop call with SEM_UNDO flag), and with
the parent right after removing the semaphore set with IPC_RMID, and a
kernel built with CONFIG_SLAB, CONFIG_SLAB_DEBUG and
CONFIG_DEBUG_SPINLOCK, you can easily see something like the following
in the kernel log:
I wasn't able to trigger any badness on a recent kernel without the
proper config debugs enabled, however I have softlockup reports on some
kernel versions, in the semaphore code, which are similar as above (the
scenario is seen on some servers running IBM DB2 which uses semaphore
syscalls).
The patch here fixes the race against freeary, by acquiring or waiting
on the sem_undo_list lock as necessary (exit_sem can race with freeary,
while freeary sets un->semid to -1 and removes the same sem_undo from
list_proc or when it removes the last sem_undo).
After the patch I'm unable to reproduce the problem using the test case
[1].
void create_set()
{
int i, j;
pid_t p;
union {
int val;
struct semid_ds *buf;
unsigned short int *array;
struct seminfo *__buf;
} un;
/* Create and initialize semaphore set */
for (i = 0; i < NSET; i++) {
sid[i] = semget(IPC_PRIVATE , NSEM, 0644 | IPC_CREAT);
if (sid[i] < 0) {
perror("semget");
exit(EXIT_FAILURE);
}
}
un.val = 0;
for (i = 0; i < NSET; i++) {
for (j = 0; j < NSEM; j++) {
if (semctl(sid[i], j, SETVAL, un) < 0)
perror("semctl");
}
}
/* Launch threads that operate on semaphore set */
for (i = 0; i < NSEM * NSET * NSET; i++) {
p = fork();
if (p < 0)
perror("fork");
if (p == 0)
thread();
}
/* Free semaphore set */
for (i = 0; i < NSET; i++) {
if (semctl(sid[i], NSEM, IPC_RMID))
perror("IPC_RMID");
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
int main(int argc, char **argv)
{
pid_t p;
srand(time(NULL));
while (1) {
p = fork();
if (p < 0) {
perror("fork");
exit(EXIT_FAILURE);
}
if (p == 0) {
create_set();
goto end;
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
end:
return 0;
}
[akpm@linux-foundation.org: use normal comment layout] Signed-off-by: Herton R. Krzesinski <herton@redhat.com> Acked-by: Manfred Spraul <manfred@colorfullife.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Rafael Aquini <aquini@redhat.com> CC: Aristeu Rozanski <aris@redhat.com> Cc: David Jeffery <djeffery@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
After trying to drain pages from pagevec/pageset, we try to get reference
count of the page again, however, the reference count of the page is not
reduced if the page is still not on LRU list.
Fix it by adding the put_page() to drop the page reference which is from
__get_any_page().
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This addresses two issues that cause problems with viewperf maya-03 in
situation with memory pressure.
The first issue causes attempts to unreserve buffers if batched
reservation fails due to, for example, a signal pending. While previously
the ttm_eu api was resistant against this type of error, it is no longer
and the lockdep code will complain about attempting to unreserve buffers
that are not reserved. The issue is resolved by avoid calling
ttm_eu_backoff_reservation in the buffer reserve error path.
The second issue is that the binding_mutex may be held when user-space
fence objects are created and hence during memory reclaims. This may cause
recursive attempts to grab the binding mutex. The issue is resolved by not
holding the binding mutex across fence creation and submission.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Since fc_fcp_cleanup_cmd() can sleep this function must not
be called while holding a spinlock. This patch avoids that
fc_fcp_cleanup_each_cmd() triggers the following bug:
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Due to patch "libfc: Do not invoke the response handler after
fc_exch_done()" (commit ID 7030fd62) the lport_recv() call
in fc_exch_recv_req() is passed a dangling pointer. Avoid this
by moving the fc_frame_free() call from fc_invoke_resp() to its
callers. This patch fixes the following crash:
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In case of hw iscsi offload, an host can have N-number of active
connections. There can be IO's running on some connections which
make host->host_busy always TRUE. Now if logout from a connection
is tried then the code gets into an infinite loop as host->host_busy
is always TRUE.
iscsi_conn_teardown(....)
{
.........
/*
* Block until all in-progress commands for this connection
* time out or fail.
*/
for (;;) {
spin_lock_irqsave(session->host->host_lock, flags);
if (!atomic_read(&session->host->host_busy)) { /* OK for ERL == 0 */
spin_unlock_irqrestore(session->host->host_lock, flags);
break;
}
spin_unlock_irqrestore(session->host->host_lock, flags);
msleep_interruptible(500);
iscsi_conn_printk(KERN_INFO, conn, "iscsi conn_destroy(): "
"host_busy %d host_failed %d\n",
atomic_read(&session->host->host_busy),
session->host->host_failed);
................
...............
}
}
This is not an issue with software-iscsi/iser as each cxn is a separate
host.
Fix:
Acquiring eh_mutex in iscsi_conn_teardown() before setting
session->state = ISCSI_STATE_TERMINATE.
Signed-off-by: John Soni Jose <sony.john@avagotech.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
[ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When using nested btrees, the top leaves of the top levels contain
block addresses for the root of the next tree down. If we shadow a
shared leaf node the leaf values (sub tree roots) should be incremented
accordingly.
This is only an issue if there is metadata sharing in the top levels.
Which only occurs if metadata snapshots are being used (as is possible
with dm-thinp). And could result in a block from the thinp metadata
snap being reused early, thus corrupting the thinp metadata snap.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[ luis: backported to 3.16:
- dropped changes to remove_one() as suggested by Mike Snitzer ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
The device details and mapping trees were just being decremented
before. Now btree_del() is called to do a deep delete.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
In kbuild it is allowed to define objects in files named "Makefile"
and "Kbuild".
Currently localmodconfig reads objects only from "Makefile"s and misses
modules like nouveau.
Link: http://lkml.kernel.org/r/1437948415-16290-1-git-send-email-richard@nod.at Reported-and-tested-by: Leonidas Spyropoulos <artafinde@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
I want to use lockless_dereference() from seqlock.h, which would mean
including rcupdate.h from it, however rcupdate.h already includes
seqlock.h.
Avoid this by moving lockless_dereference() into compiler.h. This is
somewhat tricky since it uses smp_read_barrier_depends() which isn't
available there, but its a CPP macro so we can get away with it.
The alternative would be moving it into asm/barrier.h, but that would
be updating each arch (I can do if people feel that is more
appropriate).
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
[ luis: 3.16 prereq for: 37868fe113ff "x86/ldt: Make modify_ldt synchronous" ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Although rcu_dereference() and friends can be used in situations where
object lifetimes are being managed by something other than RCU, the
resulting sparse and lockdep-RCU noise can be annoying. This commit
therefore supplies a lockless_dereference(), which provides the
protection for dereferences without the RCU-related debugging noise.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ luis: 3.16 prereq for: 37868fe113ff "x86/ldt: Make modify_ldt synchronous" ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
modify_ldt() has questionable locking and does not synchronize
threads. Improve it: redesign the locking and synchronize all
threads' LDTs using an IPI on all modifications.
This will dramatically slow down modify_ldt in multithreaded
programs, but there shouldn't be any multithreaded programs that
care about modify_ldt's performance in the first place.
This fixes some fallout from the CVE-2015-5157 fixes.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: security@kernel.org <security@kernel.org> Cc: xen-devel <xen-devel@lists.xen.org> Link: http://lkml.kernel.org/r/4c6978476782160600471bd865b318db34c7b628.1438291540.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ luis: backported to 3.16:
- dropped changes to comments in switch_mm()
- included asm/mmu_context.h in perf_event.c
- adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
When kvm_set_msr_common() handles a guest's write to
MSR_IA32_TSC_ADJUST, it will calcuate an adjustment based on the data
written by guest and then use it to adjust TSC offset by calling a
call-back adjust_tsc_offset(). The 3rd parameter of adjust_tsc_offset()
indicates whether the adjustment is in host TSC cycles or in guest TSC
cycles. If SVM TSC scaling is enabled, adjust_tsc_offset()
[i.e. svm_adjust_tsc_offset()] will first scale the adjustment;
otherwise, it will just use the unscaled one. As the MSR write here
comes from the guest, the adjustment is in guest TSC cycles. However,
the current kvm_set_msr_common() uses it as a value in host TSC
cycles (by using true as the 3rd parameter of adjust_tsc_offset()),
which can result in an incorrect adjustment of TSC offset if SVM TSC
scaling is enabled. This patch fixes this problem.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Vince reported that the fasync signal stuff doesn't work proper for
inherited events. So fix that.
Installing fasync allocates memory and sets filp->f_flags |= FASYNC,
which upon the demise of the file descriptor ensures the allocation is
freed and state is updated.
Now for perf, we can have the events stick around for a while after the
original FD is dead because of references from child events. So we
cannot copy the fasync pointer around. We can however consistently use
the parent's fasync, as that will be updated.
Reported-and-Tested-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho deMelo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: eranian@google.com Link: http://lkml.kernel.org/r/1434011521.1495.71.camel@twins Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
projects / thirdparty / kernel / stable.git / log
