Reservations in gfs can span multiple gfs2_bitmaps (but they won't span
multiple resource groups). When removing a reservation, we want to
clear the GBF_FULL flags of all involved gfs2_bitmaps, not just that of
the first bitmap.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the PCIe specification, although the MSI data is only
16bits, the upper 16bits should be written as 0. Use writel
instead of writew when writing the MSI data to the host.
Fixes: 37dddf14f1ae ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller") Signed-off-by: Alan Douglas <adouglas@cadence.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a potential execution path in which variable *ret* is checked
in an IF statement, and then its value is used to report an error at
line 659 without being properly initialized previously:
659 if (ret)
660 dev_err(priv->dev, "Failed to write to 0x%x (%d)\n", reg, ret);
Fix this by initializing variable *ret* to 0 in order to
avoid unpredictable or unintended results.
Addresses-Coverity-ID: 1471969 ("Uninitialized scalar variable") Fixes: 218d72a77b0b ("pinctrl: madera: Add driver for Cirrus Logic Madera codecs") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Prior to commit 5c2992ee7fd8a29 ("printk: remove console flushing special
cases for partial buffered lines") we would do console_cont_flush()
for each pr_cont() to print cont fragments, so console_unlock() would
actually print data:
pr_cont();
console_lock();
console_unlock()
console_cont_flush(); // print cont fragment
...
pr_cont();
console_lock();
console_unlock()
console_cont_flush(); // print cont fragment
We don't do console_cont_flush() anymore, so when we do pr_cont()
console_unlock() does nothing (unless we flushed the cont buffer):
We also wakeup klogd purposelessly for pr_cont() output - un-flushed
cont buffer is not stored in log_buf; there is nothing to pull.
Thus we can console_lock()/console_unlock()/wake_up_klogd() only when
we know that we log_store()-ed a message and there is something to
print to the consoles/syslog.
Link: http://lkml.kernel.org/r/20181002023836.4487-3-sergey.senozhatsky@gmail.com
To: Steven Rostedt <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Tejun Heo <tj@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: LKML <linux-kernel@vger.kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After allocation, output and decomp_output both point to memory chunks of
size COMP_BUF_SIZE. Then, only the first bytes are zeroed out using
sizeof(COMP_BUF_SIZE) as parameter to memset(), because
sizeof(COMP_BUF_SIZE) provides the size of the constant and not the size of
allocated memory.
Instead, the whole allocated memory is meant to be zeroed out. Use
COMP_BUF_SIZE as parameter to memset() directly in order to accomplish
this.
Fixes: 336073840a872 ("crypto: testmgr - Allow different compression results") Signed-off-by: Michael Schupikov <michael@schupikov.de> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
NL80211_TX_POWER_LIMITED was treated as NL80211_TX_POWER_AUTOMATIC,
which is the opposite of what should happen and can cause nasty
regulatory problems.
if/else converted to a switch without default to make gcc warn
on unhandled enum values.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For pages with a mapping this should be done under the page lock
for the benefit of asynchronous memory errors who prefer a
consistent dirty state. This rule can be broken in some special
cases, but should be better not to.
Under those rules, it is only safe for us to use the plain set_page_dirty
calls for shmemfs/anonymous memory. Userptr may be used with real
mappings and so needs to use the locked version (set_page_dirty_lock).
However, following a try_to_unmap() we may want to remove the userptr and
so call put_pages(). However, try_to_unmap() acquires the page lock and
so we must avoid recursively locking the pages ourselves -- which means
that we cannot safely acquire the lock around set_page_dirty(). Since we
can't be sure of the lock, we have to risk skip dirtying the page, or
else risk calling set_page_dirty() without a lock and so risk fs
corruption.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203317
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112012 Fixes: 5cc9ed4b9a7a ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl")
References: cb6d7c7dc7ff ("drm/i915/userptr: Acquire the page lock around set_page_dirty()")
References: 505a8ec7e11a ("Revert "drm/i915/userptr: Acquire the page lock around set_page_dirty()"")
References: 6dcc693bc57f ("ext4: warn when page is dirtied without buffers") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: stable@vger.kernel.org Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191111133205.11590-1-chris@chris-wilson.co.uk
(cherry picked from commit 0d4bbe3d407f79438dc4f87943db21f7134cfc65) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit cee7fb437edcdb2f9f8affa959e274997f5dca4d) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We report "frequencies" (actual-frequency, requested-frequency) as the
number of accumulated cycles so that the average frequency over that
period may be determined by the user. This means the units we report to
the user are Mcycles (or just M), not MHz.
It's possible to hit the WARN_ON_ONCE(page_mapped(page)) in
remove_stable_node() when it races with __mmput() and squeezes in
between ksm_exit() and exit_mmap().
WARNING: CPU: 0 PID: 3295 at mm/ksm.c:888 remove_stable_node+0x10c/0x150
Commit 56e94ea132bb ("fs: ocfs2: fix possible null-pointer dereferences
in ocfs2_xa_prepare_entry()") introduces a regression that fail to
create directory with mount option user_xattr and acl. Actually the
reported NULL pointer dereference case can be correctly handled by
loc->xl_ops->xlo_add_entry(), so revert it.
Link: http://lkml.kernel.org/r/1573624916-83825-1-git-send-email-joseph.qi@linux.alibaba.com Fixes: 56e94ea132bb ("fs: ocfs2: fix possible null-pointer dereferences in ocfs2_xa_prepare_entry()") Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reported-by: Thomas Voegtle <tv@lio96.de> Acked-by: Changwei Ge <gechangwei@live.cn> Cc: Jia-Ju Bai <baijiaju1990@gmail.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because buffers for the in_vq are allocated when the port is
added but are not released when the port is unplugged.
They are only released when virtconsole is removed (see a7a69ec0d8e4)
To avoid the problem and to be symmetric, we could allocate all the buffers
in init_vqs() as they are released in remove_vqs(), but it sounds like
a waste of memory.
Rather than that, this patch changes add_port() logic to ignore ENOSPC
error in fill_queue(), which means queue has already been filled.
Fixes: a7a69ec0d8e4 ("virtio_console: free buffers after reset") Cc: mst@redhat.com Cc: stable@vger.kernel.org Signed-off-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When converting milliseconds to microseconds in commit fffa6af94894
("gpio: max77620: Use correct unit for debounce times") some ~1 ms gaps
were introduced between the various ranges supported by the controller.
Fix this by changing the start of each range to the value immediately
following the end of the previous range. This way a debounce time of,
say 8250 us will translate into 16 ms instead of returning an -EINVAL
error.
Typically the debounce delay is only ever set through device tree and
specified in milliseconds, so we can never really hit this issue because
debounce times are always a multiple of 1000 us.
The only notable exception for this is drivers/mmc/host/mmc-spi.c where
the CD GPIO is requested, which passes a 1 us debounce time. According
to a comment preceeding that code this should actually be 1 ms (i.e.
1000 us).
If the packets to sent to the guest are bigger than the buffer
available, we can split them, using multiple buffers and fixing
the length in the packet header.
This is safe since virtio-vsock supports only stream sockets.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once all the large flow groups (defined by the user when the flow table
is created - max_num_groups) were created, then all the following new
flow groups will have only one flow table entry, even though the flow table
has place to larger groups.
Fix the condition to prefer large flow group.
Array mlxfw_fsm_state_err_str contains value to string translation, when
values are provided by mlxfw_dev. If value is larger than
MLXFW_FSM_STATE_ERR_MAX, return "unknown error" as expected instead of
reading an address than exceed array size.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workqueue only exists for the primary PF. For other functions
we hit a WARN_ON in kernel/workqueue.c.
Fixes: 7c236c43b838 ("sfc: Add support for IEEE-1588 PTP") Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
info->options_len is 'u8' type, and when opts_len with a value >
IP_TUNNEL_OPTS_MAX, 'info->options_len = opts_len' will cast int
to u8 and set a wrong value to info->options_len.
Kernel crashed in my test when doing:
# opts="0102:80:00800022"
# for i in {1..99}; do opts="$opts,0102:80:00800022"; done
# ip link add name geneve0 type geneve dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 ip_proto udp action tunnel_key \
set src_ip 10.0.99.192 dst_ip 10.0.99.193 \
dst_port 6081 id 11 geneve_opts $opts \
action mirred egress redirect dev geneve0
So we should do the similar check as cls_flower does, return error
when opts_len > IP_TUNNEL_OPTS_MAX in tunnel_key_copy_opts().
Fixes: 0ed5269f9e41 ("net/sched: add tunnel option support to act_tunnel_key") Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when configuring act_pedit rules, the number of keys is validated only on
addition of a new entry. This is not sufficient to avoid hitting a WARN()
in the traffic path: for example, it is possible to replace a valid entry
with a new one having 0 extended keys, thus causing splats in dmesg like:
The "ivm->vf" variable is a u32, but the problem is that a number of
drivers cast it to an int and then forget to check for negatives. An
example of this is in the cxgb4 driver.
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8435 hclge_set_vf_vlan_filter() warn: can 'vfid' underflow 's32min-2147483646'
drivers/net/ethernet/freescale/enetc/enetc_pf.c:377 enetc_pf_set_vf_mac() warn: can 'vf' underflow 's32min-2147483646'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2899 cxgb4_mgmt_get_vf_config() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2960 cxgb4_mgmt_set_vf_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3019 cxgb4_mgmt_set_vf_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3038 cxgb4_mgmt_set_vf_vlan() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3086 cxgb4_mgmt_set_vf_link_state() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:791 get_eeprom() warn: can 'i' underflow 's32min-(-4),0,4-s32max'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:82 bnxt_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:164 bnxt_set_vf_trust() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:186 bnxt_get_vf_config() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:228 bnxt_set_vf_mac() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:264 bnxt_set_vf_vlan() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:293 bnxt_set_vf_bw() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:333 bnxt_set_vf_link_state() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:2595 bnx2x_vf_op_prep() warn: can 'vfidx' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:2595 bnx2x_vf_op_prep() warn: can 'vfidx' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2281 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2285 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2286 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2292 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2297 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1832 qlcnic_sriov_set_vf_mac() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1864 qlcnic_sriov_set_vf_tx_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1937 qlcnic_sriov_set_vf_vlan() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:2005 qlcnic_sriov_get_vf_config() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:2036 qlcnic_sriov_set_vf_spoofchk() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/emulex/benet/be_main.c:1914 be_get_vf_config() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1915 be_get_vf_config() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1922 be_set_vf_tvt() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1951 be_clear_vf_tvt() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:2063 be_set_vf_tx_rate() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:2091 be_set_vf_link_state() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:2609 ice_set_vf_port_vlan() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3050 ice_get_vf_cfg() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3103 ice_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3181 ice_set_vf_mac() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3237 ice_set_vf_trust() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3286 ice_set_vf_link_state() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:3919 i40e_validate_vf() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:3957 i40e_ndo_set_vf_mac() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4104 i40e_ndo_set_vf_port_vlan() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4263 i40e_ndo_set_vf_bw() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4309 i40e_ndo_get_vf_config() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4371 i40e_ndo_set_vf_link_state() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4441 i40e_ndo_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4441 i40e_ndo_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4504 i40e_ndo_set_vf_trust() warn: can 'vf_id' underflow 's32min-2147483646'
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XDP_TX rings should not be limited by max_num_tx_rings_p_up.
To make sure total number of TX rings never exceed MAX_TX_RINGS,
add similar check in mlx4_en_alloc_tx_queue_per_tc(), where
a new value is assigned for num_up.
Fixes: 7e1dc5e926d5 ("net/mlx4_en: Limit the number of TX rings") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ethtool expects ETHTOOL_GRXCLSRLALL to set ethtool_rxnfc->data with the
total number of entries in the rx classifier table. Surprisingly, mlx4
is missing this part (in principle ethtool could still move forward and
try the insert).
Tested: compiled and run command:
phh13:~# ethtool -N eth1 flow-type udp4 queue 4
Added rule with ID 255
The helper mlxsw_sp_ipip_dev_ul_tb_id() determines the underlay VRF of a
GRE tunnel. For a tunnel without a bound device, it uses the same VRF that
the tunnel is in. However in Linux, a GRE tunnel without a bound device
uses the main VRF as the underlay. Fix the function accordingly.
mlxsw further assumed that moving a tunnel to a different VRF could cause
conflict in local tunnel endpoint address, which cannot be offloaded.
However, the only way that an underlay could be changed by moving the
tunnel device itself is if the tunnel device does not have a bound device.
But in that case the underlay is always the main VRF, so there is no
opportunity to introduce a conflict by moving such device. Thus this check
constitutes a dead code, and can be removed, which do.
Fixes: 6ddb7426a7d4 ("mlxsw: spectrum_router: Introduce loopback RIFs") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rdt_find_domain() returns an ERR_PTR() that is generated from a provided
domain id when the value is negative.
Care needs to be taken when creating an ERR_PTR() from this value
because a subsequent check using IS_ERR() expects the error to
be within the MAX_ERRNO range. Using an invalid domain id as an
ERR_PTR() does work at this time since this is currently always -1.
Using this undocumented assumption is fragile since future users of
rdt_find_domain() may not be aware of thus assumption.
Two related issues are addressed:
- Ensure that rdt_find_domain() always returns a valid error value by
forcing the error to be -ENODEV when a negative domain id is provided.
- In a few instances the return value of rdt_find_domain() is just
checked for NULL - fix these to include a check of ERR_PTR.
check_scc_error() checks SCC_RVSREQ.RVSERR bit. RVSERR detects a
correction error in the next (up or down) delay tap position. However,
since the command is successful, only retuning needs to be executed.
This has been confirmed by HW engineers.
Thus, on SCC error, set retuning flag instead of setting an error code.
In the recent commit 8b78fdb045de ("powerpc/time: Use
clockevents_register_device(), fixing an issue with large
decrementer") we changed the way we initialise the decrementer
clockevent(s).
We no longer initialise the mult & shift values of
decrementer_clockevent itself.
This has the effect of breaking PR KVM, because it uses those values
in kvmppc_emulate_dec(). The symptom is guest kernels spin forever
mid-way through boot.
For now fix it by assigning back to decrementer_clockevent the mult
and shift values.
Fixes: 8b78fdb045de ("powerpc/time: Use clockevents_register_device(), fixing an issue with large decrementer") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
pcitest is currently broken due to the following compiler error
and related warning. Fix by changing the run_test() function
signature to return an integer result.
pcitest.c: In function run_test:
pcitest.c:143:9: warning: return with a value, in function
returning void
return (ret < 0) ? ret : 1 - ret; /* return 0 if test succeeded */
pcitest.c: In function main:
pcitest.c:232:9: error: void value not ignored as it ought to be
return run_test(test);
Fixes: fef31ecaaf2c ("tools: PCI: Fix compilation warnings") Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The patch 23c7b54ca1cd: "PM / devfreq: Fix devfreq_add_device() when
drivers are built as modules." leads to the following static checker
warning:
drivers/devfreq/devfreq.c:1043 governor_store()
warn: 'governor' can also be NULL
The reason is that the try_then_request_governor() function returns both
error pointers and NULL. It should just return error pointers, so fix
this by returning a ERR_PTR to the error intead of returning NULL.
Fixes: 23c7b54ca1cd ("PM / devfreq: Fix devfreq_add_device() when drivers are built as modules.") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 48402cee6889 ("ACPI / LPSS: Resume BYT/CHT I2C controllers from
resume_noirq") makes acpi_lpss_{suspend_late,resume_early}() bail early
on BYT/CHT as resume_from_noirq is set.
This means that on resume from hibernate dw_i2c_plat_resume() doesn't get
called by the restore_early callback, acpi_lpss_resume_early(). Instead it
should be called by the restore_noirq callback matching how things are done
when resume_from_noirq is set and we are doing a regular resume.
Change the restore_noirq callback to acpi_lpss_resume_noirq so that
dw_i2c_plat_resume() gets properly called when resume_from_noirq is set
and we are resuming from hibernate.
Likewise also change the poweroff_noirq callback so that
dw_i2c_plat_suspend gets called properly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202139 Fixes: 48402cee6889 ("ACPI / LPSS: Resume BYT/CHT I2C controllers from resume_noirq") Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: 4.20+ <stable@vger.kernel.org> # 4.20+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously receiver buffer auto-tuning starts after receiving
one advertised window amount of data. After the initial receiver
buffer was raised by patch a337531b942b ("tcp: up initial rmem to
128KB and SYN rwin to around 64KB"), the reciver buffer may take
too long to start raising. To address this issue, this patch lowers
the initial bytes expected to receive roughly the expected sender's
initial window.
Fixes: a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB") Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
VxLAN FDB updates are sent with the VxLAN device which is not our upper
and will therefore be ignored by current code.
Solve this by checking whether the upper device (bridge) is our upper.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com> Signed-off-by: Emil Renner Berthing <kernel@esmil.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.
Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.
This improves throughput on 2.4 GHz channels
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
mi->supported[MINSTREL_CCK_GROUP] needs to be updated
short preamble rates need to be marked as supported regardless of
whether it's currently enabled. Its state can change at any time without
a rate_update call.
Fixes: 782dda00ab8e ("mac80211: minstrel_ht: move short preamble check out of get_rate") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Zero pad private area, otherwise we expose private kernel pointer to
userspace. This patch also zeroes the tail area after the ->matchsize
and ->targetsize that results from XT_ALIGN().
While noop_qdisc.gso_skb and noop_qdisc.skb_bad_txq are not used
in other places, it seems not correct to overwrite their fields
in dev_init_scheduler_queue().
noop_qdisc is essentially a shared and read-only object, even if
it is not marked as const because of some implementation detail.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Immediately after mlxsw module is probed and lldpad started, added APP
entries are briefly in "unknown" state before becoming "pending". That's
the state that lldpad_app_wait_set() typically sees, and since there are
no pending entries at that time, it bails out. However the entries have
not been pushed to the kernel yet at that point, and thus the test case
fails.
Fix by waiting for both unknown and pending entries to disappear before
proceeding.
Fixes: d159261f3662 ("selftests: mlxsw: Add test for trust-DSCP") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change initial PWM target to 255 to prevent overheating, for example
when BMC hangs in userspace or when userspace fan control application is
not implemented yet.
Signed-off-by: Kun Yi <kunyi@google.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The three INA3221_CONFIG_MODE macros are not correctly defined here.
The MODE3-1 bits are located at BIT 2-0 according to the datasheet.
So this patch just fixes them by shifting all of them with a correct
offset. However, this isn't a crital bug fix as the driver does not
use any of them at this point.
BIOS developer guides refer to Family 15h Models 60h-6fh and Family 15h
Models 70h-7fh. So far the driver only checked for Models 60h and 70h.
However, there are now processors with other model numbers in the same
families. Example is A10-9620P family 15h model 65h. Follow the developer
guides and mask the lower 4 bit of the model number to determine the
registers to use for reading temperatures and temperature limits.
There are extraneous parantheses that are causing clang to produce a
warning so remove these.
Clean up 3 clang warnings:
equality comparison with extraneous parentheses [-Wparentheses-equality]
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Ching Huang <ching2048@areca.com.tw> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous fix made the TVC clock get muxed in on the
D-Link DIR-685 instead of giving nagging warnings of this
not working. Not good. We didn't want that, as it breaks
video.
Create a specific group for the TVC CLK, and break out
a specific GPIO group for it on the SL3516 so we can use
that line as GPIO if we don't need the TVC CLK.
Fixes: d17f477c5bc6 ("pinctrl: gemini: Mask and set properly") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently accessing various /sys/fs/orangefs files will spam the
kernel log with the following info message when the client is not
running:
[ 491.489284] sysfs_service_op_show: Client not running :-5:
Rate limit this info message to make it less spammy.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
PCI BIOS requires the BIOS area 0x0A0000-0x0FFFFFF to be mapped W+X for
various legacy reasons. When CONFIG_DEBUG_WX is enabled, this triggers the
WX warning, but this is misleading because the mapping is required and is
not a result of an accidental oversight.
Prevent the full warning when PCI BIOS is enabled and the detected WX
mapping is in the BIOS area. Just emit a pr_warn() which denotes the
fact. This is partially duplicating the info which the PCI BIOS code emits
when it maps the area as executable, but that info is not in the context of
the WX checking output.
Remove the extra %p printout in the WARN_ONCE() while at it. %pS is enough.
On at least x86 and ARM64, and as documented in the ptrace man page
a skipped system call will still cause a syscall exit ptrace stop.
Previous to this commit 32-bit ARM did not, resulting in strace
being confused when seccomp skips system calls.
This change also impacts programs that use ptrace to skip system calls.
Fixes: ad75b51459ae ("ARM: 7579/1: arch/allow a scno of -1 to not cause a SIGILL") Signed-off-by: Timothy E Baldwin <T.E.Baldwin99@members.leeds.ac.uk> Signed-off-by: Eugene Syromyatnikov <evgsyr@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Kees Cook <keescook@chromium.org> Tested-by: Eugene Syromyatnikov <evgsyr@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz> Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code was written under the assumption that the
regmap_update_bits() would mask the bits in the mask and
set the bits in the value.
It missed the points that it will not set bits in the value
unless these are also masked in the mask. Set value bits
that are not in the mask will simply be ignored.
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The priv->data->set can be NULL while flags contains GPIO_SYSCON_FEAT_OUT
and chip->set is valid pointer. This happens in case the controller uses
the default GPIO setter. Always use chip->set to access the setter to avoid
possible NULL pointer dereferencing.
XDP can modify (and resize) the Ethernet header in the packet.
There is a bug in generic-XDP, because skb->protocol and skb->pkt_type
are setup before reaching (netif_receive_)generic_xdp.
This bug was hit when XDP were popping VLAN headers (changing
eth->h_proto), as skb->protocol still contains VLAN-indication
(ETH_P_8021Q) causing invocation of skb_vlan_untag(skb), which corrupt
the packet (basically popping the VLAN again).
This patch catch if XDP changed eth header in such a way, that SKB
fields needs to be updated.
V2: on request from Song Liu, use ETH_HLEN instead of mac_len,
in __skb_push() as eth_type_trans() use ETH_HLEN in paired skb_pull_inline().
In btf_parse_hdr(), the length of the btf data header is firstly copied
from the user space to 'hdr_len' and checked to see whether it is larger
than 'btf_data_size'. If yes, an error code EINVAL is returned. Otherwise,
the whole header is copied again from the user space to 'btf->hdr'.
However, after the second copy, there is no check between
'btf->hdr->hdr_len' and 'hdr_len' to confirm that the two copies get the
same value. Given that the btf data is in the user space, a malicious user
can race to change the data between the two copies. By doing so, the user
can provide malicious data to the kernel and cause undefined behavior.
This patch adds a necessary check after the second copy, to make sure
'btf->hdr->hdr_len' has the same value as 'hdr_len'. Otherwise, an error
code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When do GC, the number of read/write sectors are determined
by max_write_pgs(see gc_rq preparation in pblk_gc_line_prepare_ws).
Due to max_write_pgs doesn't consider max hw sectors
supported by nvme controller(128K), which leads to GC
tries to read 64 * 4K in one command, and see below error
caused by pblk_bio_map_addr in function pblk_submit_read_gc.
[ 2923.005376] pblk: could not add page to bio
[ 2923.005377] pblk: could not allocate GC bio (18446744073709551604)
1.2 devices exposes their data and metadata size through the separate
identify command. Make sure that the NVMe LBA format does not override
these values.
OCSSD 2.0 defines the amount of data that the host must buffer per chunk
to guarantee reads through the geometry field mw_cunits. This value is
the base that pblk uses to determine the size of its read buffer.
Currently, this size is set to be the closes power-of-2 to mw_cunits
times the number of parallel units available to the pblk instance for
each open line (currently one). When an entry (4KB) is put in the
buffer, the L2P table points to it. As the buffer wraps up, the L2P is
updated to point to addresses on the device, thus guaranteeing mw_cunits
at a chunk level.
However, given that pblk cannot write to the device under ws_min
(normally ws_opt), there might be a window in which the buffer starts
wrapping up and updating L2P entries before the mw_cunits value in a
chunk has been surpassed.
In order not to violate the mw_cunits constrain in this case, account
for ws_opt on the read buffer creation.
When the user data counter exceeds 32 bits, the write amplification
calculation does not provide the right value. Fix this by using
div64_u64 in stead of div64.
If a line is recovered from open chunks, the memory structures for
emeta have not necessarily been properly set on line initialization.
When closing a line, make sure that emeta is consistent so that the line
can be recovered on the fast path on next reboot.
Also, remove a couple of empty lines at the end of the function.
The calculation of pblk->min_write_pgs should only use the optimal
write size attribute provided by the drive, it does not correlate to
the memory page size of the system, which can be smaller or larger
than the LBA size reported.
rqd.error is masked by the return value of pblk_submit_io_sync.
The rqd structure is then passed on to the end_io function, which
assumes that any error should lead to a chunk being marked
offline/bad. Since the pblk_submit_io_sync can fail before the
command is issued to the device, the error value maybe not correspond
to a media failure, leading to chunks being immaturely retired.
Also, the pblk_blk_erase_sync function prints an error message in case
the erase fails. Since the caller prints an error message by itself,
remove the error message in this function.
Signed-off-by: Matias Bjørling <mb@lightnvm.io> Reviewed-by: Javier González <javier@cnexlabs.com> Reviewed-by: Hans Holmberg <hans.holmberg@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Existing code returns the max of the decoded size and buffer size.
It turns out that buffer size is always greater due to hardware
alignment requirement. As a result, payload size given to client
is incorrect. This change ensures that the bytesused is assigned
to actual payload size, when available.
Shifting the u8 value[3] by an int can lead to sign-extension
overflow. For example, if value[3] is 0xff and the shift is 24 then it
is promoted to int and then the top bit is sign-extended so that all
upper 32 bits are set. Fix this by casting value[3] to a u32 before
the shift.
Detected by CoverityScan, CID#1016522 ("Unintended sign extension")
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Flushing the workqueue can cause operations to happen which might
call gfs2_log_reserve(), or get stuck waiting for locks taken by such
operations. gfs2_log_reserve() can io_schedule(). If this happens, it
will never wake because the only thing which can wake it is gfs2_logd()
which was already stopped.
This causes umount of a gfs2 filesystem to wedge permanently if, for
example, the umount immediately follows a large delete operation.
When this occured, the following stack trace was obtained from the
umount command
Signed-off-by: Tim Smith <tim.smith@citrix.com> Signed-off-by: Mark Syms <mark.syms@citrix.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In isif_probe(), there is a while loop to get the ISIF base address and
linearization table0 and table1 address. In the loop body, the function
platform_get_resource() is called to get the resource. If
platform_get_resource() returns NULL, the loop is terminated and the
execution goes to 'fail_nobase_res'. Suppose the loop is terminated at the
first iteration because platform_get_resource() returns NULL and the
execution goes to 'fail_nobase_res'. Given that there is another while loop
at 'fail_nobase_res' and i equals to 0, one iteration of the second while
loop will be executed. However, the second while loop does not check the
return value of platform_get_resource(). This can cause a NULL pointer
dereference bug if the return value is a NULL pointer.
This patch avoids the above issue by adding a check in the second while
loop after the call to platform_get_resource().
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a child device like touchscreen is wakeup capable, then keep ADC
interface on, so that a touching resistive screen will generate wakeup
event to the system.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/video/backlight/lm3639_bl.c:403:14: warning: address of
'pchip->cdev_torch' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_torch)
~~ ~~~~~~~^~~~~~~~~~
drivers/video/backlight/lm3639_bl.c:405:14: warning: address of
'pchip->cdev_flash' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_flash)
~~ ~~~~~~~^~~~~~~~~~
2 warnings generated.
These statements have been present since 2012, introduced by
commit 0f59858d5119 ("backlight: add new lm3639 backlight
driver"). Given that they have been called unconditionally since
then presumably without any issues, removing the always true if
statements to fix the warnings without any real world changes.
Link: https://github.com/ClangBuiltLinux/linux/issues/119 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Lianbo reported a build error with a particular 32-bit config, see Link
below for details.
Provide a weak copy_oldmem_page_encrypted() function which architectures
can override, in the same manner other functionality in that file is
supplied.
Kasan instrumentation adds "store" check for variables marked as
modified by inline assembly. With user pointers containing addresses
from another address space this produces false positives.
User space access functions are wrapped by manually instrumented
functions in kasan common code, which should be sufficient to catch
errors. So, we just disable uaccess.o instrumentation altogether.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instrumented C code cannot run without the kasan shadow area. Exempt
source code files from kasan which are running before / used during
kasan initialization.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.
The CBM overlap test is used to manage the allocations of RDT resources
where overlap is possible between resource groups. When a resource group
is in exclusive mode then there should be no overlap between resource
groups.
The current overlap test only considers overlap between the same
resources, for example, that usage of a RDT_RESOURCE_L2DATA resource
in one resource group does not overlap with usage of a RDT_RESOURCE_L2DATA
resource in another resource group. The problem with this is that it
allows overlap between a RDT_RESOURCE_L2DATA resource in one resource
group with a RDT_RESOURCE_L2CODE resource in another resource group -
even if both resource groups are in exclusive mode. This is a problem
because even though these appear to be different resources they end up
sharing the same underlying hardware and thus does not fulfill the
user's request for exclusive use of hardware resources.
Fix this by including the CDP peer (if there is one) in every CBM
overlap test. This does not impact the overlap between resources
within the same exclusive resource group that is allowed.
Introduce a utility that, when provided with a RDT resource and an
instance of this RDT resource (a RDT domain), would return pointers to
the RDT resource and RDT domain that share the same hardware. This is
specific to the CDP resources that share the same hardware.
For example, if a pointer to the RDT_RESOURCE_L2DATA resource (struct
rdt_resource) and a pointer to an instance of this resource (struct
rdt_domain) is provided, then it will return a pointer to the
RDT_RESOURCE_L2CODE resource as well as the specific instance that
shares the same hardware as the provided rdt_domain.
This utility is created in support of the "exclusive" resource group
mode where overlap of resource allocation between resource groups need
to be avoided. The overlap test need to consider not just the matching
resources, but also the resources that share the same hardware.
Temporarily mark it as unused in support of patch testing to avoid
compile warnings until it is used.
Some SPI controllers can't write nor->page_size bytes in a single step
because their TX FIFO is too small, but when that happens we should
make sure a WRITE_EN command before each write access and READ_SR command
after each write access is issued.
The core is already taking care of that, so all we have to do here is
return the actual number of bytes that were written during the
spi_mem_exec_op() operation.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/media/pci/cx18/cx18-driver.c:1255:23: warning: address of
'cx->streams[i].video_dev' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&cx->streams[i].video_dev)
~~ ~~~~~~~~~~~~~~~^~~~~~~~~
1 warning generated.
Check whether v4l2_dev is null, not the address, so that the statement
doesn't fire all the time. This check has been present since 2009,
introduced by commit 21a278b85d3c ("V4L/DVB (11619): cx18: Simplify the
work handler for outgoing mailbox commands")
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns that mlxplat_mlxcpld_msn201x_items is not going to be
emitted in the final assembly because it's only used in ARRAY_SIZE right
now, which is a compile time evaluation since the array's size is known.
drivers/platform/x86/mlx-platform.c:555:32: warning: variable
'mlxplat_mlxcpld_msn201x_items' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
static struct mlxreg_core_item mlxplat_mlxcpld_msn201x_items[] = {
^
1 warning generated.
It appears this was a copy and paste mistake from when this item was
first added. Use the definition in mlxplat_mlxcpld_msn201x_data so that
Clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/141 Fixes: a49a41482f61 ("platform/x86: mlx-platform: Add support for new msn201x system type") Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
UUIDs are considered as metadata. __uuid_write should add the number
of buckets (in sectors) written to disk to ca->meta_sectors_written.
Currently only 1 bucket is used in uuid write.
Steps to test:
1) create a fresh backing device and a fresh cache device separately.
The backing device didn't attach to any cache set.
2) cd /sys/block/<cache device>/bcache
cat metadata_written // record the output value
cat bucket_size
3) attach the backing device to cache set
4) cat metadata_written
The output value is almost the same as the value in step 2
before the change.
After the change, the value is bigger about 1 bucket size.
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com> Reviewed-by: Tang Junhui <tang.junhui.linux@gmail.com> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The framebuffer options and devices menu is unintentionally split
or broken because some items in it do not depend on FB (including
several under omap and mmp).
Fix this by moving FB_CMDLINE, FB_NOTIFY, and FB_CLPS711X_OLD to
just before the FB Kconfig symbol definition and by moving the
omap, omap2, and mmp menus to last, following FB_SM712.
Also, the FB_VIA dependencies are duplicated by both being inside
an "if FB_VIA/endif" block and "depends on FB_VIA", so drop the
"depends on FB_VIA" lines since they are redundant.
Fixes: ea6763c104c9 ("video/fbdev: Always built-in video= cmdline parsing") Fixes: 5ec9653806ba ("fbdev: Make fb-notify a no-op if CONFIG_FB=n") Fixes: ef74d46a4ef3 ("video: clps711x: Add new Cirrus Logic CLPS711X framebuffer driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I'm not sure why the code assumes that only the first put_user() needs
an access_ok() check. I have made all the put_user() and get_user()
calls checked.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Mathieu Malaterre <malat@debian.org> Cc: Peter Malone <peter.malone@gmail.com>, Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
