For IDP variant, GPIO 20/21 is used by camera use case and camera
driver is not able acquire these GPIOs as it is acquired by UART5
driver as RTS/CTS pin.
UART5 is designed for debug UART for all the board variants of the
sc7280 chipset and RTS/CTS configuration is not required for debug
uart usecase.
Remove CTS/RTS configuration for UART5 instance and change compatible
string to debug UART.
Remove overwriting compatible property from individual target specific
file as it is not required.
The critical alarm bit for the local temperature sensor (temp1) is in
bit 7 of register 0x45 (not bit 6), and the critical alarm bit for remote
temperature sensor 7 (temp8) is in bit 6 (not bit 7).
This only affects MAX6581 since all other chips supported by this driver
do not support those critical alarms.
The hardware only supports a single period length for both PWM outputs. So
atmel_tcb_pwm_config() checks the configuration of the other output if it's
compatible with the currently requested setting. The register values are
then actually updated in atmel_tcb_pwm_enable(). To make this race free
the lock must be held during the whole process, so grab the lock in
.apply() instead of individually in atmel_tcb_pwm_disable() and
atmel_tcb_pwm_enable() which then also covers atmel_tcb_pwm_config().
To simplify handling, use the guard helper to let the compiler care for
unlocking. Otherwise unlocking would be more difficult as there is more
than one exit path in atmel_tcb_pwm_apply().
Allocated canvases may not be released on the error exit path of
meson_drv_bind_master(), leading to resource leaking. Rewrite exit path
to release canvases on error.
If we fail to call nvme_auth_augmented_challenge, or fail to kmalloc
for shash, we should free the memory allocation for challenge, so add
err path out_free_challenge to fix the memory leak.
Fixes: 7a277c37d352 ("nvmet-auth: Diffie-Hellman key exchange support") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 83cfac95c018 ("genirq: Allow interrupts to be excluded from
/proc/interrupts") is to avoid IPIs appear twice in /proc/interrupts.
But the commit 331a1b3a836c ("arm64: smp: Add arch support for backtrace
using pseudo-NMI") and commit 2f5cd0c7ffde("arm64: kgdb: Implement
kgdb_roundup_cpus() to enable pseudo-NMI roundup") set CPU_BACKTRACE and
KGDB_ROUNDUP IPIs "IRQ_HIDDEN" flag but not show them in
arch_show_interrupts(), which cause the interrupt kstat_irqs accounting
is missing in display.
In the process of adding support for shared IRQ pins, a scenario
was accidentally created where adv7511_irq_process returned
prematurely causing the EDID to fail randomly.
Since the interrupt handler is broken up into two main helper functions,
update both of them to treat the helper functions as IRQ handlers. These
IRQ routines process their respective tasks as before, but if they
determine that actual work was done, mark the respective IRQ status
accordingly, and delay the check until everything has been processed.
This should guarantee the helper functions don't return prematurely
while still returning proper values of either IRQ_HANDLED or IRQ_NONE.
Reported-by: Liu Ying <victor.liu@nxp.com> Fixes: f3d9683346d6 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins") Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Liu Ying <victor.liu@nxp.com> # i.MX8MP EVK ADV7535 EDID retrieval w/o IRQ Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240630221931.1650565-1-aford173@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
V3: Remove unnecessary declaration of ret by evaluating the return
code of regmap_read directly.
V2: Fix uninitialized cec_status
Cut back a little on error handling to return either IRQ_NONE or
IRQ_HANDLED. Signed-off-by: Sasha Levin <sashal@kernel.org>
When the state changes from enabled to disabled, polarity, duty_cycle
and period are not configured in hardware and TIM_CCER_CCxE is just
cleared. However if the state changes from one disabled state to
another, all parameters are written to hardware because the early exit
from stm32_pwm_apply() is only taken if the pwm is currently enabled.
LTC2991_T_INT_CH_NR is 4. The st->temp_en[] array has LTC2991_MAX_CHANNEL
(4) elements. Thus if "channel" is equal to LTC2991_T_INT_CH_NR then we
have read one element beyond the end of the array. Flip the conditions
around so that we check if "channel" is valid before using it as an array
index.
When handling an IO request, MD checks if a reshape is currently
happening, and if so, where the IO sector is in relation to the reshape
progress. MD uses conf->reshape_progress for both of these tasks. When
the reshape finishes, conf->reshape_progress is set to MaxSector. If
this occurs after MD checks if the reshape is currently happening but
before it calls ahead_of_reshape(), then ahead_of_reshape() will end up
comparing the IO sector against MaxSector. During a backwards reshape,
this will make MD think the IO sector is in the area not yet reshaped,
causing it to use the previous configuration, and map the IO to the
sector where that data was before the reshape.
This bug can be triggered by running the lvm2
lvconvert-raid-reshape-linear_to_raid6-single-type.sh test in a loop,
although it's very hard to reproduce.
Fix this by factoring the code that checks where the IO sector is in
relation to the reshape out to a helper called get_reshape_loc(),
which reads reshape_progress and reshape_safe while holding the
device_lock, and then rechecks if the reshape has finished before
calling ahead_of_reshape with the saved values.
Also use the helper during the REQ_NOWAIT check to see if the location
is inside of the reshape region.
Fixes: fef9c61fdfabf ("md/raid5: change reshape-progress measurement to cope with reshaping backwards.") Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20240702151802.1632010-1-bmarzins@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 90f5f7ad4f38 ("md: Wait for md_check_recovery before attempting
device removal.") explained in the commit message that failed device
must be reomoved from the personality first by md_check_recovery(),
before it can be removed from the array. That's the reason the commit
add the code to wait for MD_RECOVERY_NEEDED.
However, this is not the case now, because remove_and_add_spares() is
called directly from hot_remove_disk() from ioctl path, hence failed
device(marked faulty) can be removed from the personality by ioctl.
On the other hand, the commit introduced a performance problem that
if MD_RECOVERY_NEEDED is set and the array is not running, ioctl will
wait for 5s before it can return failure to user.
Since the waiting is not needed now, fix the problem by removing the
waiting.
Fixes: 90f5f7ad4f38 ("md: Wait for md_check_recovery before attempting device removal.") Reported-by: Mateusz Kusiak <mateusz.kusiak@linux.intel.com> Closes: https://lore.kernel.org/all/814ff6ee-47a2-4ba0-963e-cf256ee4ecfa@linux.intel.com/ Signed-off-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20240627112321.3044744-1-yukuai1@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the user has requested a counting threshold for the CPU cycles event,
then the fixed cycle counter can't be assigned as it lacks threshold
support. Currently, the thresholds will work or not randomly depending
on which counter the event is assigned.
While using thresholds for CPU cycles doesn't make much sense, it can be
useful for testing purposes.
Fixes: 816c26754447 ("arm64: perf: Add support for event counting threshold") Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/r/20240626-arm-pmu-3-9-icntr-v2-1-c9784b4f4065@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that info->sector_size and info->physical_sector_size are set
before the call to blkif_set_queue_limits by doing away with the
local variables and arguments that propagate them.
Thanks to Marek Marczykowski-Górecki and Jürgen Groß for root causing
the issue.
The current tag reservation code is based on a misunderstanding of the
meaning of data->shallow_depth. Fix the tag reservation code as follows:
* By default, do not reserve any tags for synchronous requests because
for certain use cases reserving tags reduces performance. See also
Harshit Mogalapalli, [bug-report] Performance regression with fio
sequential-write on a multipath setup, 2024-03-07
(https://lore.kernel.org/linux-block/5ce2ae5d-61e2-4ede-ad55-551112602401@oracle.com/)
* Reduce min_shallow_depth to one because min_shallow_depth must be less
than or equal any shallow_depth value.
* Scale dd->async_depth from the range [1, nr_requests] to [1,
bits_per_sbitmap_word].
Cc: Christoph Hellwig <hch@lst.de> Cc: Damien Le Moal <dlemoal@kernel.org> Cc: Zhiguo Niu <zhiguo.niu@unisoc.com> Fixes: 07757588e507 ("block/mq-deadline: Reserve 25% of scheduler tags for synchronous requests") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20240509170149.7639-3-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the comments on fan is disabled, we change to manual mode
and set the duty cycle to 0.
For setting the duty cycle part, the register is wrong. Fix it.
Fixes: 1c301fc5394f ("hwmon: Add a driver for the ADT7475 hardware monitoring chip") Signed-off-by: Wayne Tung <chineweff@gmail.com> Link: https://lore.kernel.org/r/20240701073252.317397-1-chineweff@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
An UAF can happen when /proc/cpuset is read as reported in [1].
This can be reproduced by the following methods:
1.add an mdelay(1000) before acquiring the cgroup_lock In the
cgroup_path_ns function.
2.$cat /proc/<pid>/cpuset repeatly.
3.$mount -t cgroup -o cpuset cpuset /sys/fs/cgroup/cpuset/
$umount /sys/fs/cgroup/cpuset/ repeatly.
The race that cause this bug can be shown as below:
When the cpuset is initialized, the root node top_cpuset.css.cgrp
will point to &cgrp_dfl_root.cgrp. In cgroup v1, the mount operation will
allocate cgroup_root, and top_cpuset.css.cgrp will point to the allocated
&cgroup_root.cgrp. When the umount operation is executed,
top_cpuset.css.cgrp will be rebound to &cgrp_dfl_root.cgrp.
The problem is that when rebinding to cgrp_dfl_root, there are cases
where the cgroup_root allocated by setting up the root for cgroup v1
is cached. This could lead to a Use-After-Free (UAF) if it is
subsequently freed. The descendant cgroups of cgroup v1 can only be
freed after the css is released. However, the css of the root will never
be released, yet the cgroup_root should be freed when it is unmounted.
This means that obtaining a reference to the css of the root does
not guarantee that css.cgrp->root will not be freed.
Fix this problem by using rcu_read_lock in proc_cpuset_show().
As cgroup_root is kfree_rcu after commit d23b5c577715
("cgroup: Make operations on the cgroup root_list RCU safe"),
css->cgroup won't be freed during the critical section.
To call cgroup_path_ns_locked, css_set_lock is needed, so it is safe to
replace task_get_css with task_css.
The direct-call syscall dispatch function doesn't know that the exit()
and exit_group() syscall handlers don't return, so the call sites aren't
optimized accordingly.
Fix that by marking the exit syscall declarations __noreturn.
Fixes the following warnings:
vmlinux.o: warning: objtool: x64_sys_call+0x2804: __x64_sys_exit() is missing a __noreturn annotation
vmlinux.o: warning: objtool: ia32_sys_call+0x29b6: __ia32_sys_exit_group() is missing a __noreturn annotation
Fixes: 1e3ad78334a6 ("x86/syscall: Don't force use of indirect calls for system calls") Closes: https://lkml.kernel.org/lkml/6dba9b32-db2c-4e6d-9500-7a08852f17a3@paulmck-laptop Reported-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Tested-by: Paul E. McKenney <paulmck@kernel.org> Link: https://lore.kernel.org/r/5d8882bc077d8eadcc7fd1740b56dfb781f12288.1719381528.git.jpoimboe@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
iosf_mbi_pci_{read,write}_mdr() use pci_{read,write}_config_dword()
that return PCIBIOS_* codes but functions also return -ENODEV which are
not compatible error codes. As neither of the functions are related to
PCI read/write functions, they should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning it.
Fixes: 46184415368a ("arch: x86: New MailBox support driver for Intel SOC's") Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/r/20240527125538.13620-4-ilpo.jarvinen@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
xen_pcifront_enable_irq() uses pci_read_config_byte() that returns
PCIBIOS_* codes. The error handling, however, assumes the codes are
normal errnos because it checks for < 0.
xen_pcifront_enable_irq() also returns the PCIBIOS_* code back to the
caller but the function is used as the (*pcibios_enable_irq) function
which should return normal errnos.
Convert the error check to plain non-zero check which works for
PCIBIOS_* return codes and convert the PCIBIOS_* return code using
pcibios_err_to_errno() into normal errno before returning it.
intel_mid_pci_irq_enable() uses pci_read_config_byte() that returns
PCIBIOS_* codes. The error handling, however, assumes the codes are
normal errnos because it checks for < 0.
intel_mid_pci_irq_enable() also returns the PCIBIOS_* code back to the
caller but the function is used as the (*pcibios_enable_irq) function
which should return normal errnos.
Convert the error check to plain non-zero check which works for
PCIBIOS_* return codes and convert the PCIBIOS_* return code using
pcibios_err_to_errno() into normal errno before returning it.
Fixes: 5b395e2be6c4 ("x86/platform/intel-mid: Make IRQ allocation a bit more flexible") Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20240527125538.13620-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
x86_of_pci_irq_enable() returns PCIBIOS_* code received from
pci_read_config_byte() directly and also -EINVAL which are not
compatible error types. x86_of_pci_irq_enable() is used as
(*pcibios_enable_irq) function which should not return PCIBIOS_* codes.
Convert the PCIBIOS_* return code from pci_read_config_byte() into
normal errno using pcibios_err_to_errno().
Fixes: 96e0a0797eba ("x86: dtb: Add support for PCI devices backed by dtb nodes") Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/r/20240527125538.13620-1-ilpo.jarvinen@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 181c8e091aae ("cgroup/cpuset: Introduce remote partition"),
a remote partition can be created underneath a non-partition root cpuset
as long as its exclusive_cpus are set to distribute exclusive CPUs down
to its children. The generate_sched_domains() function, however, doesn't
take into account this new behavior and hence will fail to create the
sched domain needed for a remote root (non-isolated) partition.
There are two issues related to remote partition support. First of
all, generate_sched_domains() has a fast path that is activated if
root_load_balance is true and top_cpuset.nr_subparts is non-zero. The
later condition isn't quite correct for remote partitions as nr_subparts
just shows the number of local child partitions underneath it. There
can be no local child partition under top_cpuset even if there are
remote partitions further down the hierarchy. Fix that by checking
for subpartitions_cpus which contains exclusive CPUs allocated to both
local and remote partitions.
Secondly, the valid partition check for subtree skipping in the csa[]
generation loop isn't enough as remote partition does not need to
have a partition root parent. Fix this problem by breaking csa[] array
generation loop of generate_sched_domains() into v1 and v2 specific parts
and checking a cpuset's exclusive_cpus before skipping its subtree in
the v2 case.
Also simplify generate_sched_domains() for cgroup v2 as only
non-isolating partition roots should be included in building the cpuset
array and none of the v1 scheduling attributes other than a different
way to create an isolated partition are supported.
If only isolated partitions are being created underneath the cgroup root,
there will only be one sched domain with top_cpuset.effective_cpus. We can
skip the unnecessary sched domains scanning code and save some cycles.
io_probe checks io_issue_def->not_supported, but we never really set
that field, as we mark non-supported functions through a specific ->prep
handler. This means we end up returning IO_URING_OP_SUPPORTED, even for
disabled operations. Fix it by just checking the prep handler itself.
Fixes: 66f4af93da57 ("io_uring: add support for probing opcodes") Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de> Link: https://lore.kernel.org/r/20240619020620.5301-2-krisman@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
dm_revalidate_zones() is called from dm_set_zone_restrictions() when the
mapped device queue limits are not yet set. However,
dm_revalidate_zones() calls blk_revalidate_disk_zones() and this
function consults and modifies the mapped device queue limits. Thus,
currently, blk_revalidate_disk_zones() operates on limits that are not
yet initialized.
Fix this by moving the call to dm_revalidate_zones() out of
dm_set_zone_restrictions() and into dm_table_set_restrictions() after
executing queue_limits_set().
To further cleanup dm_set_zones_restrictions(), the message about the
type of zone append (native or emulated) is also moved inside
dm_revalidate_zones().
Fixes: 1c0e720228ad ("dm: use queue_limits_set") Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Benjamin Marzinski <bmarzins@redhat.com> Reviewed-by: Niklas Cassel <cassel@kernel.org> Link: https://lore.kernel.org/r/20240611023639.89277-3-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Metadata added by bio_integrity_prep is using plain kmalloc, which leads
to random kernel memory being written media. For PI metadata this is
limited to the app tag that isn't used by kernel generated metadata,
but for non-PI metadata the entire buffer leaks kernel memory.
Fix this by adding the __GFP_ZERO flag to allocations for writes.
Fixes: 7ba1ba12eeef ("block: Block layer data integrity support") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Kanchan Joshi <joshi.k@samsung.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Link: https://lore.kernel.org/r/20240613084839.1044015-2-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Discard and Write Zeroes are different operation and implemented
by different fallocate opcodes for ubd. If one fails the other one
can work and vice versa.
Split the code to disable the operations in ubd_handler to only
disable the operation that actually failed.
Fixes: 50109b5a03b4 ("um: Add support for DISCARD in the UBD Driver") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Link: https://lore.kernel.org/r/20240531074837.1648501-3-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of a separate handler function that leaves no work in the
interrupt hanler itself, split out a per-request end I/O helper and
clean up the coding style and variable naming while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Link: https://lore.kernel.org/r/20240531074837.1648501-2-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 31ade7d4fdcf ("ubd: untagle discard vs write zeroes not support handling") Signed-off-by: Sasha Levin <sashal@kernel.org>
The core md code calls the ->free method which already frees conf.
Fixes: 07f1a6850c5d ("md/raid1: fail run raid1 array when active disk less than one") Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20240604172607.3185916-3-hch@lst.de Signed-off-by: Sasha Levin <sashal@kernel.org>
Deadlock occurs when mddev is being suspended while some flush bio is in
progress. It is a complex issue.
T1. the first flush is at the ending stage, it clears 'mddev->flush_bio'
and tries to submit data, but is blocked because mddev is suspended
by T4.
T2. the second flush sets 'mddev->flush_bio', and attempts to queue
md_submit_flush_data(), which is already running (T1) and won't
execute again if on the same CPU as T1.
T3. the third flush inc active_io and tries to flush, but is blocked because
'mddev->flush_bio' is not NULL (set by T2).
T4. mddev_suspend() is called and waits for active_io dec to 0 which is inc
by T3.
The root issue is non-atomic inc/dec of active_io during flush process.
active_io is dec before md_submit_flush_data is queued, and inc soon
after md_submit_flush_data() run.
md_flush_request
active_io + 1
submit_flushes
active_io - 1
md_submit_flush_data
md_handle_request
active_io + 1
make_request
active_io - 1
If active_io is dec after md_handle_request() instead of within
submit_flushes(), make_request() can be called directly intead of
md_handle_request() in md_submit_flush_data(), and active_io will
only inc and dec once in the whole flush process. Deadlock will be
fixed.
Additionally, the only difference between fixing the issue and before is
that there is no return error handling of make_request(). But after
previous patch cleaned md_write_start(), make_requst() only return error
in raid5_make_request() by dm-raid, see commit 41425f96d7aa ("dm-raid456,
md/raid456: fix a deadlock for dm-raid456 while io concurrent with
reshape)". Since dm always splits data and flush operation into two
separate io, io size of flush submitted by dm always is 0, make_request()
will not be called in md_submit_flush_data(). To prevent future
modifications from introducing issues, add WARN_ON to ensure
make_request() no error is returned in this context.
When RCU-TASKS-TRACE pre-gp takes a snapshot of the current task running
on all online CPUs, no explicit ordering synchronizes properly with a
context switch. This lack of ordering can permit the new task to miss
pre-grace-period update-side accesses. The following diagram, courtesy
of Paul, shows the possible bad scenario:
Either r0==TASK_B or r1==1 is needed but neither is guaranteed.
One possible solution to solve this is to wait for an RCU grace period
at the beginning of the RCU-tasks-trace grace period before taking the
current tasks snaphot. However this would introduce large additional
latencies to RCU-tasks-trace grace periods.
Another solution is to lock the target runqueue while taking the current
task snapshot. This ensures that the update side sees the latest context
switch and subsequent context switches will see the pre-grace-period
update side accesses.
This commit therefore adds runqueue locking to cpu_curr_snapshot().
Fixes: e386b6725798 ("rcu-tasks: Eliminate RCU Tasks Trace IPIs to online CPUs") Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 598afa050403 ("kbuild: warn objects shared among multiple modules")
was added to track down cases where the same object is linked into
multiple modules. This can cause serious problems if some modules are
builtin while others are not.
That test triggers this warning:
scripts/Makefile.build:236: drivers/edac/Makefile: skx_common.o is added to multiple modules: i10nm_edac skx_edac
Make this a separate module instead.
[Tony: Added more background details to commit message]
Fixes: d4dc89d069aa ("EDAC, i10nm: Add a driver for Intel 10nm server processors") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Tony Luck <tony.luck@intel.com> Link: https://lore.kernel.org/all/20240529095132.1929397-1-arnd@kernel.org/ Signed-off-by: Sasha Levin <sashal@kernel.org>
The SPI "hard" controller in PolarFire SoC has eight CS lines, but only
one CS line is wired. When the 'num-cs' property is not specified in
the device tree, the driver defaults to the MAX_CS value, which has
been fixed to 1 to match the hardware configuration; however, when the
'num-cs' property is explicitly defined in the device tree, it
overrides the default value.
Fixes: 9ac8d17694b6 ("spi: add support for microchip fpga spi controllers") Signed-off-by: Prajna Rajendra Kumar <prajna.rajendrakumar@microchip.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Link: https://msgid.link/r/20240514104508.938448-3-prajna.rajendrakumar@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cited commit missed to check against the validity of the frame length
in the tap_get_user_xdp() path, which could cause a corrupted skb to be
sent downstack. Even before the skb is transmitted, the
tap_get_user_xdp()-->skb_set_network_header() may assume the size is more
than ETH_HLEN. Once transmitted, this could either cause out-of-bound
access beyond the actual length, or confuse the underlayer with incorrect
or inconsistent header length in the skb metadata.
In the alternative path, tap_get_user() already prohibits short frame which
has the length less than Ethernet header size from being transmitted.
This is to drop any frame shorter than the Ethernet header size just like
how tap_get_user() does.
CVE: CVE-2024-41090 Link: https://lore.kernel.org/netdev/1717026141-25716-1-git-send-email-si-wei.liu@oracle.com/ Fixes: 0efac27791ee ("tap: accept an array of XDP buffs through sendmsg()") Cc: stable@vger.kernel.org Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com> Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Jason Wang <jasowang@redhat.com> Link: https://patch.msgid.link/20240724170452.16837-2-dongli.zhang@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cited commit missed to check against the validity of the frame length
in the tun_xdp_one() path, which could cause a corrupted skb to be sent
downstack. Even before the skb is transmitted, the
tun_xdp_one-->eth_type_trans() may access the Ethernet header although it
can be less than ETH_HLEN. Once transmitted, this could either cause
out-of-bound access beyond the actual length, or confuse the underlayer
with incorrect or inconsistent header length in the skb metadata.
In the alternative path, tun_get_user() already prohibits short frame which
has the length less than Ethernet header size from being transmitted for
IFF_TAP.
This is to drop any frame shorter than the Ethernet header size just like
how tun_get_user() does.
CVE: CVE-2024-41091 Inspired-by: https://lore.kernel.org/netdev/1717026141-25716-1-git-send-email-si-wei.liu@oracle.com/ Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()") Cc: stable@vger.kernel.org Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Jason Wang <jasowang@redhat.com> Link: https://patch.msgid.link/20240724170452.16837-3-dongli.zhang@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I wrote commit 3cad1bc01041 ("filelock: Remove locks reliably when
fcntl/close race is detected"), I missed that there are two copies of the
code I was patching: The normal version, and the version for 64-bit offsets
on 32-bit kernels.
Thanks to Greg KH for stumbling over this while doing the stable
backport...
Apply exactly the same fix to the compat path for 32-bit kernels.
When the UMP Endpoint is configured with static blocks, the block
configuration will never change, hence the unused ports will be
unchanged as well. Creating sequencer ports for those unused ports
is simply useless, and it might be rather confusing for users.
The idea behind the inactive ports was for allowing connections
from/to ports that can become usable later, but this will never
happen for inactive groups in static blocks.
Let's change the sequencer UMP binding to skip those unused ports when
the UMP EP is with static blocks.
When suspended, the DMA channel may enter PAUSE state if dmaengine_pause()
is supported by DMA.
At this state, dmaengine_synchronize() should not be called, otherwise
the DMA channel can't be resumed successfully.
For Gen-1 targets like SM6115, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for SM6115 to mitigate this issue.
For Gen-1 targets like SDM845, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for SDM845 to mitigate this issue.
For Gen-1 targets like IPQ8074, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for IPQ8074 to mitigate this issue.
For Gen-1 targets like SDM630, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for SDM630 to mitigate this issue.
For Gen-1 targets like IPQ6018, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for IPQ6018 to mitigate this issue.
For Gen-1 targets like MSM8998, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for MSM8998 to mitigate this issue.
For Gen-1 targets like SM6350, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for SM6350 to mitigate this issue.
For Gen-1 targets like MSM8996, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for MSM8996 to mitigate this issue.
On the Qualcomm RB2 platform the I2C bus connected to the LT9611UXC
bridge under some circumstances can go into a state when all transfers
timeout. This causes both issues with fetching of EDID and with
updating of the bridge's firmware. While we are debugging the issue,
switch corresponding I2C bus to use i2c-gpio driver. While using
i2c-gpio no communication issues are observed.
This patch is asusmed to be a temporary fix, so it is implemented in a
non-intrusive manner to simply reverting it later.
On the Qualcomm RB1 platform the I2C bus connected to the LT9611UXC
bridge under some circumstances can go into a state when all transfers
timeout. This causes both issues with fetching of EDID and with
updating of the bridge's firmware. While we are debugging the issue,
switch corresponding I2C bus to use i2c-gpio driver. While using
i2c-gpio no communication issues are observed.
This patch is asusmed to be a temporary fix, so it is implemented in a
non-intrusive manner to simply reverting it later.
On SC7280, in host mode, it is observed that stressing out controller
results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instances in park mode for SC7280 to mitigate this issue.
Reported-by: Doug Anderson <dianders@google.com> Cc: stable@vger.kernel.org Fixes: bb9efa59c665 ("arm64: dts: qcom: sc7280: Add USB related nodes") Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20240604060659.1449278-3-quic_kriskura@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SC7180, in host mode, it is observed that stressing out controller
results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instances in park mode for SC7180 to mitigate this issue.
Reported-by: Doug Anderson <dianders@google.com> Cc: stable@vger.kernel.org Fixes: 0b766e7fe5a2 ("arm64: dts: qcom: sc7180: Add USB related nodes") Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20240604060659.1449278-2-quic_kriskura@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samsung Galaxy Book Pro 360 (13" 2022 NT935QDB-KC71S) with codec SSID
144d:c1a4 requires the same workaround to enable the speaker amp
as other Samsung models with the ALC298 codec.
The MIDI2 gadget driver handled the default MIDI protocol version
incorrectly due to the confusion of the protocol version passed via
configfs (either 1 or 2) and UMP protocol bits (0x100 / 0x200).
As a consequence, the default protocol always resulted in MIDI1.
This patch addresses the misunderstanding of the protocol handling.
This adds sanity checks for ff offset. There is a check
on rt->first_free at first, but walking through by ff
without any check. If the second ff is a large offset.
We may encounter an out-of-bound read.
Signed-off-by: lei lu <llfamsec@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check before visiting the members of ea to
make sure each ea stays within the ealist.
Signed-off-by: lei lu <llfamsec@gmail.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds sanity checks for ocfs2_dir_entry to make sure all members of
ocfs2_dir_entry don't stray beyond valid memory region.
Link: https://lkml.kernel.org/r/20240626104433.163270-1-llfamsec@gmail.com Signed-off-by: lei lu <llfamsec@gmail.com> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no support for HWPOISON, MEMORY_FAILURE, or ARCH_HAS_COPY_MC on
s390. Therefore we do not expect to see VM_FAULT_HWPOISON in
do_exception().
However, since commit af19487f00f3 ("mm: make PTE_MARKER_SWAPIN_ERROR more
general"), it is possible to see VM_FAULT_HWPOISON in combination with
PTE_MARKER_POISONED, even on architectures that do not support HWPOISON
otherwise. In this case, we will end up on the BUG() in do_exception().
Fix this by treating VM_FAULT_HWPOISON the same as VM_FAULT_SIGBUS, similar
to x86 when MEMORY_FAILURE is not configured. Also print unexpected fault
flags, for easier debugging.
Note that VM_FAULT_HWPOISON_LARGE is not expected, because s390 cannot
support swap entries on other levels than PTE level.
Cc: stable@vger.kernel.org # 6.6+ Fixes: af19487f00f3 ("mm: make PTE_MARKER_SWAPIN_ERROR more general") Reported-by: Yunseong Kim <yskelg@gmail.com> Tested-by: Yunseong Kim <yskelg@gmail.com> Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Message-ID: <20240715180416.3632453-1-gerald.schaefer@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iwlwifi wireless driver registers a thermal zone that is only needed
when the network interface handled by it is up and it wants that thermal
zone to be effectively ignored by the core otherwise.
Before commit a8a261774466 ("thermal: core: Call monitor_thermal_zone()
if zone temperature is invalid") that could be achieved by returning
an error code from the thermal zone's .get_temp() callback because the
core did not really handle errors returned by it almost at all.
However, commit a8a261774466 made the core attempt to recover from the
situation in which the temperature of a thermal zone cannot be
determined due to errors returned by its .get_temp() and is always
invalid from the core's perspective.
That was done because there are thermal zones in which .get_temp()
returns errors to start with due to some difficulties related to the
initialization ordering, but then it will start to produce valid
temperature values at one point.
Unfortunately, the simple approach taken by commit a8a261774466,
which is to poll the thermal zone periodically until its .get_temp()
callback starts to return valid temperature values, is at odds with
the special thermal zone in iwlwifi in which .get_temp() may always
return an error because its network interface may always be down. If
that happens, every attempt to invoke the thermal zone's .get_temp()
callback resulting in an error causes the thermal core to print a
dev_warn() message to the kernel log which is super-noisy.
To address this problem, make the core handle the case in which
.get_temp() returns 0, but the temperature value returned by it
is not actually valid, in a special way. Namely, make the core
completely ignore the invalid temperature value coming from
.get_temp() in that case, which requires folding in
update_temperature() into its caller and a few related changes.
On the iwlwifi side, modify iwl_mvm_tzone_get_temp() to return 0
and put THERMAL_TEMP_INVALID into the temperature return memory
location instead of returning an error when the firmware is not
running or it is not of the right type.
Also, to clearly separate the handling of invalid temperature
values from the thermal zone initialization, introduce a special
THERMAL_TEMP_INIT value specifically for the latter purpose.
Fixes: a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid") Closes: https://lore.kernel.org/linux-pm/20240715044527.GA1544@sol.localdomain/ Reported-by: Eric Biggers <ebiggers@kernel.org> Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Link: https://bugzilla.kernel.org/show_bug.cgi?id=201761 Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/4950004.31r3eYUQgx@rjwysocki.net
[ rjw: Rebased on top of the current mainline ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change CS35L56_MAIN_RENDER_USER_VOLUME_MAX to 48, to limit the maximum
value of the Speaker Volume control to +12dB. The minimum value is
unchanged so that the default 0dB has the same integer control value.
The original maximum of 400 (+100dB) was the largest value that can be
mathematically handled by the DSP. The actual maximum amplification is
+12dB.
The "Speaker Volume" control was being defined using four hardcoded magic
numbers. There are #defines in the cs35l56.h header for these numbers, so
change the code to use the defined constants.
Dereference auth after NULL check in tpm_buf_check_hmac_response().
Otherwise, unless tpm2_sessions_init() was called, a call can cause NULL
dereference, when TCG_TPM2_HMAC is enabled.
[jarkko: adjusted the commit message.] Cc: stable@vger.kernel.org # v6.10+ Fixes: 7ca110f2679b ("tpm: Address !chip->auth in tpm_buf_append_hmac_session*()") Signed-off-by: Hao Ge <gehao@kylinos.cn> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment, at the end of a DIO write, cifs calls netfs_resize_file() to
adjust the size of the file if it needs it. This will reduce the
zero_point (the point above which we assume a read will just return zeros)
if it's more than the new i_size, but won't increase it.
With DIO writes, however, we definitely want to increase it as we have
clobbered the local pagecache and then written some data that's not
available locally.
Fix cifs to make the zero_point above the end of a DIO or unbuffered write.
This fixes corruption seen occasionally with the generic/708 xfs-test. In
that case, the read-back of some of the written data is being
short-circuited and replaced with zeroes.
Fixes: 3ee1a1fc3981 ("cifs: Cut over to using netfslib") Cc: stable@vger.kernel.org Reported-by: Steve French <sfrench@samba.org> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a subrequest is marked for needing retry, netfs will call
cifs_prepare_write() which will make cifs repick the server for the op
before renegotiating credits; it then calls cifs_issue_write() which
invokes smb2_async_writev() - which re-repicks the server.
If a different server is then selected, this causes the increment of
server->in_flight to happen against one record and the decrement to happen
against another, leading to misaccounting.
Fix this by just removing the repick code in smb2_async_writev(). As this
is only called from netfslib-driven code, cifs_prepare_write() should
always have been called first, and so server should never be NULL and the
preparatory step is repeated in the event that we do a retry.
The problem manifests as a warning looking something like:
Which may be triggered by a number of different xfstests running against an
Azure server in multichannel mode. generic/249 seems the most repeatable,
but generic/215, generic/249 and generic/308 may also show it.
Fixes: 3ee1a1fc3981 ("cifs: Cut over to using netfslib") Cc: stable@vger.kernel.org Reported-by: Steve French <smfrench@gmail.com> Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Acked-by: Tom Talpey <tom@talpey.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Aurelien Aptel <aaptel@suse.com>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are common cases where copy_file_range can noisily
log "source and target of copy not on same server"
e.g. the mv command across mounts to two different server's shares.
Change this to informational rather than logging as an error.
A followon patch will add dynamic trace points e.g. for
cifs_file_copychunk_range
Cc: stable@vger.kernel.org Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A network filesystem needs to implement a netfslib hook to invalidate
fscache if it's to be able to use the cache.
Fix cifs to implement the cache invalidation hook.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org Cc: stable@vger.kernel.org Fixes: 3ee1a1fc3981 ("cifs: Cut over to using netfslib") Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cifs_strict_readv(), the default rc (-EACCES) is accidentally cleared by
a successful return from netfs_start_io_direct(), such that if
cifs_find_lock_conflict() fails, we don't return an error.
Fix this by resetting the default error code.
Fixes: 14b1cd25346b ("cifs: Fix locking in cifs_strict_readv()") Cc: stable@vger.kernel.org Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with the other strings in struct ext4_super_block, s_volume_name is
not NUL terminated. The other strings were marked in commit 072ebb3bffe6
("ext4: add nonstring annotations to ext4.h"). Using strscpy() isn't
the right replacement for strncpy(); it should use memtostr_pad()
instead.
Merge tag 'kbuild-fixes-v6.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Make scripts/ld-version.sh robust against the latest LLD
- Fix warnings in rpm-pkg with device tree support
- Fix warnings in fortify tests with KASAN
* tag 'kbuild-fixes-v6.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
fortify: fix warnings in fortify tests with KASAN
kbuild: rpm-pkg: avoid the warnings with dtb's listed twice
kbuild: Make ld-version.sh more robust against version string changes
When a software KASAN mode is enabled, the fortify tests emit warnings
on some architectures.
For example, for ARCH=arm, the combination of CONFIG_FORTIFY_SOURCE=y
and CONFIG_KASAN=y produces the following warnings:
TEST lib/test_fortify/read_overflow-memchr.log
warning: unsafe memchr() usage lacked '__read_overflow' warning in lib/test_fortify/read_overflow-memchr.c
TEST lib/test_fortify/read_overflow-memchr_inv.log
warning: unsafe memchr_inv() usage lacked '__read_overflow' symbol in lib/test_fortify/read_overflow-memchr_inv.c
TEST lib/test_fortify/read_overflow-memcmp.log
warning: unsafe memcmp() usage lacked '__read_overflow' warning in lib/test_fortify/read_overflow-memcmp.c
TEST lib/test_fortify/read_overflow-memscan.log
warning: unsafe memscan() usage lacked '__read_overflow' symbol in lib/test_fortify/read_overflow-memscan.c
TEST lib/test_fortify/read_overflow2-memcmp.log
warning: unsafe memcmp() usage lacked '__read_overflow2' warning in lib/test_fortify/read_overflow2-memcmp.c
[ more and more similar warnings... ]
Commit 9c2d1328f88a ("kbuild: provide reasonable defaults for tool
coverage") removed KASAN flags from non-kernel objects by default.
It was an intended behavior because lib/test_fortify/*.c are unit
tests that are not linked to the kernel.
As it turns out, some architectures require -fsanitize=kernel-(hw)address
to define __SANITIZE_ADDRESS__ for the fortify tests.
Without __SANITIZE_ADDRESS__ defined, arch/arm/include/asm/string.h
defines __NO_FORTIFY, thus excluding <linux/fortify-string.h>.
This issue does not occur on x86 thanks to commit 4ec4190be4cf
("kasan, x86: don't rename memintrinsics in uninstrumented files"),
but there are still some architectures that define __NO_FORTIFY
in such a situation.
Set KASAN_SANITIZE=y explicitly to the fortify tests.
Fixes: 9c2d1328f88a ("kbuild: provide reasonable defaults for tool coverage") Reported-by: Arnd Bergmann <arnd@arndb.de> Closes: https://lore.kernel.org/all/0e8dee26-41cc-41ae-9493-10cd1a8e3268@app.fastmail.com/ Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
projects / thirdparty / kernel / stable.git / log
