It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 52983382c74f ("mmc: sdhci: enhance preset value function") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device HID AMDI0031 to the AMD GPIO controller driver match table.
This controller can be found on Microsoft Surface Laptop 4 devices and
seems similar enough that we can just copy the existing AMDI0030 entry.
A change in clang 13 results in the __lwsync macro being defined as
__builtin_ppc_lwsync, which emits 'lwsync' or 'msync' depending on what
the target supports. This breaks the build because of -Werror in
arch/powerpc, along with thousands of warnings:
In file included from arch/powerpc/kernel/pmc.c:12:
In file included from include/linux/bug.h:5:
In file included from arch/powerpc/include/asm/bug.h:109:
In file included from include/asm-generic/bug.h:20:
In file included from include/linux/kernel.h:12:
In file included from include/linux/bitops.h:32:
In file included from arch/powerpc/include/asm/bitops.h:62:
arch/powerpc/include/asm/barrier.h:49:9: error: '__lwsync' macro redefined [-Werror,-Wmacro-redefined]
#define __lwsync() __asm__ __volatile__ (stringify_in_c(LWSYNC) : : :"memory")
^
<built-in>:308:9: note: previous definition is here
#define __lwsync __builtin_ppc_lwsync
^
1 error generated.
Undefine this macro so that the runtime patching introduced by
commit 2d1b2027626d ("powerpc: Fixup lwsync at runtime") continues to
work properly with clang and the build no longer breaks.
Davis Mosenkovs [Sat, 10 Jul 2021 18:37:10 +0000 (21:37 +0300)]
mac80211: fix memory corruption in EAPOL handling
Commit e3d4030498c3 ("mac80211: do not accept/forward invalid EAPOL
frames") uses skb_mac_header() before eth_type_trans() is called
leading to incorrect pointer, the pointer gets written to. This issue
has appeared during backporting to 4.4, 4.9 and 4.14.
can_rx_register() callbacks may be called concurrently to the call to
can_rx_unregister(). The callbacks and callback data, though, are
protected by RCU and the struct sock reference count.
So the callback data is really attached to the life of sk, meaning
that it should be released on sk_destruct. However, bcm_remove_op()
calls tasklet_kill(), and RCU callbacks may be called under RCU
softirq, so that cannot be used on kernels before the introduction of
HRTIMER_MODE_SOFT.
However, bcm_rx_handler() is called under RCU protection, so after
calling can_rx_unregister(), we may call synchronize_rcu() in order to
wait for any RCU read-side critical sections to finish. That is,
bcm_rx_handler() won't be called anymore for those ops. So, we only
free them, after we do that synchronize_rcu().
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol") Link: https://lore.kernel.org/r/20210619161813.2098382-1-cascardo@canonical.com Cc: linux-stable <stable@vger.kernel.org> Reported-by: syzbot+0f7e7e5e2f4f40fa89c0@syzkaller.appspotmail.com Reported-by: Norbert Slusarek <nslusarek@gmx.net> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can_can_gw_rcv() is called under RCU protection, so after calling
can_rx_unregister(), we have to call synchronize_rcu in order to wait
for any RCU read-side critical sections to finish before removing the
kmem_cache entry with the referenced gw job entry.
Link: https://lore.kernel.org/r/20210618173645.2238-1-socketcan@hartkopp.net Fixes: c1aabdf379bc ("can-gw: add netlink based CAN routing") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first chunk in a packet is ensured to be present at the beginning of
sctp_rcv(), as a packet needs to have at least 1 chunk. But the second
one, may not be completely available and ch->length can be over
uninitialized memory.
Fix here is by only trying to walk on the next chunk if there is enough to
hold at least the header, and then proceed with the ch->length validation
that is already there.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is btsoc timing issue, after host start to downloading bt firmware,
ep2 need time to switch from function acl to function dfu, so host add
20ms delay as workaround.
Rfkill block and unblock Intel USB Bluetooth [8087:0026] may make it
stops working:
[ 509.691509] Bluetooth: hci0: HCI reset during shutdown failed
[ 514.897584] Bluetooth: hci0: MSFT filter_enable is already on
[ 530.044751] usb 3-10: reset full-speed USB device number 5 using xhci_hcd
[ 545.660350] usb 3-10: device descriptor read/64, error -110
[ 561.283530] usb 3-10: device descriptor read/64, error -110
[ 561.519682] usb 3-10: reset full-speed USB device number 5 using xhci_hcd
[ 566.686650] Bluetooth: hci0: unexpected event for opcode 0x0500
[ 568.752452] Bluetooth: hci0: urb 0000000096cd309b failed to resubmit (113)
[ 578.797955] Bluetooth: hci0: Failed to read MSFT supported features (-110)
[ 586.286565] Bluetooth: hci0: urb 00000000c522f633 failed to resubmit (113)
[ 596.215302] Bluetooth: hci0: Failed to read MSFT supported features (-110)
0x2B, 0x31 and 0x33 are reserved for future use but were not present in
the HCI to MGMT conversion table, this caused the conversion to be
incorrect for the HCI status code greater than 0x2A.
Fix a memory leak when "mda_resolve_route() is called more than once on
the same "rdma_cm_id".
This is possible if cma_query_handler() triggers the
RDMA_CM_EVENT_ROUTE_ERROR flow which puts the state machine back and
allows rdma_resolve_route() to be called again.
net/wireless/wext-spy.c:178:2: warning: 'memcpy' offset [25, 28] from the object at 'threshold' is out of the bounds of referenced subobject 'low' with type 'struct iw_quality' at offset 20 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &threshold.low and &spydata->spy_thr_low. As
these are just a couple of struct members, fix this by using direct
assignments, instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
If SRIOV cannot be disabled during device removal or module unloading,
return error code so it can be logged properly in the calling function.
Note that this can only happen if any VF is currently attached to a
guest using Xen, but not with vfio/KVM. Despite that in that case the
VFs won't work properly with PF removed and/or the module unloaded, I
have let it as is because I don't know what side effects may have
changing it, and also it seems to be the same that other drivers are
doing in this situation.
In the case of being called during SRIOV reconfiguration, the behavior
hasn't changed because the function is called with force=false.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If pci_remove was called for a PF with VFs, the removal of the VFs was
called twice from efx_ef10_sriov_fini: one directly with pci_driver->remove
and another implicit by calling pci_disable_sriov, which also perform
the VFs remove. This was leading to crashing the kernel on the second
attempt.
Given that pci_disable_sriov already calls to pci remove function, get
rid of the direct call to pci_driver->remove from the driver.
2 different ways to trigger the bug:
- Create one or more VFs, then attach the PF to a virtual machine (at
least with qemu/KVM)
- Create one or more VFs, then remove the PF with:
echo 1 > /sys/bus/pci/devices/PF_PCI_ID/remove
Removing sfc module does not trigger the error, at least for me, because
it removes the VF first, and then the PF.
Example of a log with the error:
list_del corruption, ffff967fd20a8ad0->next is LIST_POISON1 (dead000000000100)
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:47!
[...trimmed...]
RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x4c
[...trimmed...]
Call Trace:
efx_dissociate+0x1f/0x140 [sfc]
efx_pci_remove+0x27/0x150 [sfc]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x103/0x1f0
pci_stop_bus_device+0x69/0x90
pci_stop_and_remove_bus_device+0xe/0x20
pci_iov_remove_virtfn+0xba/0x120
sriov_disable+0x2f/0xe0
efx_ef10_pci_sriov_disable+0x52/0x80 [sfc]
? pcie_aer_is_native+0x12/0x40
efx_ef10_sriov_fini+0x72/0x110 [sfc]
efx_pci_remove+0x62/0x150 [sfc]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x103/0x1f0
unbind_store+0xf6/0x130
kernfs_fop_write+0x116/0x190
vfs_write+0xa5/0x1a0
ksys_write+0x4f/0xb0
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
rxe_mr_init_user() always returns the fixed -EINVAL when ib_umem_get()
fails so it's hard for user to know which actual error happens in
ib_umem_get(). For example, ib_umem_get() will return -EOPNOTSUPP when
trying to pin pages on a DAX file.
Because the error handling is sequential, the application of resources
should be carried out in the order of error handling, so the operation
of registering the interrupt handler should be put in front, so as not
to free the unregistered interrupt handler during error handling.
When 'nicstar_init_one' fails, 'ns_init_card_error' will be executed for
error handling, but the correct memory free function should be used,
otherwise it will cause an error. Since 'card->rsq.org' and
'card->tsq.org' are allocated using 'dma_alloc_coherent' function, they
should be freed using 'dma_free_coherent'.
Fix this by using 'dma_free_coherent' instead of 'kfree'
MIPS is the ONLY arch just defining __HAVE_ARCH_PMD_ALLOC_ONE alone.
Since commit b2b29d6d011944 (mm: account PMD tables like PTE tables),
"pmd_free" in asm-generic with PMD table accounting and "pmd_alloc_one"
in MIPS without PMD table accounting causes PageTable accounting number
negative, which read by global_zone_page_state(), always returns 0.
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
At least on wl12xx, reading the MAC after boot can fail with a warning
at drivers/net/wireless/ti/wlcore/sdio.c:78 wl12xx_sdio_raw_read.
The failed call comes from wl12xx_get_mac() that wlcore_nvs_cb() calls
after request_firmware_work_func().
After the error, no wireless interface is created. Reloading the wl12xx
module makes the interface work.
Turns out the wlan controller can be in a low-power ELP state after the
boot from the bootloader or kexec, and needs to be woken up first.
Let's wake the hardware and add a sleep after that similar to
wl12xx_pre_boot() is already doing.
Note that a similar issue could exist for wl18xx, but I have not seen it
so far. And a search for wl18xx_get_mac and wl12xx_sdio_raw_read did not
produce similar errors.
When memory allocation for XFRMA_ENCAP or XFRMA_COADDR fails,
the error will not be reported because the -ENOMEM assignment
to the err variable is overwritten before. Fix this by moving
these two in front of the function so that memory allocation
failures will be reported.
In the field, we have seen lots of allocation failure from the call
path below.
06-03 13:29:12.999 1010315 31557 31557 W Binder : 31542_2: page allocation failure: order:0, mode:0x800(GFP_NOWAIT), nodemask=(null),cpuset=background,mems_allowed=0
...
...
06-03 13:29:12.999 1010315 31557 31557 W Call trace:
06-03 13:29:12.999 1010315 31557 31557 W : dump_backtrace.cfi_jt+0x0/0x8
06-03 13:29:12.999 1010315 31557 31557 W : dump_stack+0xc8/0x14c
06-03 13:29:12.999 1010315 31557 31557 W : warn_alloc+0x158/0x1c8
06-03 13:29:12.999 1010315 31557 31557 W : __alloc_pages_slowpath+0x9d8/0xb80
06-03 13:29:12.999 1010315 31557 31557 W : __alloc_pages_nodemask+0x1c4/0x430
06-03 13:29:12.999 1010315 31557 31557 W : allocate_slab+0xb4/0x390
06-03 13:29:12.999 1010315 31557 31557 W : ___slab_alloc+0x12c/0x3a4
06-03 13:29:12.999 1010315 31557 31557 W : kmem_cache_alloc+0x358/0x5e4
06-03 13:29:12.999 1010315 31557 31557 W : avc_alloc_node+0x30/0x184
06-03 13:29:12.999 1010315 31557 31557 W : avc_update_node+0x54/0x4f0
06-03 13:29:12.999 1010315 31557 31557 W : avc_has_extended_perms+0x1a4/0x460
06-03 13:29:12.999 1010315 31557 31557 W : selinux_file_ioctl+0x320/0x3d0
06-03 13:29:12.999 1010315 31557 31557 W : __arm64_sys_ioctl+0xec/0x1fc
06-03 13:29:12.999 1010315 31557 31557 W : el0_svc_common+0xc0/0x24c
06-03 13:29:12.999 1010315 31557 31557 W : el0_svc+0x28/0x88
06-03 13:29:12.999 1010315 31557 31557 W : el0_sync_handler+0x8c/0xf0
06-03 13:29:12.999 1010315 31557 31557 W : el0_sync+0x1a4/0x1c0
..
..
06-03 13:29:12.999 1010315 31557 31557 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:12.999 1010315 31557 31557 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:12.999 1010315 31557 31557 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:12.999 1010161 10686 10686 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:12.999 1010161 10686 10686 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:12.999 1010161 10686 10686 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:12.999 1010161 10686 10686 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:12.999 1010161 10686 10686 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:12.999 1010161 10686 10686 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:12.999 1010161 10686 10686 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:12.999 1010161 10686 10686 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:12.999 1010161 10686 10686 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:13.000 1010161 10686 10686 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:13.000 1010161 10686 10686 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:13.000 1010161 10686 10686 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:13.000 1010161 10686 10686 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:13.000 1010161 10686 10686 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:13.000 1010161 10686 10686 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:13.000 1010161 10686 10686 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:13.000 1010161 10686 10686 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:13.000 1010161 10686 10686 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:13.000 10230 30892 30892 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:13.000 10230 30892 30892 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
06-03 13:29:13.000 10230 30892 30892 W node 0 : slabs: 57, objs: 2907, free: 0
06-03 13:29:13.000 10230 30892 30892 W SLUB : Unable to allocate memory on node -1, gfp=0x900(GFP_NOWAIT|__GFP_ZERO)
06-03 13:29:13.000 10230 30892 30892 W cache : avc_node, object size: 72, buffer size: 80, default order: 0, min order: 0
Based on [1], selinux is tolerate for failure of memory allocation.
Then, use __GFP_NOWARN together.
[1] 476accbe2f6e ("selinux: use GFP_NOWAIT in the AVC kmem_caches")
Signed-off-by: Minchan Kim <minchan@kernel.org>
[PM: subj fix, line wraps, normalized commit refs] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current commit code resets the place where the search for free blocks
will begin back to the start of the metadata device. There are a couple
of repercussions to this:
- The first allocation after the commit is likely to take longer than
normal as it searches for a free block in an area that is likely to
have very few free blocks (if any).
- Any free blocks it finds will have been recently freed. Reusing them
means we have fewer old copies of the metadata to aid recovery from
hardware error.
Fix these issues by leaving the cursor alone, only resetting when the
search hits the end of the metadata device.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a complement to commit aa6dd211e4b1 ("inet: use bigger hash
table for IP ID generation"), but focusing on some specific aspects
of IPv6.
Contary to IPv4, IPv6 only uses packet IDs with fragments, and with a
minimum MTU of 1280, it's much less easy to force a remote peer to
produce many fragments to explore its ID sequence. In addition packet
IDs are 32-bit in IPv6, which further complicates their analysis. On
the other hand, it is often easier to choose among plenty of possible
source addresses and partially work around the bigger hash table the
commit above permits, which leaves IPv6 partially exposed to some
possibilities of remote analysis at the risk of weakening some
protocols like DNS if some IDs can be predicted with a good enough
probability.
Given the wide range of permitted IDs, the risk of collision is extremely
low so there's no need to rely on the positive increment algorithm that
is shared with the IPv4 code via ip_idents_reserve(). We have a fast
PRNG, so let's simply call prandom_u32() and be done with it.
Performance measurements at 10 Gbps couldn't show any difference with
the previous code, even when using a single core, because due to the
large fragments, we're limited to only ~930 kpps at 10 Gbps and the cost
of the random generation is completely offset by other operations and by
the network transfer time. In addition, this change removes the need to
update a shared entry in the idents table so it may even end up being
slightly faster on large scale systems where this matters.
The risk of at least one collision here is about 1/80 million among
10 IDs, 1/850k among 100 IDs, and still only 1/8.5k among 1000 IDs,
which remains very low compared to IPv4 where all IDs are reused
every 4 to 80ms on a 10 Gbps flow depending on packet sizes.
Reported-by: Amit Klein <aksecurity@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20210529110746.6796-1-w@1wt.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PLLU (USB) consists of the PLL configuration itself and configuration
of the PLLU outputs. The PLLU programming is inconsistent on T30 vs T114,
where T114 immediately bails out if PLLU is enabled and T30 re-enables
a potentially already enabled PLL (left after bootloader) and then fully
reprograms it, which could be unsafe to do. The correct way should be to
skip enabling of the PLL if it's already enabled and then apply
configuration to the outputs. This patch doesn't fix any known problems,
it's a minor improvement.
In function udf_symlink, epos.bh is assigned with the value returned
by udf_tgetblk. The function udf_tgetblk is defined in udf/misc.c
and returns the value of sb_getblk function that could be NULL.
Then, epos.bh is used without any check, causing a possible
NULL pointer dereference when sb_getblk fails.
This fix adds a check to validate the value of epos.bh.
The virtio_gpu_init() will free vgdev and vgdev->vbufs on failure.
But such failure will be caught by virtio_gpu_probe() and then
virtio_gpu_release() will be called to do some cleanup which
will free vgdev and vgdev->vbufs again. So let's set dev->dev_private
to NULL to avoid double free.
__napi_schedule_irqoff() is an optimized version of __napi_schedule()
which can be used where it is known that interrupts are disabled,
e.g. in interrupt-handlers, spin_lock_irq() sections or hrtimer
callbacks.
On PREEMPT_RT enabled kernels this assumptions is not true. Force-
threaded interrupt handlers and spinlocks are not disabling interrupts
and the NAPI hrtimer callback is forced into softirq context which runs
with interrupts enabled as well.
Chasing all usage sites of __napi_schedule_irqoff() is a whack-a-mole
game so make __napi_schedule_irqoff() invoke __napi_schedule() for
PREEMPT_RT kernels.
The callers of ____napi_schedule() in the networking core have been
audited and are correct on PREEMPT_RT kernels as well.
Reported-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zou Wei <zou_wei@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zou Wei <zou_wei@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zou Wei <zou_wei@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If multiple threads are accessing the same huge page at the same
time, hugetlb_cow will be called if one thread write the COW huge
page. And function huge_ptep_clear_flush is called to notify other
threads to clear the huge pte tlb entry. The other threads clear
the huge pte tlb entry and reload it from page table, the reload
huge pte entry may be old.
This patch fixes this issue on mips platform, and it clears huge
pte entry before notifying other threads to flush current huge
page entry, it is similar with other architectures.
Signed-off-by: Bibo Mao <maobibo@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sparse is not happy about handling of strict types in pch_ptp_match():
.../pch_gbe_main.c:158:33: warning: incorrect type in argument 2 (different base types)
.../pch_gbe_main.c:158:33: expected unsigned short [usertype] uid_hi
.../pch_gbe_main.c:158:33: got restricted __be16 [usertype]
.../pch_gbe_main.c:158:45: warning: incorrect type in argument 3 (different base types)
.../pch_gbe_main.c:158:45: expected unsigned int [usertype] uid_lo
.../pch_gbe_main.c:158:45: got restricted __be32 [usertype]
.../pch_gbe_main.c:158:56: warning: incorrect type in argument 4 (different base types)
.../pch_gbe_main.c:158:56: expected unsigned short [usertype] seqid
.../pch_gbe_main.c:158:56: got restricted __be16 [usertype]
Fix that by switching to use proper accessors to BE data.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Flavio Suligoi <f.suligoi@asem.it> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the device is power-cycled, it takes time for the initiator to transmit
the periodic NOTIFY (ENABLE SPINUP) SAS primitive, and for the device to
respond to the primitive to become ACTIVE. Retry the I/O request to allow
the device time to become ACTIVE.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210629155826.48441-1-quat.le@oracle.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Quat Le <quat.le@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().
Patch series "selftests/vm/pkeys: Bug fixes and a new test".
There has been a lot of activity on the x86 front around the XSAVE
architecture which is used to context-switch processor state (among other
things). In addition, AMD has recently joined the protection keys club by
adding processor support for PKU.
The AMD implementation helped uncover a kernel bug around the PKRU "init
state", which actually applied to Intel's implementation but was just
harder to hit. This series adds a test which is expected to help find
this class of bug both on AMD and Intel. All the work around pkeys on x86
also uncovered a few bugs in the selftest.
This patch (of 4):
The "random" pkey allocation code currently does the good old:
srand((unsigned int)time(NULL));
*But*, it unfortunately does this on every random pkey allocation.
There may be thousands of these a second. time() has a one second
resolution. So, each time alloc_random_pkey() is called, the PRNG is
*RESET* to time(). This is nasty. Normally, if you do:
srand(<ANYTHING>);
foo = rand();
bar = rand();
You'll be quite guaranteed that 'foo' and 'bar' are different. But, if
you do:
srand(1);
foo = rand();
srand(1);
bar = rand();
You are quite guaranteed that 'foo' and 'bar' are the *SAME*. The recent
"fix" effectively forced the test case to use the same "random" pkey for
the whole test, unless the test run crossed a second boundary.
Only run srand() once at program startup.
This explains some very odd and persistent test failures I've been seeing.
Link: https://lkml.kernel.org/r/20210611164153.91B76FB8@viggo.jf.intel.com Link: https://lkml.kernel.org/r/20210611164155.192D00FF@viggo.jf.intel.com Fixes: 6e373263ce07 ("selftests/vm/pkeys: fix alloc_random_pkey() to make it really random") Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Sandipan Das <sandipan@linux.ibm.com> Cc: Florian Weimer <fweimer@redhat.com> Cc: "Desnes A. Nunes do Rosario" <desnesn@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thiago Jung Bauermann <bauerman@linux.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Hocko <mhocko@kernel.org> Cc: Michal Suchanek <msuchanek@suse.de> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If other processes are mapping any other subpages of the hugepage, i.e.
in pte-mapped thp case, page_mapcount() will return 1 incorrectly. Then
we would discard the page while other processes are still mapping it. Fix
it by using total_mapcount() which can tell whether other processes are
still mapping it.
Link: https://lkml.kernel.org/r/20210511134857.1581273-6-linmiaohe@huawei.com Fixes: b8d3c4c3009d ("mm/huge_memory.c: don't split THP page when MADV_FREE syscall is called") Reviewed-by: Yang Shi <shy828301@gmail.com> Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Rik van Riel <riel@surriel.com> Cc: Song Liu <songliubraving@fb.com> Cc: William Kucharski <william.kucharski@oracle.com> Cc: Zi Yan <ziy@nvidia.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The platform device driver name is "max8997-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
When sm5502_init_dev_type() iterates over sm5502_reg_data to
initialize the registers it is limited by ARRAY_SIZE(sm5502_reg_data).
There is no need to add another empty element to sm5502_reg_data.
Having the additional empty element in sm5502_reg_data will just
result in writing 0xff to register 0x00, which does not really
make sense.
Fixes: 914b881f9452 ("extcon: sm5502: Add support new SM5502 extcon device driver") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an expander does not contain any 'phys', an appropriate error code -1
should be returned, as done elsewhere in this function. However, we
currently do not explicitly assign this error code to 'rc'. As a result, 0
was incorrectly returned.
Link: https://lore.kernel.org/r/20210514081300.6650-1-thunder.leizhen@huawei.com Fixes: f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Variable "size" has type "phys_addr_t", which can be either 32-bit or
64-bit on 32-bit systems, while "unsigned long" is always 32-bit on
32-bit systems. Hence the cast in
(unsigned long)size / SZ_1M
may truncate a 64-bit size to 32-bit, as casts have a higher operator
precedence than divisions.
Fix this by inverting the order of the cast and division, which should
be safe for memory blocks smaller than 4 PiB. Note that the division is
actually a shift, as SZ_1M is a power-of-two constant, hence there is no
need to use div_u64().
While at it, use "%lu" to format "unsigned long".
Fixes: e8d9d1f5485b52ec ("drivers: of: add initialization code for static reserved memory") Fixes: 3f0c8206644836e4 ("drivers: of: add initialization code for dynamic reserved memory") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/4a1117e72d13d26126f57be034c20dac02f1e915.1623835273.git.geert+renesas@glider.be Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There needs to be a check to verify that we don't read beyond the end
of "buf". This function is called from do_rx(). The "buf" is the USB
transfer_buffer and "len" is "urb->actual_length".
APPLDATA_BASE should depend on PROC_SYSCTL instead of PROC_FS.
Building with PROC_FS but not PROC_SYSCTL causes a build error,
since appldata_base.c uses data and APIs from fs/proc/proc_sysctl.c.
arch/s390/appldata/appldata_base.o: in function `appldata_generic_handler':
appldata_base.c:(.text+0x192): undefined reference to `sysctl_vals'
The BusLogic driver has build errors on ia64 due to a name collision (in
the #included FlashPoint.c file). Rename the struct field in struct
sccb_mgr_info from si_flags to si_mflags (manager flags) to mend the build.
This is the first problem. There are 50+ others after this one:
In file included from ../include/uapi/linux/signal.h:6,
from ../include/linux/signal_types.h:10,
from ../include/linux/sched.h:29,
from ../include/linux/hardirq.h:9,
from ../include/linux/interrupt.h:11,
from ../drivers/scsi/BusLogic.c:27:
../arch/ia64/include/uapi/asm/siginfo.h:15:27: error: expected ':', ',', ';', '}' or '__attribute__' before '.' token
15 | #define si_flags _sifields._sigfault._flags
| ^
../drivers/scsi/FlashPoint.c:43:6: note: in expansion of macro 'si_flags'
43 | u16 si_flags;
| ^~~~~~~~
In file included from ../drivers/scsi/BusLogic.c:51:
../drivers/scsi/FlashPoint.c: In function 'FlashPoint_ProbeHostAdapter':
../drivers/scsi/FlashPoint.c:1076:11: error: 'struct sccb_mgr_info' has no member named '_sifields'
1076 | pCardInfo->si_flags = 0x0000;
| ^~
../drivers/scsi/FlashPoint.c:1079:12: error: 'struct sccb_mgr_info' has no member named '_sifields'
Link: https://lore.kernel.org/r/20210529234857.6870-1-rdunlap@infradead.org Fixes: 391e2f25601e ("[SCSI] BusLogic: Port driver to 64-bit.") Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Hannes Reinecke <hare@suse.de> Cc: Khalid Aziz <khalid.aziz@oracle.com> Cc: Khalid Aziz <khalid@gonehiking.org> Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Theoretically, it will cause index out of bounds error if
'num_bytes_read' is greater than 4. As we expect it(and was tested)
never to be greater than 4, error out if it happens.
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of uses of
iio_push_to_buffers_with_timestamp()
Fixes: a244e7b57f0f ("iio: Add driver for AMS/TAOS tcs3414 digital color sensor") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210501170121.512209-19-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported warning in tcindex_alloc_perfect_hash. The problem
was in too big cp->hash, which triggers warning in kmalloc. Since
cp->hash comes from userspace, there is no need to warn if value
is not correct
Fixes: b9a24bb76bf6 ("net_sched: properly handle failure case of tcf_exts_init()") Reported-and-tested-by: syzbot+1071ad60cd7df39fdadb@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Acked-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The caller of wb_get_create() should pin the memcg, because
wb_get_create() relies on this guarantee. The rcu read lock
only can guarantee that the memcg css returned by css_from_id()
cannot be released, but the reference of the memcg can be zero.
rcu_read_lock()
memcg_css = css_from_id()
wb_get_create(memcg_css)
cgwb_create(memcg_css)
// css_get can change the ref counter from 0 back to 1
css_get(memcg_css)
rcu_read_unlock()
Fix it by holding a reference to the css before calling
wb_get_create(). This is not a problem I encountered in the
real world. Just the result of a code review.
Fixes: 682aa8e1a6a1 ("writeback: implement unlocked_inode_to_wb transaction and use it for stat updates") Link: https://lore.kernel.org/r/20210402091145.80635-1-songmuchun@bytedance.com Signed-off-by: Muchun Song <songmuchun@bytedance.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add Advertising - Success (ScRsp only) - run
Sending Add Advertising (0x003e)
Test condition added, total 1
[ 11.004577] ==================================================================
[ 11.005292] BUG: KASAN: slab-out-of-bounds in tlv_data_is_valid+0x87/0xe0
[ 11.005984] Read of size 1 at addr ffff888002c695b0 by task mgmt-tester/87
[ 11.006711]
[ 11.007176]
[ 11.007429] Allocated by task 87:
[ 11.008151]
[ 11.008438] The buggy address belongs to the object at ffff888002c69580
[ 11.008438] which belongs to the cache kmalloc-64 of size 64
[ 11.010526] The buggy address is located 48 bytes inside of
[ 11.010526] 64-byte region [ffff888002c69580, ffff888002c695c0)
[ 11.012423] The buggy address belongs to the page:
[ 11.013291]
[ 11.013544] Memory state around the buggy address:
[ 11.014359] ffff888002c69480: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.015453] ffff888002c69500: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.016232] >ffff888002c69580: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc
[ 11.017010] ^
[ 11.017547] ffff888002c69600: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc
[ 11.018296] ffff888002c69680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.019116] ==================================================================
When vsi->type == I40E_VSI_FDIR, we have caught the return value of
i40e_vsi_request_irq() but without further handling. Check and execute
memory clean on failure just like the other i40e_vsi_request_irq().
Fixes: 8a9eb7d3cbcab ("i40e: rework fdir setup and teardown") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As documented at drivers/base/platform.c for platform_get_irq:
* Gets an IRQ for a platform device and prints an error message if finding the
* IRQ fails. Device drivers should check the return value for errors so as to
* not pass a negative integer value to the request_irq() APIs.
So, the driver should check that platform_get_irq() return value
is _negative_, not that it's equal to zero, because -ENXIO (return
value from request_irq() if irq was not found) will
pass this check and it leads to passing negative irq to request_irq()
Fixes: 0dd077093636 ("NET: Add ezchip ethernet driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after netif_napi_del()
call.
Fixes: 0dd077093636 ("NET: Add ezchip ethernet driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
greth is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing greth
pointer. So, fix it by moving free_netdev() after of_iounmap()
call.
Fixes: d4c41139df6e ("net: Add Aeroflex Gaisler 10/100/1G Ethernet MAC driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ipv6_find_hdr() does not validate that this is an IPv6 packet. Add a
sanity check for calling ipv6_find_hdr() to make sure an IPv6 packet
is passed for parsing.
Fixes: 63c416887437 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the code execute this if statement, the value of ret is 0.
However, we can see from the ath10k_warn() log that the value of
ret should be -EINVAL.
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: ccec9038c721 ("ath10k: enable raw encap mode and software crypto engine") Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1621939577-62218-1-git-send-email-yang.lee@linux.alibaba.com Signed-off-by: Sasha Levin <sashal@kernel.org>
kernel test robot reports over 200 build errors and warnings
that are due to this Kconfig problem when CARL9170=m,
MAC80211=y, and LEDS_CLASS=m.
WARNING: unmet direct dependencies detected for MAC80211_LEDS
Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y])
Selected by [m]:
- CARL9170_LEDS [=y] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && CARL9170 [=m]
CARL9170_LEDS selects MAC80211_LEDS even though its kconfig
dependencies are not met. This happens because 'select' does not follow
any Kconfig dependency chains.
Fix this by making CARL9170_LEDS depend on MAC80211_LEDS, where
the latter supplies any needed dependencies on LEDS_CLASS.
Fixes: 1d7e1e6b1b8ed ("carl9170: Makefile, Kconfig files and MAINTAINERS") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: linux-wireless@vger.kernel.org Cc: Arnd Bergmann <arnd@arndb.de> Suggested-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210530031134.23274-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The object surf is not fully initialized and the uninitialized
field surf.data is being copied by the call to qxl_bo_create
via the call to qxl_gem_object_create. Set surf.data to zero
to ensure garbage data from the stack is not being copied.
To avoid the following failure when trying to load the rdma_rxe module
while IPv6 is disabled, add a check for EAFNOSUPPORT and ignore the
failure, also delete the needless debug print from rxe_setup_udp_tunnel().
$ modprobe rdma_rxe
modprobe: ERROR: could not insert 'rdma_rxe': Operation not permitted
Fixes: dfdd6158ca2c ("IB/rxe: Fix kernel panic in udp_setup_tunnel") Link: https://lore.kernel.org/r/20210603090112.36341-1-kamalheib1@gmail.com Reported-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Kamal Heib <kamalheib1@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The snprintf() function returns the number of bytes which would have been
printed if the buffer was large enough. In other words it can return ">=
remain" but this code assumes it returns "== remain".
The run time impact of this bug is not very severe. The next iteration
through the loop would trigger a WARN() when we pass a negative limit to
snprintf(). We would then return success instead of -E2BIG.
The kernel implementation of snprintf() will never return negatives so
there is no need to check and I have deleted that dead code.
Link: https://lkml.kernel.org/r/20210511135350.GV1955@kadam Fixes: a860f6eb4c6a ("ocfs2: sysfile interfaces for online file check") Fixes: 74ae4e104dfc ("ocfs2: Create stack glue sysfs files.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, a device description can be obtained using ACPI, if the _STR
method exists for a particular device, and then exposed to the userspace
via a sysfs object as a string value.
If the _STR method is available for a given device then the data
(usually a Unicode string) is read and stored in a buffer (of the
ACPI_TYPE_BUFFER type) with a pointer to said buffer cached in the
struct acpi_device_pnp for later access.
The description_show() function is responsible for exposing the device
description to the userspace via a corresponding sysfs object and
internally calls the utf16s_to_utf8s() function with a pointer to the
buffer that contains the Unicode string so that it can be converted from
UTF16 encoding to UTF8 and thus allowing for the value to be safely
stored and later displayed.
When invoking the utf16s_to_utf8s() function, the description_show()
function also sets a limit of the data that can be saved into a provided
buffer as a result of the character conversion to be a total of
PAGE_SIZE, and upon completion, the utf16s_to_utf8s() function returns
an integer value denoting the number of bytes that have been written
into the provided buffer.
Following the execution of the utf16s_to_utf8s() a newline character
will be added at the end of the resulting buffer so that when the value
is read in the userspace through the sysfs object then it would include
newline making it more accessible when working with the sysfs file
system in the shell, etc. Normally, this wouldn't be a problem, but if
the function utf16s_to_utf8s() happens to return the number of bytes
written to be precisely PAGE_SIZE, then we would overrun the buffer and
write the newline character outside the allotted space which can have
undefined consequences or result in a failure.
To fix this buffer overrun, ensure that there always is enough space
left for the newline character to be safely appended.
Fixes: d1efe3c324ea ("ACPI: Add new sysfs interface to export device description") Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function nx842_OF_upd_status triggers a sparse RCU warning when
it directly dereferences the RCU-protected devdata. This appears
to be an accident as there was another variable of the same name
that was passed in from the caller.
After it was removed (because the main purpose of using it, to
update the status member was itself removed) the global variable
unintenionally stood in as its replacement.
The current sun6i SPI implementation initializes the transfer too early,
resulting in SCK going high before the transfer. When using an additional
(gpio) chipselect with sun6i, the chipselect is asserted at a time when
clock is high, making the SPI transfer fail.
This is due to SUN6I_GBL_CTL_BUS_ENABLE being written into
SUN6I_GBL_CTL_REG at an early stage. Moving that to the transfer
function, hence, right before the transfer starts, mitigates that
problem.
Fans 7..12 do not have their own set of configuration registers.
So far the code ignored that and read beyond the end of the configuration
register range to get the tachometer period. This resulted in more or less
random fan speed values for those fans.
The datasheet is quite vague when it comes to defining the tachometer
period for fans 7..12. Experiments confirm that the period is the same
for both fans associated with a given set of configuration registers.
Fixes: 54187ff9d766 ("hwmon: (max31790) Convert to use new hwmon registration API") Fixes: 195a4b4298a7 ("hwmon: Driver for Maxim MAX31790") Cc: Jan Kundrát <jan.kundrat@cesnet.cz> Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Václav Kubernát <kubernat@cesnet.cz> Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20210526154022.3223012-2-linux@roeck-us.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Valid Maxim Integrated ACPI device IDs would start with MXIM,
not with MAX1. On top of that, ACPI device IDs reflecting chip names
are almost always invalid.
Remove the invalid ACPI IDs.
Fixes: 04e1e70afec6 ("hwmon: (max31722) Add support for MAX31722/MAX31723 temperature sensors") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rename struct sms_msg_data4 to sms_msg_data5 and increase the size of
its msg_data array from 4 to 5 elements. Notice that at some point
the 5th element of msg_data is being accessed in function
smscore_load_firmware_family2():
1006 trigger_msg->msg_data[4] = 4; /* Task ID */
Also, there is no need for the object _trigger_msg_ of type struct
sms_msg_data *, when _msg_ can be used, directly. Notice that msg_data
in struct sms_msg_data is a one-element array, which causes multiple
out-of-bounds warnings when accessing beyond its first element
in function smscore_load_firmware_family2():
the out-of-bounds warnings are actually valid and should be addressed.
Fix this by declaring object _msg_ of type struct sms_msg_data5 *,
which contains a 5-elements array, instead of just 4. And use
_msg_ directly, instead of creating object trigger_msg.
This helps with the ongoing efforts to enable -Warray-bounds by fixing
the following warnings:
CC [M] drivers/media/common/siano/smscoreapi.o
drivers/media/common/siano/smscoreapi.c: In function ‘smscore_load_firmware_family2’:
drivers/media/common/siano/smscoreapi.c:1003:24: warning: array subscript 1 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1003 | trigger_msg->msg_data[1] = 6; /* Priority */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1004:24: warning: array subscript 2 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1004 | trigger_msg->msg_data[2] = 0x200; /* Stack size */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1005:24: warning: array subscript 3 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1005 | trigger_msg->msg_data[3] = 0; /* Parameter */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1006:24: warning: array subscript 4 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1006 | trigger_msg->msg_data[4] = 4; /* Task ID */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
Fixes: 018b0c6f8acb ("[media] siano: make load firmware logic to work with newer firmwares") Co-developed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the CSI bps per lane is not in the valid range, an appropriate error
code -EINVAL should be returned. However, we currently do not explicitly
assign this error code to 'ret'. As a result, 0 was incorrectly returned.
Fixes: 256148246852 ("[media] tc358743: support probe from device tree") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
