Function max310x_tx_empty() accesses the IRQSTS register, which is
cleared by IC when reading, so if there is an interrupt status, we
will lose it. This patch implement the transmitter check only by
the current FIFO level.
The Broadcom controller on aries S5PV210 boards sends out a couple of
unknown packets after the firmware is loaded. This will cause
logging of errors such as:
Bluetooth: hci0: Frame reassembly failed (-84)
This is probably also the case with other boards, as there are related
Android userspace patches for custom ROMs such as
https://review.lineageos.org/#/c/LineageOS/android_system_bt/+/142721/
Since this appears to be intended behaviour, treated them as diagnostic
packets.
Note that this is another variant of commit 01d5e44ace8a
("Bluetooth: hci_bcm: Handle empty packet after firmware loading")
If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().
However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.
Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.
Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
TIMER_INTR_MASK register (Base Address of Timer + 0x38) is not designed
for masking interrupts on ast2500 chips, and it's not even listed in
ast2400 datasheet, so it's not safe to access TIMER_INTR_MASK on aspeed
chips.
Similarly, TIMER_INTR_STATE register (Base Address of Timer + 0x34) is
not interrupt status register on ast2400 and ast2500 chips. Although
there is no side effect to reset the register in fttmr010_common_init(),
it's just misleading to do so.
Besides, "count_down" is renamed to "is_aspeed" in "fttmr010" structure,
and more comments are added so the code is more readble.
Signed-off-by: Tao Ren <taoren@fb.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bulkstat family of ioctls are problematic on x32, because there is
a mixup of native 32-bit and 64-bit conventions. The xfs_fsop_bulkreq
struct contains pointers and 32-bit integers so that matches the native
32-bit layout, and that means the ioctl implementation goes into the
regular compat path on x32.
However, the 'ubuffer' member of that struct in turn refers to either
struct xfs_inogrp or xfs_bstat (or an array of these). On x32, those
structures match the native 64-bit layout. The compat implementation
writes out the 32-bit version of these structures. This is not the
expected format for x32 userspace, causing problems.
Fortunately the functions which actually output these xfs_inogrp and
xfs_bstat structures have an easy way to select which output format
is required, so we just need a little tweak to select the right format
on x32.
Signed-off-by: Nick Bowler <nbowler@draconx.ca> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While inspecting the ioctl implementations, I noticed that the compat
implementation of XFS_IOC_ATTRLIST_BY_HANDLE does not do exactly the
same thing as the native implementation. Specifically, the "cursor"
does not appear to be written out to userspace on the compat path,
like it is on the native path.
This adjusts the compat implementation to copy out the cursor just
like the native implementation does. The attrlist cursor does not
require any special compat handling. This fixes xfstests xfs/269
on both IA-32 and x32 userspace, when running on an amd64 kernel.
Signed-off-by: Nick Bowler <nbowler@draconx.ca> Fixes: 0facef7fb053b ("xfs: in _attrlist_by_handle, copy the cursor back to userspace") Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sending a check/repair message infrequently leads to -EBUSY instead of
properly identifying an active resync. This occurs because
raid_message() is testing recovery bits in a racy way.
Fix by calling decipher_sync_action() from raid_message() to properly
identify the idle state of the RAID device.
Before this patch, function do_grow would not reserve enough journal
blocks in the transaction to unstuff jdata files while growing them.
This patch adds the logic to add one more block if the file to grow
is jdata.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The flakey target is documented to be able to corrupt the Nth byte in
a bio, but does not corrupt byte indices after the first biovec in the
bio. Change the corrupting function to actually corrupt the Nth byte
no matter in which biovec that index falls.
A test device generating two-page bios, atop a flakey device configured
to corrupt a byte index on the second page, verified both the failure
to corrupt before this patch and the expected corruption after this
change.
Signed-off-by: John Dorminy <jdorminy@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.
Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].
The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.
The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.
With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the current driver, the statistics reported by .ndo_get_stats64()
are reset when the device goes down. Store a snapshot of the
rtnl_link_stats64 before shutdown. This snapshot is added to the
current counters in .ndo_get_stats64() so that the counters will not
get reset when the device is down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each media stream negotiation between 2 SIP peers will trigger creation
of 4 different expectations (2 RTP and 2 RTCP):
- INVITE will create expectations for the media packets sent by the
called peer
- reply to the INVITE will create expectations for media packets sent
by the caller
The dport used by these expectations usually match the ones selected
by the SIP peers, but they might get translated due to conflicts with
another expectation. When such event occur, it is important to do
this translation in both directions, dport translation on the receiving
path and sport translation on the sending path.
This commit fixes the sport translation when the peer requiring it is
also the one that starts the media stream. In this scenario, first media
stream packet is forwarded from LAN to WAN and will rely on
nf_nat_sip_expected() to do the necessary sport translation. However, the
expectation matched by this packet does not contain the necessary information
for doing SNAT, this data being stored in the paired expectation created by
the sender's SIP message (INVITE or reply to it).
The failure to create debugfs entry is unpleasant event, but not enough
to abort drier initialization. Align the mlx5_core code to debugfs design
and continue execution whenever debugfs_create_dir() successes or not.
Commit 21abf103818a
("gpio: Pass a flag to gpiochip_request_own_desc()")
started to pass an enum gpiod_flags but this file is
not including the header file that defines that enum
and the compiler spits:
drivers/memory/omap-gpmc.c: In function
'gpmc_probe_generic_child':
drivers/memory/omap-gpmc.c:2174:9: error: type of formal
parameter 4 is incomplete
0);
^
Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: 21abf103818a ("gpio: Pass a flag to gpiochip_request_own_desc()") Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
samples/vfio-mdev/mtty.c:592:39: warning: implicit conversion from 'int'
to 'char' changes value from 162 to -94 [-Wconstant-conversion]
*buf = UART_MSR_DSR | UART_MSR_DDSR | UART_MSR_DCD;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
1 warning generated.
Turns out that all uses of buf in this function ultimately end up stored
or cast to an unsigned type. Just use u8, which has the same number of
bits but can store this larger number so Clang no longer warns.
Blacklist symbols in arch-defined probe-prohibited areas.
With this change, user can see all symbols which are prohibited
to probe in debugfs.
All archtectures which have custom prohibit areas should define
its own arch_populate_kprobe_blacklist() function, but unless that,
all symbols marked __kprobes are blacklisted.
Reported-by: Andrea Righi <righi.andrea@gmail.com> Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: David S. Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yonghong Song <yhs@fb.com> Link: http://lkml.kernel.org/r/154503485491.26176.15823229545155174796.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If pcistub_init_device fails, the release function will be called with
dev_data set to NULL. Check it before using it to avoid a NULL pointer
dereference.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the characters to the workqueue
for the tty layer to handle them. When this busy time on the serial/tty
subsystem happens during boot, where it is also busy on the userspace
trying to initialise, some processes can continuously get preempted
and will be on hold until the interrupts subside.
The fix is to backoff on processing received characters for a specified
amount of time when an input overrun is seen (received a new character
before the previous one is processed). This only stops receive and will
continue to transmit characters to serial port. After the backoff period
is done, it receive will be re-enabled. This is optional and will only
be enabled by setting 'overrun-throttle-ms' in the dts.
We're getting a reference RPi's firmware node in order to be able to
communicate with it's driver. We should decrease the reference count on
the dt node after being done with it.
Fixes: a98d90e7d588 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When falling back to PIO, active_rx must be set to a different value
than cookie_rx[i], else sci_dma_rx_find_active() will incorrectly find a
match, leading to a NULL pointer dereference in rx_timer_fn() later.
Use zero instead, which is the same value as after driver
initialization.
We use this number to figure out how many delayed refs to run, but
__btrfs_run_delayed_refs really only checks every time we need a new
delayed ref head, so we always run at least one ref head completely no
matter what the number of items on it. Fix the accounting to only be
adjusted when we add/remove a ref head.
In addition to using this number to limit the number of delayed refs
run, a future patch is also going to use it to calculate the amount of
space required for delayed refs space reservation.
Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can have a lot freed extents during the life span of transaction, so
the red black tree that keeps track of the ranges of each freed extent
(fs_info->freed_extents[]) can get quite big. When finishing a
transaction commit we find each range, process it (discard the extents,
unpin them) and then remove it from the red black tree.
We can use an extent state record as a cache when searching for a range,
so that when we clean the range we can use the cached extent state we
passed to the search function instead of iterating the red black tree
again. Doing things as fast as possible when finishing a transaction (in
state TRANS_STATE_UNBLOCKED) is convenient as it reduces the time we
block another task that wants to commit the next transaction.
So change clear_extent_dirty() to allow an optional extent state record to
be passed as an argument, which will be passed down to __clear_extent_bit.
Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device-replace needs to check the result code of the scrub workers
in btrfs_dev_replace_cancel and distinguish if successful cancel
operation and when the there was no operation running.
If btrfs_scrub_cancel() fails, return
BTRFS_IOCTL_DEV_REPLACE_RESULT_NOT_STARTED so that user can try
to cancel the replace again.
Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
RAID5 and RAID6 profile store one copy of the data, not 2 or 3. These
values are not yet used anywhere so there's no change.
Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before btrfs_map_bio submits all stripe bios it does a number of checks
to ensure the device for every stripe is present. However, it doesn't do
a DEV_STATE_MISSING check, instead this is relegated to the lower level
btrfs_schedule_bio (in the async submission case, sync submission
doesn't check DEV_STATE_MISSING at all). Additionally
btrfs_schedule_bios does the duplicate device->bdev check which has
already been performed in btrfs_map_bio.
This patch moves the DEV_STATE_MISSING check in btrfs_map_bio and
removes the duplicate device->bdev check. Doing so ensures that no bio
cloning/submission happens for both async/sync requests in the face of
missing device. This makes the async io submission path slightly shorter
in terms of instruction count. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.
If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.
This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.
Cc: Johan Hovold <johan@kernel.org> Cc: Ladislav Michl <ladis@linux-mips.org> Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The opcodes used by the controller when doing batched page prog should
be written in NFC_REG_WCMD_SET not FC_REG_RCMD_SET. Luckily, the
default NFC_REG_WCMD_SET value matches the one we set in the driver
which explains why we didn't notice the problem.
Fixes: 614049a8d904 ("mtd: nand: sunxi: add support for DMA assisted operations") Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On errors, if we don't stop the descriptor chain, it may continue to
run and raise IRQ after we have called mmc_request_done(). This is bad
because we won't be able to get cmd anymore and properly deal with the
IRQ.
This patch makes sure the descriptor chain is stopped before
calling mmc_request_done()
The old code always starts from fixed port for VMADDR_PORT_ANY. Sometimes
when VMM crashed, there is still orphaned vsock which is waiting for
close timer, then it could cause connection time out for new started VM
if they are trying to connect to same port with same guest cid since the
new packets could hit that orphaned vsock. We could also fix this by doing
more in vhost_vsock_reset_orphans, but any way, it should be better to start
from a random local port instead of a fixed one.
Signed-off-by: Lepton Wu <ytht.net@gmail.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
listen fails when more than one tls capable device is
registered. tls_hw_hash is called for each dev which loops
again for each cdev_list causing listen failure. Hence
call chtls_listen_start/stop for specific device than loop over all
devices.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It should not have been selected for a stable kernel as it breaks the
nVMX regression tests.
Reported-by: Jack Wang <jack.wang.usish@gmail.com> Reported-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Sean Christopherson <sean.j.christopherson@intel.com> Cc: Jim Mattson <jmattson@google.com> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should not have been selected for a stable kernel as it breaks the
nVMX regression tests.
Reported-by: Jack Wang <jack.wang.usish@gmail.com> Reported-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Jim Mattson <jmattson@google.com> Cc: Sean Christopherson <sean.j.christopherson@intel.com> Cc: Jim Mattson <jmattson@google.com> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RDTSCP is supported in legacy mode as well as long mode. The
IA32_TSC_AUX MSR should be set to the correct guest value before
entering any guest that supports RDTSCP.
Fixes: 4e47c7a6d714 ("KVM: VMX: Add instruction rdtscp support for guest") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Peter Shier <pshier@google.com> Reviewed-by: Marc Orr <marcorr@google.com> Reviewed-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If CONFIG_GPOILIB is not set, the stub of gpio_to_desc() should return
the same type of error as regular version: NULL. All the callers
compare the return value of gpio_to_desc() against NULL, so returned
ERR_PTR would be treated as non-error case leading to dereferencing of
error value.
The PCAL_PINCTRL_MASK is too large. The extended register block on
PCAL6524, which is the largest chip with this block, has the block
limited to address range 0x40..0x7f. This is because the bit 7 in
the command register is used for the Address Increment functionality.
Trim the mask to 0x60 to match the datasheet and to prevent accidental
overwrite of the AI bit.
When removing the driver, the following flow can happen:
1. host command is in progress, for example at index 68.
2. RX interrupt is received with the response.
3. Before it is processed, the remove flow kicks in, and
calls iwl_pcie_txq_unmap. The function cleans all DMA,
and promotes the read pointer to 69.
4. RX thread proceeds with the processing, and is calling
iwl_pcie_cmdq_reclaim, which will print this error:
iwl_pcie_cmdq_reclaim: Read index for DMA queue txq id (0),
index 4 is out of range [0-256] 69 69.
Detect this situation, and avoid the print. Change it to
warning while at it, to make such issues more noticeable
in the future.
When traffic load is not low or low latency is active, TCM schedules
re-evaluation work so in case traffic stops TCM will detect that
traffic load has become low or that low latency is no longer active.
However, if TCM is paused when the re-evaluation work runs, it does
not re-evaluate and the re-evaluation work is no longer scheduled.
As a result, TCM will not indicate that low latency is no longer
active or that traffic load is low when traffic stops.
Fix this by forcing TCM re-evaluation when TCM is resumed in case
low latency is active or traffic load is not low.
This function is only half-used by mvm (i.e. only the nvm_version part
matters, since the calibration version is irrelevant), so it's
pointless to export it from iwlwifi. If mvm uses this function, it
has the additional complexity of setting the calib version to a bogus
value on all cfg structs.
To avoid this, move the function to dvm and make a simple comparison
of the nvm_version in mvm instead.
The first issue is the breakage of linux.bin.ub target since commit ece97f3a5fb5 ("microblaze: Fix simpleImage format generation")
because the addition of UIMAGE_{IN,OUT} affected it.
make ARCH=microblaze CROSS_COMPILE=microblaze-linux- linux.bin.ub
[ snip ]
OBJCOPY arch/microblaze/boot/linux.bin
UIMAGE arch/microblaze/boot/linux.bin.ub.ub
/usr/bin/mkimage: Can't open arch/microblaze/boot/linux.bin.ub: No such file or directory
make[1]: *** [arch/microblaze/boot/Makefile;14: arch/microblaze/boot/linux.bin.ub] Error 1
make: *** [arch/microblaze/Makefile;83: linux.bin.ub] Error 2
The second issue is the use of the "if_changed" multiple times for
the same target.
As commit 92a4728608a8 ("x86/boot: Fix if_changed build flip/flop bug")
pointed out, this never works properly. Moreover, generating multiple
images as a side-effect is confusing.
Let's split the build recipe for each image.
simpleImage.<dt>*.unstrip is just a copy of vmlinux.
simpleImage.<dt> and simpleImage.<dt>.ub are created in the same way
as linux.bin and linux.bin.ub, respectively.
I kept simpleImage.* recipes independent of linux.bin.* ones to not
change the behavior.
Lastly, this commit fixes "make ARCH=microblaze clean". Previously,
it only cleaned up the unstrip image. Now, all the simpleImage files
are cleaned.
"make ARCH=microblaze help" mentions simpleImage.<dt>.unstrip,
but it is not a real Make target. It does not work because Makefile
assumes "system.unstrip" is the name of DT.
$ make ARCH=microblaze CROSS_COMPILE=microblaze-linux- simpleImage.system.unstrip
[ snip ]
make[1]: *** No rule to make target 'arch/microblaze/boot/dts/system.unstrip.dtb', needed by 'arch/microblaze/boot/dts/system.dtb'. Stop.
make: *** [Makefile;1060: arch/microblaze/boot/dts] Error 2
make: *** Waiting for unfinished jobs....
simpleImage.<dt> works like a phony target that generates multiple
images. Reflect the real behavior. I removed the DT directory path
information because it is already explained a few lines below.
While I am here, I deleted the redundant *_defconfig explanation.
The top-level Makefile caters to list available defconfig files:
mmu_defconfig - Build for mmu
nommu_defconfig - Build for nommu
The UBI device reference is dropped but then the device is used as a
parameter of ubi_err. The bug is introduced in changing ubi_err's
behavior. The old ubi_err does not require a UBI device as its first
parameter, but the new one does.
Fixes: 32608703310 ("UBI: Extend UBI layer debug/messaging capabilities") Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MTD device reference is dropped via put_mtd_device, however its
field ->index is read and passed to ubi_msg. To fix this, the patch
moves the reference dropping after calling ubi_msg.
Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
When ubifs is build without the LZO compressor and no compressor is
given the creation of the default file system will fail. before
selection the LZO compressor check if it is present and if not fall back
to the zlib or none.
Since mkfs always formats the filesystem with the realtime bitmap and
summary inodes immediately after the root directory, we should expect
that both of them are present and loadable, even if there isn't a
realtime volume attached. There's no reason to skip this if rbmino ==
NULLFSINO; in fact, this causes an immediate crash if the there /is/ a
realtime volume and someone writes to it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Bill O'Donnell <billodo@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A fresh backing device is not attached to any cache_set, and
has no writeback kthread created until first attached to some
cache_set.
But bch_cached_dev_writeback_init run
"
dc->writeback_running = true;
WARN_ON(test_and_clear_bit(BCACHE_DEV_WB_RUNNING,
&dc->disk.flags));
"
for any newly formatted backing devices.
For a fresh standalone backing device, we can get something like
following even if no writeback kthread created:
------------------------
/sys/block/bcache0/bcache# cat writeback_running
1
/sys/block/bcache0/bcache# cat writeback_rate_debug
rate: 512.0k/sec
dirty: 0.0k
target: 0.0k
proportional: 0.0k
integral: 0.0k
change: 0.0k/sec
next io: -15427384ms
The none ZERO fields are misleading as no alive writeback kthread yet.
Set dc->writeback_running false as no writeback thread created in
bch_cached_dev_writeback_init().
We have writeback thread created and woken up in bch_cached_dev_writeback
_start(). Set dc->writeback_running true before bch_writeback_queue()
called, as a writeback thread will check if dc->writeback_running is true
before writing back dirty data, and hung if false detected.
After the change, we can get the following output for a fresh standalone
backing device:
-----------------------
/sys/block/bcache0/bcache$ cat writeback_running
0
/sys/block/bcache0/bcache# cat writeback_rate_debug
rate: 0.0k/sec
dirty: 0.0k
target: 0.0k
proportional: 0.0k
integral: 0.0k
change: 0.0k/sec
next io: 0ms
v1 -> v2:
Set dc->writeback_running before bch_writeback_queue() called,
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
entry is released via usb_put_urb just after calling usb_submit_urb.
However, entry is used if the submission fails, resulting in a use after
free bug. The patch fixes this.
Signed-off-by: Pan Bian <bianpan2016@163.com> ACKed-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & sdio device RX FIFO watermark should be
configured to avoid overflow errors.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two defects: (1) passing a NULL bss to
mwifiex_save_hidden_ssid_channels will result in NULL dereference,
(2) using bss after dropping the reference to it via cfg80211_put_bss.
To fix them, the patch moves the buggy code to the branch that bss is
not NULL and puts it before cfg80211_put_bss.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
CRYPTO_MSG_GETALG in NLM_F_DUMP mode sometimes doesn't return all
registered crypto algorithms, because it doesn't support incremental
dumps. crypto_dump_report() only permits itself to be called once, yet
the netlink subsystem allocates at most ~64 KiB for the skb being dumped
to. Thus only the first recvmsg() returns data, and it may only include
a subset of the crypto algorithms even if the user buffer passed to
recvmsg() is large enough to hold all of them.
Fix this by using one of the arguments in the netlink_callback structure
to keep track of the current position in the algorithm list. Then
userspace can do multiple recvmsg() on the socket after sending the dump
request. This is the way netlink dumps work elsewhere in the kernel;
it's unclear why this was different (probably just an oversight).
Also fix an integer overflow when calculating the dump buffer size hint.
Fixes: a38f7907b926 ("crypto: Add userspace configuration API") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Until now there is no way to reset a AP queue or card. Driving a card
or queue offline and online again does only toggle the 'software'
online state. The only way to trigger a (hardware) reset is by running
hot-unplug/hot-plug for example on the HMC.
This patch makes the queue reset attribute in sysfs writable.
Writing into this attribute triggers a reset on the AP queue's state
machine. So the AP queue is flushed and state machine runs through the
initial states which cause a reset (PQAP(RAPQ)) and a re-registration
to interrupts (PQAP(AQIC)) if available.
The reset sysfs attribute is writable by root only. So only an
administrator is allowed to initiate a reset of AP queues. Please note
that the queue's counter values are left untouched by the reset.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When boxes are run near (or to) OOM, we have a problem with the discard
page allocation in nvme. If we fail allocating the special page, we
return busy, and it'll get retried. But since ordering is honored for
dispatch requests, we can keep retrying this same IO and failing. Behind
that IO could be requests that want to free memory, but they never get
the chance.
Allocate a fixed discard page per controller for a safe fallback, and use
that if the initial allocation fails.
Signed-off-by: Jens Axboe <axboe@kernel.dk> Reviewed-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes NVMe discovery by setting SKIP_PRLI flag, so that PRLI is
driven by driver and is retried when the NPIV port is detected to have NVMe
capability.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.
Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ignore acpi_device_fix_up_power() return value. If we return an error
we end up with acpi_default_enumeration() still creating a platform-
device for the device and we end up with the device still being used
but without the special LPSS related handling which is not useful.
Specicifically ignoring the error fixes the touchscreen no longer
working after a suspend/resume on a Prowise PT301 tablet.
This tablet has a broken _PS0 method on the touchscreen's I2C controller,
causing acpi_device_fix_up_power() to fail, causing fallback to standard
platform-dev handling and specifically causing acpi_lpss_save/restore_ctx
to not run.
The I2C controllers _PS0 method does actually turn on the device, but then
does some more nonsense which fails when run during early boot trying to
use I2C opregion handling on another not-yet registered I2C controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
WARNING: vmlinux.o(.text+0x13250): Section mismatch in reference from the function acs5k_i2c_init() to the (unknown reference) .init.data:(unknown)
The function acs5k_i2c_init() references
the (unknown reference) __initdata (unknown).
This is often because acs5k_i2c_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
A log recovery failure has been reproduced where a symlink inode has
a zero length in extent form. It was caused by a shutdown during a
combined fstress+fsmark workload.
The underlying problem is the issue in xfs_inactive_symlink(): the
inode is unlocked between the symlink inactivation/truncation and
the inode being freed. This opens a window for the inode to be
written to disk before it xfs_ifree() removes it from the unlinked
list, marks it free in the inobt and zeros the mode.
For shortform inodes, the fix is simple. xfs_ifree() clears the data
fork state, so there's no need to do it in xfs_inactive_symlink().
This means the shortform fork verifier will not see a zero length
data fork as it mirrors the inode size through to xfs_ifree()), and
hence if the inode gets written back and the fork verifiers are run
they will still see a fork that matches the on-disk inode size.
For extent form (remote) symlinks, it is a little more tricky. Here
we explicitly set the inode size to zero, so the above race can lead
to zero length symlinks on disk. Because the inode is unlinked at
this point (i.e. on the unlinked list) and unreferenced, it can
never be seen again by a user. Hence when we set the inode size to
zeor, also change the type to S_IFREG. xfs_ifree() expects S_IFREG
inodes to be of zero length, and so this avoids all the problems of
zero length symlinks ever hitting the disk. It also avoids the
problem of needing to handle zero length symlink inodes in log
recovery to replay the extent free intents and the remaining
deferops to free the extents the symlink used.
Also add a couple of asserts to warn us if zero length symlinks end
up in either the symlink create or inactivation paths.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 396244692232 ("arm64: preempt: Provide our own implementation of
asm/preempt.h") extended the preempt count field in struct thread_info
to 64 bits, so that it consists of a 32-bit count plus a 32-bit flag
indicating whether or not the current task needs rescheduling.
Whilst the asm-offsets definition of TSK_TI_PREEMPT was updated to point
to this new field, the assembly usage was left untouched meaning that a
32-bit load from TSK_TI_PREEMPT on a big-endian machine actually returns
the reschedule flag instead of the count.
Whilst we could fix this by pointing TSK_TI_PREEMPT at the count field,
we're actually better off reworking the two assembly users so that they
operate on the whole 64-bit value in favour of inspecting the thread
flags separately in order to determine whether a reschedule is needed.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reported-by: "kernelci.org bot" <bot@kernelci.org> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we do USB configuration only if the host mode (CONFIG_USB)
is enabled. But it should be done also in the case of device-only setups,
so change the condition to CONFIG_USB_SUPPORT. This allows to use
omap_udc on Palm Tungsten E.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Exchange LED configuration between msn201x and next generation systems
types.
Bug was introduced when LED driver activation was added to mlx-platform.
LED configuration for the three new system MQMB7, MSN37, MSN34 was
assigned to MSN21 and vice versa. This bug affects MSN21 only and
likely requires backport to v4.19.
With ti-sysc, we need to now have the device tree properties for
ti,no-reset-on-init and ti,no-idle-on-init at the module level instead
of the child device level.
Let's check for these properties at the child device level to enable
quirks, and warn about moving the properties to the module level.
Otherwise am335x-evm based boards tagging gpio1 with ti,no-reset-on-init
will have their DDR power disabled if wired up in such a tricky way.
Note that this should not be an issue for earlier kernels as we don't
rely on this until the dts files have been updated to probe with ti-sysc
interconnect target driver.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The __cpu_up() routine ignores the errors reported by the firmware
for a CPU bringup operation and looks for the error status set by the
booting CPU. If the CPU never entered the kernel, we could end up
in assuming stale error status, which otherwise would have been
set/cleared appropriately by the booting CPU.
Reported-by: Steve Capper <steve.capper@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For cases where there is a mismatch in ARMv8.2-LVA support between CPUs
we have to be careful in allowing secondary CPUs to boot if 52-bit
virtual addresses have already been enabled on the boot CPU.
This patch adds code to the secondary startup path. If the boot CPU has
enabled 52-bit VAs then ID_AA64MMFR2_EL1 is checked to see if the
secondary can also enable 52-bit support. If not, the secondary is
prevented from booting and an error message is displayed indicating why.
Technically this patch could be implemented using the cpufeature code
when considering 52-bit userspace support. However, we employ low level
checks here as the cpufeature code won't be able to run if we have
mismatched 52-bit kernel va support.
Signed-off-by: Steve Capper <steve.capper@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
