In dasd_profile_start() the amount of requests on the device queue are
counted. The access to the device queue is unprotected against
concurrent access. With a lot of parallel I/O, especially with alias
devices enabled, the device queue can change while dasd_profile_start()
is accessing the queue. In the worst case this leads to a kernel panic
due to incorrect pointer accesses.
Fix this by taking the device lock before accessing the queue and
counting the requests. Additionally the check for a valid profile data
pointer can be done earlier to avoid unnecessary locking in a hot path.
In order for `AT_EMPTY_PATH` to work as expected, the fact
that the user wants that behavior needs to make it to `getname_flags`
or it will return ENOENT.
The crash occurred when call wake_up(&state->wait), and then we want
to look at the value in the state. However, bch_sectors_dirty_init()
is not found in the stack of any task. Since state is allocated on
the stack, we guess that bch_sectors_dirty_init() has exited, causing
bch_dirty_init_thread() to be unable to handle kernel paging request.
In order to verify this idea, we added some printing information during
wake_up(&state->wait). We find that "wake up" is printed twice, however
we only expect the last thread to wake up once.
```dmesg
[ 994.641004] alcache: bch_dirty_init_thread() wake up
[ 994.641018] alcache: bch_dirty_init_thread() wake up
[ 994.641523] alcache: bch_sectors_dirty_init() init exit
```
There is a race. If bch_sectors_dirty_init() exits after the first wake
up, the second wake up will trigger this bug("unable to handle kernel
paging request").
We believe it is very common to wake up twice if there is no dirty, but
crash is an extremely low probability event. It's hard for us to reproduce
this issue. We attached and detached continuously for a week, with a total
of more than one million attaches and only one crash.
Putting atomic_inc(&state.started) before kthread_run() can avoid waking
up twice.
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded") Signed-off-by: Mingzhe Zou <mingzhe.zou@easystack.cn> Cc: <stable@vger.kernel.org> Signed-off-by: Coly Li <colyli@suse.de> Link: https://lore.kernel.org/r/20231120052503.6122-8-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
md_end_clone_io() may overwrite error status in orig_bio->bi_status with
BLK_STS_OK. This could happen when orig_bio has BIO_CHAIN (split by
md_submit_bio => bio_split_to_limits, for example). As a result, upper
layer may miss error reported from md (or the device) and consider the
failed IO was successful.
Fix this by only update orig_bio->bi_status when current bio reports
error and orig_bio is BLK_STS_OK. This is the same behavior as
__bio_chain_endio().
Fixes: 10764815ff47 ("md: add io accounting for raid0 and raid5") Cc: stable@vger.kernel.org # v5.14+ Reported-by: Bhanu Victor DiCara <00bvd0+linux@gmail.com> Closes: https://lore.kernel.org/regressions/5727380.DvuYhMxLoT@bvd0/ Signed-off-by: Song Liu <song@kernel.org> Tested-by: Xiao Ni <xni@redhat.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At line 35 the original r[nodes].b is not always allocatored from
__bch_btree_node_alloc(), and possibly initialized as NULL pointer by
caller of btree_gc_coalesce(). Therefore the change at line 36 is not
correct.
This patch replaces the mistaken IS_ERR() by IS_ERR_OR_NULL() to avoid
potential issue.
Fixes: 028ddcac477b ("bcache: Remove unnecessary NULL point check in node allocations") Cc: <stable@vger.kernel.org> # 6.5+ Cc: Zheng Wang <zyytlz.wz@163.com> Signed-off-by: Coly Li <colyli@suse.de> Link: https://lore.kernel.org/r/20231120052503.6122-9-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bug that when using the XEN hypervisor with bios with large
multi-page bio vectors on NVMe, the kernel deadlocks [1].
The deadlocks are caused by inability to map a large bio vector -
dma_map_sgtable always returns an error, this gets propagated to the block
layer as BLK_STS_RESOURCE and the block layer retries the request
indefinitely.
XEN uses the swiotlb framework to map discontiguous pages into contiguous
runs that are submitted to the PCIe device. The swiotlb framework has a
limitation on the length of a mapping - this needs to be announced with
the max_mapping_size method to make sure that the hardware drivers do not
create larger mappings.
Without max_mapping_size, the NVMe block driver would create large
mappings that overrun the maximum mapping size.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Link: https://lore.kernel.org/stable/ZTNH0qtmint%2FzLJZ@mail-itl/ Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Suggested-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Acked-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/151bef41-e817-aea9-675-a35fdac4ed@redhat.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like various other ASUS ExpertBook-s, the ASUS ExpertBook B1402CVA
has an ACPI DSDT table that describes IRQ 1 as ActiveLow while
the kernel overrides it to EdgeHigh.
This prevents the keyboard from working. To fix this issue, add this laptop
to the skip_override_table so that the kernel does not override IRQ 1.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218114 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that checks for unknown boot options is unaware of the sysctl
alias facility, which maps bootparams to sysctl values. If a user sets
an old value that has a valid alias, a message about an invalid
parameter will be printed during boot, and the parameter will get passed
to init. Fix by checking for the existence of aliased parameters in the
unknown boot parameter code. If an alias exists, don't return an error
or pass the value to init.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com> Cc: stable@vger.kernel.org Fixes: 0a477e1ae21b ("kernel/sysctl: support handling command line aliases") Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Krister Johansen <kjlx@templeofstupid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__insert_pending() allocate memory in atomic context, so the allocation
could fail, but we are not handling that failure now. It could lead
ext4_es_remove_extent() to get wrong reserved clusters, and the global
data blocks reservation count will be incorrect. The same to
extents_status entry preallocation, preallocate pending entry out of the
i_es_lock with __GFP_NOFAIL, make sure __insert_pending() and
__revise_pending() always succeeds.
Yikebaer reported an issue:
==================================================================
BUG: KASAN: slab-use-after-free in ext4_es_insert_extent+0xc68/0xcb0
fs/ext4/extents_status.c:894
Read of size 4 at addr ffff888112ecc1a4 by task syz-executor/8438
The flow of issue triggering is as follows:
1. remove es
raw es es removed es1
|-------------------| -> |----|.......|------|
2. insert es
es insert es1 merge with es es1 merge with es and free es1
|----|.......|------| -> |------------|------| -> |-------------------|
es merges with newes, then merges with es1, frees es1, then determines
if es1->es_len is 0 and triggers a UAF.
The code flow is as follows:
ext4_es_insert_extent
es1 = __es_alloc_extent(true);
es2 = __es_alloc_extent(true);
__es_remove_extent(inode, lblk, end, NULL, es1)
__es_insert_extent(inode, &newes, es1) ---> insert es1 to es tree
__es_insert_extent(inode, &newes, es2)
ext4_es_try_to_merge_right
ext4_es_free_extent(inode, es1) ---> es1 is freed
if (es1 && !es1->es_len)
// Trigger UAF by determining if es1 is used.
We determine whether es1 or es2 is used immediately after calling
__es_remove_extent() or __es_insert_extent() to avoid triggering a
UAF if es1 or es2 is freed.
Reported-by: Yikebaer Aizezi <yikebaer61@gmail.com> Closes: https://lore.kernel.org/lkml/CALcu4raD4h9coiyEBL4Bm0zjDwxC2CyPiTwsP3zFuhot6y9Beg@mail.gmail.com Fixes: 2a69c450083d ("ext4: using nofail preallocation in ext4_es_insert_extent()") Cc: stable@kernel.org Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230815070808.3377171-1-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to in ext4_es_insert_delayed_block(), we use preallocations that
do not fail to avoid inconsistencies, but we do not care about es that are
not must be kept, and we return 0 even if such es memory allocation fails.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-9-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to in ext4_es_remove_extent(), we use a no-fail preallocation
to avoid inconsistencies, except that here we may have to preallocate
two extent_status.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-8-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
If __es_remove_extent() returns an error it means that when splitting
extent, allocating an extent that must be kept failed, where returning
an error directly would cause the extent tree to be inconsistent. So we
use GFP_NOFAIL to pre-allocate an extent_status and pass it to
__es_remove_extent() to avoid this problem.
In addition, since the allocated memory is outside the i_es_lock, the
extent_status tree may change and the pre-allocated extent_status is
no longer needed, so we release the pre-allocated extent_status when
es->es_len is not initialized.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-7-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
When splitting extent, if the second extent can not be dropped, we return
-ENOMEM and use GFP_NOFAIL to preallocate an extent_status outside of
i_es_lock and pass it to __es_remove_extent() to be used as the second
extent. This ensures that __es_remove_extent() is executed successfully,
thus ensuring consistency in the extent status tree. If the second extent
is not undroppable, we simply drop it and return 0. Then retry is no longer
necessary, remove it.
Now, __es_remove_extent() will always remove what it should, maybe more.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-6-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Pass a extent_status pointer prealloc to __es_insert_extent(). If the
pointer is non-null, it is used directly when a new extent_status is
needed to avoid memory allocation failures.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-5-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Factor out __es_alloc_extent() and __es_free_extent(), which only allocate
and free extent_status in these two helpers.
The ext4_es_alloc_extent() function is split into __es_alloc_extent()
and ext4_es_init_extent(). In __es_alloc_extent() we allocate memory using
GFP_KERNEL | __GFP_NOFAIL | __GFP_ZERO if the memory allocation cannot
fail, otherwise we use GFP_ATOMIC. and the ext4_es_init_extent() is used to
initialize extent_status and update related variables after a successful
allocation.
This is to prepare for the use of pre-allocated extent_status later.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-4-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
In the extent status tree, we have extents which we can just drop without
issues and extents we must not drop - this depends on the extent's status
- currently ext4_es_is_delayed() extents must stay, others may be dropped.
A helper function is added to help determine if the current extent can
be dropped, although only ext4_es_is_delayed() extents cannot be dropped
currently.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-3-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).
CSID hardware on SM8250 can demux up to 4 simultaneous streams
based on virtual channel (vc) or datatype (dt).
The CSID subdevice entity now has 4 source ports that can be
enabled/disabled and thus can control which virtual channels
are enabled. Datatype demuxing not tested.
In order to keep a valid internal state of the subdevice,
implicit format propagation from the sink to the source pads
has been preserved. However, the format on each source pad
can be different and in that case it must be configured explicitly.
CSID's s_stream is called when any stream is started or stopped.
It will call configure_streams() that will rewrite IRQ settings to HW.
When multiple streams are running simultaneously there is an issue
when writing IRQ settings for one stream while another is still
running, thus avoid re-writing settings if they were not changed
in link setup, or by fully powering off the CSID hardware.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Acked-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stable-dep-of: e655d1ae9703 ("media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3") Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernel test robot reported below warning ->
drivers/media/platform/qcom/camss/camss-csid-gen2.c:407:3:
warning: Value stored to 'val' is never read
[clang-analyzer-deadcode.DeadStores]
Replace hard coded value with val.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stable-dep-of: e655d1ae9703 ("media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3") Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 411740f5422a ("KVM: MIPS/MMU: Implement KVM_CAP_SYNC_MMU")
old_pte is no longer used in kvm_mips_map_page(). So remove it to fix a
build warning about variable set but not used:
arch/mips/kvm/mmu.c: In function 'kvm_mips_map_page':
>> arch/mips/kvm/mmu.c:701:29: warning: variable 'old_pte' set but not used [-Wunused-but-set-variable]
701 | pte_t *ptep, entry, old_pte;
| ^~~~~~~
Kent reported an occasional KASAN splat in lockdep. Mark then noted:
> I suspect the dodgy access is to chain_block_buckets[-1], which hits the last 4
> bytes of the redzone and gets (incorrectly/misleadingly) attributed to
> nr_large_chain_blocks.
That would mean @size == 0, at which point size_to_bucket() returns -1
and the above happens.
alloc_chain_hlocks() has 'size - req', for the first with the
precondition 'size >= rq', which allows the 0.
This code is trying to split a block, del_chain_block() takes what we
need, and add_chain_block() puts back the remainder, except in the
above case the remainder is 0 sized and things go sideways.
Fixes: 810507fe6fd5 ("locking/lockdep: Reuse freed chain_hlocks entries") Reported-by: Kent Overstreet <kent.overstreet@linux.dev> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Kent Overstreet <kent.overstreet@linux.dev> Link: https://lkml.kernel.org/r/20231121114126.GH8262@noisy.programming.kicks-ass.net Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cfb5 ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()") Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver") Cc: stable@vger.kernel.org # 4.18 Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Lee Jones <lee@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 9cf87666fc6e ("USB: dwc3: qcom: fix ACPI platform device leak") Signed-off-by: Sasha Levin <sashal@kernel.org>
The host and subsystem NQNs are passed in the connect command payload and
interpreted as nul-terminated strings. Ensure they actually are
nul-terminated before using them.
Fixes: a07b4970f464 "nvmet: add a generic NVMe target") Reported-by: Alon Zahavi <zahavi.alon@gmail.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
AFS doesn't really do locking on R/O volumes as fileservers don't maintain
state with each other and thus a lock on a R/O volume file on one
fileserver will not be be visible to someone looking at the same file on
another fileserver.
Further, the server may return an error if you try it.
Fix this by doing what other AFS clients do and handle filelocking on R/O
volume files entirely within the client and don't touch the server.
Fixes: 6c6c1d63c243 ("afs: Provide mount-time configurable byte-range file locking emulation") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a6f ("octeontx2-pf: Add support for ethtool ntuple filters") Signed-off-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is quite obvious that this is a SMC DECLINE message, which means that
the applications received SMC protocol message.
We found that this was caused by the following situations:
As a result, a decline message was sent in the implementation, and this
message was read from TCP by the already-fallback connection.
This patch double the client timeout as 2x of the server value,
With this simple change, the Decline messages should never cross or
collide (during Confirm link timeout).
This issue requires an immediate solution, since the protocol updates
involve a more long-term solution.
Fixes: 0fb0b02bd6fd ("net/smc: adapt SMC client code to use the LLC flow") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Wen Gu <guwen@linux.alibaba.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Reported-by: Herb Wei <weihao.bj@ieisystem.com> Tested-by: Herb Wei <weihao.bj@ieisystem.com> Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
hid_debug_events_release releases resources bound to the HID device instance.
hid_device_release releases the underlying HID device instance potentially
before hid_debug_events_release has completed releasing debug resources bound
to the same HID device instance.
Reference count to prevent the HID device instance from being torn down
preemptively when HID debugging support is used. When count reaches zero,
release core resources of HID device instance using hiddev_free.
This unique identifier is currently used only for ensuring uniqueness in
sysfs. However, this could be handful for userspace to refer to a specific
hid_device by this id.
2 use cases are in my mind: LEDs (and their naming convention), and
HID-BPF.
During 'ifconfig <netdev> down' one RSS memory was not getting freed.
This patch fixes the same.
Fixes: 81a4362016e7 ("octeontx2-pf: Add RSS multi group support") Signed-off-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
wg_xmit() can be called concurrently, KCSAN reported [1]
some device stats updates can be lost.
Use DEV_STATS_INC() for this unlikely case.
[1]
BUG: KCSAN: data-race in wg_xmit / wg_xmit
read-write to 0xffff888104239160 of 8 bytes by task 1375 on cpu 0:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
read-write to 0xffff888104239160 of 8 bytes by task 1378 on cpu 1:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
v2: also change wg_packet_consume_data_done() (Hangbin Liu)
and wg_packet_purge_staged_packets()
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Innolux G101ICE-L01 datasheet [1] page 17 table
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
indicates that maximum vertical blanking time is 40 lines.
Currently the driver uses 29 lines.
Fix it, and since this panel is a DE panel, adjust the timings
to make them less hostile to controllers which cannot do 1 px
HSA/VSA, distribute the delays evenly between all three parts.
For "boe,tv105wum-nw0" this special panel, it is stipulated in
the panel spec that MIPI needs to keep the LP11 state before
the lcm_reset pin is pulled high.
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230515094955.15982-3-shuijing.li@mediatek.com
Stable-dep-of: 6965809e5269 ("drm/panel: auo,b101uan08.3: Fine tune the panel power sequence") Signed-off-by: Sasha Levin <sashal@kernel.org>
When kafs tries to look up a cell in the DNS or the local config, it will
translate a lookup failure into EDESTADDRREQ whereas OpenAFS translates it
into ENOENT. Applications such as West expect the latter behaviour and
fail if they see the former.
This can be seen by trying to mount an unknown cell:
# mount -t afs %example.com:cell.root /mnt
mount: /mnt: mount(2) system call failed: Destination address required.
Fixes: 4d673da14533 ("afs: Support the AFS dynamic root") Reported-by: Markus Suvanto <markus.suvanto@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216637 Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes a bug in commit 9ed9895370ae ("driver core: Functional
dependencies tracking support") where the device link status was
incorrectly updated in the driver unbind path before all the device's
resources were released.
Fixes: 9ed9895370ae ("driver core: Functional dependencies tracking support") Cc: stable <stable@kernel.org> Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Closes: https://lore.kernel.org/all/20231014161721.f4iqyroddkcyoefo@pengutronix.de/ Signed-off-by: Saravana Kannan <saravanak@google.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mark Brown <broonie@kernel.org> Cc: Matti Vaittinen <mazziesaccount@gmail.com> Cc: James Clark <james.clark@arm.com> Acked-by: "Rafael J. Wysocki" <rafael@kernel.org> Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20231018013851.3303928-1-saravanak@google.com Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Change directory to the tracefs directory
2. Create a kprobe event (doesn't matter what one)
3. Open bash file descriptor 5 on the enable file of the kprobe event
4. Delete the kprobe event (removes the files too)
5. Close the bash file descriptor 5
What happens here is that the kprobe event creates a trace_event_file
"file" descriptor that represents the file in tracefs to the event. It
maintains state of the event (is it enabled for the given instance?).
Opening the "enable" file gets a reference to the event "file" descriptor
via the open file descriptor. When the kprobe event is deleted, the file is
also deleted from the tracefs system which also frees the event "file"
descriptor.
But as the tracefs file is still opened by user space, it will not be
totally removed until the final dput() is called on it. But this is not
true with the event "file" descriptor that is already freed. If the user
does a write to or simply closes the file descriptor it will reference the
event "file" descriptor that was just freed, causing a use-after-free bug.
To solve this, add a ref count to the event "file" descriptor as well as a
new flag called "FREED". The "file" will not be freed until the last
reference is released. But the FREE flag will be set when the event is
removed to prevent any more modifications to that event from happening,
even if there's still a reference to the event "file" descriptor.
As reported by Mahesh & Aneesh, opal_prd_msg_notifier() triggers a
FORTIFY_SOURCE warning:
memcpy: detected field-spanning write (size 32) of single field "&item->msg" at arch/powerpc/platforms/powernv/opal-prd.c:355 (size 4)
WARNING: CPU: 9 PID: 660 at arch/powerpc/platforms/powernv/opal-prd.c:355 opal_prd_msg_notifier+0x174/0x188 [opal_prd]
NIP opal_prd_msg_notifier+0x174/0x188 [opal_prd]
LR opal_prd_msg_notifier+0x170/0x188 [opal_prd]
Call Trace:
opal_prd_msg_notifier+0x170/0x188 [opal_prd] (unreliable)
notifier_call_chain+0xc0/0x1b0
atomic_notifier_call_chain+0x2c/0x40
opal_message_notify+0xf4/0x2c0
This happens because the copy is targeting item->msg, which is only 4
bytes in size, even though the enclosing item was allocated with extra
space following the msg.
To fix the warning define struct opal_prd_msg with a union of the header
and a flex array, and have the memcpy target the flex array.
We could race with SQ thread exit, and if we do, we'll hit a NULL pointer
dereference when the thread is cleared. Grab the SQPOLL data lock before
attempting to get the task cpu and pid for fdinfo, this ensures we have a
stable view of it.
[WHY]
Flush command sent to DMCUB spends more time for execution on
a dGPU than on an APU. This causes cursor lag when using high
refresh rate mouses.
[HOW]
1. Change the DMCUB mailbox memory location from FB to inbox.
2. Only change windows memory to inbox.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Lewis Huang <lewis.huang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not leak the pointer where we couldn't grab the reference
on to the caller because it can be that the error handling still
tries to put the reference then.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ATRM ACPI method is for fetching the dGPU vbios rom
image on laptops and all-in-one systems. It should not be
used for external add in cards. If the dGPU is thunderbolt
connected, don't try ATRM.
v2: pci_is_thunderbolt_attached only works for Intel. Use
pdev->external_facing instead.
v3: dev_is_removable() seems to be what we want
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2925 Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The incoming strings might not be terminated by a newline
or a 0.
(found while testing a program that just wrote the string
itself, causing a crash)
Cc: stable@vger.kernel.org Fixes: e3933f26b657 ("drm/amd/pp: Add edit/commit/show OD clock/voltage support in sysfs") Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrong check of gdb backup in meta bg as following:
first_group is the first group of meta_bg which contains target group, so
target group is always >= first_group. We check if target group has gdb
backup by comparing first_group with [group + 1] and [group +
EXT4_DESC_PER_BLOCK(sb) - 1]. As group >= first_group, then [group + N] is
> first_group. So no copy of gdb backup in meta bg is done in
setup_new_flex_group_blocks.
No need to do gdb backup copy in meta bg from setup_new_flex_group_blocks
as we always copy updated gdb block to backups at end of
ext4_flex_group_add as following:
ext4_flex_group_add
/* no gdb backup copy for meta bg any more */
setup_new_flex_group_blocks
/* update current group number */
ext4_update_super
sbi->s_groups_count += flex_gd->count;
/*
* if group in meta bg contains backup is added, the primary gdb block
* of the meta bg will be copy to backup in new added group here.
*/
for (; gdb_num <= gdb_num_end; gdb_num++)
update_backups(...)
In summary, we can remove wrong gdb backup copy code in
setup_new_flex_group_blocks.
When big allocate feature is enabled, we need to count and update
reserved clusters before removing a delayed only extent_status entry.
{init|count|get}_rsvd() have already done this, but the start block
number of this counting isn't correct in the following case.
lblk end
| |
v v
-------------------------
| | orig_es
-------------------------
^ ^
len1 is 0 | len2 |
If the start block of the orig_es entry founded is bigger than lblk, we
passed lblk as start block to count_rsvd(), but the length is correct,
finally, the range to be counted is offset. This patch fix this by
passing the start blocks to 'orig_es->lblk + len1'.
Commit 0aeaa2559d6d5 ("ext4: fix corruption when online resizing a 1K
bigalloc fs") found that primary superblock's offset in its group is
not equal to offset of backup superblock in its group when block size
is 1K and bigalloc is enabled. As group descriptor blocks are right
after superblock, we can't pass block number of gdb to update_backups
for the same reason.
The root casue of the issue above is that leading 1K padding block is
count as data block offset for primary block while backup block has no
padding block offset in its group.
Remove padding data block count to fix the issue for gdb backups.
For meta_bg case, update_backups treat blk_off as block number, do no
conversion in this case.
The function ext4_init_acl() calls posix_acl_create() which is
responsible for applying the umask. But without
CONFIG_EXT4_FS_POSIX_ACL, ext4_init_acl() is an empty inline function,
and nobody applies the umask.
This fixes a bug which causes the umask to be ignored with O_TMPFILE
on ext4:
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
check_clock doesn't account for vfe_lite which means that vfe_lite will
never get validated by this routine. Add the clock name to the expected set
to remediate.
Fixes: 7319cdf189bb ("media: camss: Add support for VFE hardware version Titan 170") Cc: stable@vger.kernel.org Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two problems with the current vfe_disable_output() routine.
Firstly we rightly use a spinlock to protect output->gen2.active_num
everywhere except for in the IDLE timeout path of vfe_disable_output().
Even if that is not racy "in practice" somehow it is by happenstance not
by design.
Secondly we do not get consistent behaviour from this routine. On
sc8280xp 50% of the time I get "VFE idle timeout - resetting". In this
case the subsequent capture will succeed. The other 50% of the time, we
don't hit the idle timeout, never do the VFE reset and subsequent
captures stall indefinitely.
Rewrite the vfe_disable_output() routine to
- Quiesce write masters with vfe_wm_stop()
- Set active_num = 0
remembering to hold the spinlock when we do so followed by
- Reset the VFE
Testing on sc8280xp and sdm845 shows this to be a valid fix.
Fixes: 7319cdf189bb ("media: camss: Add support for VFE hardware version Titan 170") Cc: stable@vger.kernel.org Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now it is possible to do a vfe_get() with the internal reference
count at 1. If vfe_check_clock_rates() returns non-zero then we will
leave the reference count as-is and
vfe_get() should not attempt to roll-back on error when the ref-count is
non-zero as the upper layers will still do their own vfe_put() operations.
vfe_put() will drop the reference count and do the necessary power
domain release, the cleanup jumps in vfe_get() should only be run when
the ref-count is zero.
We need to make sure camss_configure_pd() happens before
camss_register_entities() as the vfe_get() path relies on the pointer
provided by camss_configure_pd().
Fix the ordering sequence in probe to ensure the pointers vfe_get() demands
are present by the time camss_register_entities() runs.
In order to facilitate backporting to stable kernels I've moved the
configure_pd() call pretty early on the probe() function so that
irrespective of the existence of the old error handling jump labels this
patch should still apply to -next circa Aug 2023 to v5.13 inclusive.
Due to a flaw in the hardware design, the GL9750 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9750
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: d7133797e9e1 ("mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2") Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20231107095741.8832-2-victorshihgli@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device that support DASH may be reseted or powered off during suspend.
So driver needs to handle DASH during system suspend and resume. Or
DASH firmware will influence device behavior and causes network lost.
Objcg vectors attached to slab pages to store slab object ownership
information are allocated using gfp flags for the original slab
allocation. Depending on slab page order and the size of slab objects,
objcg vector can take several pages.
If the original allocation was done with the __GFP_NOFAIL flag, it
triggered a warning in the page allocation code. Indeed, order > 1 pages
should not been allocated with the __GFP_NOFAIL flag.
Fix this by simply dropping the __GFP_NOFAIL flag when allocating the
objcg vector. It effectively allows to skip the accounting of a single
slab object under a heavy memory pressure.
An alternative would be to implement the mechanism to fallback to order-0
allocations for accounting metadata, which is also not perfect because it
will increase performance penalty and memory footprint of the kernel
memory accounting under memory pressure.
Link: https://lkml.kernel.org/r/ZUp8ZFGxwmCx4ZFr@P9FQF9L96D.corp.robot.car Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev> Reported-by: Christoph Lameter <cl@linux.com> Closes: https://lkml.kernel.org/r/6b42243e-f197-600a-5d22-56bd728a5ad8@gentwo.org Acked-by: Shakeel Butt <shakeelb@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When GL9750 enters ASPM L1 sub-states, it will stay at L1.1 and will not
enter L1.2. The workaround is to toggle PM state to allow GL9750 to enter
ASPM L1.2.
Initialise the try sink compose rectangle size to the sink compose
rectangle for binner and scaler sub-devices. This was missed due to the
faulty condition that lead to the compose rectangles to be initialised for
the pixel array sub-device where it is not relevant.
The hfi parser, parses the capabilities received from venus firmware and
copies them to core capabilities. Consider below api, for example,
fill_caps - In this api, caps in core structure gets updated with the
number of capabilities received in firmware data payload. If the same api
is called multiple times, there is a possibility of copying beyond the max
allocated size in core caps.
Similar possibilities in fill_raw_fmts and fill_profile_level functions.
Buffer requirement, for different buffer type, comes from video firmware.
While copying these requirements, there is an OOB possibility when the
payload from firmware is more than expected size. Fix the check to avoid
the OOB possibility.
Supported codec bitmask is populated from the payload from venus firmware.
There is a possible case when all the bits in the codec bitmask is set. In
such case, core cap for decoder is filled and MAX_CODEC_NUM is utilized.
Now while filling the caps for encoder, it can lead to access the caps
array beyong 32 index. Hence leading to OOB write.
The fix counts the supported encoder and decoder. If the count is more than
max, then it skips accessing the caps.
When transmitting, infrared drivers expect an odd number of samples; iow
without a trailing space. No problems have been observed so far, so
this is just belt and braces.
Fixes: 9b6192589be7 ("media: lirc: implement scancode sending") Cc: stable@vger.kernel.org Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc and W=1 option, there's a warning like this:
fs/f2fs/compress.c: In function ‘f2fs_init_page_array_cache’:
fs/f2fs/compress.c:1984:47: error: ‘%u’ directive writing between
1 and 7 bytes into a region of size between 5 and 8
[-Werror=format-overflow=]
1984 | sprintf(slab_name, "f2fs_page_array_entry-%u:%u", MAJOR(dev),
MINOR(dev));
| ^~
String "f2fs_page_array_entry-%u:%u" can up to 35. The first "%u" can up
to 4 and the second "%u" can up to 7, so total size is "24 + 4 + 7 = 35".
slab_name's size should be 35 rather than 32.
Cc: stable@vger.kernel.org Signed-off-by: Su Hui <suhui@nfschina.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we set SMBHSTCNT_LAST_BYTE only after the host has started
receiving the last byte. If we get e.g. preempted before setting
SMBHSTCNT_LAST_BYTE, the host may be finished with receiving the byte
before SMBHSTCNT_LAST_BYTE is set.
Therefore change the code to set SMBHSTCNT_LAST_BYTE before writing
SMBHSTSTS_BYTE_DONE for the byte before the last byte. Now the code
is also consistent with what we do in i801_isr_byte_done().
Reported-by: Jean Delvare <jdelvare@suse.com> Closes: https://lore.kernel.org/linux-i2c/20230828152747.09444625@endymion.delvare/ Cc: stable@vger.kernel.org Acked-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27abe ("leds: initial support for Turris Omnia LEDs") Cc: stable@vger.kernel.org Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When LAN9303 is MDIO-connected two callchains exist into
mdio->bus->write():
1. switch ports 1&2 ("physical" PHYs):
virtual (switch-internal) MDIO bus (lan9303_switch_ops->phy_{read|write})->
lan9303_mdio_phy_{read|write} -> mdiobus_{read|write}_nested
2. LAN9303 virtual PHY:
virtual MDIO bus (lan9303_phy_{read|write}) ->
lan9303_virt_phy_reg_{read|write} -> regmap -> lan9303_mdio_{read|write}
If the latter functions just take
mutex_lock(&sw_dev->device->bus->mdio_lock) it triggers a LOCKDEP
false-positive splat. It's false-positive because the first
mdio_lock in the second callchain above belongs to virtual MDIO bus, the
second mdio_lock belongs to physical MDIO bus.
Consequent annotation in lan9303_mdio_{read|write} as nested lock
(similar to lan9303_mdio_phy_{read|write}, it's the same physical MDIO bus)
prevents the following splat:
WARNING: possible circular locking dependency detected
5.15.71 #1 Not tainted
------------------------------------------------------
kworker/u4:3/609 is trying to acquire lock: ffff000011531c68 (lan9303_mdio:131:(&lan9303_mdio_regmap_config)->lock){+.+.}-{3:3}, at: regmap_lock_mutex
but task is already holding lock: ffff0000114c44d8 (&bus->mdio_lock){+.+.}-{3:3}, at: mdiobus_read
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&bus->mdio_lock){+.+.}-{3:3}:
lock_acquire
__mutex_lock
mutex_lock_nested
lan9303_mdio_read
_regmap_read
regmap_read
lan9303_probe
lan9303_mdio_probe
mdio_probe
really_probe
__driver_probe_device
driver_probe_device
__device_attach_driver
bus_for_each_drv
__device_attach
device_initial_probe
bus_probe_device
deferred_probe_work_func
process_one_work
worker_thread
kthread
ret_from_fork
-> #0 (lan9303_mdio:131:(&lan9303_mdio_regmap_config)->lock){+.+.}-{3:3}:
__lock_acquire
lock_acquire.part.0
lock_acquire
__mutex_lock
mutex_lock_nested
regmap_lock_mutex
regmap_read
lan9303_phy_read
dsa_slave_phy_read
__mdiobus_read
mdiobus_read
get_phy_device
mdiobus_scan
__mdiobus_register
dsa_register_switch
lan9303_probe
lan9303_mdio_probe
mdio_probe
really_probe
__driver_probe_device
driver_probe_device
__device_attach_driver
bus_for_each_drv
__device_attach
device_initial_probe
bus_probe_device
deferred_probe_work_func
process_one_work
worker_thread
kthread
ret_from_fork
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&bus->mdio_lock);
lock(lan9303_mdio:131:(&lan9303_mdio_regmap_config)->lock);
lock(&bus->mdio_lock);
lock(lan9303_mdio:131:(&lan9303_mdio_regmap_config)->lock);
*** DEADLOCK ***
5 locks held by kworker/u4:3/609:
#0: ffff000002842938 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work
#1: ffff80000bacbd60 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work
#2: ffff000007645178 (&dev->mutex){....}-{3:3}, at: __device_attach
#3: ffff8000096e6e78 (dsa2_mutex){+.+.}-{3:3}, at: dsa_register_switch
#4: ffff0000114c44d8 (&bus->mdio_lock){+.+.}-{3:3}, at: mdiobus_read
stack backtrace:
CPU: 1 PID: 609 Comm: kworker/u4:3 Not tainted 5.15.71 #1
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace
show_stack
dump_stack_lvl
dump_stack
print_circular_bug
check_noncircular
__lock_acquire
lock_acquire.part.0
lock_acquire
__mutex_lock
mutex_lock_nested
regmap_lock_mutex
regmap_read
lan9303_phy_read
dsa_slave_phy_read
__mdiobus_read
mdiobus_read
get_phy_device
mdiobus_scan
__mdiobus_register
dsa_register_switch
lan9303_probe
lan9303_mdio_probe
...
Cc: stable@vger.kernel.org Fixes: dc7005831523 ("net: dsa: LAN9303: add MDIO managed mode support") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20231027065741.534971-1-alexander.sverdlin@siemens.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel crash in AP bus code caused by very early invocation of the
config change callback function via SCLP.
After a fresh IML of the machine the crypto cards are still offline and
will get switched online only with activation of any LPAR which has the
card in it's configuration. A crypto card coming online is reported
to the LPAR via SCLP and the AP bus offers a callback function to get
this kind of information. However, it may happen that the callback is
invoked before the AP bus init function is complete. As the callback
triggers a synchronous AP bus scan, the scan may already run but some
internal states are not initialized by the AP bus init function resulting
in a crash like this:
This patch improves the ap_bus_force_rescan() function which is
invoked by the config change callback by checking if a first
initial AP bus scan has been done. If not, the force rescan request
is simple ignored. Anyhow it does not make sense to trigger AP bus
re-scans even before the very first bus scan is complete.
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com> Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com> Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abd3ac7902fb ("watchdog: sbsa: Support architecture version 1")
introduced new timer math for watchdog revision 1 with the 48 bit offset
register.
The gwdt->clk and timeout are u32, but the argument being calculated is
u64. Without a cast, the compiler performs u32 operations, truncating
intermediate steps, resulting in incorrect values.
A watchdog revision 1 implementation with a gwdt->clk of 1GHz and a
timeout of 600s writes 3647256576 to the one shot watchdog instead of 300000000000, resulting in the watchdog firing in 3.6s instead of 600s.
Force u64 math by casting the first argument (gwdt->clk) as a u64. Make
the order of operations explicit with parenthesis.
-EOPNOTSUPP is the return value that implements a "no-op" hook, not 0.
Without this fix having only the BPF LSM enabled (with no programs
attached) can cause uninitialized variable reads in
nfsd4_encode_fattr(), because the BPF hook returns 0 without touching
the 'ctxlen' variable and the corresponding 'contextlen' variable in
nfsd4_encode_fattr() remains uninitialized, yet being treated as valid
based on the 0 return value.
Cc: stable@vger.kernel.org Fixes: 98e828a0650f ("security: Refactor declaration of LSM hooks") Reported-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intent for the commit was to be able to detect carrier loss/gain
for just the NIC connected to the BMC. The unwanted effect is a
carrier loss for auxiliary paths also causes the BMC to lose
carrier. The BMC never regains carrier despite the secondary NIC
regaining a link.
This change, when merged, needs to be backported to stable kernels.
5.4-stable, 5.10-stable, 5.15-stable, 6.1-stable, 6.5-stable
Fixes: 3780bb29311e ("ncsi: Propagate carrier gain/loss events to the NCSI controller") CC: stable@vger.kernel.org Signed-off-by: Johnathan Mantey <johnathanx.mantey@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TCSR mutex bindings allow device to be described only with address
space (so it uses MMIO, not syscon regmap). This seems reasonable as
TCSR mutex is actually a dedicated IO address space and it also fixes DT
schema checks:
qcom/ipq6018-cp01-c1.dtb: hwlock: 'reg' is a required property
qcom/ipq6018-cp01-c1.dtb: hwlock: 'syscon' does not match any of the regexes: 'pinctrl-[0-9]+'
projects / thirdparty / kernel / stable.git / log
