Lock jsk->sk to prevent UAF when setsockopt(..., SO_J1939_FILTER, ...)
modifies jsk->filters while receiving packets.
Following trace was seen on affected system:
==================================================================
BUG: KASAN: slab-use-after-free in j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939]
Read of size 4 at addr ffff888012144014 by task j1939/350
In fs/ceph/caps.c, in encode_cap_msg(), "use after free" error was
caught by KASAN at this line - 'ceph_buffer_get(arg->xattr_buf);'. This
implies before the refcount could be increment here, it was freed.
In same file, in "handle_cap_grant()" refcount is decremented by this
line - 'ceph_buffer_put(ci->i_xattrs.blob);'. It appears that a race
occurred and resource was freed by the latter line before the former
line could increment it.
encode_cap_msg() is called by __send_cap() and __send_cap() is called by
ceph_check_caps() after calling __prep_cap(). __prep_cap() is where
arg->xattr_buf is assigned to ci->i_xattrs.blob. This is the spot where
the refcount must be increased to prevent "use after free" error.
Cc: stable@vger.kernel.org Link: https://tracker.ceph.com/issues/59259 Signed-off-by: Rishabh Dave <ridave@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Cc: stable@vger.kernel.org Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When updating the affinity of a VPE, the VMOVP command is currently skipped
if the two CPUs are part of the same VPE affinity.
But this is wrong, as the doorbell corresponding to this VPE is still
delivered on the 'old' CPU, which screws up the balancing. Furthermore,
offlining that 'old' CPU results in doorbell interrupts generated for this
VPE being discarded.
The harsh reality is that VMOVP cannot be elided when a set_affinity()
request occurs. It needs to be obeyed, and if an optimisation is to be
made, it is at the point where the affinity change request is made (such as
in KVM).
Drop the VMOVP elision altogether, and only use the vpe_table_mask
to try and stay within the same ITS affinity group if at all possible.
Fixes: dd3f050a216e (irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP) Reported-by: Kunkun Jiang <jiangkunkun@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240213101206.2137483-4-maz@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e92766e ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller") Signed-off-by: Doug Berger <opendmb@gmail.com> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Acked-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pointer can change here since the SKB can change, so we
actually later open-coded IEEE80211_SKB_CB() again. Reload
the pointer where needed, so the monitor-mode case using it
gets fixed, and then use info-> later as well.
When physical ports are reset (either through link failure or manually
toggled down and up again) that are slaved to a Linux bond with a tunnel
endpoint IP address on the bond device, not all tunnel packets arriving
on the bond port are decapped as expected.
The bond dev assigns the same MAC address to itself and each of its
slaves. When toggling a slave device, the same MAC address is therefore
offloaded to the NFP multiple times with different indexes.
The issue only occurs when re-adding the shared mac. The
nfp_tunnel_add_shared_mac() function has a conditional check early on
that checks if a mac entry already exists and if that mac entry is
global: (entry && nfp_tunnel_is_mac_idx_global(entry->index)). In the
case of a bonded device (For example br-ex), the mac index is obtained,
and no new index is assigned.
We therefore modify the conditional in nfp_tunnel_add_shared_mac() to
check if the port belongs to the LAG along with the existing checks to
prevent a new global mac index from being re-assigned to the slave port.
Fixes: 20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs") CC: stable@vger.kernel.org # 5.1+ Signed-off-by: Daniel de Villiers <daniel.devilliers@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 1st and 2nd expansion BAR configuration registers are configured,
when the driver starts up, in variables 'barcfg_msix_general' and
'barcfg_msix_xpb', respectively. The 'LengthSelect' field is ORed in
from bit 0, which is incorrect. The 'LengthSelect' field should
start from bit 27.
This has largely gone un-noticed because
NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT happens to be 0.
Fixes: 4cb584e0ee7d ("nfp: add CPP access core") Cc: stable@vger.kernel.org # 4.11+ Signed-off-by: Daniel Basilio <daniel.basilio@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1b05ece0c931 ("crypto: ccp - During shutdown, check SEV data pointer before using") Cc: stable@vger.kernel.org Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Kim Phillips <kim.phillips@amd.com> Reviewed-by: Liam Merwick <liam.merwick@oracle.com> Acked-by: John Allen <john.allen@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported a hang issue in migrate_pages_batch() called by mbind()
and nilfs_lookup_dirty_data_buffers() called in the log writer of nilfs2.
While migrate_pages_batch() locks a folio and waits for the writeback to
complete, the log writer thread that should bring the writeback to
completion picks up the folio being written back in
nilfs_lookup_dirty_data_buffers() that it calls for subsequent log
creation and was trying to lock the folio. Thus causing a deadlock.
In the first place, it is unexpected that folios/pages in the middle of
writeback will be updated and become dirty. Nilfs2 adds a checksum to
verify the validity of the log being written and uses it for recovery at
mount, so data changes during writeback are suppressed. Since this is
broken, an unclean shutdown could potentially cause recovery to fail.
Investigation revealed that the root cause is that the wait for writeback
completion in nilfs_page_mkwrite() is conditional, and if the backing
device does not require stable writes, data may be modified without
waiting.
Fix these issues by making nilfs_page_mkwrite() wait for writeback to
finish regardless of the stable write requirement of the backing device.
Link: https://lkml.kernel.org/r/20240131145657.4209-1-konishi.ryusuke@gmail.com Fixes: 1d1d1a767206 ("mm: only enforce stable page writes if the backing device requires it") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+ee2ae68da3b22d04cd8d@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/00000000000047d819061004ad6c@google.com Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper function nilfs_recovery_copy_block() of
nilfs_recovery_dsync_blocks(), which recovers data from logs created by
data sync writes during a mount after an unclean shutdown, incorrectly
calculates the on-page offset when copying repair data to the file's page
cache. In environments where the block size is smaller than the page
size, this flaw can cause data corruption and leak uninitialized memory
bytes during the recovery process.
Fix these issues by correcting this byte offset calculation on the page.
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO read-only state. This allows users with GPIOs that
never sleepbeing called in atomic context.
Implement the same mechanism as in commit 52af318c93e97 ("mmc: Allow
non-sleeping GPIO cd").
When ident_pud_init() uses only gbpages to create identity maps, large
ranges of addresses not actually requested can be included in the
resulting table; a 4K request will map a full GB. On UV systems, this
ends up including regions that will cause hardware to halt the system
if accessed (these are marked "reserved" by BIOS). Even processor
speculation into these regions is enough to trigger the system halt.
Only use gbpages when map creation requests include the full GB page
of space. Fall back to using smaller 2M pages when only portions of a
GB page are included in the request.
No attempt is made to coalesce mapping requests. If a request requires
a map entry at the 2M (pmd) level, subsequent mapping requests within
the same 1G region will also be at the pmd level, even if adjacent or
overlapping such requests could have been combined to map a full
gbpage. Existing usage starts with larger regions and then adds
smaller regions, so this should not have any great consequence.
[ dhansen: fix up comment formatting, simplifty changelog ]
The kernel built with MCRUSOE is unbootable on Transmeta Crusoe. It shows
the following error message:
This kernel requires an i686 CPU, but only detected an i586 CPU.
Unable to boot - please use a kernel appropriate for your CPU.
Remove MCRUSOE from the condition introduced in commit in Fixes, effectively
changing X86_MINIMUM_CPU_FAMILY back to 5 on that machine, which matches the
CPU family given by CPUID.
[ bp: Massage commit message. ]
Fixes: 25d76ac88821 ("x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig") Signed-off-by: Aleksander Mazur <deweloper@wp.pl> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20240123134309.1117782-1-deweloper@wp.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
The return type for ring_buffer_poll_wait() is __poll_t. This is behind
the scenes an unsigned where we can set event bits. In case of a
non-allocated CPU, we do return instead -EINVAL (0xffffffea). Lucky us,
this ends up setting few error bits (EPOLLERR | EPOLLHUP | EPOLLNVAL), so
user-space at least is aware something went wrong.
Nonetheless, this is an incorrect code. Replace that -EINVAL with a
proper EPOLLERR to clean that output. As this doesn't change the
behaviour, there's no need to treat this change as a bug fix.
Link: https://lore.kernel.org/linux-trace-kernel/20240131140955.3322792-1-vdonnefort@google.com Cc: stable@vger.kernel.org Fixes: 6721cb6002262 ("ring-buffer: Do not poll non allocated cpu buffers") Signed-off-by: Vincent Donnefort <vdonnefort@google.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the
VMBus channel"), napi_disable was getting called for all channels,
including all subchannels without confirming if they are enabled or not.
This caused hv_netvsc getting hung at napi_disable, when netvsc_probe()
has finished running but nvdev->subchan_work has not started yet.
netvsc_subchan_work() -> rndis_set_subchannel() has not created the
sub-channels and because of that netvsc_sc_open() is not running.
netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which
netvsc_subchan_work did not run.
netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI
cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the
NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the
opposite.
Now during netvsc_device_remove(), when napi_disable is called for those
subchannels, napi_disable gets stuck on infinite msleep.
This fix addresses this problem by ensuring that napi_disable() is not
getting called for non-enabled NAPI struct.
But netif_napi_del() is still necessary for these non-enabled NAPI struct
for cleanup purpose.
The kernel fails when compiling without `CONFIG_REGMAP_I2C` but with
`CONFIG_BMA400`.
```
ld: drivers/iio/accel/bma400_i2c.o: in function `bma400_i2c_probe':
bma400_i2c.c:(.text+0x23): undefined reference to `__devm_regmap_init_i2c'
```
Recently, we encounter kernel crash in function rm3100_common_probe
caused by out of bound access of array rm3100_samp_rates (because of
underlying hardware failures). Add boundary check to prevent out of
bound access.
Fixes: 121354b2eceb ("iio: magnetometer: Add driver support for PNI RM3100") Suggested-by: Zhouyi Zhou <zhouzhouyi@gmail.com> Signed-off-by: zhili.liu <zhili.liu@ucas.com.cn> Link: https://lore.kernel.org/r/1704157631-3814-1-git-send-email-zhouzhouyi@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4c3577db3e4f ("Staging: iio: impedance-analyzer: Fix sparse
warning") fixed a compiler warning, but introduced a bug that resulted
in one of the two 16 bit IIO channels always being zero (when both are
enabled).
This is because int is 32 bits wide on most architectures and in the
case of a little-endian machine the two most significant bytes would
occupy the buffer for the second channel as 'val' is being passed as a
void pointer to 'iio_push_to_buffers()'.
Fix by defining 'val' as u16. Tested working on ARM64.
While looking at improving the saved_cmdlines cache I found a huge amount
of wasted memory that should be used for the cmdlines.
The tracing data saves pids during the trace. At sched switch, if a trace
occurred, it will save the comm of the task that did the trace. This is
saved in a "cache" that maps pids to comms and exposed to user space via
the /sys/kernel/tracing/saved_cmdlines file. Currently it only caches by
default 128 comms.
The structure that uses this creates an array to store the pids using
PID_MAX_DEFAULT (which is usually set to 32768). This causes the structure
to be of the size of 131104 bytes on 64 bit machines.
In hex: 131104 = 0x20020, and since the kernel allocates generic memory in
powers of two, the kernel would allocate 0x40000 or 262144 bytes to store
this structure. That leaves 131040 bytes of wasted space.
Worse, the structure points to an allocated array to store the comm names,
which is 16 bytes times the amount of names to save (currently 128), which
is 2048 bytes. Instead of allocating a separate array, make the structure
end with a variable length string and use the extra space for that.
This is similar to a recommendation that Linus had made about eventfs_inode names:
Instead of allocating a separate string array to hold the saved comms,
have the structure end with: char saved_cmdlines[]; and round up to the
next power of two over sizeof(struct saved_cmdline_buffers) + num_cmdlines * TASK_COMM_LEN
It will use this extra space for the saved_cmdline portion.
Now, instead of saving only 128 comms by default, by using this wasted
space at the end of the structure it can save over 8000 comms and even
saves space by removing the need for allocating the other array.
Link: https://lore.kernel.org/linux-trace-kernel/20240209063622.1f7b6d5f@rorschach.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Vincent Donnefort <vdonnefort@google.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Mete Durlu <meted@linux.ibm.com> Fixes: 939c7a4f04fcd ("tracing: Introduce saved_cmdlines_size file") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ext4_move_extents(), moved_len is only updated when all moves are
successfully executed, and only discards orig_inode and donor_inode
preallocations when moved_len is not zero. When the loop fails to exit
after successfully moving some extents, moved_len is not updated and
remains at 0, so it does not discard the preallocations.
If the moved extents overlap with the preallocated extents, the
overlapped extents are freed twice in ext4_mb_release_inode_pa() and
ext4_process_freed_data() (as described in commit 94d7c16cbbbd ("ext4:
Fix double-free of blocks with EXT4_IOC_MOVE_EXT")), and bb_free is
incremented twice. Hence when trim is executed, a zero-division bug is
triggered in mb_update_avg_fragment_size() because bb_free is not zero
and bb_fragments is zero.
Therefore, update move_len after each extent move to avoid the issue.
Reported-by: Wei Chen <harperchen1110@gmail.com> Reported-by: xingwei lee <xrivendell7@gmail.com> Closes: https://lore.kernel.org/r/CAO4mrferzqBUnCag8R3m2zf897ts9UEuhjFQGPtODT92rYyR2Q@mail.gmail.com Fixes: fcf6b1b729bc ("ext4: refactor ext4_move_extents code base") CC: <stable@vger.kernel.org> # 3.18 Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20240104142040.2835097-2-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In remoteproc shutdown sequence, rpmsg_remove will get called which
would depopulate all the child nodes that have been created during
rpmsg_probe. This would result in cb_remove call for all the context
banks for the remoteproc. In cb_remove function, session 0 is
getting skipped which is not correct as session 0 will never become
available again. Add changes to mark session 0 also as invalid.
In (e)poll mode, threads often depend on I/O events to determine when
data is ready for consumption. Within binder, a thread may initiate a
command via BINDER_WRITE_READ without a read buffer and then make use
of epoll_wait() or similar to consume any responses afterwards.
It is then crucial that epoll threads are signaled via wakeup when they
queue their own work. Otherwise, they risk waiting indefinitely for an
event leaving their work unhandled. What is worse, subsequent commands
won't trigger a wakeup either as the thread has pending work.
Invoking the make_tx_response() / push_tx_responses() pair with no lock
held would be acceptable only if all such invocations happened from the
same context (NAPI instance or dealloc thread). Since this isn't the
case, and since the interface "spec" also doesn't demand that multicast
operations may only be performed with no in-flight transmits,
MCAST_{ADD,DEL} processing also needs to acquire the response lock
around the invocations.
To prevent similar mistakes going forward, "downgrade" the present
functions to private helpers of just the two remaining ones using them
directly, with no forward declarations anymore. This involves renaming
what so far was make_tx_response(), for the new function of that name
to serve the new (wrapper) purpose.
While there,
- constify the txp parameters,
- correct xenvif_idx_release()'s status parameter's type,
- rename {,_}make_tx_response()'s status parameters for consistency with
xenvif_idx_release()'s.
Fixes: 210c34dcd8d9 ("xen-netback: add support for multicast control") Cc: stable@vger.kernel.org Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Link: https://lore.kernel.org/r/980c6c3d-e10e-4459-8565-e8fbde122f00@suse.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller reported [1] hitting a warning after failing to allocate
resources for skb in hsr_init_skb(). Since a WARN_ONCE() call will
not help much in this case, it might be prudent to switch to
netdev_warn_once(). At the very least it will suppress syzkaller
reports such as [1].
Just in case, use netdev_warn_once() in send_prp_supervision_frame()
for similar reasons.
rx_data_reassembly skb is stored during NCI data exchange for processing
fragmented packets. It is dropped only when the last fragment is processed
or when an NTF packet with NCI_OP_RF_DEACTIVATE_NTF opcode is received.
However, the NCI device may be deallocated before that which leads to skb
leak.
As by design the rx_data_reassembly skb is bound to the NCI device and
nothing prevents the device to be freed before the skb is processed in
some way and cleaned, free it on the NCI device cleanup.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 6a2968aaf50c ("NFC: basic NCI protocol implementation") Cc: stable@vger.kernel.org Reported-by: syzbot+6b7c68d9c21e4ee4251b@syzkaller.appspotmail.com Closes: https://lore.kernel.org/lkml/000000000000f43987060043da7b@google.com/ Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 90ceddcb4950 ("bpf: Support llvm-objcopy for vmlinux BTF")
changed the ELF type of .btf.vmlinux.bin.o to ET_REL via dd, which works
fine for little endian platforms:
While in the area, update the comment to mention that binutils 2.35+
matches LLD's behavior of rejecting an ET_EXEC input, which occurred
after the comment was added.
Cc: stable@vger.kernel.org Fixes: 90ceddcb4950 ("bpf: Support llvm-objcopy for vmlinux BTF") Link: https://github.com/llvm/llvm-project/pull/75643 Suggested-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Fangrui Song <maskray@google.com> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Justin Stitt <justinstitt@google.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[nathan: Fix silent conflict due to lack of 7d153696e5db in older trees] Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inode_getsecctx LSM hook has previously been corrected to have
-EOPNOTSUPP instead of 0 as the default return value to fix BPF LSM
behavior. However, the call_int_hook()-generated loop in
security_inode_getsecctx() was left treating 0 as the neutral value, so
after an LSM returns 0, the loop continues to try other LSMs, and if one
of them returns a non-zero value, the function immediately returns with
said value. So in a situation where SELinux and the BPF LSMs registered
this hook, -EOPNOTSUPP would be incorrectly returned whenever SELinux
returned 0.
Fix this by open-coding the call_int_hook() loop and making it use the
correct LSM_RET_DEFAULT() value as the neutral one, similar to what
other hooks do.
get_line() does not trim the leading spaces, but the
parse_source_files() expects to get lines with source files paths where
the first space occurs after the file path.
Fixes: 70f30cfe5b89 ("modpost: use read_text_file() and get_line() for reading text files") Signed-off-by: Radek Krejci <radek.krejci@oracle.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the Intel datasheets, software must reset the block
buffer index twice for block process call transactions: once before
writing the outgoing data to the buffer, and once again before
reading the incoming data from the buffer.
The driver is currently missing the second reset, causing the wrong
portion of the block buffer to be read.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Reported-by: Piotr Zakowski <piotr.zakowski@intel.com> Closes: https://lore.kernel.org/linux-i2c/20240213120553.7b0ab120@endymion.delvare/ Fixes: 315cd67c9453 ("i2c: i801: Add Block Write-Block Read Process Call support") Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If FEATURE_BLOCK_BUFFER is set then bit SMBAUXCTL_E32B is supported
and there's no benefit in reading it back. Origin of this check
seems to be 14 yrs ago when people were not completely sure which
chip versions support the block buffer mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Tested-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: c1c9d0f6f7f1 ("i2c: i801: Fix block process call transactions") Signed-off-by: Sasha Levin <sashal@kernel.org>
In kasan_init_region, when k_start is not page aligned, at the begin of
for loop, k_cur = k_start & PAGE_MASK is less than k_start, and then
`va = block + k_cur - k_start` is less than block, the addr va is invalid,
because the memory address space from va to block is not alloced by
memblock_alloc, which will not be reserved by memblock_reserve later, it
will be used by other places.
As a result, memory overwriting occurs.
for example:
int __init __weak kasan_init_region(void *start, size_t size)
{
[...]
/* if say block(dcd97000) k_start(feef7400) k_end(feeff3fe) */
block = memblock_alloc(k_end - k_start, PAGE_SIZE);
[...]
for (k_cur = k_start & PAGE_MASK; k_cur < k_end; k_cur += PAGE_SIZE) {
/* at the begin of for loop
* block(dcd97000) va(dcd96c00) k_cur(feef7000) k_start(feef7400)
* va(dcd96c00) is less than block(dcd97000), va is invalid
*/
void *va = block + k_cur - k_start;
[...]
}
[...]
}
Therefore, page alignment is performed on k_start before
memblock_alloc() to ensure the validity of the VA address.
Fixes: 663c0c9496a6 ("powerpc/kasan: Fix shadow area set up for modules.") Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/1705974359-43790-1-git-send-email-xiaojiangfeng@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@kernel.org> Fixes: 7d2d641c44269 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device") Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8ec ("usb: typec: ucsi: acpi: Move to the new API") Cc: stable@vger.kernel.org Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a input device is opened before hid_hw_start is called, events may
not be received from the hardware. In the case of USB-backed devices,
for example, the hid_hw_start function is responsible for filling in
the URB which is submitted when the input device is opened. If a device
is opened prematurely, polling will never start because the device will
not have been in the correct state to send the URB.
Because the wacom driver registers its input devices before calling
hid_hw_start, there is a window of time where a device can be opened
and end up in an inoperable state. Some ARM-based Chromebooks in particular
reliably trigger this bug.
This commit splits the wacom_register_inputs function into two pieces.
One which is responsible for setting up the allocated inputs (and runs
prior to hid_hw_start so that devices are ready for any input events
they may end up receiving) and another which only registers the devices
(and runs after hid_hw_start to ensure devices can be immediately opened
without issue). Note that the functions to initialize the LEDs and remotes
are also moved after hid_hw_start to maintain their own dependency chains.
The xf86-input-wacom driver does not treat '0' as a valid serial
number and will drop any input report which contains an
MSC_SERIAL = 0 event. The kernel driver already takes care to
avoid sending any MSC_SERIAL event if the value of serial[0] == 0
(which is the case for devices that don't actually report a
serial number), but this is not quite sufficient.
Only the lower 32 bits of the serial get reported to userspace,
so if this portion of the serial is zero then there can still
be problems.
This commit allows the driver to report either the lower 32 bits
if they are non-zero or the upper 32 bits otherwise.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com> Fixes: f85c9dc678a5 ("HID: wacom: generic: Support tool ID and additional tool types") CC: stable@vger.kernel.org # v4.10 Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you connect an external headset/microphone to the 3.5mm jack on the
Acer Swift 1 SF114-32 it does not recognize the microphone. This fixes
that and gives the user the ability to choose between internal and
headset mic.
(struct dirty_throttle_control *)->thresh is an unsigned long, but is
passed as the u32 divisor argument to div_u64(). On architectures where
unsigned long is 64 bytes, the argument will be implicitly truncated.
Use div64_u64() instead of div_u64() so that the value used in the "is
this a safe division" check is the same as the divisor.
Also, remove redundant cast of the numerator to u64, as that should happen
implicitly.
This would be difficult to exploit in memcg domain, given the ratio-based
arithmetic domain_drity_limits() uses, but is much easier in global
writeback domain with a BDI_CAP_STRICTLIMIT-backing device, using e.g.
vm.dirty_bytes=(1<<32)*PAGE_SIZE so that dtc->thresh == (1<<32)
Link: https://lkml.kernel.org/r/20240118181954.1415197-1-zokeefe@google.com Fixes: f6789593d5ce ("mm/page-writeback.c: fix divide by zero in bdi_dirty_limits()") Signed-off-by: Zach O'Keefe <zokeefe@google.com> Cc: Maxim Patlasov <MPatlasov@parallels.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix register_snapshot_trigger() to return error code if it failed to
allocate a snapshot instead of 0 (success). Unless that, it will register
snapshot trigger without an error.
Link: https://lore.kernel.org/linux-trace-kernel/170622977792.270660.2789298642759362200.stgit@devnote2 Fixes: 0bbe7f719985 ("tracing: Fix the race between registering 'snapshot' event trigger and triggering 'snapshot' operation") Cc: stable@vger.kernel.org Cc: Vincent Donnefort <vdonnefort@google.com> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39fac ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After 'lib: checksum: Use aligned accesses for ip_fast_csum and
csum_ipv6_magic tests' was applied, the test_csum_ipv6_magic unit test
started failing for all mips platforms, both little and bit endian.
Oddly enough, adding debug code into test_csum_ipv6_magic() made the
problem disappear.
The gcc manual says:
"The "memory" clobber tells the compiler that the assembly code performs
memory reads or writes to items other than those listed in the input
and output operands (for example, accessing the memory pointed to by one
of the input parameters)
"
This is definitely the case for csum_ipv6_magic(). Indeed, adding the
'memory' clobber fixes the problem.
Cc: Charlie Jenkins <charlie@rivosinc.com> Cc: Palmer Dabbelt <palmer@rivosinc.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Charlie Jenkins <charlie@rivosinc.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Documentation/ABI/testing/sysfs-class-net-statistics documentation
is pointing to the wrong path for the interface. Documentation is
pointing to /sys/class/<iface>, instead of /sys/class/net/<iface>.
Fix it by adding the `net/` directory before the interface.
Fixes: 6044f9700645 ("net: sysfs: document /sys/class/net/statistics/*") Signed-off-by: Breno Leitao <leitao@debian.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a path in rt5645_jack_detect_work(), where rt5645->jd_mutex
is left locked forever. That may lead to deadlock
when rt5645_jack_detect_work() is called for the second time.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Since commit 24778be20f87 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.
The ovs module allows for some actions to recursively contain an action
list for complex scenarios, such as sampling, checking lengths, etc.
When these actions are copied into the internal flow table, they are
evaluated to validate that such actions make sense, and these calls
happen recursively.
The ovs-vswitchd userspace won't emit more than 16 recursion levels
deep. However, the module has no such limit and will happily accept
limits larger than 16 levels nested. Prevent this by tracking the
number of recursions happening and manually limiting it to 16 levels
nested.
The initial implementation of the sample action would track this depth
and prevent more than 3 levels of recursion, but this was removed to
support the clone use case, rather than limited at the current userspace
limit.
Fixes: 798c166173ff ("openvswitch: Optimize sample action for the clone use cases") Signed-off-by: Aaron Conole <aconole@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240207132416.1488485-2-aconole@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When some ioctl flags are checked we return EOPNOTSUPP, like for
BTRFS_SCRUB_SUPPORTED_FLAGS, BTRFS_SUBVOL_CREATE_ARGS_MASK or fallocate
modes. The EINVAL is supposed to be for a supported but invalid
values or combination of options. Fix that when checking send flags so
it's consistent with the rest.
If a subvolume still exists, forbid deleting its qgroup 0/subvolid.
This behavior generally leads to incorrect behavior in squotas and
doesn't have a legitimate purpose.
Fixes: cecbb533b5fc ("btrfs: record simple quota deltas in delayed refs") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
There is a syzbot crash, triggered by the ASSERT() during subvolume
creation:
assertion failed: !anon_dev, in fs/btrfs/disk-io.c:1319
------------[ cut here ]------------
kernel BUG at fs/btrfs/disk-io.c:1319!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:btrfs_get_root_ref.part.0+0x9aa/0xa60
<TASK>
btrfs_get_new_fs_root+0xd3/0xf0
create_subvol+0xd02/0x1650
btrfs_mksubvol+0xe95/0x12b0
__btrfs_ioctl_snap_create+0x2f9/0x4f0
btrfs_ioctl_snap_create+0x16b/0x200
btrfs_ioctl+0x35f0/0x5cf0
__x64_sys_ioctl+0x19d/0x210
do_syscall_64+0x3f/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b
---[ end trace 0000000000000000 ]---
[CAUSE]
During create_subvol(), after inserting root item for the newly created
subvolume, we would trigger btrfs_get_new_fs_root() to get the
btrfs_root of that subvolume.
The idea here is, we have preallocated an anonymous device number for
the subvolume, thus we can assign it to the new subvolume.
But there is really nothing preventing things like backref walk to read
the new subvolume.
If that happens before we call btrfs_get_new_fs_root(), the subvolume
would be read out, with a new anonymous device number assigned already.
In that case, we would trigger ASSERT(), as we really expect no one to
read out that subvolume (which is not yet accessible from the fs).
But things like backref walk is still possible to trigger the read on
the subvolume.
Thus our assumption on the ASSERT() is not correct in the first place.
[FIX]
Fix it by removing the ASSERT(), and just free the @anon_dev, reset it
to 0, and continue.
If the subvolume tree is read out by something else, it should have
already get a new anon_dev assigned thus we only need to free the
preallocated one.
Reported-by: Chenyuan Yang <chenyuan0y@gmail.com> Fixes: 2dfb1e43f57d ("btrfs: preallocate anon block device at first phase of snapshot creation") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creating a qgroup 0/subvolid leads to various races and it isn't
helpful, because you can't specify a subvol id when creating a subvol,
so you can't be sure it will be the right one. Any requirements on the
automatic subvol can be gratified by using a higher level qgroup and the
inheritance parameters of subvol creation.
Fixes: cecbb533b5fc ("btrfs: record simple quota deltas in delayed refs") CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rbtree lazy gc on insert might collect an end interval element that has
been just added in this transactions, skip end interval elements that
are not yet active.
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels") Reported-by: Jon Hunter <jonathanh@nvidia.com> Closes: https://lore.kernel.org/netdev/c25eb595-8d91-40ea-9f52-efa15ebafdbc@nvidia.com/ Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402081135.lAxxBXHk-lkp@intel.com/ Signed-off-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been reports of the watchdog marking clocksources unstable on
machines with 8 NUMA nodes:
clocksource: timekeeping watchdog on CPU373:
Marking clocksource 'tsc' as unstable because the skew is too large:
clocksource: 'hpet' wd_nsec: 14523447520
clocksource: 'tsc' cs_nsec: 14524115132
The measured clocksource skew - the absolute difference between cs_nsec
and wd_nsec - was 668 microseconds:
The kernel used 200 microseconds for the uncertainty_margin of both the
clocksource and watchdog, resulting in a threshold of 400 microseconds (the
md variable). Both the cs_nsec and the wd_nsec value indicate that the
readout interval was circa 14.5 seconds. The observed behaviour is that
watchdog checks failed for large readout intervals on 8 NUMA node
machines. This indicates that the size of the skew was directly proportinal
to the length of the readout interval on those machines. The measured
clocksource skew, 668 microseconds, was evaluated against a threshold (the
md variable) that is suited for readout intervals of roughly
WATCHDOG_INTERVAL, i.e. HZ >> 1, which is 0.5 second.
The intention of 2e27e793e280 ("clocksource: Reduce clocksource-skew
threshold") was to tighten the threshold for evaluating skew and set the
lower bound for the uncertainty_margin of clocksources to twice
WATCHDOG_MAX_SKEW. Later in c37e85c135ce ("clocksource: Loosen clocksource
watchdog constraints"), the WATCHDOG_MAX_SKEW constant was increased to
125 microseconds to fit the limit of NTP, which is able to use a
clocksource that suffers from up to 500 microseconds of skew per second.
Both the TSC and the HPET use default uncertainty_margin. When the
readout interval gets stretched the default uncertainty_margin is no
longer a suitable lower bound for evaluating skew - it imposes a limit
that is far stricter than the skew with which NTP can deal.
The root causes of the skew being directly proportinal to the length of
the readout interval are:
* the inaccuracy of the shift/mult pairs of clocksources and the watchdog
* the conversion to nanoseconds is imprecise for large readout intervals
Prevent this by skipping the current watchdog check if the readout
interval exceeds 2 * WATCHDOG_INTERVAL. Considering the maximum readout
interval of 2 * WATCHDOG_INTERVAL, the current default uncertainty margin
(of the TSC and HPET) corresponds to a limit on clocksource skew of 250
ppm (microseconds of skew per second). To keep the limit imposed by NTP
(500 microseconds of skew per second) for all possible readout intervals,
the margins would have to be scaled so that the threshold value is
proportional to the length of the actual readout interval.
As for why the readout interval may get stretched: Since the watchdog is
executed in softirq context the expiration of the watchdog timer can get
severely delayed on account of a ksoftirqd thread not getting to run in a
timely manner. Surely, a system with such belated softirq execution is not
working well and the scheduling issue should be looked into but the
clocksource watchdog should be able to deal with it accordingly.
After commit 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in
translated mode") the keyboard on Dell XPS 13 9350 / 9360 / 9370 models
has stopped working after a suspend/resume.
The problem appears to be that atkbd_probe() fails when called
from atkbd_reconnect() on resume, which on systems where
ATKBD_CMD_GETID is skipped can only happen by ATKBD_CMD_SETLEDS
failing. ATKBD_CMD_SETLEDS failing because ATKBD_CMD_GETID was
skipped is weird, but apparently that is what is happening.
Fix this by also skipping ATKBD_CMD_SETLEDS when skipping
ATKBD_CMD_GETID.
Fixes: 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in translated mode") Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Closes: https://lore.kernel.org/linux-input/0aa4a61f-c939-46fe-a572-08022e8931c7@molgen.mpg.de/ Closes: https://bbs.archlinux.org/viewtopic.php?pid=2146300 Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218424 Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2260517 Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20240126160724.13278-2-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When closing the laptop lid with an external screen connected, the mouse
pointer has a constant movement to the lower right corner. Opening the
lid again stops this movement, but after that the touchpad does no longer
register clicks.
The touchpad is connected both via i2c-hid and PS/2, the predecessor of
this device (NS70MU) has the same layout in this regard and also strange
behaviour caused by the psmouse and the i2c-hid driver fighting over
touchpad control. This fix is reusing the same workaround by just
disabling the PS/2 aux port, that is only used by the touchpad, to give the
i2c-hid driver the lone control over the touchpad.
The hrtimers migration on CPU-down hotplug process has been moved
earlier, before the CPU actually goes to die. This leaves a small window
of opportunity to queue an hrtimer in a blind spot, leaving it ignored.
For example a practical case has been reported with RCU waking up a
SCHED_FIFO task right before the CPUHP_AP_IDLE_DEAD stage, queuing that
way a sched/rt timer to the local offline CPU.
Make sure such situations never go unnoticed and warn when that happens.
Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier") Reported-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240129235646.3171983-4-boqun.feng@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11 Fixes: bac1ec551434 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK") Signed-off-by: Prashanth K <quic_prashk@quicinc.com> Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device IMST USB-Stick for Smart Meter is a rebranded IMST iM871A-USB
Wireless M-Bus USB-adapter. It is used to read wireless water, gas and
electricity meters.
Signed-off-by: Leonard Dallmayr <leonard.dallmayr@mailbox.org> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the USB serial option driver support for the Fibocom
FM101-GL
LTE modules as there are actually several different variants.
- VID:PID 2cb7:01a3, FM101-GL are laptop M.2 cards (with
MBIM interfaces for /Linux/Chrome OS)
Use IS_ENABLED(CONFIG_IUCV) to determine whether the iucv_if symbol
is available, and let depmod deal with the module dependency.
This was introduced back with commit 6fcd61f7bf5d ("af_iucv: use
loadable iucv interface"). And to avoid sprinkling IS_ENABLED() over
all the code, we're keeping the indirection through pr_iucv->...().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When iocg_kick_delay() is called from a CPU different than the one which set
the delay, @now may be in the past of @iocg->delay_at leading to the
following warning:
UBSAN: shift-out-of-bounds in block/blk-iocost.c:1359:23
shift exponent 18446744073709 is too large for 64-bit type 'u64' (aka 'unsigned long long')
...
Call Trace:
<TASK>
dump_stack_lvl+0x79/0xc0
__ubsan_handle_shift_out_of_bounds+0x2ab/0x300
iocg_kick_delay+0x222/0x230
ioc_rqos_merge+0x1d7/0x2c0
__rq_qos_merge+0x2c/0x80
bio_attempt_back_merge+0x83/0x190
blk_attempt_plug_merge+0x101/0x150
blk_mq_submit_bio+0x2b1/0x720
submit_bio_noacct_nocheck+0x320/0x3e0
__swap_writepage+0x2ab/0x9d0
The underflow itself doesn't really affect the behavior in any meaningful
way; however, the past timestamp may exaggerate the delay amount calculated
later in the code, which shouldn't be a material problem given the nature of
the delay mechanism.
If @now is in the past, this CPU is racing another CPU which recently set up
the delay and there's nothing this CPU can contribute w.r.t. the delay.
Let's bail early from iocg_kick_delay() in such cases.
Commit 4373534a9850 ("scsi: core: Move scsi_host_busy() out of host lock
for waking up EH handler") intended to fix a hard lockup issue triggered by
EH. The core idea was to move scsi_host_busy() out of the host lock when
processing individual commands for EH. However, a suggested style change
inadvertently caused scsi_host_busy() to remain under the host lock. Fix
this by calling scsi_host_busy() outside the lock.
Fixes: 4373534a9850 ("scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler") Cc: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20240203024521.2006455-1-ming.lei@redhat.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Pipapo needs a scratchpad area to keep state during matching.
This state can be large and thus cannot reside on stack.
Each set preallocates percpu areas for this.
On each match stage, one scratchpad half starts with all-zero and the other
is inited to all-ones.
At the end of each stage, the half that starts with all-ones is
always zero. Before next field is tested, pointers to the two halves
are swapped, i.e. resmap pointer turns into fill pointer and vice versa.
After the last field has been processed, pipapo stashes the
index toggle in a percpu variable, with assumption that next packet
will start with the all-zero half and sets all bits in the other to 1.
This isn't reliable.
There can be multiple sets and we can't be sure that the upper
and lower half of all set scratch map is always in sync (lookups
can be conditional), so one set might have swapped, but other might
not have been queried.
Thus we need to keep the index per-set-and-cpu, just like the
scratchpad.
Note that this bug fix is incomplete, there is a related issue.
avx2 and normal implementation might use slightly different areas of the
map array space due to the avx2 alignment requirements, so
m->scratch (generic/fallback implementation) and ->scratch_aligned
(avx) may partially overlap. scratch and scratch_aligned are not distinct
objects, the latter is just the aligned address of the former.
After this change, write to scratch_align->map_index may write to
scratch->map, so this issue becomes more prominent, we can set to 1
a bit in the supposedly-all-zero area of scratch->map[].
A followup patch will remove the scratch_aligned and makes generic and
avx code use the same (aligned) area.
Its done in a separate change to ease review.
Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges") Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
xt_check_{match,target} expects u16, but NFTA_RULE_COMPAT_PROTO is u32.
NLA_POLICY_MAX(NLA_BE32, 65535) cannot be used because .max in
nla_policy is s16, see 3e48be05f3c7 ("netlink: add attribute range
validation to policy").
Fixes: 0ca743a55991 ("netfilter: nf_tables: add compatibility layer for x_tables") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cause of this issue is that when tipc_nl_bearer_add() is called with
the TIPC_NLA_BEARER_UDP_OPTS attribute, tipc_udp_nl_bearer_add() is called
even if the bearer is not UDP.
tipc_udp_is_known_peer() called by tipc_udp_nl_bearer_add() assumes that
the media_ptr field of the tipc_bearer has an udp_bearer type object, so
the function goes crazy for non-UDP bearers.
This patch fixes the issue by checking the bearer type before calling
tipc_udp_nl_bearer_add() in tipc_nl_bearer_add().
Stop rxrpc from sending a DUP ACK in response to a PING RESPONSE ACK on a
dead call. We may have initiated the ping but the call may have beaten the
response to completion.
Fixes: 18bfeba50dfd ("rxrpc: Perform terminal call ACK/ABORT retransmission from conn processor") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
inet_recv_error() is called without holding the socket lock.
IPv6 socket could mutate to IPv4 with IPV6_ADDRFORM
socket option and trigger a KCSAN warning.
Fixes: f4713a3dfad0 ("net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before commit 7108b80a542b ("hwmon/coretemp: Handle large core ID
value"), there is a fixed mapping between
1. cpu_core_id
2. the index in pdata->core_data[] array
3. the sysfs attr name, aka "tempX_"
The later two always equal cpu_core_id + 2.
After the commit, pdata->core_data[] index is got from ida so that it
can handle sparse core ids and support more cores within a package.
However, the commit erroneously maps the sysfs attr name to
pdata->core_data[] index instead of cpu_core_id + 2.
As a result, the code is not aligned with the comments, and brings user
visible changes in hwmon sysfs on systems with sparse core id.
For example, before commit 7108b80a542b ("hwmon/coretemp: Handle large
core ID value"),
/sys/class/hwmon/hwmon2/temp2_label:Core 0
/sys/class/hwmon/hwmon2/temp3_label:Core 1
/sys/class/hwmon/hwmon2/temp4_label:Core 2
/sys/class/hwmon/hwmon2/temp5_label:Core 3
/sys/class/hwmon/hwmon2/temp6_label:Core 4
/sys/class/hwmon/hwmon3/temp10_label:Core 8
/sys/class/hwmon/hwmon3/temp11_label:Core 9
after commit,
/sys/class/hwmon/hwmon2/temp2_label:Core 0
/sys/class/hwmon/hwmon2/temp3_label:Core 1
/sys/class/hwmon/hwmon2/temp4_label:Core 2
/sys/class/hwmon/hwmon2/temp5_label:Core 3
/sys/class/hwmon/hwmon2/temp6_label:Core 4
/sys/class/hwmon/hwmon2/temp7_label:Core 8
/sys/class/hwmon/hwmon2/temp8_label:Core 9
Restore the previous behavior and rework the code, comments and variable
names to avoid future confusions.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the ICMPv6 error is built from a non-linear skb we get the following
splat,
BUG: KASAN: slab-out-of-bounds in do_csum+0x220/0x240
Read of size 4 at addr ffff88811d402c80 by task netperf/820
CPU: 0 PID: 820 Comm: netperf Not tainted 6.8.0-rc1+ #543
...
kasan_report+0xd8/0x110
do_csum+0x220/0x240
csum_partial+0xc/0x20
skb_tunnel_check_pmtu+0xeb9/0x3280
vxlan_xmit_one+0x14c2/0x4080
vxlan_xmit+0xf61/0x5c00
dev_hard_start_xmit+0xfb/0x510
__dev_queue_xmit+0x7cd/0x32a0
br_dev_queue_push_xmit+0x39d/0x6a0
Use skb_checksum instead of csum_partial who cannot deal with non-linear
SKBs.
Fixes: 4cb47a8644cc ("tunnels: PMTU discovery support for directly bridged IP packets") Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using hard-coded constant timeout to wait for some expected
event is deemed to fail sooner or later, especially in slow
env.
Our CI has spotted another of such race:
# TEST: ipv6: cleanup of cached exceptions - nexthop objects [FAIL]
# can't delete veth device in a timely manner, PMTU dst likely leaked
Replace the crude sleep with a loop looking for the expected condition
at low interval for a much longer range.
Commit 56e58d6c8a56 ("net: stmmac: Implement Safety Features in
XGMAC core") checks and reports safety errors, but leaves the
Data Path Parity Errors for each channel in DMA unhandled at all, lead to
a storm of interrupt.
Fix it by checking and clearing the DMA_DPP_Interrupt_Status register.
Fixes: 56e58d6c8a56 ("net: stmmac: Implement Safety Features in XGMAC core") Signed-off-by: Furong Xu <0x1207@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
MSA MISC0 bit 1 to 7 contains Colorimetry Indicator Field.
dp_link_get_colorimetry_config() returns wrong colorimetry value
in the DP_TEST_DYNAMIC_RANGE_CEA case in the current implementation.
Hence fix this problem by having dp_link_get_colorimetry_config()
return defined CEA RGB colorimetry value in the case of
DP_TEST_DYNAMIC_RANGE_CEA.
Changes in V2:
-- drop retrieving colorimetry from colorspace
-- drop dr = link->dp_link.test_video.test_dyn_range assignment
Changes in V3:
-- move defined MISCr0a Colorimetry vale to dp_reg.h
-- rewording commit title
-- rewording commit text to more precise describe this patch
If the external phy working together with phy-omap-usb2 does not implement
send_srp(), we may still attempt to call it. This can happen on an idle
Ethernet gadget triggering a wakeup for example:
configfs-gadget.g1 gadget.0: ECM Suspend
configfs-gadget.g1 gadget.0: Port suspended. Triggering wakeup
...
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when execute
...
PC is at 0x0
LR is at musb_gadget_wakeup+0x1d4/0x254 [musb_hdrc]
...
musb_gadget_wakeup [musb_hdrc] from usb_gadget_wakeup+0x1c/0x3c [udc_core]
usb_gadget_wakeup [udc_core] from eth_start_xmit+0x3b0/0x3d4 [u_ether]
eth_start_xmit [u_ether] from dev_hard_start_xmit+0x94/0x24c
dev_hard_start_xmit from sch_direct_xmit+0x104/0x2e4
sch_direct_xmit from __dev_queue_xmit+0x334/0xd88
__dev_queue_xmit from arp_solicit+0xf0/0x268
arp_solicit from neigh_probe+0x54/0x7c
neigh_probe from __neigh_event_send+0x22c/0x47c
__neigh_event_send from neigh_resolve_output+0x14c/0x1c0
neigh_resolve_output from ip_finish_output2+0x1c8/0x628
ip_finish_output2 from ip_send_skb+0x40/0xd8
ip_send_skb from udp_send_skb+0x124/0x340
udp_send_skb from udp_sendmsg+0x780/0x984
udp_sendmsg from __sys_sendto+0xd8/0x158
__sys_sendto from ret_fast_syscall+0x0/0x58
Let's fix the issue by checking for send_srp() and set_vbus() before
calling them. For USB peripheral only cases these both could be NULL.
Fixes: 657b306a7bdf ("usb: phy: add a new driver for omap usb2 phy") Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20240128120556.8848-1-tony@atomide.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Propagate the TR response status to the device using BCDMA
split-channels. For example CSI-RX driver should be able to check if a
frame was not transferred completely (short packet) and needs to be
discarded.
Fixes: 25dcb5dd7b7c ("dmaengine: ti: New driver for K3 UDMA") Signed-off-by: Jai Luthra <j-luthra@ti.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com> Link: https://lore.kernel.org/r/20240103-tr_resp_err-v1-1-2fdf6d48ab92@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
