An issue occurred while reading an ELF file in libbpf.c during fuzzing:
Program received signal SIGSEGV, Segmentation fault.
0x0000000000958e97 in bpf_object.collect_prog_relos () at libbpf.c:4206
4206 in libbpf.c
(gdb) bt
#0 0x0000000000958e97 in bpf_object.collect_prog_relos () at libbpf.c:4206
#1 0x000000000094f9d6 in bpf_object.collect_relos () at libbpf.c:6706
#2 0x000000000092bef3 in bpf_object_open () at libbpf.c:7437
#3 0x000000000092c046 in bpf_object.open_mem () at libbpf.c:7497
#4 0x0000000000924afa in LLVMFuzzerTestOneInput () at fuzz/bpf-object-fuzzer.c:16
#5 0x000000000060be11 in testblitz_engine::fuzzer::Fuzzer::run_one ()
#6 0x000000000087ad92 in tracing::span::Span::in_scope ()
#7 0x00000000006078aa in testblitz_engine::fuzzer::util::walkdir ()
#8 0x00000000005f3217 in testblitz_engine::entrypoint::main::{{closure}} ()
#9 0x00000000005f2601 in main ()
(gdb)
scn_data was null at this code(tools/lib/bpf/src/libbpf.c):
if (rel->r_offset % BPF_INSN_SZ || rel->r_offset >= scn_data->d_size) {
The Wi-Fi firmware 29.29.X should use version 2 role info format. FDDT
mechanism version 5 use the same cell members to judge traffic situation,
don't need to add another new format.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20231218061341.51255-2-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a node is only one in port or one out port, address-cells and
size-cells are not required in in-ports and out-ports. And the number
and reg of the port need to be removed.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com> Link: https://lore.kernel.org/r/20231210072633.4243-5-quic_jinlmao@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Upon assembling the array, both kernel and mdadm allow the devices to have event
counter difference of 1, and still consider them as up-to-date.
However, a device whose event count is behind by 1, may in fact not be up-to-date,
and array resync with such a device may cause data corruption.
To avoid this, consult the superblock of the freshest device about the status
of a device, whose event counter is behind by 1.
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver has a logic leak in ring data allocation/free,
where aq_ring_free could be called multiple times on same ring,
if system is under stress and got memory allocation error.
Ring pointer was used as an indicator of failure, but this is
not correct since only ring data is allocated/deallocated.
Ring itself is an array member.
Changing ring allocation functions to return error code directly.
This simplifies error handling and eliminates aq_ring_free
on higher layer.
Fix the values of the ICE_AQ_VSI_Q_OPT_RSS_* registers. Shifting is
already done when the values are used, no need to double shift. Bug was
not discovered earlier since only ICE_AQ_VSI_Q_OPT_RSS_TPLZ (Zero) is
currently used.
Also, rename ICE_AQ_VSI_Q_OPT_RSS_XXX to ICE_AQ_VSI_Q_OPT_RSS_HASH_XXX
for consistency.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Link: https://lore.kernel.org/r/20231213003321.605376-5-ahmed.zaki@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently in directly attached scenario, the phyup event
HISI_PHYE_PHY_UP_PM is notified before .phy_attached is set - this may
cause the phyup work hisi_sas_bytes_dmaed() execution failed and the
attached device will not be found.
To fix it, set .phy_attached before notifing phyup event.
If priority tagging is set in the service parameters of a FLOGI cmpl, then
we update the vmid_flag. In the current logic, if a follow up FLOGI cmpl
updates its service parameters such that priority tagging is no longer set,
then the vmid_flag ends up keeping stale data.
Fix by ensuring we clear the vmid_flag member during lpfc_reinit_vmid, and
check the priority tagging service parameter after reinitialization of the
vmid data structures.
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
fixed clock nodes can't be on the bus because they are missing reg
property. That's why move them to root.
And because it is root it is good to have it as the first node in a file.
Signed-off-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since "dev_search_path" can technically be as large as PATH_MAX,
there was a risk of truncation when copying it and a second string
into "full_path" since it was also PATH_MAX sized. The W=1 builds were
reporting this warning:
drivers/block/rnbd/rnbd-srv.c: In function 'process_msg_open.isra':
drivers/block/rnbd/rnbd-srv.c:616:51: warning: '%s' directive output may be truncated writing up to 254 bytes into a region of size between 0 and 4095 [-Wformat-truncation=]
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~
In function 'rnbd_srv_get_full_path',
inlined from 'process_msg_open.isra' at drivers/block/rnbd/rnbd-srv.c:721:14: drivers/block/rnbd/rnbd-srv.c:616:17: note: 'snprintf' output between 2 and 4351 bytes into a destination of size 4096
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
617 | dev_search_path, dev_name);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
To fix this, unconditionally check for truncation (as was already done
for the case where "%SESSNAME%" was present).
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312100355.lHoJPgKy-lkp@intel.com/ Cc: Md. Haris Iqbal <haris.iqbal@ionos.com> Cc: Jack Wang <jinpu.wang@ionos.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: <linux-block@vger.kernel.org> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev> Acked-by: Jack Wang <jinpu.wang@ionos.com> Link: https://lore.kernel.org/r/20231212214738.work.169-kees@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the driver or firmware is stuck in reset state, don't bother
trying to use adminq commands. This speeds up shutdown and
prevents unnecessary timeouts and error messages.
This includes a bit of rework on ionic_adminq_post_wait()
and ionic_adminq_post_wait_nomsg() to both use
__ionic_adminq_post_wait() which can do the checks needed in
both cases.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't rely on the PCI memory for the devcmd opcode because we
read a 0xff value if the PCI bus is broken, which can cause us
to report a bogus dev_cmd opcode later.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix passing the wrong reference for config_initr on passing the function
pointer, drop the wrong & from at803x_config_intr in the PHY struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
We observe some packets are discarded in ieee80211_rx_handlers_result
function for WCN7850. This is because the way to get multicast/broadcast
indicator with RX_MSDU_END_INFO5_DA_IS_MCBC & info5 is incorrect. It should
use RX_MSDU_END_INFO13_MCAST_BCAST & info13 to get multicast/broadcast
indicator.
Since 'ieee80211_beacon_get()' can return NULL, 'wfx_set_mfp_ap()'
should check the return value before examining skb data. So convert
the latter to return an appropriate error code and propagate it to
return from 'wfx_start_ap()' as well. Compile tested only.
generic_map_{delete,update}_batch() doesn't set uattr->batch.count as
zero before it tries to allocate memory for key. If the memory
allocation fails, the value of uattr->batch.count will be incorrect.
Fix it by setting uattr->batch.count as zero beore batched update or
deletion.
Add a BSS eht_support check before returning EHT phy mode. Without this
patch, there might be an inconsistency where the softmac layer thinks
the BSS is in HE mode, while the FW thinks it is in EHT mode.
In a similar vein to
https://lore.kernel.org/lkml/20220530080842.37024-3-manivannan.sadhasivam@linaro.org/,
the remote processors on sm8350 fail to initialize with the 'correct'
(i.e., specified in downstream) IRQ type. Change this to EDGE_RISING.
Fix the following dt bindings check:
arch/arm64/boot/dts/qcom/sm8450-hdk.dtb: soundwire-controller@31f0000: $nodename:0: 'soundwire-controller@31f0000' does not match '^soundwire(@.*)?$'
from schema $id: http://devicetree.org/schemas/soundwire/qcom,soundwire.yaml#
Fix the following dt bindings check:
arch/arm64/boot/dts/qcom/sm8550-mtp.dtb: soundwire-controller@6ab0000: $nodename:0: 'soundwire-controller@6ab0000' does not match '^soundwire(@.*)?$'
from schema $id: http://devicetree.org/schemas/soundwire/qcom,soundwire.yaml#
Before this change, when operating in polled mode, i.e. no IRQ is
available, every individual C45 access would be hit with a 150us sleep
after the bus access.
For example, on a board with a CN9130 SoC connected to an MV88X3310
PHY, a single C45 read would take around 165us:
root@infix:~$ mdio f212a600.mdio-mii mmd 4:1 bench 0xc003
Performed 1000 reads in 165ms
By replacing the long sleep with a tighter poll loop, we observe a 10x
increase in bus throughput:
root@infix:~$ mdio f212a600.mdio-mii mmd 4:1 bench 0xc003
Performed 1000 reads in 15ms
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20231204100811.2708884-3-tobias@waldekranz.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The type-check in min()/max() is there to stop unexpected results if a
negative value gets converted to a large unsigned value. However it also
rejects 'unsigned int' v 'unsigned long' compares which are common and
never problematc.
Replace the 'same type' check with a 'same signedness' check.
The new test isn't itself a compile time error, so use static_assert() to
report the error and give a meaningful error message.
Due to the way builtin_choose_expr() works detecting the error in the
'non-constant' side (where static_assert() can be used) also detects
errors when the arguments are constant.
Link: https://lkml.kernel.org/r/fe7e6c542e094bfca655abcd323c1c98@AcuMS.aculab.com Signed-off-by: David Laight <david.laight@aculab.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "minmax: Relax type checks in min() and max()", v4.
The min() (etc) functions in minmax.h require that the arguments have
exactly the same types.
However when the type check fails, rather than look at the types and fix
the type of a variable/constant, everyone seems to jump on min_t(). In
reality min_t() ought to be rare - when something unusual is being done,
not normality.
The orginal min() (added in 2.4.9) replaced several inline functions and
included the type - so matched the implicit casting of the function call.
This was renamed min_t() in 2.4.10 and the current min() added. There is
no actual indication that the conversion of negatve values to large
unsigned values has ever been an actual problem.
A quick grep shows 5734 min() and 4597 min_t(). Having the casts on
almost half of the calls shows that something is clearly wrong.
If the wrong type is picked (and it is far too easy to pick the type of
the result instead of the larger input) then significant bits can get
discarded.
Pretty much the worst example is in the derived clamp_val(), consider:
unsigned char x = 200u;
y = clamp_val(x, 10u, 300u);
I also suspect that many of the min_t(u16, ...) are actually wrong. For
example copy_data() in printk_ringbuffer.c contains:
data_size = min_t(u16, buf_size, len);
Here buf_size is 'unsigned int' and len 'u16', pass a 64k buffer (can you
prove that doesn't happen?) and no data is returned. Apparantly it did -
and has since been fixed.
The only reason that most of the min_t() are 'fine' is that pretty much
all the values in the kernel are between 0 and INT_MAX.
Patch 1 adds umin(), this uses integer promotions to convert both
arguments to 'unsigned long long'. It can be used to compare a signed
type that is known to contain a non-negative value with an unsigned type.
The compiler typically optimises it all away. Added first so that it can
be referred to in patch 2.
Patch 2 replaces the 'same type' check with a 'same signedness' one. This
makes min(unsigned_int_var, sizeof()) be ok. The error message is also
improved and will contain the expanded form of both arguments (useful for
seeing how constants are defined).
Patch 3 just fixes some whitespace.
Patch 4 allows comparisons of 'unsigned char' and 'unsigned short' to
signed types. The integer promotion rules convert them both to 'signed
int' prior to the comparison so they can never cause a negative value be
converted to a large positive one.
Patch 5 (rewritted for v4) allows comparisons of unsigned values against
non-negative constant integer expressions. This makes
min(unsigned_int_var, 4) be ok.
The only common case that is still errored is the comparison of signed
values against unsigned constant integer expressions below __INT_MAX__.
Typcally min(int_val, sizeof (foo)), the real fix for this is casting the
constant: min(int_var, (int)sizeof (foo)).
With all the patches applied pretty much all the min_t() could be replaced
by min(), and most of the rest by umin(). However they all need careful
inspection due to code like:
sz = min_t(unsigned char, sz - 1, LIM - 1) + 1;
which converts 0 to LIM.
This patch (of 6):
umin() and umax() can be used when min()/max() errors a signed v unsigned
compare when the signed value is known to be non-negative.
Unlike min_t(some_unsigned_type, a, b) umin() will never mask off high
bits if an inappropriate type is selected.
The '+ 0u + 0ul + 0ull' may look strange.
The '+ 0u' is needed for 'signed int' on 64bit systems.
The '+ 0ul' is needed for 'signed long' on 32bit systems.
The '+ 0ull' is needed for 'signed long long'.
BUILD_BUG_ON*() macros are defined in build_bug.h. Include it. Replace
compiler_types.h by compiler.h, which provides the former, to have a
definition of the __UNIQUE_ID().
It appears that compiler_types.h already have an implementation of the
__unconst_integer_typeof() called __unqual_scalar_typeof(). Use it
instead of the copy.
We should set the status to FC_TIMED_OUT when a timeout error is passed to
fc_fcp_rec_error().
Signed-off-by: Hannes Reinecke <hare@suse.de> Link: https://lore.kernel.org/r/20231129165832.224100-3-hare@kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current FC error recovery is sending up to three REC (recovery) frames
in 10 second intervals, and as a final step sending an ABTS after 30
seconds for the command itself. Unfortunately sending an ABTS is also the
action for the SCSI abort handler, and the default timeout for SCSI
commands is also 30 seconds. This causes two ABTS to be scheduled, with the
libfc one slightly earlier. The ABTS scheduled by SCSI EH then sees the
command to be already aborted, and will always return with a 'GOOD' status
irrespective on the actual result from the first ABTS. This causes the
SCSI EH abort handler to always succeed, and SCSI EH never to be engaged.
Fix this by not issuing an ABTS when a SCSI command is present for the
exchange, but rather wait for the abort scheduled from SCSI EH. And warn
if an abort is already scheduled to avoid similar errors in the future.
Signed-off-by: Hannes Reinecke <hare@suse.de> Link: https://lore.kernel.org/r/20231129165832.224100-2-hare@kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For AP mode, the peer is created earlier in ath12k_mac_op_add_interface() but
ath12k_mac_op_assign_vif_chanctx() will try to create peer again. Then an
error will return which makes AP mode startup fail.
Kernel log:
[ 5017.665006] ath12k_pci 0000:04:00.0: failed to create peer after vdev start delay: -22
wpa_supplicant log:
Failed to set beacon parameters
Interface initialization failed
wls1: interface state UNINITIALIZED->DISABLED
wls1: AP-DISABLED
wls1: Unable to setup interface.
Failed to initialize AP interface
wls1: interface state DISABLED->DISABLED
wls1: AP-DISABLED
So fix this check and enable AP mode for WCN7850, as now AP mode works normally.
Both map deletion operation, map release and map free operation use
fd_array_map_delete_elem() to remove the element from fd array and
need_defer is always true in fd_array_map_delete_elem(). For the map
deletion operation and map release operation, need_defer=true is
necessary, because the bpf program, which accesses the element in fd
array, may still alive. However for map free operation, it is certain
that the bpf program which owns the fd array has already been exited, so
setting need_defer as false is appropriate for map free operation.
So fix it by adding need_defer parameter to bpf_fd_array_map_clear() and
adding a new helper __fd_array_map_delete_elem() to handle the map
deletion, map release and map free operations correspondingly.
These three bpf_map_{lookup,update,delete}_elem() helpers are also
available for sleepable bpf program, so add the corresponding lock
assertion for sleepable bpf program, otherwise the following warning
will be reported when a sleepable bpf program manipulates bpf map under
interpreter mode (aka bpf_jit_enable=0):
In concurrent mode, when STA interface is scanning, it causes
AP interface TX beacon on wrong channel. We modified it to scan
with the operating channel when one of the interfaces is already
connected. Additionally, STA interface need to stop scan when AP
interface is starting to avoid TX beacon on wrong channel. Finally,
AP interface need to stop TX beacon when STA interface is scanning
and switching to non-OP channel,This prevent other device to get
beacons on wrong channel.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231129070046.18443-5-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason is, currently, in ath11k_pcic_ext_irq_enable(),
ATH11K_FLAG_EXT_IRQ_ENABLED is set before NAPI is enabled.
This results in a race condition: after
ATH11K_FLAG_EXT_IRQ_ENABLED is set but before NAPI enabled,
CE interrupt breaks in. Since IRQ is shared by CE and data
path, ath11k_pcic_ext_interrupt_handler() is also called
where we call disable_irq_nosync() to disable IRQ. Then
napi_schedule() is called but it does nothing because NAPI
is not enabled at that time, meaning
ath11k_pcic_ext_grp_napi_poll() will never run, so we have
no chance to call enable_irq() to enable IRQ back. Finally
we get above error.
Fix it by setting ATH11K_FLAG_EXT_IRQ_ENABLED after all
NAPI and IRQ work are done. With the fix, we are sure that
by the time ATH11K_FLAG_EXT_IRQ_ENABLED is set, NAPI is
enabled.
Note that the fix above also introduce some side effects:
if ath11k_pcic_ext_interrupt_handler() breaks in after NAPI
enabled but before ATH11K_FLAG_EXT_IRQ_ENABLED set, nothing
will be done by the handler this time, the work will be
postponed till the next time the IRQ fires.
Fix an array-index-out-of-bounds read in ath9k_htc_txstatus(). The bug
occurs when txs->cnt, data from a URB provided by a USB device, is
bigger than the size of the array txs->txstatus, which is
HTC_MAX_TX_STATUS. WARN_ON() already checks it, but there is no bug
handling code after the check. Make the function return if that is the
case.
Found by a modified version of syzkaller.
UBSAN: array-index-out-of-bounds in htc_drv_txrx.c
index 13 is out of range for type '__wmi_event_txstatus [12]'
Call Trace:
ath9k_htc_txstatus
ath9k_wmi_event_tasklet
tasklet_action_common
__do_softirq
irq_exit_rxu
sysvec_apic_timer_interrupt
Further analysis shows llvm upstream patch [1] is responsible for the above
failures. For example, for function bpf_fentry_test7() in net/bpf/test_run.c,
without [1], the asm code is:
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: nand-controller@33002000:
#size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
The device is always reset two consecutive times (ax88179_reset is called
twice), one from usbnet_probe during the device binding and the other from
usbnet_open.
Remove the non-necessary reset during the device binding and let the reset
operation from open to keep the normal behavior (tested with generic ASIX
Electronics Corp. AX88179 Gigabit Ethernet device).
Reported-by: Herb Wei <weihao.bj@ieisystem.com> Tested-by: Herb Wei <weihao.bj@ieisystem.com> Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Link: https://lore.kernel.org/r/20231120121239.54504-1-jtornosm@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If failed to allocate "tags" or could not find the final upper device from
start_dev's upper list in bond_verify_device_path(), only the loopback
detection of the current upper device should be affected, and the system is
no need to be panic.
So return -ENOMEM in alb_upper_dev_walk to stop walking, print some warn
information when failed to allocate memory for vlan tags in
bond_verify_device_path.
I also think that the following function calls
netdev_walk_all_upper_dev_rcu
---->>>alb_upper_dev_walk
---------->>>bond_verify_device_path
From this way, "end device" can eventually be obtained from "start device"
in bond_verify_device_path, IS_ERR(tags) could be instead of
IS_ERR_OR_NULL(tags) in alb_upper_dev_walk.
Spectrum-{1,2,3,4} devices report that a D3hot->D0 transition causes a
reset (i.e., they advertise NoSoftRst-). However, this transition does
not have any effect on the device: It continues to be operational and
network ports remain up. Advertising this support makes it seem as if a
PM reset is viable for these devices. Mark it as unavailable to skip it
when testing reset methods.
Before:
# cat /sys/bus/pci/devices/0000\:03\:00.0/reset_method
pm bus
After:
# cat /sys/bus/pci/devices/0000\:03\:00.0/reset_method
bus
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of no phc we should not return SOFTWARE TIMESTAMPING flags as we do
not know whether the netdev supports of timestamping.
Remove it from the lan8841_ts_info and simply return 0.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@fa600000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@fa600000: missing or empty reg/ranges property
Subtract 0xfa600000 from all its children nodes. No functional impact
expected.
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@11800000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@11800000: missing or empty reg/ranges property
Subtract 0x11800000 from all its children nodes. No functional impact
expected.
Because file_name and phba->ModelName are both declared a size 80 bytes,
the extra ".grp" file extension could cause an overflow into file_name.
Define a ELX_FW_NAME_SIZE macro with value 84. 84 incorporates the 4 extra
characters from ".grp". file_name is changed to be declared as a char and
initialized to zeros i.e. null chars.
Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20231031191224.150862-3-justintee8345@gmail.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Xen broadcasts SGI to each VM when multiple VMs run on Xen hypervisor. In
such case spurious SGI is expected if one event is registered by one VM and
not registered by another VM. We let users know that Unhandled SGI is not
error and expected if kernel is running on Xen hypervisor.
When preemption is enabled in kernel and if any task which can be
preempted should not use smp_processor_id() directly, since CPU
switch can happen at any time, the previous value of cpu_id
differs with current cpu_id. As a result we see the below call trace
during xlnx_event_manager_probe.
To protect cpu_id, It is recommended to use get_cpu()/put_cpu()
to disable preemption, get the cpu_id and enable preemption respectively.
(For Reference, Documentation/locking/preempt-locking.rst and
Documentation/kernel-hacking/hacking.rst)
Use preempt_disable()/smp_processor_id()/preempt_enable()
API's to achieve the same.
Signed-off-by: HariBabu Gattem <haribabu.gattem@xilinx.com> Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@amd.com> Link: https://lore.kernel.org/r/20231027055622.21544-1-jay.buddhabhatti@amd.com Signed-off-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the vendor DTS files were moved to per-vendor subdirs, there no need
to use common prefixes. Drop the `qcom-' prefix from PMIC dtsi file.
This makes 32-bit qcom/ dts files closer to arm64 ones.
If the net_cls subsystem is already mounted, attempting to mount it again
in setup_classid_environment() will result in a failure with the error code
EBUSY. Despite this, tmpfs will have been successfully mounted at
/sys/fs/cgroup/net_cls. Consequently, the /sys/fs/cgroup/net_cls directory
will be empty, causing subsequent setup operations to fail.
Here's an error log excerpt illustrating the issue when net_cls has already
been mounted at /sys/fs/cgroup/net_cls prior to running
setup_classid_environment():
- Before that change
$ tools/testing/selftests/bpf/test_progs --name=cgroup_v1v2
test_cgroup_v1v2:PASS:server_fd 0 nsec
test_cgroup_v1v2:PASS:client_fd 0 nsec
test_cgroup_v1v2:PASS:cgroup_fd 0 nsec
test_cgroup_v1v2:PASS:server_fd 0 nsec
run_test:PASS:skel_open 0 nsec
run_test:PASS:prog_attach 0 nsec
test_cgroup_v1v2:PASS:cgroup-v2-only 0 nsec
(cgroup_helpers.c:248: errno: No such file or directory) Opening Cgroup Procs: /sys/fs/cgroup/net_cls/cgroup.procs
(cgroup_helpers.c:540: errno: No such file or directory) Opening cgroup classid: /sys/fs/cgroup/net_cls/cgroup-test-work-dir/net_cls.classid
run_test:PASS:skel_open 0 nsec
run_test:PASS:prog_attach 0 nsec
(cgroup_helpers.c:248: errno: No such file or directory) Opening Cgroup Procs: /sys/fs/cgroup/net_cls/cgroup-test-work-dir/cgroup.procs
run_test:FAIL:join_classid unexpected error: 1 (errno 2)
test_cgroup_v1v2:FAIL:cgroup-v1v2 unexpected error: -1 (errno 2)
(cgroup_helpers.c:248: errno: No such file or directory) Opening Cgroup Procs: /sys/fs/cgroup/net_cls/cgroup.procs
#44 cgroup_v1v2:FAIL
Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED
- After that change
$ tools/testing/selftests/bpf/test_progs --name=cgroup_v1v2
#44 cgroup_v1v2:OK
Summary: 1/0 PASSED, 0 SKIPPED, 0 FAILED
Refer to Mediatek vendor driver RxDCOC_Calibration() function, when
performing gainfreeze calibration, we should write register 140
instead of 141. This fix can reduce the total calibration time from
6 seconds to 1 second.
With latest clang18 (main branch of llvm-project repo), when building bpf selftests,
[~/work/bpf-next (master)]$ make -C tools/testing/selftests/bpf LLVM=1 -j
The following compilation error happens:
fatal error: error in backend: Branch target out of insn range
...
Stack dump:
0. Program arguments: clang -g -Wall -Werror -D__TARGET_ARCH_x86 -mlittle-endian
-I/home/yhs/work/bpf-next/tools/testing/selftests/bpf/tools/include
-I/home/yhs/work/bpf-next/tools/testing/selftests/bpf -I/home/yhs/work/bpf-next/tools/include/uapi
-I/home/yhs/work/bpf-next/tools/testing/selftests/usr/include -idirafter
/home/yhs/work/llvm-project/llvm/build.18/install/lib/clang/18/include -idirafter /usr/local/include
-idirafter /usr/include -Wno-compare-distinct-pointer-types -DENABLE_ATOMICS_TESTS -O2 --target=bpf
-c progs/pyperf180.c -mcpu=v3 -o /home/yhs/work/bpf-next/tools/testing/selftests/bpf/pyperf180.bpf.o
1. <eof> parser at end of file
2. Code generation
...
The compilation failure only happens to cpu=v2 and cpu=v3. cpu=v4 is okay
since cpu=v4 supports 32-bit branch target offset.
The above failure is due to upstream llvm patch [1] where some inlining behavior
are changed in clang18.
To workaround the issue, previously all 180 loop iterations are fully unrolled.
The bpf macro __BPF_CPU_VERSION__ (implemented in clang18 recently) is used to avoid
unrolling changes if cpu=v4. If __BPF_CPU_VERSION__ is not available and the
compiler is clang18, the unrollng amount is unconditionally reduced.
Martin reported that there is a libbpf complaining of non-zero-value tail
padding with LIBBPF_OPTS_RESET macro if struct bpf_netkit_opts is modified
to have a 4-byte tail padding. This only happens to clang compiler.
The commend line is: ./test_progs -t tc_netkit_multi_links
Martin and I did some investigation and found this indeed the case and
the following are the investigation details.
Clang:
clang version 18.0.0
<I tried clang15/16/17 and they all have similar results>
tools/lib/bpf/libbpf_common.h:
#define LIBBPF_OPTS_RESET(NAME, ...) \
do { \
memset(&NAME, 0, sizeof(NAME)); \
NAME = (typeof(NAME)) { \
.sz = sizeof(NAME), \
__VA_ARGS__ \
}; \
} while (0)
#endif
tools/lib/bpf/libbpf.h:
struct bpf_netkit_opts {
/* size of this struct, for forward/backward compatibility */
size_t sz;
__u32 flags;
__u32 relative_fd;
__u32 relative_id;
__u64 expected_revision;
size_t :0;
};
#define bpf_netkit_opts__last_field expected_revision
In the above struct bpf_netkit_opts, there is no tail padding.
At -O0 level, the clang compiler creates an intermediate copy.
We have below to store 'flags' with 4-byte store and leave another 4 byte
in the same 8-byte-aligned storage undefined,
5629: c7 85 28 fd ff ff 08 00 00 00 movl $0x8, -0x2d8(%rbp)
and later we store 8-byte to the original zero'ed buffer
5654: 48 8b 85 28 fd ff ff movq -0x2d8(%rbp), %rax
565b: 48 89 45 b0 movq %rax, -0x50(%rbp)
This caused a problem as the 4-byte value at [%rbp-0x2dc, %rbp-0x2e0)
may be garbage.
It is not clear how to resolve the compiler code generation as the compiler
generates correct code w.r.t. how to handle unnamed padding in C standard.
So this patch changed LIBBPF_OPTS_RESET macro to avoid uninitialized tail
padding. We already knows LIBBPF_OPTS macro works on both gcc and clang,
even with tail padding. So LIBBPF_OPTS_RESET is changed to be a
LIBBPF_OPTS followed by a memcpy(), thus avoiding uninitialized tail padding.
In the above code, a temporary buffer is zeroed and then has proper value assigned.
Finally, values in temporary buffer are copied to the original variable buffer,
hence tail padding is guaranteed to be 0.
Signed-off-by: Yonghong Song <yonghong.song@linux.dev> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Tested-by: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/bpf/20231107201511.2548645-1-yonghong.song@linux.dev Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw().
Since 'rtw89_core_tx_kick_off_and_wait()' assumes timeout
(actually RTW89_ROC_TX_TIMEOUT) in milliseconds, I suppose
that RTW89_ROC_IDLE_TIMEOUT is in milliseconds as well. If
so, 'msecs_to_jiffies()' should be used in a call to
'ieee80211_queue_delayed_work()' from 'rtw89_roc_end()'.
Compile tested only.
When we online resize an ext4 filesystem with a oversized flexbg_size,
mkfs.ext4 -F -G 67108864 $dev -b 4096 100M
mount $dev $dir
resize2fs $dev 16G
the following WARN_ON is triggered:
==================================================================
WARNING: CPU: 0 PID: 427 at mm/page_alloc.c:4402 __alloc_pages+0x411/0x550
Modules linked in: sg(E)
CPU: 0 PID: 427 Comm: resize2fs Tainted: G E 6.6.0-rc5+ #314
RIP: 0010:__alloc_pages+0x411/0x550
Call Trace:
<TASK>
__kmalloc_large_node+0xa2/0x200
__kmalloc+0x16e/0x290
ext4_resize_fs+0x481/0xd80
__ext4_ioctl+0x1616/0x1d90
ext4_ioctl+0x12/0x20
__x64_sys_ioctl+0xf0/0x150
do_syscall_64+0x3b/0x90
==================================================================
This is because flexbg_size is too large and the size of the new_group_data
array to be allocated exceeds MAX_ORDER. Currently, the minimum value of
MAX_ORDER is 8, the minimum value of PAGE_SIZE is 4096, the corresponding
maximum number of groups that can be allocated is:
And the value that is down-aligned to the power of 2 is 16384. Therefore,
this value is defined as MAX_RESIZE_BG, and the number of groups added
each time does not exceed this value during resizing, and is added multiple
times to complete the online resizing. The difference is that the metadata
in a flex_bg may be more dispersed.
In commit 967ac8af4475 ("ext4: fix potential integer overflow in
alloc_flex_gd()"), an overflow check is added to alloc_flex_gd() to
prevent the allocated memory from being smaller than expected due to
the overflow. However, after kmalloc() is replaced with kmalloc_array()
in commit 6da2ec56059c ("treewide: kmalloc() -> kmalloc_array()"), the
kmalloc_array() function has an overflow check, so the above problem
will not occur. Therefore, the extra check is removed.
The maximum value of flexbg_size is 2^31, but the maximum value of int
is (2^31 - 1), so overflow may occur when the type of flexbg_size is
declared as int.
For example, when uninit_mask is initialized in ext4_alloc_group_tables(),
if flexbg_size == 2^31, the initialized uninit_mask is incorrect, and this
may causes set_flexbg_block_bitmap() to trigger a BUG_ON().
Therefore, the flexbg_size type is declared as unsigned int to avoid
overflow and memory waste.
Suppose we issue two FITRIM ioctls for ranges [0,15] and [16,31] with
mininum length of trimmed range set to 8 blocks. If we have say a range of
blocks 10-22 free, this range will not be trimmed because it straddles the
boundary of the two FITRIM ranges and neither part is big enough. This is a
bit surprising to some users that call FITRIM on smaller ranges of blocks
to limit impact on the system. Also XFS trims all free space extents that
overlap with the specified range so we are inconsistent among filesystems.
Let's change ext4_try_to_trim_range() to consider for trimming the whole
free space extent that straddles the end of specified range, not just the
part of it within the range.
Even though it seems to be able to resolve some names of
case-insensitive directories, the lack of d_hash and d_compare means we
end up with a broken state in the d_cache. Considering it was never a
goal to support these two together, and we are preparing to use
d_revalidate in case-insensitive filesystems, which would make the
combination even more broken, reject any attempt to get a casefolded
inode from ecryptfs.
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de> Reviewed-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The client was sending an SMB2_CREATE request without setting
OPEN_REPARSE_POINT flag thus failing the entire hardlink operation.
Fix this by setting OPEN_REPARSE_POINT in create options for
SMB2_CREATE request when the source inode is a repase point.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The client was sending an SMB2_CREATE request without setting
OPEN_REPARSE_POINT flag thus failing the entire rename operation.
Fix this by setting OPEN_REPARSE_POINT in create options for
SMB2_CREATE request when the source inode is a repase point.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The problem seems to be that two out of three callers aren't taking the
rcu_read_lock() before calling the list_for_each_entry_rcu() function in
rpc_xprt_switch_has_addr(). I fix this by having
rpc_xprt_switch_has_addr() unconditionaly take the rcu_read_lock(),
which is okay to do recursively in the case that the lock has already
been taken by a caller.
Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When registering tables to the sysctl subsystem there is a check to see
if header is a permanently empty directory (used for mounts). This check
evaluates the first element of the ctl_table. This results in an out of
bounds evaluation when registering empty directories.
The function register_sysctl_mount_point now passes a ctl_table of size
1 instead of size 0. It now relies solely on the type to identify
a permanently empty register.
Make sure that the ctl_table has at least one element before testing for
permanent emptiness.
Signed-off-by: Joel Granados <j.granados@samsung.com> Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202311201431.57aae8f3-oliver.sang@intel.com Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kvm_arch_vcpu_ioctl_set_fpu() allows to set the floating point control
(fpc) register of a guest cpu. The new value is tested for validity by
temporarily loading it into the fpc register.
This may lead to corruption of the fpc register of the host process:
if an interrupt happens while the value is temporarily loaded into the fpc
register, and within interrupt context floating point or vector registers
are used, the current fp/vx registers are saved with save_fpu_regs()
assuming they belong to user space and will be loaded into fp/vx registers
when returning to user space.
test_fp_ctl() restores the original user space / host process fpc register
value, however it will be discarded, when returning to user space.
In result the host process will incorrectly continue to run with the value
that was supposed to be used for a guest cpu.
Fix this by simply removing the test. There is another test right before
the SIE context is entered which will handles invalid values.
This results in a change of behaviour: invalid values will now be accepted
instead of that the ioctl fails with -EINVAL. This seems to be acceptable,
given that this interface is most likely not used anymore, and this is in
addition the same behaviour implemented with the memory mapped interface
(replace invalid values with zero) - see sync_regs() in kvm-s390.c.
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com> Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the content of the floating point control (fpc) register of a traced
process is modified with the ptrace interface the new value is tested for
validity by temporarily loading it into the fpc register.
This may lead to corruption of the fpc register of the tracing process:
if an interrupt happens while the value is temporarily loaded into the
fpc register, and within interrupt context floating point or vector
registers are used, the current fp/vx registers are saved with
save_fpu_regs() assuming they belong to user space and will be loaded into
fp/vx registers when returning to user space.
test_fp_ctl() restores the original user space fpc register value, however
it will be discarded, when returning to user space.
In result the tracer will incorrectly continue to run with the value that
was supposed to be used for the traced process.
Fix this by saving fpu register contents with save_fpu_regs() before using
test_fp_ctl().
The 'status' attribute for AP queue devices bound to the vfio_ap device
driver displays incorrect status when the mediated device is attached to a
guest, but the queue device is not passed through. In the current
implementation, the status displayed is 'in_use' which is not correct; it
should be 'assigned'. This can happen if one of the queue devices
associated with a given adapter is not bound to the vfio_ap device driver.
For example:
Queues listed in /sys/bus/ap/drivers/vfio_ap:
14.0005
14.0006
14.000d
16.0006
16.000d
Queues listed in /sys/devices/vfio_ap/matrix/$UUID/matrix
14.0005
14.0006
14.000d
16.0005
16.0006
16.000d
Queues listed in /sys/devices/vfio_ap/matrix/$UUID/guest_matrix
14.0005
14.0006
14.000d
The reason no queues for adapter 0x16 are listed in the guest_matrix is
because queue 16.0005 is not bound to the vfio_ap device driver, so no
queue associated with the adapter is passed through to the guest;
therefore, each queue device for adapter 0x16 should display 'assigned'
instead of 'in_use', because those queues are not in use by a guest, but
only assigned to the mediated device.
Let's check the AP configuration for the guest to determine whether a
queue device is passed through before displaying a status of 'in_use'.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com> Acked-by: Halil Pasic <pasic@linux.ibm.com> Acked-by: Harald Freudenberger <freude@linux.ibm.com> Link: https://lore.kernel.org/r/20231108201135.351419-1-akrowiak@linux.ibm.com Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The size of vmalloc area depends from various factors
on boot and could be set to:
1. Default size as determined by VMALLOC_DEFAULT_SIZE macro;
2. One half of the virtual address space not occupied by
modules and fixed mappings;
3. The size provided by user with vmalloc= kernel command
line parameter;
In cases [1] and [2] the vmalloc area base address is aligned
on Region3 table type boundary, while in case [3] in might get
aligned on page boundary.
Limit the waste of page tables and always align vmalloc area
size and base address on segment boundary.
projects / thirdparty / kernel / stable.git / log
