dtbs_check throws a warning at the dsi node:
Warning (avoid_unnecessary_addr_size): /soc/dsi@14014000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Other DTS have a panel child node with a reg, so the parent dtsi
must have the address-cells and size-cells, however this specific DT
has the panel removed, but not the cells, hence the warning above.
If panel is deleted then the cells must also be deleted since they are
tied together, as the child node in this DT does not have a reg.
Cc: stable@vger.kernel.org Fixes: cabc71b08eb5 ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board") Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20230814071053.5459-1-eugen.hristev@collabora.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric reports errors on emmc with hs400 mode when booting linux on bpi-r3
without uboot [1]. Booting with uboot does not show this because clocks
seem to be initialized by uboot.
Fix this by adding assigned-clocks and assigned-clock-parents like it's
done in uboot [2].
All SFP power supplies are connected to the system VDD33 which is 3v3/8A.
Set 3A per SFP slot to allow SFPs work which need more power than the
default 1W.
Cc: stable@vger.kernel.org Fixes: 8e01fb15b815 ("arm64: dts: mt7986: add Bananapi R3") Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20231025170832.78727-3-linux@fw-web.de Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.
Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.
Cc: stable@vger.kernel.org Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720 Fixes: 8f4b1068e7fc ("drm/i915: Check some transcoder timing minimum limits") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit e0ef2daa8ca8ce4dbc2fd0959e383b753a87fd7d) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have no bigjoiner support in the MST code, so .mode_valid()
pretending otherwise is just going to result black screens for
users. Reject any mode that needs the joiner.
Invoke drm_plane_helper_funcs.end_fb_access before
drm_atomic_helper_commit_hw_done(). The latter function hands over
ownership of the plane state to the following commit, which might
free it. Releasing resources in end_fb_access then operates on undefined
state. This bug has been observed with non-blocking commits when they
are being queued up quickly.
Here is an example stack trace from the bug report. The plane state has
been free'd already, so the pages for drm_gem_fb_vunmap() are gone.
Unable to handle kernel paging request at virtual address 0000000100000049
[...]
drm_gem_fb_vunmap+0x18/0x74
drm_gem_end_shadow_fb_access+0x1c/0x2c
drm_atomic_helper_cleanup_planes+0x58/0xd8
drm_atomic_helper_commit_tail+0x90/0xa0
commit_tail+0x15c/0x188
commit_work+0x14/0x20
Fix this by running end_fb_access immediately after updating all planes
in drm_atomic_helper_commit_planes(). The existing clean-up helper
drm_atomic_helper_cleanup_planes() now only handles cleanup_fb.
For aborted commits, roll back from drm_atomic_helper_prepare_planes()
in the new helper drm_atomic_helper_unprepare_planes(). This case is
different from regular cleanup, as we have to release the new state;
regular cleanup releases the old state. The new helper also invokes
cleanup_fb for all planes.
The changes mostly involve DRM's atomic helpers. Only two drivers, i915
and nouveau, implement their own commit function. Update them to invoke
drm_atomic_helper_unprepare_planes(). Drivers with custom commit_tail
function do not require changes.
v4:
* fix documentation (kernel test robot)
v3:
* add drm_atomic_helper_unprepare_planes() for rolling back
* use correct state for end_fb_access
v2:
* fix test in drm_atomic_helper_cleanup_planes()
Reported-by: Alyssa Ross <hi@alyssa.is> Closes: https://lore.kernel.org/dri-devel/87leazm0ya.fsf@alyssa.is/ Suggested-by: Daniel Vetter <daniel@ffwll.ch> Fixes: 94d879eaf7fb ("drm/atomic-helper: Add {begin,end}_fb_access to plane helpers") Tested-by: Alyssa Ross <hi@alyssa.is> Reviewed-by: Alyssa Ross <hi@alyssa.is> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Cc: <stable@vger.kernel.org> # v6.2+ Link: https://patchwork.freedesktop.org/patch/msgid/20231204083247.22006-1-tzimmermann@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a reshape or a RAID6 array such as expanding by adding an additional
disk, I/Os to the region of the array which have not yet been reshaped can
stall indefinitely. This is from errors in the stripe_ahead_of_reshape
function causing md to think the I/O is to a region in the actively
undergoing the reshape.
stripe_ahead_of_reshape fails to account for the q disk having a sector
value of 0. By not excluding the q disk from the for loop, raid6 will always
generate a min_sector value of 0, causing a return value which stalls.
The function's max_sector calculation also uses min() when it should use
max(), causing the max_sector value to always be 0. During a backwards
rebuild this can cause the opposite problem where it allows I/O to advance
when it should wait.
Fixing these errors will allow safe I/O to advance in a timely manner and
delay only I/O which is unsafe due to stripes in the middle of undergoing
the reshape.
Fixes: 486f60558607 ("md/raid5: Check all disks in a stripe_head for reshape progress") Cc: stable@vger.kernel.org # v6.0+ Signed-off-by: David Jeffery <djeffery@redhat.com> Tested-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20231128181233.6187-1-djeffery@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The policy returned by cpufreq_cpu_get() has to be released with
the help of cpufreq_cpu_put() to balance its kobject reference counter
properly.
Add the missing calls to cpufreq_cpu_put() in the code.
Fixes: 0aea2e4ec2a2 ("powercap/dtpm_cpu: Reset per_cpu variable in the release function") Fixes: 0e8f68d7f048 ("powercap/drivers/dtpm: Add CPU energy model based support") Cc: v5.16+ <stable@vger.kernel.org> # v5.16+ Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In add_memory_resource(), creation of memory block devices occurs after
successful call to arch_add_memory(). However, creation of memory block
devices could fail. In that case, arch_remove_memory() is called to
perform necessary cleanup.
Currently with or without altmap support, arch_remove_memory() is always
passed with altmap set to NULL during error handling. This leads to
freeing of struct pages using free_pages(), eventhough the allocation
might have been performed with altmap support via
altmap_alloc_block_buf().
Fix the error handling by passing altmap in arch_remove_memory(). This
ensures the following:
* When altmap is disabled, deallocation of the struct pages array occurs
via free_pages().
* When altmap is enabled, deallocation occurs via vmem_altmap_free().
Link: https://lkml.kernel.org/r/20231120145354.308999-3-sumanthk@linux.ibm.com Fixes: a08a2ae34613 ("mm,memory_hotplug: allocate memmap from the added memory range") Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: kernel test robot <lkp@intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: <stable@vger.kernel.org> [5.15+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reports oops in lockdep's __lock_acquire(), called from
__pte_offset_map_lock() called from filemap_map_pages(); or when I run the
repro, the oops comes in pmd_install(), called from filemap_map_pmd()
called from filemap_map_pages(), just before the __pte_offset_map_lock().
The problem is that filemap_map_pmd() has been assuming that when it finds
pmd_none(), a page table has already been prepared in prealloc_pte; and
indeed do_fault_around() has been careful to preallocate one there, when
it finds pmd_none(): but what if *pmd became none in between?
My 6.6 mods in mm/khugepaged.c, avoiding mmap_lock for write, have made it
easy for *pmd to be cleared while servicing a page fault; but even before
those, a huge *pmd might be zapped while a fault is serviced.
The difference in symptomatic stack traces comes from the "memory model"
in use: pmd_install() uses pmd_populate() uses page_to_pfn(): in some
models that is strict, and will oops on the NULL prealloc_pte; in other
models, it will construct a bogus value to be populated into *pmd, then
__pte_offset_map_lock() oops when trying to access split ptlock pointer
(or some other symptom in normal case of ptlock embedded not pointer).
Link: https://lore.kernel.org/linux-mm/20231115065506.19780-1-jose.pekkarinen@foxhound.fi/ Link: https://lkml.kernel.org/r/6ed0c50c-78ef-0719-b3c5-60c0c010431c@google.com Fixes: f9ce0be71d1f ("mm: Cleanup faultaround and finish_fault() codepaths") Signed-off-by: Hugh Dickins <hughd@google.com> Reported-and-tested-by: syzbot+89edd67979b52675ddec@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-mm/0000000000005e44550608a0806c@google.com/ Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Jann Horn <jannh@google.com>, Cc: José Pekkarinen <jose.pekkarinen@foxhound.fi> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> [5.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From Documentation/core-api/memory-hotplug.rst:
When adding/removing/onlining/offlining memory or adding/removing
heterogeneous/device memory, we should always hold the mem_hotplug_lock
in write mode to serialise memory hotplug (e.g. access to global/zone
variables).
mhp_(de)init_memmap_on_memory() functions can change zone stats and
struct page content, but they are currently called w/o the
mem_hotplug_lock.
When memory block is being offlined and when kmemleak goes through each
populated zone, the following theoretical race conditions could occur:
CPU 0: | CPU 1:
memory_offline() |
-> offline_pages() |
-> mem_hotplug_begin() |
... |
-> mem_hotplug_done() |
| kmemleak_scan()
| -> get_online_mems()
| ...
-> mhp_deinit_memmap_on_memory() |
[not protected by mem_hotplug_begin/done()]|
Marks memory section as offline, | Retrieves zone_start_pfn
poisons vmemmap struct pages and updates | and struct page members.
the zone related data |
| ...
| -> put_online_mems()
Fix this by ensuring mem_hotplug_lock is taken before performing
mhp_init_memmap_on_memory(). Also ensure that
mhp_deinit_memmap_on_memory() holds the lock.
online/offline_pages() are currently only called from
memory_block_online/offline(), so it is safe to move the locking there.
Link: https://lkml.kernel.org/r/20231120145354.308999-2-sumanthk@linux.ibm.com Fixes: a08a2ae34613 ("mm,memory_hotplug: allocate memmap from the added memory range") Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: kernel test robot <lkp@intel.com> Cc: <stable@vger.kernel.org> [5.15+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 88a6f8994421 ("crash: memory and CPU hotplug sysfs
attributes"), on x86_64, if only below kernel configs related to kdump are
set, compiling error are triggered.
------------------------------------------------------
drivers/base/cpu.c: In function `crash_hotplug_show':
drivers/base/cpu.c:309:40: error: implicit declaration of function `crash_hotplug_cpu_support'; did you mean `crash_hotplug_show'? [-Werror=implicit-function-declaration]
309 | return sysfs_emit(buf, "%d\n", crash_hotplug_cpu_support());
| ^~~~~~~~~~~~~~~~~~~~~~~~~
| crash_hotplug_show
cc1: some warnings being treated as errors
------------------------------------------------------
CONFIG_KEXEC is used to enable kexec_load interface, the
crash_notes/crash_notes_size/crash_hotplug showing depends on
CONFIG_KEXEC is incorrect. It should depend on KEXEC_CORE instead.
Fix it now.
Link: https://lkml.kernel.org/r/20231128055248.659808-1-bhe@redhat.com Fixes: 88a6f8994421 ("crash: memory and CPU hotplug sysfs attributes") Signed-off-by: Baoquan He <bhe@redhat.com> Tested-by: Ignat Korchagin <ignat@cloudflare.com> [compile-time only] Tested-by: Alexander Gordeev <agordeev@linux.ibm.com> Reviewed-by: Eric DeVolder <eric_devolder@yahoo.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The routine __vma_private_lock tests for the existence of a reserve map
associated with a private hugetlb mapping. A pointer to the reserve map
is in vma->vm_private_data. __vma_private_lock was checking the pointer
for NULL. However, it is possible that the low bits of the pointer could
be used as flags. In such instances, vm_private_data is not NULL and not
a valid pointer. This results in the null-ptr-deref reported by syzbot:
Mask off low bit flags before checking for NULL pointer. In addition, the
reserve map only 'belongs' to the OWNER (parent in parent/child
relationships) so also check for the OWNER flag.
Link: https://lkml.kernel.org/r/20231114012033.259600-1-mike.kravetz@oracle.com Reported-by: syzbot+6ada951e7c0f7bc8a71e@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-mm/00000000000078d1e00608d7878b@google.com/ Fixes: bf4916922c60 ("hugetlbfs: extend hugetlb_vma_lock to private VMAs") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Rik van Riel <riel@surriel.com> Cc: Edward Adam Davis <eadavis@qq.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Tom Rix <trix@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During boot, depending on how the housekeeping and workqueue.unbound_cpus
masks are set, wq_unbound_cpumask can end up empty. Since 8639ecebc9b1
("workqueue: Implement non-strict affinity scope for unbound workqueues"),
this may end up feeding -1 as a CPU number into scheduler leading to oopses.
An empty wq_unbound_cpumask is a clear misconfiguration and already
disallowed once system is booted up. Let's warn on and ignore
unbound_cpumask restrictions which lead to no unbound cpus. While at it,
also remove now unncessary empty check on wq_unbound_cpumask in
wq_select_unbound_cpu().
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return negative number in case of issue, when
ssam_controller_receive_buf() returns ESHUTDOWN just returns 0, e.g. no
bytes consumed, this keep the exact same behavior as it was before.
This fixes a potential WARN in serdev-ttyport.c:ttyport_receive_buf().
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Cc: stable@vger.kernel.org Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20231128194935.11350-1-francesco@dolcini.it Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0ec7731655de ("regmap: Ensure range selector registers
are updated after cache sync") opening pcm512x based soundcards fail
with EINVAL and dmesg shows sync cache and pm_runtime_get errors:
[ 228.794676] pcm512x 1-004c: Failed to sync cache: -22
[ 228.794740] pcm512x 1-004c: ASoC: error at snd_soc_pcm_component_pm_runtime_get on pcm512x.1-004c: -22
This is caused by the cache check result leaking out into the
regcache_sync return value.
Fix this by making the check local-only, as the comment above the
regcache_read call states a non-zero return value means there's
nothing to do so the return value should not be altered.
Fixes: 0ec7731655de ("regmap: Ensure range selector registers are updated after cache sync") Cc: stable@vger.kernel.org Signed-off-by: Matthias Reichl <hias@horus.com> Link: https://lore.kernel.org/r/20231203222216.96547-1-hias@horus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When FIFO reaches near full state, device will issue pause frame.
If pause slot is enabled(set to 1), in this time, device will issue
pause frame only once. But if pause slot is disabled(set to 0), device
will keep sending pause frames until FIFO reaches near empty state.
When pause slot is disabled, if there is no one to handle receive
packets, device FIFO will reach near full state and keep sending
pause frames. That will impact entire local area network.
This issue can be reproduced in Chromebox (not Chromebook) in
developer mode running a test image (and v5.10 kernel):
1) ping -f $CHROMEBOX (from workstation on same local network)
2) run "powerd_dbus_suspend" from command line on the $CHROMEBOX
3) ping $ROUTER (wait until ping fails from workstation)
Takes about ~20-30 seconds after step 2 for the local network to
stop working.
Fix this issue by enabling pause slot to only send pause frame once
when FIFO reaches near full state.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125") Reported-by: Grant Grundler <grundler@chromium.org> Tested-by: Grant Grundler <grundler@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: ChunHao Lin <hau@realtek.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/20231129155350.5843-1-hau@realtek.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some potential instances the reference count on struct packet_sock
could be saturated and cause overflows which gets the kernel a bit
confused. To prevent this, move to a 64-bit atomic reference count on
64-bit architectures to prevent the possibility of this type to overflow.
Because we can not handle saturation, using refcount_t is not possible
in this place. Maybe someday in the future if it changes it could be
used. Also, instead of using plain atomic64_t, use atomic_long_t instead.
32-bit machines tend to be memory-limited (i.e. anything that increases
a reference uses so much memory that you can't actually get to 2**32
references). 32-bit architectures also tend to have serious problems
with 64-bit atomics. Hence, atomic_long_t is the more natural solution.
Reported-by: "The UK's National Cyber Security Centre (NCSC)" <security@ncsc.gov.uk> Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@kernel.org Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231201131021.19999-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The neighbour event callback call the function nfp_tun_write_neigh,
this function will take a mutex lock and it is in soft irq context,
change the work queue to process the neighbour event.
Move the nfp_tun_write_neigh function out of range rcu_read_lock/unlock()
in function nfp_tunnel_request_route_v4 and nfp_tunnel_request_route_v6.
Fixes: abc210952af7 ("nfp: flower: tunnel neigh support bond offload") CC: stable@vger.kernel.org # 6.2+ Signed-off-by: Hui Zhou <hui.zhou@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When working on LED support for r8169 I got the following lockdep
warning. Easiest way to prevent this scenario seems to be to take
the RTNL lock before the trigger_data lock in set_device_name().
======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc2-next-20231124+ #2 Not tainted
------------------------------------------------------
bash/383 is trying to acquire lock: ffff888103aa1c68 (&trigger_data->lock){+.+.}-{3:3}, at: netdev_trig_notify+0xec/0x190 [ledtrig_netdev]
but task is already holding lock: ffffffff8cddf808 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x12/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Function trace_buffered_event_disable() is responsible for freeing pages
backing buffered events and this process can run concurrently with
trace_event_buffer_lock_reserve().
The following race is currently possible:
* Function trace_buffered_event_disable() is called on CPU 0. It
increments trace_buffered_event_cnt on each CPU and waits via
synchronize_rcu() for each user of trace_buffered_event to complete.
* After synchronize_rcu() is finished, function
trace_buffered_event_disable() has the exclusive access to
trace_buffered_event. All counters trace_buffered_event_cnt are at 1
and all pointers trace_buffered_event are still valid.
* At this point, on a different CPU 1, the execution reaches
trace_event_buffer_lock_reserve(). The function calls
preempt_disable_notrace() and only now enters an RCU read-side
critical section. The function proceeds and reads a still valid
pointer from trace_buffered_event[CPU1] into the local variable
"entry". However, it doesn't yet read trace_buffered_event_cnt[CPU1]
which happens later.
* Function trace_buffered_event_disable() continues. It frees
trace_buffered_event[CPU1] and decrements
trace_buffered_event_cnt[CPU1] back to 0.
* Function trace_event_buffer_lock_reserve() continues. It reads and
increments trace_buffered_event_cnt[CPU1] from 0 to 1. This makes it
believe that it can use the "entry" that it already obtained but the
pointer is now invalid and any access results in a use-after-free.
Fix the problem by making a second synchronize_rcu() call after all
trace_buffered_event values are set to NULL. This waits on all potential
users in trace_event_buffer_lock_reserve() that still read a previous
pointer from trace_buffered_event.
For instance, it can be triggered by running these two commands in
parallel:
$ while true; do
echo hist:key=id.syscall:val=hitcount > \
/sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/trigger;
done
$ stress-ng --sysinfo $(nproc)
The warning indicates that the current ring_buffer_per_cpu is not in the
committing state. It happens because the active ring_buffer_event
doesn't actually come from the ring_buffer_per_cpu but is allocated from
trace_buffered_event.
The bug is in function trace_buffered_event_disable() where the
following normally happens:
* The code invokes disable_trace_buffered_event() via
smp_call_function_many() and follows it by synchronize_rcu(). This
increments the per-CPU variable trace_buffered_event_cnt on each
target CPU and grants trace_buffered_event_disable() the exclusive
access to the per-CPU variable trace_buffered_event.
* Maintenance is performed on trace_buffered_event, all per-CPU event
buffers get freed.
* The code invokes enable_trace_buffered_event() via
smp_call_function_many(). This decrements trace_buffered_event_cnt and
releases the access to trace_buffered_event.
A problem is that smp_call_function_many() runs a given function on all
target CPUs except on the current one. The following can then occur:
* Task X executing trace_buffered_event_disable() runs on CPU 0.
* The control reaches synchronize_rcu() and the task gets rescheduled on
another CPU 1.
* The RCU synchronization finishes. At this point,
trace_buffered_event_disable() has the exclusive access to all
trace_buffered_event variables except trace_buffered_event[CPU0]
because trace_buffered_event_cnt[CPU0] is never incremented and if the
buffer is currently unused, remains set to 0.
* A different task Y is scheduled on CPU 0 and hits a trace event. The
code in trace_event_buffer_lock_reserve() sees that
trace_buffered_event_cnt[CPU0] is set to 0 and decides the use the
buffer provided by trace_buffered_event[CPU0].
* Task X continues its execution in trace_buffered_event_disable(). The
code incorrectly frees the event buffer pointed by
trace_buffered_event[CPU0] and resets the variable to NULL.
* Task Y writes event data to the now freed buffer and later detects the
created inconsistency.
The issue is observable since commit dea499781a11 ("tracing: Fix warning
in trace_buffered_event_disable()") which moved the call of
trace_buffered_event_disable() in __ftrace_event_enable_disable()
earlier, prior to invoking call->class->reg(.. TRACE_REG_UNREGISTER ..).
The underlying problem in trace_buffered_event_disable() is however
present since the original implementation in commit 0fc1b09ff1ff
("tracing: Use temp buffer when filtering events").
Fix the problem by replacing the two smp_call_function_many() calls with
on_each_cpu_mask() which invokes a given callback on all CPUs.
It use to be that only the top level instance had a snapshot buffer (for
latency tracers like wakeup and irqsoff). When stopping a tracer in an
instance would not disable the snapshot buffer. This could have some
unintended consequences if the irqsoff tracer is enabled.
Consolidate the tracing_start/stop() with tracing_start/stop_tr() so that
all instances behave the same. The tracing_start/stop() functions will
just call their respective tracing_start/stop_tr() with the global_array
passed in.
Link: https://lkml.kernel.org/r/20231205220011.041220035@goodmis.org Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 6d9b3fa5e7f6 ("tracing: Move tracing_max_latency into trace_array") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ring buffer is being resized, it can cause side effects to the
running tracer. For instance, there's a race with irqsoff tracer that
swaps individual per cpu buffers between the main buffer and the snapshot
buffer. The resize operation modifies the main buffer and then the
snapshot buffer. If a swap happens in between those two operations it will
break the tracer.
Simply stop the running tracer before resizing the buffers and enable it
again when finished.
Link: https://lkml.kernel.org/r/20231205220010.748996423@goodmis.org Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 3928a8a2d9808 ("ftrace: make work with new ring buffer") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It use to be that only the top level instance had a snapshot buffer (for
latency tracers like wakeup and irqsoff). The update of the ring buffer
size would check if the instance was the top level and if so, it would
also update the snapshot buffer as it needs to be the same as the main
buffer.
Now that lower level instances also has a snapshot buffer, they too need
to update their snapshot buffer sizes when the main buffer is changed,
otherwise the following can be triggered:
All addresses printed by checkstack have an extra incorrect 0 appended at
the end.
This was introduced with commit 677f1410e058 ("scripts/checkstack.pl: don't
display $dre as different entity"): since then the address is taken from
the line which contains the function name, instead of the line which
contains stack consumption. E.g. on s390:
So the used regex which matches spaces and hexadecimal numbers to extract
an address now matches a different substring. Subsequently replacing spaces
with 0 appends a zero at the and, instead of replacing leading spaces.
Fix this by using the proper regex, and simplify the code a bit.
__thaw_task() was recently updated to warn if the task being thawed was
part of a freezer cgroup that is still currently freezing:
void __thaw_task(struct task_struct *p)
{
...
if (WARN_ON_ONCE(freezing(p)))
goto unlock;
This has exposed a bug in cgroup1 freezing where when CGROUP_FROZEN is
asserted, the CGROUP_FREEZING bits are not also cleared at the same
time. Meaning, when a cgroup is marked FROZEN it continues to be marked
FREEZING as well. This causes the WARNING to trigger, because
cgroup_freezing() thinks the cgroup is still freezing.
There are two ways to fix this:
1. Whenever FROZEN is set, clear FREEZING for the cgroup and all
children cgroups.
2. Update cgroup_freezing() to also verify that FROZEN is not set.
This patch implements option (2), since it's smaller and more
straightforward.
Signed-off-by: Tim Van Patten <timvp@google.com> Tested-by: Mark Hasemeyer <markhas@chromium.org> Fixes: f5d39b020809 ("freezer,sched: Rewrite core freezer logic") Cc: stable@vger.kernel.org # v6.1+ Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
group_cpus_evenly() could be part of storage driver's error handler, such
as nvme driver, when may happen during CPU hotplug, in which storage queue
has to drain its pending IOs because all CPUs associated with the queue
are offline and the queue is becoming inactive. And handling IO needs
error handler to provide forward progress.
Then deadlock is caused:
1) inside CPU hotplug handler, CPU hotplug lock is held, and blk-mq's
handler is waiting for inflight IO
2) error handler is waiting for CPU hotplug lock
3) inflight IO can't be completed in blk-mq's CPU hotplug handler
because error handling can't provide forward progress.
Solve the deadlock by not holding CPU hotplug lock in group_cpus_evenly(),
in which two stage spreads are taken: 1) the 1st stage is over all present
CPUs; 2) the end stage is over all other CPUs.
Turns out the two stage spread just needs consistent 'cpu_present_mask',
and remove the CPU hotplug lock by storing it into one local cache. This
way doesn't change correctness, because all CPUs are still covered.
Link: https://lkml.kernel.org/r/20231120083559.285174-1-ming.lei@redhat.com Signed-off-by: Ming Lei <ming.lei@redhat.com> Reported-by: Yi Zhang <yi.zhang@redhat.com> Reported-by: Guangwu Zhang <guazhang@redhat.com> Tested-by: Guangwu Zhang <guazhang@redhat.com> Reviewed-by: Chengming Zhou <zhouchengming@bytedance.com> Reviewed-by: Jens Axboe <axboe@kernel.dk> Cc: Keith Busch <kbusch@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If nilfs2 reads a disk image with corrupted segment usage metadata, and
its segment usage information is marked as an error for the segment at the
write location, nilfs_sufile_set_segment_usage() can trigger WARN_ONs
during log writing.
Segments newly allocated for writing with nilfs_sufile_alloc() will not
have this error flag set, but this unexpected situation will occur if the
segment indexed by either nilfs->ns_segnum or nilfs->ns_nextnum (active
segment) was marked in error.
Fix this issue by inserting a sanity check to treat it as a file system
corruption.
Since error returns are not allowed during the execution phase where
nilfs_sufile_set_segment_usage() is used, this inserts the sanity check
into nilfs_sufile_mark_dirty() which pre-reads the buffer containing the
segment usage record to be updated and sets it up in a dirty state for
writing.
In addition, nilfs_sufile_set_segment_usage() is also called when
canceling log writing and undoing segment usage update, so in order to
avoid issuing the same kernel warning in that case, in case of
cancellation, avoid checking the error flag in
nilfs_sufile_set_segment_usage().
When mounting a filesystem image with a block size larger than the page
size, nilfs2 repeatedly outputs long error messages with stack traces to
the kernel log, such as the following:
This overloads the system logger. And to make matters worse, it sometimes
crashes the kernel with a memory access violation.
This is because the return value of the sb_set_blocksize() call, which
should be checked for errors, is not checked.
The latter issue is due to out-of-buffer memory being accessed based on a
large block size that caused sb_set_blocksize() to fail for buffers read
with the initial minimum block size that remained unupdated in the
super_block structure.
Since nilfs2 mkfs tool does not accept block sizes larger than the system
page size, this has been overlooked. However, it is possible to create
this situation by intentionally modifying the tool or by passing a
filesystem image created on a system with a large page size to a system
with a smaller page size and mounting it.
Fix this issue by inserting the expected error handling for the call to
sb_set_blocksize().
Clang static checker complains that value stored to 'from' is never read.
And memcpy_from_folio() only copy the last chunk memory from folio to
destination. Use 'to += chunk' to replace 'from += chunk' to fix this
typo problem.
Link: https://lkml.kernel.org/r/20231130034017.1210429-1-suhui@nfschina.com Fixes: b23d03ef7af5 ("highmem: add memcpy_to_folio() and memcpy_from_folio()") Signed-off-by: Su Hui <suhui@nfschina.com> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Tom Rix <trix@redhat.com> Cc: Tony Luck <tony.luck@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a race where if an event is discarded from the ring buffer and an
interrupt were to happen at that time and insert an event, the time stamp
is still used from the discarded event as an offset. This can screw up the
timings.
If the event is going to be discarded, set the "before_stamp" to zero.
When a new event comes in, it compares the "before_stamp" with the
"write_stamp" and if they are not equal, it will insert an absolute
timestamp. This will prevent the timings from getting out of sync due to
the discarded event.
Link: https://lore.kernel.org/linux-trace-kernel/20231206100244.5130f9b3@gandalf.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 6f6be606e763f ("ring-buffer: Force before_stamp and write_stamp to be different on discard") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 64 bit cmpxchg() is very expensive on 32bit architectures, the
timestamp used by the ring buffer does some interesting tricks to be able
to still have an atomic 64 bit number. It originally just used 60 bits and
broke it up into two 32 bit words where the extra 2 bits were used for
synchronization. But this was not enough for all use cases, and all 64
bits were required.
The 32bit version of the ring buffer timestamp was then broken up into 3
32bit words using the same counter trick. But one update was not done. The
check to see if the read operation was done without interruption only
checked the first two words and not last one (like it had before this
update). Fix it by making sure all three updates happen without
interruption by comparing the initial counter with the last updated
counter.
Link: https://lore.kernel.org/linux-trace-kernel/20231206100050.3100b7bb@gandalf.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: f03f2abce4f39 ("ring-buffer: Have 32 bit time stamps use all 64 bits") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Framework Laptop 13 (AMD Ryzen 7040Series) has an ALC295 with
a disconnected or faulty headset mic presence detect similar to the
previous models. It works with the same quirk chain as 309d7363ca3d9fcdb92ff2d958be14d7e8707f68. This model has a VID:PID
of f111:0006.
XPS 9530 has 2 tweeters and 2 subwoofers powered by CS35L41 amplifier, SPI
connected. For subwoofers to work, it requires both to enable amplifier
support, and to enable output to subwoofers via 0x17 quirk (similalry to
XPS 9510/9520).
The pcm state can be SNDRV_PCM_STATE_DISCONNECTED at disconnect
callback, and there is not an entry of SNDRV_PCM_STATE_DISCONNECTED
in snd_pcm_state_names.
This patch adds the missing entry to resolve this issue.
cat /proc/asound/card2/pcm0p/sub0/status
That results in stack traces like the following:
These values mirror those of the Pioneer DJM-250MK2 as the channel layout
appears identical based on my observations. This duplication could be removed in
later contributions if desired.
Signed-off-by: Sarah Grant <s@srd.tw> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20231201181654.5058-1-s@srd.tw Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Callers of mutex_unlock() have to make sure that the mutex stays alive
for the whole duration of the function call. For io_uring that means
that the following pattern is not valid unless we ensure that the
context outlives the mutex_unlock() call.
mutex_lock(&ctx->uring_lock);
req_put(req); // typically via io_req_task_submit()
mutex_unlock(&ctx->uring_lock);
Most contexts are fine: io-wq pins requests, syscalls hold the file,
task works are taking ctx references and so on. However, the task work
fallback path doesn't follow the rule.
Cc: <stable@vger.kernel.org> Fixes: 04fc6c802d ("io_uring: save ctx put/get for task_work submit") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Link: https://lore.kernel.org/io-uring/CAG48ez3xSoYb+45f1RLtktROJrpiDQ1otNvdR+YLQf7m+Krj5Q@mail.gmail.com/ Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
File reference cycles have caused lots of problems for io_uring
in the past, and it still doesn't work exactly right and races with
unix_stream_read_generic(). The safest fix would be to completely
disallow sending io_uring files via sockets via SCM_RIGHT, so there
are no possible cycles invloving registered files and thus rendering
SCM accounting on the io_uring side unnecessary.
This patch adds ASUSTeK COMPUTER INC "E1504FA" to the quirks file acp6x-mach.c
to enable microphone array on ASUS Vivobook GO 15.
I have this laptop and can confirm that the patch succeeds in enabling the
microphone array.
Since the rethook::handler is an RCU-maganged pointer so that it will
notice readers the rethook is stopped (unregistered) or not, it should
be an __rcu pointer and use appropriate functions to be accessed. This
will use appropriate memory barrier when accessing it. OTOH,
rethook::data is never changed, so we don't need to check it in
get_kretprobe().
NOTE: To avoid sparse warning, rethook::handler is defined by a raw
function pointer type with __rcu instead of rethook_handler_t.
After the conversion to bus_to_subsys() and class_to_subsys(), the gdb
scripts listing the system buses and classes respectively was broken, fix
those by returning the subsys_priv pointer and have the various caller
de-reference either the 'bus' or 'class' structure members accordingly.
Link: https://lkml.kernel.org/r/20231130043317.174188-1-florian.fainelli@broadcom.com Fixes: 7b884b7f24b4 ("driver core: class.c: convert to only use class_to_subsys") Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Tested-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Kieran Bingham <kbingham@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ignat Korchagin complained that a potential config regression was
introduced by commit 89cde455915f ("kexec: consolidate kexec and crash
options into kernel/Kconfig.kexec"). Before the commit, CONFIG_CRASH_DUMP
has no dependency on CONFIG_KEXEC. After the commit, CRASH_DUMP selects
KEXEC. That enforces system to have CONFIG_KEXEC=y as long as
CONFIG_CRASH_DUMP=Y which people may not want.
In Ignat's case, he sets CONFIG_CRASH_DUMP=y, CONFIG_KEXEC_FILE=y and
CONFIG_KEXEC=n because kexec_load interface could have security issue if
kernel/initrd has no chance to be signed and verified.
CRASH_DUMP has select of KEXEC because Eric, author of above commit, met a
LKP report of build failure when posting patch of earlier version. Please
see below link to get detail of the LKP report:
In fact, that LKP report is triggered because arm's <asm/kexec.h> is
wrapped in CONFIG_KEXEC ifdeffery scope. That is wrong. CONFIG_KEXEC
controls the enabling/disabling of kexec_load interface, but not kexec
feature. Removing the wrongly added CONFIG_KEXEC ifdeffery scope in
<asm/kexec.h> of arm allows us to drop the select KEXEC for CRASH_DUMP.
Meanwhile, change arch/arm/kernel/Makefile to let machine_kexec.o
relocate_kernel.o depend on KEXEC_CORE.
Link: https://lkml.kernel.org/r/20231128054457.659452-1-bhe@redhat.com Fixes: 89cde455915f ("kexec: consolidate kexec and crash options into kernel/Kconfig.kexec") Signed-off-by: Baoquan He <bhe@redhat.com> Reported-by: Ignat Korchagin <ignat@cloudflare.com> Tested-by: Ignat Korchagin <ignat@cloudflare.com> [compile-time only] Tested-by: Alexander Gordeev <agordeev@linux.ibm.com> Reviewed-by: Eric DeVolder <eric_devolder@yahoo.com> Tested-by: Eric DeVolder <eric_devolder@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If md_set_readonly() failed, the array could still be read-write, however
'MD_RECOVERY_FROZEN' could still be set, which leave the array in an
abnormal state that sync or recovery can't continue anymore.
Hence make sure the flag is cleared after md_set_readonly() returns.
Fixes: 88724bfa68be ("md: wait for pending superblock updates before switching to read-only") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20231205094215.1824240-3-yukuai1@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to probe for IOCP only once during boot stage, as we were probing
for IOCP for all the stages this caused the below issue during module-init
stage,
This is because we called riscv_noncoherent_supported() for all the stages
during IOCP probe. riscv_noncoherent_supported() function sets
noncoherent_supported variable to true which has an annotation set to
"__ro_after_init" due to which we were seeing the above splat. Fix this by
probing for IOCP only once in boot stage by having a boolean variable
"done" which will be set to true upon IOCP probe in errata_probe_iocp()
and we bail out early if "done" is set to true.
While at it make return type of errata_probe_iocp() to void as we were
not checking the return value in andes_errata_patch_func().
Fixes: e021ae7f5145 ("riscv: errata: Add Andes alternative ports") Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com> Link: https://lore.kernel.org/r/20231130212647.108746-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
JEDEC standard JESD84-B51 defines the eMMC Data Strobe line, which is
currently used only in HS400 mode, as a device->host clock signal that
"is used only in read operation. The Data Strobe is always High-Z (not
driven by the device and pulled down by RDS) or Driven Low in write
operation, except during CRC status response." RDS is a pull-down
resistor specified in the 10K-100K ohm range. Thus per the standard, the
Data Strobe is always pulled to ground (by the eMMC and/or RDS) during
write operations.
Evidently, the eMMC host controller in the RK3588 considers an active
voltage on the eMMC-DS line during a write to be an error.
The default (i.e. hardware reset, and Rockchip BSP) behavior for the
RK3588 is to activate the eMMC-DS pin's builtin pull-down. As a result,
many RK3588 board designers do not bother adding a dedicated RDS
resistor, instead relying on the RK3588's internal bias. The current
devicetree, however, disables this bias (`pcfg_pull_none`), breaking
HS400-mode writes for boards without a dedicated RDS, but with an eMMC
chip that chooses to High-Z (instead of drive-low) the eMMC-DS line.
(The Turing RK1 is one such board.)
Fix this by changing the bias in the (common) emmc_data_strobe case to
reflect the expected hardware/BSP behavior. This is unlikely to cause
regressions elsewhere: the pull-down is only relevant for High-Z eMMCs,
and if this is redundant with a (dedicated) RDS resistor, the effective
result is only a lower resistance to ground -- where the range of
tolerance is quite high. If it does, it's better fixed in the specific
devicetrees.
The timer nodes declare compatibility with "fsl,imx6sx-gpt", which
itself is compatible with "fsl,imx6dl-gpt". Switch the fallback
compatible from "fsl,imx6sx-gpt" to "fsl,imx6dl-gpt".
Make sure that the wifi regulator is always on. The wifi driver itself
puts the wifi module into suspend mode. If we cut the power the driver
will crash when resuming from suspend.
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
Release the id allocated in 'mmdc_pmu_init' when 'devm_kasprintf'
return NULL
"nic_media" clock should be enabled when power on/off mediamix, otherwise
power on/off will fail. Because "media_axi_root" clock is the parent of
"nic_media" clock, so replace "media_axi_clock" clock with "nic_media"
clock in mediamix node.
imx8qm-apalis-v1.1-ixora-v1.2.dtb: pwm@5d000000: 'oneOf' conditional failed, one must be fixed:
'interrupts' is a required property
'interrupts-extended' is a required property
from schema $id: http://devicetree.org/schemas/pwm/imx-pwm.yaml#
When an error occurs in the for loop of beiscsi_init_wrb_handle(), we
should free phwi_ctxt->be_wrbq before returning an error code to prevent
potential memleak.
Fixes: a7909b396ba7 ("[SCSI] be2iscsi: Fix dynamic CID allocation Mechanism in driver") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20231123081941.24854-1-dinghao.liu@zju.edu.cn Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function trace_buffered_event_disable() produces an unexpected warning
when the previous call to trace_buffered_event_enable() fails to
allocate pages for buffered events.
The situation can occur as follows:
* The counter trace_buffered_event_ref is at 0.
* The soft mode gets enabled for some event and
trace_buffered_event_enable() is called. The function increments
trace_buffered_event_ref to 1 and starts allocating event pages.
* The allocation fails for some page and trace_buffered_event_disable()
is called for cleanup.
* Function trace_buffered_event_disable() decrements
trace_buffered_event_ref back to 0, recognizes that it was the last
use of buffered events and frees all allocated pages.
* The control goes back to trace_buffered_event_enable() which returns.
The caller of trace_buffered_event_enable() has no information that
the function actually failed.
* Some time later, the soft mode is disabled for the same event.
Function trace_buffered_event_disable() is called. It warns on
"WARN_ON_ONCE(!trace_buffered_event_ref)" and returns.
Buffered events are just an optimization and can handle failures. Make
trace_buffered_event_enable() exit on the first failure and left any
cleanup later to when trace_buffered_event_disable() is called.
Since commit c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK
specific PHY fixup")thet Ethernet PHY is no longer configured via code
in board file.
This caused Ethernet to stop working.
Fix this problem by describing the clocks and clock-names to the
Ethernet PHY node so that the KSZ8081 chip can be clocked correctly.
The i.MX8MP and i.MX8MQ devices both use the same DWC3 controller and
are both affected by a known issue with the controller due to specific
behaviour when park mode is enabled in SuperSpeed host mode operation.
Under heavy USB traffic from multiple endpoints the controller will
sometimes incorrectly process transactions such that some transactions
are lost, or the controller may hang when processing transactions. When
the controller hangs it does not recover.
This issue is documented partially within the linux-imx vendor kernel
which references a Synopsys STAR number 9001415732 in commits [1] and
additional details in [2]. Those commits provide some additional
controller internal implementation specifics around the incorrect
behaviour of the SuperSpeed host controller operation when park mode is
enabled.
The summary of this issue is that the host controller can incorrectly
enter/exit park mode such that part of the controller is in a state
which behaves as if in park mode even though it is not. In this state
the controller incorrectly calculates the number of TRBs available which
results in incorrect access of the internal caches causing the overwrite
of pending requests in the cache which should have been processed but
are ignored. This can cause the controller to drop the requests or hang
waiting for the pending state of the dropped requests.
The workaround for this issue is to disable park mode for SuperSpeed
operation of the controller through the GUCTL1[17] bit. This is already
available as a quirk for the DWC3 controller and can be enabled via the
'snps,parkmode-disable-ss-quirk' device tree property.
It is possible to replicate this failure on an i.MX8MP EVK with a USB
Hub connecting 4 SuperSpeed USB flash drives. Performing continuous
small read operations (dd if=/dev/sd... of=/dev/null bs=16) on the block
devices will result in device errors initially and will eventually
result in the controller hanging.
[13240.896936] xhci-hcd xhci-hcd.0.auto: WARN Event TRB for slot 4 ep 2 with no TDs queued?
[13240.990708] usb 2-1.3: reset SuperSpeed USB device number 5 using xhci-hcd
[13241.015582] sd 2:0:0:0: [sdc] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x07 driverbyte=DRIVER_OK cmd_age=0s
[13241.025198] sd 2:0:0:0: [sdc] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
[13241.032949] I/O error, dev sdc, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 25 prio class 2
[13272.150710] usb 2-1.2: reset SuperSpeed USB device number 4 using xhci-hcd
[13272.175469] sd 1:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x03 driverbyte=DRIVER_OK cmd_age=31s
[13272.185365] sd 1:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
[13272.193385] I/O error, dev sdb, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2
[13434.846556] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command
[13434.854592] xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
[13434.862553] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
A dependency on this feature was recently introduced:
x86_64-linux-ld: vmlinux.o: in function `tc358768_bridge_pre_enable':
tc358768.c:(.text+0xbe3dae): undefined reference to `drm_display_mode_to_videomode'
When creating ceq_0 during probing irdma, cqp.sc_cqp will be sent as a
cqp_request to cqp->sc_cqp.sq_ring. If the request is pending when
removing the irdma driver or unplugging its aux device, cqp.sc_cqp will be
dereferenced as wrong struct in irdma_free_pending_cqp_request().
64k pages introduce the situation in this diagram when the HCA 4k page
size is being used:
+-------------------------------------------+ <--- 64k aligned VA
| |
| HCA 4k page |
| |
+-------------------------------------------+
| o |
| |
| o |
| |
| o |
+-------------------------------------------+
| |
| HCA 4k page |
| |
+-------------------------------------------+ <--- Live HCA page
|OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO| <--- offset
| | <--- VA
| MR data |
+-------------------------------------------+
| |
| HCA 4k page |
| |
+-------------------------------------------+
| o |
| |
| o |
| |
| o |
+-------------------------------------------+
| |
| HCA 4k page |
| |
+-------------------------------------------+
The VA addresses are coming from rdma-core in this diagram can be
arbitrary, but for 64k pages, the VA may be offset by some number of HCA
4k pages and followed by some number of HCA 4k pages.
The current iterator doesn't account for either the preceding 4k pages or
the following 4k pages.
Fix the issue by extending the ib_block_iter to contain the number of DMA
pages like comment [1] says and by using __sg_advance to start the
iterator at the first live HCA page.
The changes are contained in a parallel set of iterator start and next
functions that are umem aware and specific to umem since there is one user
of the rdma_for_each_block() without umem.
These two fixes prevents the extra pages before and after the user MR
data.
Fix the preceding pages by using the __sq_advance field to start at the
first 4k page containing MR data.
Fix the following pages by saving the number of pgsz blocks in the
iterator state and downcounting on each next.
This fix allows for the elimination of the small page crutch noted in the
Fixes.
Fixes: 10c75ccb54e4 ("RDMA/umem: Prevent small pages from being returned by ib_umem_find_best_pgsz()") Link: https://lore.kernel.org/r/20231129202143.1434-2-shiraz.saleem@intel.com Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When wm_adsp_buffer_read() fails, we should free buf->regions.
Otherwise, the callers of wm_adsp_buffer_populate() will
directly free buf on failure, which makes buf->regions a leaked
memory.
Fixes: a792af69b08f ("ASoC: wm_adsp: Refactor compress stream initialisation") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20231204074158.12026-1-dinghao.liu@zju.edu.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The multiplier is already promoted to unsigned long, however the
frequency calculations done when using level indexing mode doesn't
use the multiplier computed. It instead hardcodes the multiplier
value of 1000 at all the usage sites.
Clean that up by assigning the multiplier value of 1000 when using
the perf level indexing mode and update the frequency calculations to
use the multiplier instead. It should fix the possible frequency
truncation for all the values greater than or equal to 4GHz on 64-bit
machines.
Fix the possible frequency truncation for all values equal to or greater
4GHz on 64bit machines by updating the multiplier 'mult_factor' to
'unsigned long' type. It is also possible that the multiplier itself can
be greater than or equal to 2^32. So we need to also fix the equation
computing the value of the multiplier.
Fixes: a9e3fbfaa0ff ("firmware: arm_scmi: add initial support for performance protocol") Reported-by: Sibi Sankar <quic_sibis@quicinc.com> Closes: https://lore.kernel.org/all/20231129065748.19871-3-quic_sibis@quicinc.com/ Cc: Cristian Marussi <cristian.marussi@arm.com> Link: https://lore.kernel.org/r/20231130204343.503076-1-sudeep.holla@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to other protocol ops, it's useful for an scmi module driver to get
some generic information of a performance domain. Therefore, let's add a
new callback to provide this information. The information is currently
limited to the name of the performance domain and whether the set-level
operation is supported, although this can easily be extended if we find the
need for it.
Similar to other protocol ops, it's useful for an scmi module driver to get
the number of supported performance domains, hence let's make this
available by adding a new perf protocol callback. Note that, a user is
being added from subsequent changes.
The -1 value for active_decimator[dai_id] is considered as "not set",
but at probe the table is initialized a 0, this prevents enabling the
DEC0 Mixer since it will be considered as already set.
Initialize the table entries as -1 to fix tx_macro_tx_mixer_put().
"If an error occurs while obtaining the meter reading or if the value
is not available then an Integer with all bits set is returned"
Since the "integer" is 32 bits in case of the ACPI power meter,
userspace will get a power reading of 2^32 * 1000 miliwatts (~4.29 MW)
in case of such an error. This was discovered due to a lm_sensors
bugreport (https://github.com/lm-sensors/lm-sensors/issues/460).
Fix this by returning -ENODATA instead.
Tested-by: <urbinek@gmail.com> Fixes: de584afa5e18 ("hwmon driver for ACPI 4.0 power meters") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20231124182747.13956-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LED ACT which is included from bcm2711-rpi-4-b doesn't exists
on the Raspberry Pi 400. So the bcm2711-rpi-400.dts tries to
use the delete-node directive in order to remove the complete
node. Unfortunately the usage get broken in commit 1156e3a78bcc
("ARM: dts: bcm283x: Move ACT LED into separate dtsi")
and now ACT and PWR LED using the same GPIO and this prevent
probing of led-gpios on Raspberry Pi 400:
leds-gpio: probe of leds failed with error -16
So fix the delete-node directive.
Fixes: 1156e3a78bcc ("ARM: dts: bcm283x: Move ACT LED into separate dtsi") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/20231118124252.14838-3-wahrenst@gmx.net Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A regression was introduced in the Skov specific i.MX6 flavor
reve-mi1010ait-1cp1 device tree causing the external ethernet controller
to not being selected as the clock source for the i.MX6 ethernet MAC,
resulting in a none functional ethernet interface. The root cause is
that the ethernet clock selection is now part of the clocks node, which
is overwritten in the specific device tree and wasn't updated to contain
these ethernet clocks.
When removing the irdma driver or unplugging its aux device, the ccq
queue is released before destorying the cqp_cmpl_wq queue.
But in the window, there may still be completion events for wqes. That
will cause a UAF in irdma_sc_ccq_get_cqe_info().
As we chain the WR during write request: memory registration,
rdma write, local invalidate, if only the last WR fail to send due
to send queue overrun, the server can send back the reply, while
client mark the req->in_use to false in case of error in rtrs_clt_req
when error out from rtrs_post_rdma_write_sg.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-8-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For each write request, we need Request, Response Memory Registration,
Local Invalidate.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-7-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Destroying path files may lead to the freeing of rdma_stats. This creates
the following race.
An IO is in-flight, or has just passed the session state check in
process_read/process_write. The close_work gets triggered and the function
rtrs_srv_close_work() starts and does destroy path which frees the
rdma_stats. After this the function process_read/process_write resumes and
tries to update the stats through the function rtrs_srv_update_rdma_stats
This commit solves the problem by moving the destroy path function to a
later point. This point makes sure any inflights are completed. This is
done by qp drain, and waiting for all in-flights through ops_id.
Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality") Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Santosh Kumar Pradhan <santosh.pradhan@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-6-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since srv_mr->iu is allocated and used only when always_invalidate is
true, free it only when always_invalidate is true.
Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality") Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-5-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While processing info request, it could so happen that the srv_path goes
to CLOSING state, cause of any of the error events from RDMA. That state
change should be picked up while trying to change the state in
process_info_req, by checking the return value. In case the state change
call in process_info_req fails, we fail the processing.
We should also check the return value for rtrs_srv_path_up, since it
sends a link event to the client above, and the client can fail for any
reason.
Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality") Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-4-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we start hb too early, it will confuse server side to close
the session.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-3-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On i.MX8MP, when the TERE and FSD_MSTR enabled before configuring
the word width, there will be no frame sync clock issue, because
old word width impact the generation of frame sync.
TERE enabled earlier only for i.MX8MP case for the hardware limitation,
So need to disable FSD_MSTR before configuring word width, then enable
FSD_MSTR bit for this specific case.
Expand the reg size for the vdec node to include cache/performance
registers the rkvdec driver writes to. Also add missing clocks to the
related power-domain.
Fixes: cbd7214402ec ("arm64: dts: rockchip: Define the rockchip Video Decoder node on rk3399") Signed-off-by: Alex Bee <knaerzche@gmail.com> Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Link: https://lore.kernel.org/r/20231105233630.3927502-10-jonas@kwiboo.se Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, there is no wait for the QP suspend to complete on a modify
to SQD state. Add a wait, after the modify to SQD state, for the Suspend
Complete AE. While we are at it, update the suspend timeout value in
irdma_prep_tc_change to use IRDMA_EVENT_TIMEOUT_MS too.
projects / thirdparty / kernel / stable.git / log
