The session resources are used by FW and driver when session is offloaded,
once session is uploaded these resources are not used. The lock is not
required as these fields won't be used any longer. The offload and upload
calls are sequential, hence lock is not required.
sk->sk_rcvbuf in __sock_queue_rcv_skb() and __sk_receive_skb() can be
changed by other threads. Mark this as benign using READ_ONCE().
This patch is aimed at reducing the number of benign races reported by
KCSAN in order to focus future debugging effort on harmful races.
Signed-off-by: linke li <lilinke99@qq.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running kernel-doc on ieee80211_i.h flagged the following:
net/mac80211/ieee80211_i.h:145: warning: expecting prototype for enum ieee80211_corrupt_data_flags. Prototype was for enum ieee80211_bss_corrupt_data_flags instead
net/mac80211/ieee80211_i.h:162: warning: expecting prototype for enum ieee80211_valid_data_flags. Prototype was for enum ieee80211_bss_valid_data_flags instead
In punch_hole(), when the offset lies in the final block for a given
height, there is no hole to punch, but the maximum size check fails to
detect that. Consequently, punch_hole() will try to punch a hole beyond
the end of the metadata and fail. Fix the maximum size check.
Signed-off-by: Andrew Price <anprice@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Typically when an out of resource CQE status is detected, the
lpfc_ramp_down_queue_handler() logic is called to help reduce I/O load by
reducing an sdev's queue_depth.
However, the current lpfc_rampdown_queue_depth() logic does not help reduce
queue_depth. num_cmd_success is never updated and is always zero, which
means new_queue_depth will always be set to sdev->queue_depth. So,
new_queue_depth = sdev->queue_depth - new_queue_depth always sets
new_queue_depth to zero. And, scsi_change_queue_depth(sdev, 0) is
essentially a no-op.
Change the lpfc_ramp_down_queue_handler() logic to set new_queue_depth
equal to sdev->queue_depth subtracted from number of times num_rsrc_err was
incremented. If num_rsrc_err is >= sdev->queue_depth, then set
new_queue_depth equal to 1. Eventually, the frequency of Good_Status
frames will signal SCSI upper layer to auto increase the queue_depth back
to the driver default of 64 via scsi_handle_queue_ramp_up().
vgic_v2_parse_attr() is responsible for finding the vCPU that matches
the user-provided CPUID, which (of course) may not be valid. If the ID
is invalid, kvm_get_vcpu_by_id() returns NULL, which isn't handled
gracefully.
Similar to the GICv3 uaccess flow, check that kvm_get_vcpu_by_id()
actually returns something and fail the ioctl if not.
Cc: stable@vger.kernel.org Fixes: 7d450e282171 ("KVM: arm/arm64: vgic-new: Add userland access to VGIC dist registers") Reported-by: Alexander Potapenko <glider@google.com> Tested-by: Alexander Potapenko <glider@google.com> Reviewed-by: Alexander Potapenko <glider@google.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20240424173959.3776798-2-oliver.upton@linux.dev Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Sasha Levin <sashal@kernel.org>
When parsing a GICv2 attribute that contains a cpuid, handle this
as the vcpu_id, not a vcpu_idx, as userspace cannot really know
the mapping between the two. For this, use kvm_get_vcpu_by_id()
instead of kvm_get_vcpu().
Take this opportunity to get rid of the pointless check against
online_vcpus, which doesn't make much sense either, and switch
to FIELD_GET as a way to extract the vcpu_id.
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230927090911.3355209-5-maz@kernel.org Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Stable-dep-of: 6ddb4f372fc6 ("KVM: arm64: vgic-v2: Check for non-NULL vCPU in vgic_v2_parse_attr()") Signed-off-by: Sasha Levin <sashal@kernel.org>
While PLL CPUX clock rate change when CPU is running from it works in
vast majority of cases, now and then it causes instability. This leads
to system crashes and other undefined behaviour. After a lot of testing
(30+ hours) while also doing a lot of frequency switches, we can't
observe any instability issues anymore when doing reparenting to stable
clock like 24 MHz oscillator.
GRO-GSO path is supposed to be transparent and as such L3 flush checks are
relevant to all UDP flows merging in GRO. This patch uses the same logic
and code from tcp_gro_receive, terminating merge if flush is non zero.
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.") Signed-off-by: Richard Gobert <richardbgobert@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SKB_GSO_FRAGLIST skbs must not be linearized, otherwise they become
invalid. Return NULL if such an skb is passed to skb_copy or
skb_copy_expand, in order to prevent a crash on a potential later
call to skb_gso_segment.
Fixes: 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling skb_copy on a SKB_GSO_FRAGLIST skb is not valid, since it returns
an invalid linearized skb. This code only needs to change the ethernet
header, so pskb_copy is the right function to call here.
Fixes: 6db6f0eae605 ("bridge: multicast to unicast") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The selftest for the driver sends a dummy packet and checks if the
packet will be received properly as it should be. The regular TX path
and the selftest can use the same network queue so locking is required
and was missing in the selftest path. This was addressed in the commit
cited below.
Unfortunately locking the TX queue requires BH to be disabled which is
not the case in selftest path which is invoked in process context.
Lockdep should be complaining about this.
Use __netif_tx_lock_bh() for TX queue locking.
Fixes: c650e04898072 ("cxgb4: Fix race between loopback and normal Tx path") Reported-by: "John B. Wyatt IV" <jwyatt@redhat.com> Closes: https://lore.kernel.org/all/Zic0ot5aGgR-V4Ks@thinkpad2021/ Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20240429091147.YWAaal4v@linutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Amlogic sound cards do create a lot of pcm interfaces, possibly more than
8. Some pcm interfaces are internal (like DPCM backends and c2c) and not
exposed to userspace.
Those interfaces still increase the number passed to snd_find_free_minor(),
which eventually exceeds 8 causing -EBUSY error on card registration if
CONFIG_SND_DYNAMIC_MINORS=n and the interface is exposed to userspace.
select CONFIG_SND_DYNAMIC_MINORS for Amlogic cards to avoid the problem.
In qede_flow_spec_to_rule(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced qede_flow_spec_to_rule(),
and this call to qede_parse_flow_attr(), it looks
like it just duplicated how it was already used.
Only compile tested.
Fixes: 37c5d3efd7f8 ("qede: use ethtool_rx_flow_rule() to remove duplicated parser code") Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In qede_add_tc_flower_fltr(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced these functions.
Only compile tested.
Fixes: 2ce9c93eaca6 ("qede: Ingress tc flower offload (drop action) support.") Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fcee2065a178 ("net: qede: use return from qede_parse_flow_attr() for flower") Signed-off-by: Sasha Levin <sashal@kernel.org>
The return-address (RA) register r14 is specified as volatile in the
s390x ELF ABI [1]. Nevertheless proper CFI directives must be provided
for an unwinder to restore the return address, if the RA register
value is changed from its value at function entry, as it is the case.
NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner
protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls
skb_mac_gso_segment() to invoke inner protocol GSO handlers.
nsh_gso_segment() does the following for the original skb before
calling skb_mac_gso_segment()
1. reset skb->network_header
2. save the original skb->{mac_heaeder,mac_len} in a local variable
3. pull the NSH header
4. resets skb->mac_header
5. set up skb->mac_len and skb->protocol for the inner protocol.
and does the following for the segmented skb
6. set ntohs(ETH_P_NSH) to skb->protocol
7. push the NSH header
8. restore skb->mac_header
9. set skb->mac_header + mac_len to skb->network_header
10. restore skb->mac_len
There are two problems in 6-7 and 8-9.
(a)
After 6 & 7, skb->data points to the NSH header, so the outer header
(ETH_P_8021AD in this case) is stripped when skb is sent out of netdev.
Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH),
skb_pull() in the first nsh_gso_segment() will make skb->data point
to the middle of the outer NSH or Ethernet header because the Ethernet
header is not pulled by the second nsh_gso_segment().
(b)
While restoring skb->{mac_header,network_header} in 8 & 9,
nsh_gso_segment() does not assume that the data in the linear
buffer is shifted.
However, udp6_ufo_fragment() could shift the data and change
skb->mac_header accordingly as demonstrated by syzbot.
If this happens, even the restored skb->mac_header points to
the middle of the outer header.
It seems nsh_gso_segment() has never worked with outer headers so far.
At the end of nsh_gso_segment(), the outer header must be restored for
the segmented skb, instead of the NSH header.
To do that, let's calculate the outer header position relatively from
the inner header and set skb->{data,mac_header,protocol} properly.
We try to access count + 1 byte from userspace with memdup_user(buffer,
count + 1). However, the userspace only provides buffer of count bytes and
only these count bytes are verified to be okay to access. To ensure the
copied buffer is NUL terminated, we use memdup_user_nul instead.
Fixes: 3a2eb515d136 ("octeontx2-af: Fix an off by one in rvu_dbg_qsize_write()") Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com> Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-6-f1f1b53a10f4@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from
userspace to that buffer. Later, we use sscanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
The MT6360 regulator binding, the example in the MT6360 mfd binding, and
the devicetree users of those bindings are rightfully declaring MT6360
regulator subnodes with non-capital names, and luckily without using the
deprecated regulator-compatible property.
With this driver declaring capitalized BUCKx/LDOx as of_match string for
the node names, obviously no regulator gets probed: fix that by changing
the MT6360_REGULATOR_DESC macro to add a "match" parameter which gets
assigned to the of_match.
Fixes: d321571d5e4c ("regulator: mt6360: Add support for MT6360 regulator") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://msgid.link/r/20240409144438.410060-1-angelogioacchino.delregno@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we fail to allocate propname buffer, we need to drop the reference
count we just took. Because the pinctrl_dt_free_maps() includes the
droping operation, here we call it directly.
syzkaller reported a warning [0] triggered while destroying immature
netns.
rpc_proc_register() was called in init_nfs_fs(), but its error
has been ignored since at least the initial commit 1da177e4c3f4
("Linux-2.6.12-rc2").
Recently, commit d47151b79e32 ("nfs: expose /proc/net/sunrpc/nfs
in net namespaces") converted the procfs to per-netns and made
the problem more visible.
Even when rpc_proc_register() fails, nfs_net_init() could succeed,
and thus nfs_net_exit() will be called while destroying the netns.
Then, remove_proc_entry() will be called for non-existing proc
directory and trigger the warning below.
Let's handle the error of rpc_proc_register() properly in nfs_net_init().
Now that we're exposing the rpc stats on a per-network namespace basis,
move this struct into struct nfs_net and use that to make sure only the
per-network namespace stats are exposed.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be29f ("nfs: Handle error of rpc_proc_register() in nfs_net_init().") Signed-off-by: Sasha Levin <sashal@kernel.org>
We're using nfs mounts inside of containers in production and noticed
that the nfs stats are not exposed in /proc. This is a problem for us
as we use these stats for monitoring, and have to do this awkward bind
mount from the main host into the container in order to get to these
states.
Add the rpc_proc_register call to the pernet operations entry and exit
points so these stats can be exposed inside of network namespaces.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be29f ("nfs: Handle error of rpc_proc_register() in nfs_net_init().") Signed-off-by: Sasha Levin <sashal@kernel.org>
We want to be able to have our rpc stats handled in a per network
namespace manner, so add an option to rpc_create_args to specify a
different rpc_stats struct instead of using the one on the rpc_program.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be29f ("nfs: Handle error of rpc_proc_register() in nfs_net_init().") Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a misinterpretation of some of the PIN_CONFIG_* options in this
driver library. PIN_CONFIG_OUTPUT_ENABLE should refer to a buffer or
switch in the output direction of the electrical path. The MediaTek
hardware does not have such a thing. The driver incorrectly maps this
option to the GPIO function's direction.
Likewise, PIN_CONFIG_INPUT_ENABLE should refer to a buffer or switch in
the input direction. The hardware does have such a mechanism, and is
mapped to the IES bit. The driver however sets the direction in addition
to the IES bit, which is incorrect. On readback, the IES bit isn't even
considered.
Ironically, the driver does not support readback for PIN_CONFIG_OUTPUT,
while its readback of PIN_CONFIG_{INPUT,OUTPUT}_ENABLE is what it should
be doing for PIN_CONFIG_OUTPUT.
Rework support for these three options, so that PIN_CONFIG_OUTPUT_ENABLE
is completely removed, PIN_CONFIG_INPUT_ENABLE is only linked to the IES
bit, and PIN_CONFIG_OUTPUT is linked to the GPIO function's direction
and output level.
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20240327091336.3434141-3-wenst@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the generic pin config library, readback of some options are handled
differently compared to the setting of those options: the argument value
is used to convey enable/disable of an option in the set path, but
success or -EINVAL is used to convey if an option is enabled or disabled
in the debugfs readback path.
PIN_CONFIG_INPUT_SCHMITT_ENABLE is one such option. Fix the readback of
the option in the mediatek-paris library, so that the debugfs dump is
not showing "input schmitt enabled" for pins that don't have it enabled.
The current code deals with optional features by testing for the
function pointers and returning -ENOTSUPP if it is not valid. This is
done for multiple pin config settings and results in the code that
handles the supporting cases to get indented by one level. This is
aggrevated by the fact that some features require another level of
conditionals.
Instead of assigning the same error code in all unsupported optional
feature cases, simply have that error code as the default, and break
out of the switch/case block whenever a feature is unsupported, or an
error is returned. This reduces indentation by one level for the useful
code.
Also replace the goto statements with break statements. The result is
the same, as the gotos simply exit the switch/case block, which can
also be achieved with a break statement. With the latter the intent
is clear and easier to understand.
The "pctldev" struct is allocated in devm_pinctrl_register_and_init().
It's a devm_ managed pointer that is freed by devm_pinctrl_dev_release(),
so freeing it in pinctrl_enable() will lead to a double free.
The devm_pinctrl_dev_release() function frees the pindescs and destroys
the mutex as well.
The register offset to disable the internal pull-down of GPIOR~T is 0x630
instead of 0x620, as specified in the Ast2600 datasheet v15
The datasheet can download from the official Aspeed website.
Fixes: 15711ba6ff19 ("pinctrl: aspeed-g6: Add AST2600 pinconf support") Reported-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Message-ID: <20240313092809.2596644-1-billy_tsai@aspeedtech.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the eeprom is not accessible, an nvmem device will be registered, the
read will fail, and the device will be torn down. If another driver
accesses the nvmem device after the teardown, it will reference
invalid memory.
Move the failure point before registering the nvmem device.
The DDR3 SPD data structure advertises the presence of a thermal
sensor on a DDR3 module in byte 32, bit 7. Let's use this information
to explicitly instantiate the thermal sensor I2C client instead of
having to rely on class-based I2C probing.
The temp sensor i2c address can be derived from the SPD i2c address,
so we can directly instantiate the device and don't have to probe
for it. If the temp sensor has been instantiated already by other
means (e.g. class-based auto-detection), then the busy-check in
i2c_new_client_device will detect this.
Note: Thermal sensors on DDR4 DIMM's are instantiated from the
ee1004 driver.
When using nvmem layouts it is possible devm_nvmem_register returns
-EPROBE_DEFER, resulting in an 'empty' in
/sys/kernel/debug/devices_deferred. Use dev_err_probe for providing
additional information.
This reverts commit 22a9d9585812 ("dmaengine: pl330: issue_pending waits
until WFP state") as it seems to cause regression in pl330 driver.
Note the issue now exists in mainline so a fix to be done.
According to DMA-330 errata notice[1] 71930, DMAKILL
cannot clear internal signal, named pipeline_req_active.
it makes that pl330 would wait forever in WFP state
although dma already send dma request if pl330 gets
dma request before entering WFP state.
The errata suggests that polling until entering WFP state
as workaround and then peripherals allows to issue dma request.
riscv uses the value of TSK_STACK_CANARY to set
stack-protector-guard-offset. With GCC_PLUGIN_RANDSTRUCT enabled, that
value is non-deterministic, and with riscv:allmodconfig often results
in build errors such as
cc1: error: '8120' is not a valid offset in '-mstack-protector-guard-offset='
Enable STACKPROTECTOR_PER_TASK only if GCC_PLUGIN_RANDSTRUCT is disabled
to fix the problem.
If "udp_cmsg_send()" returned 0 (i.e. only UDP cmsg),
"connected" should not be set to 0. Otherwise it stops
the connected socket from using the cached route.
The flag I2C_HID_READ_PENDING is used to serialize I2C operations.
However, this is not necessary, because I2C core already has its own
locking for that.
More importantly, this flag can cause a lock-up: if the flag is set in
i2c_hid_xfer() and an interrupt happens, the interrupt handler
(i2c_hid_irq) will check this flag and return immediately without doing
anything, then the interrupt handler will be invoked again in an
infinite loop.
Since interrupt handler is an RT task, it takes over the CPU and the
flag-clearing task never gets scheduled, thus we have a lock-up.
Delete this unnecessary flag.
Reported-and-tested-by: Eva Kurchatova <nyandarknessgirl@gmail.com> Closes: https://lore.kernel.org/r/CA+eeCSPUDpUg76ZO8dszSbAGn+UHjcyv8F1J-CUPVARAzEtW9w@mail.gmail.com Fixes: 4a200c3b9a40 ("HID: i2c-hid: introduce HID over i2c specification implementation") Cc: <stable@vger.kernel.org> Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Jiri Kosina <jkosina@suse.com>
[apply to v4.19 -> v5.15] Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Baruch reported an OOPS when using the designware controller as target
only. Target-only modes break the assumption of one transfer function
always being available. Fix this by always checking the pointer in
__i2c_transfer.
Reported-by: Baruch Siach <baruch@tkos.co.il> Closes: https://lore.kernel.org/r/4269631780e5ba789cf1ae391eec1b959def7d99.1712761976.git.baruch@tkos.co.il Fixes: 4b1acc43331d ("i2c: core changes for slave support")
[wsa: dropped the simplification in core-smbus to avoid theoretical regressions] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Sasha Levin <sashal@kernel.org>
On NOMMU, userspace memory can come from anywhere in physical RAM. The
current definition of TASK_SIZE is wrong if any RAM exists above 4G,
causing spurious failures in the userspace access routines.
Fixes: 6bd33e1ece52 ("riscv: add nommu support") Fixes: c3f896dcf1e4 ("mm: switch the test_vmalloc module to use __vmalloc_node") Signed-off-by: Samuel Holland <samuel.holland@sifive.com> Reviewed-by: Jisheng Zhang <jszhang@kernel.org> Reviewed-by: Bo Gan <ganboing@gmail.com> Link: https://lore.kernel.org/r/20240227003630.3634533-2-samuel.holland@sifive.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-------------------------------------------------------------------
arch/riscv/kernel/crash_core.c: In function 'arch_crash_save_vmcoreinfo':
arch/riscv/kernel/crash_core.c:11:58: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'int' [-Wformat=]
11 | vmcoreinfo_append_str("NUMBER(VMALLOC_START)=0x%lx\n", VMALLOC_START);
| ~~^
| |
| long unsigned int
| %x
----------------------------------------------------------------------
This is because on riscv macro VMALLOC_START has different type when
CONFIG_MMU is set or unset.
When iDMA 64-bit device is powered off, the IRQ status register
is all 1:s. This is never happen in real case and signalling that
the device is simply powered off. Don't try to serve interrupts
that are not ours.
When building with 'make W=1', clang notices that the computed register
values are never actually written back but instead the wrong variable
is set:
drivers/dma/owl-dma.c:244:6: error: variable 'regval' set but not used [-Werror,-Wunused-but-set-variable]
244 | u32 regval;
| ^
drivers/dma/owl-dma.c:268:6: error: variable 'regval' set but not used [-Werror,-Wunused-but-set-variable]
268 | u32 regval;
| ^
Eric Dumazet reported a use-after-free related to the per-netns ehash
series. [0]
When we create a TCP socket from userspace, the socket always holds a
refcnt of the netns. This guarantees that a reqsk timer is always fired
before netns dismantle. Each reqsk has a refcnt of its listener, so the
listener is not freed before the reqsk, and the net is not freed before
the listener as well.
OTOH, when in-kernel users create a TCP socket, it might not hold a refcnt
of its netns. Thus, a reqsk timer can be fired after the netns dismantle
and access freed per-netns ehash.
To avoid the use-after-free, we need to clean up TCP_NEW_SYN_RECV sockets
in inet_twsk_purge() if the netns uses a per-netns ehash.
BUG: KASAN: use-after-free in tcp_or_dccp_get_hashinfo
include/net/inet_hashtables.h:181 [inline]
BUG: KASAN: use-after-free in reqsk_queue_unlink+0x320/0x350
net/ipv4/inet_connection_sock.c:913
Read of size 8 at addr ffff88807545bd80 by task syz-executor.2/8301
I ran into a randconfig build failure with UBSAN using gcc-13.2:
arm-linux-gnueabi-ld: error: unplaced orphan section `.bss..Lubsan_data31' from `drivers/mtd/nand/raw/diskonchip.o'
I'm not entirely sure what is going on here, but I suspect this has something
to do with the check for the end of the doc_locations[] array that contains
an (unsigned long)0xffffffff element, which is compared against the signed
(int)0xffffffff. If this is the case, we should get a runtime check for
undefined behavior, but we instead get an unexpected build-time error.
I would have expected this to work fine on 32-bit architectures despite the
signed integer overflow, though on 64-bit architectures this likely won't
ever work.
Changing the contition to instead check for the size of the array makes the
code safe everywhere and avoids the ubsan check that leads to the link
error. The loop code goes back to before 2.6.12.
If stack_depot_save_flags() allocates memory it always drops
__GFP_NOLOCKDEP flag. So when KASAN tries to track __GFP_NOLOCKDEP
allocation we may end up with lockdep splat like bellow:
======================================================
WARNING: possible circular locking dependency detected
6.9.0-rc3+ #49 Not tainted
------------------------------------------------------
kswapd0/149 is trying to acquire lock: ffff88811346a920
(&xfs_nondir_ilock_class){++++}-{4:4}, at: xfs_reclaim_inode+0x3ac/0x590
[xfs]
but task is already holding lock: ffffffff8bb33100 (fs_reclaim){+.+.}-{0:0}, at:
balance_pgdat+0x5d9/0xad0
b44_free_rings() accesses b44::rx_buffers (and ::tx_buffers)
unconditionally, but b44::rx_buffers is only valid when the
device is up (they get allocated in b44_open(), and deallocated
again in b44_close()), any other time these are just a NULL pointers.
So if you try to change the pause params while the network interface
is disabled/administratively down, everything explodes (which likely
netifd tries to do).
Link: https://github.com/openwrt/openwrt/issues/13789 Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2) Cc: stable@vger.kernel.org Reported-by: Peter Münster <pm@a16n.net> Suggested-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Vaclav Svoboda <svoboda@neng.cz> Tested-by: Peter Münster <pm@a16n.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Peter Münster <pm@a16n.net> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/87y192oolj.fsf@a16n.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error handling path in its_vpe_irq_domain_alloc() causes a double free
when its_vpe_init() fails after successfully allocating at least one
interrupt. This happens because its_vpe_irq_domain_free() frees the
interrupts along with the area bitmap and the vprop_page and
its_vpe_irq_domain_alloc() subsequently frees the area bitmap and the
vprop_page again.
Fix this by unconditionally invoking its_vpe_irq_domain_free() which
handles all cases correctly and by removing the bitmap/vprop_page freeing
from its_vpe_irq_domain_alloc().
This avoids a potential conflict with firmwares with the newer
HDP flush mechanism.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Q7_THRM# pin is connected to a diode on the module which is used
as a level shifter, and the pin have a pull-down enabled by
default. We need to configure it to internal pull-up, other-
wise whenever the pin is configured as INPUT and we try to
control it externally the value will always remain zero.
Rename x86's to CPU_MITIGATIONS, define it in generic code, and force it
on for all architectures exception x86. A recent commit to turn
mitigations off by default if SPECULATION_MITIGATIONS=n kinda sorta
missed that "cpu_mitigations" is completely generic, whereas
SPECULATION_MITIGATIONS is x86-specific.
Rename x86's SPECULATIVE_MITIGATIONS instead of keeping both and have it
select CPU_MITIGATIONS, as having two configs for the same thing is
unnecessary and confusing. This will also allow x86 to use the knob to
manage mitigations that aren't strictly related to speculative
execution.
Use another Kconfig to communicate to common code that CPU_MITIGATIONS
is already defined instead of having x86's menu depend on the common
CPU_MITIGATIONS. This allows keeping a single point of contact for all
of x86's mitigations, and it's not clear that other architectures *want*
to allow disabling mitigations at compile-time.
Fixes: f337a6a21e2f ("x86/cpu: Actually turn off mitigations by default for SPECULATION_MITIGATIONS=n") Closes: https://lkml.kernel.org/r/20240413115324.53303a68%40canb.auug.org.au Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: Michael Ellerman <mpe@ellerman.id.au> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: Josh Poimboeuf <jpoimboe@kernel.org> Acked-by: Borislav Petkov (AMD) <bp@alien8.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240420000556.2645001-2-seanjc@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bytes 40-65535 of 65536 are uninitialized
Memory access of size 65536 starts at ffff888045a40000
This happens, because we're copying a 'struct btrfs_data_container' back
to user-space. This btrfs_data_container is allocated in
'init_data_container()' via kvmalloc(), which does not zero-fill the
memory.
Fix this by using kvzalloc() which zeroes out the memory on allocation.
CC: stable@vger.kernel.org # 4.14+ Reported-by: <syzbot+510a1abbb8116eeb341d@syzkaller.appspotmail.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Johannes Thumshirn <Johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the support ID(0x0bda, 0x4853) to usb_device_id table for
Realtek RTL8852BE.
Without this change the device utilizes an obsolete version of
the firmware that is encoded in it rather than the updated Realtek
firmware and config files from the firmware directory. The latter
files implement many new features.
After an innocuous optimization change in LLVM main (19.0.0), x86_64
allmodconfig (which enables CONFIG_KCSAN / -fsanitize=thread) fails to
build due to the checks in check_copy_size():
In file included from net/bluetooth/sco.c:27:
In file included from include/linux/module.h:13:
In file included from include/linux/stat.h:19:
In file included from include/linux/time.h:60:
In file included from include/linux/time32.h:13:
In file included from include/linux/timex.h:67:
In file included from arch/x86/include/asm/timex.h:6:
In file included from arch/x86/include/asm/tsc.h:10:
In file included from arch/x86/include/asm/msr.h:15:
In file included from include/linux/percpu.h:7:
In file included from include/linux/smp.h:118:
include/linux/thread_info.h:244:4: error: call to '__bad_copy_from'
declared with 'error' attribute: copy source size is too small
244 | __bad_copy_from();
| ^
The same exact error occurs in l2cap_sock.c. The copy_to_user()
statements that are failing come from l2cap_sock_getsockopt_old() and
sco_sock_getsockopt_old(). This does not occur with GCC with or without
KCSAN or Clang without KCSAN enabled.
len is defined as an 'int' because it is assigned from
'__user int *optlen'. However, it is clamped against the result of
sizeof(), which has a type of 'size_t' ('unsigned long' for 64-bit
platforms). This is done with min_t() because min() requires compatible
types, which results in both len and the result of sizeof() being casted
to 'unsigned int', meaning len changes signs and the result of sizeof()
is truncated. From there, len is passed to copy_to_user(), which has a
third parameter type of 'unsigned long', so it is widened and changes
signs again. This excessive casting in combination with the KCSAN
instrumentation causes LLVM to fail to eliminate the __bad_copy_from()
call, failing the build.
The official recommendation from LLVM developers is to consistently use
long types for all size variables to avoid the unnecessary casting in
the first place. Change the type of len to size_t in both
l2cap_sock_getsockopt_old() and sco_sock_getsockopt_old(). This clears
up the error while allowing min_t() to be replaced with min(), resulting
in simpler code with no casts and fewer implicit conversions. While len
is a different type than optlen now, it should result in no functional
change because the result of sizeof() will clamp all values of optlen in
the same manner as before.
Convert simple snprintf to the more secure scnprintf with size of
PAGE_SIZE.
Add condition checking if we are exceeding PAGE_SIZE and exit early from
loop. Also add at the end a warning that we exceeded PAGE_SIZE and that
stats is disabled.
Return -EFBIG in the case where we don't have enough space to write the
full transition table.
Also document in the ABI that this function can return -EFBIG error.
Link: https://lore.kernel.org/all/20231024183016.14648-2-ansuelsmth@gmail.com/ Cc: stable@vger.kernel.org Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218041 Fixes: e552bbaf5b98 ("PM / devfreq: Add sysfs node for representing frequency transition information.") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running endpoint security solutions like Sentinel1 that use perf-based
tracing heavily lead to this repeated dump complaining about dockerd.
The default value of 2048 is nowhere near not large enough.
Using the prior patch "tracing: show size of requested buffer", we get
"perf buffer not large enough, wanted 6644, have 6144", after repeated
up-sizing (I did 2/4/6/8K). With 8K, the problem doesn't occur at all,
so below is the trace for 6K.
I'm wondering if this value should be selectable at boot time, but this
is a good starting point.
Link: https://lkml.kernel.org/r/20210831043723.13481-2-robbat2@gentoo.org Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the perf buffer isn't large enough, provide a hint about how large it
needs to be for whatever is running.
Link: https://lkml.kernel.org/r/20210831043723.13481-1-robbat2@gentoo.org Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Fix a cmd->ent use after free due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process allocated a ent->idx but didn't set ent to cmd->ent_arr in
cmd_work_handler(). Fix it by moving the assignment of cmd->ent_arr into
the spin lock.
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
Provide wrapper functions for spin_[un]lock*(port->lock) invocations so
that the console mechanics can be applied later on at a single place and
does not require to copy the same logic all over the drivers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-2-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 54c4ec5f8c47 ("serial: mxs-auart: add spinlock around changing cts state") Signed-off-by: Sasha Levin <sashal@kernel.org>
The CPTS, by design, captures the messageType (Sync, Delay_Req, etc.)
field from the second nibble of the PTP header which is defined in the
PTPv2 (1588-2008) specification. In the PTPv1 (1588-2002) specification
the first two bytes of the PTP header are defined as the versionType
which is always 0x0001. This means that any PTPv1 packets that are
tagged for TX timestamping by the CPTS will have their messageType set
to 0x0 which corresponds to a Sync message type. This causes issues
when a PTPv1 stack is expecting a Delay_Req (messageType: 0x1)
timestamp that never appears.
Fix this by checking if the ptp_class of the timestamped TX packet is
PTP_CLASS_V1 and then matching the PTP sequence ID to the stored
sequence ID in the skb->cb data structure. If the sequence IDs match
and the packet is of type PTPv1 then there is a chance that the
messageType has been incorrectly stored by the CPTS so overwrite the
messageType stored by the CPTS with the messageType from the skb->cb
data structure. This allows the PTPv1 stack to receive TX timestamps
for Delay_Req packets which are necessary to lock onto a PTP Leader.
Signed-off-by: Jason Reeder <jreeder@ti.com> Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com> Tested-by: Ed Trexel <ed.trexel@hp.com> Fixes: f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver") Link: https://lore.kernel.org/r/20240424071626.32558-1-r-gunasekaran@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Same number of TCs doesn't imply that underlying TC configs are
same. The config could be different due to difference in number
of queues in each TC. Add utility function to determine if TC
configs are same.
Fixes: d5b33d024496 ("i40evf: add ndo_setup_tc callback to i40evf") Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com> Tested-by: Mineri Bhange <minerix.bhange@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240423182723.740401-4-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the MFS is set below the default (0x2600), a warning message is
reported like the following :
MFS for port 1 has been set below the default: 600
This message is a bit confusing as the number shown here (600) is in
fact an hexa number: 0x600 = 1536
Without any explicit "0x" prefix, this message is read like the MFS is
set to 600 bytes.
MFS, as per MTUs, are usually expressed in decimal base.
This commit reports both current and default MFS values in decimal
so it's less confusing for end-users.
A typical warning message looks like the following :
MFS for port 1 (1536) has been set below the default (9728)
Signed-off-by: Erwan Velu <e.velu@criteo.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Tony Brelinski <tony.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Fixes: 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set") Link: https://lore.kernel.org/r/20240423182723.740401-3-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Issue reported by customer during SRIOV testing, call trace:
When both i40e and the i40iw driver are loaded, a warning
in check_flush_dependency is being triggered. This seems
to be because of the i40e driver workqueue is allocated with
the WQ_MEM_RECLAIM flag, and the i40iw one is not.
Similar error was encountered on ice too and it was fixed by
removing the flag. Do the same for i40e too.
Fixes: d54725cd11a5 ("netfilter: nf_tables: support for multiple devices per netdev hook") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rehash delayed work is rescheduled with a delay if the number of
credits at end of the work is not negative as supposedly it means that
the migration ended. Otherwise, it is rescheduled immediately.
After "mlxsw: spectrum_acl_tcam: Fix possible use-after-free during
rehash" the above is no longer accurate as a non-negative number of
credits is no longer indicative of the migration being done. It can also
happen if the work encountered an error in which case the migration will
resume the next time the work is scheduled.
The significance of the above is that it is possible for the work to be
pending and associated with hints that were allocated when the migration
started. This leads to the hints being leaked [1] when the work is
canceled while pending as part of ACL region dismantle.
Fix by freeing the hints if hints are associated with a work that was
canceled while pending.
Blame the original commit since the reliance on not having a pending
work associated with hints is fragile.
Both the function that migrates all the chunks within a region and the
function that migrates all the entries within a chunk call
list_first_entry() on the respective lists without checking that the
lists are not empty. This is incorrect usage of the API, which leads to
the following warning [1].
Fix by returning if the lists are empty as there is nothing to migrate
in this case.
As previously explained, the rehash delayed work migrates filters from
one region to another. This is done by iterating over all chunks (all
the filters with the same priority) in the region and in each chunk
iterating over all the filters.
When the work runs out of credits it stores the current chunk and entry
as markers in the per-work context so that it would know where to resume
the migration from the next time the work is scheduled.
Upon error, the chunk marker is reset to NULL, but without resetting the
entry markers despite being relative to it. This can result in migration
being resumed from an entry that does not belong to the chunk being
migrated. In turn, this will eventually lead to a chunk being iterated
over as if it is an entry. Because of how the two structures happen to
be defined, this does not lead to KASAN splats, but to warnings such as
[1].
Fix by creating a helper that resets all the markers and call it from
all the places the currently only reset the chunk marker. For good
measures also call it when starting a completely new rehash. Add a
warning to avoid future cases.
The rehash delayed work migrates filters from one region to another.
This is done by iterating over all chunks (all the filters with the same
priority) in the region and in each chunk iterating over all the
filters.
If the migration fails, the code tries to migrate the filters back to
the old region. However, the rollback itself can also fail in which case
another migration will be erroneously performed. Besides the fact that
this ping pong is not a very good idea, it also creates a problem.
Each virtual chunk references two chunks: The currently used one
('vchunk->chunk') and a backup ('vchunk->chunk2'). During migration the
first holds the chunk we want to migrate filters to and the second holds
the chunk we are migrating filters from.
The code currently assumes - but does not verify - that the backup chunk
does not exist (NULL) if the currently used chunk does not reference the
target region. This assumption breaks when we are trying to rollback a
rollback, resulting in the backup chunk being overwritten and leaked
[1].
Fix by not rolling back a failed rollback and add a warning to avoid
future cases.
Fixes: 843500518509 ("mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Alexander Zubkov <green@qrator.net> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/d5edd4f4503934186ae5cfe268503b16345b4e0f.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the rare cases when the device resources are exhausted it is likely
that the rehash delayed work will fail. An error message will be printed
whenever this happens which can be overwhelming considering the fact
that the work is per-region and that there can be hundreds of regions.
Fix by rate limiting the error message.
Fixes: e5e7962ee5c2 ("mlxsw: spectrum_acl: Implement region migration according to hints") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Alexander Zubkov <green@qrator.net> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/c510763b2ebd25e7990d80183feff91cde593145.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rehash delayed work migrates filters from one region to another
according to the number of available credits.
The migrated from region is destroyed at the end of the work if the
number of credits is non-negative as the assumption is that this is
indicative of migration being complete. This assumption is incorrect as
a non-negative number of credits can also be the result of a failed
migration.
The destruction of a region that still has filters referencing it can
result in a use-after-free [1].
Fix by not destroying the region if migration failed.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
Read of size 8 at addr ffff8881735319e8 by task kworker/0:31/3858
The rule activity update delayed work periodically traverses the list of
configured rules and queries their activity from the device.
As part of this task it accesses the entry pointed by 'ventry->entry',
but this entry can be changed concurrently by the rehash delayed work,
leading to a use-after-free [1].
Fix by closing the race and perform the activity query under the
'vregion->lock' mutex.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
Read of size 8 at addr ffff8881054ed808 by task kworker/0:18/181
The purpose of the rehash delayed work is to reduce the number of masks
(eRPs) used by an ACL region as the eRP bank is a global and limited
resource.
This is done in three steps:
1. Creating a new set of masks and a new ACL region which will use the
new masks and to which the existing filters will be migrated to. The
new region is assigned to 'vregion->region' and the region from which
the filters are migrated from is assigned to 'vregion->region2'.
2. Migrating all the filters from the old region to the new region.
3. Destroying the old region and setting 'vregion->region2' to NULL.
Only the second steps is performed under the 'vregion->lock' mutex
although its comments says that among other things it "Protects
consistency of region, region2 pointers".
This is problematic as the first step can race with filter insertion
from user space that uses 'vregion->region', but under the mutex.
Fix by holding the mutex across the entirety of the delayed work and not
only during the second step.
Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Alexander Zubkov <green@qrator.net> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/1ec1d54edf2bad0a369e6b4fa030aba64e1f124b.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal
of ovs_ct_limit_exit, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit") Signed-off-by: Hyunwoo Kim <v4bel@theori.io> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Aaron Conole <aconole@redhat.com> Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed in the wild that pairs of consecutive packets would leave
the IPVS with the same wrong checksum, and the issue only went away when
disabling GSO.
IPVS needs to avoid computing the SCTP checksum when using GSO.
Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of gtp_dellink, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 94dc550a5062 ("gtp: fix an use-after-free in ipv4_pdp_find()") Signed-off-by: Hyunwoo Kim <v4bel@theori.io> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize overide.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path")
Fixes: f8ebb3ac881b ("net: usb: ax88179_178a: Fix packet receiving") Reported-by: shironeko <shironeko@tesaguri.club> Closes: https://lore.kernel.org/netdev/c110f41a0d2776b525930f213ca9715c@tesaguri.club/ Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jose Alonso <joalonsof@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240421193828.1966195-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 02b24941619f ("ipv4: use dst hint for ipv4 list receive") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20240421184326.1704930-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During module probe, regulator 'vin' and 'vdd-io' are used and enabled,
but the vdd-io regulator overwrites the 'vin' regulator pointer. During
remove, only the vdd-io is disabled, as the vin regulator pointer is not
available anymore. When regulator_put() is called during resource
cleanup a kernel warning is given, as the regulator is still enabled.
Store the two regulators in separate pointers and disable both the
regulators on module remove.
projects / thirdparty / kernel / stable.git / log
