According to the "GPIO Expander Map / Table" section of the J722S EVM
Schematic within the Evaluation Module Design Files package [0], the
GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled
down to select the Type-C interface. Since commit under Fixes claims to
enable the Type-C interface, update the property within "p05-hog" from
"output-high" to "output-low", thereby switching from the Type-A
interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
Cc: stable@vger.kernel.org Fixes: 485705df5d5f ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM") Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Link: https://lore.kernel.org/r/20250623100657.4082031-1-s-vadapalli@ti.com Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quote from the virtio specification chapter 4.2.2.2:
"For the device-specific configuration space, the driver MUST use 8 bit
wide accesses for 8 bit wide fields, 16 bit wide and aligned accesses
for 16 bit wide fields and 32 bit wide and aligned accesses for 32 and
64 bit wide fields."
Commit 34331d7beed7 ("smb: client: fix first command failure during
re-negotiation") addressed a race condition by updating lstrp before
entering negotiate state. However, this approach may have some unintended
side effects.
The lstrp field is documented as "when we got last response from this
server", and updating it before actually receiving a server response
could potentially affect other mechanisms that rely on this timestamp.
For example, the SMB echo detection logic also uses lstrp as a reference
point. In scenarios with frequent user operations during reconnect states,
the repeated calls to cifs_negotiate_protocol() might continuously
update lstrp, which could interfere with the echo detection timing.
Additionally, commit 266b5d02e14f ("smb: client: fix race condition in
negotiate timeout by using more precise timing") introduced a dedicated
neg_start field specifically for tracking negotiate start time. This
provides a more precise solution for the original race condition while
preserving the intended semantics of lstrp.
Since the race condition is now properly handled by the neg_start
mechanism, the lstrp update in cifs_negotiate_protocol() is no longer
necessary and can be safely removed.
Fixes: 266b5d02e14f ("smb: client: fix race condition in negotiate timeout by using more precise timing") Cc: stable@vger.kernel.org Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.org> Signed-off-by: Wang Zhaolong <wangzhaolong@huaweicloud.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UAC3 class segment descriptors need to be verified whether their sizes
match with the declared lengths and whether they fit with the
allocated buffer sizes, too. Otherwise malicious firmware may lead to
the unexpected OOB accesses.
Ring provided buffers are potentially only valid within the single
execution context in which they were acquired. io_uring deals with this
and invalidates them on retry. But on the networking side, if
MSG_WAITALL is set, or if the socket is of the streaming type and too
little was processed, then it will hang on to the buffer rather than
recycle or commit it. This is problematic for two reasons:
1) If someone unregisters the provided buffer ring before a later retry,
then the req->buf_list will no longer be valid.
2) If multiple sockers are using the same buffer group, then multiple
receives can consume the same memory. This can cause data corruption
in the application, as either receive could land in the same
userspace buffer.
Fix this by disallowing partial retries from pinning a provided buffer
across multiple executions, if ring provided buffers are used.
Cc: stable@vger.kernel.org Reported-by: pt x <superman.xpt@gmail.com> Fixes: c56e022c0a27 ("io_uring: add support for user mapped provided buffer ring") Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the allocated size exceeds UINT_MAX, then it's necessary to cast
the mr->nr_pages value to size_t to prevent it from overflowing. In
practice this isn't much of a concern as the required memory size will
have been validated upfront, and accounted to the user. And > 4GB sizes
will be necessary to make the lack of a cast a problem, which greatly
exceeds normal user locked_vm settings that are generally in the kb to
mb range. However, if root is used, then accounting isn't done, and
then it's possible to hit this issue.
zcrx areas can be quite large and need to be accounted and checked
against RLIMIT_MEMLOCK. In practise it shouldn't be a big issue as
the inteface already requires cap_net_admin.
__kernel_rwf_t is defined as int, the actual size of which is
implementation defined. It won't go well if some compiler / archs
ever defines it as i64, so replace it with __u32, hoping that
there is no one using i16 for it.
By inducing delays in the right places, Jann Horn created a reproducer for
a hard to hit UAF issue that became possible after VMAs were allowed to be
recycled by adding SLAB_TYPESAFE_BY_RCU to their cache.
Race description is borrowed from Jann's discovery report:
lock_vma_under_rcu() looks up a VMA locklessly with mas_walk() under
rcu_read_lock(). At that point, the VMA may be concurrently freed, and it
can be recycled by another process. vma_start_read() then increments the
vma->vm_refcnt (if it is in an acceptable range), and if this succeeds,
vma_start_read() can return a recycled VMA.
In this scenario where the VMA has been recycled, lock_vma_under_rcu()
will then detect the mismatching ->vm_mm pointer and drop the VMA through
vma_end_read(), which calls vma_refcount_put(). vma_refcount_put() drops
the refcount and then calls rcuwait_wake_up() using a copy of vma->vm_mm.
This is wrong: It implicitly assumes that the caller is keeping the VMA's
mm alive, but in this scenario the caller has no relation to the VMA's mm,
so the rcuwait_wake_up() can cause UAF.
The diagram depicting the race:
T1 T2 T3
== == ==
lock_vma_under_rcu
mas_walk
<VMA gets removed from mm>
mmap
<the same VMA is reallocated>
vma_start_read
__refcount_inc_not_zero_limited_acquire
munmap
__vma_enter_locked
refcount_add_not_zero
vma_end_read
vma_refcount_put
__refcount_dec_and_test
rcuwait_wait_event
<finish operation>
rcuwait_wake_up [UAF]
Note that rcuwait_wait_event() in T3 does not block because refcount was
already dropped by T1. At this point T3 can exit and free the mm causing
UAF in T1.
To avoid this we move vma->vm_mm verification into vma_start_read() and
grab vma->vm_mm to stabilize it before vma_refcount_put() operation.
As station, WCN7850 firmware requires pairwise key to be installed before
group key. Currently host does not care about this, so it is up to kernel
or userspace to decide which one will be installed first. In case above
requirement is not met, WCN7850 firmware's EAPOL station machine is messed
up, and finally connection fails [1].
Reorder key install for station interface in that case: this is done by
caching group key first; Later when pairwise key arrives, both can be
installed in required order.
1. In func configfs_composite_bind() -> composite_os_desc_req_prepare():
if kmalloc fails, the pointer cdev->os_desc_req will be freed but not
set to NULL. Then it will return a failure to the upper-level function.
2. in func configfs_composite_bind() -> composite_dev_cleanup():
it will checks whether cdev->os_desc_req is NULL. If it is not NULL, it
will attempt to use it.This will lead to a use-after-free issue.
BUG: KASAN: use-after-free in composite_dev_cleanup+0xf4/0x2c0
Read of size 8 at addr 0000004827837a00 by task init/1
CPU: 10 PID: 1 Comm: init Tainted: G O 5.10.97-oh #1
kasan_report+0x188/0x1cc
__asan_load8+0xb4/0xbc
composite_dev_cleanup+0xf4/0x2c0
configfs_composite_bind+0x210/0x7ac
udc_bind_to_driver+0xb4/0x1ec
usb_gadget_probe_driver+0xec/0x21c
gadget_dev_desc_UDC_store+0x264/0x27c
Currently, the battery timer is set up for all devices using hid-apple,
irrespective of whether they actually have a battery or not.
APPLE_RDESC_BATTERY is a quirk that indicates the device has a battery
and needs the battery timer. This patch checks for this quirk before
setting up the timer, ensuring that only devices with a battery will
have the timer set up.
Currently, the battery timer is set up for all devices using
hid-magicmouse, irrespective of whether they actually need it or not.
The current implementation requires the battery timer for Magic Mouse 2
and Magic Trackpad 2 when connected via USB only. Add checks to ensure
that the battery timer is only set up when they are connected via USB.
Testing by the syzbot fuzzer showed that the HID core gets a
shift-out-of-bounds exception when it tries to convert a 32-bit
quantity to a 0-bit quantity. Ideally this should never occur, but
there are buggy devices and some might have a report field with size
set to zero; we shouldn't reject the report or the device just because
of that.
Instead, harden the s32ton() routine so that it returns a reasonable
result instead of crashing when it is called with the number of bits
set to 0 -- the same as what snto32() does.
In hidg_bind(), if alloc_workqueue() fails after usb_assign_descriptors()
has successfully allocated the USB descriptors, the current error handling
does not call usb_free_all_descriptors() to free the allocated descriptors,
resulting in a memory leak.
Restructure the error handling by adding proper cleanup labels:
- fail_free_all: cleans up workqueue and descriptors
- fail_free_descs: cleans up descriptors only
- fail: original cleanup for earlier failures
This ensures that allocated resources are properly freed in reverse order
of their allocation, preventing the memory leak when alloc_workqueue() fails.
A malicious HID device with quirk APPLE_MAGIC_BACKLIGHT can trigger a NULL
pointer dereference whilst the power feature-report is toggled and sent to
the device in apple_magic_backlight_report_set(). The power feature-report
is expected to have two data fields, but if the descriptor declares one
field then accessing field[1] and dereferencing it in
apple_magic_backlight_report_set() becomes invalid
since field[1] will be NULL.
An example of a minimal descriptor which can cause the crash is something
like the following where the report with ID 3 (power report) only
references a single 1-byte field. When hid core parses the descriptor it
will encounter the final feature tag, allocate a hid_report (all members
of field[] will be zeroed out), create field structure and populate it,
increasing the maxfield to 1. The subsequent field[1] access and
dereference causes the crash.
Usage Page (Vendor Defined 0xFF00)
Usage (0x0F)
Collection (Application)
Report ID (1)
Usage (0x01)
Logical Minimum (0)
Logical Maximum (255)
Report Size (8)
Report Count (1)
Feature (Data,Var,Abs)
To fix this issue we should validate the number of fields that the
backlight and power reports have and if they do not have the required
number of fields then bail.
Fixes: 394ba612f941 ("HID: apple: Add support for magic keyboard backlight on T2 Macs") Cc: stable@vger.kernel.org Signed-off-by: Qasim Ijaz <qasdev00@gmail.com> Reviewed-by: Orlando Chamberlain <orlandoch.dev@gmail.com> Tested-by: Aditya Garg <gargaditya08@live.com> Link: https://patch.msgid.link/20250713233008.15131-1-qasdev00@gmail.com Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ti_csi2rx_start_dma() fails in ti_csi2rx_dma_callback(), the buffer is
marked done with VB2_BUF_STATE_ERROR but is not removed from the DMA queue.
This causes the same buffer to be retried in the next iteration, resulting
in a double list_del() and eventual list corruption.
Fix this by removing the buffer from the queue before calling
vb2_buffer_done() on error.
Fix NULL pointer crash in uvcg_framebased_make due to uninitialized color
matching descriptor for frame-based format which was added in
commit f5e7bdd34aca ("usb: gadget: uvc: Allow creating new color matching
descriptors") that added handling for uncompressed and mjpeg format.
Crash is seen when userspace configuration (via configfs) does not
explicitly define the color matching descriptor. If color_matching is not
found, config_group_find_item() returns NULL. The code then jumps to
out_put_cm, where it calls config_item_put(color_matching);. If
color_matching is NULL, this will dereference a null pointer, leading to a
crash.
Initialize color matching descriptor for frame-based format to prevent
NULL pointer crash by mirroring the handling done for uncompressed and
mjpeg formats.
After commit acd7ccb284b8 ("mm: shmem: add large folio support for
tmpfs"), we extend the 'huge=' option to allow any sized large folios for
tmpfs, which means tmpfs will allow getting a highest order hint based on
the size of write() and fallocate() paths, and then will try each
allowable large order.
However, when the i915 driver allocates shmem memory, it doesn't provide
hint information about the size of the large folio to be allocated,
resulting in the inability to allocate PMD-sized shmem, which in turn
affects GPU performance.
Patryk added:
: In my tests, the performance drop ranges from a few percent up to 13%
: in Unigine Superposition under heavy memory usage on the CPU Core Ultra
: 155H with the Xe 128 EU GPU. Other users have reported performance
: impact up to 30% on certain workloads. Please find more in the
: regressions reports:
: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14645
: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13845
:
: I believe the change should be backported to all active kernel branches
: after version 6.12.
To fix this issue, we can use the inode's size as a write size hint in
shmem_read_folio_gfp() to help allocate PMD-sized large folios.
Link: https://lkml.kernel.org/r/f7e64e99a3a87a8144cc6b2f1dddf7a89c12ce44.1753926601.git.baolin.wang@linux.alibaba.com Fixes: acd7ccb284b8 ("mm: shmem: add large folio support for tmpfs") Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com> Reported-by: Patryk Kowalczyk <patryk@kowalczyk.ws> Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Patryk Kowalczyk <patryk@kowalczyk.ws> Suggested-by: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "Some randome fixes and cleanups to swapfile".
Patch 0-3 are some random fixes. Patch 4 is a cleanup. More details can
be found in respective patches.
This patch (of 4):
When folio_alloc_swap() encounters a failure in either
mem_cgroup_try_charge_swap() or add_to_swap_cache(), nr_swap_pages counter
is not decremented for allocated entry. However, the following
put_swap_folio() will increase nr_swap_pages counter unpairly and lead to
an imbalance.
Move nr_swap_pages decrement from folio_alloc_swap() to swap_range_alloc()
to pair the nr_swap_pages counting.
In setup_swap_map(), we only ensure badpages are in range (0, last_page].
As maxpages might be < last_page, setup_clusters() will encounter a buffer
overflow when a badpage is >= maxpages.
Only call inc_cluster_info_page() for badpage which is < maxpages to fix
the issue.
Link: https://lkml.kernel.org/r/20250522122554.12209-4-shikemeng@huaweicloud.com Fixes: b843786b0bd0 ("mm: swapfile: fix SSD detection with swapfile on btrfs") Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kairui Song <kasong@tencent.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use maxpages from read_swap_header() to initialize swap_info_struct,
however the maxpages might be reduced in setup_swap_extents() and the
si->max is assigned with the reduced maxpages from the
setup_swap_extents().
Obviously, this could lead to memory waste as we allocated memory based on
larger maxpages, besides, this could lead to a potential deadloop as
following:
1) When calling setup_clusters() with larger maxpages, unavailable
pages within range [si->max, larger maxpages) are not accounted with
inc_cluster_info_page(). As a result, these pages are assumed
available but can not be allocated. The cluster contains these pages
can be moved to frag_clusters list after it's all available pages were
allocated.
2) When the cluster mentioned in 1) is the only cluster in
frag_clusters list, cluster_alloc_swap_entry() assume order 0
allocation will never failed and will enter a deadloop by keep trying
to allocate page from the only cluster in frag_clusters which contains
no actually available page.
Call setup_swap_extents() to get the final maxpages before
swap_info_struct initialization to fix the issue.
After this change, span will include badblocks and will become large
value which I think is correct value:
In summary, there are two kinds of swapfile_activate operations.
1. Filesystem style: Treat all blocks logical continuity and find
usable physical extents in logical range. In this way, si->pages will
be actual usable physical blocks and span will be "1 + highest_block -
lowest_block".
2. Block device style: Treat all blocks physically continue and only
one single extent is added. In this way, si->pages will be si->max and
span will be "si->pages - 1". Actually, si->pages and si->max is only
used in block device style and span value is set with si->pages. As a
result, span value in block device style will become a larger value as
you mentioned.
I think larger value is correct based on:
1. Span value in filesystem style is "1 + highest_block -
lowest_block" which is the range cover all possible phisical blocks
including the badblocks.
2. For block device style, si->pages is the actual usable block number
and is already in pr_info. The original span value before this patch
is also refer to usable block number which is redundant in pr_info.
Hardware or bootloader will initialize TLB entries to any value, which
may collide with kernel's UNIQUE_ENTRYHI value. On MIPS microAptiv/M5150
family of cores this will trigger machine check exception and cause boot
failure. On M5150 simulation this could happen 7 times out of 1000 boots.
Replace local_flush_tlb_all() with r4k_tlb_uniquify() which probes each
TLB ENTRIHI unique value for collisions before it's written, and in case
of collision try a different ASID.
Cc: stable@kernel.org Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8211dad627981 ("s390: add pte_free_defer() for pgtables sharing
page") added a warning to pte_free_defer(), on our request. It was meant
to warn if this would ever be reached for KVM guest mappings, because
the page table would be freed w/o a gmap_unlink(). THP mappings are not
allowed for KVM guests on s390, so this should never happen.
However, it is possible that the warning is triggered in a valid case as
false-positive.
s390_enable_sie() takes the mmap_lock, marks all VMAs as VM_NOHUGEPAGE and
splits possibly existing THP guest mappings. mm->context.has_pgste is set
to 1 before that, to prevent races with the mm_has_pgste() check in
MADV_HUGEPAGE.
khugepaged drops the mmap_lock for file mappings and might run in parallel,
before a vma is marked VM_NOHUGEPAGE, but after mm->context.has_pgste was
set to 1. If it finds file mappings to collapse, it will eventually call
pte_free_defer(). This will trigger the warning, but it is a valid case
because gmap is not yet set up, and the THP mappings will be split again.
When a zoned loop device, or zloop device, is removed, KASAN enabled
kernel reports "BUG KASAN use-after-free" in blk_mq_free_tag_set(). The
BUG happens because zloop_ctl_remove() calls put_disk(), which invokes
zloop_free_disk(). The zloop_free_disk() frees the memory allocated for
the zlo pointer. However, after the memory is freed, zloop_ctl_remove()
calls blk_mq_free_tag_set(&zlo->tag_set), which accesses the freed zlo.
Hence the KASAN use-after-free.
To avoid the BUG, move the call to blk_mq_free_tag_set(&zlo->tag_set)
from zloop_ctl_remove() into zloop_free_disk(). This ensures that
the tag_set is freed before the call to kvfree(zlo).
Most HCR_EL2 bits are not supposed to affect EL2 at all, but only
the guest. However, we gladly merge these bits with the host's
HCR_EL2 configuration, irrespective of entering L1 or L2.
This leads to some funky behaviour, such as L1 trying to inject
a virtual SError for L2, and getting a taste of its own medecine.
Not quite what the architecture anticipated.
In the end, the only bits that matter are those we have defined as
invariants, either because we've made them RESx (E2H, HCD...), or
that we actively refuse to merge because the mess with KVM's own
logic.
Use the sanitisation infrastructure to get the RES1 bits, and let
things rip in a safer way.
Fixes: 04ab519bb86df ("KVM: arm64: nv: Configure HCR_EL2 for FEAT_NV2") Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250721101955.535159-3-maz@kernel.org Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Brown reports that since we commit to making exceptions
visible without the vcpu being loaded, the external abort selftest
fails.
Upon investigation, it turns out that the code that makes registers
affected by an exception visible to the guest is completely broken
on VHE, as we don't check whether the system registers are loaded
on the CPU at this point. We managed to get away with this so far,
but that's obviously as bad as it gets,
Add the required checksm and document the absolute need to check
for the SYSREGS_ON_CPU flag before calling into any of the
__vcpu_write_sys_reg_to_cpu()__vcpu_read_sys_reg_from_cpu() helpers.
Let the guest set DEBUGCTL.RTM_DEBUG if RTM is supported according to the
guest CPUID model, as debug support is supposed to be available if RTM is
supported, and there are no known downsides to letting the guest debug RTM
aborts.
Note, there are no known bug reports related to RTM_DEBUG, the primary
motivation is to reduce the probability of breaking existing guests when a
future change adds a missing consistency check on vmcs12.GUEST_DEBUGCTL
(KVM currently lets L2 run with whatever hardware supports; whoops).
Note #2, KVM already emulates DR6.RTM, and doesn't restrict access to
DR7.RTM.
Fixes: 83c529151ab0 ("KVM: x86: expose Intel cpu new features (HLE, RTM) to guest") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250610232010.162191-5-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instruct vendor code to load the guest's DR6 into hardware via a new
KVM_RUN flag, and remove kvm_x86_ops.set_dr6(), whose sole purpose was to
load vcpu->arch.dr6 into hardware when DR6 can be read/written directly
by the guest.
Note, TDX already WARNs on any run_flag being set, i.e. will yell if KVM
thinks DR6 needs to be reloaded. TDX vCPUs force KVM_DEBUGREG_AUTO_SWITCH
and never clear the flag, i.e. should never observe KVM_RUN_LOAD_GUEST_DR6.
Convert kvm_x86_ops.vcpu_run()'s "force_immediate_exit" boolean parameter
into an a generic bitmap so that similar "take action" information can be
passed to vendor code without creating a pile of boolean parameters.
This will allow dropping kvm_x86_ops.set_dr6() in favor of a new flag, and
will also allow for adding similar functionality for re-loading debugctl
in the active VMCS.
Opportunistically massage the TDX WARN and comment to prepare for adding
more run_flags, all of which are expected to be mutually exclusive with
TDX, i.e. should be WARNed on.
Right now, if XRSTOR fails a console message like this is be printed:
Bad FPU state detected at restore_fpregs_from_fpstate+0x9a/0x170, reinitializing FPU registers.
However, the text location (...+0x9a in this case) is the instruction
*AFTER* the XRSTOR. The highlighted instruction in the "Code:" dump
also points one instruction late.
The reason is that the "fixup" moves RIP up to pass the bad XRSTOR and
keep on running after returning from the #GP handler. But it does this
fixup before warning.
The resulting warning output is nonsensical because it looks like the
non-FPU-related instruction is #GP'ing.
Do not fix up RIP until after printing the warning. Do this by using
the more generic and standard ex_handler_default().
Fixes: d5c8028b4788 ("x86/fpu: Reinitialize FPU registers if restoring FPU state fails") Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Chao Gao <chao.gao@intel.com> Acked-by: Alison Schofield <alison.schofield@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc:stable@vger.kernel.org Link: https://lore.kernel.org/all/20250624210148.97126F9E%40davehans-spike.ostc.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During communication with Focusrite Scarlett Gen 2/3/4 USB audio
interfaces, -EPROTO is sometimes returned from scarlett2_usb_tx(),
snd_usb_ctl_msg() which can cause initialisation and control
operations to fail intermittently.
This patch adds up to 5 retries in scarlett2_usb(), with a delay
starting at 5ms and doubling each time. This follows the same approach
as the fix for usb_set_interface() in endpoint.c (commit f406005e162b
("ALSA: usb-audio: Add retry on -EPROTO from usb_set_interface()")),
which resolved similar -EPROTO issues during device initialisation,
and is the same approach as in fcp.c:fcp_usb().
In __hdmi_lpe_audio_probe(), strscpy() is incorrectly called with the
length of the source string (excluding the NUL terminator) rather than
the size of the destination buffer. This results in one character less
being copied from 'card->shortname' to 'pcm->name'.
Use the destination buffer size instead to ensure the card name is
copied correctly.
Cc: stable@vger.kernel.org Fixes: 75b1a8f9d62e ("ALSA: Convert strlcpy to strscpy when return value is unused") Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev> Link: https://patch.msgid.link/20250805234156.60294-1-thorsten.blum@linux.dev Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An SNP cache coherency vulnerability requires a cache line eviction
mitigation when validating memory after a page state change to private.
The specific mitigation is to touch the first and last byte of each 4K
page that is being validated. There is no need to perform the mitigation
when performing a page state change to shared and rescinding validation.
CPUID bit Fn8000001F_EBX[31] defines the COHERENCY_SFW_NO CPUID bit that,
when set, indicates that the software mitigation for this vulnerability is
not needed.
Implement the mitigation and invoke it when validating memory (making it
private) and the COHERENCY_SFW_NO bit is not set, indicating the SNP guest
is vulnerable.
Co-developed-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit referenced in the Fixes tag causes usbnet to malfunction
(identified via git bisect). Post-commit, my external RJ45 LAN cable
fails to connect. Linus also reported the same issue after pulling that
commit.
The code has a logic error: netif_carrier_on() is only called when the
link is already on. Fix this by moving the netif_carrier_on() call
outside the if-statement entirely. This ensures it is always called
when EVENT_LINK_CARRIER_ON is set and properly clears it regardless
of the link state.
The Gemalto Cinterion PLS83-W modem (cdc_ether) is emitting confusing link
up and down events when the WWAN interface is activated on the modem-side.
Interrupt URBs will in consecutive polls grab:
* Link Connected
* Link Disconnected
* Link Connected
Where the last Connected is then a stable link state.
When the system is under load this may cause the unlink_urbs() work in
__handle_link_change() to not complete before the next usbnet_link_change()
call turns the carrier on again, allowing rx_submit() to queue new SKBs.
In that event the URB queue is filled faster than it can drain, ending up
in a RCU stall:
rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 0-.... } 33108 jiffies s: 201 root: 0x1/.
rcu: blocking rcu_node structures (internal RCU debug):
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
T99W709 is designed based on MTK T300(5G redcap) chip. There are
7 serial ports to be enumerated: AP_LOG, GNSS, AP_META, AT,
MD_META, NPT, DBG. RSVD(5) for ADB port.
In ksmbd_extract_shortname(), strscpy() is incorrectly called with the
length of the source string (excluding the NUL terminator) rather than
the size of the destination buffer. This results in "__" being copied
to 'extension' rather than "___" (two underscores instead of three).
Use the destination buffer size instead to ensure that the string "___"
(three underscores) is copied correctly.
Cc: stable@vger.kernel.org Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Repeated connections from clients with the same IP address may exhaust
the max connections and prevent other normal client connections.
This patch limit repeated connections from clients with the same IP.
Reported-by: tianshuo han <hantianshuo233@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 5c70eb5c593d ("net: better track kernel sockets lifetime"),
kernel sockets now use net_passive reference counting. However, commit 95d2b9f693ff ("Revert "smb: client: fix TCP timers deadlock after rmmod"")
restored the manual socket refcount manipulation without adapting to this
new mechanism, causing a memory leak.
The issue can be reproduced by[1]:
1. Creating a network namespace
2. Mounting and Unmounting CIFS within the namespace
3. Deleting the namespace
Some memory leaks may appear after a period of time following step 3.
Root cause:
When creating kernel sockets, sk_alloc() calls net_passive_inc() for
sockets with sk_net_refcnt=0. The CIFS code manually converts kernel
sockets to user sockets by setting sk_net_refcnt=1, but doesn't call
the corresponding net_passive_dec(). This creates an imbalance in the
net_passive counter, which prevents the network namespace from being
destroyed when its last user reference is dropped. As a result, the
entire namespace and all its associated resources remain allocated.
Timeline of patches leading to this issue:
- commit ef7134c7fc48 ("smb: client: Fix use-after-free of network
namespace.") in v6.12 fixed the original netns UAF by manually
managing socket refcounts
- commit e9f2517a3e18 ("smb: client: fix TCP timers deadlock after
rmmod") in v6.13 attempted to use kernel sockets but introduced
TCP timer issues
- commit 5c70eb5c593d ("net: better track kernel sockets lifetime")
in v6.14-rc5 introduced the net_passive mechanism with
sk_net_refcnt_upgrade() for proper socket conversion
- commit 95d2b9f693ff ("Revert "smb: client: fix TCP timers deadlock
after rmmod"") in v6.15-rc3 reverted to manual refcount management
without adapting to the new net_passive changes
Fix this by using sk_net_refcnt_upgrade() which properly handles the
net_passive counter when converting kernel sockets to user sockets.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220343 Fixes: 95d2b9f693ff ("Revert "smb: client: fix TCP timers deadlock after rmmod"") Cc: stable@vger.kernel.org Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com> Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de> Signed-off-by: Wang Zhaolong <wangzhaolong@huaweicloud.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If client send multiple session setup requests to ksmbd,
Preauh_HashValue race condition could happen.
There is no need to free sess->Preauh_HashValue at session setup phase.
It can be freed together with session at connection termination phase.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-27661 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If client send two session setups with krb5 authenticate to ksmbd,
null pointer dereference error in generate_encryptionkey could happen.
sess->Preauth_HashValue is set to NULL if session is valid.
So this patch skip generate encryption key if session is valid.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-27654 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for a vsock to autobind to VMADDR_PORT_ANY. This can
cause a use-after-free when a connection is made to the bound socket.
The socket returned by accept() also has port VMADDR_PORT_ANY but is not
on the list of unbound sockets. Binding it will result in an extra
refcount decrement similar to the one fixed in fcdd2242c023 (vsock: Keep
the binding until socket destruction).
Modify the check in __vsock_bind_connectible() to also prevent binding
to VMADDR_PORT_ANY.
When packet_set_ring() releases po->bind_lock, another thread can
run packet_notifier() and process an NETDEV_UP event.
This race and the fix are both similar to that of commit 15fe076edea7
("net/packet: fix a race in packet_bind() and packet_notifier()").
There too the packet_notifier NETDEV_UP event managed to run while a
po->bind_lock critical section had to be temporarily released. And
the fix was similarly to temporarily set po->num to zero to keep
the socket unhooked until the lock is retaken.
The po->bind_lock in packet_set_ring and packet_notifier precede the
introduction of git history.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Signed-off-by: Quang Le <quanglex97@gmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20250801175423.2970334-1-willemdebruijn.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exercise various mmap(), munmap() and mremap() invocations, which might
cause a perf buffer mapping to be split or truncated.
To avoid hard coding the perf event and having dependencies on
architectures and configuration options, scan through event types in sysfs
and try to open them. On success, try to mmap() and if that succeeds try to
mmap() the AUX buffer.
In case that no AUX buffer supporting event is found, only test the base
buffer mapping. If no mappable event is found or permissions are not
sufficient, skip the tests.
Reserve a PROT_NONE region for both rb and aux tests to allow testing the
case where mremap unmaps beyond the end of a mapped VMA to prevent it from
unmapping unrelated mappings.
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Co-developed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The perf mmap code is careful about mmap()'ing the user page with the
ringbuffer and additionally the auxiliary buffer, when the event supports
it. Once the first mapping is established, subsequent mapping have to use
the same offset and the same size in both cases. The reference counting for
the ringbuffer and the auxiliary buffer depends on this being correct.
Though perf does not prevent that a related mapping is split via mmap(2),
munmap(2) or mremap(2). A split of a VMA results in perf_mmap_open() calls,
which take reference counts, but then the subsequent perf_mmap_close()
calls are not longer fulfilling the offset and size checks. This leads to
reference count leaks.
As perf already has the requirement for subsequent mappings to match the
initial mapping, the obvious consequence is that VMA splits, caused by
resizing of a mapping or partial unmapping, have to be prevented.
Implement the vm_operations_struct::may_split() callback and return
unconditionally -EINVAL.
That ensures that the mapping offsets and sizes cannot be changed after the
fact. Remapping to a different fixed address with the same size is still
possible as it takes the references for the new mapping and drops those of
the old mapping.
Fixes: 45bfb2e50471 ("perf/core: Add AUX area to ring buffer for raw data streams") Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-27504 Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After successful allocation of a buffer or a successful attachment to an
existing buffer perf_mmap() tries to map the buffer read only into the page
table. If that fails, the already set up page table entries are zapped, but
the other perf specific side effects of that failure are not handled. The
calling code just cleans up the VMA and does not invoke perf_mmap_close().
This leaks reference counts, corrupts user->vm accounting and also results
in an unbalanced invocation of event::event_mapped().
Cure this by moving the event::event_mapped() invocation before the
map_range() call so that on map_range() failure perf_mmap_close() can be
invoked without causing an unbalanced event::event_unmapped() call.
perf_mmap_close() undoes the reference counts and eventually frees buffers.
Fixes: b709eb872e19 ("perf/core: map pages in advance") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When perf_mmap() fails to allocate a buffer, it still invokes the
event_mapped() callback of the related event. On X86 this might increase
the perf_rdpmc_allowed reference counter. But nothing undoes this as
perf_mmap_close() is never called in this case, which causes another
reference count leak.
Return early on failure to prevent that.
Fixes: 1e0fb9ec679c ("perf/core: Add pmu callbacks to track event mapping and unmapping") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failure of the AUX buffer allocation leaks the reference count.
Set the reference count to 1 only when the allocation succeeds.
Fixes: 45bfb2e50471 ("perf/core: Add AUX area to ring buffer for raw data streams") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent overhaul sets the return value to 0 unconditionally after the
allocations, which causes reference count leaks and corrupts the user->vm
accounting.
Preserve the AUX buffer allocation failure return value, so that the
subsequent code works correctly.
Fixes: 0983593f32c4 ("perf/core: Lift event->mmap_mutex in perf_mmap()") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scott Mayhew discovered a security exploit in NFS over TLS in
tls_alert_recv() due to its assumption it can read data from
the msg iterator's kvec..
kTLS implementation splits TLS non-data record payload between
the control message buffer (which includes the type such as TLS
aler or TLS cipher change) and the rest of the payload (say TLS
alert's level/description) which goes into the msg payload buffer.
This patch proposes to rework how control messages are setup and
used by sock_recvmsg().
If no control message structure is setup, kTLS layer will read and
process TLS data record types. As soon as it encounters a TLS control
message, it would return an error. At that point, NFS can setup a
kvec backed msg buffer and read in the control message such as a
TLS alert. Msg iterator can advance the kvec pointer as a part of
the copy process thus we need to revert the iterator before calling
into the tls_alert_recv.
Reported-by: Scott Mayhew <smayhew@redhat.com> Fixes: 5e052dda121e ("SUNRPC: Recognize control messages in server-side TCP socket code") Suggested-by: Trond Myklebust <trondmy@hammerspace.com> Cc: stable@vger.kernel.org Signed-off-by: Olga Kornievskaia <okorniev@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If two calls to nfsd_open_local_fh() race and both successfully call
nfsd_file_acquire_local(), they will both get an extra reference to the
net to accompany the file reference stored in *pnf.
One of them will fail to store (using xchg()) the file reference in
*pnf and will drop that reference but WON'T drop the accompanying
reference to the net. This leak means that when the nfs server is shut
down it will hang in nfsd_shutdown_net() waiting for
&nn->nfsd_net_free_done.
This patch adds the missing nfsd_net_put().
Reported-by: Mike Snitzer <snitzer@kernel.org> Fixes: e6f7e1487ab5 ("nfs_localio: simplify interface to nfsd for getting nfsd_file") Cc: stable@vger.kernel.org Signed-off-by: NeilBrown <neil@brown.name> Tested-by: Mike Snitzer <snitzer@kernel.org> Reviewed-by: Mike Snitzer <snitzer@kernel.org> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clients will typically precede a DELEGRETURN for a delegation with
delegated timestamp with a SETATTR to set the timestamps on the server
to match what the client has.
knfsd implements this by using the nfsd_setattr() infrastructure, which
will set ATTR_CTIME on any update that goes to notify_change(). This is
problematic as it means that the client will get a spurious ctime
update when updating the atime.
POSIX unfortunately doesn't phrase it succinctly, but updating the atime
due to reads should not update the ctime. In this case, the client is
sending a SETATTR to update the atime on the server to match its latest
value. The ctime should not be advanced in this case as that would
incorrectly indicate a change to the inode.
Fix this by not implicitly setting ATTR_CTIME when ATTR_DELEG is set in
__nfsd_setattr(). The decoder for FATTR4_WORD2_TIME_DELEG_MODIFY already
sets ATTR_CTIME, so this is sufficient to make it skip setting the ctime
on atime-only updates.
Fixes: 7e13f4f8d27d ("nfsd: handle delegated timestamps in SETATTR") Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Together with the RAPL MSRs, there are more MSRs gone on DMR, including
PLR (Perf Limit Reasons), and IRTL (Package cstate Interrupt Response
Time Limit) MSRs. The configurable TDP info should also be retrieved
from TPMI based Intel Speed Select Technology feature.
Remove the access of these MSRs for DMR. Improve the DMR platform
feature table to make it more readable at the same time.
Fixes: 83075bd59de2 ("tools/power turbostat: Add initial support for DMR") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: f198186aa9bb ("CIFS: SMBD: Establish SMB Direct connection") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 528589947c180 ("nvmet: initialize discovery subsys after debugfs
is initialized") changed nvmet_init() to initialize nvme discovery after
"nvmet" debugfs directory is initialized. The change broke nvmet_exit()
because discovery subsystem now depends on debugfs. Debugfs should be
destroyed after discovery subsystem. Fix nvmet_exit() to do that.
Reported-by: Yi Zhang <yi.zhang@redhat.com> Closes: https://lore.kernel.org/all/CAHj4cs96AfFQpyDKF_MdfJsnOEo=2V7dQgqjFv+k3t7H-=yGhA@mail.gmail.com/ Fixes: 528589947c180 ("nvmet: initialize discovery subsys after debugfs is initialized") Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Daniel Wagner <dwagner@suse.de> Link: https://lore.kernel.org/r/20250807053507.2794335-1-mkhalfella@purestorage.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling enqueue_reassembly() and wake_up_interruptible(&info->wait_reassembly_queue)
or put_receive_buffer() means the response/data_transfer pointer might
get re-used by another thread, which means these should be
the last operations before calling return.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: f198186aa9bb ("CIFS: SMBD: Establish SMB Direct connection") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should call put_receive_buffer() before waking up the callers.
For the internal error case of response->type being unexpected,
we now also call smbd_disconnect_rdma_connection() instead
of not waking up the callers at all.
Note that the SMBD_TRANSFER_DATA case still has problems,
which will be addressed in the next commit in order to make
it easier to review this one.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: f198186aa9bb ("CIFS: SMBD: Establish SMB Direct connection") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of failures either ib_dma_map_single() might not be called yet
or ib_dma_unmap_single() was already called.
We should make sure put_receive_buffer() only calls
ib_dma_unmap_single() if needed.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: f198186aa9bb ("CIFS: SMBD: Establish SMB Direct connection") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's no need to maintain two lists, we can just
have a single list of receive buffers, which are free to use.
It just added unneeded complexity and resulted in
ib_dma_unmap_single() not being called from recv_done()
for empty keepalive packets.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: Long Li <longli@microsoft.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: f198186aa9bb ("CIFS: SMBD: Establish SMB Direct connection") Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling enqueue_reassembly() and wake_up_interruptible(&t->wait_reassembly_queue)
or put_receive_buffer() means the recvmsg/data_transfer pointer might
get re-used by another thread, which means these should be
the last operations before calling return.
Cc: Namjae Jeon <linkinjeon@kernel.org> Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Stefan Metzmacher <metze@samba.org> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should call put_recvmsg() before smb_direct_disconnect_rdma_connection()
in order to call it before waking up the callers.
In all error cases we should call smb_direct_disconnect_rdma_connection()
in order to avoid stale connections.
Cc: Namjae Jeon <linkinjeon@kernel.org> Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Stefan Metzmacher <metze@samba.org> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of failures either ib_dma_map_single() might not be called yet
or ib_dma_unmap_single() was already called.
We should make sure put_recvmsg() only calls ib_dma_unmap_single() if needed.
Cc: Namjae Jeon <linkinjeon@kernel.org> Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Stefan Metzmacher <metze@samba.org> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's no need to maintain two lists, we can just
have a single list of receive buffers, which are free to use.
Cc: Steve French <smfrench@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Stefan Metzmacher <metze@samba.org> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hda-sdw-bpt code links against the soundwire driver, but that fails when
trying to link from built-in code into loadable module:
x86_64-linux-ld: vmlinux.o: in function `intel_ace2x_bpt_close_stream.isra.0':
intel_ace2x.c:(.text+0x137a531): undefined reference to `hda_sdw_bpt_close'
x86_64-linux-ld: vmlinux.o: in function `intel_ace2x_bpt_send_async':
intel_ace2x.c:(.text+0x137aa45): undefined reference to `hda_sdw_bpt_open'
x86_64-linux-ld: intel_ace2x.c:(.text+0x137ab67): undefined reference to `hda_sdw_bpt_close'
x86_64-linux-ld: intel_ace2x.c:(.text+0x137ac30): undefined reference to `hda_sdw_bpt_send_async'
x86_64-linux-ld: vmlinux.o: in function `intel_ace2x_bpt_wait':
intel_ace2x.c:(.text+0x137aced): undefined reference to `hda_sdw_bpt_wait'
Ensure that both SOUNDWIRE_INTEL and SND_SOF_SOF_HDA_SDW_BPT are selected
at the same time by SND_SOC_SOF_INTEL_LNL, and that this happens even if
SND_SOC_SOF_INTEL_SOUNDWIRE is a loadable module but SND_SOC_SOF_INTEL_LNL
is built-in.
This follows the same logic as commit c5a61db9bf89 ("ASoC: SOF: fix
intel-soundwire link failure").
Fixes: 5d5cb86fb46e ("ASoC: SOF: Intel: hda-sdw-bpt: add helpers for SoundWire BPT DMA") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://patch.msgid.link/20250805160451.4004602-1-arnd@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compile-testing IMX_MU_MSI on x86 without PCI_MSI support results in a
build failure:
drivers/gpio/gpio-sprd.c:8:
include/linux/gpio/driver.h:41:33: error: field 'msiinfo' has incomplete type
drivers/iommu/iommufd/viommu.c:4:
include/linux/msi.h:528:33: error: field 'alloc_info' has incomplete type
Tighten the dependency further to only allow compile testing on Arm.
This could be refined further to allow certain x86 configs.
This was submitted before to address a different build failure, which was
fixed differently, but the problem has now returned in a different form.
emac_rx_packet() is a common function for handling traffic
for both xdp and non-xdp use cases. Use common logic for
handling skb with or without xdp to prevent any incorrect
packet processing. This patch fixes ping working with
XDP_PASS for icssg driver.
In order for the wait in nfs_uuid_put() to be safe, it is necessary to
ensure that nfs_uuid_add_file() doesn't add a new entry once the
nfs_uuid->net has been NULLed out.
Also fix up the wake_up_var_locked() / wait_var_event_spinlock() to both
use the nfs_uuid address, since nfl, and &nfl->uuid could be used elsewhere.
Acked-by: Mike Snitzer <snitzer@kernel.org> Tested-by: Mike Snitzer <snitzer@kernel.org> Link: https://lore.kernel.org/all/175262893035.2234665.1735173020338594784@noble.neil.brown.name/ Fixes: 21fb44034695 ("nfs_localio: protect race between nfs_uuid_put() and nfs_close_local_fh()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Wrap copying of drop stats on TX path from fbd->hw_stats by the
hw_stats_lock. Currently, it is being performed outside the lock and
another thread accessing fbd->hw_stats can lead to inconsistencies.
Fixes: 5f8bd2ce8269 ("eth: fbnic: add support for TMI stats") Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250802024636.679317-3-mohsin.bashr@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Alex added page bias of LONG_MAX, which is admittedly quite
a clever way of catching overflows of the pp ref count.
The page pool code was "optimized" to leave the ref at 1
for freed pages so it can't catch basic bugs by itself any more.
(Something we should probably address under DEBUG_NET...)
Unfortunately for fbnic since commit f7dc3248dcfb ("skbuff: Optimization
of SKB coalescing for page pool") core _may_ actually take two extra
pp refcounts, if one of them is returned before driver gives up the bias
the ret < 0 check in page_pool_unref_netmem() will trigger.
While at it add a FBNIC_ to the name of the driver constant.
Make vmem_pte_alloc() consistent by always allocating page table of
PAGE_SIZE granularity, regardless of whether page_table_alloc() (with
slab) or memblock_alloc() is used. This ensures page table can be fully
freed when the corresponding page table entries are removed.
Fixes: d08d4e7cd6bf ("s390/mm: use full 4KB page for 2KB PTE") Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
TCA_MQPRIO_TC_ENTRY_INDEX is validated using
NLA_POLICY_MAX(NLA_U32, TC_QOPT_MAX_QUEUE), which allows the value
TC_QOPT_MAX_QUEUE (16). This leads to a 4-byte out-of-bounds stack
write in the fp[] array, which only has room for 16 elements (0–15).
Fix this by changing the policy to allow only up to TC_QOPT_MAX_QUEUE - 1.
Fixes: f62af20bed2d ("net/sched: mqprio: allow per-TC user input of FP adminStatus") Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Maher Azzouzi <maherazz04@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250802001857.2702497-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using devm_*() [here] is completely wrong, because this is called
from mdiobus_register_device(). This is not the probe function
for the device, and thus there is no code to trigger the release of
the resource on unregistration.
Moreover, when the mdiodev is eventually probed, if the driver fails
or the driver is unbound, the GPIO will be released, but a reference
will be left behind.
Using devm* with a struct device that is *not* currently being probed
is fundamentally wrong - an abuse of devm.
projects / thirdparty / kernel / stable.git / log
