High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Peter Chen <Peter.Chen@freescale.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 3dc6475 ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:
CC drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function
Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.
Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com> Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
acpi_processor_set_throttling() uses set_cpus_allowed_ptr() to make
sure that the (struct acpi_processor)->acpi_processor_set_throttling()
callback will run on the right CPU. However, the function may be
called from a worker thread already bound to a different CPU in which
case that won't work.
Make acpi_processor_set_throttling() use work_on_cpu() as appropriate
instead of abusing set_cpus_allowed_ptr().
Reported-and-tested-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
[rjw: Changelog] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Some devices have duplicate entries in there brightness levels table, ie
on my Dell Latitude E6430 the table looks like this:
[ 3.686060] acpi backlight index 0, val 80
[ 3.686095] acpi backlight index 1, val 50
[ 3.686122] acpi backlight index 2, val 5
[ 3.686147] acpi backlight index 3, val 5
[ 3.686172] acpi backlight index 4, val 5
[ 3.686197] acpi backlight index 5, val 5
[ 3.686223] acpi backlight index 6, val 5
[ 3.686248] acpi backlight index 7, val 5
[ 3.686273] acpi backlight index 8, val 6
[ 3.686332] acpi backlight index 9, val 7
[ 3.686356] acpi backlight index 10, val 8
[ 3.686380] acpi backlight index 11, val 9
etc.
Notice that brightness values 0-5 are all mapped to 5. This means that
if userspace writes any value between 0 and 5 to the brightness sysfs attribute
and then reads it, it will always return 0, which is somewhat unexpected.
This is a problem for ie gnome-settings-daemon, which uses read-modify-write
logic when the users presses the brightness up or down keys. This is done
this way to take brightness changes from other sources into account.
On this specific laptop what happens once the brightness has been set to 0,
is that gsd reads 0, adds 5, writes 5, and on the next brightness up key press
again reads 0, so things get stuck at the lowest brightness setting.
Filtering out the duplicate table entries, makes any write to brightness
read back as the written value as one would expect, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The reference count changes done by pci_get_device can be a little
misleading when the usage diverges from the most common scheme. The
reference count of the device passed as the last parameter is always
decreased, even if the function returns no new device. So if we are
going to try alternative device IDs, we must manually increment the
device reference count before each retry. If we don't, we end up
decreasing the reference count, and after a few modprobe/rmmod cycles
the PCI devices will vanish.
In other words and as Alan put it: without this fix the EDAC code
corrupts the PCI device list.
This fixes kernel bug #50491:
https://bugzilla.kernel.org/show_bug.cgi?id=50491
acpi_pci_link_allocate_irq() can return negative gsi even if
entry != NULL. For that case we have a memory leak, so free
entry before returning from acpi_pci_irq_enable() for gsi < 0.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
[rjw: Subject and changelog] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts. Clear Interrupt Disable so we get those interrupts.
Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.
Marvell SoCs place the SoC number into the PCIe endpoint device ID. The
SoC stepping is placed into the PCIe revision. The old plat-orion PCIe
driver allowed this information to be seen in user space with a simple
lspci command.
The new driver places a virtual PCI-PCI bridge on top of these endpoints.
It has its own hard coded PCI device ID. Thus it is no longer possible to
see what the SoC is using lspci.
When initializing the PCI-PCI bridge, set its device ID and revision from
the underlying endpoint, thus restoring this functionality. Debian would
like to use this in order to aid installing the correct DTB file.
Fixes: 45361a4fe4464 ("pci: PCIe driver for Marvell Armada 370/XP systems") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The powernow-k8 driver maintains a per-cpu data-structure called
powernow_data that is used to perform the frequency transitions.
It initializes this data structure only for the policy->cpu. So,
accesses to this data structure by other CPUs results in various
problems because they would have been uninitialized.
Specifically, if a cpu (!= policy->cpu) invokes the drivers' ->get()
function, it returns 0 as the KHz value, since its per-cpu memory
doesn't point to anything valid. This causes problems during
suspend/resume since cpufreq_update_policy() tries to enforce this
(0 KHz) as the current frequency of the CPU, and this madness gets
propagated to adjust_jiffies() as well. Eventually, lots of things
start breaking down, including the r8169 ethernet card, in one
particularly interesting case reported by Pierre Ossman.
Fix this by initializing the per-cpu data-structures of all the CPUs
in the policy appropriately.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70311 Reported-by: Pierre Ossman <pierre@ossman.eu> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It's a bit odd to see a newer device showing mod15write; however, the
reported behavior is highly consistent and other factors which could
contribute seem to have been verified well enough. Also, both
sata_sil itself and the drive are fairly outdated at this point making
the risk of this change fairly low. It is possible, probably likely,
that other drive models in the same family have the same problem;
however, for now, let's just add the specific model which was tested.
Without the patch the kernel generates the following error.
ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123'
ata11.15: PMP revalidation failed (errno=-19)
ata11.15: failed to recover PMP after 5 tries, giving up
This patch helps to bypass this error and the device becomes
functional.
Vince "Super Tester" Weaver reported a new round of syscall fuzzing (Trinity) failures,
with perf WARN_ON()s triggering. He also provided traces of the failures.
We try and add the {BP,cycles,br_insn} group (fd[3], fd[4], fd[15]).
These events are 0:cycles and 4:br_insn, the BP event isn't x86_pmu so
that's not visible.
group_sched_in()
pmu->start_txn() /* nop - BP pmu */
event_sched_in()
event->pmu->add()
But seeing the below state on x86_pmu_enable(), the must have failed,
because the 0 and 4 events aren't there anymore.
Looking at group_sched_in(), since the BP is the leader, its
event_sched_in() must have succeeded, for otherwise we would not have
seen the sibling adds.
But since neither 0 or 4 are in the below state; their event_sched_in()
must have failed; but I don't see why, the complete state: 0,0,1:p,4
fits perfectly fine on a core2.
However, since we try and schedule 4 it means the 0 event must have
succeeded! Therefore the 4 event must have failed, its failure will
have put group_sched_in() into the fail path, which will call:
event_sched_out()
event->pmu->del()
on 0 and the BP event.
Now x86_pmu_del() will reduce n_events; but it will not reduce n_added;
giving what we see below:
So the problem is that x86_pmu_del(), when called from a
group_sched_in() that fails (for whatever reason), and without x86_pmu
TXN support (because the leader is !x86_pmu), will corrupt the n_added
state.
Reported-and-Tested-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Stephane Eranian <eranian@google.com> Cc: Dave Jones <davej@redhat.com> Link: http://lkml.kernel.org/r/20140221150312.GF3104@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
GFP_ATOMIC is not a single gfp flag, but a macro which expands to the other
flags, where meaningful is the LACK of __GFP_WAIT flag. To check if caller
wants to perform an atomic allocation, the code must test for a lack of the
__GFP_WAIT flag. This patch fixes the issue introduced in v3.5-rc1.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
In copy_oldmem_page, the current check using max_pfn and min_low_pfn to
decide if the page is backed or not, is not valid when the memory layout is
not continuous.
This happens when running as a QEMU/KVM guest, where RTAS is mapped higher
in the memory. In that case max_pfn points to the end of RTAS, and a hole
between the end of the kdump kernel and RTAS is not backed by PTEs. As a
consequence, the kdump kernel is crashing in copy_oldmem_page when accessing
in a direct way the pages in that hole.
This fix relies on the memblock's service memblock_is_region_memory to
check if the read page is part or not of the directly accessible memory.
Currently we're storing a host endian RTAS token in
rtas_stop_self_args.token. We then pass that directly to rtas. This is
fine on big endian however on little endian the token is not what we
expect.
This will typically result in hitting:
panic("Alas, I survived.\n");
To fix this we always use the stop-self token in host order and always
convert it to be32 before passing this to rtas.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The new ELFv2 little-endian ABI increases the stack redzone -- the
area below the stack pointer that can be used for storing data --
from 288 bytes to 512 bytes. This means that we need to allow more
space on the user stack when delivering a signal to a 64-bit process.
To make the code a bit clearer, we define new USER_REDZONE_SIZE and
KERNEL_REDZONE_SIZE symbols in ptrace.h. For now, we leave the
kernel redzone size at 288 bytes, since increasing it to 512 bytes
would increase the size of interrupt stack frames correspondingly.
Gcc currently only makes use of 288 bytes of redzone even when
compiling for the new little-endian ABI, and the kernel cannot
currently be compiled with the new ABI anyway.
In the future, hopefully gcc will provide an option to control the
amount of redzone used, and then we could reduce it even more.
This also changes the code in arch_compat_alloc_user_space() to
preserve the expanded redzone. It is not clear why this function would
ever be used on a 64-bit process, though.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix a race in which the RPC client is shutting down while the
gss daemon is processing a downcall. If the RPC client manages to
shut down before the gss daemon is done, then the struct gss_auth
used in gss_release_msg() may have already been freed.
When a send failure occurs due to the socket being out of buffer space,
we call xs_nospace() in order to have the RPC task wait until the
socket has drained enough to make it worth while trying again.
The current patch fixes a race in which the socket is drained before
we get round to setting up the machinery in xs_nospace(), and which
is reported to cause hangs.
Link: http://lkml.kernel.org/r/20140210170315.33dfc621@notabene.brown Fixes: a9a6b52ee1ba (SUNRPC: Don't start the retransmission timer...) Reported-by: Neil Brown <neilb@suse.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There is a typo in the Limiter2 Release Rate control, a wrong enum for
Limiter1 is assigned. It must point to Limiter2.
Spotted by a compile warning:
In file included from sound/soc/codecs/sta32x.c:34:0:
sound/soc/codecs/sta32x.c:223:29: warning: ‘sta32x_limiter2_release_rate_enum’ defined but not used [-Wunused-variable]
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
include/sound/soc.h:275:18: note: in definition of macro ‘SOC_ENUM_DOUBLE_DECL’
struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/codecs/sta32x.c:223:8: note: in expansion of macro ‘SOC_ENUM_SINGLE_DECL’
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The driver reads from the DC offset control registers during callibration
but since the registers are marked as volatile and there is a register
cache the values will not be read from the hardware after the first reading
rendering the callibration ineffective.
It appears that the driver was originally written for the ASoC level
register I/O code but converted to regmap prior to merge and this issue
was missed during the conversion as the framework level volatile register
functionality was not being used.
Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Sync regcache when entering STANDBY from OFF. ON isn't entered with
OFF as the current state, so the registers were not being re-synced
after suspend/resume.
The 98088 and 98095 already call regcache_sync from STANDBY.
Signed-off-by: Dylan Reid <dgreid@chromium.org> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch fixes a crash caused by commit 3bed3344c826
(ASoC: txx9aclc_ac97: Convert to devm_ioremap_resource()).
This is an attempt to assign "drvdata->base" while memory
for "drvdata" is not already allocated.
Fixes: 3bed3344c826 (ASoC: txx9aclc_ac97: Convert to devm_ioremap_resource()) Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently the I2C device Ids conflict for the MFD and CODEC so
cannot be both instantiated on one platform. This patch updates
the Ids and names to make them unique from each other.
It should be noted that the I2C addresses for both PMIC and CODEC
are modifiable so instantiation of the two are kept as separate
devices, rather than instantiating the CODEC from the MFD code.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Acked-by: Mark Brown <broonie@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The problem occurs when the guest performs a pusha with the stack
address pointing to an mmio address (or an invalid guest physical
address) to start with, but then extending into an ordinary guest
physical address. When doing repeated emulated pushes
emulator_read_write sets mmio_needed to 1 on the first one. On a
later push when the stack points to regular memory,
mmio_nr_fragments is set to 0, but mmio_is_needed is not set to 0.
As a result, KVM exits to userspace, and then returns to
complete_emulated_mmio. In complete_emulated_mmio
vcpu->mmio_cur_fragment is incremented. The termination condition of
vcpu->mmio_cur_fragment == vcpu->mmio_nr_fragments is never achieved.
The code bounces back and fourth to userspace incrementing
mmio_cur_fragment past it's buffer. If the guest does nothing else it
eventually leads to a a crash on a memcpy from invalid memory address.
However if a guest code can cause the vm to be destroyed in another
vcpu with excellent timing, then kvm_clear_async_pf_completion_queue
can be used by the guest to control the data that's pointed to by the
call to cancel_work_item, which can be used to gain execution.
Fixes: f78146b0f9230765c6315b2e14f56112513389ad Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently notify_change directly updates i_version for size updates,
which not only is counter to how all other fields are updated through
struct iattr, but also breaks XFS, which need inode updates to happen
under its own lock, and synchronized to the structure that gets written
to the log.
Remove the update in the common code, and it to btrfs and ext4,
XFS already does a proper updaste internally and currently gets a
double update with the existing code.
IMHO this is 3.13 and -stable material and should go in through the XFS
tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Acked-by: Jan Kara <jack@suse.cz> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Ben Myers <bpm@sgi.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently, there's nothing preventing cgroup_enable_task_cg_lists()
from missing set PF_EXITING and race against cgroup_exit(). Depending
on the timing, cgroup_exit() may finish with the task still linked on
css_set leading to list corruption. Fix it by grabbing siglock in
cgroup_enable_task_cg_lists() so that PF_EXITING is guaranteed to be
visible.
This whole on-demand cg_list optimization is extremely fragile and has
ample possibility to lead to bugs which can cause things like
once-a-year oops during boot. I'm wondering whether the better
approach would be just adding "cgroup_disable=all" handling which
disables the whole cgroup rather than tempting fate with this
on-demand craziness.
cgroup_cfts_commit() walks the cgroup hierarchy that the target
subsystem is attached to and tries to apply the file changes. Due to
the convolution with inode locking, it can't keep cgroup_mutex locked
while iterating. It currently holds only RCU read lock around the
actual iteration and then pins the found cgroup using dget().
Unfortunately, this is incorrect. Although the iteration does check
cgroup_is_dead() before invoking dget(), there's nothing which
prevents the dentry from going away inbetween. Note that this is
different from the usual css iterations where css_tryget() is used to
pin the css - css_tryget() tests whether the css can be pinned and
fails if not.
The problem can be solved by simply holding cgroup_mutex instead of
RCU read lock around the iteration, which actually reduces LOC.
When cgroup_mount() fails to allocate an id for the root, it didn't
set ret before jumping to unlock_drop ending up returning 0 after a
failure. Fix it.
The front headphone and mic jackes on a HP desktop model (Vendor Id:
0x111d76c7 Subsystem Id: 0x103c2b17) can not work, the codec on this
machine has 8 physical ports, 6 of them are routed to rear jackes
and all of them work very well, while the remaining 2 ports are
routed to front headphone and mic jackes, but the corresponding
pin complex node are not defined correctly.
After apply this fix, the front audio jackes can work very well.
[trivial fix of enum definition by tiwai]
BugLink: https://bugs.launchpad.net/bugs/1282369 Cc: David Henningsson <david.henningsson@canonical.com> Tested-by: Gerald Yang <gerald.yang@canonical.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Incorrect ADC is picked in ca0132_capture_pcm_prepare(),
where it assumes multiple streams while there is one stream
per ADC. Note that ca0132_capture_pcm_cleanup() already does
the right thing.
The Chromebook Pixel has a microphone under the keyboard that
is attached to node id 0x8. Before this fix, recording would
always go to the main internal mic (node id 0x7).
When a HDMI stream is opened with the same stream tag
as a following opened stream to ca0132, audio will be
heard from two ports simultaneously.
Fix this issue by change to use snd_hda_codec_setup_stream
and snd_hda_codec_cleanup_stream instead, so that an
inactive stream can be marked as 'dirty' when found
with a conflict stream tag, and then get purified.
When the driver tries to access Function Unit 10, the KEF X300A
speakers' firmware apparently locks up, making even PCM streaming
impossible. Work around this by ignoring this FU.
1. wpa_supplicant send a start_scan request to the nl80211 driver
2. mac80211 module call rtl_op_config with IEEE80211_CONF_CHANGE_IDLE
3. rtl_ips_nic_on is called which disable local irqs
4. rtl92c_phy_set_rf_power_state() is called
5. rtl_ps_enable_nic() is called and hw_init()is executed and then the interrupts on the device are enabled
A good solution could be to refactor the code to avoid calling rtl92ce_hw_init() with the irqs disabled
but a quick and dirty solution that has proven to work is
to reenable the irqs during the function rtl92ce_hw_init().
I think that it is safe doing so since the device interrupt will only be enabled after the init function succeed.
Signed-off-by: Olivier Langlois <olivier@trillion01.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch fixes regression caused by commit a16dad77634 "MIPS: Fix
potencial corruption". That commit fixes one corruption scenario in
cost of adding another one, which actually start to cause crashes
on Yeeloong laptop when rtl8187 driver is used.
For correct DMA read operation on machines without DMA coherence, kernel
have to invalidate cache, such it will refill later with new data that
device wrote to memory, when that data is needed to process. We can only
invalidate full cache line. Hence when cache line includes both dma
buffer and some other data (written in cache, but not yet in main
memory), the other data can not hit memory due to invalidation. That
happen on rtl8187 where struct rtl8187_priv fields are located just
before and after small buffers that are passed to USB layer and DMA
is performed on them.
To fix the problem we align buffers and reserve space after them to make
them match cache line.
This patch does not resolve all possible MIPS problems entirely, for
that we have to assure that we always map cache aligned buffers for DMA,
what can be complex or even not possible. But patch fixes visible and
reproducible regression and seems other possible corruptions do not
happen in practice, since Yeeloong laptop works stable without rtl8187
driver.
Reported-by: Petr Pisar <petr.pisar@atlas.cz> Bisected-by: Tom Li <biergaizi2009@gmail.com> Reported-and-tested-by: Tom Li <biergaizi2009@gmail.com> Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Acked-by: Larry Finger <Larry.Finger@lwfinger.next> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
SMB3 servers can respond with MaxTransactSize of more than 4M
that can cause a memory allocation error returned from kmalloc
in a lock codepath. Also the client doesn't support multicredit
requests now and allows buffer sizes of 65536 bytes only. Set
MaxTransactSize to this maximum supported value.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It's possible for userland to pass down an iovec via writev() that has a
bogus user pointer in it. If that happens and we're doing an uncached
write, then we can end up getting less bytes than we expect from the
call to iov_iter_copy_from_user. This is CVE-2014-0069
cifs_iovec_write isn't set up to handle that situation however. It'll
blindly keep chugging through the page array and not filling those pages
with anything useful. Worse yet, we'll later end up with a negative
number in wdata->tailsz, which will confuse the sending routines and
cause an oops at the very least.
Fix this by having the copy phase of cifs_iovec_write stop copying data
in this situation and send the last write as a short one. At the same
time, we want to avoid sending a zero-length write to the server, so
break out of the loop and set rc to -EFAULT if that happens. This also
allows us to handle the case where no address in the iovec is valid.
[Note: Marking this for stable on v3.4+ kernels, but kernels as old as
v2.6.38 may have a similar problem and may need similar fix]
Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru> Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
For avr32 cross compiler, do not define '__linux__' internally, so it
will cause issue with allmodconfig.
The related error:
CC [M] fs/coda/psdev.o
In file included from include/linux/coda.h:64,
from fs/coda/psdev.c:45:
include/uapi/linux/coda.h:221: error: expected specifier-qualifier-list before 'u_quad_t'
The related toolchain version (which only download, not re-compile):
In file included from arch/avr32/boards/mimc200/fram.c:13:
include/linux/miscdevice.h:51: error: field 'list' has incomplete type
include/linux/miscdevice.h:55: error: expected specifier-qualifier-list before 'mode_t'
arch/avr32/boards/mimc200/fram.c:42: error: 'THIS_MODULE' undeclared here (not in a function)
When doing reset in order to recover the affected PE, we issue
hot reset on PE primary bus if it's not root bus. Otherwise, we
issue hot or fundamental reset on root port or PHB accordingly.
For the later case, we didn't cover the situation where PE only
includes root port and it potentially causes kernel crash upon
EEH error to the PE.
The patch reworks the logic of EEH reset to improve the code
readability and also avoid the kernel crash.
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The reason is that we have used the wrong register to calculate the
ksp_limit in commit cbc9565ee826 (powerpc: Remove ksp_limit on ppc64).
Just fix it.
As suggested by Benjamin Herrenschmidt, also add the C prototype of the
function in the comment in order to avoid such kind of errors in the
future.
Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for ONENAND driver to probe later. However this does
not happen if generic MTD_ONENAND framework is built as module (CONFIG_MTD_ONENAND=m).
Therefore, when MTD/ONENAND and MTD/ONENAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
ONENAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_ONENAND=y || CONFIG_MTD_ONENAND=m
Fixes: commit bc6b1e7b86f5d8e4a6fc1c0189e64bba4077efe0
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for NAND driver to probe later. However this does
not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m).
Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
NAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m
Whilst the code does indeed reflect this in terms of the architecture,
the final <barrier> + <sev> have been contracted into a single inline
asm without a "memory" clobber, therefore the compiler is at liberty to
reorder the unlock to the end of the above sequence. In such a case,
a waiting CPU may be woken up before the lock has been unlocked, leading
to extremely poor performance.
This patch reworks the dsb_sev() function to make use of the dsb()
macro and ensure ordering against the unlock.
Reported-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
During __v{6,7}_setup, we invalidate the TLBs since we are about to
enable the MMU on return to head.S. Unfortunately, without a subsequent
dsb instruction, the invalidation is not guaranteed to have completed by
the time we write to the sctlr, potentially exposing us to junk/stale
translations cached in the TLB.
This patch reworks the init functions so that the dsb used to ensure
completion of cache/predictor maintenance is also used to ensure
completion of the TLB invalidation.
Reported-by: Albin Tonnerre <Albin.Tonnerre@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
GFP_ATOMIC is not a single gfp flag, but a macro which expands to the other
flags and LACK of __GFP_WAIT flag. To check if caller wanted to perform an
atomic allocation, the code must test __GFP_WAIT flag presence. This patch
fixes the issue introduced in v3.6-rc5
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The set_flexbg_block_bitmap() function assumed that the number of
blocks in a blockgroup was sb->blocksize * 8, which is normally true,
but not always! Use EXT4_BLOCKS_PER_GROUP(sb) instead, to fix block
bitmap corruption after:
If a file system has a large number of inodes per block group, all of
the metadata blocks in a flex_bg may be larger than what can fit in a
single block group. Unfortunately, ext4_alloc_group_tables() in
resize.c was never tested to see if it would handle this case
correctly, and there were a large number of bugs which caused the
following sequence to result in a BUG_ON:
To fix this, we need to make sure the right thing happens when a block
group's inode table straddles two block groups, which means the
following bugs had to be fixed:
1) Not clearing the BLOCK_UNINIT flag in the second block group in
ext4_alloc_group_tables --- the was proximate cause of the BUG_ON.
2) Incorrectly determining how many block groups contained contiguous
free blocks in ext4_alloc_group_tables().
3) Incorrectly setting the start of the next block range to be marked
in use after a discontinuity in setup_new_flex_group_blocks().
If an ext4 file system is created by some tool other than mke2fs
(perhaps by someone who has a pathalogical fear of the GPL) that
doesn't set one or the other of the EXT2_FLAGS_{UN}SIGNED_HASH flags,
and that file system is then mounted read-only, don't try to modify
the s_flags field. Otherwise, if dm_verity is in use, the superblock
will change, causing an dm_verity failure.
In swap_inode_boot_loader() we forgot to release ->i_mutex and resume
unlocked dio for inode and inode_bl if there is an error starting the
journal handle. This commit fixes this issue.
Reported-by: Ahmed Tamrawi <ahmedtamrawi@gmail.com> Cc: Andreas Dilger <adilger.kernel@dilger.ca> Cc: Dr. Tilmann Bubeck <t.bubeck@reinform.de> Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit a115f749c1 (ext4: remove wait for unwritten extent conversion from
ext4_truncate) exposed a bug in ext4_ext_handle_uninitialized_extents().
It can be triggered by xfstest generic/299 when run on a test file
system created without a journal. This test continuously fallocates and
truncates files to which random dio/aio writes are simultaneously
performed by a separate process. The test completes successfully, but
if the test filesystem is mounted with the block_validity option, a
warning message stating that a logical block has been mapped to an
illegal physical block is posted in the kernel log.
The bug occurs when an extent is being converted to the written state
by ext4_end_io_dio() and ext4_ext_handle_uninitialized_extents()
discovers a mapping for an existing uninitialized extent. Although it
sets EXT4_MAP_MAPPED in map->m_flags, it fails to set map->m_pblk to
the discovered physical block number. Because map->m_pblk is not
otherwise initialized or set by this function or its callers, its
uninitialized value is returned to ext4_map_blocks(), where it is
stored as a bogus mapping in the extent status tree.
Since map->m_pblk can accidentally contain illegal values that are
larger than the physical size of the file system, calls to
check_block_validity() in ext4_map_blocks() that are enabled if the
block_validity mount option is used can fail, resulting in the logged
warning message.
intel_ring_cachline_align() emits MI_NOOPs until the ring tail is
aligned to a cacheline boundary.
Cc: Bjoern C <lkml@call-home.ch> Cc: Alexandru DAMIAN <alexandru.damian@intel.com> Cc: Enrico Tagliavini <enrico.tagliavini@gmail.com> Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 0a0afd282f ("drm/nv50-/disp: move DP link training to core and
train from supervisor") added code that uses the wrong register for
computing the display bpp, used for bandwidth calculation. Adjust to use
the same register as used by exec_clkcmp and nv50_disp_intr_unk20_2_dp.
Reported-by: Torsten Wagner <torsten.wagner@gmail.com> Reported-by: Michael Gulick <mgulick@mathworks.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67628 Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since commit 0fa9061ae8c ("drm/nouveau/mc: handle irq-related setup
ourselves"), drm_device->irq_enabled remained unset. This is needed in
order to properly wait for a vblank event in the generic drm code.
See https://bugs.freedesktop.org/show_bug.cgi?id=74195
Reported-by: Jan Janecek <janjanjanx@gmail.com> Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch addresses a bug in bio_integrity_verify() code that has
been causing DIF READ verify operations to be silently skipped.
The issue is that bio->bi_idx will have been incremented within
bio_advance() code in the normal blk_update_request() ->
req_bio_endio() completion path, and bio_integrity_verify() is
using bio_for_each_segment() which starts the bio segment walk
at the current bio->bi_idx.
So instead use bio_for_each_segment_all() to always start the bio
segment walk from zero, regardless of the current bio->bi_idx
value after bio_advance() has been called.
(Context change for v3.10.y -> v3.13.y code - nab)
Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Cc: stable@kernel.dk # >= v3.10 Signed-off-by: Jens Axboe <axboe@kernel.dk>
On the Dell machines with codec whose Subsystem Id is 0x10280624,
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/bugs/1259790 Cc: David Henningsson <david.henningsson@canonical.com> Cc: stable@vger.kernel.org Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On the Dell Inspiron 3045 machine (codec Subsystem Id: 0x10280628),
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/hwe-somerville/+bug/1259437 CC: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
On the Dell Optiplex 3030 machine (codec Subsystem Id: 0x10280623),
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/hwe-somerville/+bug/1259435 CC: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
You're looking at a casual headset patch,
for a specific hardware it will match,
and suddenly, the headset jack will work,
so please apply this simple quirk!
Upon suspend / resume, the fixup register settings are lost because
sending HDA_FIXUP_ACT_PRE_PROBE is not part of the resume path. Instead,
write our registers in response to the HDA_FIXUP_ACT_INIT, which happens
after initial probe and upon resume.
ASUS N56VZ and N76VZ laptops have a bass speaker but its output comes
only from the right channel. This patch adds the extra chmap specific
to these models.
Commit aa9c2669626c (NFS: Client implementation of Labeled-NFS) introduces
a performance regression. When nfs_zap_caches_locked is called, it sets
the NFS_INO_INVALID_LABEL flag irrespectively of whether or not the
NFS server supports security labels. Since that flag is never cleared,
it means that all calls to nfs_revalidate_inode() will now trigger
an on-the-wire GETATTR call.
This patch ensures that we never set the NFS_INO_INVALID_LABEL unless the
server advertises support for labeled NFS.
It also causes nfs_setsecurity() to clear NFS_INO_INVALID_LABEL when it
has successfully set the security label for the inode.
Finally it gets rid of the NFS_INO_INVALID_LABEL cruft from nfs_update_inode,
which has nothing to do with labeled NFS.
Reported-by: Neil Brown <neilb@suse.de> Cc: stable@vger.kernel.org # 3.11+ Tested-by: Neil Brown <neilb@suse.de> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When using a mix of compressed file extents and prealloc extents, it
is possible to fill a page of a file with random, garbage data from
some unrelated previous use of the page, instead of a sequence of zeroes.
A simple sequence of steps to get into such case, taken from the test
case I made for xfstests, is:
This results in the following file items in the fs tree:
item 4 key (257 INODE_ITEM 0) itemoff 15879 itemsize 160
inode generation 6 transid 6 size 542872 block group 0 mode 100600
item 5 key (257 INODE_REF 256) itemoff 15863 itemsize 16
inode ref index 2 namelen 6 name: foobar
item 6 key (257 EXTENT_DATA 0) itemoff 15810 itemsize 53
extent data disk byte 0 nr 0 gen 6
extent data offset 0 nr 24576 ram 266240
extent compression 0
item 7 key (257 EXTENT_DATA 24576) itemoff 15757 itemsize 53
prealloc data disk byte 12849152 nr 241664 gen 6
prealloc data offset 0 nr 241664
item 8 key (257 EXTENT_DATA 266240) itemoff 15704 itemsize 53
extent data disk byte 12845056 nr 4096 gen 6
extent data offset 0 nr 20480 ram 20480
extent compression 2
item 9 key (257 EXTENT_DATA 286720) itemoff 15651 itemsize 53
prealloc data disk byte 13090816 nr 405504 gen 6
prealloc data offset 0 nr 258048
The on disk extent at offset 266240 (which corresponds to 1 single disk block),
contains 5 compressed chunks of file data. Each of the first 4 compress 4096
bytes of file data, while the last one only compresses 3024 bytes of file data.
Therefore a read into the file region [285648 ; 286720[ (length = 4096 - 3024 =
1072 bytes) should always return zeroes (our next extent is a prealloc one).
The solution here is the compression code path to zero the remaining (untouched)
bytes of the last page it uncompressed data into, as the information about how
much space the file data consumes in the last page is not known in the upper layer
fs/btrfs/extent_io.c:__do_readpage(). In __do_readpage we were correctly zeroing
the remainder of the page but only if it corresponds to the last page of the inode
and if the inode's size is not a multiple of the page size.
This would cause not only returning random data on reads, but also permanently
storing random data when updating parts of the region that should be zeroed.
For the example above, it means updating a single byte in the region [285648 ; 286720[
would store that byte correctly but also store random data on disk.
A test case for xfstests follows soon.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
While running the test btrfs/004 from xfstests in a loop, it failed
about 1 time out of 20 runs in my desktop. The failure happened in
the backref walking part of the test, and the test's error message was
like this:
btrfs/004 93s ... [failed, exit status 1] - output mismatch (see /home/fdmanana/git/hub/xfstests_2/results//btrfs/004.out.bad)
--- tests/btrfs/004.out 2013-11-26 18:25:29.263333714 +0000
+++ /home/fdmanana/git/hub/xfstests_2/results//btrfs/004.out.bad 2013-12-10 15:25:10.327518516 +0000
@@ -1,3 +1,8 @@
QA output created by 004
*** test backref walking
-*** done
+unexpected output from
+ /home/fdmanana/git/hub/btrfs-progs/btrfs inspect-internal logical-resolve -P 141512704 /home/fdmanana/btrfs-tests/scratch_1
+expected inum: 405, expected address: 454656, file: /home/fdmanana/btrfs-tests/scratch_1/snap1/p0/d6/d3d/d156/fce, got:
+
...
(Run 'diff -u tests/btrfs/004.out /home/fdmanana/git/hub/xfstests_2/results//btrfs/004.out.bad' to see the entire diff)
Ran: btrfs/004
Failures: btrfs/004
Failed 1 of 1 tests
But immediately after the test finished, the btrfs inspect-internal command
returned the expected output:
It turned out this was because the btrfs_search_old_slot() calls performed
during backref walking (backref.c:__resolve_indirect_ref) were not finding
anything. The reason for this turned out to be that the tree mod logging
code was not logging some node multi-step operations atomically, therefore
btrfs_search_old_slot() callers iterated often over an incomplete tree that
wasn't fully consistent with any tree state from the past. Besides missing
items, this often (but not always) resulted in -EIO errors during old slot
searches, reported in dmesg like this:
These tree mod log operations that must be performed atomically, tree_mod_log_free_eb,
tree_mod_log_eb_copy, tree_mod_log_insert_root and tree_mod_log_insert_move, used to
be performed atomically before the following commit:
That change removed the atomicity of such operations. This patch restores the
atomicity while still not doing the GFP_ATOMIC allocations of tree_mod_elem
structures, so it has to do the allocations using GFP_NOFS before acquiring
the mod log lock.
This issue has been experienced by several users recently, such as for example:
After running the btrfs/004 test for 679 consecutive iterations with this
patch applied, I didn't ran into the issue anymore.
Cc: stable@vger.kernel.org Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In ctree.c:tree_mod_log_set_node_key() we were calling
__tree_mod_log_insert_key() even when the modification doesn't need
to be logged. This would allocate a tree_mod_elem structure, fill it
and pass it to __tree_mod_log_insert(), which would just acquire
the tree mod log write lock and then free the tree_mod_elem structure
and return (that is, a no-op).
Therefore call tree_mod_log_insert() instead of __tree_mod_log_insert()
which just returns immediately if the modification doesn't need to be
logged (without allocating the structure, fill it, acquire write lock,
free structure).
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
sock_alloc_send_pskb() & sk_page_frag_refill()
have a loop trying high order allocations to prepare
skb with low number of fragments as this increases performance.
Problem is that under memory pressure/fragmentation, this can
trigger OOM while the intent was only to try the high order
allocations, then fallback to order-0 allocations.
We had various reports from unexpected regressions.
According to David, setting __GFP_NORETRY should be fine,
as the asynchronous compaction is still enabled, and this
will prevent OOM from kicking as in :
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: David Rientjes <rientjes@google.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Marcelo Ricardo Leitner reported problems when the forwarding link path
has a lower mtu than the incoming one if the inbound interface supports GRO.
Given:
Host <mtu1500> R1 <mtu1200> R2
Host sends tcp stream which is routed via R1 and R2. R1 performs GRO.
In this case, the kernel will fail to send ICMP fragmentation needed
messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu
checks in forward path. Instead, Linux tries to send out packets exceeding
the mtu.
When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does
not fragment the packets when forwarding, and again tries to send out
packets exceeding R1-R2 link mtu.
This alters the forwarding dstmtu checks to take the individual gso
segment lengths into account.
For ipv6, we send out pkt too big error for gso if the individual
segments are too big.
For ipv4, we either send icmp fragmentation needed, or, if the DF bit
is not set, perform software segmentation and let the output path
create fragments when the packet is leaving the machine.
It is not 100% correct as the error message will contain the headers of
the GRO skb instead of the original/segmented one, but it seems to
work fine in my (limited) tests.
Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid
sofware segmentation.
However it turns out that skb_segment() assumes skb nr_frags is related
to mss size so we would BUG there. I don't want to mess with it considering
Herbert and Eric disagree on what the correct behavior should be.
Hannes Frederic Sowa notes that when we would shrink gso_size
skb_segment would then also need to deal with the case where
SKB_MAX_FRAGS would be exceeded.
This uses sofware segmentation in the forward path when we hit ipv4
non-DF packets and the outgoing link mtu is too small. Its not perfect,
but given the lack of bug reports wrt. GRO fwd being broken this is a
rare case anyway. Also its not like this could not be improved later
once the dust settles.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This moves part of Eric Dumazets skb_gso_seglen helper from tbf sched to
skbuff core so it may be reused by upcoming ip forwarding path patch.
Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
SCTP's sctp_connectx() abi breaks for 64bit kernels compiled with 32bit
emulation (e.g. ia32 emulation or x86_x32). Due to internal usage of
'struct sctp_getaddrs_old' which includes a struct sockaddr pointer,
sizeof(param) check will always fail in kernel as the structure in
64bit kernel space is 4bytes larger than for user binaries compiled
in 32bit mode. Thus, applications making use of sctp_connectx() won't
be able to run under such circumstances.
Introduce a compat interface in the kernel to deal with such
situations by using a 'struct compat_sctp_getaddrs_old' structure
where user data is copied into it, and then sucessively transformed
into a 'struct sctp_getaddrs_old' structure with the help of
compat_ptr(). That fixes sctp_connectx() abi without any changes
needed in user space, and lets the SCTP test suite pass when compiled
in 32bit and run on 64bit kernels.
Fixes: f9c67811ebc0 ("sctp: Fix regression introduced by new sctp_connectx api") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
since commit 89aef8921bf("ipv4: Delete routing cache."), the counter
in_slow_tot can't work correctly.
The counter in_slow_tot increase by one when fib_lookup() return successfully
in ip_route_input_slow(), but actually the dst struct maybe not be created and
cached, so we can increase in_slow_tot after the dst struct is created.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Acked-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com> Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com> Reported-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
vhost checked the counter within the refcnt before decrementing. It
really wanted to know that it is the one that has the last reference, as
a way to batch freeing resources a bit more efficiently.
Note: we only let refcount go to 0 on device release.
This works well but we now access the ref counter twice so there's a
race: all users might see a high count and decide to defer freeing
resources.
In the end no one initiates freeing resources until the last reference
is gone (which is on VM shotdown so might happen after a looooong time).
Let's do what we probably should have done straight away:
switch from kref to plain atomic, documenting the
semantics, return the refcount value atomically after decrement,
then use that to avoid the deadlock.
Reported-by: Qin Chuanyu <qinchuanyu@huawei.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <david.vrabel@citrix.com> Tested-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 46d3ceabd8d9 ("tcp: TCP Small Queues") introduced a possible
regression for applications using TCP_NODELAY.
If TCP session is throttled because of tsq, we should consult
tp->nonagle when TX completion is done and allow us to send additional
segment, especially if this segment is not a full MSS.
Otherwise this segment is sent after an RTO.
[edumazet] : Cooked the changelog, added another fix about testing
sk_wmem_alloc twice because TX completion can happen right before
setting TSQ_THROTTLED bit.
This problem is particularly visible with recent auto corking,
but might also be triggered with low tcp_limit_output_bytes
values or NIC drivers delaying TX completion by hundred of usec,
and very low rtt.
Thomas Glanzmann for example reported an iscsi regression, caused
by tcp auto corking making this bug quite visible.
Fixes: 46d3ceabd8d9 ("tcp: TCP Small Queues") Signed-off-by: John Ogness <john.ogness@linutronix.de> Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Thomas Glanzmann <thomas@glanzmann.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This device was mentioned in an OpenWRT forum. Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
0: qcdm
2: nmea
3: modem
8: qmi
9: storage
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently, to make netconsole start over IPv6, the source address
needs to be specified. Without a source address, netpoll_parse_options
assumes we're setting up over IPv4 and the destination IPv6 address is
rejected.
Check if the IP version has been forced by a source address before
checking for a version mismatch when parsing the destination address.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
ip rules with iif/oif references do not update:
(detach/attach) across interface renames.
Signed-off-by: Maciej Żenczykowski <maze@google.com> CC: Willem de Bruijn <willemb@google.com> CC: Eric Dumazet <edumazet@google.com> CC: Chris Davis <chrismd@google.com> CC: Carlo Contavalli <ccontavalli@google.com>
Google-Bug-Id: 12936021 Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Apparently commit 5c766d642bcaffd0c2a5b354db2068515b3846cf ("ipv4:
introduce address lifetime") forgot to take into account the addition of
struct ifa_cacheinfo in inet_nlmsg_size(). Hence add it, like is already
done for ipv6.
Suggested-by: Cong Wang <cwang@twopensource.com> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / thirdparty / kernel / stable.git / log
