When smb2 leases is disable, ksmbd can send oplock break notification
and cause wait oplock break ack timeout. It may appear like hang when
accessing a directory. This patch make only v2 leases handle the
directory.
Cc: stable@vger.kernel.org Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race is between the handling of a new TCP connection and
its disconnection. It leads to UAF on `struct tcp_transport` in
ksmbd_tcp_new_connection() function.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-22991 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.
Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before uart_get_rs485_mode() gets
called.
Also replace the assignment of rs485_config() to have the complete RS485
setup in one function.
Fixes: e2752ae3cfc9 ("serial: omap: Disallow RS-485 if rts-gpio is not specified") Cc: <stable@vger.kernel.org> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240103061818.564-7-l.sanfilippo@kunbus.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986e6 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way") Cc: stable <stable@kernel.org> Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Reviewed-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.
This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.
Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.
With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.
Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.
The commit fcc446c8aa63 ("serial: 8250_bcm2835aux: Add ACPI support")
dropped the error handling for clock acquiring. But even an optional
clock needs this.
If the RS485 feature RX-during-TX is supported by means of a GPIO set the
according supported flag. Otherwise setting this feature from userspace may
not be possible, since in uart_sanitize_serial_rs485() the passed RS485
configuration is matched against the supported features and unsupported
settings are thereby removed and thus take no effect.
Cc: <stable@vger.kernel.org> Fixes: 163f080eb717 ("serial: core: Add option to output RS485 RX_DURING_TX state via GPIO") Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Link: https://lore.kernel.org/r/20240103061818.564-3-l.sanfilippo@kunbus.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some uart drivers specify a rs485_config() function and then decide later
to disable RS485 support for some reason (e.g. imx and ar933).
In these cases userspace may be able to activate RS485 via TIOCSRS485
nevertheless, since in uart_set_rs485_config() an existing rs485_config()
function indicates that RS485 is supported.
Make sure that this is not longer possible by checking the uarts
rs485_supported.flags instead and bailing out if SER_RS485_ENABLED is not
set.
Furthermore instead of returning an empty structure return -ENOTTY if the
RS485 configuration is requested via TIOCGRS485 but RS485 is not supported.
This has a small impact on userspace visibility but it is consistent with
the -ENOTTY error for TIOCGRS485.
Among other things uart_sanitize_serial_rs485() tests the sanity of the RTS
settings in a RS485 configuration that has been passed by userspace.
If RTS-on-send and RTS-after-send are both set or unset the configuration
is adjusted and RTS-after-send is disabled and RTS-on-send enabled.
This however makes only sense if both RTS modes are actually supported by
the driver.
With commit be2e2cb1d281 ("serial: Sanitize rs485_struct") the code does
take the driver support into account but only checks if one of both RTS
modes are supported. This may lead to the errorneous result of RTS-on-send
being set even if only RTS-after-send is supported.
Fix this by changing the implemented logic: First clear all unsupported
flags in the RS485 configuration, then adjust an invalid RTS setting by
taking into account which RTS mode is supported.
Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
Since this function is called with the port lock held, this can be a
problem in case that setting the GPIO line can sleep (e.g. if a GPIO
expander is used which is connected via SPI or I2C).
Avoid this issue by moving the GPIO setting outside of the port lock into
the serial core and thus making it a generic feature.
Also with commit c54d48543689 ("serial: stm32: Add support for rs485
RX_DURING_TX output GPIO") the SER_RS485_RX_DURING_TX flag is only set if a
rx-during-tx GPIO is _not_ available, which is wrong. Fix this, too.
Furthermore reset old GPIO settings in case that changing the RS485
configuration failed.
In mon_bin_vma_fault():
offset = vmf->pgoff << PAGE_SHIFT;
if (offset >= rp->b_size)
return VM_FAULT_SIGBUS;
chunk_idx = offset / CHUNK_SIZE;
pageptr = rp->b_vec[chunk_idx].pg;
The code is executed without holding any lock.
In mon_bin_vma_close():
spin_lock_irqsave(&rp->b_lock, flags);
rp->mmap_active--;
spin_unlock_irqrestore(&rp->b_lock, flags);
Concurrent execution of mon_bin_vma_fault() with mon_bin_vma_close() and
mon_bin_ioctl() could lead to atomicity violations. mon_bin_vma_fault()
accesses rp->b_size and rp->b_vec without locking, risking array
out-of-bounds access or use-after-free bugs due to possible modifications
in mon_bin_ioctl().
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 6.2.
To address this issue, it is proposed to add a spin lock pair in
mon_bin_vma_fault() to ensure atomicity. With this patch applied, our tool
never reports the possible bug, with the kernel configuration allyesconfig
for x86_64. Due to the lack of associated hardware, we cannot test the
patch in runtime testing, and just verify it according to the code logic.
[1] https://sites.google.com/view/basscheck/
Fixes: 19e6317d24c2 ("usb: mon: Fix a deadlock in usbmon between ...") Cc: <stable@vger.kernel.org> Signed-off-by: Gui-Dong Han <2045gemini@gmail.com> Link: https://lore.kernel.org/r/20240105052412.9377-1-2045gemini@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released is a plug evaluates
against the released altmode's partner instead of the calling altmode, so
change adev in typec_altmode_put_partner to properly refer to the altmode
being released.
Because typec_altmode_set_partner calls get_device() on the port altmode,
add partner_adev that points to the port altmode in typec_put_partner to
call put_device() on. typec_altmode_set_partner is not called for port
altmodes, so add a check in typec_altmode_release to prevent
typec_altmode_put_partner() calls on port altmode release.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes") Cc: <stable@vger.kernel.org> Co-developed-by: Christian A. Ehrhardt <lk@c--e.de> Signed-off-by: Christian A. Ehrhardt <lk@c--e.de> Signed-off-by: RD Babiera <rdbabiera@google.com> Tested-by: Christian A. Ehrhardt <lk@c--e.de> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20240103181754.2492492-2-rdbabiera@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.
Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...
The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...
To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.
ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n
CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.
According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)
Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.
Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.
When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.
But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.
The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.
Fixed it by below major steps:
1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.
.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB, LINK_TRB ... LINK_TRB
^End of TRB List
After the chipidea driver introduce extcon for id and vbus, it's able
to wakeup from another irq source, in case the system with extcon ID
cable, wakeup from usb ID cable and device removal, the usb device
disconnect irq may come firstly before the extcon notifier while system
resume, so we will get 2 "wakeup" irq, one for usb device disconnect;
and one for extcon ID cable change(real wakeup event), current driver
treat them as 2 successive wakeup irq so can't handle it correctly, then
finally the usb irq can't be enabled. This patch adds a check to bypass
further usb events before controller resume finished to fix it.
Fixes: 1f874edcb731 ("usb: chipidea: add runtime power management support")
cc: <stable@vger.kernel.org> Acked-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Link: https://lore.kernel.org/r/20231228110753.1755756-2-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't omit soft-reset. During initialization, the driver may need to
perform a soft reset to ensure the phy is ready when the controller
updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset.
Many platforms often have access to DCTL register for soft-reset despite
being host-only. If there are actual reported issues from the platforms
that don't expose DCTL registers, then we will need to revisit (perhaps
to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST).
There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.
The exact condition is seen with the following sequence:
1. USB bus reset is issued by the host
2. Shortly after, or concurrently, a USB PD DR SWAP request is received
(sink->source)
3. USB bus reset event handler runs and issues
dwc3_stop_active_transfers(), and pending transfer are stopped
4. DWC3 usage_count decremented to 0, and runtime idle occurs while
dwc->connected == true, returns -EBUSY
5. DWC3 disconnect event seen, dwc->connected set to false due to DR
swap handling
6. No runtime idle after this point
Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.
Current EP0 dequeue path will share the same as other EPs. However, there
are some special considerations that need to be made for EP0 transfers:
- EP0 transfers never transition into the started_list
- EP0 only has one active request at a time
In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to. While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command. If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.
In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed. However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.
Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled. This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.
Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().
By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.
When CONFIG_USB_OTG is not set, mxs_phy_is_otg_host() will always return
false. This behaviour is wrong. Since phy.last_event will always be set
for either host or device mode. Therefore, CONFIG_USB_OTG condition
can be removed.
Fixes: 5eda42aebb76 ("usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()")
cc: <stable@vger.kernel.org> Acked-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20231228110753.1755756-3-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 6.7-rc1, there was a netif_device_detach call added to the
gether_disconnect function. This clears the __LINK_STATE_PRESENT bit of
the netif device and suppresses pings (ICMP messages) and TCP connection
requests from the connected host. If userspace temporarily disconnects
the gadget, such as by temporarily removing configuration in the gadget
configfs interface, network activity should continue to be processed
when the gadget is re-connected. Mirror the netif_device_detach call
with a netif_device_attach call in gether_connect to fix re-connecting
gadgets.
gadget_is_{super|dual}speed() API check UDC controller capitblity. It
should pass down highest speed endpoint descriptor to UDC controller. So
UDC controller driver can reserve enough resource at check_config(),
especially mult and maxburst. So UDC driver (such as cdns3) can know need
at least (mult + 1) * (maxburst + 1) * wMaxPacketSize internal memory for
this uvc functions.
Reason for this is that get_idle_time() in fs/proc/stat.c has different
sources for both values depending on if a CPU is online or offline:
- if a CPU is online the values may be taken from its per cpu
tick_cpu_sched structure
- if a CPU is offline the values are taken from its per cpu cpustat
structure
The problem is that the per cpu tick_cpu_sched structure is set to zero on
CPU offline. See tick_cancel_sched_timer() in kernel/time/tick-sched.c.
Therefore when a CPU is brought offline and online afterwards both its idle
and iowait sleeptime will be zero, causing a jump backward in total system
idle and iowait sleeptime. In a similar way if a CPU is then brought
offline again the total idle and iowait sleeptimes will jump forward.
It looks like this behavior was introduced with commit 4b0c0f294f60
("tick: Cleanup NOHZ per cpu data on cpu down").
This was only noticed now on s390, since we switched to generic idle time
reporting with commit be76ea614460 ("s390/idle: remove arch_cpu_idle_time()
and corresponding code").
Fix this by preserving the values of idle_sleeptime and iowait_sleeptime
members of the per-cpu tick_sched structure on CPU hotplug.
Fixes: 4b0c0f294f60 ("tick: Cleanup NOHZ per cpu data on cpu down") Reported-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20240115163555.1004144-1-hca@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are reports of kernels crashing due to stack overflow while
running OpenShift (Kubernetes). The primary contributor to the stack
usage seems to be openvswitch, which is used by OVN-Kubernetes (based on
OVN (Open Virtual Network)), but NFS also contributes in some stack
traces.
There may be some opportunities to reduce stack usage in the openvswitch
code, but doing so potentially require tradeoffs vs performance, and
also requires testing across architectures.
Looking at stack usage across the kernel (using -fstack-usage), shows
that ppc64le stack frames are on average 50-100% larger than the
equivalent function built for x86-64. Which is not surprising given the
minimum stack frame size is 32 bytes on ppc64le vs 16 bytes on x86-64.
So increase the default stack size to 32KB for the modern 64-bit Book3S
platforms, ie. pseries (virtualised) and powernv (bare metal). That
leaves the older systems like G5s, and the AmigaOne (pasemi) with a 16KB
stack which should be sufficient on those machines.
When the interrupt property fails to be parsed, ep93xx_timer_of_init()
return code ends up uninitialized:
drivers/clocksource/timer-ep93xx.c:160:6: error: variable 'ret' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (irq < 0) {
^~~~~~~
drivers/clocksource/timer-ep93xx.c:188:9: note: uninitialized use occurs here
return ret;
^~~
drivers/clocksource/timer-ep93xx.c:160:2: note: remove the 'if' if its condition is always false
if (irq < 0) {
^~~~~~~~~~~~~~
Simplify this portion to use the normal construct of just checking
whether a valid interrupt was returned. Note that irq_of_parse_and_map()
never returns a negative value and no other callers check for that either.
The timer registers of aclint don't follow the clint layout and can
be mapped on any different offset. As sg2042 uses separated timer
and mswi for its clint, it should follow the aclint spec and have
separated registers.
The previous patch introduced a new type of T-HEAD aclint timer which
has clint timer layout. Although it has the clint timer layout, it
should follow the aclint spec and uses the separated mtime and mtimecmp
regs. So a ABI change is needed to make the timer fit the aclint spec.
To make T-HEAD aclint timer more closer to the aclint spec, use
regs-names to represent the mtimecmp register, which can avoid hack
for unsupport mtime register of T-HEAD aclint timer.
Also, as T-HEAD aclint only supports mtimecmp, it is unnecessary to
implement the whole aclint spec. To make this binding T-HEAD specific,
only add reg-name for existed register. For details, see the discussion
in the last link.
Task A calls binder_update_page_range() to allocate and insert pages on
a remote address space from Task B. For this, Task A pins the remote mm
via mmget_not_zero() first. This can race with Task B do_exit() and the
final mmput() refcount decrement will come from Task A.
In this case, the work of ____fput() from Task B is queued up in Task A
as TWA_RESUME. So in theory, Task A returns to userspace and the cleanup
work gets executed. However, Task A instead sleep, waiting for a reply
from Task B that never comes (it's dead).
This means the binder_deferred_release() is blocked until an unrelated
binder event forces Task A to go back to userspace. All the associated
death notifications will also be delayed until then.
In order to fix this use mmput_async() that will schedule the work in
the corresponding mm->async_put_work WQ instead of Task A.
While frontends may submit zero-size requests (wasting a precious slot),
core networking code as of at least 3ece782693c4b ("sock: skb_copy_ubufs
support for compound pages") can't deal with SKBs when they have all
zero-size fragments. Respond to empty requests right when populating
fragments; all further processing is fragment based and hence won't
encounter these empty requests anymore.
In a way this should have been that way from the beginning: When no data
is to be transferred for a particular request, there's not even a point
in validating the respective grant ref. That's no different from e.g.
passing NULL into memcpy() when at the same time the size is 0.
This is XSA-448 / CVE-2023-46838.
Cc: stable@vger.kernel.org Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That commit causes NULL pointer dereferences in dmesgs when
running applications using ROCm, including clinfo, blender,
and PyTorch, since v6.6.1. Revert it to fix blender again.
Neither bindgen nor Rust know about the preserve-most calling
convention, and Clang describes it as unstable. Since we aren't using
functions with this calling convention from Rust, blocklist them.
These functions are only added to the build when list hardening is
enabled, which is likely why others didn't notice this yet.
Signed-off-by: Matthew Maurer <mmaurer@google.com> Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com> Reviewed-by: Alice Ryhl <aliceryhl@google.com> Link: https://lore.kernel.org/r/20231031201945.1412345-1-mmaurer@google.com
[ Used Markdown for consistency with the other comments in the file. ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Barnabás reported that the change to skip the getid command
when the controller is in translated mode on laptops caused
the Version field of his "AT Translated Set 2 keyboard"
input device to change from ab83 to abba, breaking a custom
hwdb entry for this keyboard.
Use the standard ab83 id for keyboards when getid is skipped
(rather then that getid fails) to avoid reporting a different
Version to userspace then before skipping the getid.
Each transaction is associated with a 'struct binder_buffer' that stores
the metadata about its buffer area. Since commit 74310e06be4d ("android:
binder: Move buffer out of area shared with user space") this struct is
no longer embedded within the buffer itself but is instead allocated on
the heap to prevent userspace access to this driver-exclusive info.
Unfortunately, the space of this struct is still being accounted for in
the total buffer size calculation, specifically for async transactions.
This results in an additional 104 bytes added to every async buffer
request, and this area is never used.
This wasted space can be substantial. If we consider the maximum mmap
buffer space of SZ_4M, the driver will reserve half of it for async
transactions, or 0x200000. This area should, in theory, accommodate up
to 262,144 buffers of the minimum 8-byte size. However, after adding
the extra 'sizeof(struct binder_buffer)', the total number of buffers
drops to only 18,724, which is a sad 7.14% of the actual capacity.
This patch fixes the buffer size calculation to enable the utilization
of the entire async buffer space. This is expected to reduce the number
of -ENOSPC errors that are seen on the field.
Fixes: 74310e06be4d ("android: binder: Move buffer out of area shared with user space") Signed-off-by: Carlos Llamas <cmllamas@google.com> Reviewed-by: Alice Ryhl <aliceryhl@google.com> Link: https://lore.kernel.org/r/20231201172212.1813387-6-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the padding of 0-sized buffers to an earlier stage to account for
this round up during the alloc->free_async_space check.
Fixes: 74310e06be4d ("android: binder: Move buffer out of area shared with user space") Reviewed-by: Alice Ryhl <aliceryhl@google.com> Signed-off-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20231201172212.1813387-5-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit converted kernfs_idr_lock to an IRQ-safe raw_spinlock because it
could be acquired while holding an rq lock through bpf_cgroup_from_id().
However, kernfs_idr_lock is held while doing GPF_NOWAIT allocations which
involves acquiring an non-IRQ-safe and non-raw lock leading to the following
lockdep warning:
=============================
[ BUG: Invalid wait context ] 6.7.0-rc5-kzm9g-00251-g655022a45b1c #578 Not tainted
-----------------------------
swapper/0/0 is trying to lock: dfbcd488 (&c->lock){....}-{3:3}, at: local_lock_acquire+0x0/0xa4
other info that might help us debug this:
context-{5:5}
2 locks held by swapper/0/0:
#0: dfbc9c60 (lock){+.+.}-{3:3}, at: local_lock_acquire+0x0/0xa4
#1: c0c012a8 (kernfs_idr_lock){....}-{2:2}, at: __kernfs_new_node.constprop.0+0x68/0x258
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.7.0-rc5-kzm9g-00251-g655022a45b1c #578
Hardware name: Generic SH73A0 (Flattened Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x90
dump_stack_lvl from __lock_acquire+0x3cc/0x168c
__lock_acquire from lock_acquire+0x274/0x30c
lock_acquire from local_lock_acquire+0x28/0xa4
local_lock_acquire from ___slab_alloc+0x234/0x8a8
___slab_alloc from __slab_alloc.constprop.0+0x30/0x44
__slab_alloc.constprop.0 from kmem_cache_alloc+0x7c/0x148
kmem_cache_alloc from radix_tree_node_alloc.constprop.0+0x44/0xdc
radix_tree_node_alloc.constprop.0 from idr_get_free+0x110/0x2b8
idr_get_free from idr_alloc_u32+0x9c/0x108
idr_alloc_u32 from idr_alloc_cyclic+0x50/0xb8
idr_alloc_cyclic from __kernfs_new_node.constprop.0+0x88/0x258
__kernfs_new_node.constprop.0 from kernfs_create_root+0xbc/0x154
kernfs_create_root from sysfs_init+0x18/0x5c
sysfs_init from mnt_init+0xc4/0x220
mnt_init from vfs_caches_init+0x6c/0x88
vfs_caches_init from start_kernel+0x474/0x528
start_kernel from 0x0
Let's rever the commit. It's undesirable to spread out raw spinlock usage
anyway and the problem can be solved by protecting the lookup path with RCU
instead.
bpf_cgroup_from_id() is basically a wrapper to cgroup_get_from_id(),
that is relying on kernfs to determine the right cgroup associated to
the target id.
As a kfunc, it has the potential to be attached to any function through
BPF, particularly in contexts where certain locks are held.
However, kernfs is not using an irq safe spinlock for kernfs_idr_lock,
that means any kernfs function that is acquiring this lock can be
interrupted and potentially hit bpf_cgroup_from_id() in the process,
triggering a deadlock.
For example, it is really easy to trigger a lockdep splat between
kernfs_idr_lock and rq->_lock, attaching a small BPF program to
__set_cpus_allowed_ptr_locked() that just calls bpf_cgroup_from_id():
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
6.7.0-rc7-virtme #5 Not tainted
-----------------------------------------------------
repro/131 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: ffffffffb2dc4578 (kernfs_idr_lock){+.+.}-{2:2}, at: kernfs_find_and_get_node_by_id+0x1d/0x80
and this task is already holding: ffff911cbecaf218 (&rq->__lock){-.-.}-{2:2}, at: task_rq_lock+0x50/0xc0
which would create a new lock dependency:
(&rq->__lock){-.-.}-{2:2} -> (kernfs_idr_lock){+.+.}-{2:2}
but this new dependency connects a HARDIRQ-irq-safe lock:
(&rq->__lock){-.-.}-{2:2}
Prevent this deadlock condition converting kernfs_idr_lock to a raw irq
safe spinlock.
The performance impact of this change should be negligible and it also
helps to prevent similar deadlock conditions with any other subsystems
that may depend on kernfs.
The lock_class_key is still registered and can be found in
lock_keys_hash hlist after subsys_private is freed in error
handler path.A task who iterate over the lock_keys_hash
later may cause use-after-free.So fix that up and unregister
the lock_class_key before kfree(cp).
On our platform, a driver fails to kset_register because of
creating duplicate filename '/class/xxx'.With Kasan enabled,
it prints a invalid-access bug report.
KASAN bug report:
BUG: KASAN: invalid-access in lockdep_register_key+0x19c/0x1bc
Write of size 8 at addr 15ffff808b8c0368 by task modprobe/252
Pointer tag: [15], memory tag: [fe]
CPU: 7 PID: 252 Comm: modprobe Tainted: G W
6.6.0-mainline-maybe-dirty #1
Call trace:
dump_backtrace+0x1b0/0x1e4
show_stack+0x2c/0x40
dump_stack_lvl+0xac/0xe0
print_report+0x18c/0x4d8
kasan_report+0xe8/0x148
__hwasan_store8_noabort+0x88/0x98
lockdep_register_key+0x19c/0x1bc
class_register+0x94/0x1ec
init_module+0xbc/0xf48 [rfkill]
do_one_initcall+0x17c/0x72c
do_init_module+0x19c/0x3f8
...
Memory state around the buggy address: ffffff808b8c0100: 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a ffffff808b8c0200: 8a 8a 8a 8a 8a 8a 8a 8a fe fe fe fe fe fe fe fe
>ffffff808b8c0300: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
^ ffffff808b8c0400: 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03
As CONFIG_KASAN_GENERIC is not set, Kasan reports invalid-access
not use-after-free here.In this case, modprobe is manipulating
the corrupted lock_keys_hash hlish where lock_class_key is already
freed before.
It's worth noting that this only can happen if lockdep is enabled,
which is not true for normal system.
Fixes: dcfbb67e48a2 ("driver core: class: use lock_class_key already present in struct subsys_private") Cc: stable <stable@kernel.org> Signed-off-by: Jing Xia <jing.xia@unisoc.com> Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com> Link: https://lore.kernel.org/r/20231220024603.186078-1-jing.xia@unisoc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous setting did not take into account the CSTN mode.
For the H_WAIT_2 bitfield (bits 0-7) of the LCDC Horizontal Configuration
Register (LCDCR), the IMX25RM manual states that:
In TFT mode, it specifies the number of SCLK periods between the end of
HSYNC and the beginning of OE signal, and the total delay time equals
(H_WAIT_2 + 3) of SCLK periods.
In CSTN mode, it specifies the number of SCLK periods between the end of
HSYNC and the first display data in each line, and the total delay time
equals (H_WAIT_2 + 2) of SCLK periods.
In of_parse_phandle_with_args_map() the inner loop that
iterates through the map entries calls of_node_put(new)
to free the reference acquired by the previous iteration
of the inner loop. This assumes that the value of "new" is
NULL on the first iteration of the inner loop.
Make sure that this is true in all iterations of the outer
loop by setting "new" to NULL after its value is assigned to "cur".
Extend the unittest to detect the double free and add an additional
test case that actually triggers this path.
Fixes: bd6f2fd5a1 ("of: Support parsing phandle argument lists through a nexus node") Cc: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de> Link: https://lore.kernel.org/r/20231229105411.1603434-1-lk@c--e.de Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SMB2 Protocol requires that "The first byte of the Direct TCP
transport packet header MUST be zero (0x00)"[1]. Commit 1c1bcf2d3ea0
("ksmbd: validate smb request protocol id") removed the validation of
this 1-byte zero. Add the validation back now.
GCC 13.2.0 reported the warning of the print format specifier:
conf.c: In function ‘sysfs_get’:
conf.c:181:72: warning: format ‘%s’ expects argument of type ‘char *’, \
but argument 3 has type ‘int’ [-Wformat=]
181 | ksft_exit_fail_msg("sysfs: unable to read value '%s': %s\n",
| ~^
| |
| char *
| %d
The fix passes strerror(errno) as it was intended, like in the sibling error
exit message.
Fixes: aba51cd0949ae ("selftests: alsa - add PCM test") Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Shuah Khan <shuah@kernel.org> Cc: linux-sound@vger.kernel.org Cc: linux-kselftest@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20240107173704.937824-5-mirsad.todorovac@alu.unizg.hr Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The GCC 13.2.0 compiler issued the following warning:
mixer-test.c: In function ‘ctl_value_index_valid’:
mixer-test.c:322:79: warning: format ‘%lld’ expects argument of type ‘long long int’, \
but argument 5 has type ‘long int’ [-Wformat=]
322 | ksft_print_msg("%s.%d value %lld more than maximum %lld\n",
| ~~~^
| |
| long long int
| %ld
323 | ctl->name, index, int64_val,
324 | snd_ctl_elem_info_get_max(ctl->info));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| long int
Fixing the format specifier as advised by the compiler suggestion removes the
warning.
Fixes: 3f48b137d88e7 ("kselftest: alsa: Factor out check that values meet constraints") Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Shuah Khan <shuah@kernel.org> Cc: linux-sound@vger.kernel.org Cc: linux-kselftest@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20240107173704.937824-3-mirsad.todorovac@alu.unizg.hr Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Minor fix in the number of arguments to error reporting function in the
test program as reported by GCC 13.2.0 warning.
mixer-test.c: In function ‘find_controls’:
mixer-test.c:169:44: warning: too many arguments for format [-Wformat-extra-args]
169 | ksft_exit_fail_msg("snd_ctl_poll_descriptors() failed for %d\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The number of arguments in call to ksft_exit_fail_msg() doesn't correspond
to the format specifiers, so this is adjusted resembling the sibling calls
to the error function.
Fixes: b1446bda56456 ("kselftest: alsa: Check for event generation when we write to controls") Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Shuah Khan <shuah@kernel.org> Cc: linux-sound@vger.kernel.org Cc: linux-kselftest@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20240107173704.937824-2-mirsad.todorovac@alu.unizg.hr Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc prints a warning about a possible array overflow for a couple of
callers of dp_decide_lane_settings() after commit 1b56c90018f0 ("Makefile:
Enable -Wstringop-overflow globally"):
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c: In function 'dp_perform_fixed_vs_pe_training_sequence_legacy':
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: error: 'dp_decide_lane_settings' accessing 4 bytes in a region of size 1 [-Werror=stringop-overflow=]
426 | dp_decide_lane_settings(lt_settings, dpcd_lane_adjust,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
427 | lt_settings->hw_lane_settings, lt_settings->dpcd_lane_settings);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: note: referencing argument 4 of type 'union dpcd_training_lane[4]'
I'm not entirely sure what caused this, but changing the prototype to expect
a pointer instead of an array avoids the warnings.
Fixes: 7727e7b60f82 ("drm/amd/display: Improve robustness of FIXED_VS link training at DP1 rates") Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hwmgr->backend, (i.e. data) allocated by kzalloc is not freed in
the error-handling paths of smu7_get_evv_voltages and
smu7_update_edc_leakage_table. However, it did be freed in the
error-handling of phm_initializa_dynamic_state_adjustment_rule_settings,
by smu7_hwmgr_backend_fini. So the lack of free in smu7_get_evv_voltages
and smu7_update_edc_leakage_table is considered a memleak in this patch.
Fixes: 599a7e9fe1b6 ("drm/amd/powerplay: implement smu7 hwmgr to manager asics with smu ip version 7.") Fixes: 8f0804c6b7d0 ("drm/amd/pm: add edc leakage controller setting") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before using list_first_entry, make sure to check that list is not
empty, if list is empty return -ENODATA.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1347 kfd_create_indirect_link_prop() warn: can 'gpu_link' even be NULL?
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1428 kfd_add_peer_prop() warn: can 'iolink1' even be NULL?
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1433 kfd_add_peer_prop() warn: can 'iolink2' even be NULL?
Fixes: 0f28cca87e9a ("drm/amdkfd: Extend KFD device topology to surface peer-to-peer links") Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com> Suggested-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The iser_reg_resources structure has two pointers to MR but only one
mr_valid field. The implementation assumes that we use only *sig_mr when
pi_enable is true. Otherwise, we use only *mr. However, it is only
sometimes correct. Read commands without protection information occur even
when pi_enble is true. For example, the following SCSI commands have a
Data-In buffer but never have protection information: READ CAPACITY (16),
INQUIRY, MODE SENSE(6), MAINTENANCE IN. So, we use
*sig_mr for some SCSI commands and *mr for the other SCSI commands.
In most cases, it works fine because the remote invalidation is applied.
However, there are two cases when the remote invalidation is not
applicable.
1. Small write commands when all data is sent as an immediate.
2. The target does not support the remote invalidation feature.
The lazy invalidation is used if the remote invalidation is impossible.
Since, at the lazy invalidation, we always invalidate the MR we want to
use, the wrong MR may be invalidated.
To fix the issue, we need a field per MR that indicates the MR needs
invalidation. Since the ib_mr structure already has such a field, let's
use ib_mr.need_inval instead of iser_reg_resources.mr_valid.
Fixes: b76a439982f8 ("IB/iser: Use IB_WR_REG_MR_INTEGRITY for PI handover") Link: https://lore.kernel.org/r/20231219072311.40989-1-sergeygo@nvidia.com Acked-by: Max Gurtovoy <mgurtovoy@nvidia.com> Signed-off-by: Sergey Gorenko <sergeygo@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sdhci_omap is specific to older TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.
The sdhci_am654 is specific to recent TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.
Fixes: 41fd4caeb00b ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Link: https://lore.kernel.org/r/20231220135950.433588-1-pbrobinson@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure the value passed to scarlett2_mixer_ctl_put() is between 0 and
SCARLETT2_MIXER_MAX_VALUE so we don't attempt to access outside
scarlett2_mixer_values[].
scarlett2_usb_set_config() calls scarlett2_usb_get() but was not
checking the result. Return the error if it fails rather than
continuing with an invalid value.
scarlett2_config_save() was ignoring the return value from
scarlett2_usb(). As this function is not called from user-space we
can't return the error, so call usb_audio_err() instead.
dmi_platform_data[] first contains a DMI entry matching:
DMI_MATCH(DMI_PRODUCT_NAME, "EF20"),
and then contains an identical entry except for the match being:
DMI_MATCH(DMI_PRODUCT_NAME, "EF20EA"),
Since these are partial (non exact) DMI matches the first match
will also match any board with "EF20EA" in their DMI product-name,
drop the second, redundant, entry.
Fixes: a4dae468cfdd ("ASoC: rt5645: Add ACPI-defined GPIO for ECS EF20 series") Cc: Chris Chiu <chiu@endlessos.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://msgid.link/r/20231126214024.300505-2-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use hweight32() to count the CCxE bits in stm32_pwm_detect_channels().
Since the return value is assigned to chip.npwm, change it to unsigned
int as well.
This function may copy the pad0 field of struct hl_info_sec_attest to user
mode which has not been initialized, resulting in leakage of kernel heap
data to user mode. To prevent this, use kzalloc() to allocate and zero out
the buffer, which can also eliminate other uninitialized holes, if any.
The mtk_dp driver registers a phy device which is handled by the
phy_mtk_dp driver and assumes that the phy probe will complete
synchronously, proceeding to make use of functionality exposed by that
driver right away. This assumption however is false when the phy driver
is built as a module, causing the mtk_dp driver to fail probe in this
case.
Add the phy_mtk_dp module as a pre-dependency to the mtk_dp module to
ensure the phy module has been loaded before the dp, so that the phy
probe happens synchrounously and the mtk_dp driver can probe
successfully even with the phy driver built as a module.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Fixes: f70ac097a2cf ("drm/mediatek: Add MT8195 Embedded DisplayPort driver") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Guillaume Ranquet <granquet@baylibre.com> Link: https://patchwork.kernel.org/project/dri-devel/patch/20231121142938.460846-1-nfraprado@collabora.com/ Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Layout of FW version 0x0503 is compatible with 0x0502.
Already supported by TI's tas2781-linux-driver tree.
https://git.ti.com/cgit/tas2781-linux-drivers/tas2781-linux-driver/
The Vangogh machine driver variant based on the MAX98388 amplifier, as
found on Valve's Steam Deck OLED, relies on probing via an ACPI match
table. This worked fine until commit 197b1f7f0df1 ("ASoC: amd: Add new
dmi entries to config entry") enabled SOF support for the target machine
(i.e. Galileo product), causing the sound card to enter the deferred
probe state indefinitely:
The issue is related to commit e89f45edb747 ("ASoC: amd: vangogh: Add
check for acp config flags in vangogh platform"), which tries to
mitigate potential conflicts between SOF and generic ACP Vangogh
drivers, due to sharing the PCI device IDs.
However, the solution is effective only if the machine driver is
directly probed by pci-acp5x through platform_device_register_full().
Hence, remove the conflicting ACPI based probing and rely exclusively on
DMI quirks for sound card setup.
Fixes: dba22efd0d17 ("ASoC: amd: vangogh: Add support for NAU8821/MAX98388 variant") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Link: https://msgid.link/r/20231209203229.878730-2-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On 9FGV0241, the DIF OE0 is BIT(1) and DIF OE1 is BIT(2), on the other
chips like 9FGV0441 and 9FGV0841 DIF OE0 is BIT(0) and so on. Increment
the index in BIT() macro instead of the result of BIT() macro to shift
the bit correctly on 9FGV0241.
Fixes: 603df193ec51 ("clk: rs9: Support device specific dif bit calculation") Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Link: https://lore.kernel.org/r/20231105200642.62792-1-marek.vasut+renesas@mailbox.org Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Call runtime_pm_put*() if watchdog is not already started during probe and re
enable it in watchdog start as required.
On K3 SoCs, watchdogs and their corresponding CPUs are under same
power-domain, so if the reference count of unused watchdogs aren't
dropped, it will lead to CPU hotplug failures as Device Management
firmware won't allow to turn off the power-domain due to dangling
reference count.
Users report about the unexpected behavior for setting timeouts above
15 sec on Raspberry Pi. According to watchdog-api.rst the ioctl
WDIOC_SETTIMEOUT shouldn't fail because of hardware limitations.
But looking at the code shows that max_timeout based on the
register value PM_WDOG_TIME_SET, which is the maximum.
Since 664a39236e71 ("watchdog: Introduce hardware maximum heartbeat
in watchdog core") the watchdog core is able to handle this problem.
This fix has been tested with watchdog-test from selftests.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217374 Fixes: 664a39236e71 ("watchdog: Introduce hardware maximum heartbeat in watchdog core") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20231112173251.4827-1-wahrenst@gmx.net Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Avoid unnecessary crashes by claiming only NMIs that are due to
ERROR signalling or generated by the hpwdt hardware device.
The code does this, but only for iLO5.
The intent was to preserve legacy, Gen9 and earlier, semantics of
using hpwdt for error containtment as hardware/firmware would signal
fatal IO errors as an NMI with the expectation of hpwdt crashing
the system. Howerver, these IO errors should be received by hpwdt
as an NMI_IO_CHECK. So the test is overly permissive and should
not be limited to only ilo5.
We need to enable this protection for future iLOs not matching the
current PCI IDs.
When the new watchdog character device is registered, it becomes
available for opening. This creates a race where userspace may open the
device before the character device's owner is set. This results in an
imbalance in module_get calls as the cdev_get in cdev_open will not
increment the reference count on the watchdog driver module.
This causes problems when the watchdog character device is released as
the module loader's reference will also be released. This makes it
impossible to open the watchdog device later on as it now appears that
the module is being unloaded. The open will fail with -ENXIO from
chrdev_open.
The legacy watchdog device will fail with -EBUSY from the try_module_get
in watchdog_open because it's module owner is the watchdog core module
so it can still be opened but it will fail to get a refcount on the
underlying watchdog device driver.
Fixes: 72139dfa2464 ("watchdog: Fix the race between the release of watchdog_core_data and cdev") Signed-off-by: Curtis Klein <curtis.klein@hpe.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20231205190522.55153-1-curtis.klein@hpe.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently zynqmp divider round rate is considering single parent and
calculating rate and parent rate accordingly. But if divider clock flag
is set to SET_RATE_PARENT then its not trying to traverse through all
parent rate and not selecting best parent rate from that. So use common
divider_round_rate() which is traversing through all clock parents and
its rate and calculating proper parent rate.
Currently zynqmp clock driver is not calculating closest mux rate and
because of that Linux is not setting proper frequency for CPU and
not able to set given frequency for dynamic frequency scaling.
E.g., In current logic initial acpu clock parent and frequency as below
apll1 0 0 0 2199999978 0 0 50000 Y
acpu0_mux 0 0 0 2199999978 0 0 50000 Y
acpu0_idiv1 0 0 0 2199999978 0 0 50000 Y
acpu0 0 0 0 2199999978 0 0 50000 Y
After changing acpu frequency to 549999994 Hz using CPU freq scaling its
selecting incorrect parent which is not closest frequency.
rpll_to_xpd 0 0 0 1599999984 0 0 50000 Y
acpu0_mux 0 0 0 1599999984 0 0 50000 Y
acpu0_div1 0 0 0 533333328 0 0 50000 Y
acpu0 0 0 0 533333328 0 0 50000 Y
So use __clk_mux_determine_rate_closest() generic function to calculate
closest rate for mux clock. After this change its selecting correct
parent and correct clock rate.
apll1 0 0 0 2199999978 0 0 50000 Y
acpu0_mux 0 0 0 2199999978 0 0 50000 Y
acpu0_div1 0 0 0 549999995 0 0 50000 Y
acpu0 0 0 0 549999995 0 0 50000 Y
Should check return value of f2fs_recover_xattr_data in
__f2fs_setxattr rather than doing invalid retry if error happen.
Also just do set_page_dirty in f2fs_recover_xattr_data when
page is changed really.
Fixes: 50a472bbc79f ("f2fs: do not return EFSCORRUPTED, but try to run online repair") Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The amdgpu_free_extended_power_table is called in every error-handling
paths of amdgpu_parse_extended_power_table. However, after the following
call chain of returning:
amdgpu_parse_extended_power_table
|-> kv_dpm_init / si_dpm_init
(the only two caller of amdgpu_parse_extended_power_table)
|-> kv_dpm_sw_init / si_dpm_sw_init
(the only caller of kv_dpm_init / si_dpm_init, accordingly)
|-> kv_dpm_fini / si_dpm_fini
(goto dpm_failed in xx_dpm_sw_init)
|-> amdgpu_free_extended_power_table
As above, the amdgpu_free_extended_power_table is called twice in this
returning chain and thus a double-free is triggered. Similarily, the
last kfree in amdgpu_parse_extended_power_table also cause a double free
with amdgpu_free_extended_power_table in kv_dpm_fini.
Fixes: 84176663e70d ("drm/amd/pm: create a new holder for those APIs used only by legacy ASICs(si/kv)") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When radeon_bo_create and radeon_vm_clear_bo fail, the vm->page_tables
allocated before need to be freed. However, neither radeon_vm_init
itself nor its caller have done such deallocation.
Fixes: 6d2f2944e95e ("drm/radeon: use normal BOs for the page tables v4") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When ps allocated by kzalloc equals to NULL, kv_parse_power_table
frees adev->pm.dpm.ps that allocated before. However, after the control
flow goes through the following call chains:
The adev->pm.dpm.ps is used in the for loop of kv_dpm_fini after its
first free in kv_parse_power_table and causes a use-after-free bug.
Fixes: a2e73f56fa62 ("drm/amdgpu: Add support for CIK parts") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the allocation of
adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries fails,
amdgpu_free_extended_power_table is called to free some fields of adev.
However, when the control flow returns to si_dpm_sw_init, it goes to
label dpm_failed and calls si_dpm_fini, which calls
amdgpu_free_extended_power_table again and free those fields again. Thus
a double-free is triggered.
Fixes: 841686df9f7d ("drm/amdgpu: add SI DPM support (v4)") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 5104fdf50d32 ("drm/amdgpu: Fix a null pointer access when the smc_rreg pointer is NULL") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not reset Merge while using CMDQ because reset API doesn't
wait for frame done event as CMDQ does and could lead to
underrun when the layer is switching off.
Fixes: aaf94f7c3ae6 ("drm/mediatek: Add display merge async reset control") Reviewed-by: CK Hu <ck.hu@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com> Link: https://patchwork.kernel.org/project/dri-devel/patch/20231214055847.4936-23-shawn.sung@mediatek.com/ Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
